Search Documents

By System By John E. Owen, Walton J. Greer

The guard electrode system measures the resistivity of formations by employing a thin disk of current which is caused to flow perpendicular to the bore hole. The control of this current disk is obtained in a brute force manner through the use of relatively long equipotential electrodes above and below the measuring electrode. The log obtained from the system is free of "lag," "plateau," "shadow," "reflection" and other distortions evident on conventional logs. The proportionate contributions of the hole size and invaded zone resistivity to the apparent resistivity reading are reduced when the mud and filtrate resistivities are lower. Thus, the guard system favors the use of conductive muds. The mathematical development of the theory is given in an appendix. Equations are derived to evaluate the effects of mud resistivity, hole size, invaded zone resistivity and depth, and the true formation resistivity. Sample logs from several provinces are reproduced and compared with conventional electric logs to illsutrate the much greater detailed lithology that can be presented by the guard electrode system. INTRODUCTION With increased ability of those in the petroleum industry to analyze formation characteristics from electrical resistivity data, there has become apparent the need for more precise measures of that parameter. The measurement of the resistivity of a homogeneous and isotropic material can be made simply when the body of the material is infinite in all dimensions and the measuring electrodes can be placed within the body. In such a case, the current leaving an electrode follows a spherical distribution and the mathematical expression for the potential level at any distance from that electrode can readily be derived.'.' If it is considered that the active electrodes are within a bore hole filled with mud of a resistivity different from that of the formation. the current does not flow in a spherical pattern near the current source or sink, and the calculations of potential levels become more difficult. The additional consideration of a section of formation invaded by mud filtrates, and thus having resistivity different from either that of the mud, the adjacent formations or of the undisturbed formation, makes the mathematical problem extremely complex. Should the vertical dimensions of the formations be considered as finite. the problem becomes so complex as to preclude reasonable solution. Yet, even these considerations have not described adequately the conditions encountered in a large proportion of the wells to be studied. In efforts to evaluate the effects of the various conditions. combinations of twn, three. and four electrode logging con- figurations of the conventional types have been used. The resulting logs have left much to be desired in some provinces. It has become apparent that the use of such configurations will not result in adequate measurements being made, particularly in cases where the formation is composed of thin sections. If all the current of a resistivity measuring circuit is made to flow through the formation opposite the exploring electrode, many of the shortcomings of the conventional measuring system are eliminated. In the guard electrode method of electrical well logging to be discussed in this paper, the current is so controlled by causing it to flow in a thin disk normal to the axis of the logging tool. EARLY HISTORY The guard electrode method of electrical well logging in its early years was a joint development by the Geophysical Research Corp. and the Amerada Petroleum Corp. The method was first experimentally investigated by means of model studies. The results of these studies indicated that current focusing systems properly applied to electrical well logging

Jan 1, 1951

By John K. Gustafson

The title of my talk is "The Gold Miner and the Future of Gold." This title might just as accurately have been stated as "Gold and the Future of the Gold Miner." Since prehistoric times gold has been sought by mankind for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value and lubricated trade between peoples. For at least 6000 years, gold has been used to barter for other commodities. It has been prospected for, treasured, made into works of art and personal adornment, and from time to time has been the object of conquest. Because of its predominant role in recent centuries as a basis for money, economists began to think of it solely in these terms. Annoyed by the disciplinary pressure of gold on the money manager's desire to manipulate money, the famous economist, John Maynard Keynes, characterized it as a "barbaric relic of the past", a characterization repeated by William McChesney Martin, Jr., when he was head of the Federal Reserve Bank. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world.' It is the most ductile metal known. An ounce of gold, for example, can be drawn into a continuous wire over 35 miles long. It also is so malleable that an ounce of gold can be beaten into films ten one-millionths of an inch thick sufficient to cover 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of gold weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity, only slightly less than silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity both to light and infrared rays. Because of these qualities, in addition to its rare beauty, industrial and artistic uses of gold have been growing rapidly. On a world basis, a recent study estimated that in 1960 about 750 tons of gold were used for fabrication, and that the amount had grown to about 1296 tons in 1968. My objective in this talk is to discuss with you the present and future supply of and demand for gold on a worldwide basis and the effect these forces are likely to have on the price the miner can expect to receive for the gold he produces. This is a highly controversial and risky subject to discuss before any audience. Nevertheless, it is a subject that I live with constantly as Chairman of the

Jan 1, 1972

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By John Wulff

In a previous paper Burwell and Wulff1 have shown by electron diffraction studies that allotropic transformations can be induced in 18-8 stainless steel by polishing to a depth of about 5 X 10-5 cm. The development of a successful etching technique, which removes accountable amounts of metal from the surface without pitting and without changing the root-mean-square profile as measured with an Abbot pro-filometer, led to the application of the whole technique and material to an investigation of various mechanical methods of surface preparation, such as grinding, lapping, superfinishing and cold-rolling. Ideally suited to such a study is 18-8 of low carbon and nitrogen content. The material can be heat-treated to produce a coarse-grained single-phase structure. On cold deformation there occurs not only a reduction in grain size but, at regions of maximum stress, a change of face-centered material to body-centered material, provided the metal is worked below about 200°C. When worked between 200"about and 415°C., diffraction studies evidence a reduction in grain size without the appearance of any new body-centered ferrite. Ferrite, which can be referred also to strains induced by carbide precipitation, is evident when the material is worked at temperatures between 4150 and 800°C. Stainless steel is advantageous because the usual surface-finishing operations do not readily oxidize it to any appreciable depth. In order to produce detectable oxide films on the surface of austenitic 18-8 in a time equivalent to that required to produce, for example, a fine ground finish on 1/2 sq. in., the sample must be held in a furnace or oxygen stream above 600°C. By using longer heating times, it is possible to achieve measurable oxide films on samples , whose surface temperatures exceed only about 250°C. Experimental Procedure The apparatus, material, and technique described in the previous paper1 were employed in this investigation. Samples of 18-8, I by I cm. by 4 mm., were carefully annealed in the austenitic range to produce a coarse-grained structure. They were then quenched and pickled to remove scale, On a lapping machine of the Graton2 type, both sides of each sample were polished to a a of 1/6 a wave length of sodium D light. Thereafter they were electrolytically etched to remove at least 1 X 10-3 cm. of the surface, a depth that is well below that of any defermations induced by surface preparation. samples of this material, carefully mounted in steel holders, were then sent to various industrial organizations known for special finishing techniques. In the instrue ment shops at the Massachusetts Institute of Technology check samples were finished by the same methods, as far as they were available. Abbot profilometer3 readings Were made on all the samples, which were then carefully degreased in double distilled benzine and alcohol, dried in a hot-filtered air blast, and kept in a desiccator. SUC-

Jan 1, 1941

By G. D. Hobson, I. Mrosovsky

Material balance relationships for expansion-type reservoirs above the bubble point have been discussed in recent years by H. N. Hall and M. F. Hawkins, Jr. The former drew attention to the effects of rock compressibility, and the latter to the effects of the compressibility of any interstitial water. Hawkins derived a general relationship which took note of oil, water and rock compressibilities, and then by assuming first, the absence of interstitial water and secondly, no effects due to interstitial water or rock compressibility, obtained relationships symbolically of the same form as those previously derived directly by Hall. Hawkins defined his terms clearly, and noted an approximation, due to the omission of a term involving the product of two compressibilities, made in reaching his final equation. There is, however, possible ambiguity with regard to Hall's written definition of the oil production term. One interpretation would mean that the produced oil and initial oil-in-place, if both required as stock tank barrels, would be obtained by using different formation volume factors in the conversion in order to satisfy the conditions implicit in Hall's formulae. The other would involve an approximation which, if used, was not stated. In both Hall's and Hawkins' studies the effect of the approximation or inconsistency is very slight. Nevertheless, it may be justifiable to give a somewhat more consistent derivation, since the complexity of the final relationships is not thereby greatly increased. Let the initial pore volume be Vi and the volume after a pressure drop of Ap, V. Then V = V, (1 - ?p . cr), where c, is the rock compressibility expressed as change in pore volume/unit pore volume/unit pressure change, and is defined with the initial pressure as base. Suppose that the interstitial water saturation under the initial conditions is Sw. The total volume of interstitial water under those conditions will be ViSw. If the volume of the water after dropping the pressure by ?p is V., this will be given by Vw = ViSw (1 + ?p.c,w), the compressibility of the water being c, which is ex- pressed using the volume at the initial pressure as base. If Boi is the reservoir volume factor of the crude oil for the initial reservoir conditions, and B. the equivalent factor when the pressure has dropped by ?p, with N the initial amount of oil expressed as stock tank barrels. N.Boi = Vi - V,Sw If n is the amount of oil produced (in terms of stock tank barrels) as a result of the pressure drop ?p, the remaining subsurface volume of oil at the lower pressure will be Bw, and Bc can be related to the compressibi:ity of oil and the pressure drop, and if c, is the compressibility factor based on the initial conditions, The relationship derived by Hawkins was case to a standard at the lower pressure, while a term (Ap) had been dropped, because of its smallness arising from its dependence on the products of two compressibility factors. When there is no interstitial water and rock compressibility can be ignored, Eq. 1 reduces to:

Jan 1, 1957

By Peter Nalle

12.3-1. Reporting. NEED. It seems almost unnecessary to comment on the need for reporting research and development results and activities, and yet much of the difficulty and misunderstanding surrounding a Research and Development (R&D) group results from poor or nonexistent reporting. Certainly no evaluation can be made without reports of results or plans. It is as important to report accurately and fully for the department's own use as it is for external use. Research unreported might as well be considered research undone. This section will discuss, in part, the need for reporting, the general types of reports which may be generated to satisfy the need, and finally, the evaluation of a project as judged by various commonly used standards. PURPOSE. Some specific observations might be appropriate concerning the reporting of R&D results. The requirements and background of the group receiving the report must be considered. A particular report is usually directed towards the background of a particular group, such as ((technical," "operational," "financial," or "marketing." It is essential that the emphasis and coverage be geared to the training of people receiving the report. It should be obvious that the financial department will be less interested in the technical details of the process and more interested in the capital funds and tax implications involved in the project. Operating personnel will be greatly interested in the effects of a new method on mining plans, and so on. This does not mean that the reporting in any way should slight pertinent details, nor should a patronizing attitude be assumed by the writer. However, it is essential that the needs of the reader be recognized. For reports that might have large and varied distribution, it is often feasible to group, either as sections or appendixes, the special details and information of interest only to certain functions within the organization. A

Jan 1, 1968

By G. W. P. Rengstorff, H. B. Goodwin

A method is described for purifying iron in batches of 150 Ib or more. Oxygen, carbon, nitrogen, and sulphur are removed from flakes of electrolytic iron by treatment in wet and then dry hydrogen. A special consumable-electrode arc furnace is used to remove hydrogen and to melt the flakes into ingots. A LTHOUGH iron and steel have been made and used for hundreds of years, there are still wide gaps in the knowledge of these metals. One reason for this is that the true properties of the base metal, iron, are not well known, simply because really pure iron has never been readily available for research purposes. Commercial iron, and even the "pure" irons which are readily available, are really complex alloys of iron with oxygen, nitrogen, hydrogen, carbon, sulphur, silicon, and other elements. With such materials, it has not been possible to prepare steels and other iron-base alloys in which all elements are present in exactly controlled amounts. It is an almost impossible task to determine the separate effects of each element or the intereffects of several elements unless alloys can be prepared containing only the desired elements. The ability to make controlled alloys of low impurity content is of far more than academic interest. It will assist in the study of such practical problems as the brittle failure of ship hulls or high pressure gas pipelines, determination of the factors which affect the deep-drawing properties of steels, the improvement of magnetic and electrical properties, the phenomenon of aging, and many others. In 1949, the American Iron and Steel Institute asked Battelle Memorial Institute to prepare high purity iron on a larger scale than had been attempted up to that time. The work was directed toward the preparation of iron as low as possible in carbon, oxygen, nitrogen, hydrogen, and sulphur because these are the contaminating elements of major interest in many research investigations on iron-base alloys. The initial goal was to prepare iron with not more than a few thousandths of one percent of each of these impurities. The purpose was to set up a "bank" of high purity iron on which researchers could draw when a supply was needed and which could be replenished from time to time as the stock became depleted. Of several possible purification methods, heating in hydrogen was selected as the most promising for the removal of both carbon and oxygen from solid iron. Metallic impurities are not removed by hydrogen. Electrolytic iron was chosen as a starting material because it is the most readily available form of iron low in metallic impurities. Decarburization and desulphurization were obtained by annealing in wet hydrogen at relatively low temperatures. The optimum temperature, as found by previous investigators,' is about 1400°F. This treatment also removes nitrogen. Deoxidation is favored by dry hydrogen and higher temperature. There is evidence from previous work that an anneal at 2200°F in dry hydrogen will deoxidize the iron, reduce the nitrogen content, and reduce the sulphur content. These facts suggested the use of a two-stage process: treatment in wet hydrogen followed by treatment in dry hydrogen. To carry out the purification process in a reasonable time, it was necessary that the iron be in thin pieces. Flakes of electrolytic iron were used. Because most research requires that the iron be in massive form, it was nccessary to melt the purified iron to consolidate it into large pieces. For this work, it was decided to prepare ingots weighing at least 15 lb by using a cold hearth arc-melting process in which the iron was melted in an inert atmosphere of argon or helium. This method of melting was selected because the water-cooled copper crucible is not wet by the iron and does not contaminate it as a refractory crucible would. Because the crucible is also the ingot mold, contamination from mold materials was also eliminated. Contamination from electrodes was avoided by making them from purified electrolytic iron. The melting procedure finally developed was an adaptation of the Kellogg electric ingot process.' Two batches of purified iron weighing about 100 Ib each in ingot form were prepared with analyses as shown in Table I. The remainder of this paper describes the procedures in more detail. In general, the process con-

Jan 1, 1956

By Eugene H. Cowles

The German silver industry of the United States amounts in value to upwards of $6,000,000 or $8,000,000 annually. Several thousands of people earn a livelihood pursuing it, and the beautiful goods and articles manufactured from this time-honored and valued alloy are everywhere visible. German silver enters largely into our street signs, harness and house hardware, and all manner of table-ware, solid or plated. There is scarcely an hour in the day that German or nickel-silver is not before our eyes. The composition of this alloy is a very uncertain thing, and depends largely on the honesty of the manufacturer and the price the purchaser is willing to pay. It is composed of copper, zinc and nickel in varying proportions. The best varieties contain from 18 to 25 per cent. of nickel, and from 20 to 30 per cent. of zinc, the remainder being copper. The more expensive nickel-silver contains from 25 to 33 per cent. of nickel, and from 75 to 66 per cent. of copper. The nickel is used as a whitening element; it also strengthens the alloy and renders it harder and more non-corrodible than the brass made without it, of copper and zinc. Moreover, it reduces the odor emanating from brass, which is so disagreeable if it occurs about the dining-table. Of all troublesome alloys to handle in the foundry or rollingmill, German silver is the worst. It is unmanageable and refractory at every step in its transition from the crude elements into rods, sheets or wire. As a white-headed furnace-man recently said to the writer, in one of our large mills, " you can put eight crucibles into the fire, each containing exactly the same mixture of German silver, and when you take them out and pour them into slabs for rolling, seven will be a mass of scum or slag, or the stuff will swell up like rising bread and overflow the moulds, and be so full of blow-holes that it will look like a sponge. The eighth crucible will contain perfectly good metal. On remelting the next day, the bad stuff will, in nine chances out of ten, come out just as good metal as the eighth pot the day before, and under apparently the same conditions." With nickel at seventy or eighty cents per pound, German silver

Jan 1, 1890

By S. W. Parr

THE low-temperature carbonization of coal involves the carrying out of the coking process under conditions wherein neither the coal mass nor any of the passageways through which the volatile products pass are heated above 700° or 800° C. For convenience in this discussion, the single number 750° will be used to designate the maximum range. This temperature is not selected arbitrarily; it is the result of certain natural conditions that are inherent in the substances involved. Two of these conditions arc sufficiently pronounced to suggest a line of demarcation at this point as follows: (1) Below 750°, all the heavy hydrocarbons are expelled, which means that, at these lower temperatures, the illuminants, the gases of high calorific value, and the condensible oils are discharged; above 750°, there are given off the lean, non-illuminating gases consisting for the most part of hydrogen and marsh gas and having no condensible constituents present. (2) Below 750°, there is substantially no secondary decomposition; above 750°, the volatile products are readily decomposed, forming tars, naphthalene, free carbon, etc. It is not intended to maintain that no secondary decompositions occur below 750°. Many recent studies have demonstrated the practicability, especially in the presence of catalytic substances, of cracking certain of the hydrocarbon compounds; but at these lower temperatures the step is a moderate one, as, for example, from xylene to toluene or from toluene to an anthracene. These changes are moderate in amount. Not only do the reactions proceed slowly but they are subjected to the decomposing conditions for only a short time. This is evident when it is recalled that at these initial temperatures the decomposition, of the coal is very rapid and, if anywhere near a neutral pressure is maintained, the movement

Jan 2, 1920

By William E. Ford, Edward Salisbury Dana

436. Electrical Conductivity. - The subject of the relative conducting power of different minerals is one of minor interest.* In general most minerals, except those having a metallic luster among the sulphides and oxides, are non-conductors. Only the non-conductors can show pyro-electrical phenomena, and only the conductors can give a thermo-electric current. 437. Frictional Electricity. - The development of an electrical charge on many bodies by friction is a familiar subject. All minerals become electric by friction, although the degree to which this is manifested differs widely. There is no line of distinction among minerals, dividing them into positively electric and negatively electric; for both electrical states may be presented by different varieties of the same species, and by the same variety in different states. The gems are in general positively electric only when polished; the diamond, however, exhibits positive electricity whether polished or not. It is a familiar fact that the electrification of amber upon friction was early observed (600 B. C.), and indeed the Greek name

Jan 1, 1922

By Phillip Philbin, Frank E. Senftle

A field neutron activation analysis technique suitable for determining uranium in ores has been tested. The method is based on the measurement of the 74.7 keV gamma ray from 'U. When the thorium/uranium ratio is greater than one or the vanadium is greater than 1%, a low uranium analysis is obtained. No satisfactory correction for thorium has been found, but a correction for vanadium can be deter¬mined. For ore containing greater than 0.01% uranium, the uranium can be deter¬mined with an accuracy of about 10% which is quite adequate for a field exploration technique.

Jan 1, 1972

R. Schuhmann, Jr. (Purdue University)— Fulton and Chipman's results on rate of silica reduction from slags are analogous in many was to the results of Parlee, Seagle, and Schuhmann10 on rate of alumina reduction from alumina crucibles. Both investigations have given comparably low rates of reduction and slow approaches to equilibrium. Accordingly, we may hypothesize that the rate-determining step is the same in both kinds of experiments; that is, oxygen diffusion across the stagnant boundary layer on the liquid-metal side of the interface between the liquid metal and the oxide phase (slag or solid oxide). I suggest that silica reduction involves the following consecutive steps: I) At the slag-metal interface: SiO2(slag) Si+ 20 II) Transport of oxygen from slag-metal to gas-metal interface: a) diffusion across liquid-metal boundary layer at slag-metal interface. b) convection within the body of liquid metal. c) diffusion across boundary layer at metal-gas interface. 111) At the metal-gas interface: C +O- CO (gas) Iv) At the graphite-metal interface: C (graphite) -C At steelmaking temperatures it is reasonable to assume that equilibrium is attained in all three chemical reactions (I, 111, and IV) right at the respective interfaces. Convection within the stirred liquid metal (step IIb) is also rapid. Transport of Si and C should be orders of magnitude easier than transport of 0, because of the relatively high concentrations of Si and C. Accordingly, we might expect the overall reaction rate to be determined by boundary-layer diffusion of oxygen, either IIa or IIc. Fulton and Chipman's demonstration that bubbling CO through the system had no major effect on reaction rate indicates that IIc is not the slowest step. Therefore, it becomes logical to estimate the maximum rate for step IIa and to compare this theoretical estimate with Fulton and Chipman's experimental data. If oxygen diffusion across the liquid metal boundary layer at the slag metal interface (step IIa) is rate-determining, In this equation, dn sio, /dt is the rate of silica reduction in moles per sec,A is the area of slag-metal interface in sq cm, Do is the diffusivity of oxygen in sq cm per sec, 6, is the boundary layer thickness in cm, c,* is the oxygen concentration right at the slag-metal interface in moles per cubic cm, and co is the oxygen concentration in the body of the liquid metal, also in moles per cubic cm. Equilibrium data" on the silicon deoxidation reaction in liquid iron and steel at 1600°C indicate that the oxygen contents of the liquid metal in Fulton and Chipman's experiments at 1600°C probably fell in the range of 0.5 x10-3 x10-3wt pct. That is, the maximum conceivable value of co*-co for the system under consideration was on the order of 10"5 mole oxygen per cubic cm. On the basis of previously published data,1O,11 it is estimated that Do/0 will fall somewhere in the range from 10-3 to 10-1 cm per sec. The surface area A in Fulton and Chipman's experiments was approximately 20 sq cm, and the weight of metal involved was about 500 grams. Combination of all these figures with the above rate equation leads to an estimate that the rate of silica reduction should fall within the range from 0.002 to 0.2 wt pct Si per hr. This estimate is consistent with the experimental data. For example, Fulton and Chipman's Fig. 2 shows a change of about 0.3 pct Si in 10 hr, corresponding to an average rate of 0.03 pct per hr. According to the proposed hypothesis, increasing the temperature will increase the reaction rate ill two ways: 1) by increasing oxygen diffusivity and 2) by increasing the oxygen concentration (oxygen solubility) in the liquid metal. The combination of these two effects accounts for the high value of the observed activation energy. Summarizing, I propose that the rate of silica reduction, like that of the carbon-oxygen reaction, is diffusion controlled and that low oxygen concentration in the liquid metal is the major factor accounting for the very low observed rates of silica reduction. John Chipman (author's reply)—The authors thank Professor Schuhmann for his interesting contribution. His proposed explanation may well prove to be the correct one. There is clearly a need for much further experimental work on this problem, and further research is in progress.

Jan 1, 1961

By Eric Jette

IN thermodynamic studies of gas mixtures and liquid solutions, the respective problems have been greatly simplified by the use of two general limiting laws; Dalton's law of partial pressures and Raoult's law. It is generally recognized that these two laws have a common physical and chemical basis which may be stated as follows: The law may be expected to be strictly valid only for systems in which the different molecular species are so nearly the same in their physical and chemical properties that a molecule is unable to recognize whether its neighbor is one of its own kind or not. Positive and negative deviations from both laws are frequently encountered. The occurrence of negative deviations in both gases and liquids is ascribed to attractive forces which, in the more extreme cases, may be so large in magnitude and so highly specific in character as to lead to the formation of definite chemical compounds. Positive deviations in gases develop only at higher pressures where the intermolecular distances are so decreased that factors such as molecular size and shape, which ultimately become concerned with the repulsive forces, come into play. In liquid mixtures, positive deviations are generally considered as due to differences in the symmetrical (nonpolar) fields of force which surround the various molecular species and which are supposed to give rise to a tendency for each species to associate with its own kind and thus to "squeeze out" the other variety. Fundamentally this also involves the existence of repulsive forces between unlike molecules. If the fields of force are unsymmetrical (polar) a tendency towards compound formation results. Stated in more exact terms, strict adherence to the law means that the "activity" (or any adequate measure of this quantity) of a component in a mixture is a linear function of the molecular (or atomic)

Jan 1, 1934

IN order to make his work easier, every master of any art whatever keeps always to the road that he has learned or that his skill or good judgment has shown him to be the best. Although there are various methods used in making moulds for guns, depending on whether they are large or small, nevertheless almost the same road is traveled in all. You must first know that it is necessary to make a pattern of wood or clay exactly as the gun is to be, with those ornaments of cornices and rings that you wish to be in the bronze. Let us suppose that you wish this pattern to be of wood. You must try to have for this a piece of fir as long and thick as you wish, dry, solid, and well seasoned, with few or no knots if possible. This should be longer than the gun by the length of the head and foot rests where it is pivoted [83v] so that it can be turned as on a lathe. On the end where the mouth is to be it should project out enough so that you can attach a feeding head at the top of the casting. You can make or have this pattern made round, fluted, spiral, or half fluted, as you like best, making the measurements exactly correct with all care and attention. Then two bearing trestles must be fixed firmly in the ground, one at the head and one at the foot, as is usually done with roasting spits and as you see drawn here. This done, if it is fluted, put the cornice pieces at the place where you wish the mouth to be and at the foot where the fire is applied. These are

Jan 1, 1942

THE second operation in the art of casting, and one of the greatest importance, is that of melting and thoroughly liquefying the materials of which you wish to make your casting. On this operation depends the whole outcome of your intentions and the perfection of your work. Without it, even though you had a great abundance of moulds and vast quantities of bronze, your desires, labor, and expense would all be in vain. In this operation I find on consideration that, in addition to experience, there are three necessities-perhaps indeed four-that must be provided without fail. The first is the furnace or other agent which contains the fire and the metal brought together. The second is the wood or charcoal which is the necessary and proper nutriment of the fire, from whose virtues are derived the greater or lesser forces which, according to their kind, are ready to effect what is required. The third is to have the materials disposed to easy fusion by means of corruption, alloying, or by their own nature. The fourth, as the motivating cause of the whole, could perhaps be listed as the first-this is the ingenuity and good judgment of the worker, together with the bodily exertions not only of himself but also of his helpers in addition. For, besides a certain ordinary caution, it is necessary to pay particular attention, first, to see that the furnaces, machines, ladles, hearths, refineries, and other kinds of instruments or similar vessels be made so as to dispose the metals for melting, and, when melted, that they easily maintain them so. These should also be prepared in such a way that they cannot be injured by the fire, for if they should be damaged the operation would fail. In order to do this, it is first necessary that you arrange the instruments with forethought and action so that the power of the fire can operate. Fire operates on things only when brought together with them in long-continued operation, or when driven by a great force of wind. It burns many things and softens others, but it makes the metals as liquid as water.

Jan 1, 1942

By H. F. Mills

The Iron King mine is I2 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped unti1 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of I40 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Dcnn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular. no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 80 ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 920-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1949

By H. F. Mills

The Iron King mine is I2 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped unti1 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of I40 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Dcnn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular. no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 80 ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 920-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1949

By H. F. Mills

THE Iron King mine is 12 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped until 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of 140 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Denn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular, no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 8o ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 92o-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1947

By C. L. Dake

Chemistry of Iron Solution IRON is much more soluble in the ferrous than in the ferric form. Where, as in the case of the ferrous silicates and the sulphides, the iron is already in the ferrous form, it may go at once into solution and be removed, upon the breaking down of the parent rock. If in the ferric form, it must first be reduced; usually by the decay of organic matter, the demand of the decaying carbonaceous matter for oxygen being so great that the latter is abstracted from the ferric compounds and the iron is thereby reduced and rendered' soluble. The iron may go into solution as the sulphate, or in the presence of excess CO2 as ferrous carbonate. It is probably soluble as salts of the organic acids.1 Recent work indicates that these are important in the formation of bog ores.2 There is considerable variety of opinion concerning the behavior of these organic compounds.3 The secretions about the roots of plants and trees also cause the solution and removal of iron and a consequent bleaching of the soil.4 While the matter is not yet well understood, we can probably say definitely that the so-called organic acids are a group of colloids which possess slightly acid properties, and the salts of which are partly soluble

Jan 7, 1915

By P. C. J. Gallagher

A number of recmt determinations for the ratio of extrinsic to intrinsic stacking fault energy in fcc solid solutions are examined. Some of these arise from incomplete analyses which can yield only approxi?nate values for the ratio. Reliable results, on the other hand, obtained using extrinsic-intrinsic fault pairs, show that the extrinsic and intrinsic fault energies are essentially equal in several materials. There is some reason to believe that this finding is of general applicability to fcc elements and alloys. A wide range of values has been obtained for the relative magnitudes of the extrinsic and intrinsic stacking fault energies (yext and yint, respectively) in recently published studies in a variety of materials. In contrast, Hirth and Lothe' using a central force model have shown that out to tenth nearest-neighbor interactions the perturbation in energy caused by both types of fault is the same. Although the model used is not completely valid in metals, there is nevertheless some indication that marked variations of yext/nnt should not be observed from one material to another. In early work in Cu-A1, Cu-Ge, Ni-Co, and stainless steel all the deformation faults observed in the electron microscope were found to be intrinsic in nature, which led to an attitude that the extrinsic fault energy must be considerably greater than the intrinsic. Extrinsic faulting arising from deformation has, however, more recently been directly observed in Au-4.8 at. pct n;~ Ag-6 at. pct Sn and Ag-8 at. pct sn; Ag-7.5 at. pct In and Ag-11.8 at. pct 1n;"' pure silwer and Ag-0.5 at. pct ~n;' and Cu-22 at. pct Zn, Cu-30 at. pct Zn, and Cu-7.5 at. pct ~1.l' Multilayer loops containing extrinsic faulting have also been observed in quenched aluminum." While peak asymmetries in X-ray faulting probability studies were generally attributed to the presence of twins,Lelel2 has recently reinterpreted earlier X-ray data in Ag-Sb alloysU in terms of the presence of extrinsic faulting. The determinations of yeXt/yint made from the above studies are shown in Table I, with a brief description of the techniques employed. A number of the methods utilized are deficient in one or more respects, and the reliability of the values listed will be discussed. ~ele'~ recognizes that his approximate determinations of yext/yint assumes equal numbers of extrin-sically and intrinsically faulted dislocations. It is well-known, however, that such an assumption is not at all justified since extrinsic faulting has but rarely been observed in samples studied in the electron microscope. The only conclusion that should be drawn from the X-ray results at present is that the total intrinsic scattering cross section (i.e., the product of the width of the intrinsically faulted dislocations with their density) is approximately ten times greater than for extrinsic faulting in these particular samples. An important point is that the relative magnitudes of the energies cannot be inferred from results of this type, unless the intrinsic and extrinsic faults form with equal ease. One must recognize that, although a formation barrier may restrict the amount of extrinsic faulting which occurs, this in no way implies that the extrinsic and intrinsic energies should be different. It is unlikely that a worthwhile estimate of the relative densities of extrinsically and intrinsically faulted dislocations can be made at the high deformations present in X-ray samples. ~oretto,'~ from a statistical argument applied to the nonobservation of extrinsically faulted tetrahedra out of a large sample, concluded that yeXt/yint could not be less than -4.5. However, the present author feels that a high-energy formation barrier as just supposed also explains this finding satisfactorily and that no conclusion can possibly be drawn concerning the actual extrinsic stacking fault energy. The same argument also serves to explain the fact that extrinsic faulting has been relatively little observed in the electron microscope. Extrinsic-intrinsic node pairs and isolated extrinsic nodes were first reported by Loretto~ and subsequently by Ives and Ruff,' Gallaher,' and Gallagher and Wash-burn.' Ives and Ruff' found a wide spread in the ratio of extrinsically to intrinsically faulted area in the node pairs they observed, and drew the very tentative conclusion that yeXt/yint 2 2. They recognized that a straightforward comparison of the size of the faulted areas could provide no more than a qualitative result without a theoretical analysis of the dislocation geometry associated with extrinsic faulting. A theoretical

Jan 1, 1969