Search Documents

By Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as sand-cast and as heat-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brinell and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. THE demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.1 Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergranular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about-950° F., quenching in oil or in cold or boiling water, and artificially aging

Jan 7, 1925

By D. M. Warner, Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as 8and-cast and as heal-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brine11 and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. The demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.' Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergran-ular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about 950" F., quenching in oil or in cold or boiling water, and artificially aging

Jan 1, 1926

THERE have always been in this world men of such keen intelligence that with their discourse they have been capable of infinite and various inventions that are as beneficial as they are simultaneously harmful to the human body. Wherefore, from day to day, we see unfolded before our eyes some of these that greatly astound our minds, and we remain so stupefied that when-we think of them we are not able to control our faculties for some time, both from considering by what necessity or purpose these men were goaded, as well as from contemplating the profound subtlety of their discoveries, which, in truth, are such that they are awarded the greatest commendation by noble minds. By following their counsels and with their aid, there have been* some astute and lever captains who have had certain pots or balls of earthenware carried by their infantry, expressly filled with compositions of powder or other unctuous liquors disposed to ignite easily. When they meet the enemy in battle and come up close to them, they try to strike vigorously with these in the first assault in an effort to throw them into disorder and to make them give way by breaking them up and drawing them out of formation. The smoke is harmful, but the fire very much more so. These are made in this way. Take the number of vessels that you have to make-it does not matter whether they are raw or baked as long as they are well freed from the moisture of the clay-and fill them a little more than half full with coarse gunpowder which has mixed in it pounded Grecian pitch and at least a third of crushed sulphur. Then pour in a covering a dito thick of strained pig fat mixed with powder. This keeps it from falling out when it is thrown and keeps the fire slower until it reaches the enemy. When this has been made, open up the pig fat a little at one side when you wish to throw it and put in a little fuse or a little good powder and apply fire, holding it in your hand until you see that the fire has taken hold well. Then throw it, choosing your time. A liquid composition is also made in a kettle in which are put pork fat, petroleum oil, oil of sulphur, live sulphur, [163] doubly refined saltpeter,

Jan 1, 1942

By K.D. White, Chester W. Washburne

Colombia has an almost ideal situation with lespect to the world's markets, being only a short distance from the Panama Canal and the West Indies. The sailing distance from its Caribbean ports to New York is less than that from Tampico. Geographically, Colombia consists of three systems of broad mountain ranges separated by two long narrow valleys. The Cauca River valley separates the Western or Coastal range from the Central range. On the west side of the Coastal range are the Atrato and San Juan Rivers. The Central and Eastern ranges are separated by the Magdalena River valley. In the department of Santander the Eastern range divides, one branch continuing northward as the Cordillera of Perija, the other turning eastward across Venezuela as the Cordillera of Merida. Between these ranges is the great basin occupied by Lake Maracaibo. These valleys consist mainly of long narrow reentrants or tongues of Tertiary sediments between the older rocks of the mountain ranges. The late Miocene and younger sediments seem to have been deposited in separated basins, but the Cretaceous and possibly some earlier Tertiary strata were laid down more or less continuously over a great part of Colombia and Venezuela. These strata were subsequently folded into the present ranges. The deposition of the Cretaceous and of some of the Tertiary was in a great sea, the main land mass being in Brazil, with land probably along some of the cores of the present mountain systems. The sediments, except the Lower Cretaceous, vary markedly in character and thickness. An illustration is seen in the massive series of non-marine conglomerates and sandstones of the upper Magdalena River valley, near Honda, which are almost wholly wanting in the coastal sections where marine sediments prevail. The oldest rocks bearing on the search for oil are the black carbonaceous and bituminous shales, limestones, and cherts of the upper part of the Lower Cretaceous. These probably are the main source of oil in both Colombia and Venezuela. They include thick bodies of true "oil shale." Above the carbonaceous and bituminous beds, lies a series of many thousand feet of clastic sediments. The most noticeable and easily recognizable formation among these clastic sediments is the "coal-bearing series," which may be either upper Cretaceous or Eocene. The

Jan 1, 1923

By Chester Washburne

COLOMBIA has an almost ideal situation with respect to the world's markets, being only a short distance from the Panama canal and the West Indies. The sailing distance from its Caribbean ports to New York is less than that from Tampico. Geographically, Colombia consists of three systems of broad mountain ranges separated by two long narrow valleys. The Cauca River valley separates the Western or Coastal range from the Central range. On the west side of the Coastal range are the Atrato and San Juan Rivers. The Central and Eastern ranges are separated by the Magdalena River valley. In the department of Santander the Eastern range divides, one branch continuing northward as the Cordillera of Perija, the other turning eastward across Venezuela as the Cordillera of Merida. Between these ranges is the great basin occupied by Lake Maracaibo. These valleys consist mainly of long narrow reëntrants or tongues of Tertiary sediments between the older rocks of the mountain ranges. The late Miocene and younger sediments seem to have been deposited in separated basins, but the Cretaceous and possibly some earlier Tertiary strata were laid down more or less continuously over a great part of .Colombia and Venezuela. These strata were subsequently folded into the present ranges. The deposition of the Cretaceous and of some of the Tertiary was in a great sea, the main land mass being in Brazil, with land probably along some of the cores of the present mountain systems. The sediments, except the Lower Cretaceous, vary markedly in character and thickness. An illustration is seen in the massive series of non-marine conglomerates and sandstones of the upper Magdalena River valley, near Honda, which are almost wholly wanting in the coastal sections where marine sediments prevail. The oldest rocks bearing on the search for oil are the black carbonaceous and bituminous shales, limestones, and cherts of the upper part of the Lower Cretaceous. These probably are the main source of oil in both Colombia and Venezuela. They include thick bodies of true "oil shale. Above the carbonaceous and bituminous beds, lies a series of many thousand feet of clastic sediments. The most noticeable and easily recognizable formation among these clastic sediments is the "coal-bearing series," which may be either upper Cretaceous or Eocene. The

Jan 6, 1922

By K. D. White, Chester W. Washburne

Colombia has an almost ideal situation with lespect to the world's markets, being only a short distance from the Panama Canal and the West Indies. The sailing distance from its Caribbean ports to New York is less than that from Tampico. Geographically, Colombia consists of three systems of broad mountain ranges separated by two long narrow valleys. The Cauca River valley separates the Western or Coastal range from the Central range. On the west side of the Coastal range are the Atrato and San Juan Rivers. The Central and Eastern ranges are separated by the Magdalena River valley. In the department of Santander the Eastern range divides, one branch continuing northward as the Cordillera of Perija, the other turning eastward across Venezuela as the Cordillera of Merida. Between these ranges is the great basin occupied by Lake Maracaibo. These valleys consist mainly of long narrow reentrants or tongues of Tertiary sediments between the older rocks of the mountain ranges. The late Miocene and younger sediments seem to have been deposited in separated basins, but the Cretaceous and possibly some earlier Tertiary strata were laid down more or less continuously over a great part of Colombia and Venezuela. These strata were subsequently folded into the present ranges. The deposition of the Cretaceous and of some of the Tertiary was in a great sea, the main land mass being in Brazil, with land probably along some of the cores of the present mountain systems. The sediments, except the Lower Cretaceous, vary markedly in character and thickness. An illustration is seen in the massive series of non-marine conglomerates and sandstones of the upper Magdalena River valley, near Honda, which are almost wholly wanting in the coastal sections where marine sediments prevail. The oldest rocks bearing on the search for oil are the black carbonaceous and bituminous shales, limestones, and cherts of the upper part of the Lower Cretaceous. These probably are the main source of oil in both Colombia and Venezuela. They include thick bodies of true "oil shale." Above the carbonaceous and bituminous beds, lies a series of many thousand feet of clastic sediments. The most noticeable and easily recognizable formation among these clastic sediments is the "coal-bearing series," which may be either upper Cretaceous or Eocene. The

Jan 1, 1923

By Leonard Waldo

The recent and rapid development of the physics of engineering materials at temperatures as low as that of liquid air and as high as that of the electric are, has drawn renewed attention to the absence of tables, properly printed and spaced, for the convenient and accurate translation of temperature from centigrade to Fahrenheit scales and vice versa. It is to be noted that the Fahrenheit scale is the almost universal usage in foundries and shops in the United States, though the laboratories of the same works employ the centigrade notation. The growing use of the electric furnace in Germany and France calls for much American citation all in centigrade high temperatures, and while the arithmetical calculation is simple, it becomes burdensome when often repeated. I have been surprised at the numerous reprints of Table I. from centigrade to Fahrenheit degrees, first privately printed for personal use, which have been made by works, blue-prints, text-books, and technical journals, and I hope that Table II., from Fahrenheit to centigrade degrees, will be equally useful. For mental calculation the easiest rule to convert centigrade into Fahrenheit is to add 32° to twice the centigrade reading less one-tenth of this product: Thus 1000' C. = 2000" — 200" + 32" = 1832" F., and to convert Fahrenheit to centigrade, subtract 32" from the Fahrenheit reading, multiply by 10 and divide by 2 and 9 successively : Thus 1000° F. = 1000° — 32° = 968° X 10 = 9680° - 2 = 4840° - 9 = 537.77° C. Another and often very convenient method is by 'use of a graphic construction as follows :

Jan 1, 1913

By J. W. Evans

ONE possible method for the separation of hafnium from zirconium is by the vapor phase oxidation of the purified mixed chlorides. An important factor for success depends on the difference in free energies of the following reactions: ZrCl(g) + O2 = ZrO2(s) + 2C12 [1] HfCl4(g) + O2 = HfO2(s) + 2C12. [2] Prakash and Sundaram1 have calculated these values from certain data and carried out experimental work with partial success. However, their free energy values for reaction 2 diverge rather widely from other data which are presented here. The possibility of successful separation is briefly considered in the light of these alternative values. Table I shows the free energy values (?F°) for reactions 1 and 2 derived from the recent compilation of data on oxides and chlorides by Glassner.2 The corresponding values of Prakash and Sundaram for the same temperatures are also shown. The alternative values to those of Prakash and Sundaram for reaction 2 are substantially confirmed by the data of Kubaschewski and Evans" and Cough-lin' on heats of formation, entropies, and heats of vaporization. In spite of the considerable uncertainty in the hafnium data it is reasonable to suppose that the oxide-chloride free energy difference for two such chemically similar elements would not be very far apart. These figures indicate clearly that the oxidation of hafnium chloride is appreciable at all temperatures. Nevertheless, there is a significant difference between the values for reactions 1 and 2

Jan 1, 1959

By T. R. Braithwaite

The brief comments made in this chapter deal mainly with shaft sinking, but don't assume that freezing techniques apply only to shaft sinking. They can be used on tunnel work, on such things as liquid gas storage in sediment, and I think you will probably see other applications for it as we go along. The method was first developed in 1883 and was used to sink shallow shafts through water-bearing overburden in Germany and in England. One of the early shafts was in Germany and was sunk by freezing to 310-ft depth. The project required 17 months for drilling, roughly 5 1/2 months for freezing, and another 7 months for sinking, giving an average progress of 10 ½ fpm. Fortunately there have been numerous improvements and new developments in this technique through the years. With equipment and techniques available today, we can take a 20-ft-diam shaft down through 2000 ft of water-saturated overburden and the time schedule runs roughly 4 months for site preparation, freeze-hole drilling, installing the casings, and setting up the plant; 4 ½ months for freezing; and 6 months for excavating and installing permanent linings. This gives a progress rate of about 140 fpm, on average. I might qualify that a little in that the special linings that are required for some formations can affect the time. If it's straightforward sinking where one can use a heavy concrete lining, up to 630-640 fpm may be achieved in a shaft; but with special cast-iron tubbing or types like that, 5 fpd is pretty good progress, so the lining does affect the time. The freezing method is used mainly for sinking shafts through unstable water-bearing formations which cannot be grouted either effectively or economically and which are too deep to enclose in pile casing. Even with overburden, grouting methods available today can handle roughly 100 lb water pressure; in the range of, say, 100 to 150 ft from the surface, it's very often best to grout 40 or 50 ft. You normally drive a pile casing and go through it. Below that range, freezing is very often the economical

Jan 1, 1970

By W. E. Dunn

CHLORINATION of titanium ores and slags is the source of TiCl,4 intermediate between ore and metal. A number of chlorinators are operating in the United States using a wide diversity of ores. These chlorinators vary in design to accommodate the ore source, but all use chlorine and carbon.

Jan 1, 1961

By Charles R. Simcoe

It was pointed out in a recent paper'g that the initial flow stress of as-quenched martensite is very low even in an alloy steel with an M, well above room temperature. It was also shown that the high ultimate tensile strength resulted from a very high rate of work

Jan 1, 1967

By Joseph N. Morrison

A comprehensive solution is offered to the problem of dust emissions at belt conveyor transfer points. Details of enclosure design are discussed and a straightforward procedure for calculating required dust control exhaust volume is presented. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds. enclosure openings, material flow rate, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these questions are handled by means of a "fill-in-the-blanks" type of calculation form, permitting quick, reliable solutions by relative "non-experts."

Jan 1, 1972

By T. D. Yensen

IF the question should be asked at this time: "Does pure iron have allotropic transformations?" the reply would necessarily be, "We do not know." And it is doubtful whether anybody, anywhere, is in a FIG. 1.-EFFECT OF CARBON ON HYSTERESIS LOSS OF IRON-SILICON ALLOYS. (ALL OTHER IMPURITIES AND EFFECT. OF GRAIN SIZE ELIMINATED.) position to make any other reply at this time, for the simple reason that pure iron has not yet been made and tested. The nearest approach to it contains either an appreciable amount of carbon or else an appreciable amount of oxygen (a few hundredths of a per cent.). But why be con-

Jan 1, 1929

By Nick Warren

The problem considered is that of predicting rock physical properties from observations of the structure of the rock. The approach here departs from previous studies in that both the physical properties and structural features are taken as statistical data and the relations between them are cast as statistical functions. This approach I have termed a "quantitative petrostructure analysis". This Paper deals with two aspects of making such a study; parameterizing patterns of topographic features of rock, and characterizing variables to allow correlation studies to be carried out. The principle of a quantitative petrostructure analysis is outlined and illustrated using maps from two samples of Conway granite.

Jan 1, 1982

By Ralph Sherman

THE remarkable increase in the distribution of the small underfeed stoker for use in furnaces and boilers in small industrial plants, apartment houses and homes has brought producers and distributors of bituminous coal to consider the problem of which coals and which sizes are best suited to this market. Many papers have also appeared, mostly in the trade journals, discussing the problem of the combustion of various coals and various sizes of coal in small stokers. Much difference of opinion has been apparent in these articles; due often, it would appear, to a mis-understanding of the fundamentals of the process of combustion in the stoker fuel bed. During the past year and a half, a program of research has been conducted at Battelle Memorial Institute: (1) On the process of combus-tion in the fuel bed of the small stoker, sponsored by Battelle Memorial Institute, and (2) on the relation of the characteristics of bituminous coals to their performance on small underfeed stokers, sponsored by Bituminous Coal Research, Inc. As a result of this program of research, two publica-tions have been made, one1 dealing with the problem of clinker formation, and the other2 with the relation of the size of the coal fed to the stoker hopper to that of the coal that reaches the retort to be burned. The experimental research on the relation of size to the performance of the coal is being actively continued. A publication of Bituminous Coal Research, Inc. presenting the data obtained on the performance of several sizes of four typical bituminous coals will appear shortly. Because of the early appearance of that publication, the present paper includes few numerical data. The purpose of this paper is to follow the coal from the hopper through the furnace with a discussion of the various actions that occur, in the hope that it will lead to a clearer understanding of the relation of the type of coal, the size of coal, and other characteristics, to the performance. The authors do not pretend to have obtained the answers to all the complex questions involved; many unanswered questions will be proposed on which future research work is planned.

Jan 1, 1936

By Wm. Hamilton Merritt

IN this paper, which I have the honor to submit to the Institute, it is my intention to treat especially of that part of the North Staffordshire field which converges to a long tongue in the neighborhood of Congleton, and which includes the villages of New Chapel, Ford Green, Norton, Biddulph, Bradley Green, Gillow Heath, and the immediate vicinity. My object is not so much to give a minute description of the geology or systems of mining and smelting, as by a general review, some idea of the extraordinary facilities for the production of excellent iron, which have enabled this district to maintain its position more successfully than any of its rivals against the late depression in trade. The North Staffordshire coal field has the Cheshire and Lancashire fields some thirty-five miles to the north, those of Derbyshire and Nottinghamshire forty miles to the east, those of South Staffordshire and Shropshire, about thirty miles to the south, and the Denbighshire and Flintshire fields some forty miles to the west. It is highly probable that the coal continues under the new red sandstone to the Western and Southern fields as the dips on both sides, and absence of large faults, make it impossible to come to any other conclusion. In a section of this coal field, from Chatterly to Whitfield, thirty-two workable seams of coal are shown, of an aggregate thickness of 130 feet, varying from 2 feet 6 inches to 7 feet, and thirteen seams of ironstone, 24 feet, averaging from 2 to 4 feet. All of these seams have been minutely described in a paper by Mr. Charles J. Homer, read in 1875 before the British Iron and Steel Institute. In the northern part, to which I especially wish to direct your attention, the beds lie in a V-shaped basin, the underlying millstone grit and Yoredale rocks rising and forming escarpments on either side of the valley containing the coal. Throughout this district, at the outcrop of the coal, there are indications of old workings. A shaft 4 to 5 feet in diameter reaches the coal at about 14 yards from the surface, and from it the coal has

Jan 1, 1880

By William Hamilton Merritt

In this paper, which I have the honor to submit to the Institute, it is my intention to treat especially of that part of the North Staffordshire field which converges to a long tongue in the neighborhood of Congleton, and which includes the villages of New Chapel, Ford Green, Norton, Biddulph, Bradley Green, Gillow Heath, and the immediate vicinity. My object-is not so much to give a minute description of the geology or systems of mining and smelting, as by a general review, some idea of the extraordinary facilities for the production of excellent iron, which have enabled this district to maintain its position more successfully than any of its rivals against the late depression in trade. The North Staffordshire coal field has the Cheshire and Laucashire fields some thirty-five miles to the north, those of Derbyshire and Nottinghamshire forty miles to the east, those of South Staffordshire and Shropshire, about thirty miles to the south, and the Denbighshire and Flintshire fields some forty miles to the west. It is highly probable that the coal continues under the new red sandstone to the Western and Southern fields as the dips on both sides, and absence of large faults, make it impossible to come to any other conclusion. In a section of this coal field, from Chatterly to Whitfield, thirtytwo workable seams of coal are shown, of an aggregate thickness of 130 feet, varying from 2 feet 6 inches to 7 feet, and thirteen seams of ironstone, 24 feet, averaging from 2 to 4 feet. All of these seams have been minutely described in a paper by Mr. Charles J. Homer, read in 1875 before the British Iron and Steel Institute. In the northern part, to which I especially wish to direct your attention, the beds lie in a V-shaped basin, the underlying millstone grit and Yoredale rocks rising and forming escarpments on either side of the valley containing the coal. Throughout this district, at the outcrop of the coal, there are indications of old workings. A shaft 4 to 5 feet in diameter reaches the coal at about 14 yards from the surface, and from it the coal has

Jan 1, 1880

By R. H. B. Jones

THIS paper reviews pertinent geology of the Biwabik iron formation, Mesabi Range, Minnesota. This iron formation is divisible into four members. Each member is distinctive and contains marker horizons, which are recognizable throughout all phases of alteration from lean, fresh rock to high-grade iron ore. Some beds have a larger magnetite content than others. During the process of ore genesis, which is essentially an oxidation process, the magnetite content is lowered. Alteration from iron formation to ore includes both oxidation of iron minerals and silica removal by leaching and these distinct processes progress at variable rates for different locations and structures. Magnetic intensities, of each horizon of the iron formation are dependent chiefly upon its preoxidation magnetite content, upon the subsequent degree of oxidation, upon the character of the enclosing rocks, and on the extent of fracturing, folding, or faulting. The results of a number of magnetic surveys are described and are correlated with results of drill-hole and mine exploration and development. The magnetic anomalies obtained are discussed in relation to phases of formation of ore within the iron formation.

Jan 1, 1946

Frank 11. Probert, Neudorf, Anhalt, Germany (communication to the Secretary): I have read with much pleasure Mr. Collier's valuable paper. But the system of timbering which he describes as used in the levels, stopes, etc., though it must be admitted to be very strong and safe, seems to me somewhat extravagant. The amount of timber required every month for such a system must be enormous; and only where suitable material could be cheaply obtained would such a plan be economically practicable. The first point which strikes me is the unusually great diameter of the timber employed. In the mines of Pfaffenberg and Meiseberg, which are under my supervision, the country-rock consists of argillaceous slates, traversed by innumerable small fissures or joints, dipping at all angles and striking to all points of the compass. Undoubtedly, this net-work has been caused by the upheaval of granite masses in the vicinity. Each fissure is accompanied by a more or less well-c1efinc.d gouge or fluccan, caused by the rubbing together of the slates at or after the original disturbance. In such

Jan 1, 1900

By Gordon I. Gould

The treatment of quicksilver ores to extract the metal, for centuries one of the fundamentally simpler metallurgical operations, has undergone few if any material changes during the past iew decades other than improvement and change of type of equipment used. Of almost universal application and as the seldom deviated from process, the roasting method is still considered superior to chemical metallurgy. Likewise, roasting of the crude ore without previous beneficiation continues to be standard practice, although some successful operations have employed concentration prior to roasting. The roasting process has been carried out in a variety of equipment, devised for different tonnage capacities, to treat "special" ores, and to satisfy an inventive notion of the particular builder, but during the past 25 years there has been one outstanding change in roasting equipment. This change, though neither originating in nor confined to the United States, has probably been developed and applied to a far greater extent in this country than in any other mercury-producing country of the world. The change from manually or gravity operated furnaces, mostly huge brickwork affairs justified largely by simplicity, lack of power and mechanical requirements, and occasionally by excellent metallurgical results, to mechanical furnaces, began actively during World War I under the stress of requirements for in- creased production, a shortage of labor, 2nd other factors to be brought out later. During the twenties the change to mechanical furnaces became nearly complete at American mines with the development of several types, the rotary furnace predominating. During the thirties, and the period of low prices in the early part of this period, few changes were made other than mechanical improvements and an almost complete acceptance of two types: the rotary furnace and the hearth or Wedge furnace. These two types have been developed to a high degree of metallurgical efficiency, have proved to be mechanically simple and have far greater flexibility and lower operating costs than pre-World War I furnaces. Of the two types the rotary is the more popular, about 30 rotaries having been in operation in the United States in 1943 as compared with about six hearth-type furnaces. The units of smaller capacity for roasting mercury ores have almost without exception been indirectly fired, such distinction being commonly accepted as the difference between retorts and furnaces, which are fired directly. The difference between indirect and direct firing obviously permits of quite different conditions surrounding the ore being roasted in relation to the chemical reaction to take place. In the indirect-fired unit the ore is contained within the body of the retort in a stagnant if not completely oxygen-impoverished atmosphere. In the direct-fired furnace the ore is in contact with the gases of combustion, which may easily (if not too easily) be supplied with an excess of

Jan 1, 1944