Search Documents

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig' 1. I' In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By John T. Eash

DURING the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin, 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. SELECTION OF COMPOSITION While the final criterion of the suitability of an alloy for a bearing must 0f course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstructure, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig. I. In addition, the tin bronze contains the hard alpha + delta eutectoid constituent distributed through-

Jan 1, 1945

By T. B. Brooks

THE iron ores of the Marquette region are mostly extracted in open excavations; hence the process is more properly quarrying. Several attempts at underground work have been made, which have not, on the whole, been successful. The Edwards mine has been almost entirely wrought by candle-light. The slate ore pit, NO. 1, of the New England mine, is now worked in the same way, as is also the Pioneer furnace pit of the Jackson mine. The Champion mine was opened systematically for underground work, with two levels, 60 feet apart, and three shafts at distances apart along the bed of 200 feet; but this idea has been practically abandoned, the greater part of the ore in that mine being now taken out in open pits. Several other mines have occasionally worked underground stopes, but only temporarily; if such stopes could not be opened out to daylight, they have usually been abandoned. In brief, it may be said that no considerable amount of ore has as yet (1870) .been extracted underground in the region, and of that so mined very little has been taken out at a profit; and I may add that it seems to be the belief of the most experienced mining men that this state of things will hold for some time to come for reasons which will appear. Nearly the same remarks may be applied to the mines of the Iron Mountain region, Missouri, the ores of which are very similar in character to those of Marquette. Some of the New York and New Jersey magnetic deposits are wrought open, but this is the exception, underground mining there being the rule. The following brief sketch of the geological structure of the Marquette deposits will indicate some advantages of the method of mining employed. The iron-bearing (Huronian) series of rocks, are stratified beds, the principal ore formation being overlaid by a quartzite, and underlaid by a diorite, or greenstone. This ore formation is made up, first, of pure ore; second, of "mixed ore" (i. e., banded

By John Garcia

THE presence of carbon de terre along the banks of the Illinois river was noted by the members of the Joliet and Marquette expeditions in 1673, and that may be referred to as the birthday of coal in the Middle West. The march of progress in the majority of indus-tries radiating from Chicago-one of the phenomena of history-is due in no small measure to this same carbon de terre and to the development and exploita-tion of the vast coal resources, which nature in a generous mood spread so lavishly over almost the en-tire state. The geological records indicate that coal-bearing rocks underlie three-quarters of Illinois, in-cluding 85 of the 102 counties and the entire area is estimated at from 36,000 to 42,000 square miles. Not all of the coal in this great area may be mined under the conditions existing today; producers are now taking the "cream" since industry demands the best quality and the lowest cost, thereby forcing competition among operators, which, in turn, com-pels the development of mines in those areas where the coal may be most readily .won, leaving the coal that is more difficult and expensive to mine to pos-terity. This is not such a bad arrangement, since the engineers of succeeding generations will enjoy the advantage of the experience of their ancestors, where-by they should profit and know how to mine a 2-ft. seam with as much economy and dispatch as we today work coal of thrice that thickness. During the period between 1830 and 1850, Illinois coal-mining progressed from the art of scratching along the outcrop to the development of small mines, mostly slopes, drifts and shallow shafts, but the real progress in the industry was coincident with the con-struction of railroads.

Jan 2, 1927

By Samuel Hoyt

THIS paper gives a brief description of an investigation made several years ago on the diffusion of zinc into copper. The material for that study was furnished in the form of thin copper strips coated with zinc. The result was required rather quickly and at not too great an expense, and especially information was desired as to the rate at which zinc would diffuse from the zinc coating into the copper and the temperature at which the operation should be carried out. A study of the requirements of this problem indicated that the solution might be secured by means of six determinations. This is the smallest number that will give the information desired and, at the same time, furnish checks on the accuracy of the determinations which justify an abbreviated experimental program. This does not count a preliminary test which was designed to give some idea of the correct temperature to use. The minimum number of temperatures that can be used is two. Knowing the rates of diffusion of zinc into copper at two properly chosen temperatures, it is possible to calculate the rate for any other temperature, and also to check the accuracy of the determination by means of the heat of diffusion, which is calculated from the effect of temperature on the rate of diffusion. The minimum number of determinations at any one temperature is three. The amount of diffusion which occurs at a fixed temperature is definitely related to the time of diffusion, so that by determining the amount of diffusion for three different time intervals, this relationship may be established and possibly a check on the accuracy may be secured. This accounts for the six determinations or experiments, and suggests the logical plan of the work. The check used here is not generally applicable to diffusion phenomena, but it seems to hold closely enough for the limited amount of diffusion in this investigation to justify its use.

Jan 1, 1928

By William E. Ford, Edward Salisbury Dana

I. Oxides of Silicon. 11. Oxides of the Semi-Metals : Tellurium, Arsenic, Antimony, Bismuth ; also Molybdenum, Tungsten. III. Oxides of the Metals. The Fifth Class, that of the OXIDES, is subdivided into three sections, according to the positive element present. The oxides of the non-metal silicon are placed by themselves, but it will be noted that the compounds of the related element titanium are included with those of the metals proper. This last is made necessary by the fact that in one of its forms TiOz is isomorphous with MnOp and PbOz. A series of oxygen compounds which are properly to be viewed as salts, e.g., the species of the Spinel Group and a few others, are for convenience also included in this class.

Jan 1, 1922

By C. D. King

THE advances in basic open-hearth practice which have occurred during the past decade, have been principally in the direction of the physical development of larger units, decreased fuel consumption and increased length of furnace campaigns. However gratifying the economies which have resulted from these improvements are, it must be granted that like advances in chemical, physical-chemical and metallurgical knowledge pertaining to open-hearth practice would have added greatly to these already attained reductions in costs and it is the purpose of this paper to stimulate the discussion and study of these phases of cooperation and their relation to ingot yields. DEFINITION AND CALCULATION OF LOSSES In discussing basic open-hearth yields, the writer refers to the ingot yields obtained in the process of converting pig iron, scrap and ore to steel. In this conversion some scrap is produced. The difference between the total weight of ingots and scrap produced and the original metallic charge, constitutes the loss. Basic open-hearth yields vary considerably, and while some of the divergencies can be explained metal-lurgically because of differences in slag analysis, proportion of pig charges, and character of steel made, there often remain differences that apparently do not readily disclose themselves. In reconciling yields by the usual accepted methods of calculation, one is often forced to evaluate large losses as "unaccounted for." Such a system is prone to accept these large losses as inherent to the operation and not susceptible of appraisement and correction. It is obvious that if the ingot yield, plus the scrap recovered subtracted from 100 per cent. determines the loss, a drop in yield may increase the loss or the scrap, and both contribute to a monetary loss. To be sure, one can subdivide these unaccounted for losses into various components, such as metallics in slag, free Fe in slag, spillage, etc., and thereby reduce the amount of losses considered as "unaccounted for." If empirical methods could indicate with some degree of accuracy all losses, however slight, the undetermined losses become appreciably smaller and resultant calculations will check actual

Jan 1, 1929

By Wolfgang O. Gluschke

INTRODUCTION Virtually all countries have general legislation covering most aspects of mining and mineral processing, including investment and tax laws, safety and health regulation, and specific rules applying to exploration reporting procedures. Yet most developing countries negotiate individual agreements with foreign investors for major mineral projects, in particular when all or part of the expected output is exported. Such agreements are known under several different names, as for example concession agreement; technical assistance agreement or service contract; management agreement; production sharing contract; joint venture; or contract of work. The objectives and conditions governing such contracts are as diverse as these titles are. While a mining project is only one among a large mumber of similar undertakings in industrial countries, in most developing countries such projects usually have a dominating position within the country's economy. The general legislation is often inadequate and insufficiently detailed to cover all aspects of large projects with extensive foreign inputs and international markets. Therefore, the need for specific arrangements. Specific arrangements may also become necessary due to the complexity of markets for mineral products, the large number of participants - equity partners, suppliers, financial institutions, buyers, etc. - or economic and political conditions in the host country and fiscal regulations in the home country of the investors. Most agreements are concluded between governments, or government agencies, in developing countries and private industry headquartered in developed market economies - Canada and the United States of America in North America, Western European countries, Japan, South Africa and Australia - or, in some instances, with state-owned firms in these countries. There are fewer agreements between developing countries and the centrally planned economy countries - Eastern Europe and the USSR - which cannot be considered here because of absence of adequate information. Agreements can be concluded at any of the different stages from exploration through closing of a mine. While most contracts are negotiated at the time when a potentially viable ore body has been delineated and investigated sufficiently to anticipate a realistic time for commencement of production, other agreements start with "grass-roots" exploration, during operation of a mine, smelter or refinery or, exceptionally, after a temporary shutdown. While several major provisions are included in all types of agreements, others are covered in much more detail (or not at all) in some contracts reflecting the specific work programme of each project. While it is realized that subdivision and classification of complex contractual relations is necessarily arbitrary to a certain extent, such grouping is useful in practical terms, especially for the non-specialist. The following discussion, therefore, will start with a description of the major forms of contractual relation - concession, investment contract, joint venture, management agreement, service and production sharing contracts. Major issues covered in all, or almost all, agreements will then be dealt with. These include stages of development, corporate structure and control, fiscal arrangements, infrastructure development and environmental law, and dispute settlement and renegotiation. FORMS OF CONTRACT RELATIONS There has been marked change in the type of agreement entered into during the 1960s (and before) and the early 1970s and the period thereafter. While straight "concessions" - granting of exclusive rights to foreign investors over a certain deposit or areas with little restriction or well-defined obligations - were the rule during the first half of this century, more complex agreements have evolved since. Some of these cover every conceivable aspect, foreseen or only possible, and define rights and obligations of all partners to the last detail. Over the years, agreements have without doubt become more beneficial for the developing host countries, in part as a result of well-publicized nationalizations, as for example in Chile, and in part due to changed attitudes in all countries

Jan 1, 1985

By W. W. Anderson

WEBSTER'S dictionary gives the following definition for "efficiency": "Effective operation as measured by a comparison of actual and possible results." Engineers think of this definition in terms of the ratio of output to input, and since they learn early in their careers that output cannot be greater than input, they usually consider a machine to be 100 pct efficient if it operates perfectly, and to be 0 pct efficient if it performs no function at all. Hence, values of efficiency between 0 and 100 pct reflect how well or how poorly a machine has performed; and any method of calculation for determining efficiency that does not show 0 pct when no function has been performed, and 100 pct when a perfect job has been done, is looked upon with skepticism. The literature on performance of coal cleaning equipment contains many references to efficiency of performance, but there is no unanimous agreement among the authors as to how the efficiency should be determined. Numerous methods of calculation have been proposed from time to time, most of which attempt to fulfill the definition of efficiency by comparing output to input, using float and sink data or some other characteristic, such as dry ash content, as a measure. However, to the best of our knowledge, none of the methods advocated in the past meets the requirements of a practical engineer in judging cleaning plant performance, because the formulas previously advocated do not confine numerical values of efficiency between 0 and 100 pct, and the literature does not contain an explanation of the meaning of the formulas under various conditions of operation. Therefore, the following formula, based on Yancey's concept of misplaced material,' is proposed as a measure of efficiency which will conform with the requirement that the values of efficiency must be confined between 0 and 100 pct: Quantitative Efficiency = 100.0 — (pct wt sink* in cleaned coal + pct wt float* in refuse)t • At gravity of separation effected by cleaning equipment. t Total product basis of the size of material under study. It will be noted from this formula that an actual separation between cleaned coal and refuse must be effected by the cleaning equipment before the formula can be used; also, that improperly distributed material in the products must be determined at the gravity of separation, rather than at some arbitrary test gravity. It will further be noted from this formula that the weight of cleaned coal recovered and the weight of refuse rejected by the equipment have their proper influence, because the sink in the cleaned coal and the float in the refuse are expressed in the equation as a per cent weight of the total products of a definite size discharged from the plant. This formula has one other important characteristic, in that it requires no knowledge of the feed to the cleaning unit. Comparison of data on the products from a cleaning unit with the feed to the unit can lead to many worthwhile conclusions. but not in regard to the efficiency of separation effected by the equipment. The reason for this is that mechanical fracture of many pieces of the feed occurs during the cleaning process; and in some processes crushers are deliberately incorporated in the flow to produce size degradation to free impurities from cleaned coal, thereby altering the washability characteristics of the material while in process. When such size degradation occurs in a cleaning process, it is quite possible that this crushing will result in a reduction in ash content in the finer sizes of cleaned coal when compared with the raw coal feed, even though no true separation has been effected. This is due to the fact that the finer sizes have been "sweetened" by the crushing of cleaned coal from some coarser size. Many formulas advocated in the past show high cleaning efficiencies

Jan 1, 1951

By W. W. Anderson

WEBSTER'S dictionary gives the following definition for "efficiency": "Effective operation as measured by a comparison of actual and possible results." Engineers think of this definition in terms of the ratio of output to input, and since they learn early in their careers that output cannot be greater than input, they usually consider a machine to be 100 pct efficient if it operates perfectly, and to be 0 pct efficient if it performs no function at all. Hence, values of efficiency between 0 and 100 pct reflect how well or how poorly a machine has performed; and any method of calculation for determining efficiency that does not show 0 pct when no function has been performed, and 100 pct when a perfect job has been done, is looked upon with skepticism. The literature on performance of coal cleaning equipment contains many references to efficiency of performance, but there is no unanimous agreement among the authors as to how the efficiency should be determined. Numerous methods of calculation have been proposed from time to time, most of which attempt to fulfill the definition of efficiency by comparing output to input, using float and sink data or some other characteristic, such as dry ash content, as a measure. However, to the best of our knowledge, none of the methods advocated in the past meets the requirements of a practical engineer in judging cleaning plant performance, because the formulas previously advocated do not confine numerical values of efficiency between 0 and 100 pct, and the literature does not contain an explanation of the meaning of the formulas under various conditions of operation. Therefore, the following formula, based on Yancey's concept of misplaced material,' is proposed as a measure of efficiency which will conform with the requirement that the values of efficiency must be confined between 0 and 100 pct: Quantitative Efficiency = 100.0 — (pct wt sink* in cleaned coal + pct wt float* in refuse)t • At gravity of separation effected by cleaning equipment. t Total product basis of the size of material under study. It will be noted from this formula that an actual separation between cleaned coal and refuse must be effected by the cleaning equipment before the formula can be used; also, that improperly distributed material in the products must be determined at the gravity of separation, rather than at some arbitrary test gravity. It will further be noted from this formula that the weight of cleaned coal recovered and the weight of refuse rejected by the equipment have their proper influence, because the sink in the cleaned coal and the float in the refuse are expressed in the equation as a per cent weight of the total products of a definite size discharged from the plant. This formula has one other important characteristic, in that it requires no knowledge of the feed to the cleaning unit. Comparison of data on the products from a cleaning unit with the feed to the unit can lead to many worthwhile conclusions. but not in regard to the efficiency of separation effected by the equipment. The reason for this is that mechanical fracture of many pieces of the feed occurs during the cleaning process; and in some processes crushers are deliberately incorporated in the flow to produce size degradation to free impurities from cleaned coal, thereby altering the washability characteristics of the material while in process. When such size degradation occurs in a cleaning process, it is quite possible that this crushing will result in a reduction in ash content in the finer sizes of cleaned coal when compared with the raw coal feed, even though no true separation has been effected. This is due to the fact that the finer sizes have been "sweetened" by the crushing of cleaned coal from some coarser size. Many formulas advocated in the past show high cleaning efficiencies

Jan 1, 1951

By Ellis H. Gates

BENEFICIATION of the manganese oxide ores at Three Kids Mine near Henderson, Nev., has evolved over a period of years. Commercial application of the process is on a secure basis, and an effective working hypothesis has been formulated to help solve the problems encountered in flotation. An outstanding difference between the Manganese Inc. operation and other flotation processes is the necessity for high recovery of slime mineral values. Part of the manganese minerals in the Three Kids ore deposit occurs as primary slime or as minerals that are easily slimed by grinding. High recovery of this slime portion is essential to an economic over- all manganese recovery. The aim of much of the research at Manganese Inc. was to recover these slimed and finely ground minerals by flotation.

Jan 12, 1957

THIS chapter and the one following deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the simplification of the first two ' laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the "heat balance" of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced, and we assume that the cause lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities of flow distribution, air leakage, etc., present in any real, open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained- by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot-metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million B.t.u. per net ton. of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million B.t.u., and the sensible heat in the preheated air at the port ends is 117 million B.t.u. so that the total heat input at the ports is 477 million B.t.u. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million B.t.u., but 120 million of this is supplied by the heat in the hot metal and by various heat--evolving reactions in the bath, so that only 75 million B.t.u. need be supplied to the bath by the flame.

Jan 1, 1944

By F. V. Lenel, G. S. Ansell, M. J. Salkind

An experiment is described in which the growth of interparticle necks in an array of loose spherical silver powder at temperatures near 300°C was determined by measuring changes in the electrical resistance of the array. The activation energy for neck growth of contacts was derived by abruptly changing temperature and noting the change in the rate of neck growth. Since the experiments were run under an external load, the changes in activation energy with stress could he determined. The activation energy was found to decrease rapidly with increasing stress. It is concluded that the material transport in the experiments is one of plastic flow by dislocation motion. The variation of activation energy with stress is typical for cross slip of dislocations, an important material transport mechanism in the temperature range investigated. THE process in which powder compacts or aggregates of loose powder are held at an elevated temperature under an external load is called hot pressing or sintering under pressure by powder metallurgists. In this investigation the early stages of this process as applied to loose spherical silver- powder aggregates were studied. The powder particles were approximately 100µ in diameter and the temperature was near 300°C, i.e., below one half of the melting point of silver in degrees Kelvin, where volume diffusion is not expected to contribute to sintering. In the process, the contact or neck areas between powder particles grow. Since this involves plastic deformation of the particles under a constant external load (even though not under constant stress) it would be termed creep by mechanical metallurgists. On the other hand, the growth in neck area observed in compacts or loose-powder aggregates held at elevated temperature without the application of an external load is termed sintering by powder metallurgists. During sintering the major driving force is the stress due to surface tension. However, even when no load is placed on the compact or powder aggregate, an external stress, i.e., gravity, plays an important role in sintering in addition to those stresses arising from surface tension, as was shown in two previous investigations.'" It is therefore postulated that no sharp dividing line can be drawn between the phenomena of "creep" and "sintering". Different material transport mechanisms may be involved in either of these phenomena, but they will depend upon the temperature and the level of stress, but not necessarily upon the nature of the driving force: surface tension or external load. At the low temperatures of this investigation, an external stress much higher than the stress due to surface tension is necessary to obtain measurable rates of neck growth. In order to avoid misunderstanding this phenomenon will be called "creep". The rate of growth in contact area in the loose silver-powder aggregates was determined by meas-

Jan 1, 1965

By R. E. Zinkham

An investigation has been conducted to compare short transverse and longitudinal fatigue and fracture properties in 4.25-in.-thick, high strength aluminum alloy plates. One plate was produced using standard rolling techniques while the other was pre.forged before rolling. Little difference was shown in fatigue strength of longitudinal specimens taken from mid-thickness of the plate. Howeuer, in the short transverse orientation fatigue strengths at 107 cycles were about 25 and 50 pct less, respectively, for the preforged and standard rolled plate. Differences in fatigue strengths were attributed to grain size and shape as well US orientation of constituents. Fatigue crack propagation rates and fracture toughness were compared at three different stress intensity (K) levels, using a constant compliance, double cantilever, wedge-shaped specimen. In a given plate, comparable fatigue crack Propagation rates were observed in the longitudinal (i9W) and short transverse (TW) orientations. Somezuhat gveater rates were observed in the short transzerse (TR) orientation. The preforged plute gave a lower rate for all three directions. Considerable secondary cracking developed, at times, over portions of the fatigue crack in both plates, particularly at the lower stress intensity levels in the short transverse specimens. Micro structure revealed constituent stringers as possible causes of the crack branching. Fracture toughness was considerably less in both plates in the short transuerse orientation. It is concluded that preforging not only improved directional tensile properties but also the fatigue and fracture properties in general. On occasion, aluminum plates have been milled away for hinges or bolted connections and stressed through the thickness or short transverse direction. Little or no information is available concerning fatigue characteristics or fracture toughness in this loading orientation in aluminum plate, or of the effect of fabrication on these properties. It was the intent of this project to examine, develop, and apply a unique specimen that has been advocated by others to study the fatigue characteristics and fracture toughness of two differently fabricated high strength aluminum plates. Linear elastic fracture mechanics criteria may be applied to the specimen so that the fatigue crack propagation rate and fracture toughness data may be of use for design or inspection applications. Fatigue characteristics are generally measured in the longtudinal or long transverse direction, where fairly large specimens such as center notched panels,' are usually employed. Limitations are evident due to plate thickness, however, in the type and size of specimen that may be tested in the short transverse direction without extensions. Therefore, a specimen that is to be loaded in this direction should, for convenience, be compact. The general type of fatigue crack propagation specimens discussed and employed herein meet this requirement. These specimens are commonly called double cantilever beam specimens and lately "crackline-loaded edge-crack specimens".2 They may vary from a slope of zero (parallel-sides) to a wedge shape, the type employed herein. In general for most specimens the stress intensity KI at the tip of a crack is a function of the load, P and crack length, a. Some varieties of the wedge shaped specimen, however, give essentially a constant stress intensity KI over a considerable range of crack length.' This feature can be a valuable asset in fatigue crack propagation experiments because the stress-intensity can be controlled simply by controlling the load without regard to crack length. MATERIAL AND METHODS Material. A standard rolled (light pass reduction) and a ~reforged and rolled (heavy pass reduction) plate of 7179-T651 material were used for the evaluation. The chemistry, processing history and average tensile properties are shown in Table I. Specimen Selection and Preparation. The specimen selected for the generation of fatigue initiation or S-N data was an axial tension type and is shown in Fig. 1. Specimens were taken from mid-thickness in the longitudinal and short transverse directions from both plates. Specimens were polished with 500 grit paper in a direction parallel to the loading axis. For the fatigue crack propagation tests, the specimen shown in Fig. 2 was used. This is similar to a specimen that has been employed by Mostovoy3 for fracture toughness studies on 7075-T6 aluminum alloy. It also fortuitiously agrees quite well with the dimensions of a specimen for which Srawley and Gross2

Jan 1, 1970

By E. T. Turkdogan, L. E. Leake

A number of measurements have been made on the vapor pressure of pure iron at 1600°C. Experiments were carried out by the transportation method in which a sample of iron is exposed in a furnace to a stream of pure argon, metered at a predetermined flow rate for a specified period of time. The vapor pressure was obtained from the weight loss of the sample. A detailed diagram of the apparatus used for the experiments is given in Fig. 1. It consisted of a horizontal molybdenum-wire-wound furnace fitted with a recrystallized alumina tube 1 1/8 in. internal diam. The boats, 1 by 3/16 by 1/8 in., were fired in argon at 1600°C to constant weight before use. After this treatment, subsequent heating of the boats to 1600°C gave little or no further change in weight, e.g. ±0.05 mg in 24 hr. The furnace and reaction tube were separately fed with argon from two independent flowmeters. These were connected to a common supply source via an argon purification furnace containing metallic titanium sponge at 700°C, and an anhydrone drying-tower. A rotary displacement-type meter was included in the gas train to provide a direct means of measuring the total volume of gas passed through the reaction tube. The material used was vacuum melted high-purity iron in the form of wire 2mm in diam. The following impurities were present in the iron: 0.008 pct C, 0.002 pct Si, 0.005 pct Mn, 0.008 pct S, 0.001 pct P, 0.01 pct Ni, 0.001 pct Cr, 0.006 pct Cu, and 0.001 pct Al. Samples consisting of three small pieces of this wire were laid end to end in a recrystallized alumina-combustion boat, and were separated by small fragments of alumina. The wire samples were then melted in argon to form spherical beads 2 to 3 mm in diam. After weighing, the boat with its contents was placed on the boat carrier and introduced into the cool end of the reaction tube. The entire furnace system was then flushed with argon for 30 min. At the end of this period, the flow of argon to both furnace and reaction tubes was adjusted to the desired level; then the boat was slid rapidly into the hot-zone of the reaction tube. After a known volume of gas had passed through the reaction tube, the boat was withdrawn quickly to the cool end of the furnace. When quite cool, the boat was removed from the fur-mace and placed in a desiccator for subsequent re-weighing. The semi-micro balance used in these experiments had a sensitivity of 0.005 mg. The above procedure was repeated at several flow rates within the range of 25 to 300 ml per min. The flow of argon in the annular space between the two tubes was at a rate of 300 ml per min in all experiments. During all the experiments the furnace temperature was maintained at 1600° ± 5°C by means of a temperature controller. The temperature of the reaction zone was measured with a Tinsley high precision disappearing filament pyrometer which was initially calibrated against a Pt-13 pct Rh/Pt thermocouple; the errors due to temperature measurements were within * 5°C. RESULTS Assuming that the iron vapor is in the monatomic state, the vapor pressure can be calculated from the weight loss of the sample and the volume of the carrier gas. The results obtained are plotted in Fig. 2 against the rate of flow of argon through the chamber containing liquid iron beads. At low flow rates, the thermal diffusion of iron gives an apparent high vapor pressure, but at high gas flow rates, the carrier gas is not saturated with the vapor, and therefore, low vapor-pressure values are obtained. This is now a well-known phenomenon. There is a distinct inflexion of the curve at about 120 to 160 ml per min rate of argon flow and the vapor pressure of iron within this

Jan 1, 1961

By W. R. Johnson, M. Hansen, John M. Parks

AS part of a research project sponsored by the Signal Corps Engineering Laboratories, which had the objective of obtaining a magnet wire of good conductivity and low temperature coefficient of resistance, a comprehensive literature survey, supplemented by experimental work, revealed that a linear relationship exists for solid-solution alloys between the electrical conductivity, K, and the temperature coefficient, a, as expressed by the equation: k = a/ß where ß is constant for the solvent metal and a - per°C. tR0 It has long been known that the electrical conductivity at a given temperature and the temperature coefficient of resistance of binary alloys are related to their constitution by the LeChatelier-Guertler rules, as illustrated by Figs. 1 and 2: Rule 1—In alloy systems consisting of a heterogeneous mixture of two phases, the electrical conductivity and temperature coefficient vary as a straight line, if the composition of the alloys is given in volume percentage, Fig. 1. Rule 2—In solid solutions, the electrical conductivity and temperature coefficient are always lower than those of the solvent metal, and usually a considerable decrease occurs with the first small percentage additions of the solute metal, Fig. 2b. If the two components form a continuous series of solid solutions, the electrical conductivity and temperature coefficient curves take the form of a U-curve, Fig. 2a. That some kind of proportionality exists between electrical conductivity and temperature coefficient of resistance is implied by the LeChatelier-Guertler rules and by study of data such as those given by Smith and Palmer,' Fig. 3. Dellinger2 in 1910 first recognized this relationship in a number of commercial copper wires, ranging in conductivity from 94 to 100.7 pct I.A.C.S. He gave the ratio of temperature coefficient to the percentage of conductivity as a constant, C = 0.003939. A year later, Lindeck observed that the linear relationship was valid for a wider range of conductivity in "various sorts of copper," and concluded that the product of resistivity and temperature coefficient was 6.78x10-5 1.5 pct. Since then, this relationship seems to have been entirely ignored. Conductivity-Temperature Coefficient Relationship If the electrical conductivity of copper solid-solution alloys with phosphorus, silicon, arsenic, antimony, aluminum, nickel, manganese, and iron is plotted against the temperature coefficient of these alloys, the diagrams in Figs. 4 and 5 are obtained. Similar data were found with copper-rich solid solutions containing magnesium, cobalt, and titanium,'" as shown in Fig. 6. In all cases, a linear relationship exists. The point representing the highest

Jan 1, 1952

By P More

US 4,132,621-In the electrowinning of aluminum, the cells are aligned in a lengthwise direction so as to lessen the harmful influence of the induced magnetic fields Each cell is supplied with current from the preceding cell both via the head arid at least one side riser The output of the cathode bars is divided into two separate groups, the upstream group supplying the head of the subsequent cell arid the downstream group supplying the side risers of the subsequent cell This produces a substantial improvement in cell efficiency arid a greater regularity P Morel, J P Dugois, arid B Langon, assigned to Aluminium Pechiney. Jan 2, 1979 12 pp. (204¬243M) Filed 1-12-78 (868,861) Priority: France, 1-19-77 (77/2,213) US 4,134,806-Cells, anodes, arid methods for use in the electrowinning of nickel, cobalt, copper, zinc, or other metals from an acid ore leach solution or the like The cell is provided with vertically immersed stationary cathodes and stationary rod anodes which are noncorrodible by the electrolyte arid are electrocatalytic to the anode reaction. The spaced parallel anode rods are connected to electric current supply bars The anode rods have an electroconductive core made of a metal alloy arid a surface coating of an oxide of platinum or a platinum group metal The ratio of active cathode surface area to active anode surface area is preferably at least 3 0. De Nora arid C Traini, assigned to Diamond Shamrock Tech¬nologies, SA Jan 16, 1979 13 pp. (204-105R) Filed 9-15-77 (833,661) Priority Italy, 1-29-73 (19738 A/73). Same British 1,434,334-5, dated May 5, 1976 US 4,135,994-In the electrowinning of aluminum at a high current efficiency, the electrolytic bath is a mixed molten salt consisting of 2-15% by weight of aluminum trichloride, 15-83% of sodium chloride, 15-70% of combined calcium chloride arid magnesium chloride but riot more than 40% of calcium chloride, arid optionally up to 10% of barium chloride Preferably, plate-shaped graphite electrodes used for both cathodes and anodes are arranged in parallel inclined relation so that the axis in the lengthwise direction makes an angle of from 10° to 45° to the horizontal. T Ishikawa arid H Ichikawa, assigned to Nippon Light Metal Co Ltd Jan 23, 1979 4 pp (204-67) Filed 11-15-77(851,632) Same British 1,550,502, dated Aug 15, 1979

Jan 1, 1980

By W. E. Crandall

The No. 4 shaft and hoist at Hecla Mining Co.'s Star mine have been in operation for seven months, and as development of new mining areas proceeds in the lower portions of the mine, the system is being depended upon more extensively for personnel and material handling requirements. The hoist plant is handling full payloads, at rated speeds, over a vertical distance of 5650 ft. One of the special features of this hoist is its precision braking control under all hoisting conditions. Tests indicate that emergency stops can be made with safe deceleration rates and minimum rope and conveyance oscillation.

Jan 1, 1971

By Frank C. Roberts

Progress in the facilities for handling mining products has been largely superinduced by the necessities of commercial economy ren dered requisite in order to meet the demand of competition. So rapid has been the depreciation in the value of mineral products, primarily due to the disproportionate increase of output over con sumption, that it may be justly claimed that mining, when considered as a commercial success, depends largely upon the ease and cheap ness by which the products are brought to the surface of the ground. In all methods of performing this operation, wire rope enters as an important factor; and the object of the present sketch will be to explain, as fully as is consistent with the space allotted, the various • adaptations of wire rope employed in placing coal and ores within the reach of our overground systems of transportation. These adaptations will be considered in the following order: I. Hoists. II. Inclined planes. a. Engine planes. b. Gravity planes. c. Aerial planes. III. Haulage. a. Tail-rope system. b. Counter-rope system. c. Endless-rope system. IV. Hoists. The term " hoist" is applied to the system whereby the mine product is elevated from the mine-level to the surface through ver-

Jan 1, 1888

By Ralph Hayden

I. INTRODUCTION. IN the wet concentration of ores there is always a certain amount of very fine material with which to contend, and which invariably carries such quantities of value that the treatment of it is worth while; commercially. This fine material usually contains that portion of the ore which hinders the separation of the mineral values: namely, the colloidal material resulting from the decomposition of certain constituents of the ore. The object of this paper is to show what efforts have been made to solve the slime problem as it occurs in the concentrator of the Washoe

Jan 8, 1913