Search Documents

By D. H. Woodard

One of the principal uses of polarized light in metallurgy is to show the granular structure of metals by contrasting reflections. This use is confined largely to anisotropic metals, such as beryllium, tin, magnesium, and the like.1 Recently, Hone and Pearson2 have extended the use of polarized light to include the isotropic metal aluminum. This was made possible by the formation of an anodic film that was optically anisotropic and that had a fixed and reproducible structural relationship to the grains in the substrata. With their method, it was possible to indicate localized textures in annealed aluminum sheet. In the course of an investigation of plastic deformation at the National Bureau of Standards, it was found that the isotropic single phase alloy Monel could be made optically anisotropic by treatment with the usual Monel contrast etchant. Experiments soon showed that dif- , ferences in orientation could be detected easily. Previous investigations involving the use of polarized light have been restricted to annealed metals. In this paper it will be shown that inhomo-geneous plastic deformation which results in lattice bending and development of deformation bands, experienced by individual grains in polycrystalline Monel, is revealed in the microstruc-ture. This interpretation of the micro-structure was confirmed by a study of slip lines formed after prior plastic strain. Materials and Procedure The material used was Monel, the chemical composition of which was C—0.17 pet, Mn—1.28 pet, Fe—1.61 pet, S—0.009 pet, Si—0.17 pet, Cu— 30.70 pet, Ni—66.04 pet. The material was divided into 2 lots which were treated as follows: Lot A was heated at 1700°F for 3 hr to produce a fully annealed, coarse grained structure. Lot B was heated at 1400°F for 1 hr to produce a close approximation of a fully annealed structure without appreciable increase in the grain size of the original material. After each of these heat treatments the material was cooled in air. Samples for metallographic examination were cut from tensile and compression test specimens and were prepared by grinding on lead-tin laps, followed by electrolytic polishing, † Etching and the development of ridges were avoided by keeping the voltage above 3.8 and by preventing contamination of the polishing solution with water. Monel, when polished and treated with most etchants, is optically isotropic. However, when given a light etch for about 4 sec with the Monel contrast solution the surface of the metal becomes optically active. The microstructure when observed under crossed nicols* appears different from that viewed by ordinary light. This is shown by a comparison of micrographs made of the same area of a plastically deformed specimen using polarized light (Fig la) and white light (Fig 16). If Monel, which has been lightly treated with the contrast etchant, is slightly deformed by compression, rectangular figures are apparent over the specimen. However, within too short a period to be photographed, these rectangles become circular, probably because of surface tension effects within the etched film. The two observations,

Jan 1, 1950

By Albert C. Harding

FOR several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. DESCRIPTION Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare witherite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. OCCURRENCE All known commercially important barite deposits in the United States occur as re placements or cavity fillings in schists, shales, limestones, dolomites, and quartzites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. [TABLE 1-Crude Barite Sold or Used by Producers in 1945 STATE SHORT TONS Arkansas260,660 Missouri225,467 Georgia110,393 Tennessee32,812 Nevada28,919 Other States37,811 Total 696,062] "Other States" included only California and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. CONSUMPTION [The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium -- chemicals Total 720,903 tons]

Jan 1, 1947

G. A. Burr, Parral, Chihuahua, Mexico (communication to the Secretaryt): I regret that Mr. Norris did not give more attention to the hoisting of water in inclined shafts or slopes: the only slope mentioned being Hickory Ridge Slope, No. 4, of the Union Coal Co. The surface arrangement, illustrated in Fig. 12 of his paper, if not unpractical, is at least unscientific and cumbersome. It is my opinion that the back- and sideguides shown in Fig. 12 are not only unnecessary where rails are used as a track, but are unsafe, excepting in the case of a very firm hanging-wall, or roof, and sides of vein-matter, having absolutely no tendency, either to settle from the back, or to squeeze from the sides, an effect which would inevitably force the guides out of alignment. The accompanying illustration, Fig. 1, shows what I consider a better method of hoisting water than that described by Mr. Norris. This method is based on the general practice in metalliferous mines of the West, where skips are used in slopes; and, while it is not original with me, I have frequently used it with very satisfactory results for dumping both ore and water.

Jan 1, 1904

By H. R. Thresh, A. F. Crawley

THIS paper reports the results of viscosity measurements on cadmium and indium undertaken as part of a continuing program of liquid metals research at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. For several years this work has continued with support from the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. In the literature, existing viscosity data for cadmium are conflicting and for indium are scarce. To achieve reliable viscosity values, further work was deemed desirable. Viscosities were measured using an absolute technique applied to an oscillating closed right cylinder of liquid metal. The apparatus, constructed in this laboratory, and the techniques involved in its use have been described in an earlier paper.' In calculating viscosity coefficients from the experimental data. Roscoe's2 mathematical analysis was used. Because accurate viscosity determinations are dependent on accurate density data, and since the available data in the literature are conflicting, the densities of liquid cadmium and indium were also determined in this laboratory by a pycnometric technique. This increased the control exercised over all the variables contributing to the accuracy of viscosity measurements. For both density and viscosity determinations, cadmium and indium of 99.999 pct purity were used. These materials were obtained from Cominco Ltd. In order to suppress excessive evaporation losses and help prevent oxidation, a technique developed in measuring the viscosity of zinc' was used for cadmium. This involved maintaining an atmosphere of purified hydrogen in the viscosimeter during the rela- tively long periods while the experimental temperature was changed and stabilized between individual determinations of the logarithmic decrement. Then, immediately prior to a decrement measurement. the viscosimeter was rapidly evacuated to a pressure of about 2 X 10-6 torr. On the other hand. with indium. no difficulties arise from vaporization or oxidation. In this case. therefore. the apparatus was held under a constant vacuum of about 2 x 10-6 torr. When all sources of random and systematic error have been evaluated, the technique is considered to yield data accurate within 10.5 pct. The viscosity of cadmium was measured to a maximum temperature of 451.8°C and that of indium to 346.5°C. These temperatures are. respectively. 130° and 190°C above the melting points. Two separate runs were made on indium. The results are given in Table I and, when plotted. yield the smooth curves evident in Figs. 1 and 2. Values of A and C to fit the well-known Andrade1 equation were determined by a regression analysis. The equation is: where n = coefficient of viscosity. i = specific volume. T = temperature in °K Despite its empirical nature. Andrade's equation has been shown by many workers to describe accurately the temperature dependence of viscosity. During the current research program, this equation has been found to fit the data precisely for all the metals and alloys that have been studied.5,6 The A and C' values for cadmium and indium are given in Table 11. Comparing the magnitude of the present data with those of previous workers,7-10 as has been done in Fig. 1, it is evident that the results of Fisher and Phillips10 deviate markedly from the rest. With the exception of one point from Gering and Sauerwald,7 all other data agree within ±2.5 pct. However, the agreement between the present results and the work of Menz and sauerwald9 is especially good over the entire experimental temperature range. Such agreement may be expected since Menz and Sauerwald's

Jan 1, 1970

By AIME AIME

THE section delegates assembled Monday morning with the incoming president, W. H. Bassett, in the chair and F. W. Bradley as vice-chairman. The secretary called the roll and urged the delegates to become familiar with the activities of the Institute. He explained the allotment of funds to local sections and the uses to which these funds may be put. He also announced plans for travel by Mr. Bassett and asked the delegates to confer with him as to meetings en route. An invitation was extended for all section delegates to attend the Directors' dinner Wednesday evening. He suggested that local sections hold a meeting once a year under the auspices of each division of the Institute. He further explained the system of choice of publications by members. The question of licensing of engineers was brought up, and the consensus of opinion among the membership was asked for. Because the matter is controversial, no official action has been taken and it was suggested that the' local and State sections act separately in this regard. A. B. Parsons, the assistant secretary, next spoke. In his remarks he indicated surprise that many prominent mining men still did not belong to the Institute, and urged that section delegates make up a list of such prospective members and send it in to the office for study by the New York staff. He also asked that re- ports of all meetings be turned in for publication in MINING AND METALLURGY, and said that the reports

Jan 1, 1930

By E. F. Adkins, R. I. Jaffee, C. T. Sims

The effect of oxide dispersions on mechanical proberties of cobalt and cobalt-base powder-metallurgy alloys was investigated. This study shows that oxide dispersions added to pure cobalt greatly improve the high-temperature creep resistance of the metal. Dispersions in powder-metallurgy .cobalt alloys were muck less effective. COBALT is extremely valuable as an alloy base for certain high-temperature applications. Important examples may be found in the widespread use of cast and workable alloys in aircraft gas-turbine engines. With the increases in cobalt production in recent years, greater use may be made of cobalt-base alloys for high-temperature applications, provided

Jan 1, 1960

By Glenn A. Keep

THIS paper is not an announcement of the successful conclusion of the Cerro de Pasco Copper Corporation's pacos-pyrite problems, but merely a description of the commercial-scale, intermittent-roasting operations conducted by the writer, J. H. Lucas and others of the staff. It was prepared by request, for presentation at the February meeting of the Institute. The results obtained in Peru confirm the 1-ton-a-day experiments completed about three years ago at Kearny, N. J. by C. C. Gordon and Mr. Lucas, where it was first demonstrated that a mixture of about 80 per cent. pacos ore with 10 per cent. pyrite ore and 10 per cent. salt could be roasted intermittently in a small 1-ton-a-day Holt-Dern furnace without extraneous fuel, producing porous calcine that could be leached rapidly. Mr. Keep and his staff, by successfully introducing improvements in the construction of the commercial furnace and in their handling of material, have established beyond doubt a low cost for roasting. The other steps in the process of treating pacos and pyrite ores have not as yet been demonstrated as sufficiently conclusive to warrant their acceptance for a permanent plant. Cerro de Pasco Ores The ores of the Cerro de Pasco Copper Corpn. at Cerro de Pasco, Peru, are situated at an altitude of 14,000 ft. The town and mines are served by the Cerro de Pasco Railroad, which operates between Cerro de Pasco and Oroya, the site of the company's copper and lead smelters. Table 1.—Average Analysis of Cerro de Pasco Ores Pacos Ore Pykite Ore Silver, oz............................................... 10.3 12.0 Gold, oz................................................ 0.007 0.01 Lead, per cent........................................... 1.7 1.8 Copper, per cent......................................... 0.19 0.27 Zinc, per. cent........................................... 1.4 1.02 Iron, per cent........................................... 13.4 34.45 Silica, percent.......................................... 61.8 24.5 Alumina, per cent....................................... 2.5 0.62 Lime, per cent........................................... 1.5 0.20 Manganese, per cent..................................... 0.42 0.09 Sulfur, per cent,.......................................... 1.1 34.2

Jan 1, 1929

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, killed in action. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M., killed in action on October 12, 1917. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service. Hall, William T., Capt., Royal Flying Corps, killed in action. Heine, Bernhardt E., Lieut., Aviation Service, killed at Fort Sill, Okla., Aug. 10, 1918. Irving, John Duer, Capt., 11th Engineers, A. E. F., died while on active service in France on July 26, 1918.

Jan 9, 1918

By H. M. Fisher, R. E. Snow, S. C. Sun

SEVERAL constructive and fundamental studies have been made in the analysis of data obtained from experiments carried on with batch ball and rod mills. The operating characteristics of ball milling in small continuous circuits have also been appraised. It is from these analyses that some of the theories of comminution have been developed. Relatively few studies of continuous rod milling have added significantly to the fundamental concepts, because seldom have they yielded sufficiently consistent results. Perhaps they have been too limited in their scope. Careful control of the variables in batch grinding is simple compared with that encountered in a continuous operation. This factor alone has discouraged many investigators. Occasionally results of systematic changes made in industrial rod mill circuits have been published, but usually the data are sketchy and are restricted because of the unwieldiness of the equipment used. The work, in general, has not been comprehensive; nevertheless it has provided empirical relationships that have bridged the gap between postulate and practice so that by proper manipulation of formulae, a mill designer can anticipate mill size and power requirements.14 Although operating variables of a small continuous mill are not so easy to control as with the batch mill, with present day devices, and with careful experimental work, consistent results can be obtained. Nearly four years ago, in the Process Laboratory, Allis-Chalmers Mfg. Co. began a systematic study of the effects of several variables upon the performance of the pilot rod mill. A mill was built in the laboratory to provide the versatility required for the proposed study. It was constructed in sections so that it could be operated, with a few modifications, as a rod mill 30 in. x 8 ft or 30 in. x 4 ft. The discharge end of the shell was flanged so that either an end peripheral discharge or an overflow discharge could be installed. Thus the performance of at least four types of mills could be studied merely by changing the type of discharge or the length of the mill shell. The grinding experiments were designed so that a study could be made of the way in which the mill speed, feed rate, and pulp density influenced the performance of both overflow and end peripheral discharge rod mills. Four sets of experimental data were collected from the four mill arrangements. The mill in each set of experiments was fed at four rates of feed depending on the length of the mill, at four pulp densities, and at five percentages of critical speed. Electrical and mechanical controls were in- stalled to regulate all these independent variables, and auxiliary devices were used to verify the precision of the controls at each point. The dependent variables used to quantify the experiments were the reduction ratio and the hew surface area produced as calculated from sieve analyses. These were incorporated with the energy factor by the calculation of both the new surface produced per unit of energy and the Bond work index.' Rod wear, as a dependent variable, was not studied because of the short period of operation for each run. Exclusive of repeat runs, each set of experiments yielded 80 products, and the total study at least 320 products, all of which were quantified. With the operating information collected, these data presented a bewildering accumulation. Statistical analysis has been invaluable in unraveling the confusion and in presenting a means of establishing the nature and the magnitude of the significant variables. Data presented in this paper are those from the 30 in. x 4 ft end peripheral discharge rod mill, Fig. 1, when limestone was ground at feed rates of 1000, 2000, 4000, and 5000 lb per hr, at pulp densities of 50, 60, 70, and 80 pct solids, and at mill speeds of 50, 60, 70, 80, and 90 pct of the critical speed. These 80 tests have all been run at least twice, and occasionally a third time, to prove that the data obtained were reproducible. The techniques of operation and the methods of quantification of results are described in the following pages and the results analyzed statistically to show the significant variables. The variables are plotted to show the relationships that exist. A massive dolomitic limestone from Waukesha Lime and Stone Co. was used for feed during these experiments because of its availability and its tex-tural uniformity. This limestone analyzed 28.7 pct CaO, 21.0 pct MgO, 6.0 pct SiO2, 0.4 pct A1²O³, and 0.3 pct Fe²O³ and had a loss on ignition of 44.1 pct. It had a rod mill grindability at 14 mesh of 9.6 grams per revolution from which a work index of 13.9 was calculated. The ball mill grindability at

Jan 1, 1955

By A. H. Grobe, F. N. Rhines

THE constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conventional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitution of its alloys desirable. As a part of a program for the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram [ ] (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (143.5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By David B. Reger

The year 1936 in West Virginia was characterized by increased activity in natural gas. The number of actual completions was only slightly increased but many more wells were drilling than at the end of 1935 and there was almost feverish activity in taking new leases. This pronounced revival is partly due to the fact that the extremely cold winter of 1935-1936 showed that additional supplies of gas would be desirable and partly to the hope of finding new pools in the deeper sands. No new pools have actually been found, but the Oriskany sand (L. Dev.) development of Kanawha County, which was already assured by the end of 1935, was greatly extended into wider and richer territory. The Middle Devonian shale (Childres sand), reached incidentally by Oriskany exploration as well as by direct design, has been productive of gas in much wider areas of Boone, Lincoln, Putnam and Kanawha Counties than heretofore known. Routine drilling to the upper sands in dehed territory, also, was greatly increased, although not yet much reflected in completions. Thc supply of marketable gas, however, has been substantially enlarged. In preparation for further exploration there has been an extensive leasing campaign throughout the entire territory where gas seems at all probable, or ever possible. Exact figures are lacking, but new leases have certainly been taken on more than 1,000,000 arres. One operator estimates that 500,000 acres have been leased in the Appalachian geosyncline alone between Parkersburg and Charleston. Exploration, both for shallow and deep-sand gas, on some of these new leases is now under way. There was little activity in oil. No special search for new pools was made and none was found, but the usual routine drilling in old pools occurred. One major gas pipe-line enterprise was undertaken and completed. Operating technology was much the same as usual. In certain localities repressuring for oil has become a matter of routine, and in others the use of acid in treating small wells in calcareous beds has been continued. Financially, the year has been eventless. Some attempts to buy and

Jan 1, 1937

By J. C. McDonald

A DDITIONAL experimental data are presented in this note on a phenomenon which has been touched on but lightly in the literature. The common magnesium base rolling alloy (AZ31B) contains about 3 pet A1 and 1 pet Zn. When cold rolled, it hardens until it starts to break up in the rolls at 30 to 50 pet reduction. When it is heated after rolling to full hardness, it softens. However, other magnesium alloys have shown themselves capable of being cold rolled indefinitely, provided the ratio of roll diameter to starting gage is sufficiently high. As measured by the tensile test, these alloys actually soften when the reduction becomes large (60 to 90 pct). A subsequent heating at 300' to 500°F can produce hardening of this metal. Heating at higher temperatures (600' to 800°F) causes recrystalliza-tion and softening. Menzen' has shown that a magnesium base alloy can be cold rolled without intermediate anneals as much as 90 pet. The alloy studied, Mg-1.5 pet Mn, softened considerably between 20 and 90 pet reduction, as measured by tensile properties; a decrease in yield strength of 30 pet, and an increase in elongation from 3.2 to 16.7 pet (longitudinal direction of the sheet). However, Menzen gives no data on the reaction of this metal. to heating. Ansel and Betterton2 and Hurst and Hatch3 report a similar effect in Mg-1.5 pet Mn-0.1 pet Ca. Their data show an initial hardening, followed by softening. The former authors also show that the alloy softened by cold rolling will harden when heated at low temperatures, and that these effects are absent in Mg-3 pet Al-1 pet Zn. In the course of work4, 5 some years ago, the author observed similar effects with alloys containing cerium, thorium, or zirconium; but not with elements like aluminum, silver, or zinc. Table IA contains the results of an experiment which shows these effects rather well. A binary alloy with 0.3 pet total rare earths (Mischmetal* added) was rolled hot to 1/16 in. and then annealed to full softness by heating 30 min at 800°F. Rolling was continued at 1.5 pet per pass to 80 pet total reduction on 8 in. diam rolls. The metal was harder after 20 pet work than initially but, at 80 pet reduction, properties were back to their original values. Heating for 1 hr at 450°F produced about the same hardness whether the reduction was 20 or 80 pet. At intermediate reductions, the metal hardened, but not to as high values. Extensive cold rolling may also be carried out on metal hot rolled at temperatures sufficiently low to produce a semihard temper. Mg-0.6 pet Zr was rolled to 0.1 in. at 700° to 800°F, 30 pet per pass. As shown in Table IB, a further cold reduction of 85 pet, at 1.5 pet per pass, definitely softened the metal.

Jan 1, 1959

THE paper on "Cross-cuts in Coal Mining," by J. J. Rutledge (published in MINING AND METAL-LURGY, February, 1927, p. 64) was brought up for discussion at the annual meeting, where the follow-ing comments were made T. D. Thomas (Lehigh Coal & Navigation Co., Lansford, Pa.) : This question has caused me a lot of worry, not in the particular district in which I am, but throughout other districts. There are always several angles to consider. If you are in a hurry to push development work, you might increase the distance between cross-cuts from 60 to 350 ft., but if you have a 40-ft. chain pillar every 60 ft. it will cut down your entry driving a whole lot. Looking at it from the ventilation angle, I agree that too many cross-cuts in entries are bad things. You have a tremendous amount of leakage, and I have seen currents starting out with 45,000 cu. ft., and after passing about 30 or 40 cross-cuts the current has dwindled down to about 18,000 or 15;000 cu. ft. The result is that the question of putting in auxiliary fans is raised. That involves several points into which I do not want to go too far, but I am in favor of not getting in too many cross-cuts, putting them in only where they are necessary: I think the state mining laws are wrong in a number of places on that, and that when you finish with a cross-cut it should be in the room. It should be well sealed on an entry. There are several ways of tightening up the cross-cuts so as not to have the great amount of leakage and wastage of: air that we now have. 'I prefer tile stopping; other people prefer cement or brick, but there is a big fac-tor to all mines, saving the mine. I checked up on the number of fans in the anthracite region and found there are 651. That was derived from the state report of 1921, and it enabled me to compute from the power the weight of the air. In the anthracite region of Pennsylvania we put in 9 tons of air to every ton of coal we get out. Tracing that back again and taking the Government's figures which they made some time ago, I found but 20 per cent of the air got to the faces where it was actually needed. That is a tremendous big loss and shows a possibility for saving, money for the various coal companies. Chairman Rice: I think what Mr. Thomas refers to was an investigation by R. Y. Williams, of the Bureau of Mines in Illinois, where a study was made of 100 typical mines, and, speaking off-hand, my recollection is that we found as little as 15 per cent of air reached the faces in one of the mines and another was as much as 50. That seems to be a reflection on the type of stoppings and general ventilation scheme.

Jan 3, 1927

By M. R. Tek, K. H. Coats, D. L. Katz

The performance of a gas reservoir su,bject to water drive is often affected by interference due to gas procluction or injection in neighboring reservoirs adjacent to a common aquifer. Field data available on production-pressure behavior of several reservoirs indicate that prediction of reservoir performence must include the effects due to mutual interference. A method developed to predict the performance of two or more interfering gas reservoirs, subject to specified production-iniection .rchedule.s, is presented. The method involves the comhinatiorz of the theory of unsteady-state water movernent with appropriate meterial balance consideration.s. The procedure which extends M. Mortada's treatment for interfering oil reservoirs makes use of his dimen-.sionless pressure drop quantities. prevented graphically in the literature. In order to evaluale the predictive accuracy and practical field applicability of the theory, the method has been applied to analyze the performance of two actual gas reservoirs in mutual interference. The calculations were performed on an IBA4 704 computer. The predicted performances were alro calcltlated with the interference effects ignored. The results show that considerably better agreement between calculated and observed behavior ic. obtained when the interference effects are included. INTRODUCTION Fluid communication between any number of oil or gas reservoirs adjacent to a common aquifer results in mutual interference effects on their production-pressure behavior. The theory, application and interpretation of pressure build-up behavior of oil wells, drawdown tests on oil or gas-producing formations and behavior of several storage reservoirs indicate ample experimental evidence of mutual interference. A method developed to compute the behavior of interfering oil reservoirs was published several years ago by Mortada.4 Studies conducted during the recent years on underground storage of natural gas clearly indicated the need for extending Mortada's work to the case of interfering gas reservoirs. The adoption of appropriate material balance equations in conjunction with the unsteady-state pressure interference theory yields pressure-explicit equations. Their solution, their application to a specific case history and an over-all evaluation of the developed method through the comparison of predicted and observed field performances were the main objectives of this study. DEVELOPMENT OF MATHEMATICAL RELATIONS The diffusivity Eq. 1 governs planar, radial, unsteady-state compressible liquid flow through a porous medium. ?p/?r2+1/r ?p/?r=µFc/k ?p/?t (1) The 1iterature1,2,3 contains derivations and solutions of

By O. C. Wheeler

In past years the exploration of the oil possibilities of Colombia has been confined to parts of three distinct physiographic provinces; namely, the coastal plains area near the Caribbean Sea, the Magdalena Valley and the upper reaches of the Maracaibo Basin near the Venezuelan border. During 1935, little exploratory work and no drilling was carried on on the coast, but there was considerable activity in the other two areas. In the Magdalena Valley, the Tropical Oil Co. continued its producing and development operations on the De Mares Concession. The Socony-Vacuum exercised the option it acquired in 1934 on Sr. Luciano Restrepo's concession adjacent to the Tropical property and north of the Sogamoso River. No wells have been started on the Socony's lands although, according to the terms of the lease, drilling must be started within the next two years. West of the Carare River and adjacent to the Tropical's southwestern boundary, the Sociedad Nacional del Carare denounced the lands formerly held by the Union Colombiana, whose lease automatically lapsed during the year owing to the company's failure to comply with its drilling obligations. In the same area, the concessions held by Callejas et al. and the Société Européene des Pétroles are also understood to have lapsed for the same reason. Holdings of other interests in the Magdalena Valley were inactive during the year. Near the upper part of the Maracaibo Basin, the Gulf, through its subsidiary the Colombian Petroleum Co., continued active exploration and development on its Barco concession. Colombian Petroleum Co.—The following information and that presented in the accompanying tables relating to the activities of the Colombian Petroleum Co. was supplied through the courtesy of Mr. E. S. Bleecker, chief geologist of that company. Four wells were completed during the year on the north Petrolea dome, where an attempt is being made to define the limits of the field. On the south end of the Petrolea anticline, one well, Petrolea No. 3, which might be classed as a wildcat, encountered a heavy flow of salt water immediately below the oil zone and had to be abandoned. A second location has been made 1 miles south of No. 3 and somewhat higher on

Jan 1, 1936

By O. C. Wheeler

In past years the exploration of the oil possibilities of Colombia has been confined to parts of three distinct physiographic provinces; namely, the coastal plains area near the Caribbean Sea, the Magdalena Valley and the upper reaches of the Maracaibo Basin near the Venezuelan border. During 1935, little exploratory work and no drilling was carried on on the coast, but there was considerable activity in the other two areas. In the Magdalena Valley, the Tropical Oil Co. continued its producing and development operations on the De Mares Concession. The Socony-Vacuum exercised the option it acquired in 1934 on Sr. Luciano Restrepo's concession adjacent to the Tropical property and north of the Sogamoso River. No wells have been started on the Socony's lands although, according to the terms of the lease, drilling must be started within the next two years. West of the Carare River and adjacent to the Tropical's southwestern boundary, the Sociedad Nacional del Carare denounced the lands formerly held by the Union Colombiana, whose lease automatically lapsed during the year owing to the company's failure to comply with its drilling obligations. In the same area, the concessions held by Callejas et al. and the Société Européene des Pétroles are also understood to have lapsed for the same reason. Holdings of other interests in the Magdalena Valley were inactive during the year. Near the upper part of the Maracaibo Basin, the Gulf, through its subsidiary the Colombian Petroleum Co., continued active exploration and development on its Barco concession. Colombian Petroleum Co.—The following information and that presented in the accompanying tables relating to the activities of the Colombian Petroleum Co. was supplied through the courtesy of Mr. E. S. Bleecker, chief geologist of that company. Four wells were completed during the year on the north Petrolea dome, where an attempt is being made to define the limits of the field. On the south end of the Petrolea anticline, one well, Petrolea No. 3, which might be classed as a wildcat, encountered a heavy flow of salt water immediately below the oil zone and had to be abandoned. A second location has been made 1 miles south of No. 3 and somewhat higher on

Jan 1, 1936

By J. P. Neumann, Y. A. Chang

Lattice parameter measurements of the hcp phase in the system Ag-A1 near the stoichiometric composition Ag2Al were carried out for specimens quenched from 825°K, annealed for 10 days at 453°K, and annealed for 100 days at 413°K. The three heat treatments resulted in the same lattice parameters at room temperature. None of the specimens showed any superlattice lines. The lattice parameters of this alloy were also measured at temperature from 77° to 750°K. An anomaly in the temperature variation of the lattice paramete.rs occurs in the region near 400°k, which may be associated with local ordering. FROM measurements of the diffuse scattering of X-rays, it is known that the [ phase in the system Ag-A1 near the stoichiometric composition Ag2A1 ex- hibits a considerable degree of short-range order at room temperature.' Moreover, based on the position of the short-range order peaks a superlattice model had been proposed in the same study and it was suggested that lowering the annealing temperature to 420°K might result in long-range order. In the present study, the diffraction patterns and the lattice parameters of three differently heat-treated specimens, i.e., quenched from 825°K, annealed for 10 days at 453°K, and annealed for 100 days at 413°K, were determined from 77" to 750°K. The purpose of these measurements was to investigate 1) whether long-range order could be established by prolonged annealing and 2) whether the lattice parameters at room temperature depended on the heat treatment, since it had been proposed earlier2 that the lattice parameters in this phase are related to the atomic arrangement. 1) EXPERIMENTAL TECHNIQUES Silver and aluminum, both 99.99 pct purity, were melted in a zirconium oxide crucible under helium in

Jan 1, 1969

Discussion of the paper Of NOEL CUNNINGHAM, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 601 to 608. C. H. POIRIER, New York, N. Y. (communication to the Secretary*). -Mr. Cunningham's paper, written from the standpoint of a stamp advocate, while commenting more or less favorably upon the installation of ball mills in the Vipond plant, does not, in my opinion, give as much emphasis to the comparatively new departure as the installation of ball mills in the place of stamps justifies. This discussion is based upon my personal and intimate practical work for several years with stamp mills, and for the past three years with Hardinge ball and pebble mills. The fact that the Vipond mine contains about equal quantities of the A and B classes of ore mentioned by Air. Cunningham, and the further fact that I have had a most intimate knowledge of the working of both classes of ore in the Porcupine district in stamp mills and ball mills, justifies upholding my final decision to use ball mills in the place of stamps, and defends my present further action in now increasing the present Vipond capacity by the addition of another 6-ft. Hardinge ball mill, in which action the directors of my company concur. This is one of the strongest evidences I can possibly offer in substantiation of my opinion that the ball mill exceeds the efficiency of the stamp, both in metallurgical and mechanical economy. It is hardly fair to compare a 100-ton per clay plant with a mill handling several times this amount, yet it is my belief that the cost per ton. of grinding in the ball mill is far less than that of any stamp mill in the district, where capacities run up to 400 tons per clay.

Jan 5, 1915

By C. E. Shoenfelt

The deepening of the General Crude Oil Company's No. 1 Meyers, NE. NE. SE. of sec. 22, 24S., 36E., in the Cooper area of Lea County, in April, 1934, resulted in the discovery of an oil field of major importance. The discovery well is an old well drilled by Cranfill $ Reynolds and completed in July, 1929, in limestone at 3438 ft. for an initial production of 90,000,000 cu. ft. (estimated) of 'gas. Deepening operations were started early in April, 1934, and cores were taken from the old total depth of 3438 to 3508 ft. A Haliburton test taken through the drill stem at 3439 to 3460 ft. showed 50,000,000 cu. ft. of gas with an increase of 5,000,000 cu. ft. between 3461 and 3474 ft. When completed the well tested 12,000,000 cu. ft. of gas and 5000 bbl. of oil at 3474-3508 feet. The new oil field—the result of this discovery—is between the Eunice and the Jal fields, closer to the productive area of Jal than to that of Eunice but far enough away from both to be considered a separate area. Eventually, all of these pools may be joined together by productive oil wells to form a single unit of large size. They lie in a general northwest-southeast alignment and the intervening areas have not been condemned by dry holes. In the drilling campaign that followed this discovery, 24 wells were drilled, of which 23 were oil wells with combined initial productions of

Jan 1, 1935

By E. W. Krampert

Oil development continued active in Wyoming during 1937, with much of the interest centered on prospecting for new pools, following a rather intensive seismograph play in 1936. The new fields of Lance Creek, Medicine Bow and Quealy were the centers of intense development in proved areas, but routine drilling occurred in most old fields. A new and deeper producing horizon (the Leo sand) was opened up in the Lance Creek field, which materially extends the producing area and will probably account for continued active development during 1938. The discovery in 1936 of oil in the Eocene Wasatch formation at Powder Wash, northwestern Colorado, tended for a time to stimulate prospecting in the deep Tertiary basins, but this interest as rapidly declined after drilling several failures on similar structures and the discovery that the productive area at Powder Wash itself was very small. A most interesting test of an Eocene structure was drilled by The Superior Oil Company of California on the South Baggs structure, in Carbon County, Wyoming. South Baggs is one of the best developed structures in the Red Desert Washakie Basin, which also includes the Hiawatha gas field and the Powder Wash gas and oil field. The Superior Oil Co. started the well according to contract but apparently had lost interest in the prospects, for it abandoned the well at 2138 ft. without testing the oil-bearing and gas-bearing horizons of the Wasatch. The Sinclair Wyoming Oil Co. drilled a deep test in the Muskrat gas field to the Madison. This well discovered oil in the Embar formation, which was considered noncommercial because of depth. After the Embar was abandoned the hole was plugged back and the various sands tested by shooting through the casing with the Lane-Wells gun. The Lakota sand was found to contain high-pressure gas and the well was completed as a 24-million-foot gasser at 2175 lb. rock pressure. This is a new sand in an old field. The Italo Petroleum Co. drilled a flank well on the Hamilton dome structure and found oil in the lower Embar formation. Thk merely extends the limits of production, as one old well on the structure had

Jan 1, 1938