Search Documents

GEO. F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).-In this exposition of experimental data, the author infers, indirectly at least, that by the Charpy test information was obtained that led to the improve-ment of certain ordnance parts and that this improvement could not have been attained without the Charpy test. On examination of the data, however, it appears that the important point of the whole matter was that while the material had been accepted from the results of longitudinal tensile tests, it was really transverse ductility that was desired. The writer has no desire to attempt to detract from the value of the paper or to discredit the Charpy test in any way, but he would like to ask the author if he will not give more clearly his reasons for preferring the Charpy impact test for investigational and control work of this kind, over the more usual tensile test made in a transverse direction. The tensile test pieces are more cheaply made than the square notched impact bars; and from the former the limit of elasticity and the ultimate strength as well as, the ductility are obtained, while in the Charpy test only one property is measured. It does not seem that the author has shown a sufficient reason for favoring the latter test, when both it and the trans-verse tensile test served his purpose equally well in indicating the proper metal and treatment required for his special forging, and it is hoped that this reason will be given more clearly as a matter of useful general information.

Jan 11, 1919

By N. S. Stoloff, M. Gensamer

The effects of temperature, grain size, and magnesium content on the strength and ductility of cadmium were studied in the range -269° to 23 °C. A sharp drop in ductility between -140° and -190°C marked a transition in fracture mode from ductile shear to inter gvanular fracture. The addition of up to 15.35 wt pct Mg in solid solution raised the transition temperature, and for two compositions produced basal cleavages. The relatively high ductility of unalloyed cadmium at cryogenic temperatures is attributed to temperature independence of the yield stress and the absence of dislocation locking. ALTHOUGH numerous studies have been made of the mechanical properties of cadmium single crystals,1-5 no comprehensive investigation of deformation and fracture in polycrystalline cadmium has been carried out. This investigation was initiated to determine the mechanisms of deformation and fracture in polycrystalline cadmium, and to attempt to correlate these mechanisms with the behavior of other metals of hexagonal close-packed structure. A second objective of this work was to determine whether the slip systems and mode of fracture of polycrystalline cadmium could be altered by reduction of the axial ratio, which is 1.886, through alloying. Dorn and co-workers' have been able to induce prismatic slip in magnesium through alloying to reduce the axial ratio. Single crystals of cadmium are so highly ductile that glide strains of 400 pct are observed at room temperature, and 80 pct at -269°c.l Failure in every reported case is by necking down and shearing off of the crystal. Cleavage in cadmium single crystals has never been observed. Magnusson and aldwin reported a ductile to brittle transition for polycrystalline cadmium at about —160 C for specimens tested at a strain rate of 0.05 in. per in. per min in tension. However, even at -196° substantial ductility was retained. The transition temperature was strain rate dependent, impact loading at 19,000 in. per in. per min raising the transition temperature to about -85°C while leaving the low temperature ductility unchanged. No information was given on microstructures or fracture mode, nor were stress-strain characteristics reported. In the present investigation, tensile tests were carried out on polycrystalline cadmium and solid solution Cd-Mg alloys to determine flow stresses, work-hardening behavior, fracture strength, and fracture ductility. Variables employed included temperature, alloy content (and c/a ratio), and grain size.Some compression data also have been obtained for comparison purposes. I) EXPERIMENTAL PROCEDURES A) Polycrystalline Cadmium. Two purities of cadmium were employed in this investigation. Cadmium of 99.95 pct purity was supplied by Belmont Smelting and Refining Co. Cadmium of 99.99+ pct purity was supplied by American Smelting and Refining Co. Threaded cylindrical tensile specimens were machined to give approximately a 1/2 in. long straight gage section with a reduced diameter of about 0.110 in. Specimens were heat treated in evacuated pyrex capsules in the range 140" to 290°C to produce desired grain sizes. All specimens were polished in a solution containing 320 g Cr03 and 20 g NaS04 in 1000 cc of H20. Occasionally this solution caused staining of the specimen, in which case a further polish with a solution of one part HN03 and two parts H202 in two parts ethyl alcohol was employed.' Tensile testing was carried out on a screw-driven Instron machine, at a constant rate of crosshead movement, which for most tests was 0.01 in. per in. per min. Load vs time, and therefore load vs total strain, were recorded. Temperatures from -196" to -40°C were obtained by passing nitrogen gas through a copper coil immersed in liquid nitrogen, and then feeding the gas into a jacket around the specimen. Tests at -269°C were carried out in a helium cryostat, at a crosshead rate of 0.1 in. per in. per min, with specimens of 1 in. gage length. Compression specimens were tested in a jig similar to one designed by ilman. The jig was mounted on the under side of the Instron crosshead. Load was transmitted by means of a rod connected to a movable part of the jig at one end, and the load cell at the other end. A downward movement of the crosshead applied a compressive load to the specimen.

Jan 1, 1963

By L. W. Bahney

Many methods for the determination of gold or silver, or both, in cyanide solutions have been published, which with care in manipulation, and modification in some cases, will give results that are satisfactory. It is possible to classify or group these methods as follows: 1. Evaporating the solution in a porcelain or agate-ware dish containing litharge,l or in a "boat" made of lead foil. 2. Forming a lead sponge containing the precious metals by means of zinc shavings,2 zinc dust,3 or a piece of aluminum.4 3. Decomposing the cyanide solution with an acid and precipitating the precious metals by the use of one or a combination of some of the following: Copper sulphate,5 sodium sulphite,6 hydrogen sulphide,' cement copper.ll 4. Precipitating the silver by zinc dust held in a Gooch crucible and determination with a standard solution of sulphocyanate.9 5. Electrolysis.l0 . 6. Colorimetry.ll

Jan 1, 1915

By John Birkinbine

(New Haven 'Meeting, February, 1909.) AWAKENED public interest in efforts to conserve natural resources will certainly be appreciated by the members of the American Institute of Mining Engineers, and a discussion upon conservation may well form a part of one of the Institute meetings, for the records of papers and discussions which appear in the 38 volumes of its Transactions are replete with evidence of effort's in this direction. Every process which reduces the fuel consumed or the power applied per unit of product; every utilization of waste material, or employment of that formerly rejected, to obtain something of value ; every feature of construction or operation which lessens the labor required or increases the output per employee, is an advance in the direction of true conservation. This may not appear from the records of late conferences or from published articles, in which the effort seems to be concentrated upon reducing the consumption and presenting to the people of the country estimates of exhaustion of natural resources. I rejoice in the awakening of public interest in a matter so important for the present and future welfare of our nation; I appreciate the possibility of much good following conferences of the Governors and delegates from various States and from national societies; and I recognize the interdependence, not only of different States, but of contiguous nations. In fact, the marvelous development of transportation by land and by water, and the decreasing rates at which commodities can be moved great distances, have in many cases practically obliterated geographical boundaries, and nearly every country on the globe can either market its product in other lands or draw upon them for raw or manufactured materials ; hence, conservation is an international subject.

Apr 1, 1909

By R. S. Dean

AMONG naturally occurring inorganic compounds, magnetite has many unusual and interesting properties, and it is the purpose of this paper to call attention to these properties and review possible uses of magnetite that might be based on them; in other words, to see what uses may be found for magnetite as a physical rather than as a chemical entity, as a mineral rather than as an iron ore. The Mineral Physics Studies initiated in the Metallurgical Division of the U. S. Bureau of Mines a few years ago gathered together much information on mineral properties, and they are therefore the principal source of material for this paper.

Jan 1, 1937

By B. M. Larsen

NEVER having actually tried to engage in the systematic education of anyone, and having little direct knowledge of the practical problems and limitations in the field of education, I can pose only as a "nonexpert" in this field, one whose ideas are to be regarded as personal opinions. The necessity for compromise between educational ideals and the practical limitations of time, money, and mental capacities of both student and teacher is evident in the preparation of an end product that we may regard with a reasonable degree of conviction as a professional engineer. We need to do so many things. The engineering student must have a clear understanding of the basic sciences; he should develop manual skills and co-ordination; he should speak and write the language with simple clarity and directness; he should gather knowledge of a special field; and, he should be educated for living in a broad ..

Jan 1, 1948

By Henry Engelmann

ORes are generally found in the mines mixed with more or less base matter, which renders their treatment by smelting or milling unnecessarily costly. They have to be sorted. Those of a higher grade remain often mixed with substances which might, with hardly a loss of metal and at small expense, be removed by dressing machinery, and a concentrated and purified ore thus obtained, which would bring a far higher price, because it can be reduced by cheaper methods, and, at any rate, at less expense, besides affording a saving of transportation, which in our territories is often an item of no small magnitude. The ores of a lower grade have often to be

By Henry Engelmann

ORES are generally found in the mines mixed with more or less base matter, which renders their treatment by smelting or milling unnecessarily costly. They have to be sorted. Those of a higher grade remain often mixed with substances which might, with hardly a loss of metal and at small expense, be removed by dressing machinery, and a concentrated and purified ore thus obtained, which would bring a far higher price, because it can be reduced by cheaper methods, and, at any rate, at less expense, besides affording a saving of transportation, which in our territories is often an item of no small magnitude. The ores of a lower grade have often to be

Jan 1, 1874

By J. K. Lovrien

A Link-Belt roller-bearing conveyor system was in- stalled recently at the Gross-Marble mine of the Oliver Iron Mining Co. at Marble, Minn., for removal of overburden and lean ore. The material, consisting of clay, sand, gravel, and glacial boulders. is excavated by an electrically operated walking dragline equipped with a 10 cu yd bucket working from a boom approximately 150 ft long. This machine loads into a receiving hopper of a rail-mounted screening plant in 45 second cycles. A manganese steel apron feeder under the receiving hopper delivers to an elliptical grizzly, from which the oversize boulders and extraneous material, by way of an apron conveyor, arc loaded into refuse haulage trucks.

Jan 12, 1951

By W. Rostoker, R. P. Elliott, B. W. Levinger

Phase equilibria in the Ti-Mn-Mo system have been investigated in the composition range 100 to 60 pct Ti and in the temperature range 550 to 1150°C. Three out of ten isothermal sections are presented as well as seven vertical sections, projections of the beta space and the surface of incipient melting. A STUDY of the system Ti-Mn-Mo was undertaken as part of a program to aid in the development of titanium-base phase equilibrium diagrams of potential technical importance to alloy development. The scope of the investigation included the composition range 100 to 60 wt pct Ti (all compositions refer to weight percentages) and the temperature range 550" to 1150°C. A surface of incipient melting was constructed from measurements of a large number of alloys. In the binary system Ti-Mo,' the high temperature modification of titanium generally spoken of as the p phase is stabilized to successively lower temperatures with increasing alloy content. There are no known intermediate phases, and complete miscibility exists between body-centered cubic titanium and molybdenum. The u solid solution is limited to less than 0.8 pct Mo at temperatures between 885" and 600°C. An equilibrium diagram for the binary system Ti-Mn has been published.' Manganese behaves as a p stabilizer but undergoes a eutectoid transformation at about 20 pct Mn and 550°C to a plus an intermediate phase. The structure of this phase has been found to be isomorphous with the a phase FeCr." Accordingly, the phase is assigned the formula TiMn, although its actual location on the composition scale has not been determined and may well be not exactly at the equiatomic composition. In disagreement with ref. 2, the origin of the TiMn phase has been shown' to be a peritectoid transformation at a temperature between 900" and 1000°C. A second intermediate phase occurs at the atomic proportions TiMn,. The structure of this phase was originally established by Wallbaum" as having a hexagonal lattice (C 14 type, 12 atoms per unit cell) isomorphous with MgZn,. In this work, the structure determination was confirmed and lattice parameters determined to be: a = 4.815 kX, c - 7.901 kX. Because of the extensive range of the P phase, the ternary system was suited to the determination of the phase boundaries by the parametric method of Andersen and Jette." During the course of the investigation, this method was found applicable only to the P/a+P boundaries but not to P/P+ compound boundaries. Metallographic methods were used alternatively for delineating these phase boundaries. Preparation and Treatment of Alloys Over 70 alloys were prepared for the study of this system. Ten gram alloy buttons were arc melted in a nonconsumable electrode furnace using inert atmosphere protection, and a water cooled copper crucible. The construction and operation of this type of melting unit has been described.' To insure complete solution of alloy additions, especially molybdenum, the buttons were remelted alternately on top or bottom as many as five times. This was accomplished by a suitable mechanism for "flipping" the ingots over. It was very difficult to obtain homogeneous melts in the region of less than 75 pct Ti because of the very high melting point of molybdenum and Ti-Mo master alloys and the comparatively low boiling point of manganese. Thus, the arc conditions for insuring complete solution of molybdenum were incompatible with the prevention of heavy losses of

Jan 1, 1955

By E. De Goyler

Volcanic origin was among the first of the theories advanced to account for the occurrence of the salt domes of the Gulf coastal plain, northern Louisiana, and eastern Texas, and it is still being re-stated in various forms by the most recent contributors to our knowledge of the geology of such deposits. Argument has been largely by analogy and attention has repeatedly been called to the Mexican oil fields, particularly those of the Tampico-Tuxpam region, because of the occurrence of oil in close proximity to volcanic plugs in those fields, an occurrence supposed to have some resemblance to the common occurrence of oil in the salt domes of the United States. The author, having spent several months of the past year in a general study of salt domes and in a detailed study of certain domes in the United States, and having been acquainted for some time with the exploration of similar domes in the Isthmus of Tehuantepec region, Mexico, and with the general geology of the Tampico-Tuxpam region, Mexico, has reviewed the various theories of volcanic origin for salt domes which have been advanced to the present time. The purpose of this paper is to present such review and to discuss the supposed Mexican analogy. Review of Volcanic Theory R. Thomassyl who had visited the Five Islands of Louisiana between 1857 and 1859, in 1860 described them with some care, noting their distinct character, alignment, and similarity, and ascribing to them a volcanic origin. He regarded them as being akin to the mud lumps in the delta of the Mississippi and was impressed by their symmetry and by the ponds or lakes which occur on several of the islands and which he regarded

Jan 1, 1920

By W. D. Mayercheck

Beginning in 1974, the Bureau of Mines, US Department of Interior, sponsored research and development efforts related to further development and use of continuous face haulage in underground coal mines (Cowan, 1975). The Department of Energy continued this effort as of Oct. 1977. This paper represents an update of an article previously published in Mining Engineering magazine (Mayercheck, 1979). Development progress is summarized for a variety of prototype systems for components now being built, surface tested, or tried underground.

Jan 1, 1984

By R. B. Toombs

The national and international importance of Canada's minerals and metals producing industry is reported. The growth of the Canadian industry is traced from 1945, through the period of rapid development of the early 1950's, to the consolidation and expansion activities of the late 1950's and early 1960's. Mineral production in Canada during 1963-including steel, nonferrous metals, and fuels -is reported. It is estimated that by 1970 the Canadian industry will produce $3.9 billion worth of metals, nonmetals, and fuels.

Jan 8, 1964

By Jasper Whiting

It is well known that there is no better indication of the working of a blast-furnace than is ,given by analyses of its gases; yet although many indiviclual analyses have been made, there is, I think, no

Jan 1, 1892

By F. W. Clark

At the present time, when lixiviation versus amalgamation is being so thoroughly discussed by practical men, and published information is so meagre, the following tests, made by students in the mining laboratory of the Massachusetts Institute of Technology, may be of interest to others. The ore experimented upon was obtained from the Sombrerete mines near Zacatecas, Mexico. A careful analysis of the dried sample resulted as follows : Per cent. SiO2,............62.79 S.............13.86 Al2O3............4.39 Fe,............11.26 Zn,............1.57 CaO.............2.91 MgO,........... 0.06 Cu,.............0.12 Pb,.............0.40 Sb and As,..........trace CO2,............2.35 Ag,.............0.16 99.87

Jan 1, 1886

By W. O. Hotchkiss

Rock exposures are usually a very small part of the surface area in any mining district and the prospector and geologist must base their deductions as to the area, extent, and structure of various formations upon exposures that seldom form 5 per cent. of the area studied. Most often, outcrops form less than 1 per cent. of an area, so that exploration for mineralized contacts or mineral-bearing formations necessitates drilling, test pitting or tunneling, shaft sinking, and other underground work. In these days of high costs any method that will give definite facts regarding rock? obscured by soil or other material should be used to the greatest possible extent. In the early days of the Lake Superior iron districts, mines were located in the few places where ore was present in outcrops. Later, larger orebodies have been found, in depressions, obscured by soil and other foreign material. Mineralized rocks are oftentimes more weathered, softer, and more easily eroded than unmineralized rocks. It is quite natural, therefore, to expect that such orebodies (particularly where large enough to influence erosion in former physiographic conditions) should lie in depressions and be obscured by later debris. It is not difficult to believe that the history of the development of Lake Superior iron mining may be duplicated in other mining districts, that even larger orebodies than those first mined may be found in areas where the rock exposures, which led to original discoveries, are few or lacking. The chief properties of rocks that can manifest themselves through an obscuring cover are magnetism, electrical effects, radio-activity, gravity, and sound transmission. All of these have been used, to a small extent, to tell us a few things about what lies below the surface that we could not otherwise determine, but none has been used so long and so widely as

Jan 1, 1923

By W. O. Hotchkiss

Rock exposures are usually a very small part of the surface area in any mining district and the prospector and geologist must base their deductions as to the area, extent, and structure of various formations upon exposures that seldom form 5 per cent. of the area studied. Most often, outcrops form less than 1 per cent. of an area, so that exploration for mineralized contacts or mineral-bearing formations necessitates drilling, test pitting or tunneling, shaft sinking, and other underground work. In these days of high costs any method that will give definite facts regarding rock? obscured by soil or other material should be used to the greatest possible extent. In the early days of the Lake Superior iron districts, mines were located in the few places where ore was present in outcrops. Later, larger orebodies have been found, in depressions, obscured by soil and other foreign material. Mineralized rocks are oftentimes more weathered, softer, and more easily eroded than unmineralized rocks. It is quite natural, therefore, to expect that such orebodies (particularly where large enough to influence erosion in former physiographic conditions) should lie in depressions and be obscured by later debris. It is not difficult to believe that the history of the development of Lake Superior iron mining may be duplicated in other mining districts, that even larger orebodies than those first mined may be found in areas where the rock exposures, which led to original discoveries, are few or lacking. The chief properties of rocks that can manifest themselves through an obscuring cover are magnetism, electrical effects, radio-activity, gravity, and sound transmission. All of these have been used, to a small extent, to tell us a few things about what lies below the surface that we could not otherwise determine, but none has been used so long and so widely as

Jan 1, 1923

By Charles Mitke

(San Francisco Meeting, September, 1915) INTRODUCTION THE Copper Queen mine is composed of seven divisions which are operated through the following shafts: Division Shaft Depth, Air Current No. Feet Uncle Sam 600 Downcast (shut clown April, 1914, to 1 curtail production) Southwest 600 Downcast 2 Czar 400 Downcast 3 Holbrook 600 Downcast 4 Spray S00 Downcast (shut clown April, 1914, to curtail production) 5 Gardner 1,000 Downcast 6 1 Dallas 1,400 Downcast 1 Lowell 1,600 Upcast 7 Sacramento 1,700 Downcast " I I The workings of the different shafts are connected by motor-haulage drifts on the even numbered levels. The general location of the orebodies and workings is illustrated by the vertical projection of orebodies of the district as shown in Fig. 1. The Uncle Sam, Southwest, and Czar workings have many connections to the surface through raises and extensive cracks that were caused by moving ground. These divisions are cool and are ventilated entirely by natural means. The Holbrook is ventilated partly by natural and partly by artificial ventilation, while the Spray, Gardner, Lowell; and Sacramento are ventilated entirely by mechanical means. In some of the divisions mentioned above a considerable quantity of air exhausts through shafts of adjoining properties.

Jan 9, 1915

By Harry Seltz

SEVERAL investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeser1 has made measurements of "average heat capacities" of iron carbide between 1026° and 85° K., using a water calorimeter. His computed true specific heat at 78.1° K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0° K. The cementite used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes" has measured the specific heat of iron carbide, from 102° to 323° K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100° K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3C, S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley' has reviewed these measurements and calculations, and selects those of Roth4 and Naeser5 as worthy of most consideration. Roth has given ?H = 5400 cal. ± 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (ß) he finds OH = 5600 cal. Kelley accepts the rounded figure ?H = 5500 as the heat of formation at 298.1° K., but this value is quite uncertain.

Jan 1, 1939

By Henry Seltz, Cyril Wells, Hugh J. MacDonald

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940