Search Documents

By H. C. Schultz, F. K. Middleton Hunter

Certain local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to develop usefully its full disruptive effect in hard ground. The individual blasts at Chuquicamata arc large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with 1,. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast. Present Liquid-oxygen Plant An experimental unit with a rated capacity of 75 liters per hour was erected during the latter part of the year 1926 to prove the effectiveness of L. 0. X. at this mine, its cost, and possible efficiency of large-scale storage of the liquid. With this experimental unit 200,000 tons of ore

Jan 1, 1928

By A. Whillier

Methods are given for estimating heat flows into mining excavations of various types, with an example to illustrate how the refrigeration requirements are then determined after allowing for the cooling effects of the ventilation air.

Jan 1, 1981

By R. S. Montgomery

Laboratory experiments simulating rock drilling were conducted on a number of commercial grades of tungsten carbide in order to determine their wear rates when they are used as inserts in percussive rock drill bits. The test rock was Barre granite and tests were made at conditions similar to those of the carbide buttons near the periphery of a large, down-hole, button bit. In addition, some wear rate measurements were made at a low blow energy. Wear rates of these carbide buttons were an extremely sensitive function of their cobalt contents and hardnesses and were proportional to e-°.57Hup to a hardness of about 91 RA. The point of minimum wear rate, which occurs at about 92 RA, corresponds to the point of maximum compressive strength. Modern percussive rock drill bits have inserts of cemented tungsten carbide on their wear faces. These inserts have drastically reduced bit wear in comparison to that of earlier all steel bits. The most common cemented carbide grade used in percussive rock drill bits contains about ten weight percent cobalt, although grades containing more or less cobalt are also used. Contrary to the case with carbide in metal-cutting tools, alloying materials are rarely used in mining grades. There are a number of designs of rock bits in current use. The most common form is an X bit which has four chisel-form radial wings. The button bit is another important design and one which has been recently developed. This design uses a flat steel face studded with relatively small hemispherically tipped carbide buttons. These types are illustrated in Fig. 1. Studies have been made of the sliding wear of cemented tungsten carbide on rock 1-4 and multiple-impact fracture', 5-6, b~t there has been comparatively little published on the percussive wear of this material although the wear of the impact face is the most important. There is some available data on the rate of dulling of rock bit inserts in actual drilling 7 but no laboratory studies. Sliding wear studies are useful for understanding the wear of coal and mineral cutting tools and gauge wear of percussive drill bits. but the

Jan 1, 1970

By T. S. Lundy, J. I. Federer

A graphical method has been developed and tested for separating the effects of grain boundary and lattice diffusion in polycrystalline materials. The method is based on the assumptions that for unidirectional diffusion from a plane source of radioactive material, the penetration of activity far into the specimen from the source is due solely to grain-boundary effects, and 2) pure grain-boundary penetration is described by a linear plot of log activity vs the perpendicular distance x from the source. The former is based on the fact that at any temperature the grain-boundary diffusion coefficient is always very large relative to the lattice diffusion coefficient; and the latter is based on the derivation of Fisher.1 Using these criteria along with appropriate penetration data (in this case, data for the diffusion of Cb95 in pressed and sintered UO2) one first plots the data as log activity vs x2 and as log activity vs x, as shown by curves 1 and 2, respectively, in Fig. 1. A tangent line to curve 2 for large x (curve 3) is then transferred to the x2 plot as curve 4. The subtraction of curve 4 from curve 1 yields curve 5 which represents only lattice diffusion and may therefore be related to the diffusion coefficient by using the appropriate solution to Fick's second law. It should be noted that the method has inherent inaccuracies for small and large values of x2 and only the subtraction at intermediate values can be used. For the illustrated specimen the calculated diffusion coefficient is 3.4 X 10-11 sq cm per sec at1445°C while data using a single crystal of UO2 at the same temperature yielded a value of 2.9 x 10-11 sq cm per sec.2 The same method of subtracting grain-boundary diffusion effects to obtain lattice diffusion coefficients has been successfully used to determine self-diffusion coefficients of Th230 in polycrystalline thoria.

Jan 1, 1962

By George H. Found

During recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" 06 a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating -mecha-nisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experi- mental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,' damping due to localized inelastic stress relaxation at inhomogeneities within the meta1,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.' How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables ham been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About Ioo hr. after straining, a stable value is reached of magnitude proportional to the amount of strain.' In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By George H. Found

DURING recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" of a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating mechanisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experimental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,1 damping due to localized inelastic stress relaxation at inhomogeneities within the metal,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.4 How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables have been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About 100 hr, after straining, a stable value is reached of magnitude proportional to the amount of strain.7 In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By D. W. Levinson, L. E. Tanner

DURING the course of an investigation of the zirconium-iron-tin system the zirconium-iron system was reexamined up to 55 pct* Fe. The alloys pre- visible melting3 and X-ray diffraction studies were made of samples of the alloys. The ferromagnetic properties of ZrFe2were determined by Professor P. W. Selwood* using a modified Faraday balance.4 The zirconium-rich portion of the phase diagram is presented in Fig. 1 and compared with the work of Hayes et al.1 The maximum solubility of iron in ß is somewhat decreased while the eutectic temperature is raised. There seemed to be no change in the eutectic composition of 16 pct Fe. Since the base material was so low in iron content, it was possible to establish the maximum solubility in a between 0.017 and 0.025 pct Fe at the eutectoid temperature. The observation of fine ZrFe, particles in the micro structure of a specimen of 0.012 pct Fe alloy quenched from 700°C indicated that the solubility drops below this composition at 700° C and lower. Further study was made of the intermediate phase ZrFe2. wallbaum5 identified the compound initially as ZrFe2 with a C 15 (MgCu2) structure, placing it at 55 pct Fe stoichiometrically. Hayes et al.1 believed they found the phase at about 47.2 pct Fe and called it Zr2Fe3 but reverted to ZrFe, in the discussion of their paper.6 Jordan and Duwez7 confirmed Wallbaum's work as well as finding the same single-phase structure to about 62.3 pct Fe or Zr0-61 Fe2-18. In order to establish the ternary phase relations in the zirconium-iron-tin systema the exact position of this phase had to be known. This was accomplished by X-ray diffraction, visible melting, and metallographic techniques. Elliott8 obtained a single-phase ZrFe2 X-ray diffraction pattern from an alloy of about 55 pct Fe. This was confirmed in the present study with an alloy of 54.81 pct Fe. However, extra lines (attributable to a or ß zirconium) were found in diffraction patterns of the 47.42 and 49.83 pct Fe alloys. The melting characteristics of these same alloys were studied by suspending 47.42, 49.83, and 54.81 pct

Jan 1, 1960

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942

By R. F. Mehl, M. L. Swanson, J. P. Hirth, G. M. Pound

The sorption of zinc in a-brass was investigated. By analyzing the elliPtically polarized light reflected from the surfaces of a-brass solid-vapor couples, their optical constants and surface compositions were determined. It was shown that the surface compositions approached an equilibrium value exponentially with time. The bulk diffusion coefficient, surface diffusion coefficient and condensation coefficient for a-brass solid-vapor couples were calculated near 350°C from the experimental results. It has been assumed during various diffusion experiments with bimetallic solid-vapor couples (Dunn,1 Seith and Kraus,2 Jenkins,3 Balluffi and Seigle,4 and others) that the surface composition of such couples reaches its equilibrium value immediately. Although this assumption is probably valid at elevated temperatures, it is certainly not expected to be confirmed at lower temperatures.* consequently, it was decided that a fundamental experiment, designed to solve this problem as well as to examine all aspects of bimetallic sorption, would be the investigation of the rate of approach to equilibrium of the surface composition of solid-vapor couples. The sorption (i.e., adsorption, absorption, and desorption) of metals is obviously dependent on the state of the metallic surface and substrate. Much recent theoretical8"9 and experimental10-12 work on condensation and evaporation of pure metals has shown that the surface contour in atomic dimensions is a critical factor in sorption, so that any deformation or contamination13,14 of the surface exerts a profound influence. It is also known that absorption or diffusion occurs much more rapidly along grain were and in other deformed regions. Thus an effective sorption experiment must utilize a strain-free and clean surface, or at least a clearly defined and reproducible surface state. A mechanically polished surface is in a highly deformed17-l9 state. Because the degree of this deformation is uncertain, it is clear that for most experimental purposes a strain-free (i.e., etched, chemically polished, or electropolished) surface is desirable. Although adsorbed gas molecules on metallic surfaces are unavoidable even in the highest vacuum,20 oxide films can in some cases be removed by suitable vacuum annealing. Electrolytically polished and annealed surfaces, being relatively without strain, smooth and free of bulk oxides, were considered adequate for the present sorption experiments. Measurement of the surface composition of a solid-vapor couple presents a unique problem. Since experiments to determine the approach to equilibrium of the surface composition must be performed at temperatures where diffusion is very slow, solute penetration is so small that conventional analytical methods are unsuitable. An optical reflectivity method utilizing a polarization spectroscope was employed because of the relatively small penetration (~200A) of visible light in metals. By this method, elliptically polarized light reflected from the metal surface was analyzed and compared with that reflected from samples of known composition. The a phase of the copper-zinc system was

Jan 1, 1962

By Charles S. Barrett

NUMEROUS determinations1-7 of the tex-ture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Wever1 and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the roll-ing direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist.

Jan 1, 1940

By E. M. Tory, P. T. Shannon

An analysis of batch and continuous thickening in terms of the movement of planes of constant concentration (i.e. continuity waves) is presented. Use of solids flux as a primary variable greatly facilitates the analysis and clarifies the relationship between batch and continuous thickening. An "ideal" slurry is defined as one whose settling rate is a function only of the local solids concentration. An analysis of continuous thickening of this ideal slurry in an ideal thickener explains many aspects of the steady — and unsteady — state behavior of real slurries, such as the main features of a thickener's "solids profile" (including the break attributed to rake action), the sudden appearance at abnormally high feed rates of a zone of constant concentration and the velocity with which it rises, and the effect of detention time at constant weight of sludge per unit area. Where deviations exist, they are explained in terms of the batch settling behavior of real slurries. The purpose of this paper is to interpret continuous thickening phenomena in terms of batch settling behavior. Both types of thickening may be considered as the process of propagating concentration changes, due to the downward movement of the solids, from the bottom of the settling vessel upward through the slurry.' These concentration changes may be either finite or infinitesimal as in the case of the propagation of a continuous concentration gradient. The slurry itself may be moving downward as in the case of continuous thickening. The downward velocity of the slurry may be such that the concentration changes being propagated up from below remain stationary relative to the thickener walls. This is the case for steady-state thickening. It seems appropriate to analyze continuous thickening in terms of the movement of planes of constant concentration. This has already been done for batch settling."3 Although our main interest is in real slurries, there are certain aspects of both types of settling which can be deduced from a theoretical analysis of highly idealized systems. To this end, an "ideal slurry" is defined as one for which the dimensionless settling rate at any point is a function only of the local solids concentration.1,2 An "ideal thickener" is one in which there is no radial variation in either the solids concentration or in the downward component of slurry velocity. The underflow outlet is a point sink. It is to be expected that the behavior of non-ideal systems will deviate in some measure from theoretical results. However, the same characteristics which cause deviations in continuous thickening should be evident in batch settling, permitting a rational explanation of the former in terms of the latter. PREDICTED RESULTS FOR AN IDEAL SLURRY IN AN IDEAL CONTINUOUS THICKENER General Theory: In continuous thickening, the downward solids flux (mass/area-time) relative to the thickener, G, results from two different

Jan 1, 1967

By Rodney L. Stone, David S. Cahn

As part of an over-all laboratory and plant test program to determine mixing ad other techniques for a more economic use of bentonite as an iron ore pellet binder, a settling test for measuring the bentonite content within a pellet or a batch of pellets has been developed. Through this test, it has been shown that dry fracture load is directly proportional to bentonite content in batches of pellets, but inversely propor tional to bentonite content in individual pellets of the same batch. This apparent paradox is explained by a negative correlation between a pellet's size and its bentonite content and the fact that large pellets can withstand a higher fracture load than small pellets. In past attempts to characterize green and dry iron ore pellets, the authors found large variations in the results of strength tests on closely sized pellets from the same batch.' Reasons advanced for such variations in the quality of pellets in which the binder is bentonite were the presence of internal flaws and the nonuniform distribution of the binder. Even when resulting pellet strength is good, there is still the question of whether the same strength could have been attained through a more effective use of a smaller amount of bentonite. The authors' own and other studies 2-3 have pointed out the strong dependence of pellet strength on the degree of "mixedness" of the iron ore concentrate and the bentonite binder. However, before such a relationship could serve as a guide for the development of better mixing techniques and the associated economy of

Jan 1, 1969

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. 1). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944

By Eugene F. Poncelet

Glass squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. Experimental Procedure Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. I). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2½-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through'' of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1947

By Eugene F. Poncelet

Glass squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. Experimental Procedure Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. I). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2½-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through'' of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1947

By J. Szekely, J. W. Evans

A formulation is given for radiant heat loss from the surface of molten steel held in a ladle and numerical solutions are presented for the resultant integrodif-ferential equations. The results are shown on plots of the net rate of heat loss against time, with the geometlry, emissivities, thermal properties of the walls, and Preheat as parameters. It was found that the rate of the vadiant heat loss from the exposed metal surface was comparable to the conductive losses from the Portion of the metal in direct contact with the walls. The radiant heat loss was markedly affected by the geometry and by the thermal properties of the walls the net radiant heat loss from the steel could be drastically reduced by providing a top cover and also by the provision of preheat. The results of this work are thought to be relevant to heat loss calculatious concerned with vacuum degassing and with operatzons in which molten metals are held in ladles. WhEN molten steel is held or transferred in ladles heat losses inevitably occur. The accurate assessment of these heat losses is of importance in process design considerations, as the temperature of the metal may have to meet rigid specifications in certain stages of the processing sequence. As shown in Fig. 1, the principal mechanisms responsible for heat loss are: i) Conduction into the walls and ii) Thermal radation from the top metal surface (possibly augmented by natural convection) The conductive heat loss may be readily calculated as much information is available in the literature on both the general theory1'' and on its particular applications to ladle heat loss calculations. Evaluation of the radiant component of the heat loss is less straight-forward. In two recent papers it has been shown that the presence of a slag layer 2 to 3 in. thick would prevent any significant heat loss for periods up to an hour,5'" however, should bare metal be exposed, constituting the radiant surface, substantial heat losses could occur. This latter case is of considerable practical interest in various degassing operations and in the vacuum processing of certain specialty steels, where the top surface of the metal is not covered by a protective slag layer. Under these conditions a substantial radiant flux is emitted by the top metal surface; part of this flux leaves the system, part of it falls in the ladle walls. The radiant flux incident on the ladle walls is in part absorbed and conducted away, and in part reflected and re radiated. The purpose of the paper is to present a general formulation of the problem, the resultant solution of which should enable computation of the net radiant heat loss from the metal surface. The principal variables, the effect of which will be investigated, include initial metal temperature, geometry, thermal and radiative properties of the wall, and various modes of preheat. FORMULATION Consider a cylindrical enclosure, shown in Fig. 2, with a diameter D, height H, and wall thickness W, the cover at the top of the cylinder having a wall thickness L. If the temperature of the base (representing the top surface of the metal) is kept constant, say, Tb, the problem is to calculate the net rate of heat loss from the base as a function of time, geometry, the initial temperature distribution, and the thermal properties of the system. As customary, the formulation will consist of the mathematical statement of the conservation of thermal energy within the system.

Jan 1, 1970

By T. S. Lundy, J. Askill

J. Askill and T. S. Lundy (Oak Ridge National Laboratory)—Moore has proposed a simple correlation between the activation energy for solute diffusion in fee metals and the atomic volume of the diffusing species using both tracer and chemical-diffusion data. The first point we wish to make is that it is wrong to attempt such correlations without separating the two types of data. Activation energies obtained using tracer techniques cannot, in general, be directly compared with those obtained from chemical-diffusion experiments. A knowledge of the variations of chemical potentials with composition is necessary and chemical-diffusion data must be corrected for such variations, even for dilute alloys, before a comparison is possible. Secondly, for nickel, iron, aluminum, and lead, Moore neglected a number of recently published works, e.g., Al26 and Mn54 in aluminum,46 cr51 in nickel,47 and Fe55 in iron.48 These and others should have been used. If one considers only the tracer diffusion data, there is left no simple correlation of the type proposed by Moore. For example, in the case of solute diffusion in aluminum the only reliable tracer data listed by Moore are for zinc and aluminum. The nickel, cobalt, and iron data of Agarwala49 are representative of near-surface diffusion-not bulk diffusion. In conclusion we suggest that for tracer diffusion data in these fee metals there is no justification for proposing any simple correlation of activation energy with atomic volume using the limited data that are presently available. R. H. Moore (author's reply)—The writer has proposed a simple correlation which is useful in estimating the internal consistency of diffusion data. The accuracy of the correlation is, of course, a function of the number of data available. Lundy and Askill take issue with the writer's decision to include data for the systems: nickel, iron, aluminum, and lead, taking the view that the data are insufficient to establish the correlation. The writer agrees that the data are insufficient and has cau- tioned the reader that the correlation is tentative in these instances. Inclusion of these systems is justified by the interesting trends the correlation reveals. For example, the distinction between interstitial and substitutional diffusion may be clearly established, Figs. 4 and 6, and the behavior of transition elements and nontransition elements is indicated to parallel the behavior illustrated by the silver and copper systems. Lundy and Askill have singled out the aluminum system for special criticism. The writer chose to discuss the data for diffusion of iron, nickel, and cobalt in aluminum in the terms used by the original authors9 and has included the comments of Balluffi.l0 The writer did not intend the reader to conclude that data for these elements should correlate with data for the nontransition elements as Lundy and Askill have evidently assumed. Iron, nickel, and cobalt form intermetallic compounds with aluminum, so the activity coefficients of these elements may be expected to deviate markedly from unity. This may account for the low frequency factors observed by Hirano.9 The nontransition elements, on the other hand, yield relatively simple phase diagrams with no evidence for intermetallic compound formation as in the case of iron, nickel, and cobalt. In dilute solution, Henry's law should be closely obeyed, the activity coefficients should not deviate markedly from unity, and the effect on the activation energy should not be large. The accuracy of the correlation applied to these systems will improve as the data is extended. It does not seem unreasonable to conclude that its extension should be encouraged.

Jan 1, 1965

By Frank A. Crossley

The work described has one serious shortcoming: grain size was not monitored during heat up to the temperature (1675°F) of isothermal anneal. The chief obstacles to p grain growth in titanium a-ß structures are the a grains. Heating a structure such as that shown in Fig. 1 to a temperature close to ß transus causes dissolution of a grains in order to adjust the a/ß ratio, compare Figs. 1 and 2. During this process there is a concomitant growth of the ß grains—otherwise ß grains would have to be nucleated in order to adjust the a/ß ratio. When the annealing temperature is reached the a/ß ratio stabilizes and this initial phase of ß grain growth ceases. After an incubation period growth resumes as described. Some 0 grain boundaries can be clearly seen in Fig. 1. (Skilled metallography commonly produces photomicrographs which show more structural detail than direct observation.) These boundaries suggest that the average ß grain size is approximately 0.002

Jan 1, 1970

By R. Stickler, A. Vinckier

An optical and electron microscope study was made on a commercial 302 stainless steel heat treated for massive carbide precipitation. Convincirg evidence was obtained that the grain boundary precipitate does not grow away from the grain boundary into the matrix, but grows as a network of large thin dendrites in between the grains. IN austenitic stainless steels the carbon in supersaturated solution precipitates when the steel is heated in the temperature range 450" to 1000°C. During such heat treatments the chromium-rich carbide occurs primarily at the grain boundaries and has adverse effects on the corrosion resistance and low-temperature ductility of the material. It has been shown that the morphology of the precipitated particles differs widely depending on the time and temperature of the heat treatment, the nature of the boundary, the misfit between the grains, and so forth.1"5 It was assumed by Mahla et al.,' Streicher,' and Mc Nutt' that the carbide particles which nucleate in the grain boundary grow in various geometric or dendritic forms away from the boundary into the matrix. However, Kinzel,' Hatwell et a, and Plateau et aL4 found that the particles nucleate in the grain boundary and grow as a network of thin dendrites in the grain boundary interface. We have made a comprehensive studyg of the precipitation occurring in a commercial 302 austenitic stainless steel heat treated for times ranging from 0.15 to 1500 hr at various temperatures from 480" to 1065"~. This study was made to elucidate the influence of heat treatments on both the mechanical and the corrosion properties of this steel. Part of this investigation which is pertinent to the morphology of the grain boundary carbides referred to above is separately reported here. We found that the particles which nucleated in the boundaries grew in the interface of these boundaries, thus supporting the viewpoints of Kinzel,' Hatwell et al.,3 and Plateau et al.4 Furthermore, when carbide particles nucleated in the matrix very close to the boundaries, they possessed a morphology distinctively different from the particles growing in the grain boundaries. MATERIAL A study of metallographic samples and of fracture surfaces of a 302 stainless steel is reported in this paper. The composition and heat treatments are listed in Table I. Polished and etched samples were examined und813r the optical microscope, and carbon extraction replicas of etched micrographic samples and various fracture surfaces3'8'9 were examined under the electron microscope. RESULTS AND DISCUSSION A representative optical micrograph of the 302 steel, condition A, is shown in Fig. l(a). Particles can be seen on the grain boundaries but no traces can be found of particles which grow from the grain boundaries into the matrix. A carbon extraction replica of this sample shows numerous large thin dendrites, Fig. l(b). The lateral dimension of such carbide particles vary up to 100 p, and their thickness estimated from the amoun! of electron penetration i:; between 500 and 1000A. Such large dendrites are extracted from almost all grain boundaries and, if they had grown into the grains, they would definitely be revealed by etching traces in the matrix, Fig. l(a). The reason why these large dendrites on the extraction replica appear to be grown into the grain is due to the mechanism of the extraction replica process. Thus, these dendrites are supported by the carbon replica film only at the edges originally along the grain boundary trace A-A, Fig. l(b), in the polished metal section and have subsequently fallen over onto the carbon replica film during handling. Although such dendrites generally fall only to one particular side of the grain boundary trace, one finds occasionally that parts of a dendrite have fallen to both sides, as shown in Fig. l(b). Further evidence for the growth of carbide in the grain boundary can be obtained from the appearance of fracture surfaces. A small impact specimen of the 302 steel, condition A, was broken at liquid nitrogen temperature. The fracture path follows the

Jan 1, 1962