Search Documents

By C. E. Lawall, C. T. Holland

When this study was started very little information was available regarding the physical characteristics of West Virginia coals. This was particularly true of friability and of crushing strengths of the coals. Some work had been done on specific gravity studies but the available information applied to only a few coals. In practically all coal-classification systems thus far proposed, the predominating factors of classifications are largely based on the chemical characteristics of the coal. Recently some investigators have pointed out that a classification based on chemical and physical properties of coal might serve to place coals in their proper group better than classification systems based on chemical properties alone. One of the aims of this study was to obtain some data on the physical properties of coal which might help to classify West Virginia coals. The Samples Fig. I shows where the coal samples were obtained and the approximate division line of the high and low-volatile coal fields of the state. The relative geological horizons of the coal beds tested are shown in Fig. 2. In securing samples of coal for friability and specific gravity tests, it was the aim always to obtain a representative sample of lump coal produced at a particular mine. The samples were obtained from the loading boom, the railroad car, or the mine cars. Wherever it was possible to secure samples from a loading boom they were taken from it by taking shovelfuls of coal from the loading boom every minute until about 200 lb. of coal was obtained. If there were no loading booms used at the mines sampled, the coal sample was taken from a loaded railroad car by systematically taking shovelfuls of coal at definite intervals over the whole top of the car until about 200 Ib. of coal was obtained.

Jan 1, 1932

By E. M. Wise

The practice of adding moderate quantities of nickel to a variety of bronzes has been employed by foundrymen for many years with several objects in view. In some instances it was desired to harden the alloy; in others it was to increase the fluidity or to improve the solidity of the castings, or to refine their grain. These important matters have been considered in detail by Pilling and Kihlgrenl and by numerous other workers cited by them, and with the exception of the first will not be considered in the present communication. The possibility of reducing the cost of bronze by replacing a portion of the tin with nickel received attention some years ago by Burgess and Woodward12 and, as will be shown later, offers attractive savings in cost under present conditions. The age-hardening characteristics of the nickel bronzes of appropriate compositions have been known for some time and were mentioned by Price, Grant and Phillips3 and discussed by Wise4 in connection with their paper. These matters are further considered in recent patents15 and are becoming of commercial importance in the production of high-strength castings. The equilibrium relations existing in the high-copper region of the copper-nickel-tin system have been carefully studied by Eash and Upthegrove,6 and in somewhat less detail by Veszelka.7 The observa-

Jan 1, 1934

By AIME AIME

T'HE Columbia Section of the A. 1. M. E. took charge of the Western Mining Convention on Oct. 3, and the meeting was held under their auspices. W. L. Zeigler, chairman of the Section, called the session to order. The first paper on the program, "Lead Refining Practice at Bunker Hill Smelter," was presented in per-son by the author, A. F. Beasley, superintendent of the smelter. He pointed out the differences in the refining practice at Bunker Hill from other American refineries. The Bunker Hill plant was the first to adopt the liquation process for silver skims as developed in Australia. Details were given of operating practice with results. F. F. Colcord questioned the author in regard to the kind of metal best suited for kettles, which was said to be cast iron.

Jan 1, 1929

The committee appointed .by W. R. Ingalls, president of the Mining and Metallurgical Society of America, to nominate candidates for the' annual gold medal of the Society consisted of E. G. Spilsbury, J. E. Johnson, Jr., and Bradley Stoughton. This committee recommended Mr. Schneider of the Creuzot Works in France for achievements in ferrous metallurgy, which recommendation was approved by the Society. From the report of the committee, the following facts relative to Mr. Schneider's career are taken: Born in 1868, Charles Eugene Schneider undertook the management of the Schneider establishment in 1898, after the death of his father, Henri Schneider. Under his enlightened management, the Schneider establishments have been considerably extended, their activity being not only directed to increasing production, but also to spreading more and more their scope for action in all branches of industry-in metallurgy, mechanical and electrical construction, shipbuilding, artillery and ammunition, and in public works. During the 10 years preceding the war, the number of employees in these establishments, and without counting those of the more numerous subsidiaries, increased approximately 50 per cent. While giving to peace industries all the attention necessitated by the progress in science and the continual improvement in industrial methods and products, Eugene Schneider, with a perspicacity that recent events have justified in a striking manner, especially directed his

Jan 3, 1919

Jan 1, 1969

By S. Floreen

Seven iron alloys ranging from 5 to 12 pct Ni and 5 to 14 pct Cr were studied. All alloys transformed to bcc massive martensites. Tempering increased the strengths , probably because of relief of residual stresses generated by the martensite transformation. The major strengthening mechanism appeared to be solid-solution hardening by nickel and chromium. Studies of the work-hardening behaviw, of the effects of prior austenite grain size, and of the effects of changing strain rate and test temperature gaue results very similar to iron or low-alloy steels. Increasing nickel contents markedly improved the toughness at subzero temperatures. Studies of the flow properties did not, however, indicate the reason for the beneficial effect of nickel on toughness. The marine atmosphere corrosion resistance of the alloys was improved primarily by chromium additions, but increasing nickel contents were also beneficial at low levels of chromium. J\ number of maraging and PH stainless steels are strengthened by precipitation hardening in a low-carbon Fe-Ni-Cr martensite matrix. To some extent the resultant properties of these steels must depend upon the properties of this matrix. The present study therefore was conducted to evaluate the transformation characteristics and mechanical properties of a series of Fe-Ni-Cr martensitic ternary alloys. A limited evaluation of the corrosion resistance of the alloys in marine atmosphere was also made. ALLOY PREPARATION Seven 100-lb air induction melts were prepared using electrolytic iron, nickel, and chromium metal additions. The initial Fe-Ni charge also contained 0.05 wt pct graphite to produce a carbon boil during melt down. After melting of the base charge, the heats were refined with 0.1 wt pct additions of manganese, silicon, aluminum and titanium and poured into cast-iron molds. The ingots were homogenized at 1250°C and uni-directionally hot-rolled to 2-in. plate. They were then homogenized another hour at 1250°C, and unidirection-ally hot-rolled to %-in. plate at a finishing temperature of approximately 1050°C. The compositions of the heats are given in Table I. Two additional heats were prepared as 40-lb vacuum-induction melts using electrolytic iron, nickel, and chromium metals, and commercially pure molybdenum chips. A carbon boil, and 0.1 wt pct additions of aluminum and titanium were again employed, but manganese and silicon were not added. The heats were converted to %-in. plate using the procedure described above. The compositions of these heats are included in Table I.

Jan 1, 1967

By James H. Allen

The development of large diameter rotary drilling techniques and equipment in the last nine years has been the main factor for the rapid advancement made by this method of shaft construction. In 1959, less than 5000 ft of large diameter hole was drilled in the United States for the mining and construction industries. By 1967, large diameter hole footage had increased to 117,000 ft. Part of the increase in footage for holes drilled represents AEC requirements due to the discontinuance of atmospheric testing of nuclear devices. The increase in footage for holes drilled for the mining industry can be attributed to cost savings of shaft construction by rotary methods as compared to conventional blasting methods. Until the late 1950's most large diameter holes were drilled with positive displacement rig pumps or air compressors, direct mud or air circulation, conventional sized oil well drilling strings, and multipass reaming techniques. In some very soft formations it was possible to run a pilot bit with one or more hole openers in tandem to drill the hole in a single pass. The main problem with single pass drilling using tandem hole openers was in providing sufficient circulation fluid for proper hole cleaning through conventional sized drill pipe.

Jan 11, 1968

By M. D. Cooper

Production of both anthracite and bituminous coal in 1954 was about 16 pct below 1953. Estimates on Dec. 1, 1954, indicated 27 million tons of anthracite and 385 million tons of bituminous. Decline in production was due principally to lower demand by the steel industry and the railroads, although competition from other fuels also affected coal. The year was notable for vigorous effort by the coal industry to promote the use of its product. A Cabinet Committee on Energy Supplies and Resources Policy and an Interdepartmental Committee on the Soft Coal Industry were set up by the Administration in Washington. A Governors' Fuel Conference was also organized.

Jan 3, 1955

By James F. Lewis

THE hematite iron ore mines east of the Hudson River are confined to a strip of country ten to fifteen miles wide, commencing on the south, near Fishkill, running northeast through Dutchess County, and striking the southeast corner of Columbia County, extending into Litchfield County, Conn., known there as the Salisbury mines, cropping out again at and near West Stockbridge, Lanesboro, and Cheshire, Mass., also in Bennington County, Vermont. The ores are found in beds or deposits and in veins, with a limestone ledge on one side and slate on the other, from six to thirty feet from the surface. Portions of it are quite solid, called rock ore, but

Jan 1, 1877

ENROLLMENT of both undergraduate and graduate mineral engineering students rose approximately 11.8 pct over last year to a total of 12,830. Leading again in the enrollment climb was ceramic engineering which increased by about 21 pct. Approximated increases in enrollment of the other mineral engineering categories, in order, were: metallurgical 17.7 pct; petroleum 13.3 pct; geological and geophysical 3.3 pct: and mining proper, the lowest with 2.9 pct. Total ECPD school enrollment climbed to 242,405 -just below the 1947 peak, but 14.4 pct higher than 1955. Engineering enrollments have shown a general increase since 1951, and freshmen enrollments have climbed steadily since 1950.

Jan 5, 1957

By R. S. Wagner, W. G. Pfann

METHODS that have been used to measure stress relaxation in metals and plastics have been reviewed recently by G. R. Gohn and A. FOX.' The ideal stress relaxation test comprises placing a sample under a constant strain (usually considered

Jan 1, 1962

Jan 1, 1965

By Yasushi Ishikawa

The fact that the degree of granulation and the state of granulated particles of sinter raw mixtures are the influential factors in ensuring coke combustibility and permeability during sintering has been clarified. Based on this knowledge, Nippon Steel developed the divided coke-addition process and the technology to utilize binder, and applied them on a commercial scale. Productivity and sinter quality are thereby greatly improved with a significant reduction in fuel consumption.

Jan 1, 1977

By William P. Mason

FoR reasons unnecessary to enter into here, I was called upon to contradict the statement that " closed metallic vessels, partly filled with water and heated, do not become shattered by violent explosion, but simply rupture by over-pressure;" and the following experimental results were obtained in support of my position : A piece of drawn brass tubing (telescope-tubing) 1 1/2 inches in diameter and 15 inches long was closed at both ends by screwing on heavy caps of bronze. Before closing the second end the vessel was half filled with river water, the cap was then screwed on, and the closed vessel was supported upon two iron anvils, and heated in the interval between the supports by a large Bunsen lamp. The resulting explosion (which was doe to over-pressure only and not to any more occult cause) was exceedingly violent. No small damage was done to the room in which the experiment was undertaken; and the noise was like that of a cannon. Those of the pieces which could be recovered are shown in Fig. 1. Upon examining the wreck, it was noticed that one of the heavy bronze end-caps had preserved its circular section and still contained that portion of the barrel of the tube which had been screwed into it, while the other end-cap contained no portion of the tube, and was moreover sprung into a shape more or less elliptical, as if from excessive lateral strain. It was also observed that the large pieces of the shattered boiler predominated towards the end which had been closed by the un-sprung end-cap. The reasonable explanation, in view of the facts, was, that over-pressure had caused the boiler to yield through the screw-threads at A B, Fig. 2, and the righthand end-cap had blown off, thus leaving the boiler half filled with water, greatly super-heated for the new (atmospheric) pressure to which it was suddenly reduced; that this water had consequently sprung instantly into steam with dynamite effect, shattering the tube and springing the remaining end-cap. The large pieces would be expected at the open end of the boiler, as at that point the "tamping "would have been that of the atmosphere only. This explanation assumes a rupture to have been caused by gradually increased pres-

Jan 1, 1893

By G. E. Kedzie

The ore-deposits of ail that portion of the San Juan country within the borders of Ouray County are either in the tertiary ernptives or, confined to a relatively narrow zone, in the sedimentary beds just beneath them. The ore-deposits in the igneous formation

Jan 1, 1888

By R. B. Tippin

Laboratory and pilot plant studies showed that supergrade iron ore concentrates (containing less than 2% SiO2) can be made from standard grade magnetic iron ore products by cationic silica flotation. Continuous tests were run using various flowsheet arrangements. whereby (1) super and standard grade products were made simultaneously or (2) only a superconcentrate was produced. After a caustic scrub and desliming pretreatment, the silica in a magnetic taconite concentrate was reduced to 1.8% SiO2 by amine flotation. Approximately 75% of the iron was recovered in the single flotation stage, and by additional beneficiation 95% of the total iron was ultimately recovered,

Jan 1, 1973

By J. E. Lawver, W. D. Carrier

During the past 20 years, millions of dollars in research effort have been spent to improve methods of phosphate clay dewatering and disposal. Although to date no proven large-scale system has been developed that will result in ultimate below ground storage without the use of at least temporary dams, considerable progress has been made and a variety of techniques are being tested, some on a large scale. This paper summarizes the use of mathematical and centrifuge (physical) models that can analyze and evaluate various systems for the consolidation of phosphatic clays. These provide a powerful tool for engineers responsible for land management and mining waste disposal.

Jan 1, 1985

By D. E. Swets, P. C. Frank, D. L. Fry

THE hydrogen-steel system has received considerable attention in the past several years. Recent experiments in this laboratory have shown that another group of operations, namely, sanding and grinding,' must be added to the already well-estab- lished list of phenomena that cause hydrogen to permeate steel. Qualitative tests which have been made with a very sensitive ion-gage type of detector similar to that used by Norton,' showed that sanding a steel surface caused hydrogen permeation. A metal type 6~6 vacuum tube was used as the ion gage with an electrometer to measure the ion c~rrent.~ The protective enamel coating was removed from the tube.

Jan 1, 1959

By K. Stout, L. Friel

Some rock mechanics theorists believe that if a hydraulically placed backfill can be introduced in a stoped out area, which will minimize wall closure by taking high stresses across the fill with minimum compaction, then heavy ground and rock burst phenomena will be minimized. The paper will discuss a large scale laboratory project when fill strength was increased over four times by the head vibrated method and up to well over 20 times by the double placed, cemented, vibrated head method when compared to conventionally placed fills. The only preconditioning of the 60% solids by weight slurry was the addition of cement in some tests.

Jan 1, 1983

By H. V. Fairbanks

Efforts were made to determine the amount of increase in the drying rate which could be obtained through acoustic treatment of ultra fine coal under various conditions, and to test the feasibility of using a rotary kiln and multitiered vibrating screens as a means for continuous drying of coal fines. Introduction of acoustic energy during the rotary kiln experiments increased the drying rates from 10-40%, depending upon the experimental condition. The use of a drying assembly consisting of multitiered vibrating screens produced better results than the rotary kiln and has definite possibilities of providing an effective means of drying coal fines in relatively large quantities.

Jan 1, 1973