Search Documents

By S. R. Gilbert, B. W. Burdett, L. B. Hales

INTRODUCTION Grinding control is currently the most publicized control subject in the minerals industry. Flotation control and crushing control have not as yet received the widespread attention that grinding control has. The primary reasons for this center around the high capital costs of grinding equipment and the fact that grinding mills are extremely energy inefficient. In a typical copper concentrator the energy requirements to produce refined copper are: (1) [Total Energy Distribution (Kw-hr/yr)% Mining4.93 x 10817.3 Mineral Processing9.63 x 10833.8 Smelting and Refining13.9 x 10848.9] One-third of the total energy used for copper production is for mineral processing. A breakdown of this energy into process steps yields the following: [Total Energy Distribution (Kw-hr/yr)% Crushing and Grinding 7.16 x 108 73.8 Flotation 0.76 x 108 7.8 Materials Handling1.78 x 10818.4] It is apparent that comminution operations consume the largest proportion of the energy for processing and as such become major targets for improvements in efficiency. Unfortunately, size reduction operations are extremely inefficient. Efficiency calculations for grinding range from less than 0.1% to about 5% depending on the evaluation criteria. Because of these facts, grinding control has been and will continue to be the focus of major process control efforts. OBJECTIVES AND BENEFITS All benefits achieved as the result of grinding control are derived from modifying physical parameters which improve the efficiency of the grinding mill. These parameters include:

Jan 1, 1982

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By Robert E. Tally

CHAUNCEY L. BERRIEN, Butte, Mont. (written discussion).-Having had much actual experience with mine fires which have occurred or have been active in the mines of the Anaconda Copper Mining Co. during the past 4 years and having lately visited the fire zone of the United Verde mine with Mr. Tally, I wish to congratulate him for the success which he has had in controlling this fire and making the mine perfectly safe .for his miners. By this work he is not only keeping the property in operation but is reclaiming many lost orebodies. The ventilation system as described by him is practically the same as that used under my direction at the Mountain View mine fire in Butte in 1913 and at the Pennsylvania fire in 1916. This same system is at present being followed at the Leonard mine to extinguish a fire which has been active for 10 years although bulkheaded. The mining system in the Butte mine, at the origination of these fires was the same as that at the United Verde, namely, square setting .accompanied by the use of much timber bulkheading in the stopes owing to heavy ground. The pyritic content of the ore in Butte is not as high, but on the whole conditions have been the same, with the exception of actual location of the fire in the mine. I agree with Mr. Tally that flooding, the use of C02 or any gas, and the use of steam are all impracticable unless the fire zone can be absolutely sealed. His system of upcast escapement shafts in the fire zone, the use of bulkheads and fans to keep the gases away from the firemen, must be resorted to. By the method lie describes actual stoping may be carried on safely if started from the bottom of the fire and if the fire zone extends to the surface. In other words, the fire zone must be isolated from the rest of the mine by bulkheads and solid ground, with no ground above which can be damaged by spread of fire or caving. The serious fires in Butte have .occurred on or between levels in the mines where it was necessary to prevent their .extension upward, downward and laterally while the work of actually extinguishing them was in progress. This necessitated proper bulkheading should we lose control of the fire, the installation of ventilation similar to Mr. Tally's and the systematic drilling of holes with diamond drills for distributing water on the fire and around it.

Jan 12, 1916

By C. M. Weld

Attention has been turned recently to the exploration and development of certain large blanket-deposits of brown iron-ore in Cuba. The most conspicuous of these to-day, and the one upon which the most light has been shed, is the Mayari deposit, situated about 15 miles south of Nipe bag. Here the Spanish-Aniericau Co. has sole control over 18,500 acres of ore-bearing lands, reported by its engineers to contain 500,000,000 tons of ore. The necessary plant and equipment, with docks and railways, is now under construction for the early marketing of this ore. A similar deposit, and undoubtedly the next to be exploited, is the ore-field at Moa bay, where from 13,000 to 15,000 acres of ore-lands, immediately adjacent to the shores of an excellent harbor, have been generously covered by numerous mining-claims, practically all controlled by four large interests;. This deposit is now estimated to contain approximately 350,000,000 tons, on the basis of dried ore ready for shipment, a figure which may be increased when the western limits of the ore-deposit have been more accurately defined. Other deposits of the same type, but smaller and less accessible, are those at Cubitas, situated from 12 to 15 miles north of Camaguey city,

Jan 1, 1910

By M. G. Nicholas

The influence of deformation, relative movement and surface cleanliness on the strength of room -temperature "interparticle" bonds between copper surfaces has been studied. No bonding resulted when clean surfaces were merely pressed together, even under pressures of 50,000 psi. Bonding resulted, however, when clean surfaces were simultaneously pressed and moved relative to each other, some bonding occurring no matter how small the pressure or relative movement. Exposure of the clean surfaces to various chemicals inhibited bonding, none at all being produced by small relative movements. The size of the movements which first produce bonding between exposed surfaces depends on the nature of the chemical, being less than 0.002 in. for cleansing reagents and greater than 0.004 in. for lubricants, water and hydrogen sulfide. It is concluded from the experimental data that the prime requirement for bonding is the dispersal of surface films such as oxides and adsorbed contaminants. THE formation of interparticle bonds during the room-temperature compaction of powder metallurgy components greatly increases the ease of handling in subsequent production operations prior to sintering. The strength of unsintered compacts follows the same general trends as their density and hardness, but quantitative data are extremely Scarce. Quantitative correlation of the data on the overall strength of a compact with that of the individual interparticle bonds is virtually impossible due to the extremely complex geometry of powder compacts. Qualitatively, however, the strengths of unsintered compacts can be correlated with variations in parameters known to influence the extent of cold bonding, and hence interparticle bonding, such as surface cleanliness, relative movement, and deformation of the mating surfaces. Kuzmic and seelig4 found that contamination of powder particle surfaces with lubricants reduced the strength of unsintered iron and copper compacts. Interparticle shear has been shown to promote bonding by Train and Hersey7 while Gregory has shown that die rotation is beneficial. Eilender and schwalbe6 concluded that most bonding occurred during the early stages of pressing iron powder compacts when interparticle shear is one of the principal processes occurring. mile there can be little doubt that these and other factors, such as particle size and shape, affect the extent of interparticle bonding produced by compaction, evaluation of the influence of individual factors is not easy. Particle deformation and relative movement, for example, occur simultaneously during compaction, making any precise measurement of their relative influences difficult. Because of these and other difficulties encountered in studying interparticle bonding in actual powder compacts, the approach adopted in this study was to

Jan 1, 1963

By F. Cadena, Fred C. Bond, Walter L. Maxon

Grinding is one of the major problems in present-day milling practice, and in many cases, it represents one of the main items of expense. It becomes necessary from time to time, to compare grinding practice in one plant with that in another plant, and in making such comparisons, it would be very desirable were there available accepted standards of grinding resistance for the materials involved. Such a set of grinding constants would also be of considerable value in planning new grinding installations. There have been some tests published, notably those of Lennox,' which have been generally cited as a basis for such comparisons. Most of the tests made have been based upon open-circuit grinding, in which a weighed sample of the ore was crushed to pass a certain mesh, and was then ground under certain conditions, either wet or dry. Grinding was continued until a certain desired fineness was attained, and the comparisons based on the grinding time, or the samples were all ground for a certain specified length of time and comparison based upon the screen analysis of the products. Such methods have been acceptable where the ore was to be ground in open circuit. However, in modern milling practice, many grinding problems involve closed circuits wherein the oversize returns to the mill and a large circulating load builds up. A method of testing that does not take the circulating load into consideration might yield results quite different from those to be expected in practice, because the minerals in the ore that offer maximum resistance to grinding will accumulate in the circulating load up to an equilibrium value. Thus the nature of the ore charge in the mill at any instant may differ greatly from that of the new feed, with a consequent error in the rate of grinding determined by such a method. For example, let it be assumed that an ore to be tested consists of equal parts of difficult grinding mineral and easy grinding mineral. This is to be compared with an ore used as a standard, and consisting of minerals which are all of about the same grindability. If a comparison

Jan 1, 1935

By K. J. McGrew, J. W. Murphy

Introduction Maximization of profit consistent with environmental protection is the principal goal of new applications development for any conventional or in situ mining technique. Efficient evaluation of all the parameters that contribute to mining costs and production hinges on proper design and evaluation of testing programs and data. The program discussed uses several field and laboratory procedures to estimate ore deposit characteristics and optimize lixiviant compositions. Ore characteristics and lixiviant compositions are then used in a long path leaching test (stream tube test). Stream tube test data are analyzed by mathematical models with computer assistance to predict such wellfield rate parameters as target metal production, lixiviant consumption, and restoration. When these predicted rates are combined with market values for target metals, capital expenditures, prices of lixiviant chemicals, and other economic variables (labor costs, power rates, and licensing fees), an assessment of the relative feasibility of various proposed mining plans is possible. The flowsheet in Fig. 1 illustrates this process. [ ] Field and Laboratory Procedures In general terms, the procedures followed in the evaluation of an in situ leaching application aim at accomplishing: •rapid leaching and maximum recovery of the target metal in a marketable form, •low consumption of lixiviant chemicals, •unquestionably satisfactory restoration of the mined aquifer, and •minimization of capital and operating costs for the above through development of an optimum mine plan. Keeping these goals in mind, the following minimum test program is generally recommended. Geology •Estimate of ore reserves and their variability. •Average disequilibrium value for uranium deposits. •Ore thickness, depth to ore, water level, degree of confinement, and consolidation. •Characterization of quality and quantity of other ore deposit constituents (e.g. sulfide minerals, ion exchange parameters). Hydrology •Single well pump and injectivity test. •Downhole vertical permeability test to compare flow rates of barren and mineralized formations. •Groundwater quality as it may affect licensing, hydro metallurgy, and restoration. Hydrometallurgy • Flask or autoclave tests for optimization of lixiviant parameters and determination of specific reaction rate constants. • Flask or autoclave tests for assessing amenability of lixiviant solutions with ore, consumption of lixiviant, stability of metal in solution contacting ore, and environmentally important species mobilized. • A long-path leach test for modeling the behavior of the lixiviant solution flowing through a long mineralized streamline (stream tube testing). •Metal recovery tests from lixiviant solutions (ion exchange, electrowinning, etc.). •Lixiviant regeneration tests. •Environmental restoration tests.

Jan 1, 1985

By J. S. Seawright

Haulage is a costly feature in the operation of an open pit mine, whether it be iron, copper, or limestone. The National Iron Co. has adapted an old underground method to the open pit inclined skip haulage to bring the ore from the pit bottom to the crusher or beneficiation plant. The Rockover skip has been placed in operation where limited areas have retarded or eliminated use of long rail or road slopes. Deep and narrow orebodies subject to rapid increase in depth that discourage use of conveyor belts and necessary crushing plants are ideal for this system. The skip haulage method was developed to combine the desirable features of conveyor, truck, and rail haulage and at the same time avoid the draw- backs. The skip was designed to follow the natural angle of repose of the pit wall and can vary from 25° to 45°. Open-pit skips now in operation show that the installation is successful and provide the

Jun 1, 1955

By Joseph Cervik

INTRODUCTION Common methods of controlling gob gas in U.S. mines are by means of ventilation of gob areas and gas drainage through surface boreholes. Costs of drilling surface gob holes increase as deeper coal- beds are mined. Where gob holes cannot be drilled because of topography, ventilation is the only means of control. Even then, sufficient air may not be available to dilute methane in the bleeder entries to acceptable levels. Thus, new methods of gob gas control need to be developed that are independent of surface topography, and of the mine ventilation system, and less costly than present systems. Except for slight variations in procedures and equipment, Great Britain, West Germany, France, Belguim, Poland, and Czechoslovakia use a common methane control method that is different from the system generally used in the United States. This Bureau of Mines paper reviews European mining methods, mining conditions, and methane control technology and discusses their applicability to U.S. mines.

Jan 1, 1981

In high-volume mining operations, preventive maintenance programs that include standardized replacement wear parts can boost equipment availability and lower unit costs. Meeting the daily production targets depends heavily on keeping equipment working as close to full time as possible. This is the case at one medium-sized western surface coal operation producing approximately 2.7 million t/y (3 million stpy). The mine, located in western Wyoming, removes in excess of 8 million m3 (10.5 million cu yd) of highly abrasive overburden each year. According to the mine superintendent, "Abrasion at this mine is some of the worst I've ever seen. Shovel points can wear out in little more than one shift. Dozer blades some- times last two weeks, but can wear out sooner. And ripper points really take a beating. If we can replace this fast-wearing iron with small pieces that go on quickly, we think that's the way to go."

Jan 3, 1978

By S. Feuerstein, L. Rice

The effect of low pressures on the flow and fracture behavior of molybdenum is described. For poly crystalline samples, room-temperature tensile tests indicate greater ductility under 10 Torr than under intermediate pressures up to and including atmospheric pressure (760 Torr). In addition, tests conducted at 760 Torr under atmospheres of air, dry nitrogen, and purified argon exhibited no apparent difference in mechanical properties. Critical tests involving baking in situ as well as those involving single-crystal deformation further imply that the ductility effect is a pressure-dependent phenomenon related only to the fracture process. This dependency is discussed in terms of adsorption and diffusion contributions. THE effect of very low pressures on material properties has heretofore been presumed to be important only for substances possessing relatively high vapor pressures at ambient temperatures. Research has therefore been concentrated primarily on organic solids and liquids, and in some instances on metals such as zinc and cadmium. Most vacuum-effect studies' on the mechanical behavior of metals have been performed under conditions of either cyclic loading or creep rupture at elevated temperatures, i.e., over extended time periods. These studies were not restricted to high vapor pressure materials but also encompassed such metals as gold, copper, and nickel. Very little concern, however, was placed upon the importance of a vacuum environment on the mechanical behavior of metals subjected to a simple unidirectional deformation at ambient temperatures. A tension test is generally of short duration as compared to a creep test, and at room temperature vacuum effects if any would be expected to be surface-limited. In early 1963, Kramer and podlaseck2 reported a change in the bulk flow behavior of aluminum single crystals during room-temperature tension tests. The deformations were performed under pressure conditions of 760 to 3.4 X 10-8 Torr and indicated for the first time a vacuum surface effect contributing to the bulk tensile behavior of metal specimens. As a consequence, an experimental program was initiated in this Laboratory to study the effects of ultrahigh-vacuum conditions on the mechanical behavior of metals. The results of a preliminary study on poly-crystalline molybdenum3 revealed, unlike Kramer's observations of changes in the stress-strain behavior, only an increased ductility under ultrahigh vacuum. Flow behaviors were nearly identical for all tests re- gardless of pressure. This paper presents comprehensive results obtained in this area of research. 1) EXPERIMENTAL PROCEDURE Three material categories were used in this study: sintered and are-cast polycrystalline molybdenum of nominal purity 99.93+ pct and single-pass electron-beam zone-refined molybdenum single crystals having a nominal purity level of 99.99+ pct. The interstitial levels (weight percent) as determined by the Materials Testing Laboratories, Division of Magnaflux Corp., were as follows: sintered molybdenum (C— 0.005, H—0.0004, O—0.015, N—0.008); and arc-cast molybdenum (C-0.0038, H-0.0003, O-0.015, N-0.023). Single-crystal molybdenum obtained from Materials Research Corp. had a typical interstitial analysis of C-0.0015, H-0.00007, O—0.00045, and N-0.0001. Tensile specimens having a 5 mm diam by 50.8 mm length were prepared from these materials. An average grain diameter of 0.059 mm was obtained for the sintered specimens following a 4-hr, 1600°C heat treatment. Grain sizes from 0.019 to 0.149 mm were obtained in the arc-cast specimens following heat treatments from 1100° to 1600°C for 1 hr. This series of specimens was used exclusively for the grain-size effect studies. All samples were electrolytically polished in 97 pct sulfuric acid solution prior to testing. Experiments were performed at room temperature in an ion-pumped ultrahigh-vacuum system positioned in an Instron tensile machine, Fig. 1. A constant strain rate of 4.2 x 10-4 sec-1 as derived from crosshead displacement was assumed for the deformations. Starting vacuums ranged from 2 to 0.5 X 10-10 Torr. These pressure measurements were made using corrected values4 of an NRC Redhead gage. Comparative readings were also made against a G.E. triggered dis-

Jan 1, 1967

By D. H. Desy, L. C. Fincher

The magnesium-rich end of the Mg-Ti phase diagram was investigated. The liquidus, solidus, and solvus boundaries to 1 pct Ti were established. All alloys were prepared by saturating molten magnesium with titanium in a consumable titanium crucible under inert gas maintained at 230 psig. The liquidus of the Mg- Ti system was determined by analysis of dip samples taken from 700° to 1300°C under equilibrium conditions in a pressurized inert atmosphere furnace and by analysis of small ingots rapidly poured and quenched from 1400° to 1500°C. The solubility of titanium in magnesium ranged from 0.018 wt pet Ti at 700°C (0.012 wt pet at 650°C by extrapolation) to 1.035 wt pet Ti at 1500°C. The solidus for compositions ranging from 0.03 to 1.00 wt pet Ti was determined to be 650° ± 1°C by thermal analysis. The titanium solid solubility values ranged from 0.08 wt pet at 350°C to 0.19 wt pet by extrapolation to 650°C. The freezing reaction is peritectic. No intermetallic compounds were found in the system; the phase in equilibrium with molten magnesium saturated with titanium was found to be titanium with magnesium in solid solution. Solid titanium will dissolve at least 1.32 wt pct Mg. PREVIOUS investigations of the Mg-Ti system have shown considerable disagreement on the solubility of titanium in liquid magnesium. Furthermore, the solid solubility of titanium in magnesium has not been well established. Liquidus curves for previous work and for the present investigation are shown in Fig. 1. Aust and Pidgeon1 used a dip-sampling method on molten magnesium held in equilibrium with solid titanium under a protective atmosphere to determine the solubility and found that it ranged from 0.0025 wt pet Ti at 651°C to 0.015 wt pet Ti at 850°C. Eisenreich2 introduced titanium into molten magnesium by means of TiCL4 adsorbed on BaCl2. Ingots were then cast at various temperatures. Making the assumption that only the titanium dissolved in magnesium at the time of casting was soluble in H2SO4, Eisenreich determined the solubility of titanium in molten magnesium to range from 0.003 wt pet at 655°C to 0.115 wt pet at 800°C. Eisenreich also determined the solid solubility of titanium in magnesium to be 0.015 wt pet at room temperature and 0.045 wt pet at 500°C. Since the solid solubility just below the freezing temperature for the bulk of the alloy was much larger than the liquid solubility just above the freezing temperature, Eisenreich concluded that the freezing reaction was peritectic. Obinata et al.3 equilibrated molten magnesium with titanium in hermetically sealed titanium containers which were then furnace-cooled. The titanium content of the magnesium was then determined and found to range from 0.170 wt pet at 700°C to 0.85 wt pet at 1200°C. No intermetallic compound was found in the system. The Armour Research Foundation4 determined two points on the solvus by electrical resistivity methods: 0.00057 wt pet at 200°C and 0.0008 wt pet at 300°C. At higher temperatures, data were meaningless with no trends observable. The authors of this report believed that the lack of significant data at the higher temperatures was due to variations in specimen geometry, although there was no positive evidence to verify this supposition. The present investigation was undertaken to clarify the uncertainty in both the liquidus and solvus of the magnesium-rich end of the Mg-Ti system. EQUIPMENT AND MATERIALS The equipment used in this investigation, with some modifications, was essentially that used by Crosby and Fowler5 in their determination of part of the Mg-Zr phase diagram. The equipment, as modified for this work, is shown in Fig. 2. It consists of a sealed furnace chamber which can be pressurized with inert gas so that melts can be made above the boiling point of magnesium at atmospheric pressure. Melts are made by induction heating in a titanium crucible which, after diffusion of sufficient magnesium into the walls of the crucible to saturate the titanium at the sampling temperature, comprises the solid phase in equilibrium with the molten magnesium. Dip samples may be taken with the sampling tube, or the entire furnace may be tilted so that ingots may be poured into a mold in the side chamber. The principal difference from the earlier apparatus is in the thermocouple, which in the present equipment is enclosed in a protection tube and immersed directly in the melt. The tips of both the thermocouple protection tube and the sampling tube, which dip into the melt, are made of high-purity titanium. The 4 1/2-in.-long titanium tip of the sampling tube is threaded into a steel tube, O in Fig. 2, which extends through the top of the furnace. To determine whether the temperature at the tip of

Jan 1, 1969

By Andrew Hyslop

In our never ending search for new and better ways of underground mining, we find that transportation has had its share of new ideas in the past few years. The old and still effective method of track haulage has had some competition from rubber-tired cars and belt conveyors, each of which has its own safety hazards which demand close scrutiny in any safety study. The use of shuttle cars, in particular, has introduced clearance hazards caused by the absence of the more or less positive guides formed by the rails of a track sys- tem; likewise the requirement of greater clearance tends to increase roof hazards which we all know to be great enough with the best of methods. However, the subject of transportation hazards is too broad to be covered entirely in one paper, so I will confine myself to track methods which carry the preponderance of underground tonnage. I am quite sure that to this group it is an evident fact that haulage accidents are of major importance. However, to stress the point, it may be well to look at a few figures. Safety statistics can be quite boring and often are subject to question as to mathematical accuracy because of different

Jan 1, 1949

By C. D. Williams, C. E. Ells

The susceptibility of quenched and aged Zr-2.5 wt pct Nb alloy to embritt2ement during irradiation has been examined for a number of solution temperatures and aging times. Material quenched from temperatures approximately 40°C below the transus has high tensile ductility, and this ductility is insensitive to aging at 500°C or to irradiation. If, however, the material is quenched from temperatures above the transus it becomes highly susceptible to loss of ductility either from aging at 500 or from irradiation. Inter granular failure is characteristic of the materials having low ductility. The distribution of the equilibrium phase is found to control the susceptibility to embrittlement by restricting 6 grain growth during heat treatment and thus influencing crack propagation. IN zirconium, as in titanium, -stabilizing alloy additions are used to obtain high strengths via quench and age heat treatments, and the Zr-2.5 pct Nb alloy has been developed1 because of its strength advantage over the Zircaloys. Early in the development of the Zr-2.5 pct Nb alloy the problem of 13 embrittlement was appreciated, and for this reason the solution temperature was chosen below the p transus.' In the course of irradiation studies on quenched and aged Zr-2.5 wt pct Nb alloy it was found' that irradiation introduced an important aspect of p embrittlement, riz., material quenched from the phase and aged 24 hr at 500°C was severely embrittled by moderate doses of neutron irradiation. This effect had not been studied in titanium alloys. In titanium the metallurgical features leading to 0 ernbrittlement were found to be structures with: a) coarse a platelets at the grain bondaries, b) finely dispersed a uniformly distributed throughout the (0) matrix,6 c) Widmanstatten a-13 with more than 50 pct P, d) the presence of some metastable p transformation products,3 and e) large prior -phase grain size.5 Alternatively, the presence of a uniform distribution of coarse a was conducive to high ductility and a structure largely of equiaxed a was very dctile. The detailed mechanisms of the embrittlement have not been worked out for all of these conditions, although weakness at either a-matrix boundaries or prior p grain boundaries have been prominent in the eculation. It was proposed that acicular a might act as a mild notch, and low ductility has been associated with easy fracture along its boundary.' There have been two opposing suggestions for the source of the high ductility associated with equiaxed a phase. JaffeeB proposed that this a would accept a large por- tion of the oxygen, thus increasing the ductility of the matrix, whereas after study of a Zr-Nb-Cu alloy Weinstein and oltz proposed that the a phase, softer than the martensitic matrix, acted to blunt cracks formed in the matrix. In the present work we have studied the effect of neutron irradiation on the ductility, particularly the P embrittlement, of the Zr-2.5 wt pct Nb alloy. By a variation of solution temperature and aging time a variety of metallurgical conditions have been examined, and a range of resultant ductilities obtained. The ductility has been related to the material microstructure and mode of fracture. EXPERIMENTAL The alloy used in the present work came from two separate ingots fabricated into rod of 3/8 or i in. diam, Table I. For both batches the P transus temperature was approximately 890° C. Most of the heat treatments were done directly on lengths of the j} in. diam rod, after which the tensile test specimens were machined. Quenching was achieved by dropping rods from a dynamic vacuum into water, the cooling rate estimated to be 2 100°C per sec. For aging the rods were encapsulated in evacuated silica tubes. Round tensile test specimens, with gage diam and length 0.160 and 1.0 in., respectively, were used throughout and pulled at room temperature or 300°C on Instron tensile machines, at a crosshead speed of 0.05 ipm. Specimens were irradiated in the NRX and NRU reactors, in facilities described in previous publications.'0 The metallurgical conditions examined have been: All tensile test specimens were machined with axes in the axial direction of the swaged rod. Although the specimen had a degree of preferred crystallo-graphic orientation with basal plane normals both parallel with and perpendicular to the tensile axis, the material was comparatively isotropic." The techniques of thin foil examination in the electron micro-

Jan 1, 1970

By L. Delisle

This work represents the first step of an attempt to test the applicability of the electron microscope to the study of subgrain structures in copper. Observations on annealed and deformed single crystals and polycrystalline samples of copper are described. IN the course of study of the structure of fine tungsten wires and tungsten rods with the electron microscope, well defined subgrain structures were observed. The size, size distribution, and orientation uniformity of the etch figures varied widely in different samples. Figs. 1 and 2, electron micrographs of a tungsten wire and of a tungsten rod, respectively, are illustrations of the difference in size and size distribution of the etch figures in different samples of the same metal. The observed differences, as pointed out in a previous paper,' appeared to be related to the heat and mechanical treatments of the samples. They were also consistent with the results reported in the literature on the mosaic structure of metals.' For that reason a program of research was initiated in an effort to obtain more systematic evidence of the possible relation of heat and mechanical treatments to the subgrain structure of metals as observed in the electron microscope. The purpose of this paper is to present observations made on the effect of cold work on the subgrain structure of copper. Procedure Starting Materials: Copper was the metal studied because it can be obtained in a high degree of purity, much information is available in the literature on its properties and its response to cold work and heat treatment, it shows no allotropic change, and it is sufficiently hard to be handled without great difficulty. Two groups of specimens were used: 1—single crystals cast from spectroscopically pure copper and 2—polycrystalline samples of oxygen-free high conductivity copper. Single crystals were studied because it was hoped that the elimination of a number of variables, such as grain boundaries, orientation differences, degree of purity, would simplify the problem and perhaps permit a better understanding of the phenomena that would be observed. The polycrystalline samples were designed to give a general picture of the changes considered. The single crystals were made of copper which analyzed spectroscopically to better than 99.999 pct Cu. They were cast in vacuum, by the Bridgman method, in crucibles made of graphite with a maximum ash content of 0.06 pct. The mold design is shown in Fig. 3. It permitted casting crystals of the size and shape required for the experiments, so that the danger of introducing cold work in the original samples by cutting or other machining would be eliminated. The polycrystalline samples were pieces, 3/4 in. long, cut from a rod of oxygen-free high conductivity copper, % in. in diameter. A flat surface, 1/4 in. wide, was milled along the rods, polished, and etched. The samples were then annealed in vacuum at 850°C for 1 hr. Polishing and Etching: Work previously done on tungsten,' polished mechanically and etched chemically," had shown that: 1—the general appearance of the etch figures of a given sample was not altered by repeated polishings and etchings under similar conditions; 2—variations in the time of etching and the concentration of the etchant changed the definition of the etch figures, but did not alter their general size nor orientation distribution within the limits of observation. Further work confirmed the reproducibility of the subgrain structures observed in, 1—single crystals and polycrystalline samples of copper when polishing and etching were repeated under similar conditions, and 2—specimens of tungsten and polycrystalline copper when electrolytic polishing and etching were substituted for mechanical polishing and chemical etching, respectively. On the strength of these observations, it was felt that, if conditions of polishing and etching were kept constant, changes observed in the subgrain structure of a sample upon deformation and annealing would be attributable to such treatments. For that reason the conditions of polishing and etching were kept as constant as possible. The single crystals were polished electrolytically in a bath of orthophosphoric acid in water, in the ratio of 1000 g of acid of density 1.75 g per cc to 1000 cc of solution, under a potential drop of 1.6 to 1.8 V. Electrolytic polishing was selected to prevent the formation of distorted metal in polishing. The same samples were etched by immersion in a 10 pct aque-

Jan 1, 1954

By Rogers Wade

THE Pilares mine of the Moctezuma Copper Co. is situated at Los Pilares de Nacozari, Sonora, Mexico, about 75 mi. (120.7 km.) South of the international boundary and about 7 mi. (11.26 kin.) east of the town of Nacozari de Garcia. It is situated at an elevation of 5000 ft. (1524 m.) in one of the northward trending ridges that form part of the mountain mass that culminates in the Sierra Madre de Mexico. To the east, south, and west, the topography is rugged and diversified; to the north less diversity exists, ranges of mountains rise sharply out of almost level ground and give the basin range structure characteristic of the southwest. The climate is dry, the average rainfall of 15 in. (38 cm.) being confined almost entirely to the months of June, July, and August. The

Jan 8, 1919

At its meeting on June 22, 1950, the Board of Directors passed a resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters On June 23, 1959 the Board of Directors made minor revisions in the resolution to bring it up-to-date with recent changes in the Institute's structure The revised resolution IS as follows

Jan 1, 1960

By N. B. Pilling

The deleterious effect on the mechanical properties of copper, re-sulting from heating in contact with reducing gases, is well known, but the mechanism of the action does not appear to have been definitely established. The purpose of the present investigation was not to determine the exact variations in physical quality of commercial copper, with its various impurities, as dependent upon the composition of the gas, temperature of exposure, etc., but rather to study the nature of the action and the conditions under which it occurs. The physical result of the so-called "gassing" of copper has been generally described as the development of "brittleness." There appears to be a striking decrease in tensile strength, associated with a considerable loss of ductility, and a small copper strip or wire affected in this way can be snapped in two when bent. Larger articles may have an outer layer alone affected, which can be detached from the core by hammering or bending. Perhaps the earliest reference to this subject is that of Heynl in 1900, and among the later observers may be mentioned Archbutt,2 Bengough and Hill,3 Johnson,4 Mathewson and Thalheimer,5 and Ruder.6 Bengough and Hill, while working with arsenical copper, were the first to suggest the possibility of the formation of gases within the copper itself, while Ruder endeavored to explain the action by the reduction of the

Jan 1, 1919

By Thos Stroup

RECENT contributions to the literature relating to the problems of coal mine management have discussed the pros, and cons of unionism among the miners as bearing upon the immediate problems of the industry, but have devoted singularly little thought to the underlying causes, and the fundamental reasons. for the remarkable growth of union sentiment among the miners, a growth paralleled only in the case of the railroad workers. It is all very well to revile their organization, its obvious stupidity and stubbornness, its multitude of economic and social crimes, but it is also well to realize that there have been deep-seated causes for all these things, causes that, while operating in all industries and amongst all workers, have in none of them found the optimum conditions for development such as exist in the coal mining industry. The rise of the United Mine Workers of America to a position of importance in the industry synchronizes roughly with the introduction of short-time operation; of course seasonal shutdowns and slow-time working have always been evident in our bituminous fields, but these evils have grown steadily worse since 1895 and the U. M. W. of A. has grown steadily stronger; yet short-time operation alone cannot account for this tremendous growth for, witness the signal failures that have always attended the attempts to organize the harvest workers, the fruit packers and other highly seasonal workers.

Jan 9, 1923