Search Documents

By Ernest A. Kaarsberg

This paper presents the results of studies of the elasticity of some isotropic and anisotropic rock samples based on longitudinal- and shear-wave pulse velocity measurements. Experimental evidence from velocity measurements on isotropic steel samples is also presented to show, within error limits, that any two of the elastic constants required to completely describe the elasticity of an isotropic solid can be obtained from any two of the following four velocity measurements: longitudinal "rod,' "plate," extended medium (infinite medium equivalent), or shear wave. Measurements of three of these velocities in an approximately isotropic basaltic rock sample are used to illustrate this application to this type of rock. For the anisotropic study, a suite of Colorado oil shale samples is used. These rocks exhibited transverse isotropy. The five elastic constants required to completely specify this type of anisotropy are obtained from longitudinal- and shear-wave pulse velocity measurements made in directions parallel, perpen-dicular, and at 45° to the bedding plane. Density, velocity, and elastic modulus relationships among these shales are also given. Duvall 1 has described a method for determining the elastic constants of isotropic and, in two cases, anisotropic rock samples. This method is based on ultrasonic pulse techniques and on resonance-frequency measurements of rock samples in the shape of rods (diamond drill cores). Rock samples, however, are not always available in rod form. When this is the case, other methods can be used to study their

Jan 1, 1969

By E. A. Breitenbach

A computer program has been developed to afford rapid and complete quantitative log analysis for exploration and production decisions. The computation consists of automatic selection of tops and bottoms of porous intervals from the digitized data, and then point-by-point calculations within each selected interval. Nearly all log types can be analyzed. This paper presents the calculation techniques found to be appticable to machine evaluation and gives examples of their use. INTRODUCTION As the quantitative interpretation of well logs entails repetitive use of charts and equations, it is natural that digital computer programs would be written. A Universal Log Interpretation Computer Program (ULICP) has been developed to afiord rapid and complete analysis for exploration and production decisions. Application of this program enables the log analyst to: (I) apply rapid quantitative log analysis for exploration and production decisions on either a field, a well or on a single zone basis; (2) apply concepts of interpretation requiring detailed numerical analysis; (3) analyze all porous intervals on each log, rather than a few selected zones, and complete the analysis in less time than previously required. Computations are reported for every digitized point in each zone; (4) use empirical techniques applicable to a given area as an integral part of the computation; (5) experiment with the empirical coefficients and exponents in the interpretation equations to find the best possible solution; and (6) automatically plot both the original and computed data to scales analogous to the field prints. The primary utility of a log interpretation program stems from its ability to do an overwhelming amount of work with very little man-power. If a calculation procedure or thought process can be formalized to the extent that step-by-step logic can be written, a computer program can be developed that follows this logic. The major question is one of economics. A feasibility study of the costs for such a program indicates that digital processing is economical primarily as a means of increasing the productivity of the log analyst. In effect, the probability of missing productive intervals in any well, because of a lack of time to do detailed calculations, is greatly reduced. The nucleus of ULICP is programmed to compute large sections of a suite of logs by selecting zones automatically and then performing all pertinent computations on a data point by data point basis within each zone.'.' An entire suite of logs can be processed in this manner with very little manual intervention. Sufficient programming logic is available so that each log analyst can request computations pertinent to his area. These requests are made by simple additions or deletions of information on the input header cards. Hence, the log analyst is always in complete control of the computation process. The evaluation of a suite of logs requires pre-editing, digitization, computation, presentation of results and interpretation. Work by the log analyst is reqilired only in pre-editing and interpretation. Thus, he is allowed more time for comprehensive interpretation, rather than calculation. For continuity, the discussion of ULICP is organized sequentially: pre-editing, digitization, computation and presentation of results. DISCUSSION PRE-EDITING The extent of pre-editing prior to computation is dependent on the format of the original data. For analog prints, it requires inspection, correlation and editing of the logs, plus the entering of required data an special forms. For digitized data such as magnetic tape field recordings, only the special forms are necessary. The process for analog prints will be given here. The inspection and correlation process involves the selection of sections for digitization and the correlation of the traces to a common depth. To decrease the cost of digitization, traces that exhibit large variations in shale formations can be redrawn to a non-zero baseline. The next step is to enter all pertinent data on the input header cards. The header cards presently used for ULICP are presented as Figs. 1 through 6. Cards 1, 2, 3 and 4 (Fig. 1) are defined as the Main Header Cards. They describe the particular well for output identification and give basic information. Cards 5 through 15 (Figs. 2 through 6) are defined as the Block Header Cards. As such, they define the log types and the interpretation parameters for the block of data immediately following. Cards 1 through 10 are required for every computer run. Cards 11 through 14 pertain only to nuclear logs. Card 11 is required if any nuclear log is supplied, and cards 12 through 14 are required only when gamma-ray, density or neutron log data, respectively, are supplied. Card 15 (Fig. 6) must be supplied when cross-plot calculations are required. Either two- or three-component

Jan 1, 1967

By M. C. Manderson

The sharp drop in world phosphate demand that took place in 1975 due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1979

By M. C. Manderson

Abstract-The sharp drop in world phosphate demand that took place in 1975, due to temporarily high prices, now seems to be reversing itself. And prices for both phosphate rock and phosphate fertilizers, which declined dramatically from their 1975 highs, now appear to be bottoming out. This recent price weakness has delayed new mining ventures that had previously been planned for completion by around 1980. While there is ample capacity to supply near-term rock needs, the stage seems to be emerging for a better supply-demand and price environment in the late 1970's and early 1980's.

Jan 1, 1978

By A. B. Hildebrandt

P. B. Baxendell is to be complimented for an exccllent piece of work. To our knowledge there has been no previous publication of field data on the flow of oil and gas through the annulus of a well. It is certainly gratifying to see this work on annular flow confirm the previous published correlation procedure on tubing flow. It extends considerably the range under which reliable gas-lift calculations can be made. Baxendell discussed this work with us about a year ago and was kind enough to send a large scale plot of his correlation. We had been designing gas-lift installations on flow through the annulus, assuming that the original correlation of the f factor based on tubing flow' was valid as long as we stayed within the same mass velocity range on which the correlation was based. Doing this work necessitated the use of an equivalent diameter for the annular flow. The equivalent diameter is defined as area' of stream cross section wetted perimeter and for the case of an annulus is D, — D,. Substituting this in the basic equation correlating energy loss along with the area to flow required to convert the velocity, to volumetric flow rate, D (Baxendell's Eq. 7) becomes dell's expression, D,). Similarly, the D in 1.4737 X 10 (M&/D) becomes (D, + D;) for annular flow. On receipt of Baxendell's data, we. of course, recalculated it to put it into the form we were using, and to see how well it agreed with the correlation based on tubing flow. Fig. 1 shows the results, which were certainly gratifying. For low values of (D, - D,) pv, the data coincide with the data on flow through tubing, whereas at high values the data on flow through the annuli appear to be leveling off to a constant value. For very high rates of flow where the turbulence is very high, one might expect the value f to level out and become constant. A bulletin published in 1914 by the U. of Wisconsin presented results of a large number of laboratory teats in air lifting water through short lengths of 1.25-in. tubing. It was possible to correlate a random sampling of

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer Continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore. On September 19, 1956, Freeport Sulphur Co. acquired from Humble Oil & Refining Co, the sulfur rights underlying the tracts, and the actual design of the installation began the same month. The first structural contract was awarded in December 1957 and offshore erection began in June 1958. The initial phase of construction has been completed and production by the Frasch process commenced in April 1960. The estimated total cost of the project is $30 million, of which $8 million is the extra cost incurred by the necessity of offshore operations. More than $22 million was expended before production was started. GEOLOGY OF DEPOSIT Grand Isle is the third largest sulfur deposit in the U.S. The orebody embraces several hundred acres, but its outer limits are yet to be defined to the northeast, east, and south. Most Gulf Coast sulfur deposits occur in a caprock mantle of calcite (referred to as limestone), anhydrite, and occasionally gypsum, which covers the apex of an intrusive mass of salt. Commercial quantities of sulfur are usually confined to the calcite or limestone member. Most often such limestone is completely enclosed by dense anhydrite below and impervious sediments above, which effectively form a closed reservoir. The depth of the Grand Isle orebody ranges from 1800 ft to 2500 ft below sea level. Within the present boundary, the sulfur-bearing limestone varies in thickness from 220 ft to 425 ft, while the sulfur content varies an average of about 15 pct in the leanest hole to an average of about 30 pct in the richest. Rock containing less than 5 pct sulfur is not classed as ore, and holes assaying less than 20,-000 long tons per acre of sulfur in place are not considered commercial offshore. The sulfur enrich-

Jan 1, 1961

By George H. Ashley

At the beginning of the war, about 13 years ago, a conference was called in Washington to lay plans for pooling the coals of the United States. A careful review of the various systems of classification then extant showed none well adapted to the needs of coal pooling. The system of Tidewater pools then adopted, using numbers to distinguish one pool from another, was based on typical coals of different localities. At that time, the writer undertook the preparation of such a practical classification. Aside from drawing on his experience of over 20 years in the coal fields of the United States, reaching from the Pacific Coast and the Rio Grande to Rhode Island, he first examined and carded all of the large collection of coals in glass jars made by and for M. R. Campbell. Next, he carded all of the descriptions of coals he could find in the U. S. Geological Survey bulletins and elsewhere, as well as practical tests of coals by the Navy and other organizations and then took account of every published coal analysis of the U. S. Geological Survey and U. S. Bureau of Mines. A study of this information, involving thousands of recomputations, led to the presentation of a paper on "A Use Classification of Coal" before this Institute at the Chicago meeting, September, 1919. That classification was unique (1) in a classification based on "standard coal" which included moisture, but used standardized ash, sulfur and nitrogen, (2) in using physical properties to distinguish the major classes or orders, (3) in recognizing British thermal unit values in the minor subdivision, (4) in the large number of classes recognized (thirty-six), (5) in proposing mineral names for all classes, (6) in proposing a letter code for the several classes for practical use, (7) in proposing a code for expressing what has commonly been called "grade" of the coal, the grade code to be combined with the rank code to designate and describe a coal. The writer still thinks that the principles then offered, though not necessarily the exact proposals, are valid and desirable in any practical classification. The actual classification of coal by rank was based on the ratio of fixed carbon to volatile matter for the high-rank coals—the well-known

Jan 1, 1930

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By AIME AIME

WITH a brilliance undimmed by hard times, the annual dinner on Wednesday evening, Feb. 17, was a complete success. More than 600 members, friends and ladies gathered early and filled the anterooms of the grand ballroom of the Commodore Hotel, while the president's reception was in progress, and then at the sound of the gong and with the music of the orchestra, rising above the happy din of conversation thronged to their seats at the tables. Following the "potage Ambassadeur"-probably to eliminate a very real hazard-the usual toy balloons appeared and a gay and lively scene, punctuated by multitudinous explosions, ensued, as the hundreds, of variously colored spheres bounced yon and hither until their gaseous existence was ended on the glowing end of a cigar or cigarette. On the speakers' dais sat C. E. Beecher, Chairman Petroleum Division; J. Vipond Davies, representative of A. I. M. E. on the Alfred Noble Prize Committee; Corbin T. Eddy, Alfred Noble Prize recipient; A.' S. Tuttle, Vice-president American Society of Civil Engineers; W. C. Mendenhall, Director U. S. Geological Survey; George C. Bateman, representing the Canadian Institute of Mining and Metallurgy; Paul D. Merica, Institute of Metals lecturer and Chairman James Douglas Medal Committee; Champion Herbert Mathewson, James Douglas Medalist; Robert E. Tally; retiring President; G. Temple Bridgman, toast-master; Scott Turner, incoming President; F. W. Bradley, William Lawrence Saunders Medalist; Fred Searls, Jr., Chairman William Lawrence Saunders Gold Medal Committee; Arthur Notman, President Mining and Metallurgical Society of. America; Robert J. Grant, Director U. S. Mint; Landon F. Strobel, Chairman New York Section; Howard Scott, recipient of Robert W. Hunt Prize; George. B. Waterhouse, Chairman Robert W. Hunt Prize Committee; F. M. Becket, Chairman Iron and Steel Division; Ora E. Clark, recipient of the J. E. Johnson, Jr., Award; Richard Peters, Jr., Chairman J. E. Johnson, Jr., Award Committee; E. C. Bain, Howe Lecturer; Sam Tour, Chairman Institute of Metals Division; and H. Foster Bain, Chairman. Charles F. 'Band Foundation Committee. ' Each was heartily applauded when introduced by Mr. Bridgman, as was Mrs. Tally, who also made a bow. The toastmaster made graceful reference in introducing Mr. Strobel, to the large part the latter had taken in planning the meeting.

Jan 1, 1932

By New kensington P. A, W. L. Fink, H. R. Freche

The investigation of aluminum alloy systems prior to 1923 was severely handicapped by the low purity of the best aluminum available. However, by that time, the electrolytic purification of aluminum had been developed by the Aluminum Company of America,(1)† and in May, 1923, there was initiated, under the direction of E. H. Dix, Jr.,(2) a program for the investigation of the aluminum-alloy systems using the purest electrolytically refined aluminum. Up to the present time 15 papers (3) have been published, most of which are on the binary aluminum systems. Work is now in progress on the ternary systems, and it seems probable that most of the future work will be on ternary systems. Therefore this survey of the binary aluminum systems investigatcd up to the present time (the sixteenth paper of the series) concludes the first phase of this program. Certain qualitative relations between corresponding portions of the various binary diagrams as well as between different parts of the same diagram were noted some time ago by R. S. Archer.(4) In the present paper these relations and others are considered quantitatively by the application of well-known thermodynamic equations or by newly discovered empirical relations. No attempt will be made here to present the history of the development of the thermodynamic equations defining equilibrium or their application to metallic systems, although a list of references is given at the end of this paper for those who are interested in this phase of the subject. Two thermodynamic equations, which will be employed extensively in this paper, are: loge x1 = - L/RT + C

Jan 1, 1934

By Byron B. Morton

NICKEL-BEARING alloys are associated with petroleum in the fields of exploration, production, and refining. In the first- named field the geologist of today makes use of such instruments as the seismograph, torsion balance, and magnetometer, the selection of proper alloys and metals for the manufacture of which is an important matter. Nickel-bearing alloys are useful for parts that require resistance to corrosion or that must have non-magnetic properties. Where special co- efficient of thermal expansion are de- sired, they are obtained by using alloys high in nickel (20 to 60 per cent), since, by varying the nickel contents, alloys can be obtained ranging fro111 "Invar", with a low expansion between -40 and 175 cleg. F., to those with coefficients of expansion exceeding that of steels. The latter are obtained by additions of chromiurn to the alloys. Alloys containing 50 to 80 per cent of nickel, which possess high magnetic permeability, find application in certain instruments where this property is important.

Jan 1, 1935

By Etienne A. Ritter

INTRODUCTION. THE Evergreen mine, located at Apex, in the northern part of Gilpin county, Colorado, has opened a very peculiar and interesting copper-deposit, in which both bornite and chalcopyrite occur as rock-minerals. The country-rocks are crystalline schists cut by dikes of granulite and of pegmatite. At the Evergreen property they have been cut by a dike of a new kind of eruptive rock, to which I have given the name " Evergreenite" The rock is composed of quartz, alkali feldspars, orthoclase and albite (often interlocked as microperthite), with augite of the aegirine variety and long needles of enstatite and diallage. For reasons stated below, I believe the dike to be of Tertiary age. It is- easily traced on the surface of the ground, from a point in the bottom of Pine creek, about a mile below Apex,. to the top of Nevada hill, 1,500 ft. beyond and 600 ft. above it. (See Fig. 1.) It varies from 3 to 12 ft in width, and is bounded on both sides by contact-zones about 60 ft. wide, in which the crystalline schists have been changed into pseudo-quartzites or pseudo-gneisses, according to the injection of an excess of quartz or of feldspars through the special layer of the schists.. The most interesting feature is the presence of the pyroxenes, which are always found, though in very variable proportions from place to place, in the layers of these' metamorphosed crystalline schists. The dike has torn from its walls a large number of fragments of the wall-rock. It must have been in a viscous state when that happened, because these fragments of the wall-rock do not show any sign of resorption or of assimilation by the magma. In places they are so distinct and so numerous that the rock looks to the naked eye like a pseudo-breccia, of which, never-

Jan 1, 1908

By A. E. Outerbridge

It has been generally accepted as a fact that cast-iron, under the influence of repeated shocks, becomes brittle, and will finally break under a blow which otherwise it would have withstood. It will probably surprise metallurgists, therefore, to learn that experiment disproves the supposed fact, and establishes exactly its opposite. The result of about a thousand tests of bars of cast-iron of all grades, from the softest foundry-mixtures to the strongest car-wheel metal, enables me to assert with confidence that, within limits, cast-iron is materially strengthened by subjection to repeated shocks or blows. It is very well known that the usual process of annealing castings—such, for example, as car-wheels—increases their strength by relieving cooling-strains. But it is not well known (if known at all prior to this announcement) that the molecules of cast-iron are capable of movement—for they do not touch each other*—without the necessity of heating the casting, and that they can thus rearrange themselves in comfortable relation to their neighbors, and relieve the overcrowding near the surface of the casting. In more technical words, a molecular annealing may be accomplished at ordinary temperatures which will release the strains in the castings, precisely as does annealing by slow cooling in heated pits or ovens. A statement so surprising should not be made without sufficient data to establish its correctness beyond cavil, since it is contrary to former

Jan 1, 1897

By P. Hazebroek, C. S. Mathews, E. E. Allen, H. C. Lefkovits

A rigorous study was made of the behavior of reservoirs composed of horizontal layers, unconnected except at the well and filled with a compressible fluid. The report is presented in two parts. Part I deals with the practical implications of the results obtained; Part 11 contains the mathematical derivation of the solution. The main portion of Part I is concerned with application of the results to reservoirs composed of two layers. Relative rates of depletion of the layers are studied, and it is shown that differential depletion between layers exists in the transient stage of the reservoir, which generally is of an order of magnitude longer than the transient stage in a single-layer reservoir. In the transient stage, the more permeable layer is depleted faster than the less permeable. However, the reservoir approaches a steady-state situation where both layers contribute equally to production. Theoretical build-up curves from such reservoirs are presented, and the influence of a skin effect and flow into casing and tubing are also evaluated. The build-up curves are predicted to have, first, the familiar logarithmic straight-line section and, subsequently, a rising and flattened section. The results found are compared with an extension of an approximate theory, and it is found that this simplified theory is applicable over most of the life of the reservoir. Extensions to reservoirs containing more than two layers are indicated, and examples of the performance and build-up curves for three-layered reservoirs are presented. The theoretical results on build-up curves were applied to field examples of such reservoirs, and satisfactory results were obtained. From the build-up curve, the pemeability-thickness product, the wellbore damage and the static pressure are obtained. However, it apparently is not possible to determine the properties of the individual layers from the combined build-up curve. A large number of reservoirs have been found where the producing formation is composed of two or more layers of differing physical characteristics, such as permeability and porosity, and where also the thicknesses of the layers differ. Since in general a differential depletion should exist between the layers of such reservoirs, it would be advantageous to know the amount of the differential depletion under a given production history. It also would be valuable to know the pressure behavior, because it could be undesirable to produce a reservoir in such a manner that the pressure in one of the layers would have fallen below the bubble point of the oil at a time when another layer might still be virtually undepleted. The determination of static pressures in shut-in wells with slow build-up is another feature of importance in layered reservoirs. If the behavior of the reservoir differs appreciably from the predicted behavior of a single-layer reservoir, the type of analysis for build-up curves suggested for single-layer reservoirs is not applicable. Several authors have treated the problem of finding the pressure and production characteristics of multilayer reservoirs. Horner treated the problem of n layers in an infinite field, the layers being connected only at the well. Tempelaar-Lietz2 has presented an approximate treatment of the characteristics of a bounded reservoir composed of two layers of different permeabilities and equal thicknesses. Homer gave no information on differential depletion between layers, and the treatment of Tempelaar-Lietz was not applicable for prediction of pressure build-up behavior. In addition, it was thought that a more rigorous treatment than the one by Tempelaar-Lietz would be valuable in determining the range of validity of this solution. The present study, therefore, was made of a bounded reservoir composed of two or more layers,

By G. A. Hellstrand

IN 1915, H. A. Guess, Vice President of American Smelting & Refining Co., in charge of its Mining Department, learned that the Anglo-New-foundland Development Co., Ltd., a pulpwood and paper-mill enterprise, had found upon its large concession in Newfoundland, and had opened up by shaft to the third level and some drifting, a lenticular orebody indicat-ing about 100,000 tons, as an extremely fine-grained sulfide ore, averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn; and that having sent parcels of this ore to Minerals Separation, Ltd., and various other metallurgical testing concerns without obtaining any success in commercial separations thereon, had discontinued work thereon and let the workings fill. Mr. Guess wrote to the general manager of that company and obtained a few hundred pounds of the typical ore, which he sent to his company's metallurgical testing laboratory at Flat River, Mo., outlining various flotation tests desired thereon, in an endeavor to obtain separation into a commercial lead concentrate and a zinc concentrate. But the art of flotation had not then progressed far enough to treat such ore, the galena and zinc blende being so fine grained that grinding to about 300 mesh was required to release the mineral particles in their gangue. Mr. Guess had flotation and other tests continued upon this ore from time to time with whatever new reagents and flotation devices were evolved as time went on, and finally, in 1925, he succeeded in effecting in his company's testing plant, then at Wallace, Idaho, separations into lead concentrates and zinc concentrates of satisfactory commercial grade. Mr. Guess then proceeded to unwater, examine and sample the property and made with the owners a partnership operating agreement upon the mine itself and a considerable area surrounding it, and in the early summer of 1926 began to prospect for additional orebodies, utilizing for such prospecting geophysical methods, under the direction of Hans Lundberg, methods which up to that time had been little used in mining in the western hemisphere.. This geophysical work found two large flat-lying orebodies of a type precisely similar to the smaller body of the original discovery. The larger orebody, some 3500 ft. west of the original

Jan 1, 1934

By Henri V. Reibell

Deep open pit optimization supposes very long and sedious calculations in order to assign the best shape of the pit and the best bottom level, which will give the biggest profit. Computers give the possibility to make these calculations. More over, they allow to multiply trial calculations so that it is possible to obtain more reliable results. The paper does not expose the computer program but only the way in which mining engineers can use it.

Jan 1, 1969

By Waldemar Lindgren

THE following pages present data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks. They also present the individual views of the author on the composition of the solutions that were active and on the mode of deposition. He does not regard these views as speculations or hypotheses but as forming a well motivated and consistent theory. It is not certain, however, that all investigators will subscribe to them.

Jan 1, 1936

By Frank A. Howard

WHAT are the reasons for the present public interest in the synthetic fuel industry, an interest which has culminated in the recommendation of the Secretary of the Interior that we start at once on a nine billion dollar program of construction? Three separate factors seem to have combined to create this pressure. First are recurrent seasonal and spot shortages of gasoline, fuel oil, and natural gas. Second is the international outlook, which forces us to face the possibility of war, with all that means in the way of increased call on our domestic resources and interference with our foreign commerce. The shortages we have experienced are superficially the result of lack of transportation, but basically they reflect a rapidly rising demand which has outstripped the expansion of productive facilities of all kinds. Not only oil and gas, but steel, coal, automobiles, and meat are temporarily in short supply for much the same reasons. The military problem has both long-range and short-range aspects, but the immediate necessity is to create reserve capacity in the United States to supply perhaps 2,000,000 barrels daily additional liquid fuel in time of war.

Jan 1, 1948

By M. R. Stauffer, Z. Hajnal

Seismic velocity determinations over Precambrian outcrops near Flin Flon, Manitoba, indicate that several different rock types have sufficient velocity contrast to make reflection mapping possible. Stratigraphic and fault contacts between metasedimentary and metavolcanic rocks have been mapped at some depth. A mu1ti-fold reflection survey attempted to trace the depth extension of an ore-bearing (Pb-Zn) rhyolite horizon within the metavolcanic rocks. A synthetic seismogram has been produced from a 10,000-ft sonic log and provides means of comparing seismic records with the local geology. From this the optimum frequency spectrum and the maximum resolution of the seismic signals were estimated.

Jan 1, 1978