Search Documents

By E. C. Franz

IN an effort to understand high cycle fatigue, as well as to study the mechanism of fracture in general, a number of researches have been undertaken whereby the fracture properties of a metal have been determined under conditions of repeated cyclic prestsain employing high strains with relatively few cycles. Liu, Lynch, Ripling, and Sachs' showed the effect of a definite strain history consisting of small increments of tensile or compressive prestrain upon the flow and fracture characteristics of metals after a limited number of repeated loadings. Liu and SachsW emonstrated by cyclic straining of the aluminum alloy 24s-T4 that the least reduction in ductility was obtained when the compressive stress was nearly equal to the tensile stress. Attempts have been made to correlate the reduction in ductility under such prestraining with conventional fatigue data, as was done by Liu and co-workers.' The following research was conducted to determine if such reduction as has been noted could be correlated with conventional fatigue data or whether the effect resulted from causes extraneous to the basic mechanism of fatigue failure such as strain aging. It might be pointed out in this connection that the reduction in ductility has occurred in alloys that might be susceptible to strain aging or similar behavior, such as alloy 24s-T4. In the present investigation, the test specimens were prepared from the aluminum alloy 75s-T6 and annealed electrolytic copper. Alloy 75s-T6 is a complex precipitation hardenable alloy, whereas electrolytic copper would not be expected to exhibit strain aging effects, particularly at room temperature. The experimental procedure consisted of prestraining test specimens repeatedly by increasing tension in small increments to various total prestrain values, followed by testing to failure in a tension test. The prestraining as well as the final testing was performed on a tensile machine using special fixtures9 0 maintain concentricity of the specimens. After prestraining, the specimens were unloaded as rapidly as possible and immediately reloaded so that the total time lapse between strains was held to a few seconds. Logarithmic or true natural strain was used in all calculations. The results are presented in Figs. 1 and 2. In Fig. 1, the retained ductility, area after prestrain area at fracture is plotted against the tensile prestrain, initial area area after prestrain as abscissa with the number of stress reversals executed to attain the required prestrain plotted as parameter. Several specimens that fractured during

Jan 1, 1955

By R. Thiessen

The question whether the kind, rank and grade of coal is in any way determined by the kind or type of plant from which it originated has been a problem since coal was first studied. Some investigators claim that the kind of plants has contributed none of the attributes that characterize the differences found in the various coals; others claim that all differences are caused by the contributing plant; and others hold that only a few characteristics are inherited from the kind of plant from which the coal originated. Most coalologists, however, give this matter no thought. It can easily be shown that the kind of plant which contributed to a coal had a marked influence on its kind and type. A number of factors enter into this problem, and all unrelated ones must be carefully eliminated, including metamorphism caused by the pressure of the cover, earth movements, mountain building and higher temperature. Only the fundamental substance—the plants out of which coal was formed—• and the causative conditions that gave rise to a peat swamp and the conditions imposed upon the plant and the plant substances during the formation of the peat swamp can be considered. Everything else being equal, the question then is, how far do different classes and types of coal owe their differences to different kinds or types of plants? Geologic Age of Coal Coal has been laid down in almost every geological period since the Devonian era. Even as early as the middle Devonian some coal was formed; although of no value it has great scientific significance. The most valuable coal was deposited during the Carboniferous. The coals of England were formed during the Mississippian, and most of the valuable coals of America, Europe and China during the Mississippian and chiefly the Pennsylvanian. From the Permian come the coals of France, Saxony, Thuringia and Schwarzwald in Germany and of Bohemia and of the Ural districts of Russia. From the Mesozoic come the coals

Jan 1, 1930

By F. W. Maclennan

PAPERS by D. B. Scott, E. G. Deane, and J. H. Hensley, Jr.1 describe the succession of mining methods used in the Miami mine—squarelset system, shrinkage stoping, top-slicing method, and the undercut caving system which was then being used, and which embraced the use of finger raises. The last-named system worked well but when the rich ore was exhausted it became necessary to reduce costs so as to make available a low-grade ore containing an average of less than 0.9 per cent. total copper with less than 0.8 per cent. in sulfide form and with no precious-metal values. There was then developed for this low-grade ore the system of separate large block-caving stopes, in lateral dimensions 150 by 300 ft., or 150 by 150 ft., with intervals between stopes of the same size so that subsequently these pillars may be similarly mined. The results have been most favorable. Under the previous system the production of ore per man-shift for all underground labor was 8 tons. The present production per man-shift underground is 28 tons. In starting this work the problems were: 1. How the ground would cave above the stopes. 2. Whether in the first stopes caving would encroach on the pillars as laid out. 3. Whether in subsequent mining of the pillars waste filling would be drawn from the previously caved adjacent stopes. Fig. 1 is a small key plan for showing the location of cross-sections as well as of ore mined and the limit of the escarpment and limit of cracking on the surface caused by the caving of the capping overlying the ore

Jan 1, 1929

By Charles McElroy White

IT is indeed an honor to have been asked to participate in the program which celebrates the seventy-fifth birthday of the American Institute of Mining and Metallurgical Engineers. This great organization has occupied an important place in the professional and industrial life of this country-of the world. Its members have explored the far reaches of our globe and have played a great part in the discovery, extraction and utilization of the mineral resources upon which our civilization so largely depends. These engineers, together with the restless prospectors, on the one hand, and the scientists, on the other, have literally been the advance scouts of our modern way of life. As such, we owe them a deep and lasting debt of gratitude. May I, therefore, wish many happy returns to the American Institute of Mining and Metallurgical Engineers and express the hope that it may long continue to be of great service, as it has been in the past. The subject assigned to me-Iron Ore and the Steel Industry-is, indeed, important, as one considers the future of our world. I shall give as few figures as possible. Pertinent statistical data are included in the tables in this chapter, which, I think, will prove interesting. Many studies of iron-ore reserves have been -published and are available; hence I shall limit myself mainly to an interpretation of these figures. The statistics data are from standard sources, including the Lake Superior Iron Ore Association, the American Iron and Steel Institute, the United States Bureau of Mines, the United States Geological Survey, the United

Jan 1, 1947

By P. Chiotti, G. R. Kilp

Thermal, metallographic, vapor pressure, and X-ray data were obtained to establish the phase diagram for the zinc-zzrconiz~m system. Five compounds corresponding to the stoi-chiometric formulas ZrZn, ZrZn,, ZrZn,, ZrZn,, and ZrZn14 were observed. All these compounds, with the exception of ZrZn2, which melts congruently at 1180°C under constrained zinc-vapor conditions, undergo pexitectic reactians. The temperature at which the zinc vapor pressure is I atm for a series of alloys was determined from vapor-pressure measurements. The data obtained are summarized in the construction of a I-atm-pressure phase diagram and a phase diagram corresponding to a pressure of less than 10 atm. THE purpose of this investigation was to establish the phase diagram for the zinc-zirconium system. Thermal, metallographic, vapor pressure, and X-ray data were employed in determining the phase regions. Partial investigations of this system have been conducted by Gebhardt1 and Carlson and Borders.' Carlson and Borders studied the high-zirconium region and established the existence of a eutectic at 69 wt pct Zr with a melting point of 1015°C. The terminal phases of the eutectic horizontal were shown to be an intermetallic compound ZrZn and a solid solution of ß zirconium containing 21 wt pct Zn. The ß solid solution decomposes into ZrZn and a zirconium at 750°C. The eutectoid composition is given as 15 wt pct Zn, and the solubility of zinc in a zirconium at temperatures below 750°C is indicated to be negligible. Gebhardt studied the zinc-rich region and observed a lowering of the melting point of zinc from 419.5" to 416°C and temperature horizontals at 545" and970°C. Some preliminary observations by Chiotti, Ratliff, and Kilp were reported by Hayes.2 pietrokowsky3 has reported the compound ZrZn2 to have a cubic MgCu2 structure with ao = 7.396A. MATERIALS AND EXPERIMENTAL PROCEDURES The metals employed in the preparation of alloys were Bunker Hill slab zinc or Baker analyzed reagent granulated zinc, both 99.99 pct pure and hafnium-free iodide-process crystal bar zirconium obtained from the Westinghouse Electric Corp. The zirconium contained 200 ppm Fe, 200 ppm Si, 100 ppm C, and minor amounts of other impurities. The zirconium was milled or machined into thin chips or shavings. These were cleaned with a nitric-hydrofluoric acid solution, rinsed with water, and acetone, and dried just prior to their use in alloy preparation. The granulated zinc was similarly cleaned using dilute nitric or hydrochloric acid. Weighed quantities of these materials, 20 to 30 g total, were mixed and pressed at 20,000 to 70,000 psi to give relatively dense compacts. During the early part of this investigation the pressed compacts were placed in MgO-15 wt pct MgF, crucibles which were then sealed inside of quartz ampules. The compacts were given various prolonged heat treatments prior to their use for thermal analyses, or vapor-pressure measurements. Because of expansion of the compacts and the relatively high zinc vapor pressure it was difficult to heat to the melting temperatures of the alloys without failure of the quartz ampules. Homogenization at temperatures below the melting temperature gave brittle, porous alloys unsuitable for metallographic examination. It was also difficult to prevent condensation and segregation of zinc on the colder parts of the quartz ampules during heating and cooling operations. These problems were eliminated to a great extent by the use of tantalum crucibles. Tantalum proved to be a satisfactory container with little or no reaction between the alloys and the tantalum. Small tantalum thermocouple wells were successfully welded in the bottom of these crucibles. Pressed compacts were sealed inside the tantalum crucibles by welding on preformed caps under an argon atmosphere. Heat treating and differential thermal analysis were combined into a single operation. The experimental sample assembly is shown in Fig. 1. This assembly was enclosed inside a stainless-steel tube heating chamber which could be evacuated and filled with an inert gas. The thermocouple leads were brought out of the heating chamber between two rubber gaskets used to provide a vacuum seal for the water-cooled head. Most of the compounds in this system undergo peritectic decomposition. After heating above the temperature of a particular peritectic horizontal the sample was cooled to just below the peritectic temperature and held at temperature for several hours. The sample was then reheated through the peritectic temperature and the size of the thermal arrest, if still present, compared with the one previously obtained. If the thermal arrest was not characteristic for the alloy composition being investigated its magnitude diminished and repeated cycling and annealing eventually eliminated it. The peritectic thermal arrests characteristic of a particular composition were established in this manner.

Jan 1, 1960

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined for the system gadolinium-nickel. Nine intermetallic compounds have been found at compositions corresponding to the following gadolinium-nickel ratios: 3:1, 3:2, 1:1, 1:2, 1:3, 2:7, 1:4, 1:5, 2:17. The GdNi and GdNi5 compounds have congruent melting points of 1300' and 1500°C, respectively while the remaining compounds melt in-congruently. Eutectics exist at 15 wt pct Ni, 31 1/2 wt pct Ni and 87 wt pct Ni with melting points of 6703 8803 and 1220°C, respectively. IN a continuing investigation of the properties of rare earth alloys, a study has been made of the gadolinium-nickel system. Previous work encompassed the iron containing alloys and a subsequent paper will deal with the constitution of the gadolinium-cobalt system. Vogel,1 examined alloys of nickel with lanthanum and cerium. R3Ni, RNi, RNi2, RNi3, RNi4, and RNi5 compounds were found. Endter and Klemm,2 Fulling et al.3 Heumann,4 and Nowotny5 found the 1:2 compositions of this series to exist in a C-15 (face-centered cubic) structure, and the 1:5 compositions in a hexagonal system. Jepson and Duwez6 more recently examined these 1:2 and 1:5 compositions and generally confirmed earlier data while Wernick and Geller7 most recently have given additional data on the GdNi5 compound. Comparisons with our results will be made in the appropriate section of this report. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been given in our earlier paper.8 Chemical analyses of the alloy samples were made by dissolving the specimen in nitric acid, precipitating the gadolinium as hydroxide and the nickel with dimethylglyoxime. Both precipitates were ignited to oxide and weighed. RESULTS Microstructure— Metallography of alloy specimens in this series has been conducted on both arc-melted and annealed materials. Etchants used have been 5 pct nital with approximately 10 pct distilled water added, for high gadolinium samples; Carapella's ferric chloride solution for intermediate compositions; and Marble's (copper sulfate) reagent for high nickel content alloys. Because of difficulties encountered in the grinding and polishing of specimens containing 40 to 75 wt pct Ni, no photomicrographs were made of such specimens. The microstructure of an arc-melted 5.3 wt pct Ni alloy is shown in Fig. 1. Light etching primary grains of gadolinium are embedded in an eutectic matrix. The microstructure of an alloy of 9.55 wt pct Ni alloy, Fig. 2, annealed 50 hr at 700°C, consists almost entirely of the intermetallic compound Gd3Ni. The structure of an arc metal alloy of approximately 19 pct Ni, Fig. 3, consists of grains of the compound GdNi embedded in the Gd3Ni2-Gd3Ni eutectic. The arc-cast structure of the 38.7 wt pct Ni alloy is shown in Fig. 4. Large primary grains of a compound rest in a matrix structure of coarse GdNi-GdNiz eutectic. Because of the occurrence of several peritectic compounds in the central region of the diagram, identification of the primary structure in this alloy is not certain. As has been indicated above, microstructures of alloy specimens containing between ca 40 and 75 wt pct Ni have not been photographed. These specimens were highly brittle, and macro- and micro-cracking were impossible to control in the grinding and polishing procedures. Prolonged annealing did not alleviate this condition. Visual observations in small specimens did, however, provide evidence for a multiplicity of phases and peritectic dissociations of compounds although rationalization of structures was not possible.

Jan 1, 1962

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low, a medium, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0% ash, as follows: from low-volatile anthracite, 0.7%; from medium-volatile coal, 1.0%; and from high-volatile coal, 2.3%. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0% or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a convc.ntiona1 dense-media washing plant. Anthracite preparation practices during much of the industry's history were geared to maximum recovery of the larger sizes, pea through egg, which were used in hand-fired, domestic furnaces. Those sizes were cleaned to meet trade requirements, and the smaller sizes were usually higher in ash content. The impression, thus, was that ash content of anthracite always increased as the sizes got smaller. It was presumed that it was impossible to wash the finer sizes to extremely low ash contents. Following World War 11, the classical domestic market began to decline and the finer sizes assumed an increasingly large share of the market. For example, in 1949l 61% of the production was still pea and larger. Fig. l2 shows that -by 1955 these sizes accounted for only 50%, and in 1965, they were only 39% of the total anthracite produced. With the reduction in the market, increased quality was demanded, especially in export markets, and an increasing number of dense-media magnetite washers were installed in new and existing cleaning plants. In 1965, the coarse coal prepared at 59 breakers in the anthracite fields was sampled by the U.S. Bureau of Mines (USBM); approximately 50% of these plants were equipped with dense-media magnetite washers.3 Since 1950, more attention has been focused on the use of finer sizes for numerous industrial uses, including iron-ore sintering, pelletizing, foundry coke-making, cement manufacture, production of calcium carbide, and of carbon electrodes, etc. Most industrial uses require relatively clean anthracite, such as 10 to 11% ash for sintering and foundry coke, 7% for aluminum melting-pot cathode carbon, and 5% for carbide production. Hence, cleaning methods have been improved to the extent that dense-media washers, hydraulic cyclones, and flotation cells have been introduced as fine-coal-cleaning devices. It is now possible to wash the buckwheat, rice, and barley sizes (9116 X 3132-in.) to ash contents as low as 8 to 10% in dense-media devices, but washing the -3132-in. sizes to those limits presents more difficult problems, due mainly to the fineness of the material. This USBM investigation was conducted to determine the amount and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. The goal was to reduce the ash content to a level acceptable for industrial carbon uses, including electrode manufacture, which generally requires an ash content of 1% or less. While low-ash content is of primary importance in selecting industrial carbons, the amounts of other constituents are also important, including iron, silicon, titanium, nickel, vanadium, and sulfur. They were not considered in this work, since their occurrence in deashed anthracite has been studied elsewhere.4 The results of the present investigation were used to design a flowsheet, suggesting a method for producing ultraclean anthracite as part of conventional preparation practice, using dense-media vessels, crushers, pulverizers,

Jan 1, 1970

By P. Somasundaran

Adsorption of a nonionic polyacrylamide (PAM), an anionic polyacrylamide with sulfonate functional groups (PAMS), and a cationic polyacrylamide with amine functional groups (PAMD), on hematite was investigated as a function of different solution conditions. Adsorption results indicate that the major mechanisms of adsorption of polyacrylamides on hematite is through hydrogen bonding, with electrostatic forces playing a secondary role. All the polymers exhibited irreversibility of adsorption upon dilution. Also, entropic effects were determined to be important in adsorption. Surface chemical properties of hematite and solution chemistry of the polyacrylamides are considered to explain the polymer adsorption behavior on hematite.

Jan 1, 1985

By Stanley J. Gasior, Albert J. Forney, Joseph H. Field

Most bituminous coal mined near Eastern industrial areas requiring high-Btu pipeline gas is caking and therefore unsuitable for fixed-bed pres- sure gasification by present techniques. If the caking property of such coal can be destroyed, the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work, strongly caking coals of 1/8- to 1½ -in. size were converted to a noncaking coal char by treatment in a static bed in about 3 hours1 and coal of 18-100 Tyler mesh in a fluidized bed in about 5 min.2 An inert gas such as steam, nitrogen, carbon dioxide or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a noncaking form in free-fall in about 2 sec by dropping it through a countercurrent flow of steam containing 4% to 7% oxygen at 1150º-1200°F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 3, 1965

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers.

Jan 1, 1923

WITH the economic situation of the world what it is, we may expect important events in every month of 1922, and January showed us some-what of the nature of things that will happen. The Germans announced their inability to meet in full the reparation payments that were due Jan. 15. The Su-preme Council arranged a plan for them to pay some thing on account every 10 days, and called a conference at Cannes to talk things over. While this conference was in progress Premier Briand resigned and was suc-ceeded by Poincaré. This emphasized the growing differences between British and French policies and interests. The French want to exact the utmost from the Germans; so do the British. The latter think, however, that the French aims will so cripple the Germans that they can not work properly and hence can not trade. Great Britain, with a huge unemploy-ment problem, must have trade. The French thought that Briand was unduly deferring to the British and withdrew their support of him. The other important political developments of the month in Europe were the establishment of the Irish Free State, relieving the British of the vexatious Irish question; and the growing tendency to recognize the Soviet government of Russia and admit its representa-tives into international conferences. In the United States the great political event was the establishment of the dominance of the agricultural bloc in the Senate, which implies the passage of agrarian legislation that will probably be unwise. Economically, there was no progress in the United States. If anything there was probably some reces-sion in the physical volume of business. There were some further reductions of wages, but these were irregular, geographically, and moderate in amount. The great unionized trades maintained the jam. Events of great importance were the formal demand of the anthracite coal miners for increased wages on April 1 and the declaration of the bituminous coal miners that they would resist a reduction at that time. The attitude of these groups is believed to presage labor troubles in the spring. In the metal markets affairs were dull during Janu-ary, but prices were generally firm, save for a little further weakening in iron and steel. In the matter of production, however, there was some quickening of activity, especially in copper, zinc and iron.

Jan 2, 1922

By F. C. Sturges

FOR some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are solved. Recently we have completed two 36-in. diam. core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years [ ] and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam. shafts were considered, but actual computations showed 36-in. diam. shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1947

By F. C. Sturges

For some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are, solved. Recently we have completed two 36-in. diam core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam shafts were considered, but actual computations showed 36-in. diam shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could .be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1949

By Simon D. Strauss

Production and consumption of nonferrous metals in the United States during 1950 were at peak levels for the postwar period, as is shown in Tables I, II, and III. The trend of production was upward through most of the year. At the year end, with the possible exception of the Tri-State zinc-lead district, the large mining operations in the country were running at capacity. The absence of serious labor interruptions during the year was an important contributing factor in the increased out-put of metals, since in each of the previous postwar years there had been a number of major strikes which affected production adversely.

Jan 2, 1951

By Hugh Henton

THIS paper is the result of an investigation made in association with Dr. Charles H. Fulton. Early in 1918 a search was started for methods of utilizing, in the manufacture of basic refractories, certain domestic resources in magnesites, dolomites, and magnesian limestones. Much information was collected during that year and during 1919 regarding magnesite and dolomite deposits. During 1920 and 1921 a research was made into methods of calcining dolomite and separating magnesia therefrom. Some success was attained and many new ideas were brought out in connection with the preparation and utilization of magnesia in the form of "caustic" or light-burned material as well as in the form of refractory or "dead-burned" material. Stimulated by this success, much advance has been made in manufacturing processes for the "plastic magnesia," so called, used for magnesia cement, stucco, flooring and otherwise in the structural industries.

Jan 3, 1926

By William M. Kester

INTRODUCTION The Coal Research Bureau of the School of Mines at West Virginia University is presently conducting laboratory-scale tests to determine the technical feasibility of beneficiating pulverized coal and coal fines with high-intensity electromagnetic fields. Interest in magnetic processes for cleaning fine coals was stimulated by results obtained by Yurovsky, et a1 in 1958.1 This work, while not new in concept,2,3 indicated that pulverized coal which had been thermally treated in a rotary drum in the presence of superheated steam and air underwent thermo- chemical reactions. Films of the ferromagnetic minerals magnetite (Fe2O3), hematite (Fe3O4), and pyrrhotite (FeS[3]) were reported to be formed on the surfaces of the pyrite grains associated with fine coal during the foregoing treatment at temperatures ranging from 120 to 360°C. After thermal treatment the coal was magnetically separated in an experimental magnetic device having a field strength of 10,000 oersteds.

Jan 5, 1965

The economic recovery of metals from dilute solutions has been the dream of mining engineers for many years. This subject is now receiving greater attention, particularly for copper, in view of the heightened demand for the metal and the tightening supply situation. A Copper Precipitation session, sponsored jointly by EMD Hydrometallurgy Committee and MBD, which took place during the Annual Meeting in March, heard papers on recent research and plant practice. Although the bulk of research in hydrometallurgy has been carried out in countries other than the United States1, producers in this country are making important contributions to the heap or dump leaching system. They realize that the processes are essentially simple to install and give high recovery rates at reasonable cost. Jacobi estimated in 1963 2 that the copper mining industry obtained a gross return from scavenging operations -on a worldwide basis-on the order of $20 million annually, subject to the usual deductions for refining and realization charges, overheads, taxes, etc.

Jan 6, 1966

The history of surface mining is essentially that of mining coal, copper, and iron ores and the non- metallic minerals, i.e. clays, gypsum, phosphate rock, sand, gravel and stone. The accompanying table comparing world production with that of the U. S. indicates that two thirds of the 8.8 billion tons of ores mined throughout the world come from surface operation. Assuming that the stripping ratio for surface mining in the U. S. applies equally to world production, then over 21 billion tons of waste, or a total of nearly 27 billion short tons of material are mined annually in the world by surface methods. Several factors are significant indicators of economic and technologic trends in surface mining. Among these are increasing production, a shift in emphasis from underground to surface mining, a decline in the grade and quality of some crude materials and, with few exceptions, an increase in the productivity of labor.

Jan 10, 1967

By Bernard E. Weichman

The oil shales of the Green River formation were deposited in an inland lake which contained abundant plant and animal life. A high percentage of sodium bicarbonate existed in the lower water layers. Digestion of the kerogen-rich mud accumulating on the lake floor lowered the pH of the interstitial waters and precipitated the sodium minerals dawsonite and nahcolite in the kerogen-rich mud. After about five million years of existence, uplift of land areas around the lake caused an influx of clastic sediments which filled up the lake. Continued tectionics gently folded the basin and caused fracturing of the kerogen-lean oil shale. Nahcolite existing in the fractured lean oil shale was dissolved by subsurface waters leaving a tremendous aquifer in a portion of the oil shale. The extent and porosity of the "Leached zone" aquifer is dependent upon the percent of kerogen and nahcolite originally deposited in the oil shale.

Jan 1, 1975

A school grows big only as its usefulness increases and it will shrink rapidly if inefficient. Usefulness must be recorded in terms of service within the economic structure of the Commonwealth. Under this premise, modern mineral industries colleges must recognize and give equal significance to three interrelated, interdependent functions of service: namely, (1) resident instruction, on both the undergraduate and graduate levels; (2) research under an experiment station plan; and (3) extension training under three classifications, class instruction, correspondence instruction, and informal instruction. To train potential leaders for the mineral kingdom, to discover and teach new truths is only half of the job. Through extension training, equal attention must be given to the on-job, vocational-technical, upgrading of skilled workers on the production line. Similar to the School of Agriculture, the School of Mineral Industries is the only one in the Commonwealth offering the three functions of service in each of the subject-matter fields in mineral arts and sciences. The functions of service must be based on the modern conception of mineral conservation (Fig. 12). Conservation of minerals differs from conservation of natural resources in general because man must find new mineral deposits and excel the geologic forces of nature in processes of concentration. True mineral conservation, therefore, may be defined as energetic discovery,

Jan 1, 1950