Search Documents

By P. E. Fitzgerald, Dana G. Hefley

An apparatus has been developed which permits selective acidizing of producing formations and determination of the relative permeability of a formation by fluid injection. This apparatus, known as the "Electric Pilot," is an electrical fluid-interface locator, the electrical circuit of which is completed when the elec-tcodes in the well are in contact with a conductive fluid, but is not completed when immersed in a nonconductive fluid. Results are given for a number of typical acidizing applications in which the interface locator was used to control the acid. Description of the method used in making a permeability survey and the data obtained are also included. Introduction Early in the development of the acidizing industry it was recognized that one of the most important problems to be solved in the chemical treatment of any well was the determination of what part of the exposed section in the well should be treated and the selection of the technique that would insure treatment of the desired section. One of the first techniques adopted for assisting in proper placement of the acid, which is still widely used, is the method of confining the acid to the producing section by means of a column of oil, which is known as the Carr1 method of treatment, named for its inventor. In the Carr method it is not possible to selectively acidize a specific horizon in a multiple pay zone, so many improvements and modifications of the basic Carr technique were devised to accomplish this result. In order to overcome the possibility of the acid entering an undesirable section at the bottom of the well, organic gel plugs2 were introduced into the bottom of the well, which served to halt the entrance of the treating solution into these zones.3 These chemical gels later liquefied because of bacterial action and were removed from the well with the produced fluid. In fields where a gas cap existed, as in the Goldsmith field of Ector County, Texas) it was imperative that a treating technique be evolved that would confine the acid to the oil-producing zone below the gas cap. By so doing the oil-productive capacity of the wells could be improved without greatly increasing the gas production and this would lower the gas-oil ratio of the well. ~h, technique employed4 to achieve this effect utilized two pumps, one for pumping the chemicals down the tubing, the other to simultaneously force oil down the annular space to confine the acid to the oil pay, thus preventing the chemicals from entering the upper gas-bearing zones. Experience has indicated that gas wells and certain types of oil wells respond better to ''stage treating.'' This technique utilizes the introduction of a certain volume of acid and then allows the well to ''clean up99 before introduction of the next and usually successively larger stages. Where such methods are employed steps must be taken to keep a disproportionate share of the acid from entering the most permeable and previously treated Zones. A special tool

Jan 1, 1944

By P. E. Fitzgerald, Dana G. Hefley

An apparatus has been developed which permits selective acidizing of producing formations and determination of the relative permeability of a formation by fluid injection. This apparatus, known as the "Electric Pilot," is an electrical fluid-interface locator, the electrical circuit of which is completed when the elec-tcodes in the well are in contact with a conductive fluid, but is not completed when immersed in a nonconductive fluid. Results are given for a number of typical acidizing applications in which the interface locator was used to control the acid. Description of the method used in making a permeability survey and the data obtained are also included. Introduction Early in the development of the acidizing industry it was recognized that one of the most important problems to be solved in the chemical treatment of any well was the determination of what part of the exposed section in the well should be treated and the selection of the technique that would insure treatment of the desired section. One of the first techniques adopted for assisting in proper placement of the acid, which is still widely used, is the method of confining the acid to the producing section by means of a column of oil, which is known as the Carr1 method of treatment, named for its inventor. In the Carr method it is not possible to selectively acidize a specific horizon in a multiple pay zone, so many improvements and modifications of the basic Carr technique were devised to accomplish this result. In order to overcome the possibility of the acid entering an undesirable section at the bottom of the well, organic gel plugs2 were introduced into the bottom of the well, which served to halt the entrance of the treating solution into these zones.3 These chemical gels later liquefied because of bacterial action and were removed from the well with the produced fluid. In fields where a gas cap existed, as in the Goldsmith field of Ector County, Texas) it was imperative that a treating technique be evolved that would confine the acid to the oil-producing zone below the gas cap. By so doing the oil-productive capacity of the wells could be improved without greatly increasing the gas production and this would lower the gas-oil ratio of the well. ~h, technique employed4 to achieve this effect utilized two pumps, one for pumping the chemicals down the tubing, the other to simultaneously force oil down the annular space to confine the acid to the oil pay, thus preventing the chemicals from entering the upper gas-bearing zones. Experience has indicated that gas wells and certain types of oil wells respond better to ''stage treating.'' This technique utilizes the introduction of a certain volume of acid and then allows the well to ''clean up99 before introduction of the next and usually successively larger stages. Where such methods are employed steps must be taken to keep a disproportionate share of the acid from entering the most permeable and previously treated Zones. A special tool

Jan 1, 1944

By T. K. Perkins, L. R. Kern

A study of fluid mechanics, rupture of brittle materials and the theory of elastic deformation of rocks shows that, for a given formation, crack width is essentially controlled by fluid pressure drop in the fracture. Operating conditions which cause high pressure drop along the crack (such as high injection rate and viscous fluids) will result in relatively wide cracks. Conversely, operating conditions which cause low pressure drop (low injection rates and thin fluids) will result in relatively narrow cracks. Charts and equations have been derived which permit the estimation of fracture widths for a variety of flow conditions and for both horizontal and vertical fractures. INTRODUCTION There has been considerable speculation concerning the geometry of hydraulically created fractures in the earth's crust. One of the questions of practical importance is the width of fractures under dynamic conditions, i.e., while the fracture is being created and extended. Such width information could be used, for instance, to help estimate the area of a fracture generated under various conditions. Also, there has been a recent trend toward the use of large propping partiles.13, 15 Therefore is is desirable to know what factors can be varied in order to assure entry of the large particles into the fracture. There has been some work on fracture widths reported in the literature. In particular, there have been several Russian publications dealing with this sub-jeCt.1.31,3 These papers have dealt principally with the elastic theory and the application of this theory to hydraulic fractures. These studies have not led to an engineering method for estimating fracture widths under dynamic conditions. A recent paper3 has reviewed and summarized the Russian concepts. An earlier paper- from our laboratories also discussed the application of the elastic theory to hydraulic fractures. This first approach, based largely on photoelastic studies, has proved to be too simplified to accurately describe the fracturing process. However, these early thoughts have served as a guide during the development of more exact concepts. We would like to present in this paper our current concepts regarding fracture widths and some estimates of hydraulic fracture widths for several conditions. We believe that it is now possible to predict with fair accuracy the factors influencing fracture widths. Furthermore, the method of prediction has been reduced to a simple and convenient graphical or numerical calculation. CRACKS IN A BRITTLE, ELASTIC MATERIAL Many investigators2, 4, 30 have shown that competent rocks behave elastically over some range of stresses. Of course, if the tensile stress imposed upon a rock exceeds some limiting value, then the rock will fail in tension. In similar manner, there are some limiting shear stresses that can be imposed upon rocks. Hubbert and Willis11 have discussed the shear conditions which will lead to failure. Under moderate stress conditions (such as those likely to be encountered when hydraulically fracturing) and when stresses are rapidly applied, relatively, most rocks will fail in a brittle manner. Hence, for this discussion of hydraulic fractures in the earth's crust, we assume the rocks behave as brittle, elastic materials. Let us develop the discussion in the following way. (The following thoughts are applicable only to brittle materials.) 1. First we consider a brittle, elastic system. An energy balance will show the minimum pressure necessary to fracture rock, and from this pressure we calculate the minimum crack width resulting from extension of a hydraulic fracture. 2. Then we will show that, under ordinary fracturing conditions, fracture widths are appreciably greater than the minimum widths of extending fractures. In fact, we will find that crack width is controlled by fluid pressure drop in the fracture. 3. We will discuss pressure drops in fractures and resulting crack widths for various operating conditions and both vertical and horizontal fractures. 4. Finally, we will discuss the significance of these concepts, their relationship to fracturing pressures, etc. First, consider minimum fracture extension pressures. We can shed some light on this question by considering the theory proposed by Griffith7, 8 Yo explain the rupture of brittle, elastic materials. Griffith recognized that solid materials exhibit a surface energy8 (similar to surface tension in a liquid). The fundamental concept of the Griffith theory is that, when cracks spread without the application of external work (in the interior of an elastic medium which is stressed

Crushed limestone is now being "de-dusted" at the Warner Co. plant in Bellefonte, Pa., by a new high-efficiency classifier utilizing aerodynamic principles not previously employed in classifiers. Crushed limestone for certain glass industry requirements must not have more than 10 pct fines in the overall aggregate, and it is the function of the new-type classifier to separate these fines from the coarse material. During the development of this classifier by the Buell Engineering Co. of New York, it was found to have possible applications for separating pulverized coal, sintered metals, ores, mineral flours, and fillers, among other items. Limestone from Warner's deep mine is initially crushed and particles larger than 3/8-in. mesh are burned in kilns to provide calcium oxide for the chemical industry. The 3/8-in. screenings are dried and crushed to -16 mesh for use by the glass industry. For those applications requiring a minimum of fines, no more than 10 pct -100 mesh material is allowable in the end product. Hence the need for high-efficiency separation.

Jan 11, 1960

By F. C. Schora, H. P. Meissner

COUNTERCURRENT staged processes involving chemical reactions between solid and gas streams are becoming more common. Such operations are generally carried out in a series of fluidized beds with each bed acting as a stage. Fig. 1 is a schematic illustration of a series of stages located in a single column, with a solid stream moving down through this column from stage to stage counter to a rising gas stream. The reduction of iron oxides with hydrogen and carbon monoxide is one of the reactions which can be advantageously carried out in such a countercurrent system. Calculation of the performance of a countercur-

Jan 1, 1961

By Edward Nichols

As far as known to the writer, no discovery has heretofore been made in the United States of deposits of beauxite, or the hydrated oxide of alumina. The deposit which forms the subject of this note was discovered in Floyd County, Georgia. Numerous "float" specimens, covering an area of about half an acre, indicate the location of the main deposit, which has thus far been opened to an inconsiderable extent only. The excavations show the beauxite to exist apparently as large masses in clay. The formation is Lower Silurian, as determined by the Geological Survey of Georgia. The surface in the immediate vicinity is covered with numerous angular fragments of chert, which is a characteristic rock throughout this formation in Georgia. An examination of the mineral shows it to have the oolitic structure common to several beauxites. It. varies in color from a light salmon to dark red, depending upon its contents of iron oxide. The light-colored specimens are comparatively soft, while the dark mineral is much harder, spots in the latter being

Jan 1, 1888

By Donald E. Ackerman, Norman B. Pilling

The solubilities of a series of experimental alloys covering the range 0 to 100 per cent. Ni, 0 to 30 per cent. Cr have been studied under conditions of complete submersion in several fully aerated acid solutions, and in solutions containing sulfurous acid. In nonoxidizing, hydrogen-discharging acids, if the nickel content is below a certain critical amount, chromium increases the rate of solution and nickel decreases this rate; this critical content of nickel is about 13 per cent. Alloys containing more than this corrode at a constant minimum rate independent of iron, nickel or chromium contents. Austenitic chrome-nickel steels may thus have a resistance to these acids equal to that of nickel-chromium alloys. In nitric acid and in unaerated sulfurous acid rather sharp limits of attack occur which are principally dependent on chromium content. In the former the limit of attack is not related to a particular chromium content but varies continuously with acid concentration. The action of sulfurous acid on these alloys is highly dependent on the presence of small amounts of other substances in solution, and many sulfurous acid mixtures rapidly attack alloys to which the pure acid is wholly inert. The observed effects are not compatible with Tammann's theory relating corrosion resistance to lattice structure but are believed to be concordant with current views of the electrochemical nature of corrosion. Introduction The discovery, development and engineering application of iron alloys resistant to corrosion may well claim a place among the important developments in metallurgy of the past two decades. The varied demands of industry coupled with the skill of the metallurgist have resulted in the production of an extensive group of steels and alloys ranging from the now familiar "stainless " chromium steels of the kitchen to special alloys of great chemical complexity for particular, exacting needs. Any adequate description of the important properties of these-— physical, chemical and economic—would be a formidable undertaking.

Jan 1, 1929

By Donald E. Ackerman, Norman B. Pilling

The solubilities of a series of experimental alloys covering the range 0 to 100 per cent. Ni, 0 to 30 per cent. Cr have been studied under conditions of complete submersion in several fully aerated acid solutions, and in solutions containing sulfurous acid. In nonoxidizing, hydrogen-discharging acids, if the nickel content is below a certain critical amount, chromium increases the rate of solution and nickel decreases this rate; this critical content of nickel is about 13 per cent. Alloys containing more than this corrode at a constant minimum rate independent of iron, nickel or chromium contents. Austenitic chrome-nickel steels may thus have a resistance to these acids equal to that of nickel-chromium alloys. In nitric acid and in unaerated sulfurous acid rather sharp limits of attack occur which are principally dependent on chromium content. In the former the limit of attack is not related to a particular chromium content but varies continuously with acid concentration. The action of sulfurous acid on these alloys is highly dependent on the presence of small amounts of other substances in solution, and many sulfurous acid mixtures rapidly attack alloys to which the pure acid is wholly inert. The observed effects are not compatible with Tammann's theory relating corrosion resistance to lattice structure but are believed to be concordant with current views of the electrochemical nature of corrosion. Introduction The discovery, development and engineering application of iron alloys resistant to corrosion may well claim a place among the important developments in metallurgy of the past two decades. The varied demands of industry coupled with the skill of the metallurgist have resulted in the production of an extensive group of steels and alloys ranging from the now familiar "stainless " chromium steels of the kitchen to special alloys of great chemical complexity for particular, exacting needs. Any adequate description of the important properties of these-— physical, chemical and economic—would be a formidable undertaking.

Jan 1, 1929

Last November, when the British Educational Mission was visiting this country, letters were sent to the various mining schools asking what arrangements had been made for cooperating with British and. French schools. Of the eleven schools from which replies were received, none had taken any definite steps in this direction. The Colorado School of Mines, though, stated that it was offering scholarships to all men who had served in the U. S. Army and Navy during the war. A letter was also sent to Sir Henry Miers, Vice-chancellor of the University of Manchester, who was the head of the British Mission. He replied as follows: "In my opinion the mining profession is second to none in the responsibility of the duties which it involves or to which it leads in all parts of the world; also it is a. profession in which the student or teacher has much to gain by migrating to foreign countries. This applies in a special degree to British students coming to America where they will be able to enlarge their views by a widened experience. We (the Mission) have everywhere found the most, cordial acceptance of such proposals. Several of the British Universities have recently instituted a new doctorate of philosophy attainable after 2 or 3 years course of advanced study; this scheme includes Oxford and Manchester. The conditions admitting to the degree course are that the applicant should be a graduate of an approved University and should show evidence that he is qualified to pursue the course which lie proposes." In a conversation with Prof. Alfred C. Lane, of Tufts College, Sir Henry Miers said that students from Great Britain should be most easily attracted to America, both to universities and colleges and technological institutions.. He doubts, however, whether Great Britain can offer America, in this respect, as much as America can offer her. Prof. Lane, though, is quite sure that, especially for geologists, there is much to be

Jan 2, 1919

By P. B. Liebermann

The resistance to motion offered by mine cars is caused principally by: Rolling friction, flange friction, bending rails, bearing friction and wind resistance. With proper construction and with a fair amount of attention and care, that is, under favorable conditions, the first three items cannot be greatly improved. The wind resistance ordinarily is negligible on account of the slow speeds commonly used. The bearing friction, however, is a variable item, depending upon the design, the bearing material, the lubrication, the location (whether in wheel-hub or on car-body) and the alignment. Under the most favorable conditions the bearing friction will reach a lowest possible value. By the development of a successful anti-friction mine-car bearing this lowest value has been improved to such an extent as to affect the whole system of mine haulage. After being satisfied of their durability and certainty of operation, any investigation into the advantages of anti-friction bearings for mine cars will have to be based upon reliable information as to the saving in power of such bearings. While numerous tests have been made in this direction, the results have not always been convincing, principally because of the rather crude methods that were employed. These crude methods are the main cause of the wide variations existing in regard to the exact amount of the frictional resistance. Frequently an ordinary spring balance is used and the pull necessary to move a certain car or train of cars is obtained by a number of readings. Such spring balances necessarily have a coarse graduation and the continuous vibration and fluctuations to which they are subjected make them highly dependent upon the individual observer. Further, they must be frequently calibrated. Sometimes these tests were made without regard to acceleration, speed or even grade. The method of using an electric locomotive as a testing device is perhaps more open to criticism than the spring-balance method, because it introduces additional sources of error: The varying electrical and mechanical losses in the locomotive. Also, such a measurement always includes the power necessary to move the locomotive itself. This means a considerable amount of figuring, and the results due to the various multiplications and corrections may be of little value, for obvious reasons. When figuring the drawbar pull from the electrical

Jan 1, 1917

By M. S. Azun

M.S. Azun I have many objections to the content of the author's paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV's) such as semivariogram function ?(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [1 N-hy*(h) = 2(N h) i21 {Xi-Xi+h}Z, h=0, 1, N-1] where N is the total number of samples, Xi is the sample value at the i - th location, X i+h is the sample value at the i +h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2,…., up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author's paper, one can employ any fitting techniques, such as curve fitting, or any ar¬bitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author's practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV's. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV's. There are a lot of problems for modeling of onedimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. ? References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity. ?

Jan 1, 1986

By Philip Henry

THERE is a difference of opinion among engineers on the subject of depreciation in general, and still more on its application to any given case. The committee which was appointed by the American Society of Civil Engineers to make a report on Valuation of Public Utilities, states "There is no subject connected with valuation about which there are more diverse views than those relating to depreciation;" and in the discussion which took place upon the presentation of the preliminary report of this committee in January, 1914, that part of the report dealing with depreciation called forth more discussion than any other. From this discussion it was evident that the word " depreciation" was not always used in the same sense, so it is quite important that some definition be adopted. As this paper relates to the proper method of treating depreciation by corporations or individuals operating oil properties, both of which must make a return of annual net income to the government in connection with the income tax, it will be in order to adopt the definition of the Internal Revenue Bureau. Under date of Mar. 29, 1910, the Commissioner of Internal Revenue of the Treasury Department stated "Deduction on account of depreciation of property must be based on lifetime of property, its cost, value and use." Again, on Form 1035, "Return of Annual Net Income" for miscellaneous corporations (Section 2, Act of Congress approved Oct. 3, 1913), a deduction from gross income is allowed for "Total amount of depreciation for the year." This item is defined more particularly as follows: "The amount claimed under Item No. 5 (b) for depreciation should be such an amount as measures the loss which the corporation actually sustains during the year in the value of buildings, machinery, and such other property as is subject to depreciation on account of wear and tear, exhaustion, or obsolescence. The amount taken credit for on this account in order to be allowable should be so entered on the books as to constitute a liability against the assets of the corporation. The amount claimed under this item should not cover losses in the value of stocks and bonds. Decrease in the book value of securities owned, so far as such decrease represents a decline in the actual value of such securities, should be deducted under item 5 (a) of the return.

Jan 1, 1915

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous metals of certain classes recovered in the United States for the year 1924 to 1925 as shown in Table 1. The figures are tabulated simply to give the reader some idea of the scope of the secondary non-ferrous metal industry. Approximately 900,000 tons of an annual value of $244,000,000 were recovered in the year cited. In 1916 (again using the Mineral Resources of the United States as authority) the tonnage reclaimed was approximately 632,000 tons and the value, because of the high prices for metals prevailing at that time, amounted to $265,000,000. It is not the purpose of this paper to discuss smelting and refining operations or the feasibility of an organization, primarily engaged in some other activity, conducting smelting and refining operations to convert its own non-ferrous scrap metals and alloys. The classification and preparation of these non-ferrous materials is a preliminary step, regardless of what subsequent operations the material may pass through or where these operations may be conducted. For that reason the subject can be readily discussed without any reference to subsequent activities. Space must be provided, with suitable handling facilities, scales and the necessary storage bins where the material may be accumulated. The scope of the activity, the nature of the industry and the tonnage handled will determine, in a large measure, what preparation, if any, it may be desirable to give these scrap materials to put them in the best marketable condition. By preparation is meant largely what, for the want of a

Jan 1, 1928

By H. F. Seifert

The classification and preparation of non-ferrous scrap mctals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accurnulates in such manufacture scrap from these materials for disposition in the form of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition of such scrap is left to indivitluals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost whicli with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous metals of certain classes recovered in the United States for the year 1924 to 1925 as shown in Table 1. The figures are tabulated simply to give the reader some idea of the scope of the secondary non-ferrous metal industry. Approximately 900,000 tons of an annual value of $244,000,000 were recovered in the year cited. In 1916 (again using thc Mineral Resources of the United States as authority) the tonnage reclaimed was approximately 632,000 tons and the value, because of the high prices for metals prevailing at that time, amounted to $265,000,000. It is not the purpose of this paper to discuss smelting and refining operations or the feasibility of an organization, primarily engaged in some other activity, conducting smelting and refining operations to convert its own non-ferrous scrap metals and alloys. The classification and preparation of these non-ferrous materials is a preliminary step, regardless of what subsequent operations the material may pass through or where these operations may be conducted. For that reason the subject can he readily discussed without any reference to subsequent activities. Space must be provided, with suitable handling facilities, scales and the necessary storage bins where the material may be accumulated. The scope of the activity, the nature of the industry and the tonnage handled will determine, in a large measure, what preparation, if any, it rrlay he desirable to give these scrap materials to put them in the best niarketable condition. By preparation is rneant largely what, for the want of a

By L. B. Beneitone

Over the years, the rope changing procedure on the two double-drum San Manuel ore hoists has been streamlined and improved, so that a job that once required eight hours to complete is now finished in four. The ropes, constructed of improved plow steel, 6 x 25 filler wire, pre-formed, right lay, Lang lay with a fiber core and weighing 8 ½ lb per ft, have a 2 ¼ in. diam and are 3200 ft long. They have widely varying lives, but on the average a rope change on one of the two hoists is required every six months. When a rope change becomes necessary, the ropes on both drums of a hoist are replaced. Thorough planning and preparation are essential for efficient rope changes. A briefing session is held on the day prior to the change, during which the entire procedure is reviewed on a blackboard and discussed among the cable rigging crew. These discussions have led to many improvements that have been incorporated into the present rope changing procedure.

Jan 4, 1968

By Arthur G. Metcalfe

Arthur G. Metcalfe (SOLAR)—Three explanations to account for mechanical nucleation effects are considered in the paper, viz., theories based on fragmentation, agglomeration, and pressure-wave mechanisms. The authors show that none of these mechanisms will explain the results observed with tin and Sn-Pb alloys. A fourth mechanism of nucleation enhancement was developed during work at Armour Research Foundation on casting of beryllium and, although presented briefly on various occasions, the theory has never been discussed adequately. It is believed that this theory will explain many of the observations. Classical homogeneous nucleation theories assume that embryo nuclei are formed in the melt as a result of compositional and/or thermal fluctuations. Stable nuclei are formed when a critical size is reached such that the decrease in free energy for conversion of this volume of melt to solid offsets the increase of surface, energy. The assumption is made that the average properties of liquid and solid metal can be used. In practice this assumption is invalid and indeed is contrary to the postulation of thermal and compositional fluctuations in the melt. Actually the conditions favoring embryo formation bring the seeds of its own destruction—the thermal and compositional fluctuations leave the embryo surrounded by atoms of higher thermal energies and/or by solute atoms that depress the melting point. Any mechanical method of dispersing this destructive

Jan 1, 1964

By Morris M. Fine, Norwood B. Melcher

As a raw material, prereduced pellets can be considered symptomatic of the quiet revolution taking place in the quality and grade of blast furnace burdens for the past decade. In 1954, the average analysis of ores from U.S. ranges in the Great Lakes area was 50.86% Fe (natural), 10.22% SiO2, and 10.90% moisture; ten years later, the average was 56.67% Fe (natural), 8.13% SiO2, and 6.17% moisture. The advance in Canada was even more pronounced in a lesser number of years. In 1957 the average product of Canadian ore-producing areas was 51.62% Fe (natural), 8.59% Si02, and 8.02% moisture; in 1964, the average grade was 59.59% Fe (natural), 6.27% SiO2, and 3.94% moisture.2 These dramatic data are testimony to the giant strides made in iron ore improvement, and the next logical step is prereduction. Prereduction can well be considered as a beneficiation step in which oxygen is the gangue. Since the ultimate objective of milling and smelting is iron metal, non-metallic constitutents in general, whether oxygen or silica, are contaminants. The past and continuing attack aimed at lowering the silica content of concentrates is succeeding. One need only thumb through the Grade Name listings of the American Iron Ore AssociationVo note that virtually all commercial pellets contain less than 8% silica, many are lower than 6%, and a few below 45%. With natural technical evolution, it is expected "many" rather than "few" will ultimately be in the last category and further mechanical concentration will have reached the point of diminishing returns. At this level, oxygen would constitute the only major diluent worthy of attack.

Jan 7, 1966

By B. T. Brady

Rock mechanics, like all engineering disciplines, must have a theoretical foundation. The subject of this chapter is the formulation of analytical methods that may aid in the rational design and determination of the stability of engineering structures in competent brittle rock materials. By an engineering structure in rock, we mean any (1) excavated sub- surface opening, (2) open surface structure, or (3) system of openings in rock that is virtually self-supporting-that is, not requiring artificial systems to carry structural stresses.

Jan 1, 1970

By Herbert D. Drechsler

The objective of this paper is to identify the components of income above that necessary to keep a mine in production and relate those components to the profits of a mining firm. This is a discussion of "Economic Rent". Economic rent is the payment to the factors of production -- capital, labour, entreprenuer and the owner of the mineral deposit -- above the minimum necessary to keep all of these factors cooperating in the production of minerals from a particular deposit. THE SOURCE OF ECONOMIC RENT IN THE MINING INDUSTRY In the mining business each mine has a unique cost of production unrelated to any other mine. The cost of production is developed from many factors such as the technical characteristics of the deposit: depth of deposit, depth of overburden, areal extent, and type of deposit. Furthermore, there are locational factors which also alter cost of production. For example, identical mineral deposits located in Zambia or in the southwest U.S.A. would have different capital and operating costs. These differences occur because of different qualities of labour, ease of acquisition of operating supplies or investment capital and other similar factors. To explain the source of rent, we shall use ideas developed by Alfred Marshall and Kenneth Boulding. Suppose a meteorite with special qualities exploded over earth and sent showers of small meteorites to the ground in various places. At some point in time, people learned of the special qualities of these meteorites and a demand arose and one mine was started. Suppose further that the cost of production to produce these meteorites was different for each deposit. Probably the lowest unit cost mine would commence production because if a higher unit cost mine started-up, eventually someone would discover a deposit that had a lower unit cost of production. The lower unit cost mine would take over the market and the high unit cost mine would cease production. The cost curve for the first mine would look like the following Figure 1. [ ] The output for the first mine is on the horizontal axis with the cost per ton on the vertical axis. The curve labelled AC I is the average total cost of production over the range of possible production that could occur at the property. The total costs are composed of variable costs, which are dependent on output and fixed costs, which are dependent on time. For example, the cost of operating supplies would be a variable cost and normal profit would be a fixed cost.1 The opportunity cost of the investment would also be part of the fixed costs. In our example, all factors of production, are receiving the minimum necessary payment that will keep the mine operating. The average total cost curve is U-shaped because at zero output, the meteorite mine has no variable costs, only fixed costs which, on a unit basis, obviously are very high. To produce a small output of meteorites, the mining firm adds

Jan 1, 1985

By Meng-Cherng Sun, Fun-Den Wang, David M. Ropchan

A proposed technique for improving coal-mine roof stability by softening parts of coal pillars along the sides of entries developed from structural analysis is presented. This technique is based on the transference of the high stress concentration in the roof near the upper corners of a rectangular opening to the roof rock and coal over the solid away from the opening. This transferral is accomplished by softening parts of the coal pillars by drilling a series of parallel holes into the coal in the ribs and face of the entry prior to advance. The effectiveness of the pillar softening in terms of reducing the opening width (so that the stress in the roof near the corner is equivalent to that of a narrower opening) ranges from 3 to 5 ft for a 16-ft entry using a series of 4 to 5-ft-deep parallel drill holes of 3 to 6-in.-diam on a 1 to 2-ft spacing for a particular geology. Pillar softening should be highly effective in controlling roof where cutter-roof cave conditions exist, because this technique reduces the high stress concentration in the roof at the upper corners of the opening. It may also be effective for reducing tensile roof failure and coal rib sloughing for certain specific geological conditions. This technique appears to be a simple, effective, and practical method that can be used to supplement conventional roof support methods of roof bolting, timbering, roof truss, and other existing methods in underground coal mines. The authors consider the technique feasible and believe that it merits underground trials.

Jan 1, 1975