Search Documents

By J. H. Ffolliott

ALL of the prospects that later became mines in the Ducktown district were discovered prior to 1854, and most of them were exploited before the turn of the century. It is the purpose of this paper to discuss the exploration and current development of the Boyd mine, discovered in 1853. It is in the heart of the Ducktown Basin, in the extreme southeast corner of Tennessee, and is being developed by the Tennessee Copper Co. GEOLOGY The geology of the district has been fully described in many papers. Probably the most complete description is that of Emmons and Laney.I The rocks of the district are considered to be of Lower Cambrian age and are a part of the Great Smoky formation, consisting mainly of interbedded graywacke and mica schist, in which the ore deposits occur. The ore bodies are included in an area of about 6 sq. miles, 2 miles wide and 3 miles long striking N. 45° E., and may be grouped into three general lode systems. The northeast system, including the East Tennessee, London and Burra Burra ore bodies, and the southeast group, comprising the Polk County, Mary and Calloway deposits, are all characterized by relatively high copper values. The ores of the central system, which includes the Eureka, Boyd, Old Tennessee and Cherokee ore bodies, are low in copper and high in total sulphide content. Boyd mine lies roughly halfway between the Old Tennessee and Eureka ore bodies [ ] and 2500 ft. in the hanging wall of the Burra Burra mine (Fig. 1). Elevation of the surface is about 1725 ft. above sea

Jan 1, 1942

By David Turnbull

In most reactions involving solids the transformation kinetics may be represented by the combination of two processes —those of nucleation and of growth. For example, Mehl and his coiq-orker in their studies on the transformation of austenite to pearlite in steels have been able to describe the kinetics in terms of the rates of nucleation and of growth. By micrographic examination of their specimens they determined the nucleation rate (rate of appearance of pearlite colonies) as a function of time, of percent transformation, and of temperature. They observed that after an incubation period in which no nuclei are observed, the number of nuclei appearing per unit time per unit of untransformed grain boundary area, increases at an increasng rate with time. When recrystallization rates have been interpreted in terms of rates of nucleation and growth and the rate of nucleation determined, an incubation period followed by an increasing rate of nucleation has also been reported. Among the studies in which this phenomenon has been observed are those of Kornfeld and coworkers3 on cold-drawn aluminum wire, of Anderson and Mehl4 n the recrystallization of aluminum sheet, and of Stanlcy and Meh15 on the recrystallization of silicon ferrite sheet. The existence of an incubation period during which no nuclei are observed does not appear to have been reconciled with the generally accepted Volmer-Becker theory of nucleation in condensed systems. This theory ostensibly requires the rate of appearance of nuclei to be independent of time. Volmer-Becker Theory In order to form a stable nuclcus of a new phase B in a mother phase A, the molecules or atoms of the mother phase must surmount a free energy barrier whose height is determined by the volume free energy change accompanying the transformation and the energy of the surface separating the two phases. The free energy difference between nuclei of various sizes and the molecules or atoms of the mother phase is plotted schematically in Fig I as a function of the radius of the nucleus r. This free energy difference is plotted for two values of the change of free energy per atom, (Jb — ja) accompanying the transformation when the volumes of the two phases are infinite. One of these values of (Jb—Ja) corresponds to a temperature above the temperature To at which the phascs A and B are in equilibrium, and the other to a temperature below To. In order for a nucleus of phase B to be stable at a temperature T² < TO, its radius must be equal to or greater than the critical value r* for which the free energy of formatioil of the nucleus is a maximum, the of phase B having radii equal to or less than r* will be called embryos hfehl and Jetter," in discussing the kinetics of nucleation in solid systems, suppose that embryos of critical size are formed

Jan 1, 1949

By G. Thodos, R. B. Grieves

A method has been developed For predicting the critical temperatures and critical pressures of binary mixtures of carbon dioxide, hydrogen sulfide, nitrogen, hydrogen, carbon monoxide and oxygen with the normal paraffin hydrocarbons. For carbon-dioxide and hydrogen-sulfide systems, relations are presented that take into account the peculiar behavior of mixtures with closely boiling components, such as carbon dioxide-ethane and hydrogen sulfide-propane mixtures which exhibit minimum critical temperature points. For hydrogen, nitrogen and carbon-monoxide systems, the extreme critical behavior caused by wide differences in pure component properties is established In addition, those fixed gas-paraffin systems which resemble paraffin-paraffin systems are also accounted for. For a mixture of known composition, the pure component critical temperatures, critical pressures and normal boiling points are all that are required to determine its critical point. Graphical relations are presented relating Tc and PC , of the mixture to the pure component properties. From the treatment of 12 carbon-dioxide and hydrogen-sulfide systems reported in the literature (74 mixtures), the expected error lor the critical temperature is approximately 1.5 per cent, and for the critical pressure, approximately 2 per cent. From the treatment of six hydrogen, nitrogen and carbon-monoxide systems reported in the literature (30 mixtures), the expected error for both the critical temperature and critical pressure is approximately 2.5 per cent. The relationships, which have been developed with only normal paraffins as the hydrocarbon components, may be extended to those isoparaffins and olefins which fall within the allowable volatility ranges. INTRODUCTION Many of the fixed gases — carbon dioxide, hydrogen sulfide, nitrogen, hydrogen, carbon monoxide and oxygen — occur in natural mixtures with hydrocarbons. Carbon dioxide and hydrogen sulfide are frequent components of the fluids produced from underground petroleum reservoirs. Nitrogen, carbon dioxide and hydrogen sulfide are present in varying quantities in most natural gases and gas-condensate well effluents. Hydrogen mixtures are of considerable interest in many phases of refining processes of petroleum. The determination of the critical temperatures and critical pressures of such mixtures is of value in vapor-liquid equilibrium studies, for the prediction of the characteristics of underground reservoirs, and for reduced-state correlations of PVT, transport and thermodynamic properties. The accurate estimation of the critical point for binary mixtures is an important initial step toward a complete analysis for the establishment of the critical temperatures and pressures of multi-component mixtures. Methods for predicting the critical temperatures and critical pressures of binary hydrocarbon systems have already been presented in the literature.8 It is possible to apply these existing methods to fixed gas-paraffin mixtures, but due to their unusual critical behavior, values calculated deviate considerably from experimental values. For systems containing trace quantities of the fixed gases, these methods are acceptable; however, for systems containing more than 5 mol per cent of the fixed gases, these utterly fail to produce reasonable critical values. Consequently, in this study a method has been developed for handling such binary mixtures over the entire composition range. CARBON-DIOXIDE AND HYDROGEN-SULFIDE SYSTEMS The critical behavior and the vapor pressure behavior of mixtures of carbon dioxide and hydrogen sulfide with paraffinic hydrocarbons may be quite similar or quite dissimilar to that of paraffin-paraffin mixtures, depending on the volatilities of the components involved. The critical temperature and normal boiling point of carbon dioxide are very close to the corresponding values for ethane, while its critical pressure is considerably higher than that of ethane. The normal boiling point of

By Reynold Q. Shotts

CHEMICAL methods, based on the relative rates of oxidation of fusain, bright coal, and dull coal by nitric acid, have been devised to determine these coal components.1-4 Results obtained by oxidation methods for fusain have been checked against results obtained from microscopic methods5, 6on duplicate samples of the same coals, but to the author&apos;s knowledge this has not been done for bright and dull coal components. For this reason it is not certain that the two methods of analysis identify essentially the same chemical or physical units. It would be highly desirable to see results of the application of both methods to duplicate samples, but in the absence of any such data the author has attacked the problem indirectly. From the U. S. Bureau of Mines samples were obtained of three Alabama coals which the USBM had analyzed optically and reported on over the past 30 years. These samples were subjected to analyses by oxidation rate methods. Results of this work, and comparisons with the USBM analyses, have been published." This was the first indirect approach to the problem. The present report attempts a second indirect approach by way of internal validation. By nitric oxidation samples of two whole coals were carefully analyzed for fusain, bright coal, and dull coal. One coal was analyzed in duplicate. Duplicate portions of each of the coals were divided into three density fractions by means of heavy liquids. A duplicate portion of one of the coals was divided by sieving into three size fractions. Each fraction was analyzed by oxidation and its percentage composition calculated in terms of fusain, bright coal, and dull coal. Because the weight percent of each fraction was known, a material balance calculation for the whole coal was also made. The resulting reconstituted analysis of the whole coal could be compared to that determined by direct analysis. In addition, specific reaction rate constants were determined for each component and for each whole coal or fraction. Arbitrary reactivity indexes were calculated by dividing by 100 the sum of the products of the percent of each component in the coal and its specific reaction rate constant. The resulting figure was an average reactivity index for each coal or fraction. Weighting the reactivity indexes for each fraction by the percent of the fraction in the coal gave a reactivity index for each whole coal which could be compared to that calculated directly from the whole coal analysis. If oxidation analyses really delineate definite physical entities within the coal, or even definite groups of similar entities, reconstituted analyses calculated from fraction analyses should check closely those made of the whole coal. It probably is true that optical methods identify and describe a greater variety of components than do chemical methods and that variations are wide in the appearance and quantity of those components identified optically. Chemical methods based upon differences in oxidation reaction rates would of necessity be less discriminating, as between similar components, than would optical methods. The procedures followed for oxidizing the samples, analyzing the residues, plotting and calculating the percentage of each component, and calculating its specific reaction rate constant have been fully described.&apos;-&apos; In brief the method originally proposed by Fuchs et al.1 for the determination of fusain consists of the oxidation of small samples of coal in boiling 8N nitric acid in a condenser-fitted flask. After boiling for periods of 1/2 to 4 hr, the unoxidized residue is filtered and washed. The washed residue is treated with normal sodium hydroxide, diluted, and allowed to stand for several hours. The resulting brown liquor is removed, and the filtered residue dried, weighed, ignited, and weighed again. The ash-free residue is expressed as a percent of original dry, ash-free coal. The percent residue is plotted against time, and the extrapolation of this line to zero time gives the percentage of dry ash-free fusain present in the original sample. The shape of the resulting time plots has been explained&apos; by the assumption that they are the result of two different types of reaction, the first part representing a first order reaction with rate a func-

Jan 1, 1956

By T. Cuscino, D. D. Lane, C. Cowherd, T. E. Baxter

Three types of commercially-available dust suppressants, commonly used in the surface mining industry to control fugitive particulate emissions from unpaved roads, were tested in the laboratory for cohesive strength and resistance to reduced effectiveness by large water addi¬tions. Results indicate that each product tested varies in cohesive strength with a range of 34-300 kPa (5-44 psi). Total cohesive strength depends on the aggregate moisture content and the means by which the sample is dried. Results show that laboratory testing can be used as a decision¬making tool concerning the type of dust suppressant for a particular mining operation. Also, the road surface aggre¬gate moisture content u critical to successful dust suppres¬sant performance. Large water additions to the aggregate road surface after initial suppressant application can pro¬duce nondesirable results. A modified wet sieving analysis is presented to test the effect of water addition.

Jan 1, 1984

By Francois E. Heuze

Today, the favored option for disposal of high-level nuclear wastes is their burial in mined caverns. As an alternative, the concept of deep disposal by rock melting (DRM) also has received some attention. DRM entails the injection of waste, in a cavity or borehole, 2 to 3 kilometers down in the earth crust. Granitic rocks are the prime candidate medium. The high thermal loading initially will melt the rock surrounding the waste. Following resolidification, a rock/waste matrix is formed, which should provide isolation for many years. The complex thermal, mechanical, and hydraulic aspects of DRM can be studied best by means of numerical models. The models must accommo¬date the coupling of the physical processes involved, and the temper¬ature dependency of the granite properties, some of which are subject to abrupt discontinuities, during [a]- ß phase transition and melting. This paper outlines a strategy for such complex modeling.

Jan 1, 1982

By P. Barnes

Several interesting and important considerations may be based upon an analysis of the cost of producing Bessemer rails, and the facts thus set forth may be much more clearly emphasized by re ducing each item of cost to its own fractional proportion of the sum total in each branch of the manufacture. The estimate given below is not absolutely complete in minute ness of detail, but it may be fairly taken as a basis for the suggestions to be noted : Perhaps the most striking comments that can be made upon this statement are those arising from a consideration of some of the smaller items, and even the least of these quite loses its insignificance when its proportion of the whole is expressed in actual money, as for the work of a year, or even for a single day. Thus, if the item as be considered, the importance can be clearly

By Irving Cadoff, Kurt Komarek, Edward Miller

Barium can be purified by equilibration with titanium. The melting point of barium was found to be 726.2° i 0.5 °C. The room-temperature lattice parameters of BaTe and Bask are 7.004 * 0.002A and 6.600 * 0.002A. Melting points for BaTe and Base were found to be 1510° * 30°C and 1830° ± 50°C, respectively. HIGH-purity barium and its compounds are difficult to prepare because of the reactivity of barium with the atmosphere and the large heats of formation of the compounds. Purification of barium by vacuum distillation,&apos; and the preparation and properties of barium oxide2 and barium sulfide3 have been reported. However, little has been done on the homologous compounds barium selenide and telluride. PURIFICATION OF BARIUM Distilled barium obtained from King Laboratories was used as the starting material. The analysis supplied with the metal showed the presence of: 0.4 wt pct Sr, 0.001 pct Mg, 0.02 pct F, 0.003 pct Cu, 0.005 pct Na and less than 5 x 10-3 wt pct of any other metallic impurity. Analyses for oxygen and nitrogen were not available. Since there is evidence4 that any barium nitride present in the starting material may decompose on distillation producing nitrogen which can contaminate the distillate, further purification was performed. At elevated temperatures, any nitrogen and oxygen present in barium should be removed by reaction with titanium. Assuming that the solubility of oxygen in liquid barium is negligible near the melting point of barium, any oxygen present will be in the form of BaO. Removal of oxygen from molten barium is expressed by the equation: BaO(S)+ TixOy(S) = Ba(l)+ TixO(y+1)(s) where Ti,Oy and TixO(y+1) are solid solutions of oxygen in titanium. At 1000°C, the change in free energy for this reaction is negative for (y+1)/x +y+1) x (100) 17.5 at. pct O.5 Since reaction with commercially pure titanium (containing 0.07 wt pct oxygen) results in a free energy change for the reaction of -19 kcal per g-atom, slight solubility of oxygen in barium would not hinder the oxygen removal. Since comparable thermodynamic data are not available to permit calculation of the partition of nitrogen between liquid barium and titanium, a similar quantitative relationship cannot be obtained. However, on the basis of work by Kubaschewski and Dench,5 complete removal of nitrogen from liquid barium can be expected. Since the melting point of barium is depressed markedly by small additions of nitrogen,&apos; the change in melting point during reaction of barium with titanium was used to follow the purification reaction. MELTING POINT OF BARIUM A 50-g sample of barium was sealed by arc welding under argon into an all titanium crucible provided with a thermocouple well. The melting point of the sample was determined by thermal analysis, using a Pt/Pt-10 pct Rh thermocouple which was calibrated according to National Bureau of Standards specification6. The crucible was then heated for 48 hr at 950°C in vacuum and the melting point redetermined. This procedure was repeated until three successive thermal analyses agreed within ±0.5oC, the limits of error of the analysis. The melting point increased from an initial value of 720.0°C to a final value of 726.2°C. Analysis on samples quenched from 950°C gave a solubility value of 0.004 wt. pct Ti. Assuming that the titanium-barium phase diagram is similar to those of titanium-magnesium7 and titanium-calcium,8 the solubility of titanium in liquid barium decreases with decreasing temperature. Therefore, the solubility of titanium in liquid barium should be less than 0.004 wt. pctat the melting point (726oC), and the effect of dissolved titanium on the melting point would be negligible. Addition of up to 3 wt pct Sr does not significantly change the melting point of barium,7 so that the effect of the 0.4 wt pct Sr in the starting material will also be negligible. The value of 726.2" ± 0.5C obtained for the melting point of barium can be compared .with a determination carried out by Keller and coworkers in low-carbon steel crucibles,&apos; who obtained a value of 725± 1C, using barium purified by fractional distillation. The higher value obtained in the present investigation is indicative of the effectiveness of titanium in removing traces of nitrogen. PREPARATION OF BaTe AND Base The compounds were prepared by direct reaction

Jan 1, 1961

By J. E. Tobey

UNDER war conditions coal immediately assumes a position of highest importance for coal must carry the basic load for industry. The upward trend in production continued through 1941. Bituminous coal production alone about equaled the total output of bituminous and anthracite in 1940. The figures for 1941 approximated 500,000,000 tons for bituminous, and 54,000,000 tons for anthracite, and production of by-product and beehive coke exceeded that of the previous year. The coal industry, under the National Bituminous Coal Act, is going through a period of readjustment, and is beginning to stabilize itself under the statute. The Federal Mine Inspection Nill became law during the year.

Jan 1, 1942

By Susan B. Leiter

That oxygen in copper has been a source of trouble is well known and that that trouble has been real in the commercial world has been shown by Fuller.&apos; Moore and Beckinsale&apos;s paper2 at the annual meeting of the Institute of Metals in London, 1921, called forth considerable discussion. Prof. T. Turner expressed the opinion that it was not necessary to have cuprous oxide present in sufficiently large quantities to form either globules or seams in order to produce a bad effect if the copper were gassed. This brought up the question of the solubility of oxygen in copper and the authors desired to know whether there were any evidence of such solubility, because their experience was that whenever there was any oxygen in copper it was present in the form of free cuprous oxide, which was practically always in the form of globules. Later Hanson, Marryat, and Ford3 stated that &apos;for all practical purposes cuprous oxide may be regarded as insoluble in copper. However, they found particles of the eutectic to coalesce to form much larger particles. They suggested that cuprous oxide was actually slightly soluble in copper, for it was difficult otherwise to understand the mechanism by which such coalescence could take place. W. E. Ruder, in discussing that paper, said that his experiments had led him to conclude that a slight solubility must exist to allow for the ready coalescence of oxide particles, but conductivity tests convinced him that that solubility was very small. Nevertheless, there appeared to be a state of admixture of oxide with copper that closely resembled a colloidal mixture which at first was mistaken for a true solution and which usually existed at the grain boundaries. The purpose of this paper is to give the results of some investigations, begun in September, 1921, which would seem to show that although cuprous oxide may be only slightly soluble: (1) this solubility is sufficient

Jan 1, 1926

By J. E. Stukel, J. Cocubinsky

A CONSIDERABLE amount of information is available on the equilibrium distribution of manganese between slag and metal under oxidizing conditions. These data have increased our knowledge of the manganese reactions in the open hearth, ladle, and ingot mold. In contrast, there is a paucity of data on the slag-metal distribution of manganese under reducing conditions. The purpose of the present investigation was to study the equilibrium distribution of manganese between blast-furnace type slags and iron saturated with carbon. Experimental Method Furnace: The induction furnace used for the experiments is shown in Fig. 1. A 1 in. pipe, attached to the transite cover, was fitted with a window through which the charge could be observed. Material could be introduced into the furnace through a tee and plug without removing the cover. A graph-it cylinder (3 in. ID and 10&apos;/2 in. long), centered within the induction coil, was used as a heating element. During a test, a zircon plug kept the top of the furnace from becoming too hot from heat radiation. At the bottom, a graphite block on the vertical center line of the furnace and extending 1 1/2 in. into the coil, was used as a support for the graphite crucibles containing the melt. The graphite crucibles, machined from regular carbon electrode stock, had a 2% in. OD with 3/16 in. walls and were 5% in. long. The fumes present in the furnace during the early part of a run made optical readings uncertain. A noble metal thermocouple was, therefore, adopted to measure the temperatures. The arrangement used, shown in Fig. 1, allowed the silmanite protection tube to be replaced with a minimum effort. The thermocouple was calibrated against a standard Pt-Pt-Rh thermocouple in a fused quartz protection tube. The latter was inserted in the molten iron by removing the glass window on the cover. The lower couple was found to be very sensitive to temperature changes. To insure accurate temperature readings, the graphite crucibles were made to fit tightly against the silmanite protection tube. Further, to avoid contamination of the thermocouple by carbon, the silmanite tube was changed and the calibration procedure was repeated at frequent intervals. By using this temperature measuring technique, the furnace was easily held within *1O°C of the desired temperature. Because of the small free space in the furnace, no attempt was made to control the atmosphere. It

Jan 1, 1955

By E. L. Swarts

In the course of a program on high-temperature processing and electrowinning of uranium at the Knolls Atomic Power Laboratory,&apos;&apos; it became necessary to give attention to the interaction of molten uranium with graphite. Although it is known3 that a protective interface layer may form, details of this reaction have not been reported. Unfortunately it was impossible to complete the planned experimental program. However, the general problem is considered of sufficient interest to warrant reporting those preliminary results actually obtained. EXPERIMENTAL PROCEDURE Interface carbide layers were formed by melting samples of cleaned uranium metal in small closed graphite crucibles. Equilibrations were conducted in vacuo or in an atmosphere of dry helium at temperatures ranging from 1150" to 1400°C and for periods of from 24 to 240 hr.

Jan 1, 1960

[ ] S. H. Ash (Mining Industry Continues with Lower Fatal-Injury Rates, P. 257) was born in Roslyn, Wash. and attended Lehigh University and University of Washington. He received a B.S. and E.M. degree in mining engineering. Mr. Ash was supervising engineer in charge of work of Safety Div., Bureau of Mines, eastern Pennsylvania and the states of N. Y., Del., N. J. and the New England states. He was appointed chief engineer of Metal and Nonmetal Mining Section of the Mineral Production Security Div., Bureau of Mines, July 1942. At present he is chief engineer, Safety Branch, U. S. Bureau of Mines. Besides holding membership in AIME, he is a member of National Honorary Engineering Society, Society of American Military Engineers, Tau Beta Pi and many other societies.

Jan 1, 1952

The Duluth Engineers&apos; Club was formally organized on the evening of Aug. 5, 1918, at a meeting .attended by over l00 members of the several engineering professions. W. G. Swart, a member of our Institute, was elected the first President of the Club. At the organization meeting, an opportunity was given, to Alfred D. Flinn, Secretary of the United Engineering Society, to outline the assistance that is being rendered to the Federal Government in the present contingency by members of the engineering profession. Membership in the Duluth Club is to be open to mining engineers on the iron ranges as well as to the residents of the city of Duluth.

Jan 10, 1918

GERARD B. ROSENBLATT,* Salt Lake City, Utah (written discussion?). -Mr. Eschholz attacks this problem from what appears to me to be the proper angle. He does not limit his viewpoint to the attainment of ideal results under conditions approximating laboratory practice, but rather discusses actual commercial conditions that must be maintained in large-scale operations, where continuity of service without expert attendance is one of the prime considerations. I am of the opinion that Mr. Eschholz has not given sufficient consideration to the commercial possibilities of what he describes as System B, the use of low-tension a.-c. industrial or lighting circuits for supplying power to Cottrell treaters through the medium of a step-up transformer and a synchronously driven rectifier, without the use of motor-generators. It is true that, to date, few installations on a large scale have used this system, but I believe that when the conditions of power supply are suitable, and when proper precautions are taken, this system can be used successfully and to advantage. where at present it is considered necessary to use motor-generator sets. In the average commercial Cottrell installation of any size, the motor-generator set is used for two purposes: (1) To isolate the industrial supply circuit from the Cottrell circuit. (2) To. afford, an easily operated and smooth system of control for the Cottrell treater voltage With proper engineering, both of these objects can be accomplished without the use of motor-generator sets.

Jan 10, 1918

By L. H. Robinson

Triaxial compression tests on Indiana limestone indicate that chemical additives in the pore fluids can increase or decrease the strength in plastic failure but not in brittle failure. Tests using a series of the sodium salts of dicarboxylic acids show that odd-number carbon-atom chains decrease the yield strength as much as 3.0 x 10 3 psi, and even-number carbon-atom chains increase the yield strength as much as 9.0 x 102 psi. ,The most effective chemical (sodium citrate) decreased the yield strength of Indiana limestone from 16.0 x 103 to 12.0 x 103 psi. The chemical additives investigated have no influence on microbit drilling rate when drilling with zero differential pressure. However, when drilling at a 2.0 x 103-psi pressure differeniial and using an odd-number carbon chain compound as the circulating fluid, the roller bit drilling rates were slower than with water whereas the drag bit drilling rates were faster. One even-number carbon chain compound added to the circulating fluid produces the opposite effect: the roller bit drilling rate is slightly faster than with water and the drag bit slower than with water. INTRODUCTION A Russian book by Rehbinderl published in 1944 generated much interest in the possibility of aiding and accelerating the destruction of solids by the action of a liquid in which the solids are deformed. This book describes a process in which microcracks are generated during elastic deformation. To describe this process, the rock is divided into three zones: (1) the zone in which the destruction takes place, (2) the predestruc-tion zone (an affected area immediately below the destroyed zone) and (3) the undisturbed specimen. Consider a load applied normally to a surface of an infinite slab of rock. Immediately below the point of application of the load, the rock is destroyed by compression or shear forces. Below this area of destruction, because of a great number of discontinuities ranging from defects to weak points in crystals of discontinuities in crystal latices, very small cracks are created in or between the crystals (often referred to as microcracks). Upon removing the load, the broken rock in the destroyed zone could be removed. In the lower predestruction zone, however, the microcracks in and between the crystals could disappear by the process of rehealing, i.e., the molecular attraction from one side of the crack to the other side being sufficient to completely eliminate the crack. Thus, a large number of these microcracks possibly exist only for a relatively short period of time. The concept of small cracks being generated within the crystals of a rock is not unreasonable. If the rock matrix is deformed below the yield point, some of the defects present within the crystalline structure could start small cracks through the interior of the grains. Upon removal of the load, these microcracks reheal (or the newly generated surfaces come back together) so that all evidence of cracks completely disappears. Under various types of loading, and in various types of fluids, the rehealing of these cracks would be time dependent. If a liquid adhered to the surface of a rock, it could penetrate into the microcracks and thus delay or prevent the rehealing process. This suggests that the prevention of healing of the microcracks may be dependent upon the wetting characteristics of the solid. Thus, rocks which are water-wet should be more easily destroyed in water than in nonpolar hydrocarbon liquid. Adsorption of a liquid could also reduce the free surface energy which could explain the decrease in strengths of materials under nonrepetitive-type loading. Rehbinder&apos;s work prompted Boozer, Hiller and Serdengecti 2 to examine the effects of pore fluids on the deformation of rocks subjected to triaxial compression over a range of confining pressures, temperatures and strain rates. Fluids which strongly adsorbed on the rock grain surfaces decreased the strength of sandstone and limestone, which deformed plastically. For certain strain

By J. L. Gillson

THE big mass of anorthosite in the Lake Sanford district and the bodies of titaniferous magnetite that occur in a small area near the south margin of the mass have been described repeatedly, and the puzzling problems of the genesis of the rocks and ores have stimulated the deductive reasoning of geologists for a hundred years. Some of these men have taken a leading part1-15 in describing the anorthosite rock and forming hypotheses concerning its origin; some have contributed most to the study of the ore deposits;&apos;"= and some have made classical Studies3,4,21-27 introducing a basic approach to the problems of the anorthosite rock and genesis of the titaniferous magnetites. Much of the writing on the problems of rock and ore genesis has been based on physical-chemical reasoning rather than on field and microscope observations of the rocks and ores. Most of these geologists conclude that the anorthosite was formed by true magmatic crystallization, involving previous settling or squeezing out of ferromagnesian minerals from the parent magma. The associated gabbro is a separate segregation or later intrusion, and the lighter colored and finer grained facies of the anorthosite is either a chilled border zone of the anorthosite or the result of granulation by crushing of the coarse, dark blue rock of the main mass. This blue rock, called the Marcy type, is named after the higest peak in the range. The finer grained and lighter colored rock is called the White-face, after another mountain appropriately named for a cliff colored by this facies of the anorthosite. In explaining the genesis of the ores the authors have reached no general agreement, but all consider them to be dominantly the result of magmatic processes rather than the result of replacement by pneu-matolytic or hydrothermal processes. However, in the conclusions of two authors, Osborne27 and Ste-phenson," the reader is told positively that the ore minerals were introduced after the wall rock was solid and also that the oxides are later than the silicates. This seems to mean that the ore came in as a later intrusion, like a dike, since Osborne speaks of filter pressing and later injection of a residual magma. Stephenson agrees in general with Osborne but disagrees with his conclusion that ore does not grade into country rock. Singewald22 calls in "mineralizers" to participate in magmatic deposition. Stephenson ends his paper with a statement that replacement was the dominant process for the introduction of ore with anorthosite. Hence both Singewald and Stephenson call on pneumato-lytic or hydrothermal processes to supplement magmatic crystallization from a silicate melt, but they cannot quite bring themselves to state that the orebodies formed in that way. In their conclusions the ores are still magmatic segregations and magmatic injections and—almost as an afterthought— "replacements." According to Bateman18 there was a gravitational accumulation process of the iron silicates and oxides, which were injected later. Rambere explains the ores entirely on physical-chemical theory, as does Evrard.17 Buddington and associates,10 in a paper presented to the Geological Society of America in 1953, believe the facts observed prove that the magnetite-ilmenite formed at magmatic temperatures. The present writer&apos;s conclusions, given here, were first presented in 1947 in Industrial Minerals and Rocks.= Since the papers of Ramberg, Bateman, and Buddington, published after 1947, gave no recognition to those conclusions that differ from their own, the writer has taken an opportunity to restudy the area in the field, and to examine a number of microscopic sections, and now presents the evidence more thoroughly than he had an opportunity to do in the

Jan 1, 1957

By C. G. Goetzel

Until recently porous bronzes have found many applications for self-lubricating bearings in the automotive, electrical, household appliance and general machine industries. The bulk of an annual production of several million pounds of copper powder had gone into the manufacture of these articles, of which by now more than a billion are in service. However, the war has brought severe curtailment of these bearings because of the scarcity of the two main constituents, copper and tin. The development of substitute materials of equal or superior properties has led to a large-scale replacement by products made from iron powder. In spite of the diminished interest in powdered copper-tin alloys caused by this trend, it was believed worth while to investigate some mechanical properties of these materials as a reference base for substitutes. In addition, experiments using the hot-press method were incorporated to investigate possibilities of saving vital equipment or opening new fields of applications. It must be assumed that by this time the powder metallurgy process of making porous bronzes, a development that found its first industrial applications more than 10 years ago, is well known in engineering. The patent literature and bibliography is volu- minous, most publications referring to porous, self-lubricating bronzes, containing about 10 per cent tin and I to 5 per cent graphite, with porosities in the range of 25 to 35 per cent.l-7 The excellent antifriction properties of these bearings, caused by the uniform impregnation with oil, are dependent on the interconnection of the pores and the uniform distribution of the graphite inclusions. The sintering mechanism of porous bronze, with its structural changes during the transformation of the metal powder into the sintered bearing has been shown in colored photomicrographs by Hall.* Diffusion between copper and tin was found to begin within one minute, when tin-rich transitory phases were formed. After 25 min. a homogeneous matrix of alpha was reached for an alloy containing 9.5 per cent tin and 6 per cent graphite. Price, Williams and Garrand,9 studying certain metal powder combinations in which sintering is accompanied by the cementing action of a liquid phase, including a 90-10 bronze sintered at 925°C., have found that if the treatment is carried out within the liquidus and solidus temperature range of the system, a peculiar process of alternate solution and precipitation occurs. The particles of the major solid constituent are dissolved in the minor liquid phase, but thereafter are reprecipi-tated on certain nuclei, which develop into large grains, usually rounded.

Jan 1, 1945

By Sylvan Z. Beer

Aluminum phosphide was synthesized and grown in solution of excess aluminum using a modified two-temperature technique. An inversion in the density difference between ALP and molten aluminum takes place at about 1100°. Dispersed nuclei can act as sources for further crystal growth in a manner resembling ripening. Advantage was taken of this phenomenon by introducing a stirring motion into the molten liquid. This was done with a split-phase 10-kH2 rotating magnetic field produced by four horizontal coils placed symmetrically about the furnace at the level of the molten metal. The method also prevents the formation of a surface film which would impede the reaction. By this technique vastly improved yields were obtained and flat crystals 5 by 5 by 0.5 mm were grown at lower temperatures and at greater rates than heretofore. THE family of III-V intermetallic compounds has received much attention since the prediction of their semiconducting properties in the early 1950s. Of the family, A1P has perhaps the highest band gap of those compounds normally possessing the zinc-blende structure. But it has been least studied because it is difficult to handle and grow. The handling difficulties have been dealt with elsewhere and it is sufficient to say here that, by various techniques, many of the difficulties can be overcome.&apos; The difficulties encountered in crystal growth can be related to the refractory nature of A1P and in turn to its high band gap. Because of the anticipated high melting point of the material and the accompanying high phosphorus vapor pressure, the reported work on synthesis and growth was done by epitaxial synthesis-growth via chlorine2 and iodine3 transport and from solution of excess aluminum by the two-temperature technique.4&apos;5 The transport-grown crystals take on the dimensions of the substrate but do not grow easily in thickness. In the usual two-temperature technique as applied on the synthesis of Alp, the temperature of the molten aluminum is kept at 1000° to 1250°C while the phosphorus is maintained at 1 to 20 atm. A thin film of aluminum phosphide and oxide form immediately, impeding the reaction and affecting the yield. Attempts to grow the Alp from such solutions by the methods used to grow Gap and InP from excess gallium and indium have not been successful. As discussed in the preceding paper,5 the yield can be greatly increased

Jan 1, 1969

AUGUST began with a reminder that warfare was still in progress in the world, in that the Greeks, still at war with Turkey, threatened Constantinople in spite of the small British and French forces of occupation and opened a vista of international dangers. There was in this, moreover, a recollection that religious questions in India had prevented the British from permitting a real settlement of the Turkish question, wherein the absence of Russia as a great power is missed. Civil warfare also continued in Ireland and China. Even in the military way the world is far from being at peace. Bloody fighting between the Fascisti (anti-communists) and the com-munists in Italy led to several provinces being put under martial law, but after a while these disturbances were quelled. In the latter part of the month the assassination of Michael Collins in Ireland produced a great shock. From China, however, there came rather favorable news, indicating the early reintegration of that country, which sooner or later ought to play an important part in world affairs. Economically, instead of there being any improve-ment, there grew a clearer perception of how bad things really are. Italian politics were in chaos through inability to find anyone to accept the premiership and assume the all but hopeless task of averting national bankruptcy. The French, too, began to see their own position in true colors, and especially to see how in reconstruction they had incurred debts on the strength of what they hoped to collect from Germany, with at last the understanding that the Germans could not pay and that France herself was thereby put in a desper-ate economic position. As for the Germans, them-selves their Reichsbank defaulted on ordinary bills early in August. As the month wore on the value of marks fell more and more and at the end it appeared that Germany was on the verge of economic collapse. On Aug. 7, another international conference (with America again absent) was assembled in London, this being the thirteenth since the war, and there was a general feeling that it would be the last. The prime question was what is to be done about the German reparations, but underlying was the whole subject of the entente. The conference opened like a meeting of importunate creditors, doubtful whether the debtor had any tangible assets. On Aug. 14 this conference broke up without coming to any useful conclusion. Indeed, the acrimony among the premiers was so sharp that even the entente between Great Britain and France was endangered. The international situation was saved only by the Reparations Commission excusing the Germans from the payment of 50,000,000 gold marks that come due on Aug. 15 But although the entente was nominally preserved there is no longer any illusion about the interests of Great Britain and France being different and that henceforth they will play their own hands. The London conference was really an effort to maintain the partnership, and it failed.

Jan 9, 1922