Search Documents

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

By John Nunes, Frank R. Larson

Temperature-dependent functions of various ten-sile flour stress and fracture parameters were investigated on iron and low composition alloys of Fe-C, Fe-Cr, Fe-Mn, and Fe-Ni. Data were obtained over a range of test temperatures from 200" to -196"C at an initial strain rate of 0.01 min". It was found that the strain-hardening exponent, n, for the Fe-Ni alloys increased significantly at very low testing temperatures with increased alloy addition. Also, the stress and strain at fracture followed a predictable transitional type of behavior. The flour stress-temperature dependence was evaluated employing the relation: M where it is shown that composition can strongly influence the constant M. An empirical formula describing this effect is as follows: M = MI (equivalent at. pct Ni)-'" Some preliminay, tests were run on several commercial steels to test the generality of this relationship. One of the phenomenological explanations of the ductile-to-brittle transition encountered in bcc metals is based upon the difference in the temperature dependence of the flow and fracture stresses.' It states simply that the fracture stress is relatively insensitive to temperature and that the yield or flow stress rises rapidly with decreasing temperature so that, when the flow stress reaches the fracture stress, brittle fracture occurs without appreciable plastic deformation. This behavior is illustrated schematically in Fig. 1 where the ductile-to-brittle transition is shown to occur at two possible temperatures. The lowest temperature, TB, represents essentially completely brittle behavior while the higher temperature, TN, represents "notch" brittle behavior. Support for this theory is obtained when it is observed that fcc metals, which do not commonly have a ductile-to-brittle transition, also do not commonly exhibit any strong temperature de- pendence of the yield stress. This relationship of yield or flow stress behavior with the ductile-to-brittle transition has been generally observed for most metals representative of these two crystallo-graphic structures. One exception to this generalization appears in the case of tantalum where no apparent ductile-to-brittle transition has been observed. However, this may simply be an indication that this type of behavior is not directly related to the flow stress and that some other mechanism such as twinning must also be operative. A comparison of the typical temperature dependence of the yield stress of some representative metals is shown in Fig. 2. In the study of the temperature dependence of the strength of metallic materials, considerable ef-

Jan 1, 1963

By B. M. Larsen, W. E. Shenk, T. E. Brower

Shortly after our previous paper on this subject was printed1 we located a source of uncertainty in the results arising from the unexpected fact that hydrogen slowly reduces silica at 1100" C. in presence of iron, even when the iron nowhere touches the silica, although in absence of iron it does not do so. This difficulty has been completely obviated by the use of a small high-frequency furnace, which enables us to heat the specimen for analysis without raising the temperature of the silica vessel to a point at which any appreciable reduction of the silica glass occurs. We now describe this modification of procedure, and present some typical results obtained with it. For any given specimen of steel, the results are entirely definite and reproducible, but their precise significance is still open to some question, as indeed is true of all methods of oxygen determination SO far developed. Further elucidation of this question is to be expected from the cooperative comparison of the several methods now under way under the auspices of the Bureau of Standards at the instance of the Iron and Steel Division of the A.I.M.E. Apparatus The final form of apparatus we have used is identical with that described and illustrated in our previous paper, except for the substitution for the Globar furnace of a small high-frequency furnace actuated by a vacuum tube oscillator2 0f about 1.5 kw. capacity, and for a slight modification of the containing vessel. This transparent silica vessel is illustrated in Fig. 1 of this paper. Its enlarged portion is about 5 cm. in diameter and 13 cm. long. The silica tube for inlet of hydrogen is fused into this bulb and ends beneath the metal "bucket" holding the steel sample. This sample is in the form of fine millings. The "bucket" is suspended by a platinum wire from the cap of Pyrex glass. The high-frequency

Jan 1, 1934

By A. B. Cook

Gas cycling is generally considered a much less efficient oil recovery mechanism than water flooding. HOWever, recoveries from some fields have been exceptionally high as a result of gas cycling. Recovery from the Pick-ton field, for example, was calculated to be 73.5 perceni of the stock-tank oil originally in place. In evaluating pressure maintenance projects, determining how much of the recovery is due to displacement by gas and determining how much is due to vaporization of the imrnohile oil in the flow path of the cycled gas is very difficrilt. Even though most of the oil is recovered by displacetr~ent, the success of a project may depend on the amount of oil vaporized. A limited number of experiments have heen performed with a rotating model oil reservoir that simulates gas cycling operations and allows a separation of the oil from, tile free gas flowing into the laboratory wellbore at reservoir conditions, thus revealing which is displaced oil and which is vaporized oil. It Iras been determined that the amount of varporizatio'n is .significant if proper conditions exist These experiments show that oil vaporization depends on pressure, temperature, volatility of the oil and amount of gas cycled. Increases in each of these conditions increase the volume of oil vaporized. Data from six experiments affecting vaporization are presented to illustrate reservoir condition that range from favorable to unfavorable. 111 these eaperitnenis recovery by vaporization ranged from 73.6 to 15.3 percent of /he immobile oil (oil not produced by gas displacerrlt). INTRODUCTION Between 1930 and 1950, gas cycling was a popular. oil recovery practice. especially for the deeper reservoirs. Later, with many case history-type studies published for both gas cycling and waterflooding, it was generally believed that waterflooding was far superior to gas cycling, even when gas cycling was conducted as a primary production procedure by complete pressure maintenance. A good example illustrating the advantage of water-flooding over gas cycling is given in a paper by Matthews' on the South Burbank unit where gas injection was followed by waterflooding. The author concluded in part that "Early application of water injection, without the intervening period of gas injection, would have recovered as much total oil as ultimately will be recovered by waterflooding following the gas injection, and total operating life would have been shortened". This appears to be a logical conclusion. However, it should not be applied to all fields. Pressure maintenance with gas in the Pickton field, as reported by McGraw and Lohec;' will result in a much larger percentage of oil recovery than was obtained in the South Burbank unit. The great success in the Pickton field resulted partly from vaporization of the immobile oil in the flow path of the cycled gas. The amount of vaporization is related to the following conditions: volatility of the oil as reflected by the APT gravity of the stock-tank oil; reservoir temperature; reservoir pressure during gas cycling; and the amount of gas cycled. Therefore, the U. S. Bureau of Mines is investigating these effects on vaporization in a research project using a model oil reservoir. Three different stock-tank oils having 22, 35 and 45" API gravities are being used as base stock to synthesize reservoir oils. Experiments are being performcd to determine vaporization at 100, 175 and 250F and at 1,100, 2,600 and 4,100 psia. This is a progress report showing the results from six experiments. Other Bureau of Mines reports"- concerning vaporization are listed. LABORATORY EQUIPMENT AND PROCEDURES The equipment ' consists of an internally chromium-plated steel tube packed with finely sifted Wilcox sand. The tube is approximately 44 in. long and has an ID of 13/4 in. The sand section contains approximately 570 ml of voids, has a porosity of 32 percent, and a permeability to air of 4.3 darcies. A unique feature of the laboratory reservoir (Fig. 1) permits the tube part to rotate at 1 rpm while the outlet and inlet heads are held stationary. The outlet end contains diametrically opposed windows to permit observatlon of the flowing fluids, and two valves, one on the top and the other at the bottom. Oil and free gas. when being produced simultaneously, can be separated by manipulating the two valves to keep a gas-oil interface in view through the windows. Thus, only gas is produced through the top valve and only oil flows through the bottom valve. The laboratory equipment was designed to study vaporization. Therefore, a uniform reservoir was made using dry sifted sand as opposcd to using a consolidated sand core with interstitial water. Furthermore. the reservoir was tilted to minimize fingering of gas. This tilting also in-

By J. D. Mote, J. E. Dorn

This investigation was undertaken to study the effects of piledup arrays of dislocations on inducing slip, twinning, and fracturing in magnesium bicrystals. A series of variously oriented bicrystals of magnesium having a vertical grain boundary were prepared and tested in tension. It was found that piled-up arrays of dislocations at the grain boundary could, under appropriate conditions, induce slip, twinning- and cracking. The results that were obtained substantiate, at least qualitatively, the general dislocation mechanism for transmission of strain across grain boundaries and the Petch-Stroh concept of fracturing. WHEREAS single crystals of magnesium generally exhibit extensive deformation, coarse-grained poly-crystalline magnesium at subatmospheric temperatures fractures after a few percent elongation.' Although a small amount of ductility is obtained, several features of this fracturing are characteristic of typical brittle behavior. Over a rather broad temperature range the fracture stress is insensitive to the test temperature and the fracture stress increases linearly with the reciprocal of the square root of the mean grain diameter. The course of fracturing is predominantly intergranular, but small fragments of adjacent grains frequently adhere to the fractured surface.2 The brittle behavior of polycrystalline magnesium is attributable to the limited number of facile deformation mechanisms it exhibits at low temperatures. For a general deformation of a randomly oriented polycrystalline aggregate, each grain must exhibit at least five independent mechanisms of deformation to permit accommodation of the imposed deformation from grain to grain.= Although minor amounts of prismatic slip occur in corners of grains where stress concentrations are known to be high, glide in polycrystalline magnesium at low temperatures takes place almost exclusively by basal slip.' The common type of twinning, which takes place on the (1012) pyramidal planes, can under the most favorable orientations, lead to a. strain of only 6.9 pet; the contribution of twinning to the tensile strain would indeed be much less than this in a randomly oriented polycrystalline aggregate of magnesium. Since the three mechanisms of basal slip are coplanar, they are equivalent to only two independent mechanisms, a number insufficient for a general deformation. Consequently, once the permissible twinning has taken place in conjunction with basal slip, no further plastic deformation is possible because of interference to slip at the boundaries of dissimilarly oriented grains. At this stage brittle fracturing takes place due to high stress concentrations at the juncture of slip bands with the grain boundaries; the predominance of intergranular fracturing in magnesium, in preference to transcrystalline fracturing which is prevalent in zinc, has not yet been rationalized. A more atomistic description of the plastic behavior and fracture characteristics of magnesium follows from the analyses made by stroh4 on the stresses induced by piledup arrays of dislocations. Slip first takes place by dislocation motion in the most favorably oriented grains. As the dislocations approach the boundary of a dissimilarly oriented adjacent grain they begin to form an array of dislocations with its attendant stress field. Piledup arrays of screw and edge dislocations introduce high localized shear stresses at the spur of the array; piledup arrays of edge dislocations also induce high tensile stresses localized in the vicinity of the grain boundary. Whereas the shear stresses can induce slip to take place, the tensile stresses, if sufficiently high, can cause fracturing. The localized shear stress will be relieved if sufficient numbers of mechanisms of deformation become operative in the original and the adjacent grain to permit accommodation of the dislocations in the grain boundary. In this event a ductile behavior will be obtained. But if the number of deformation mechanisms is insufficient for complete migration of dislocation arrays into the grain boundary, the tensile stresses due to the edge components of piledup dislocation arrays will continue to increase with increasing applied stress until fracturing takes place. Whereas face-centered-cubic metals have a sufficient number of mechanisms of slip for accommodation of dislocations in their grain boundaries to exhibit ductile behavior, hexagonal-close-packed metals, in general, do not. Consequently, hexagonal-close-packed metals are usually brittle except when conditions such as alloying or temperature permit facile slip by a number of mechanisms. The arguments presented above suggest that the mechanical behavior of magnesium depends on whether or not dislocation arrays in adjacent grains can enter the grain boundary. When such accommodation is possible, ductile behavior is expected; but when such accommodation is impossible, fracturing will ensue. To further test the validity of these arguments it was considered advisable to study the

Jan 1, 1961

By Herbert Hoover

This paper is in the nature of a rough preliminary report on the progress that has been made in the application of the mass spectrometer to various problems arising in the petroleum industry. A few years ago the authors considered a number of the problems that were arising in the qualitative and quantitative measurement of small amounts of hydrocarbons. The methods available of making analyses by chemical techniques appeared to leave much room for improvement. Without going into the reasons at this point, attention was turned to the possibility of employing physical instead of chemical methods of accomplish-ing the desired results. A preliminary investigation disclosed that the mass spectrometer presented a possibility of solving many problems which could not easily be accomplished by other methods. Work was begun in developing the necessary apparatus and technique. A great deal of encouragement and many valuable suggestions were received from Dr. Robert A. Millikan, Dr. W. R. Smythe, and Dr. W. N. Lacey, of the California Institute of Technology, and from Dr. E. 0. Lawrence, who recently received the Nobel Prize, of the University of California. The authors particularly wish to acknowl-edge the very great willingness of these out-standing scientists to be helpful in solving many of the problems that were involved. So far as the authors are aware, this was the first application of the mass spectrometer to commercial work. The results were considerably better than had at first been anticipated. Briefly, it is pos-sible to run a qualitative and quantitative analysis of an unknown mixture of hydro-carbon gases, with an accuracy of better than plus or minus 5 per cent of each of the various constituents. An exceedingly high degree of sensitivity has been obtained, and a relatively short time is required to com-plete an analysis. Furthermore, it is un-necessary to separate a mixture of gases into its various components in order to complete the analysis.

Jan 1, 1940

By John Johnston

When I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in I9I6—that is, about 25 years ago—in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father— Dr. Samuel Gridley Howe, his mother— Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-clrbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable. tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes—and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. it tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to dccipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By John Johnston

When I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in I9I6—that is, about 25 years ago—in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father— Dr. Samuel Gridley Howe, his mother— Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-clrbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable. tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes—and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. it tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to dccipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

The following figures (Nos. 1-4) and tables (Nos. 1 and 2) were inadvertently omitted from the chapter entitled "Optimum Open-Pit Mine Production Scheduling" by Thys B. Johnson, Section 4, pages 539-562. [ ]

Jan 1, 1969

By AIME AIME

FOLLOWING careful study of the relations of the Institute to students and the younger members of the profession, the Membership Committee recommended to the Board a change of plans abolishing the Junior Associate class of membership, substituting a -Junior membership and providing for Student Associates. The Board adopted this report at its meeting on Nov. 23, and asked Counsel to draft the necessary amendments to the By-laws, and gave formal notice of intentions to amend as provided in Section I, Article XI1 of the existing By-laws. The By-laws as it is proposed to amend Article I, 11, 111, IV, X, and XI follow. The new plan requires no changes in the other Articles. The matter will come before the Board for vote on Jan. 25.

Jan 1, 1929

By W. A. Stickney, J. W. Town

Tests demonstrated that aqueous solutions of sodiu~n sulfide would dissolve over 95 pct of the cinnabal- in 5 pct Hg flrotation concentrates and 60 to 90 pct of the cinnabav in low-grade ol-es. Double-leach tests showed that potassiutn sulfide would dissolve 90 pct of the avsenic sulfide in Hg-As satnples and only 1 to 10 pct of the Hg; the sodium sulfide would then dissolve 80 to 90 pct of the rernaining Hg and 30 to 70 pct of the vemaining As. 1 HIS paper describes the extraction, by alkaline sulfide solutions, of mercury from cinnabar-bear ing ores and flotation concentrates. Leaching time and solution temperature had minor effects on mercury extraction when compared to the effects of reagent quantity and ore type and grade. Cinnabar, although readily soluble in sodium sulfide, was only partially soluble in potassium sulfide and essentially insoluble in ammonium sulfide. A double leach process was developed to extract selectively the arsenic from Hg-As products with K2S and to treat the residue with sodium sulfide-hydroxide solutions to extract the mercury.' Mercury was then recovered from the pregnant solutions either by precipitation with metallic aluminum or by electrodeposition. The solubility of HgS in alkaline sulfide solutions was first reported by Volhard in 1878.' The first reported commercial application was made in 1915 when Thornhill applied the method to the treatment of an amalgamation tailing.3 Mullhollen, in 1911. described the chemical reaction of HgS with Na,S and alkaline hydrate to be:4 Most investigators have reported using a 4-pct sodium sulfide and a 1-pct sodium hydroxide soluti~n.3-4 An increase in temperature or excessive dilution of the solution causes the reaction to be reversed. Church Holmes described a similar process used for the extraction of antimony from silver concentrates at the Sunshine Mining Company's mill at Kellogg. Idaho.5 More recently. Erspamer and Wells reported the results of leaching studies on a Hg-Sb ore from Alaska.6 EXPERIMENTAL PROCEDURE Leaching tests were made on samples of mercury ore from eight deposits in Oregon, Washington, and Idaho. In addition. tests were made on flotation concentrates from seven of the samples as well as a flotation concentrate from an operating mill. Since previous investigators reported reagent requirements greatly in excess of that required by the equation HgS + Na2S = HgS . Na2S, initial studies were made on chemically pure HgS. Results showed that the reaction actually required about 1 g of Na,S per g of HgS in an aqueous solution rather than 0.338 g of Na,S as indicated by the equation. To check further the matter of reagent requirements, Na2S and HgS were mixed together in equal mole ratios. Water was then added, a drop at a time, until the components reacted; X-ray diffraction analyses showed no HgS nor Na,S present. The yellow hydrate compound which formed would not redissolve until about three additional mole equivalents of Na,S were added to the solution. This indicated that a stable solution would require at least 4 moles of Na2S for each mole of HgS. While these implications may be valid for pure HgS, the possibility of entirely different results caused by the existence of other elements present in ores and concentrates was recognized. Consequently, experiments of the same order were made on samples of a flotation concentrate from a producing mill. The concentrate, containing about 18 pct

Jan 1, 1962

By W. L. Dumoulin

A RATHER detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,1 so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year, 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily, capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to ¼ in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in.. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 ½ by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane.

Jan 8, 1919

By A. L. Barnes

A number of reservoirs have been partially invaded by bottom water. Water flooding such reservoirs can be especially inefficient if the oil has a high viscosity because injected water will under-run the oil and emerge at producing wells without having displaced much oil. A possible means of improving water sweep efficiency would be to precede the water flood with a slug of water purposely thickened with a chemical additive. This possibility has been studied with a scaled laboratory flow model. The investigation was carried out on a model representing a 20-acre five-spot with one set of reservoir condition~. Displacements were performed with water, with viscous-water slugs of 10 and 25 per cent of the pore volume followed by water, and with all viscous water. Displacement tests were made at several rates of injection. For all cases, compared at the same producing water-oil ratio, an increase in rate resulted in an increase in volumetric sweep. The larger the quantity of viscous slug injected, the greater the crossflow of oil ahead of the displacing front and, thus, the lower the WOR during that period of a displacement. This investigation indicates that the injection of aqueous viscous slugs in this type of system would give some additional benefit over conventional flooding by (I) reducing the life of the flood, (2) reducing lifting costs and (3) increasing ultimate recovery. The benefits of a viscous-slug displacement would warrant its use if the viscous water could be created for a few cents per barrel. INTRODUCTION The most appropriate method for water flooding oil reservoirs which have been partially invaded by bottom water has been a problem of considerable interest. Such reservoirs, having good vertical permeability and unfavorable mobility ratios, are difficult to produce efficiently under normal waterflood procedures. Even though the injection wells have been plugged back above the oil-water contact and the water zone has been squeezed off, injection water will enter the formation and not only displace oil, but also much of it will displace the bottom water, thus creating a high producing water-oil ratio at the start of a flood (see Fig. 1). Since the rate of injection and the viscosity of the displacing fluid are the more easily controlled physical parameters of the reservoir, it is quite natural to study their effects on the volumetric sweep of the oil zone and on the producing water-oil ratio. Increasing the viscosity of the displacing fluid has two disadvantages—it reduces the maximum rate of injection into the reservoir, and it costs more than water. It was thought that the injection of a viscous-fluid slug, followed by water, would minimize these two disadvantages, increase the volumetric sweep of the oil zone and reduce the producing water-oil ratio. Water with an additive to increase viscosity would probably be the most effective. The primary purpose of this investigation was to determine the feasibility of injecting viscous-water slugs followed by water to improve or hasten oil recovery while reducing the producing water-oil ratios. The effect of injection rate upon recovery was also investigated. A laboratory model, scaled to a 20-acre five-spot prototype with one set of reservoir conditions, was constructed. Laboratory studies of displacements with (1) water, (2) viscous-water slugs of 10 and 25 per cent of the pore volume followed by water and (3) all viscous water were performed at several rates of injection. THEORY OF SAND MODEL SCALING There are two conventional means of determining scaling criteria. These are dimensional analysis and inspec-tional analysis. Determining scaling criteria by dimensional

By P. K. Foster, A. McNabb

A consideration of the literature shows the inadequacy of Fick's Laws to describe the diffusion of hydrogen in steels below 400°C. These laws are modified an the assumption that hydrogen is delayed at fixed sites in the lattice. Approximate and exact solutions of the resulting nonlinear system are derived for simple geometrical shapes. The results qualitatively account for the observed anomalous behavior. Experimental methods for verifying the theory are suggested. 1 HIS paper presents a new analysis of the diffusion behavior of hydrogen in steel based on a physical model which supposes that hydrogen atoms wander in a random manner through the crystal lattice, but tend to get trapped or delayed at certain fixed sites uniformly distributed throughout the metal. These sites, which will be called traps, are regarded merely as potential wells of significantly greater depth than those encountered in regular regions of the crystal lattices and no assumptions are made concerning their nature or origin. The results of experimental studies of the diffusion of hydrogen in iron and steel have usually been reported in the literature in terms of a diffusion constant D derived under the assumptions that the hydrogen concentration C is governed by Fick's laws.1 Fig. I is a composite of published graphs of the man. ner in which the values of D, so derived, vary with temperature. It is convenient to consider this material in two categories; the high temperature results above 400°C, and the results at lower temperatures. The graphs 2, 3, 4, 5 in the first class lie within a factor of three of each other and are relatively consistent compared with the low-temperature values. There is an increasing divergence in values of D with decreasing temperature till at room temperature they are spread over three orders of magnitude. Small values of D have been obtained for work-hardened specimens.' It is evident that D is a function of other variables besides temperature in this range and that these neglected variables are in some way connected with the work hardening experienced by the specimen. In view of evidence for an interaction between hydrogen in solution and dislocations9'10 and adsorption on crack surfaces,' some doubts must be entertained about the validity of Fick's laws and their associated physical model of noninteracting particles in random motion through the medium. More direct evidence of their inapplicability to the diffusion of hydrogen in steel was first produced by Darken and smith." Consider the permeation of hydrogen through a plate of thickness a under a boundary concentration Co at the ingoing, and zero at the outgoing, face. If Fick's first law1 is valid, the steady state flux P, through unit area is DCo/a. In addition, the concentration C varies linearly throughout and Qo, the mean quantity of hydrogen in the medium, is co/2. Compare Qo with Q1 the mean quantity required to saturate the same specimen to a uniform concentration G. In this case Ql = Co and hence the ratio

Jan 1, 1963

By Philip S. Morse

THE Australian lead-smelting plants began to use charges carrying high zinc percentages somewhat earlier than was common with American plants. When lead smelting first started in Australia the immense deposits of oxidized lead at Broken Hill were available but later these oxidized ores became exhausted and were replaced by sulfides. This was before the days of flotation and these sulfides when concentrated carried about 1 per cent. of zinc to 6 per cent. of lead. The works of the Sulphide Corpn. at Cockle Creek was perhaps the pioneer in high-zinc slags but the Port Pirie plant of the Proprietary Co. was a close and very able second and has continued the work to the present time. The Cockle Creek lead furnaces remained in operation until shortly after the war when most of the Broken Hill companies combined and took over the Port Pirie plant to treat their concentrates. As it was the practice both at Cockle Creek and Port Pirie to carry 20 per cent. or more of lead on the charge, it was found that under these conditions of large amounts of zinc in the charge, good roasting was absolutely necessary and matte production was unwise. The Hunting-ton-Heberlein system of roasting was introduced and later the Dwight & Lloyd process. In this way, by roasting the sulfide portions of the charge as thoroughly as possible and making no matte, a method of smelting was developed where the slag over long periods carried as high as 20 per cent. ZnO without serious furnace troubles, and slags carrying even up to 33 per cent. ZnO have been reported. The zinc slags were not very different in appearance from the ordinary slags produced in American practice except that they gave off more smoke and fume on tapping. The slag usually ran hot and freely, coming from the tap in a full stream. Normally there was little crust on the sides of the furnace and the tuyeres gave no trouble though they were always rather dark. At the works of the Sulphide Corpn. it was the custom, on account of the labor situation, to shut down the furnaces during the Christmas holidays, thus giving a campaign of about 12 months. The furnaces at the end of the run usually showed no crust on the sides, though crusts always occurred at the back and front ends. A furnace campaign of 22 to 23 months has been made at this plant where both sides of the

Jan 1, 1929

By Robert Glass Cleland

[Wylie Brown Responsible to a large extent for the incorporation of: British American Metals Company, Inc. 1918 American Copper Products Corporation 1920 British American Tube Company, Inc. 1922 National Electric Products Corporation 1927 Phelps Dodge Copper Products Corporation 1932 President 1932-1947 Chairman of Board1948-1950]

Jan 1, 1952

By H. J. Modi, D. W. Fuerstenau

pH effectively regulates the flotation of corundum through its control of the surface charge. Since collector ions function as counter ions in the double layer, the collector must be anionic when corundum is positively charged and cationic when it is negatively charged. Even a long-chained xanthate will float positively charged corundum. Association of the hydrocarbon chains of the adsorbed collector ions gives rise to increased adsorption and increased rate of flotation. Because of this phenomenon, neutral organic molecules aid flotation although the unionized collector cannot promote flotation independently. Na2SO4 was found to depress the flotation of corundum with animic collectors through ionic competition whereas the same salt activates corundum for flotation with cationic collectors. A close connection between ion association, electrokinetic behavior, and floatability is suggested. As part of the increasing interest in the physical chemistry of flotation, strong experimental evidence has been obtained which indicates that organic ions are adsorbed as counter ions by non-metallic oxide minerals mainly because of the electrical forces which exist at interfaces(1-3). Thus flotation of such minerals without activation should then be appreciable only when the mineral and the collector are oppositely charged. Since only limited work has been reported on the effect of surface charge upon flotation behavior(3) this general hypothesis on the flotation of insoluble oxide minerals has not been tested thoroughly. Investigating the flotation of a mineral for which extensive electrokinetic data exist yields a way to test this hypothesis more extensively. The electrokinetic behavior of corundum in solutions containing both organic and inorganic electrolytes has been studied quite thoroughly' Electro-kinetic measurements have shown that in the case of corundum, simply by controlling pH the solid surface can be charged either positively or negatively. For this reason corundum was chosen for study. The object of this paper is to present a study of the flotation of corundum and to explain the results in the light of our knowledge of adsorption mechanisms gained from streaming potential investigations. This paper is concerned mainly with the effect of surface charge on flotation with anionic and cationic collectors, but in addition such flotation phenomena as collector hydrolysis, Van der Waals attraction between hydrocarbon chains, ionic competition, and activation are discussed. While the present paper is confined to a reporting of the data obtained and some of the more immediate conclusions, it will be seen that the results, in combination with those on other systems, do promise a

Jan 1, 1961

By Leslie G. McMillion

A field project to develop and demonstrate a method for alleviating problems of highly mineralized ground water where they occur as isolated zones or pockets in fresh-water aquifers is being conducted in the Ogallala aquifer of eastern New Mexico by the Robert S. Kerr Water Research Center. Removal of contaminated water is by a large-capacity well and the pumped poor-quality water is used locally for secondary recovery of oil. Benefits of the operation are threefold in that the aquifer is being reclaimed for future fresh-water production, contaminated water is being used beneficially, and fresh water which otherwise would have been used for waterflooding is available for other purposes. Ground-water quality in the site has improved markedly after two years of operation. Use of water in the arid and semiarid Southwest has grown so rapidly that demands in many localities far exceed available supplies. In the High Plains region of New Mexico, Oklahoma, and Texas, the only large sources of water are underground reservoirs, being depleted at an alarming rate. In some parts of this region, the aquifers contain pockets of highly mineralized waters; and the mineralized waters in some of them have started spreading in response to the drawdown effects of pumping wells. The aquifers of this region are primarily composed of sand and gravel beds; any cleanup by natural processes will require many tens or even hundreds of years. Most of these pockets of highly mineralized water were caused by oil-field brines seeping downward from earthen disposal pits. Thousands of these pits were in use in the region until only a few years ago when they were prohibited by the oil regulatory agencies of the respective states. The resulting areas of poor quality water are serious enough to warrant much corrective attention. Correction will involve one or more of three approaches: 1) Restrict the pumping of fresh water in the zones where the drawdown of the pumping well will significantly influence the movement of the contaminant. 2) Remove the highly mineralized water entirely from the affected area. 3) Develop and pump the poor-quality water in such a manner that its movement is held in check, even though only a part of the contaminant is actually removed. The principal hurdle to overcome in applying methods 2 or 3 is financing of the operations, since there are very

Jan 1, 1972

By A. J. Heckler, J. A. Peterson

A capsule technique was successfully employed to investigate the effect of nickel on the activity of nitrogen in Fe-Ni-N austenite in the temperature range 600" to 1200°C. This technique consisted of equilibrating nitrogen among various Fe-Ni alloys within a sealed silica capsule. Nitrogen transfer among the specimens occurred by N, gas at 900°, lOOO? and 1200?C. Nitrogen gas pressures within the capsules were estimated to be as high as 22 atm. The activity coefficient of nitrogen, fN , in Fe-Ni-N austenite is adequately described by the linear interaction equation: log . wt pct Ni where the standard state is chosen such that fN = I as wt pct Napproaches zero in binary Fe-N. This relationship was determined over the temperature range 873" to 1473°K and for nickel contents of 0 to 35 wt pct. ALTHOUGH chemical thermodynamics of liquid iron alloys have been extensively studied, experimental data for the solid state are needed. These thermody-namic data will provide a basis for understanding phase transformations, precipitation reactions, metal-gas equilibria, and so forth. The interaction of sub-stitutional alloying elements with the interstitial elements is of particular interest. In this investigation the thermodynamic behavior of Fe-Ni-N austenite has been studied. The solubility of nitrogen gas in iron austenite is known to obey Sieverts&apos; law up to about 65 atm.1-6 In addition, the solubility of nitrogen in Fe-Ni austenite has been investigated5"8 using the classical method of equilibrating Fe-Ni alloys with nitrogen gas at 1 atm. A capsule technique similar to that used to study the activity of carbon in alloyed austeniteg&apos;&apos;&apos; was employed in the present work to determine the effect of nickel on the activity of nitrogen in Fe-Ni austenite over the temperature range 600" to 1200°C. EXPERIMENTAL PROCEDURE A series of Fe-Ni alloys up to 35 wt pct Ni was vacuum melted and cast into 1 by 3 by 6 in. ingots. Chemical analyses at the top and bottom of each ingot demonstrated that the ingots were homogeneous with respect to nickel content. The nickel contents are given in Table I. Additional chemical analyses showed that wt pct Si < 0.05, s < 0.01, C < 0.01, Al < 0.006, 0 < 0.004, Mn < 0.002, and P < 0.002. A 2 in. section of each ingot was cold rolled to 0.015 in. The material was then decarburized to a carbon content of less than 0.004 wt pct. A portion of the material of each nickel content was nitrided to various levels in a H2-NH3 gas atmosphere to provide a source of nitrogen during subsequent equilibration. The experimental technique consisted of equilibrating the series of Fe-Ni-N alloys in a partially evacuated sealed silica capsule at the temperature of interest. Both Vycor and quartz capsules were used. In general, the final equilibrium nitrogen content for each Fe-Ni alloy was approached from both higher and lower nitrogen levels. The criterion for establishing that equilibrium was attained was that the final nitrogen content for each Fe-Ni alloy was the same irrespective of the initial level. A schematic drawing of the sample configuration in a capsule is shown in Fig. 1. The samples were arranged so that there was a minimum of physical contact. The samples were also dusted with a fine, high purity alumina powder to help prevent sticking. Several different types of furnaces were used in this study. In each case, a thermocouple was placed immediately adjacent to the capsule during equilibration and the temperature was controlled to within *4?C of that reported. At each equilibration temperature, the following times were found to be more than sufficient to attain equilibrium: 600°C-250 hr, 900°C-150 hr, 1000°C-150 hr, and 1200°C-50 hr. After equilibration the capsules were quenched in water and the nitrogen contents of the specimens determined by a Strohlein analyzer. Analyses of samples after equilibration at 1000" and 1200°C showed no silicon pickup from the silica capsules. RESULTS AND DISCUSSION Transfer Mechanism. The mechanism by which nitrogen was transferred among specimens in an initially hydrogen flushed and partially evacuated capsule equilibrated at 1000°C was investigated. After equilibration the gas in the capsule was collected over water and an estimate of the pressure at temperature

Jan 1, 1970

By Edward A. Loria

A SERIES of papers on the study of austenite grain A size in cast steels has been published recently.&apos;" These studies show that in the as-cast state, the austenite grains are quite large, for they form as the steel freezes at a very high temperature, but a simple reheating above the critical range produces a new set of austenite grains which, in many instances, is finer than ASTM grain sire No. 8. Furthermore, there is no apparent relationship between as-cast austenite grain size and subsequent grain size produced by heat treatment. The as-cast austenite grain size can be determined easily in plain carbon and low alloy steels which produce a continuous grain boundary f errite envelope in the as-cast structure. In the case of cast steels whose alloy content produces greater hardenability and suppresses the proeutectoid ferrite transforma-

Jan 1, 1952