Search Documents

By E. A. Anderson

IN another paper1 the writer has shown that the low permissible maximum fiber stress in a loaded zinc sheet demands a much closer support spacing than is used for steel. The limiting fiber stress in 13-gage (0.032 in.) sheets having a 1-in. depth of corrugation was found to be about 5000 lb. per sq. in. on a 37-in. span under a load of 40 lb. per sq. ft. Corrugated steel sheets are commonly laid with spans varying from 48 to 60 in. In order to increase the span in 13-gage zinc to 54 in. (a common spacing) the metal must be capable of withstanding, under long-continued loading, a maximum fiber stress of about 10,000 lb. per sq. in. This is known to be impossible with unalloyed zinc. In this paper the writer describes a series of experiments leading up to the development of an alloy capable of safely sustaining this fiber stress. The effect of alloying on the slow creep of zinc was studied by means of static tensile tests, accurate determinations of apparent elastic limits and finally by means of loading tests on full-size roof sections. Two industrial buildings roofed with alloyed zinc sheets on spans involving fiber stresses in excess of 10,000 lb. per sq. in. have been under observation for over two years without signs of sagging.

Jan 1, 1929

By AIME AIME

CHARLIE WARNER, Chairman of the Petroleum Division, is no stranger to the problems of the oil industry or to those of the Petroleum Division, after more than 25 years of experience in locating and producing oil and more than 22 years of membership in the Institute. He was born at Jefferson, N. Y.. April 27, 1894, and educated in the public schools of New York State and at Cornell University where he studied geology and allied sciences from 1913 to 1917 and received a B.A. degree. Immediately upon completion of this training, he was employed by the Empire Gas & Fuel Co. as a field geologist in Oklahoma and Kansas. Two years later he became district geologist for the Emerald Oil Co. in Oklahoma and Kansas, and in 1920 he rejoined the Empire Gas & Fuel Co. in the capacity of district geologist in Oklahoma. In September of 1921 he began his association with the Houston Oil Co. of Texas. He was district manager for the company in the Mid-Continent area until 1932 when he was transferred to the head office at Houston, where he became superintendent of the land and lease department in 1934 and was elected a director of the company in 1941. In these capacities, and also as petroleum engineer for the company, he keeps in intimate touch with all phases of field activity and with the regulation of the industry by State and Federal agencies.

Jan 1, 1943

By W. F. Boericke

THE recent completion by the United States Aluminum Company of a $4,000,000 addition to its plant at Massena, N. Y., consisting of a large blooming mill and structural mill, gives this organization, a subsidiary of the Aluminum Company of America, the distinction of possessing the largest aluminum rolling mill in the world, as well as the first mil1 in this country to roll aluminum exclusively. The plant is located near the international boundary line between Canada and the United States, about 3 miles from the St. Lawrence River, to take advantage of the development of cheap hydroelectric power which is needed not only for the manufacture of structural shapes from the ingots, but in the reduction of alumina to the metal by the well-known Hall process as well. A power canal from the St. Lawrence River to the power house on the Grasse River at the plant provides for the waterflow, which, coupled with a drop of 47 ft. in 2% miles, generates 80,000 hp. through vertical turbines. An additional 60,000 hp. is purchased.

Jan 1, 1930

By H. A. Schwartz

From time to time, one of the authors has had occasion to investigate the graphitizing reaction and has published the results mainly as discussion' of the work of other investigators. In view, therefore, of the diversity of both observations and interpretation, it seemed well to attempt, a revision of the entire subject in the Research Laboratory of the National Malleable Castings Co. The work consisted of a careful study of a single, impure, iron-carbon alloy. The material, which may be considered typical low-carbon white cast iron of the malleable industry, was an air-furnace iron of the following composit,ion: carbon 2.30 per cent., silicon 1.20 per cent., manganese 0.29 per cent., phosphorus 0.156 per cent., sulfur 0.048 per cent. The freezing range extended from 1213' to 1132' C., the latter figure agreeing with Gontermann's data.2 We have attempted to define the equilibrium diagram of this alloy, in the stable condition as related to the mctastable diagr,aui,- from a temperature somewhat below the euteetic freezing point to a temperature l>clow Arl and for a graphitic-carbon content from practically notliing to the original total rarbon of the specimen (see Fig. 6). More csp~c~ially we desired to locate the line in the stable diagra~n corrcspo~idi~lg to thc Ac, line of the metastable syst,ern, which is designated by analogy, thc At, line (t, from tcrnpcr carbon); also to dctermirle the locat'ion of A tm witah respect, to Acm t,o~vard their lowcr extremities at Arl in ordei to determine whether or not graphitization is completed by th~ separation of an iron-carbon entectoid analogous to pearlite in the iron-cementite system. This would involvc furthcr a colnparison of thc locations of Ihc stablc and met.astable 41 points. As the carbon concelltrations of thc solid solutions of the two syste~~ls are probably not, identical, an explanation of t>lieir differences and of thc,

Jan 1, 1923

By Herbert Clark Hoover, Lou Henry Hoover

PREVIOUSLY I have given much information concerning the miners, also I have discussed the choice of localities for mining, for washing sands, and for evaporating waters; further, I described the method of searching for veins. With such matters I was occupied in the second book; now I come to the third book, which is about veins and stringers, and the seams in the rocks1. The term "vein" is sometimes used to indicate canales in the earth, but very often elsewhere by this name I have described that which may be put in vessels2; I now attach a second significance to these words, for by them I mean to designate any mineral substances which the earth keeps hidden within her own deep receptacles.

Jan 1, 1950

By N. T. Cotman, C. H. Pickering, P. B. Crawford

A beat-conduction model has been developed to study the flow of fluids in a stratified oil reservoir which is being subjected to unsteady-state depletion. To simulate stratification, plates of different metals were joined together so that cross flow could occur between strata. A description of the model, plate construction and necessary instruments is included. The data indicate that stratified oil reservoirs experiencing cross flow may be treated as a single, homogeneous, producing sand having properties intermediate between those of the layers making up the system. A technique for averaging core-analysis data to arrive at the proper average value of rock permeability and porosity is presented INTRODUCTION Although oil has been produced from reservoirs for 100 years and reservoir injection processes have been undertaken for 40 years, the industry is still inadequately informed on the problem of reservoir inhomogeneities. Stratification is perhaps the best-known type of reservoir heterogeneity. Urenl discussed the possible significance of this nonuniformity in his 1927 paper on the theoretical aspects of water flooding. Since this time the problem of vertical permeability variations has been the subject of much discussion and numerous papers. Levorsen2 simply describes the origin of layered beds in his Geology of Petroleum. Some beds are field-wide and may be traced from well to well, while others apparently pinch-out and become discontinuous. In addition, the physical characteristics of a layer may vary from place to place. For these reasons, a stratified system is not easily defined. In calculations involving oil reservoirs in which permeabi1ities vary, methods presently used contain many simplifying assumptions. The reservoir frequently is considered as consisting of permeable layers, each of uniform vertical and lateral permeability and each behaving as if separated from adjacent layers by thin impermeable layers. Other assumptions frequently made in reservoir calculations are steady-state flow conditions, unit mobility ratio, linear geometry, average or homogeneous porosity, and negligible capillary-pressure and gravity effects. Muskat3 has. developed solutions to the stratification problem for mobility ratios other than unity for both linear and exponential permeability distributions. He assumes lateral uniformity and continuity of all productive strata and does not consider porosity. This study will take into account transient effects, cross flow and varying porosity, as well as the variations in permeability, by means of a heat analogy. Muskat5 has shown the similarity of the equations which describe the flow of fluids in a porous medium to the flow of heat through a solid. Landrum, et al,6 made an analogy between the flow of fluid in an unsymmetrical reservoir and the conduction of heat in a similarly shaped metal plate. This analogy is summarized briefly as follows. If fluid is produced from an oil reservoir above the bubble point, the resulting pressure distribution will be identical to the temperature which would result in a metal or heat-conducting plate if heat were similarly removed. This means that a study of heat flow in stratified thermal models will behave like fluid flow in stratified oil reservoirs. For mathematical correspondencies, set- Ref. 6. The fluid mobility k/p is proportional to the thermal conductivity, and the porosity-times-compressibility product is proportional to the density times specific heat of the thermal plate. EXPERIMENTAL EQUIPMENT AND PROCEDURE The stratified reservoir model used in this study is illustrated schematically in Fig. 1. A Leeds and Northrup Speedomax Type G temperature recorder

By J. A. Holmes

Venezuela has continued during 1929 to demonstrate that it is destined for many years to come to be one of our most important sources of crude petroleum. The producing fields of the Bolivar Coastal district along the east side of Lake Maracaibo have continued their phenomenal production, and two new fields have reached the near producing stage, while the results of deep test wells have strengthened the predictions and expectations that oil will be found and produced from many other pools and from several different geological formations. The finding of these new oil pools is not going to be easy, because the surface evidences of geological structure are scanty, and the subsurface problems are difficult, but intelligent effort backed by ample resources may be counted upon to overcome these obstacles and lead to a continued increase in the number of producing fields in Venezuela. During 1929 the total production of Venezuela was approximately 135,953,000 bbl., an increase of nearly 30,000,000 bbl., or 28 per cent., as compared with the preceding year. During 1929 oil in steel storage in Venezuela decreased from 13,000,000 to about 11,000,000 barrels. Tables 1, 2 and 3 briefly summarize Venezuelan production by fields and by years, and show the trend of production since its establishment on a commercial basis. Table 1.---Production of Crude Oil in Venezuela by Years, 1917 to 1929 All Figures in Barrels of 42 Gallons Total PRodUction Total PRoduction Year VeneZUela, Bbl. Year Venezuela, Bbl. 1917....................... 227,000 1927.................... 63,181,000 1918....................... 368,000 1928.................... 106,000,000 1919....................... 258,000 1929.................... 135,953,000* 1920..................... 548,000 Grand Total Since Ineep- 1921...................... 1,544,000 tion................... 380,791,000 1922....................... 2,448,000 Increase, 1929 over 1928.. . 29,953,000 1923..................... 4,170,000 Per cent. Increase......... 28.2 1924....................... 9,234,000 Per cent. 1929 Production 1925....................... 20,219,000 of Total............... 35.7 1926....................... 36,641,000 * Includes estimate for closing period of 1929.

Jan 1, 1930

By J. B. Newkirk

IN 1939 Bitter and Kaufmann1 suggested that iron, precipitating from a copper-rich, Cu-Fe solid solution, appears initially as coherent particles of r-Fe which transform to the body-centered-cubic form of iron when the alloy is cold worked. Since then there has been considerable discussion, supported only by indirect evidence, regarding the validity of the concept. For example, Reekie, Hutchison, and Hether-ington2 interpreted the changes in electrical resistance accompanying the aging of Cu-Fe specimens in terms of a coherent 7-Fe precipitate which transformed to the incoherent a-phase during long aging or cold working. Greninger- ound that Cu-Fe alloys which had been water quenched from 1050" and then held at 650°C for 3 hr changed from weakly to strongly ferromagnetic as the aged wire was subsequently cold worked. He also found diffraction lines corresponding to body-centered-cubic iron in Debye-Scherrer patterns given by aged and worked specimens but lines corresponding to only one face-centered-cubic phase in specimens which had been aged but not worked. Knoppwost,' and later Cech and Turnbull,5 found that aged Cu-Fe specimens showed a slight increase in ferromagnet-ism after they had be? cooled in liquid nitrogen. Very recently Denney6 followed the kinetics of the precipitation reaction as indicated by the saturation magnetization, hardness, and diffuse X-ray effects. The experimental results reported by all of the authors mentioned above are readily explained in terms of the Bitter and Kaufmann concept. However, most of the evidence is indirect when used to define the structural changes involved. It was the aim of the present investigation to determine the mechanism of precipitation of iron from a Cu-Fe solid solution in the light of available published information and with additional new and more direct experimental data. Experimental Method At 1060°C copper will contain up to 3 atomic pct Fe in equilibrium solid solution.7 The solvus slopes rapidly toward lower iron concentration, so that at 600°C only about 0.5 pct Fe remains in solution at equilibrium. Below the eutectoid temperature (850°C), the iron-rich phase in equilibrium with the copper-rich solid solution consists of body-centered-cubic a-Fe. Above 850 °C the equilibrium iron-rich phase is face-centered-cubic r-Fe. The alloy to be studied was made by melting electrolytic iron and OFHC copper by induction under vacuum in an Alundum-lined crucible. The metal was held molten for about 5 min, after which time the power was turned off and the crucible was tipped about 70" to promote directional solidification. The resulting ingot, containing 2.5 wt pct Fe by analysis, was clean, large grained, and free of gross segregation. Slices % in. thick were cut from the ingot, rolled to 1/8 in. in thickness, homogenized in hydrogen at 1060°C for 24 hr and, finally, quenched in cold water. Specimens for all subsequent tests were made from these slices. Squares measuring about 1 cm on a side were cut from the slices to make specimens for studying hardness and microstructure. Wires (0.020 in.) for the Debye-Scherrer survey were drawn from 1/8 in. sq rods which had been cut from the homogenized slices. Large crystals for observing diffuse X-ray diffraction effects were prepared by mechanically

Jan 1, 1958

By G. F. Sager, B. J. Nelson

Magnesium alloy forgings offer higher and more uniform mechanical properties than heat treated magnesium alloy castings and are used principally for light weight parts that may be stressed in fatigue or subject to impact loads, or where space limitations do not permit the use of the necessarily bulkier magnesium alloy castings. Compositions and Properties of Magnesium Forging Alloys The nominal compositions and properties of the principal commercial magnesium forging alloys are given in Table 1. The two that are most commonly used are AMC58S and AM65S. The former has the highest strength and is, therefore, employed for heavy duty applications. However, the forging of this alloy and of AMC57S ordinarily requires the use of slow speed hydraulic presses. The forging alloy AM65S combines good, although somewhat lower, mechanical properties with excellent forging characteristics. This alloy can be forged on hammers, upsetters, rolls, and mechanical presses, as well as on hydraulic presses. These characteristics make it particularly useful for many applications. Manganese Segregation in AM65S The alloy AM65S contains 5 pct tin, 3 1/2 pct aluminum, and a small amount of manganese, the manganese being added to insure satisfactory resistance to corrosion. Some manganese segregation was occasionally encountered in this alloy. In many applications, such segregation is of no particular consequence, but when forgings are acid dipped prior to the application of various chemical coatings, the segregated particles of manganese constituent may stand in relief. The resultant surface roughening may impair appearance and is undesirable in forgings employed in the textile industry, where very smooth surfaces are essential to avoid the catching and breaking of fine threads. An effort was therefore made to determine the cause of manganese segregation in this alloy and find a method for its elimination. Radiographic examination of a series of cast ingot sections and extruded samples of the AM65S type having manganese contents ranging from zero to about 0.7 pct revealed no appreciable manganese segregation when the manganese was less than about 0.4 pct. A small amount was observed with a manganese content of 0.46 pct and considerable with manganese contents of 0.6 pct or higher. Attempts to eliminate the manganese segregation by variations in the melting and casting conditions were unsuccessful and it soon became apparent that the trouble was attributable to the fact that the manganese contents that caused segregation were in excess of the amounts that would remain in solution at temperatures encountered in the melting and/or casting operations prior to the complete solidification of the ingots. A knowledge of the amounts of manganese that would be soluble in molten alloys of the AM65S type at various temperatures was obviously desirable. The liquid solubilities of manganese in binary Mg-Mn alloys and in Mg-Al-Mn and Mg-Zn-Mn alloys have been determined by Tiner and others,* but no data on the solubility of manganese in molten magnesium alloys containing tin and aluminum are given in the literature. For this reason, an investigation to determine the solubility of manganese in a magnesium alloy containing 5 pct tin and 3.5 pct aluminum (AM65S type) was undertaken.

Jan 1, 1950

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917

By R. S. Hadi, L. Svarovsky

SUMMARY This is a report of a new development in on-line particle size measurement of fine powders in dust-laden gases. A continuous sample of the solids-air suspension is drawn from the process stream via a sampling probe by means of an air operated ejector into a cyclonic separator whereby the sample is subjected to a particle size dependent separation process and split into two streams, "overflow" and "underflow". The overflow stream carries most of the fines at a relatively low concentration and the underflow stream carries the coarse particles at a relatively higher concentration. The concentration of solids in the two streams is detected by electrostatic noise level technique which utilises the electrostatic charge accumulated on the solid particles due to their high velocity in the turbulent air stream, for the mass concentration measurement. The ratio of the solids concentration of the fines stream to that of the coarse stream is then correlated against the average particle size in the main process stream by a calibration curve. The in-plant tests clearly indicate that this relatively simple instrument offers good sensitivity in the size range from 2 to 6 µm, and is capable of giving a continuous indication of average particle size for process control purposes. Although the instrument was developed for a particular application, it may be used in other situations where fine powders are conveyed in gas streams. British and foreign patents are applied for.

Jan 1, 1980

By D. L. Albright, R. W. Kraft, J. A. Ford

HE unidirectional solidification of A1-CuAl, eutec-tic specimens to produce an essentially parallel lamellar structure has been described previously.' Ingots solidified in this manner ordinarily exhibit three macroscopic zones. In Zone I, at the head end of the ingot, a large number of slightly elongated grains occur in which the lamellae are highly distorted and twisted. After a few centimeters of growth, this distribution gradually changes to a small number of coarse grains elongated in the growth direction and in which the lamellae are quite regular, Zone 11. Zone 111, at the tail end of the ingot,

Jan 1, 1963

By Ben-Zion Weiss, Melvin R. Meyerson

FATIGUE crack propagation in some aspects can be viewed as being a result of localized plastic deformation concentrated near the tip of the crack.' Deformation is influenced by microstructure which in turn can affect the fatigue crack growth significantly. To study the effect of localized microstructural changes on fatigue crack propagation, cantilever-type notched specimens were subjected to cyclic bending at constant load amplitude. The extent of fatigue crack propagation was obtained by measuring the length of the crack by periodic observation with a microscope on the polished side of the sample,2"4 and these data were used in preparing the curves in the figures which follow. Figs. 1 (solid lines) and 2 show experimental results obtained in austenitic type 302 stainless steel containing higher than standard carbon (0.24 pct C) and 310 stainless steel. Both steels were homogenized for 8 hr at 1120°C and then water-quenched in order to prevent the precipitation of carbides. Fig. 3 shows experimental results obtained on 9440 low alloy steel in the normalized condition and in the quenched and tempered (580°C) condition. Indications of microstructural influence can be seen in scattering of the experimental data. The degree of scattering depends on both the microstructure and the amount of cyclic stress applied to the sample. For microstructures which are more easily deformed plastically, e.g., normalized or annealed as compared with hardened and tempered structures, the scattering is greater. Similarly, higher stresses produce greater scattering in the results, regardless of whether the cause of the stress increase is due to initial loading conditions or the growth in crack length. Scattering is believed to be a result of partial redistribution in the stress field around the tip caused by plastic deformation. This opinion is borne out by much smaller scattering of experimental results in the austenitic 302 high-carbon (0.24 pct C) steel. In this steel, plastic deformation in the neighborhood of the crack causes partial mar-tensitic transformation of metastable austenite,5 which in turn restrains further plastic deformation. As a result, the stress redistribution around The tip is reduced. Partial martensitic transformation was confirmed

Jan 1, 1969

By Bradley Stoughton

AT THE meeting of the Board of Directors on May 20, the resignation of Bradley Stoughton as Secretary of the Institute was presented and regretfully accepted by the Board. The letter of resignation follows : Gentlemen: About two years ago, I indicated to the President and some members of the Board my belief that the office of Secretary of the Institute should not be a permanent one. It is my observation of events, not only in our own Institute, but also in several sister societies, that too long a tenure of office by the Secretary inevitably leads to a situation which is not good either for him or for the society. After submitting this in writing to the Directors on February 17, 1920, I was overpersuaded by members of the Board to defer resignation until a more convenient time for the

Jan 1, 1921

By James T. B. Ives

The variety of copper-ore to which these notes refer is cornparatively rare, and, so far as I am aware, has not been recorded hitherto as occurring in Ontario. Moreover, the rocks of this locality differ so much in nature and mode of occurrence from the orebearing rocks of the western United States, that a description of them may be interesting. A line drawn upon a map of the region of the great lakes from the mouth of the Severn river at the Southern end of Georgian Bay, following the Canadian shore northwestward, and leaving Manitoulin island to the south, will describe the boundary between the Archaean rocks lying north of it and the Silurian rocks southward.

Jan 1, 1890

By Grover R. Castle

INTRODUCTION Banks are being asked to assume more and more of the project risk in connection with project financings and, as a result, they are seeking to become more sophisticated in the way that they approach these kinds of financings. For example, a large number of banks that are active with the mining companies have established mining groups which typically will include mining engineers, economists, and bankers, in order to specialize their service to the mining industry. These banks have geared up these special service staffs so that they will be better equipped in their lending activities to analyze, measure and evaluate the project risk. The hope is that a team of these specialists will be able to predict the potential success or failure of these new "green fields" mining ventures that the banks are asked to finance. This paper shall focus on this subject and try to determine just how successful these specialists can hope to become as they analyze these various projects that are brought to them for financing. The approach that shall be taken in this paper shall be to examine how successful the mining companies themselves have been in the past with this same problem. These mining companies should be the most sophisticated in their approach to the analysis of the potential for success of a new mine because they have had the most experience in evaluating these projects. After all, who knows more about developing a mine than the companies that have developed similar mines in the past? For the purposes of this paper, the writer has selected a sample of 18 mines that have been developed over the years and measured the actual performance of each of these sample ventures against the original projections. All of these cases have involved the development of large projects where the sponsors or partners in the venture are substantial and sophisticated companies and where the feasibility studies have been prepared by engineering firms that are considered very professional in the industry or alternatively where the feasibility has been done by a comparable in-house staff. The sample cases have been chosen from a period which starts in 1965 and continues through 1981 with the cases distributed over that period as indicated below: [ ] Fourteen of the projects are open pit mines, three are underground mines and one mine starts on the surface and gradually goes underground. Seven of the mines are in the the far east with the remaining three in either South or Central America. The following four specific questions were examined for each project:

Jan 1, 1985

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4010(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mobs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyro-phyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constitu-ents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 percent and the alumina from 22 to 33 percent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent.

Jan 1, 1940

By AIME AIME

PLANS are now well advanced for the joint meeting of the Institute and over a dozen other engineering societies in Chicago during the week beginning June 26: Engineers' Week at A Century of Progress. All engineers planning to visit the Fair will find it to their advantage to be present at this time so far as the Chicago attractions are concerned, and Eastern members will also have the advantage of special transportation arrangements on June 24 and 25. The tentative program is given at the bottom of the next page. Monday morning, June 26, will be reserved for registration of members and guests and the Woman's Auxiliary at the Stevens Hotel, where special rooms will be provided. A luncheon will also be served there, and in the afternoon, a technical session on nonmetallics. Instead of having the big family dinner that evening at the Stevens, as at first proposed, the local committee has planned to have it at the Fair Grounds, where special facilities have been arranged. A meeting of the Board of Directors and a few invited guests will precede the dinner. All members and guests are likely to be interested in visiting the Museum of Science and Industry, so that will be the sole event on the program for Tuesday morning, June 27. The big attraction there at present is the model coal mine, the first operative coal mine ever built for exhibit purposes. It is based on the Deutsches Museum mine at Munich, but goes far beyond that in realism, and takes the visitor on an extended tour underground. It shows him in half an hour more types of modern mining machinery and coal geology than he would be likely to see in a week's underground study in the coal fields. The Institute members will be the first group to go through this mine.

Jan 1, 1933

By R. A. Garling

INTRODUCTION Since the infancy of in situ uranium mining, a growing number of hydrometallurgical processes have been incorporated into pilot and commercial scale flowsheets. Although initial design efforts were geared toward maximizing uranium recovery and minimizing plant and wellfield flow circuit maintenance, recent emphasis has shifted to improved means of water conservation and aquifer restoration. As mining units approached depletion, evaporation ponds reached minimum freeboard, and state and federal agencies demanded proof of groundwater restoration, processes including mixed bed and conventional ion exchange, reverse osmosis and electrodialysis were adopted by the industry. These units served the additional function of reducing process bleed flows during mining in states where the deep disposal well permitting ice remains unbroken. This report concerns the use of electrodialysis as an alternative to the more conventional processes used in in situ mining. In addition to a brief history and description of the process, a comparison to reverse osmosis and operational data derived from testing an Ionics, Inc. 1.31 x 10-3 m /s (30,000 gallon/day) unit at the Teton-Nedco Leuenberger Research and Development pilot will be presented. HISTORY Commercially practicable electrodialysis was contingent upon the development of synthetic ion exchange membranes in 1940's. In 1952, Ionics Inc. demonstrated that the process was amenable to the treatment of salt and brackish water and, in 1954, made their first commercial sale. The following decade saw several major electrodialysis unit sales which were generally targeted for use on private or municipal potable water treatment. Major increases in membrane desalting unit capacities, facilitated by technological advances in the reserve osmosis industry, were noted during the 1970's. The development of polarity reversing electrodialysis equipment which reduced feed pretreatment requirements, increased water recovery rates, and simplified unit operation, kept Ionics Inc. competetive in the water treatment industry. Engineering advances which incorporated automated equipment, non-corrosive construction materials, and improved ion exchange membranes allowed the electrodialysis process to compete in industrial waste treatment among other commercial markets. PROCESS AND APPARATUS DESCRIPTION The electrodialysis process utilizes direct electrical current passed across a stack of alternating cation and anion selective membranes in order to achieve an electrochemical separation of ionized materials in an aqueous solution. The membrane stack has the appearance of a plate and frame filter press and auxilliary equipment includes solution pumps, electrically actuated valves, filters, piping and a direct current power source. The ion separation membranes are thin sheets of synthetic cation or anion selective resins. Attaching sulfonate or quaternary ammonium groups to the cross linked copolymer structure determines the ion selectivity of the membrane. The membranes are separated from each other in the stack by non-conductive spacers that house flow channels which route the flow tortuously and parallel to the membranes. Direct electrical current passing perpendicularly to the membranes and solution passages attracts cations toward the cathode and anions toward the anode (Figure 1). As the ions from the feed stream pass through the ion selective membranes, they become concentrated in the adjacent brine channel and are retained there by the combined attractive force of the electrode and the repelling force of the next membrane toward the electrode. Limiting factors on the degree of demineralization possible include chemical solubilities in the brine flow and the current density that will produce an unacceptable degree of polarization (Figure 1). Feed or brine solution treatment with complexing agents or acids has been successfully applied to prevent membrane scaling. Polarization can occur when sufficient current density is applied to dissociate water in the ion depleted region of the diluting compartments near the membrane surfaces. Significant polarization is evidenced by large electrical resistances across cell pairs and notable pH differences between diluting and concentrating streams. Limiting current densities have been increased in U.S. manufactured equipment by utilizing tortuous flow paths of relatively high linear velocities thereby promoting continous solution mixing. Energy consumption is due to separating electrolytes and solutions, oxidation and reduction reactions occurring in electrode compartments, overcoming electrical resistance, conversion from AC to DC power, solution pumping and auxiliary equipment actuation. A major improvement to the basic electrodialysis process was applied in 1970 which resulted in frequent, automatic cleaning and descaling of membrane surfaces. The process, polarity reversal, incorporates alternating the cathode and anode on a periodic basis while exchanging product and brine flow channels via electrically actuated values. The reversal reduces the potential of stack plugging with CaCO3 (calcite), CaSO4 (gypsum), and colloidal materials and, in most waters, eliminates feed pre-treatment requirements. For approximately two minutes during and following the reversal, off spec. water is flushed to waste or reintroduced to the feed supply. The usual feed treatment on polarity reversing electro-

Jan 1, 1982

By A. D. Zunkel, A. H. Larson

Equilibrium arsenic contents of Pb-As alloys in contact with PbO-As2O3 slags containing less than 30 mol pct As2O3, were determined at 650°, 700: and 750 C in an inert at?rzosphere. In this temperature range, the arsenic content of the alloy increased with increasing temperature in the single-phase liquid slag region and decreased with increasing temperature in the two-phase slag region and the single-phase solid-solution slag region. The PbO-As2O3 phase diagram below 22 mol pct As2O3 was determined by thertrzal analysis and by application of a log ?As2O3/?PbO vS log XAs2o3 /x3pbO plot determined from the equilibrium actiuity data. The resulting phase diagram was not well-defined since the eutectic temperature was not detected in the thermal analysis experiments, although a region of terminal solid solubility of As2O3 was found. Results from the phase diagram determination are compared with an existing diagram in the literature. THIS experimental investigation is an extension of a study by the authors1 on the slag-metal equilibria in the systems concerned with commercial lead refining processes such as softening and dross fuming. The first part of this investigation was a study of the slag-metal equilibria in the Pb-PbO-Sb2O3 system. The only experimental work previously done on the Pb-PbO-As2O3 system was by Pelzel2,3 in which the phase diagram for the PbO-As2O3 system was determined below 50 wt pct As2O3 and the equilibrium constant for the reaction 3Pb + As2O3 + 3PbO + 2As was determined as a function of temperature. No slag-metal equilibrium data have been determined. It is due to the scarcity of information regarding the Pb-PbO-As203 system that this work was undertaken. This paper describes the determination of the slag-metal equilibria in the Pb-PbO-As203 system by equilibrating Pb-As alloys with PbO-As2O3 slags in an inert atmosphere, the effect of 1 wt pct additions of bismuth and copper on the slag-metal equilibria, and the PbO-As2O3 phase diagram both by thermal analysis and the use of the slag-metal equilibria data. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade and assayed as follows: 1) 99.8 pct PbO (0.014 pct insoluble in CHJCOOH, 0.02 pct not precipitated by H2S, 0.1 pct CaO, and 0.08 pct SiO2); 2) 99.95 pct As2O3; 3) 99.99 pct Pb; 4) 99.0 pct As; 5) 99.99 pct Cu; and 6) 99.97 pct Bi. Room-temperature X-ray patterns revealed no detectable impurities in any of these materials. Apparatus for Equilibrium and Thermal-Analysis Determinations. The resistance-heated crucible furnace used in this investigation employed nichrome elements and was mounted so that it could be raised to surround the reaction tube during each experiment and, subsequently, lowered. A schematic diagram of the apparatus is shown in Fig. 1. Each charge was heated in a 3+-in.-OD by 31/2-in.-high 416 stainless-steel crucible placed in a 41/4-in.-1D by 18-in.-long fused-silica reaction tube which was closed at one end. On a shoulder around the crucible was placed a 3: -in.-OD by 12-in.-long open-end fused-silica condenser tube. The open end of the reaction tube was covered by a water-cooled brass cap with ports for 1) admitting an inert atmosphere to the system through a stopcock, 2) introducing a stainless-steel, motor-driven, paddle stirrer into the crucible, 3) evacuating the system with a mechanical vacuum pump, and 4) sampling the melt with Vycor sampling tubes. The brass cap was fitted to the open end of the reaction tube with a silicone gasket and collar clamp. The furnace temperature was controlled by a Barber-Coleman Capacitrol controller and a chromel-alumel thermocouple. Due to the corrosiveness of the melt, the controlling thermocouple also served as the measuring thermocouple. The temperature of the melt was calibrated against the controller temperature and was checked periodically during each test with a Vycor-enclosed calibrated chromel-alumel thermocouple. The temperature measurement and control can be considered accurate to ±3°C. Procedure. The charge placed in the crucible for each experiment consisted of 1000 g of Pb-As alloy and 300 g of PbO-As2O3 slag. The crucible was then placed in the reaction tube, the condenser tube was placed on the shoulder of the crucible, the silicone gasket and brass cap were fitted on the open end of the reaction tube, and the entire system was evacuated and filled with argon ten times. After the last flushing, a positive argon pressure of 1 psig was impressed on the system. The furnace was then raised to sur-

Jan 1, 1968