Search Documents

By Nicholas J. Grant, Noboru Komatsu

Electron-micrographic studies and hardness tests were made of an internally oxidized dispersion-strengthened Cu-12 vol pct SiO2 alloy follozuing longtime annealing at elevated temperatures. The rate of coarsening of SiO2 particles and the relationship between hardness and interpavticle spacing were Dispersion -strengthened alloys exhibit a remarkable stability of structure and properties at elevated temperatures compared with conventional alloys; nevertheless, when they are exposed to high measured. The rate of coarsening of SiO2 particles is controlled by the decomposition of SiO, rather than by the diffusion rates of silicon or oxygen through the copper matrix. The mechanism of coarsening was also studied by using a diffusion-couple technique. temperatures, weakening takes place as a result of coarsening of the dispersed phase. The theoretical treatment of the coarsening of dispersed phases has been treated by Greenwood,1 wagner,, and others3 by considering the interfacial energy of dispersions and the diffusion of solute atoms. Recently, experimental work on the coarsening of relatively insoluble, finely dispersed cobalt particles in copper was reported by Livingston,4 and on aluminum oxide in nickel by Dromsky, Lenel, and Ansell;5 according to these investigations, the rate

Jan 1, 1964

By V. H. Wilhelm

The outstanding event in the California petroleum industry during 1931 was the continuance of curtailment of crude oil production, which directly reduced drilling and well repair activities. Although all objectives were not attained, a very close balance between supply and demand was maintained during the period of maximum requirements, but the decline in intercoastal and export shipments caused an overproduction during the last half of the year, which indicated that California production would necessarily suffer further curtailment after the end of the year. A new peak in potential crude oil production of 1,187,600 bbl. per day was reported in August and at the close of the year the California potential was 1,069,000 bbl. per day, the shut-in light oil amounting to practically 425,000 bbl. per day and the shut-in heavy oil amounting to about 150,000 bbl. per day. Fig. 1 depicts these conditions and also shows the production and curtailment situation since the inception of proration in California. The December, 1931, potential figure of 1,069,-000 bbl. per day was arrived at after the most careful deliberation by a number of committees, selected to check the potential of practically every well in the state. Continued overproduction in the first three months of 1931 and the inadvisability of building more storage, together with the inability to obtain the proper amount of curtailment in town-lot fields, such as Long Beach, Santa Fe Springs and Playa del Rey, prompted the major oil companies to inaugurate a price reduction in crude oil. This cut caused prices to reach the lowest levels since 1915, and instigated the formation of an oil sales agency, composed of independent operators, which is known as the Oil Producers Sales Agency. The purpose of this organization is to procure a market for its members at reasonable prices, advise them of market conditions and aid them in controlling the amount of oil available for sale. Marketing of oil produced by members began on June 1 and independents controlling" about 160,000 bbl. per day of production had become members by the end of the month.

Jan 1, 1932

By E. O. Wagner, V. F. Parry, W. S. Landers

Following investigations by the Denver Bureau of Mines on drying fine coal in the entrained state, Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help off- set the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee, and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal, but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used.

Jan 1, 1956

By B. J. Bayles, J. A. Ford, M. J. Salkind

Unidirecltonally sulidijied AL-A13Ni was found to exliibit excellent microstructural stability to 508°C. Above this temperature the transverse micvostructure coarsened in a manner analogous to "Ostwald Ripening", but the A13Ni whiskers did not spheroidize or foreshorlen. The coarsened whiskers reinforced the matrix as effectirely as the finer whiskevs and no reduction in room-temperature tensile strength mas noled after exposure for 90 hr at 96 pel 0-1 the absollite melling temperature of the eulectic. The slability was auribucted to the presence of low-index (and presurrlably lor-energy) cvystallographic interjaces between phases. The driving force for microstructural coursening was presumed to be the reduction of interfacial energy between the phases. Finer micvoslructures were found to coarsen more rapidly than those which weve imitally coarser. FIBER-reinforced metals have been shown to exhibit good short-time tensile properties at elevated temperatures.1-4 However, many elevated-temperature applications require long-time property retention which dictates the necessity for microstructural stability. Two types of instability are common to fiber composities. The first, chemical instability, is due to chemical reaction between the matrix and the relnforcing phase. Petrasek and weeton5 have shown that chemical reaction between tungsten wire and several copper alloy matrices resulted in degradation of the reinforcing phase and reduction in strength of the composite materials. Kreider and Leverant4 have noted similar behavior for boron-reinforced aluminum above 400°C. The second type of instability arises in systems in which the phases are essentially chemically stable with respect to each other and is characterized by spheroidization and/or agglomeration of the reinforcing phase. parratt6 has reported this type of degradation to occur relatively rapidly at moderate temperatures for nickel and cobalt alloys containing whiskers of silicon nitride, aluminum oxide, and silicon carbide and has identified it as "physicochemical" instability. Although both types of instability are the result of the differences in the chemical potential between the fibrous phase and the matrix, they may be differentiated by the fact that the second type, "physicochemi-call' instability, results in little or no net change in the composition or amount of each phase present. It does, however, result in a morphological change which profoundly affects the strengthening mechanism. Chemical interaction. on the other hand, results in a change in the composition and amount of one or more of the phases present, or the appearance of a new phase. In the latter case, the appearance of the mi-crostructure, that of a fibrous phase aligned in a matrix, may remain essentially unchanged, but the chemical degradation of the fiber results in markedly reduced composite strength. This investigation was initiated in an attempt to evaluate the microstructural and related mechanical property changes of a whisker-reinforced eutectic composite after elevated-temperature exposure. The composite system chosen for this study was the uni-directionally solidified A1-A13Ni eutectic which Lemkey. Hertzberg, and Ford7,8 demonstrated to behave as a whisker-reinforced composite. The microstructure of the unidirectionally solidified material consists of aligned needles of A13Ni in a matrix of aluminum. EXPERIMENTAL PROCEDURE Eutectic ingots having a nominal composition of 6.2 wt pct Ni were produced by melting 99.99+ pct A1 and 99.99 pct Ni in recrystallized alumina crucibles in an argon atmosphere. The analyses of the starting materials are listed in Table I. These master heats were cut up? melted by induction heating, and unidirectionally solidified vertically in 1/2 -in.-ID. 6-in.-long graphite crucibles, in a dynamic argon atmosphere. Therma1 gradients in the liquid were determined by measuring the temperature in the melt as a function of apparatus travel distance, as discussed by Kraft and Albright.9 The rate of solidification was assumed to be equal to the uniform rate at which the crucible assembly was withdrawn from the furnace. Ingots representative of nominal growth rates of 2, 5, and 11 cm per hr were produced and the solidification parameters are summarized in Table 11. Ingots used for met allographic analysis were pre-

Jan 1, 1968

By Warren Howes, C. O. Anderson, Robert E. Illidge, M. D. Harbaugh, S. J. Burris

The Tri-State zinc-lead mining district embraces an extensive area, including the northeastern part of Ottawa County, Oklahoma, the southeastern part of Cherokee County, Kansas, and adjacent portions of Missouri, mainly in Jasper County. The Oklahoma-Kansas portion of the district, in the vicinity of Picher, Okla., has been the principal producing area since 1917, and the present milling practice in that section is the subject of this paper. This district is the largest zinc-producing field in the United States. In 1926 it produced 55 per cent of the nation's zinc and 15 per cent of its lead, and in 1933 it produced 35 per cent of the zinc and 10 per cent of the lead. From 1842 to 1933, inclusive, the total output of the district was 18 1/2 million tons of zinc and lead concentrates valued at 818 million dollars. Of this production, the Oklahoma-Kansas, or Picher, field yielded over 9 million tons valued at over 400 million dollars. Mining operations in the Oklahoma-Kansas field near Picher and Baxter Springs began in 1915. The mills built it that time consisted merely of gravity concentration plants employing jigs and tables and the same flow sheets as had proved satisfactory with the free-milling ores such as were mined in the Joplin-Webb City fields in Missouri. The Kansas-Oklahoma ores proved to be much richer but also more refractory to treatment than those in the Joplin area, and contained a considerable percentage of zinc mineral not freed by the amount of crushing usually practiced in preparing the ores for jigging. Thus the old Joplin type of mill, with its usual two or four jigs and a few tables, proved inadequate and resulted in excessive tailings losses sometimes as high as 50 per cent

Jan 1, 1935

By D. M. S. Bhatia, Richard D. Hagni

Five sulfide minerals from the Magmont mine, southeast Missouri were sampled for 31 trace elements in over 300 samples by laser microprobe spectrographic analysis of polished sections. The concentration of several trace elements shows a pattern of progressive variation with depth (space) and variation with different paragenetic stages (time) of each mineral. Factor analysis of the geochemical data shows sympathetic correlation both in space and in time of Bi, Cd, Ge, and Sn in galena and sphalerite, and Ni and Co in sphalerite and marcasite.

Jan 1, 1981

F. G. CLAPP, New York, N. Y. (written discussion *).-Whatever processes of appraisal have been found most correct and feasible in one field or group of fields will generally prove most adaptable in others. So far as the California fields are concerned, Mr. Requa's paper appears to outline the most up-to-date processes of appraisal. It remains, then, to discuss and adapt these and to make such revisions in methods and processes of calculation as will give us results elsewhere. The trouble about most attempts to place a value on oil lands, whether in this country or elsewhere, has been that many of the so-called "experts" called upon to express an opinion either have not possessed the requisite engineering and geological knowledge to make an accurate appraisal of the lands, or that they were not furnished with sufficient information for the purpose in hand. The Independent. 011. Producers' Agency of California, for whom Mr. Requa's original report was prepared, had many advantages in this respect not generally available to engineers making reports, as all existing information seems to have been at the experts' disposal within the limits of a large number of properties, practically commensurate with the extent of the fields in question. Hence the report could be and was more accurate than any similar report for a single company is likely to be in other fields. Very few companies are so exempt from competition that all the data on neighboring leases of other companies will be freely turned over to them. In many companies, certain available data are concealed from the engineer who makes the reports, particularly if the properties are supposed to be worth less than their apparent value. In the case of other companies, having the best of intentions, the data are insufficient to help the engineer greatly in his appraisal, simply because the oil business has been so, unsystematic in most fields that only the largest and wisest companies have kept accurate figures regarding runs and gravity of oil from individual wells and from different depths. In many wells, which ran wild for clays or weeks in the older fields, there was a waste which is not recordable with exactness. These and many other difficulties confront even the most experienced expert in actual practice outside of the California fields. We may justly say, therefore, that an engineer in other fields of the United States and in the European, South American and Asiatic fields, must not only begin where the Independent Oil Producers' Agency

Jan 4, 1918

By A. S. Michaels, M. C. Porter, A. Stancell

Previous laboratory studies have demonstrated that the injection of small quantities of reverse wetting agents during water displacement can increase oil recovery from unconsolidated porous media.9 In the present investigation, an attempt has been made to determine more fully the effects of reverse wetting treatments and to clarify the mechanism by which increased oil recovery is effected. Water-oil displacements were performed in beds of 140-200 mesh silica sand. Hexylamine slugs (injected after 0.25 pore volume of water throughput), when adequate in size and concentration, were effective in promoting additional oil recovery. Their effectiveness increased with the quantity of amine injected. However, slugs of sufficient size and concentration to stimulate oil production at water flow rates of 34 ft/day did not do so at 4 ft/day. Visual studies in a glass grid micromodel have shown that the stimulation of oil production, via ayueous hexylamine, is a result of transient changes in the oil wettability of the pore walls. if the amine slug is of sufficient size and concentration to induce significant changes in the adhesion-tension, large continuous oil masses will be formed. if the superficial water velocity is high enough to result in rapid desorption of the amine, a favorable "wettobility gradient" may be established across the masses; under such conditions, high oil mobility is observed, and increased oil recovery results. INTRODUCTION It is generally agreed that the efficiency of oil displacement by water in porous media is limited in part by capillary forces which cause the retention of isolated masses of oil — resulting in the so-called "irreducible minimum oil saturation". Recent estimates10 indicate that there are about 220 billion bbl of petroleum in United States reservoirs which are not economically recoverable with present techniques (such as water flooding). This amounts to almost five times the known recoverable reserves. It has been recognized for some time that a suitable alteration in the water-oil interfacial tension and/or the contact angle, as measured between the water-oil interface and the solid surface, should result in better displacement efficiency. Surface active agents can be used as interfacial tension depressants to accomplish this objective,1,2,7 but unfortunately, the additional oil recovery is seldom commensurate with the treatment cost. In contrast to interfacial tension depressants, the effect of contact angle alterations on water-oil displacements has received relatively little attention in the literature. It is known that the wettability affects the displacement process.3,4,11 Displacements in water-wet systems generally result in lower residual oil saturations than those in oil-wet systems. The effect of "'transient" wettability alterations concurrent with the displacement process have been investigated by Wagner, Leach and coworkers,4,11 wherein it has been demonstrated that the establishment of water-wet conditions during water flooding of oil-wet, oil-saturated porous media is accompanied by significant increase in oil displacement efficiency. Michaels and Timminss studied the effects of transient contact angle alterations resulting from chromatographic transport of reverse wetting agents through unconsolidated sand. It was demonstrated that chromatographic transport of short-chain (C4 through C8) primary aliphatic amines can improve oil recovery and that the recovery increases with the quantity of amine injected (i.e., with either the amine concentration or the volume of the slug injected). Circumstantial evidence indicated that the increased displacement efficiency resulted primarily from transient changes in wettability of the porous medium. In the Present investigation. additional information has been obtained on the effects of reverse wetting treatments and the mechanism by which increased oil recovery is accomplished. Hexylamine slugs of varying size and concentration were chromato-

Jan 1, 1965

By A. E. Harnsberger

I is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practically every refinery operation, from the charging of crude oil to a distillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from — 50" F. to 900" F. Pressure may vary from subatmospheric to 2000 1b. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of —50" F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200" to 900" F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250" F. The second type of corrosion occurs in high-temperature pumping equipment, with temperatures from 450" to 900" F., largely caused by sulfur compounds. There are also other corrosive conditions met with in refinery operations, particularly in the handling of acids, acid sludges and other specialized processes. These problems, although difficult to

Jan 1, 1935

By A. E. Harnsberger

I is obvious that details such as the physical and chemical properties and methods of heat-treating of the materials mentioned must be omitted in a paper on the subject of materials used in oil-refinery pumps1. Only sufficient identification is given to enable the reader to find additional information from already published data. Also, the subject covers many operating conditions, but only the most important services can be discussed here. To the oil refiner, the pumping equipment is of vital interest. Practically every refinery operation, from the charging of crude oil to a distillation unit to the shipping of refined products, involves some form of pumping machinery. Intermediate refining stages involve a great variety of pumping machinery to carry out successfully the aims of the refinery technologist. Temperatures at which oils are handled vary from — 50" F. to 900" F. Pressure may vary from subatmospheric to 2000 1b. per sq. inch. The selection of the proper materials involves a careful consideration of the conditions under which the particular pump must operate. The four most important considerations are temperature, pressure, corrosion, and abrasion or wear. Consideration of temperature may be divided into three parts: (1) extremely low temperatures of the order of —50" F.; (2) temperatures at atmospheric or slightly above; (3) temperatures from 200" to 900" F. Pressures fall into two groups: (1) pressures reached by ordinary trade pumps of the order of 200 lb. per sq. in., (2) extreme pressure conditions involving pressures as high as 2000 lb. Noncorrosive and corrosive oils can be treated differently. Under the latter falls corrosion in the presence of water, which will occur up to 250" F. The second type of corrosion occurs in high-temperature pumping equipment, with temperatures from 450" to 900" F., largely caused by sulfur compounds. There are also other corrosive conditions met with in refinery operations, particularly in the handling of acids, acid sludges and other specialized processes. These problems, although difficult to

Jan 1, 1935

By Bruce T. Stanley

A key point in the design and operation of a modern mining operation is the construction of what is called an ore-body model or block model. This model is a representation of reality constructed from predicted information. The blocks involved are merely subsets of the overall model which allows manipulation of the contained information on a local scale. In general, block models enable mine planners to effectively select the most promising means of extracting the ore both physically and economically. The uses of a block model can be quite diversified, but one must realize that a single model that satisfies all curiosities and forms of expertise is difficult to construct.

Jan 1, 1979

By Immo H. Redeker

Abstract-North Carolina is the leading state in the US in lithium mineral production. Spodumene is mined in open Pits and concentrated by flotation by the two companies, Lithium Corp. of America and Foote Mineral Co. North Carolina State University has a mineral research laboratory in Asheville, N. C., with trained personnel, batch and pilot plant facilities to assist in the state's mineral development. The NCSU Minerals Research Laboratory assisted both lithium-producing companies with spodumene concentration problems and has lately worked closely with Lithium Corp. of America to develop the best flowsheet for spodumene and byproduct recovery. The concentration of North Carolina spodumene and byproducts from pegmatites is presented and illustrated with figures.

Jan 4, 1979

By Immo H. Redeker

North Carolina is the leading state in the US in lithium mineral production. Spodumene is mined in open pits and concentrated by flotation by the two companies, Lithium Corp. of America and Foote Mineral Co. North Carolina State University has a mineral research laboratoy in Asheville, N. C., with trained personnel, batch and pilot plant facilities to assist in the state's mineral development. The NCSU Minerals Research Laboratory assisted both lithium-producing companies with spodumene concentration problems and has lately worked closely with Lithium Corp. of America to develop the best flowsheet for spodumene and byproduct recovery. The concentration of North Carolina spodumene and byproducts from pegmatites is presented and illustrated with figures.

Jan 1, 1980

By Arthur F. Taggart

The quality of aggregate materials is. of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 1, 1950

By Hannu Penttila, Harrison R. Cooper, Olli Mattila

Two approaches to automated operation in metallurgical processes involve the conventional analog control or, more recently, digital control. The expanding use of digital controls applied to process automation is a comparatively new development. Several current technical reports describe digital control systems in concentrator grinding control, 1, 2, flotation, 3 and smelter operations. 4,5 The principle factors influencing trends to digital control are:

Jan 10, 1976

By Edward B. Walker, Michel Grosmangin

The geological and economic conditions peculiar to the Greater Oficina area are presented to demonstrate the necessity of a low-cost, well-site method of distinguishing gas-bearing formations. The method of gas detection with the neutron log is briefly discussed and its limitations are explained. A new method is described which consists in running a second neutron log with a larger source-to-detector spacing. Field data indicate that under favorable conditions the larger spacing response is proportionately more influenced by the virgin gas zone than is the shorter spacing response. One important condition is that the gas sands be invaded, with a diameter of invasion equal to about two to three times the hole diameter. The calibration of the longer spacing log is made so that the two logs read the same deflection in shale and in a known water or oil sand. Under such conditions, gas is indicated by a positive separation, i.e., the curve for the longer device is displaced to the right of the curve for the shorter device. Because of the non-linearity of the long spacing response, low porosity formations also show positive separations. In sands with large porosity variations, the gas sands can no longer he located visually. They can be detected on a plot of shorter spacing vs longer spac-ing deflections. INTRODUCTION In the Greater Oficina area of Eastern Venezuela, the rapid and accurate detection of gas from well logs is of primary importance because of a combination of economic, geologic, and operational conditions. Briefly, these conditions are: economic—there is no market for gas at the present time; geologic—a single well may contain as many as 30 or more oil or gas sands for which intervals -to be tested must be selected; opera-tional—first, once opened to the casing through perforations, gas sands are extremely difficult and expensive to squeeze off, and second, gas detection must be rapid because the geologist must decide immediately, at the well, which sand to perforate. During the early period of exploitation in Greater Ofi-cina, when clay base muds were used, sidewall samples, together with electric logs, gave fairly good distinction between oil and gas sands. When exploitation became concentrated on deep fields of poorer sidewall sample recovery, and after the advent of oil emulsion muds, now the standard drilling fluid in Greater Oficina, the regular neutron log became the most reliable indicator of gas. In 1953, R. Norelius devised the dual-spacing neutron technique for gas detection. The dual-spacing neutron log has proved to be highly successful in detecting gas and has been adopted as a regular survey by all of the oil companies of the area. Several hundred dual-spacing neutron logs have been run in Eastern Venezuela and several tests per well are available for positive evaluation of the logs. The findings outlined below are based upon this extensive field experience. GEOLOGICAL CONDITIONS OF THE GREATER OFICINA AREA The Greater Oficina area lies on the south flank of the Eastern Venezuela Basin (Fig. 1). Nearly all accumulations of oil and gas in the area are trapped, in whole or in part, against normal faults. All known oil and gas reservoirs in Greater Oficina occur in the Ofi-cina formation (Miocene-Oligocene) or in the "U" sands. The U sands are the lithologic equivalent of the Merecure group (Otigocene-Eocene), which contains oil in many fields north of Greater Oficina. Most of the petroleum produced in Eastern Venezuela is from the Oficina formation.

Jan 1, 1958

By M. Gangal, B. Paul

It may be seen from Maurer's survey (Maurer,l 1966) that most of the common methods used in rock drilling today depend upon mechanical loading of the rock. In order to predict the behavior of rock under an imposed system of stresses, it is necessary to have a valid criterion which delineates those combinations of stress which cause macroscopic rock failure from those which do not. Admittedly, the conditions under which brittle materials fracture depend very much upon statistically variable local effects such as inclusions, grain boundaries, minute imperfections, etc. However, it is extremely desirable to be able to predict fracture under complex states of stress by means of a stress-criterion of failure, where, for a given material, the effects of the other variables mentioned are incorporated into a small number of experimentally observable parameters. One of the most successful of these "macroscopic stress criteria" has been the Coulomb-Mohr theory 2,3 (also see Jaeger 4 and Terzaghi 5), modified by the addition of tension cutoffs (Paul 6). At first thought it might seem rather odd that a macroscopic theory is capable of predicting fractures which originate at highly localized random imperfections at an atomic level (or more likely at the level of individual mineral grains in rocks). However, Griffith7 showed that fractures originating near the tips of randomly oriented elliptical cracks lead to the macroscopic stress criterion of failure indicated in Fig. 1 (a). Fig. I (a) is to be interpreted in the following way: P and Q represent the maxi mum and minimum principal stresses (compression is considered positive) in a macroscopically isotropic body; fracture will not occur for any combination of principal stresses lying within the 'fracture curve' shown, but

Jan 1, 1967

By Lucien Eaton

INCREASED mining activity during the past year has brought to light changes in mining practice and advances in technique, born and incubated in the period of depression from which the mining industry is now emerging. Although the tendency toward large output from individual mines has continued, a salutary trend is evident toward greater efficiency at small mines, in which the gold mines of Canada have led the way. Improvement in excavating machinery and washing plants for small placers has continued, and knowledge of the possibilities and limitations of this kind of equipment has increased. Greater portability through sectionalization has been the keynote. Power, shovels and draglines mounted on caterpillar treads move from one deposit to another under their own power, and floating washing plants mounted on pontoons can be taken down, moved, and set up again by a small crew of men in only a few days.

Jan 1, 1937

By Nathaniel Arbiter, Chas. H. Behre

Two outstanding factors characterize most undertakings in the mineral industries: (1) mineral deposits are not equally distributed over the earth but are localized by natural processes, and (2) the mineral industries are largely based upon wasting assets. Neither of these factors is invariably true, for a few mineral materials, such as water, are essentially world-wide and others are replaced periodically by processes not unlike crop production. Indeed, with some, such as the salts in the sea, the supply is cyclic in short or long periods, whereas others, like water, though locally or periodically in short supply, are essentially inexhaustible. But to the extent that most minerals are limited to certain areas and are "permanently" consumed, any industry founded upon them, by implication, demands great care in planning for the most effective extraction-the essence of wise and conservative expenditure. Several less unusual yet also truly fundamental factors in the economics of the mineral industry are those involving (1) the various kinds and properties of mineral materials, which influence their use; (2) their geologic and geographic availability; and (3) the 'techniques unique to their discovery, exploration, and utilization. This chapter is designed primarily as a brief background for later ones and as a summary of the several unusual or at least special factors and of their effect upon the economics of the mineral industry. The social and political and especially the economic aspects of the industry are the main subjects of this volume and are dealt with in extended fashion in subsequent chapters. Fundamental Characteristics of Mineral Deposits DEFINITIONS Minerals are naturally occurring compounds of nonliving matter, each technically defined as having ( 1 ) a chemical composition that may vary

Jan 1, 1964

By Joseph A. Holmes

Although Venezuelan production attained a new peak in 1938, passing the 190 million barrel mark for the first time, there was a distinct flattening of the steep upward trend that marked 1937 and preceding years. The annual total of 190,231,780 bbl. was only 31/3 million barrels above the 1937 figure, an increase of slightly less than 2 per cent, which contrasts sharply with the 20 per cent increase of 1937 over 1936. As in the previous year, the Lake Maracaibo fields supplied approximately 73 per cent of the oil produced, Lagunillas remaining the largest single contributor in spite of a 17 million barrel decrease in its annual output. Tia Juana increased its percentage of the Venezuelan total from 14.1 per cent in 1937 to 23.4 per cent in 1938; La Rosa showed little change with 13.7 per cent; Quiriquire in eastern Venezuela was also little changed with 13.2 per cent; Mene Grande, the only other field of real importance, declined from 7.7 per cent of the total in 1937 to 6.6 per cent for 1938. Two new fields, Temblador and Bachaquero, began actively to ship oil during the year, and by November were averaging 7600 and 10,000 bbl. per day, respectively. The former is in eastern Venezuela, and the latter is the most southern of the proven Lake Maracaibo fields. (A map of Venezuela was published in Volume 127 of the Transactions.) Table 1 gives a complete résumé of Venezuelan production by fields for 1937 and 1938, and shows that 1,685,575,663 bbl. had been produced to Dec. 31, 1938. The percentage contributed by each of the principal fields to this total is shown in Table 3, as well as their trends over the past several years. From these data it is apparent that the Maracaibo Basin is the principal source of Venezuelan production, and will probably continue to hold this position for some years. At the year's end 2657 oil wells were producing, of which 2425 were in western and 232 in eastern Venezuela; 36 per cent were on natural flow, 57 ppr cent were pumping, and 7 per cent were on air or gas lift. Out of 523 wells drilled, 507 producers were completed in 1938, five less than in the previous year and nearly 100 less than in 1929. These

Jan 1, 1939