Search Documents

By Louis C. McCabe

The control of dusts and fumes of submicron size is involved in many process industries. This paper presents in tabular form the quantitative data from a number of metallurgical operations and discusses allowable discharge in terms of effluent-weight ratio. Typical installations for recovery of stack effluents are cited. THERE are many sources of smoke, fumes, gases, and dusts that may cause undesirable contamination in an industrial area. Fumes and gases are the result of chemical action or volatilization, while dusts are produced in processes of disintegration and dispersion. Commonly, smokes are suspended particles formed by combustion or destructive distillation. Methods for controlling smoke are generally known, and great improvements have been made in equipment for removing fine dusts and fumes from gases. In most of the industrial centers of the country, the chief duty of the air-pollution abatement agency is the elimination or reduction of emissions resulting from improper combustion. Correct methods of firing, proper fuel selection, and installation of properly designed equipment may accomplish this. It is becoming more widely recognized that much of the contamination of an industrial atmosphere is caused by dusts, fumes, and gases that are not related to the process of combustion. As such emissions are usually a functional part of plant operation, they rarely can be prevented even by better design and careful operation. When dusts, fumes, and gases are an integral part of the operation, mechanical equipment must be designed to remove these emissions. Most of the dusts and fumes that should be controlled are less than 1 micron in size. Control of such small particles is largely a new and untried field in many industrial areas. However, where conditions have been critical, effective control equipment for dusts, fumes, and gases has been in operation for many years. The problem is not one of smoke abatement and requires an entirely different set of standards for effective solution. Identical standards need not be applied to all industrial areas because of differences in meteorology, physiography, plant location, plant density, and nature of stack effluents. In this paper, discussion of control of atmospheric contamination by industrial plants refers specifically to the Los Angeles area, but the method of approach is applicable to any area where similar problems are encountered. Quantities of particulate matter reported in analysis of stack effluents indicate the need for standards of emission. Many types of dusts and fumes that contribute materially to the air-pollution problem are discharged into the atmosphere at a lower rate than 0.40 grain per cu ft at standard conditions. On the other hand, some stacks discharge at a higher

Jan 1, 1951

By Blamey Stevens

The object of this paper is to present a theory of the formation of fissures, which seems to be supported by all available data. The investigation is, in the main, an exact one, and irregularities of the rock-structure are generalized. From the conclusions drawn a general classification of fissures is made, and this should be of practical use in the comparison of mineral deposits. The theory also throws some light on the equilibrium of the earth's crust and the depth of action of surface-waters. Incidentally, additions are made to the theory of earthquake-slips. Former Theory. It has been previously pointed out that the "jointing" of homogeneous rocks occurs in two sets of planes, at right angles to one another, and making angles of 450 with the directions of greatest and least principal stress.' The theory by which this fact is explained does not, however, account for fissures and faults, because normal faults are usually more vertically, and reverse faults more horizontally, inclined than 450. The "jointing law" is based on the following axiom: In a homogeneous mass under pressure, rupture must take place on the lines of maximum tangential stress."2 This law applies, with fair approximation, to the tests on jointing which can be made in the laboratory, and as nearly as can be expected to the natural jointing-planes in rock-masses, where the stresses are not very great; but it entirely fails to account for fissure-fractures.3

Jan 1, 1910

By J. L. Thompson

Lime made in a coal-fired rotary kiln has two distinct parts: the interior of the pebble which constitutes about 90% to 95% of the mass, and the surface dust layer which is the remaining 5% to 10%. Uncalcined carbonate and impurities in the product may be present and will not contribute to the hydration reaction. Sulfur, in the form of calcium sulfate, inhibits the hydration reaction out of all proportion to its actual weigh- percent concentration (perhaps more than 100 times). If the stone contains dolomite, this will also inhibit the reaction as its rate of hydration may be nearly three orders of magnitude slower than that of calcium oxide. Early in the hydration reaction dolomite appears practically intert, but given sufficient time, it will hydrate. The heat of reaction is nearly the same as for calcium oxide, but the time necessary for complete hydration may be hours; whereas for calcium oxide it is only fractions of a second. The dust layer on the surface also inhibits hydration as it contains a collection of compounds which have low heats of hydration. This layer can tie up additional calcium and delay or prevent its reaction. In addition to these chemical processes, an important physical characteristic of the lime is its specific surface area. This is effected by the thermodynamics of calcination and the original stone grain chemistry. All of these factors are agglomerated in the gross slaking rate of lime.

Jan 1, 1980

By Marion Rice

The copper-mining district of Jerome, Ariz., is of such economic importance that the following brief notes may be of interest. The ore deposits are said by Ransome1 to be pre-Cambrian, and are contained in the pre-Cambrian schists of the region. In the vicinity of the mine (the United Verde) the schist stands nearly vertical and strikes a little west of north. At least three varieties are distinguishable—(1) a green rock, schistose on its margins but grading into massive material, which is evidently an altered dioritic intrusive; (2) a rough gray schist with abundant pheno-crysts of quartz, apparently an altered rhyolite; and (3) a satiny, greenish gray, very fissile sericitic schist that may be a metamorphosed sediment. The ore occurs in varieties (2) and (3), the main belt of dioritic rock (1) lying just west of the orebodies. The ore is said to follow as a rule the layers of fine sericitic schist. T. A. Rickard2 Says that the ore at the United Verde Extension mine is found at the contact of diorite and schist, that both diorite and ore are earlier than the regional metamorphism, and that the quartz porphyry ("rhyolite" of Ransome) is of post-Cambrian age. The material considered here, a part of which was gathered by the writer, came from four of the mines of the district, and its study was undertaken at the suggestion of Dr. Berkey of Columbia University. The field relations and exact locations of the different specimens are not known, but a microscopic study of the thin sections gave some evidence as to the origin of the ore, which will be discussed below. The indications are that both ore and porphyry were introduced at the closing stages of the metamorphism, this being in accord with Ransome's view of the genetic relation of porphyry and ore rather than with the opinion that the ore is related to the diorite. Certain field occurrences mentioned in the literature also support this theory. Rickard, in the same article to which reference has been made, speaks of a vein of chalcocite several inches wide at the contact of one of the porphyry dikes, and Provot,3 although he regards the porphyry as subsequent to the ore, says: "Acid dikes encountered underground should be followed as they have been found in practice to lead to orebodies."

Jan 1, 1920

By G. R. Rubly, H. J. Steele

LOCATION AND HISTORY THE San Manuel property is in townships 8S and 9S, range 16E, Gila and Salt River Base and Meridan, State of Arizona. This area is in the Old Hat mining district, southern Pinal County, and is about 3;2 miles southwest of the town of Mammoth on the San Pedro River and one mile south of the Mammoth mine at Tiger, Arizona. The property consists of over 150 contiguous lode claims. The Old Hat district was prospected prior to the Civil War, but there was little or no production until 1881.1 The chief producers have been the Mammoth and Mohawk mines, now consolidated and operating as the St. Anthony Mining and Development Co., Ltd. Production to 1936 was $5,200,000, of which 83 pet was gold.2 Since 1940 the production has been chiefly lead and zinc, and some molybdenum and vanadium. There are a few small properties in the vicinity that have produced very minor tonnages of copper ore. In the San Manuel group there are claims which have been held continuously from 1906 to the present time, and at least two churn-drill holes were put down on or near the outcrop in 1917. No logs for these holes are available, but it is assumed that the grade of copper encountered was not sufficient to encourage further exploration. A small amount of ore has been shipped from open cuts on the San Manuel outcrop area, but there is no record of the tonnage or grade. It is estimated that not more than 5o tons were mined. These cuts, plus a few shallow shafts and some short adits indicate limited and unenthusiastic prospecting at San Manuel. In 1942, through the efforts of James M. Douglas, R. B. Giffin, Victor Erickson, and Henry W. Nichols, owners of the San Manuel group, the Reconstruction Finance Corporation and War Production Board authorized the United States Geological Survey to investigate the property, and by their recommendation, the United States Bureau of Mines was authorized to put down a limited number of churn-drill holes. The Bureau of Mines carried on drilling from November 1943 to February 1945. Seventeen holes were drilled, varying from 305 to 1990 ft in depth. The property was brought to the attention of Magma Copper Co. in June I944 and an option agreement was made with the owners. Subsequently, a group of claims lying north of the original group and held by the Apex Lead Vanadium Mining Corp., and a group to the east held by the Quarelli family, were optioned. A drilling program was laid out to conform to the Bureau of Mines pattern, and drilling started in December 1944. San Manuel Copper Corp. was incorporated September 1945, and has carried on the exploration program to the present time. GEOLOGY General The mineralized outcrop, chief copper mineral of which is chrysocolla, is a tri-

Jan 1, 1947

By G. R. Rubly, H. J. Steele

The San Manuel property is in town&ips 8S and 9S, range 16E, Gila and salt River Base and Meridan, State of Arizona. This area is in the Old Hat mining district, southern pinal county, and is about 31/25 miles southwest of the town of Mammoth on the San Pedro River And one mile south of the Mammoth mine at Tiger, Arizona, The property consists of over 150 contiguous lode claims. The old Hat district was prospected prior to the civil war, but there was little or no production until 1881.1 The chief producers have been the Mammoth and Mohawk mines, now consolidated and operating as the st. Anthony Mining and Development Co., Ltd. Production to 1936 was $5,200,000, of which 83 pet was gold.2 Since 1940 the production has been chiefly lead and zinc, and some molybdenum and vanadium. There are a few small properties in the vicinity that have produced very minor tonnages of copper ore. In the San Manuel group there are claims which have been held continuously from 1906 to the present time, and at least two churn-drill holes were put down on or near the outcrop in 1917. No logs for these holes are available, but it is assumed that the grade of copper encountered was not sufficient to encourage further exploration. A small amount of ore has been shipped from open cuts on the San Manuel outcrop area, but there is no record of the tonnage Or grade. It is estimated that not more than 50 tons were mined. These cuts, plus a few shallow shafts and some short adits indicate limited and unenthusiastic prospecting at San Manuel. In 1942, through the efforts of James M. Douglas, R. B. Giffin, Victor Erickson, and Henry W. Nichols, owners of the Sari Manuel group, the Reconstruction Finance Corporation and War Production Board authorized the United States Geological Survey to investigate the property, and by their recommendation, the United States Bureau of Mines was authorized to put down a limited number of churn-drill holes. The Bureau of Mines carried On drilling from November 1943 to February 1945 Seventeen holes were drilled, varying from 305 to 1990 ft in depth. The property was brought to the attention of Magma Copper Co. in June 1944, and an option agreement was made with the Owners. Subsequently, a group of claims lying north of the original group and held by the Apex Lead Vanadium Mining Corp, and a group to the east held by the Quarelli family, were optioned. A drilling program was laid out to conform to the Bureau of Mines pattern, and drilling started in December 1944 Sari Manue1 Copper Corp. was incorporated September 1945, and has carried on the exploration program to the present time. Geology General The mineralized outcrop, chief copper mineral of which is chrysocolla, is a tri-

Jan 1, 1949

By G. R. Rubly, H. J. Steele

The San Manuel property is in town&ips 8S and 9S, range 16E, Gila and salt River Base and Meridan, State of Arizona. This area is in the Old Hat mining district, southern pinal county, and is about 31/25 miles southwest of the town of Mammoth on the San Pedro River And one mile south of the Mammoth mine at Tiger, Arizona, The property consists of over 150 contiguous lode claims. The old Hat district was prospected prior to the civil war, but there was little or no production until 1881.1 The chief producers have been the Mammoth and Mohawk mines, now consolidated and operating as the st. Anthony Mining and Development Co., Ltd. Production to 1936 was $5,200,000, of which 83 pet was gold.2 Since 1940 the production has been chiefly lead and zinc, and some molybdenum and vanadium. There are a few small properties in the vicinity that have produced very minor tonnages of copper ore. In the San Manuel group there are claims which have been held continuously from 1906 to the present time, and at least two churn-drill holes were put down on or near the outcrop in 1917. No logs for these holes are available, but it is assumed that the grade of copper encountered was not sufficient to encourage further exploration. A small amount of ore has been shipped from open cuts on the San Manuel outcrop area, but there is no record of the tonnage Or grade. It is estimated that not more than 50 tons were mined. These cuts, plus a few shallow shafts and some short adits indicate limited and unenthusiastic prospecting at San Manuel. In 1942, through the efforts of James M. Douglas, R. B. Giffin, Victor Erickson, and Henry W. Nichols, owners of the Sari Manuel group, the Reconstruction Finance Corporation and War Production Board authorized the United States Geological Survey to investigate the property, and by their recommendation, the United States Bureau of Mines was authorized to put down a limited number of churn-drill holes. The Bureau of Mines carried On drilling from November 1943 to February 1945 Seventeen holes were drilled, varying from 305 to 1990 ft in depth. The property was brought to the attention of Magma Copper Co. in June 1944, and an option agreement was made with the Owners. Subsequently, a group of claims lying north of the original group and held by the Apex Lead Vanadium Mining Corp, and a group to the east held by the Quarelli family, were optioned. A drilling program was laid out to conform to the Bureau of Mines pattern, and drilling started in December 1944 Sari Manue1 Copper Corp. was incorporated September 1945, and has carried on the exploration program to the present time. Geology General The mineralized outcrop, chief copper mineral of which is chrysocolla, is a tri-

Jan 1, 1949

By J. H. Wiggins

This paper first pictures the economic phase of evaporation losses and the actual evaporative conditions in handling and storing crude and gasoline in the United States; then follows a discussion of some of the theories of physics involved in evaporation loss and lastly an application of these theories to handling oil and gas on producing properties. GRANTING that about 600,000,000 bbl. of light oil will be produced in the United States this year and taking the Bureau of Mines' statement that 7 1/2 per cent. of the total crude production will be lost before the finished gasoline is shipped from the refinery, the volumetric evaporation will be 45,000,000 bbl. of the cream of the gasoline. This is a conservative figure and is equivalent to 1,890,000,000 gal. The real value of this liquid is at least 150 per cent. of the value of an equal volume of motor fuel. At only 10 c. per gal., the value lost is $189,000,000; at 15 c. per gal. the loss is $283,000,000. If 750,000,000 bbl. of light and heavy oil are produced here this year and the average price per barrel is $1.333, the gross return to producers will be $1,000,000,000 and the net returns about $200,000,000, if the cost of production is only $1 per barrel. Thus, the evaporation bill is about 20 per cent. of the gross income and is equal to the net income of the crude-oil producers. Two other comparisons with popular phases of the petroleum industry will help give an adequate conception of the evaporation problem. These are: cost of preventing evaporation compared to cost of cracked gasoline and volume of gasoline evaporated compared to volume of gasoline manufactured from natural gas.

Jan 7, 1924

By E. H. Bunce, H. M. Haslam

The "direct process" for the manufacture of pigment zinc oxide produces the oxide directly from ore. This is accomplished by reducing the zinc by means of carbonaceous fuels and immediately burning the evolved zinc vapor to zinc oxide. For many years this was done by smelting a loose charge of ore and fuel on perforated grates. Since this process was developed in America and was extensively used here, it has become known as the "American process." Alternative methods of producing pigment zinc oxide are the "indirect process " and the "wet process." In the indirect process the raw material is metallic zinc, which is volatilized and burned to the oxide. For a long time this has been done in externally fired horizontal refractory retorts. This process has become known as the "French process," from the country of its origin. The wet process precipitates the carbonate or hydrate from zinc-bearing liquors and then calcines the precipitate. This method has been but sparingly used for producing commercial quantities of zinc oxide. It appears to be advisable to restrict the use of the terms "American process" and "French process" to the methods of the earlier periods and to consider the terms "direct process" and "indirect process" as generic terms to designate, first, all methods of producing pigment zinc oxide directly from ores, and, second, to include all those methods of producing zinc oxide from metallic zinc and metallic zinc-bearing substances. American Process In 1796 John Atkinson was granted British Patent No. 2094/1796 entitled, "Manufacture of White Paint." This patent describes a method of producing zinc oxide in which roasted zinc blende or calcined calamine is mixed with charcoal, and the mixture heated in a muffle to liberate zinc vapor, which is then burned to obtain zinc oxide fume. About 1850 The New Jersey Zinc Co., at its plant in Newark, N. J., attempted to make zinc oxide by smelting, in a reverberatory furnace, a mixture of coal and ore from its Franklin mine. A considerable amount

Jan 1, 1937

By Alexander L. Holley

THE Pernot system of rotating and withdrawing the hearth of a Siemens regenerative gas furnace for the production of Martin or open-hearth steel, is, perhaps, the most conspicuous of the several improvements which have lately been made in the steel manufacture. These several improvements in the open-hearth plant are not combined in any existing works, but most of them will be combined in not less than three works now erecting in the United States; and it seems probable that their joint result will not only reduce the cost of products of ordinary grades to Bessemer rates, but that it will produce new and better grades of products. The open-hearth steel furnace and its operation are so generally understood that but a few words of general description are necessary. The ordinary furnace is not unlike the common reverberatory puddling furnace, except that an intense, uniform, and controllable temperature is maintained by the Siemens gas regenerative system. The materials. employed are various : melted or unmelted pig with ore, and with or without scrap; pig iron purified from silicon and phosphorus, with or without scrap; pig iron and scrap, melted together in a cupola, or charged hot or cold, together or separately, into the steel furnace; a pig-iron bath, and hot or cold steel or iron scrap, direct sponge or Catalan or puddled blooms charged into the bath. The operation is, to a greater or less extent, according to the nature of the materials used, a desiliconization and decarburization of the pig or other crude iron, and its dilution by already purified materials. Manganese is employed at the end of the operation to remove oxide of iron and silica, a regulated amount of manganese remaining in the product. Figs. 2 and 3, Plate IV, represent the hearth and roof of the Pernot furnace; Fig. 1 shows, in cross section, the general arrangeent of open-hearth plant with Pernot furnaces, as generally designed by the author, and now building at two works. The engrav-

Jan 1, 1879

By Kenyon E. Richard, James H. Courtright

Thomas W. Mitcham (Strategic Minerals, Inc., Grand Junction, Colo.)—The authors have presented a significant contribution to the field of mining geology. The article is graphic, remarkably concise, and crisply original. The presentation is made on only three pages with two maps, but their Silver Bell story is entirely adequate in background, development, and conclusion. Most of their colleagues would agree that this paper reflects the high quality of the work which these unusually capable men have done in the Silver Bell area over the past few years. The Silver Bell area is one of complex tectonic structure, and time and spatial relationships are by no means apparent. Actually, most of the observations and interpretations in this paper are new to published geologic literature on the Silver Bell area. I am in agreement with these interpretations with two possible exceptions, which are discussed below. One might well define the three roughly parallel west-northwest faults, shown on the insert of Fig. 2, as the major structural elements of the area. North to south, I propose that these be named the Ragged Mountain fault, the Silver Bell fault zone, and the Waterman thrust, after the mountain ranges which are the results of these major structures. While I would agree with the authors that the northern two of these major structures are high-angle faults of the Laramide revolution, my impression is that the southern structure is a low-angle thrust of approximately Miocene age. In support of this opinion, I submit the following observations: 1) irregularity of the fault in strike; 2) scarcity of Laramide intrusives and alteration of sediments along the fault; 3) present high re- lief of the Waterman Range which indicates youth or certainly rejuvenation; and 4) existence of a series of parallel structures farther to the south which results in an outcrop pattern suggesting imbricate thrusting. The authors have stated that Laramide igneous activity began with the intrusion of alaskite. Some dacite flows appear to be conformable with Cretaceous beds, and thus my impression was that alaskite followed the intrusion and extrusion of dacite. I would be interested to learn of evidence in support of the reverse relationship suggested by the authors. Kenyon Richard and J. H. Courtright (authors' reply)—The authors appreciate Mr. Mitcham's attention to this paper. The names he proposed for the major faults seem appropriate. His suggestion that the Waterman fault is a thrust may be correct because he did more work in that particular area than the authors. However, it is believed that no direct evidence of a low-angle thrust relationship has been recognized, and the authors consider that indirect evidence favors a high-angle fault interpretation. The pre-dacite flow age of the alaskite is definitely established, the authors believe, by the fact that the flows rest on an erosion surface which was carved in the dacite porphyry, an intrusive clearly younger than the alaskite, as evidenced by inclusions of alaskite occurring in dacite porphyry. No direct evidence of Cretaceous sediment-flow rock relationships was found at Silver Bell, but in the nearby Tucson mountains dacite agglomerates, megascopically similar to those at Silver Bell, overlie a basal conglomerate which in turn rests on the truncated edges of steep-dipping Cretaceous arkosic beds.

Jan 1, 1956

By O&apos, R. G. Meara, B. W. Gandrud

In 1034 the Southern Experiment Station of the U.S. Bureau of Mines in cooperation with the University of Alabama began an investigation of the availability of kyanite ores as a source of raw material for the manufacture of refractories. Under this program, gravity concentration and flotation tests have been made on two varieties of Georgia kyariite ore, mica schist and massive. Most of the attention has been directed to the mica schist ores, as they are more widely distributed and seem to offer greater economic possibilities than the massive ores. It is evident that the preparation of kyanite for use as a refractory material involves other considerations than the mere elimination of impurities. A concentration process that eliminates impurities satisfactorily may have to be followed by some additional treatment, since the final product must be of a coarseness and size ratio that will make it suitable for refractories manufacture. So far in the investigation at the Southern Experiment Station of the U.S. Bureau of Mines only the concentration problem has been considered, and this paper is intended as an interim report. Ores The schist ores contain 1 to 9 per cent of kyanite crystals embedded in mica and quartz, with smaller amounts of graphite, garnet and iron oxide and minor amounts of other heavy minerals. The garnet content varies from a trace to a few per cent. The minerals are easily released by moderate grinding. The size of the kyanite ranges from fine needles to crystals 1 1/2 in. long, 1/2 in. wide and 1/4 in. thick. The garnet, quartz and iron oxide grains have a smaller mean mesh than most of the kyanite. The maximum size of the garnet crystals corresponds to about 14 mesh and that of the sand grains is considerably less. Most of the iron oxide is still finer, for the minus 100-mesh size is greatly enriched in Fe²O3. The massive ore consists of radiating masses of kyanite interlocked with quartz, mica, corundum and small amounts of other heavy minerals.

Jan 1, 1938

By B. W. Gandrud, R. G. Meara, O&apos

In 1034 the Southern Experiment Station of the U.S. Bureau of Mines in cooperation with the University of Alabama began an investigation of the availability of kyanite ores as a source of raw material for the manufacture of refractories. Under this program, gravity concentration and flotation tests have been made on two varieties of Georgia kyariite ore, mica schist and massive. Most of the attention has been directed to the mica schist ores, as they are more widely distributed and seem to offer greater economic possibilities than the massive ores. It is evident that the preparation of kyanite for use as a refractory material involves other considerations than the mere elimination of impurities. A concentration process that eliminates impurities satisfactorily may have to be followed by some additional treatment, since the final product must be of a coarseness and size ratio that will make it suitable for refractories manufacture. So far in the investigation at the Southern Experiment Station of the U.S. Bureau of Mines only the concentration problem has been considered, and this paper is intended as an interim report. Ores The schist ores contain 1 to 9 per cent of kyanite crystals embedded in mica and quartz, with smaller amounts of graphite, garnet and iron oxide and minor amounts of other heavy minerals. The garnet content varies from a trace to a few per cent. The minerals are easily released by moderate grinding. The size of the kyanite ranges from fine needles to crystals 1 1/2 in. long, 1/2 in. wide and 1/4 in. thick. The garnet, quartz and iron oxide grains have a smaller mean mesh than most of the kyanite. The maximum size of the garnet crystals corresponds to about 14 mesh and that of the sand grains is considerably less. Most of the iron oxide is still finer, for the minus 100-mesh size is greatly enriched in Fe²O3. The massive ore consists of radiating masses of kyanite interlocked with quartz, mica, corundum and small amounts of other heavy minerals.

Jan 1, 1938

By R. V. Colligan

[CONTENTS PACE Educating and Training Economic Geologists of the Future. By C. H. BEHRE, JR. (TP 2278, Min. Tech., Nov. 1948. Discussions by R. V. COLLIGAN and EVAN JUST) ....... I Mercury Industry in Italy. By EDWIN B. ECKEL. (TP 2292, Min. Tech., Jan. 1948. Discussion .............................. by C. N. SCHUETTE) 3 Chert in the Kingsport Formation at Mascot, Tennessee. By ARTHUR T. ALLEN. (TP 2299, ............... Min. Tech., Jan. 1948. Discussion by M. M. BUTLER) 5 Wall Rock Alteration at Butte, Montana. By RENO H. SALES and CHARLES MEYER. (TP 2400, Min. Tech., May 1948. Djscussions by C. D. HULIN, W. D. JOHNSTON, JR., and L. C. ................................... GRATON) 5] Educating and Training Economic Geologists of the Future R. V. COLLIGAN*-I can best illustrate my opinions by drafting another five year plan (Table 2). This plan is set up following the same stipulations outlined by Dr. Behre, namely: (I) the student is preparing himself for commercial work as a mining geologist; (2) he is attending an institution with a sufficiently broad curriculum (that is, engineering school and mining school as well as liberal arts college) to furnish the courses listed; and (3) he is not planning to continue his studies through to a doctor's degree before going into commercial work. A comparison of my study plan (Table 2) and that submitted by Dr. Behre (Table I) will at once point up the basic similarity, due to the obvious fact that there are so many essential courses which must be included in any outline of study. However, a more detailed analysis will show up certain differences, which, in fact, are only certain refinements on Dr. Behre's program. These I plan to discuss in order of their importance. The first and most important change is the addition of 12 hr of optional subjects, making a total of 24 hr of optional subjects as against a total of 12 hr under Dr. Behre's schedule. This of course entails the elimination of certain courses, which I shall discuss later. However, I wish to make it clear that I suggest eliminating these courses not because I feel that they are unnecessary, but rather because I feel the optional courses are more necessary to the complete education of the individual. I appreciate that Dr. Behre recognizes the importance of the cultural side of education, but I take issue with his thesis that the student will get it without credit and in his spare time. I do not think that the average college student, and certainly not the college freshman, is mature enough to know what he needs and where to get it in his spare time. I think it must be "spoon-fed"; he must be oriented through specific courses. University life (or should I say "college life") is too full of athletics, fraternity activities, dances, "bull sessions," and countless other enjoyable distractions, all of which contribute to the "full man." I fail to see how the average young American male can possibly sandwich in a necessary complement of "cultural activities" in his spare time. Since these latter activities do not fall within the pattern set by the "group," and show less promise of immediate return in enjoyment, or increased social status on the campus, they are bound to suffer in competition with the more popular, "group" activities. No doubt much of the criticism levelled against arts colleges, namely, that the cultural courses are useless, is well taken, for the culture

Jan 1, 1947

By William R. Rumbold

WHEN I was in South Africa during the latter part of 1904, there were three known tin-fields, which may be called the Cape Town, the Bushveld and the Swaziland fields. THE. CAPE TOWN TIN-FIELD. This district is situated near Kuils river, 20 miles west of Cape Town, and 5 miles from Kuils River station on the Cape Town & Stellenbosch Railway. The deposits are in granite, intrusive in the Malmesbury beds, which are supposed to be of Silurian or Cambrian age. The granite, resisting denudation better than the surrounding shales,, has formed low-lying hills, the highest of which, the Bottlelary Berg, is 1,510 ft. above sea-level. , The rock consists of quartz, orthoclase feldspar and biotite mica; tourmaline is also present. The feldspar occurs in large crystals. The rock is generally decomposed on the surface, and the decomposition sometimes extends as deep as 100 ft. This formation-granite intrusive in Silurian shales-extends for many miles to the northeast, but so far as I know the Kuils River deposits are the only ones now known to occur in it, though probably further prospecting will reveal other deposits. This particular discovery was accidental;. alluvial tin being found in the course of boring for oil. The Kuils River Deposit. This comprises both lode and alluvial tin. The lode strikes N. and S., and dips about 30° E. into the hill. It is 5 ft. wide, and composed of dense white quartz, in which pinkish-gray cassiterite is distributed in large crystals. The vein also contains considerable quantities of wolfram. Fig. 1 is a rough plan of the relative positions of the lode and the alluvial deposit, the latter, as shown, following the course of a stream, while the lode crops out on the hillside

Jan 7, 1908

By F. L. Robertson, C. H. Bacon, J. W. Till

A description is given of the development of a process for making low sulphur steel on furnaces fired with 2 1/2 pet sulphur oil. Slag and metal are analyzed at melt. Slag weight is estimated. A simple method for calculating necessary lime additions for making 0.025 and 0.035 pct sulphur steel is given. DURING the last 15 years John Summers & Sons have been confronted increasingly by the problem of producing a low sulphur steel from high sulphur materials. The principles adopted, the processes used, the data collected on a furnace specially set aside to study this problem, and speculation on future developments are dealt with in this paper. This study is limited to two melting shops which make sheet steel only, of the following analysis: C, 0.06 pct; Mn, 0.33; S, 0.04, 0.035, 0.03, and 0.025; and P, 0.02 and 0.015. All the processes described have reference to the manufacturing of this steel and are not necessarily applicable, without modification, to other steels. The raw materials used are given in Table I. Development of Process About 1934, Schenck's work on phosphorus was applied to frame quantitative rules for the removal of phosphorus, with great success. We could however, neither in our own work nor in the voluminous literature, find any assistance to frame quantitative furnace rules to remove sulphur. Perhaps, we should have persevered with Schenck's outstanding chapter on sulphur in The Physical Chemistry of Steelmaking, but we missed the importance of one (Ss) sentence on p. 478. "Evidently this ratio -------- is [S] the important quantity to be considered from the point of view of chemical reaction; it is clear that the sulphur content of the steel alone, as frequently given in the literature cannot suffice for judging the success of the reaction unless special details are given regarding the sulphur charge and the amount of slag."' We were not however very successful in getting values for Schenck's "n" that agreed with (S) arrived at by our direct analysis. [S] In addition to Schenck's work much attention was given to V value. The formula selected for V was: (SCaO) — 1.57 (2 P2O5) (S SiO2) After plotting many charges a curve was obtained, based upon the relationship between the percentage sulphur in the finished steel and V value, Fig. 1. For a long time this was used as standard with about a 60 to 70 pct success on producer-gas fired furnaces, if all uprising scrap was used and no bought scrap used. An inspection of this curve shows clearly that it is not a quantitative manufacturing process, and that it was not sure enough to go to the trouble and expense of doing stage analysis for P,O,,

Jan 1, 1952

By D. E. Etter, J. E. Selle

The Pu-Ce phase diagram was determined by differential thermal analysis, metallography, and elechm-nricroprobe analysis. The dingram is chararterized by a eutectic with extensive solid solubility in the cubic Phases of both cerium and plutonium. No intermediate phases were found. Cerium is soluble in e plutonium to 16.0 at. pet Ce at 626OC nnd in d plcltoniurn to 23.0 at. pet at 613 "C, decreasing to 17.5 at. pet at room temperature. No solubility in the a, ß, or ? phases was jound, and the mininum cerium required to stabilize 5 plutonium to room temperature is 3.2 at. pet. The maximum solubility of plutonium in 6 cerium is 19.5 at. pet at 721OC, and the maximum soluhility of plutonium in ? cerium is 34.5 at. pet. Invariant points in the system are: a) eutectic at 626oC, L16.5 = E Pu16.0 + y Ce65.5; b) peritectoid at613oC, e Pu13.5 -y Ce65.5- d Pu23.0. AS part of a program aimed at the determination of the phase equilibria in the Pu-Ce-Cu ternary system, preliminary investigations were made of the three binary systems. A survey of the Pu-Ce binary system by differential therma1 analysis indi- cated several areas of disagreement with the published diagram,' primarily in the shape of the liquidus surface. Consequently, a thorough investigation of the system was undertaken, and this report presents the results of the study. EXPERIMENTAL PROCEDURE Three methods of investigation were used: differential thermal analysis (DTA), metallography, and analysis with electron-microprobe X-ray analyzer (EMX). The EMX analysis was particularly useful for the determination of solvus lines. The DTA method was most useful for the determination of the liquidus curves. Metallography complemented both of these techniques. Materials. The cerium metal used for most of this work had a freezing point of 805°C. This material showed 15°C premelting, and was found metallographically to contain some unidentified in~lusions.2 The temperature of premelting is defined as the point at which the DTA curve breaks away from the base line, analogous to a curve obtained from a solid-solution alloy. Several compositions were prepared near the cerium end of the diagram with higher-purity material which had a freezing point of 800°C. etallographic analysis showed this material to be relatively free of inclusions and only 8°C premelting was observed. Major impurities were found by spectrographic

Jan 1, 1964

By Paul Billingsley

The Georgetown mining district is located in Deerlodge county, Mont., about 20 miles west of Anaconda. It lies along the divide between the headwaters of Warm Springs creek, draining eastward, and Flint creek, flowing west and north through the Philipsburg valley. The actual divide is formed by Cable mountain, a narrow ridge running north and south, terminating to the south in low hills overlooking Georgetown lake, and to the north in a high, rugged plateau that falls off to the west to the wide valley of Flint creek. On the eastern, or Warm Springs, slope of Cable mountain is the Cable mine, with the Hidden Lake mine a few miles north. On the western slope is the Southern Cross group, with smaller mines, the Twilight, Cincinnati, Red Lion, and Big Bill, at intervals to the northward. The Georgetown mines lie in the hills south of Cable mountain; the Philipsburg mines, of which the Granite Mountain, Bimetallic, Hope, and Trout are the chief, form a separate group to the north, overlooking Flint Creek valley and Philipsburg. (See Fig. 1.) The region ranges in elevation from 5,000 to 9,000 ft. It is, with the exception of the lower valleys, well timbered with small fir and pine, although Cable mountain and the higher summits to the northward rise slightly above timber line. The main valleys have the smooth contours of glaciation, and their mouths are frequently choked with morainal deposits. General Geology. In a very general way the valley of Flint creek coincides in this region with the boundary between the pre-Cambrian slates of western Montana and the folded Palaeozoic rocks of the Rocky Mountain system. The great limestone formations of the Carboniferous and Devonian, lying at flat dips, extend from Anaconda well toward the head of Warm Springs creek, but on the divide the Cambrian appears, closely folded and intruded

Jan 1, 1914

To the members of the A. I. M. E., who have given much and risked all to fight "Over There" with pick, or gun, or brain, and to the members who have chosen the sometimes more self-denying duty of remaining at home to help produce metals for fighters: Your experience in foreign lands has bred in you that spirit of internationalism which will soon be infused into every corner of our country by virile lads thrilling from a great experience in an old, yet new, land over the seas. To them the East will not seem as far from the West as it was, nor the North from the South. Sectional jealousies will seen despicable to one who has fought for a great ideal shoulder to shoulder with real men of other nations. And they who have willingly sacrificed much on the altar of service will have little patience with an egotist, be he laborer, tradesman, capitalist or engineer. The problems which peace brings to us are more difficult than those of war and their solution requires not only cool heads, tolerance, and wise judgment, but the "getting together" of sections and classes and individuals. The triumph of justice over individualism, represented by the draft law, must be repeated, for there are "slackers" in peace Is well as in war, and the spirit of self-denial expressed in response to Liberty Loans, Red Cross, and Welfare drives and Food Administration appeals must live. We have only just begun to learn how to serve. It is often claimed by our members that the engineer is not given, in the community at large, the recognition which his training should merit; that his reward is not as great nor his service as welcome as it should be. Public service is generally assumed to be a logical activity for a lawyer,

Jan 12, 1918

By H. E. Lee, P. C. Feddersen

Blast-fuRnace operation at the Bunker Hill smelter deviates somewhat from common practice. Under existing conditions it is economical to operate the furnaces at "forced" capacity. The furnace feed consists chiefly of sinter and averages close to 50 per cent lead. Experience in smelting such material favors a low charge column attended by smaller proportions of coke and a low blast pressure. Under such conditions the gain in furnace tonnage greatly overbalances the somewhat higher slag losses and increased percentage of material fumed Furnace Charge The ingredients for the blast-furnace feed are stored in a group of 24 charge bins (3600 cu. ft. capacity). Each bin has two discharge chutes. Beneath each chute is a steel weighing hopper, suspended from a Fairbanks scale. The several hoppers are kept filled with the exact amount of material required to complete a furnace charge. The weighed material is discharged into a standard-gauge, bottom-dump charge car containing two compartments, each of which holds a complete charge (approximately 1½ tons). It is hauled to the blast furnace by a 44011 electric trolley locomotive. The proportionate parts of the various constituents of a representative blast-furnace charge are shown in Table 1. Table 1.—Representative Blast-furnace Charge at Bunker Hill Smelter Material Pounds Sinter.................................................. 2500 Limerock............................................... 0- 50 Coke................................................. 250-300 Scrap iron.............................................. 0-25 Settler skulls.......................................... 75 Undried zinc-plant residue................................ 0-200 Siliceous ore............................................ 25 Baghouse dust.......................................... 0-50 By-product slag......................................... 100 A variable stock tonnage of zinc-plant residue and return by-products results in fluctuations in the percentages of these materials in the blastfurnace feed. Accompanying such variations are corresponding increases or decreases in the amounts of coke, limerock and scrap iron necessary to obtain good furnace operation and adequate reduction.

Jan 1, 1937