Search Documents

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin: The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most promising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestetn Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1947

By W. O. Crosby

INTRODUCTION. THE crystalline belt of the Atlantic Seaboard, south of New York, attains its maximum breadth of 220 miles on the northern border of North Carolina; and in this State it is most widely characterized by the occurrence of gold in workable deposits. Half a dozen auriferous belts have been recognized by Nitze and Hanna.1 These are, in the main, coincident in position and trend with the NE.-SW. zones of metamorphic slates and schists, which, more than any other feature, give character to the geological map of North Carolina. The central gold-belts, accompanying the main zone of slates and associated igneous rocks, are much the more important and persistent, and may be regarded as continuous northward across Virginia and southward into South Carolina. Tile eastern belt, on the other band, is the shortest and, economically, one of the least important. Its extreme length does not exceed 25 miles, the narrow band of slaty rocks to which it belongs passing, both NE. and SW., beneath the coastal-plain formations. But, although limited in area and production, this belt is, perhaps, comparable with the central belts or any part of the sea-board crystallines in the variety of conditions under which the gold occurs. It lies chiefly in the NE. part of Franklin county and the NW. part of Nash county, on the watershed of Fishing creek and other tributaries of Tar river. The elevation is between 400 and 500 ft. ; and the Tertiary peneplain has here an exceptionally perfect development, the reliefs separating the slightly incised stream-courses consisting of broad, flat-topped peneplain remnants, bounded by gentle lateral slopes.

Mar 1, 1908

By W. R. Hibbard

Although extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110) , [111] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampton5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr in a standard mer-curous nitrate test. Edmunds12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wasserman11 reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. Preparation OF Specimens Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5, 10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. Determination of Pole Figures A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pet nitric acid to 0.0015 in. thickness and (111) pole figures were determined using copper K-alpha radiation in the manner described by Brick.' The three general types of pole figures

Jan 1, 1949

By W. R. Hibbard

Although extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110) , [111] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampton5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr in a standard mer-curous nitrate test. Edmunds12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wasserman11 reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. Preparation OF Specimens Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5, 10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. Determination of Pole Figures A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pet nitric acid to 0.0015 in. thickness and (111) pole figures were determined using copper K-alpha radiation in the manner described by Brick.' The three general types of pole figures

Jan 1, 1949

By D. S. Tomalin, D. F. Stein

The effect of reducing oxygen to low concentrations on the fracture of high-purity iron single crystals has been examined at 78° and 20°K. It is found that iron single crystals grown by the strain-anneal method usually contain a few occluded grain boundaries which may become embittled in the presence of oxygen, thereby nucleating cleavage fractures. High purity with respect to interstitial elements was found to inhibit twinning and evidence is presented for an orientation dependence of the resolved yield stress. Deformation occurred by slip rather than twinning at both temperatures of testing with elongations of as much as 9 pct at 20°K. THE fracture properties of iron single crystals have been observedl-3 to be a function of temperature, orientation, and purity. Allen, Hopkins, and McLennan1 demonstrated that at 78°K iron single crystals became increasingly brittle as the tensile axis approached the (001) pole of the stereographic unit triangle. Iron crystals with the tension axis near a (001) pole were completely brittle and orientations near the (011)-(111) boundary were very ductile, achieving a 100 pct reduction in area prior to fracture. Later work of Biggs and pratt2 and of Edmondson3 demonstrated that by reducing the carbon content of the single crystals the transition between brittle and ductile failure at 78°K could be shifted to orientations nearer the (001) pole. Ed-mondson went further and pointed out that any mechanism which tended to increase the yield strength of the iron (i.e., carbon addition, pre-strain) also increased the tendency for brittle behavior at 78°K. Thus by a reduction of carbon content Biggs and Pratt were able to obtain ductile behavior to within 20 deg of the (001) pole, and Ed-mondson was able to obtain ductile behavior to within 26 deg of the (001) pole. Edmondson's material had a total interstitial content (carbon, oxygen, and nitrogen) of approximately 60 ppm and, although Biggs and Pratt reported no analysis, indications were that their iron contained comparable impurities. Stein, Low, and seybolt4 purified iron single crystals to a total carbon, oxygen, and nitrogen content of approximately 20 ppm. They observed a lowering of the yield stress with this increased purity, and thus one might have expected an observation of increased ductility. Although they tested specimens of orientations which the previous workers had indicated should be ductile, the crystals failed at a 78°K in a brittle manner with little elongation. Stein noted,' however, that about 90 pet of the failures could be traced in origin to occluded grains. Allen et al.1 and Edmondson3 do not report examination of their cleavage surfaces, but Biggs and pratt2 reported that microscopic examination of the cleavage surfaces of many of their specimens revealed the presence of small occluded grains. Honda and cohen6 and Keh7 have also observed the initiation of fracture at occluded grains in iron single crystals. Therefore, the additional complication of occluded grains must be considered in studying the properties of iron single crystals and the origin of fractures determined if the ductility exhibited by the crystals is to be considered meaningful. Various investigators8-12 have studied the effects of impurities on grain boundaries in high-purity polycrystalline iron. Rees and Hopkins10 showed that the addition of oxygen to low-carbon (0.002 pet) iron weakened the grain boundaries, causing a shift from transcrystalline to intercrystalline fracture and a progressive decrease on the brittle-fracture stress with increasing oxygen content. In addition, it has been shown by Low and Feustel11 that the addition of carbon to polycrystalline iron containing oxygen eliminated grain boundary brittleness. Thus, oxygen can embrittle grain boundaries in high-purity polycrystalline iron, but the addition of an appropriate amount of carbon can eliminate the oxygen-induced brittleness. The oxygen content (19 ppm) of the iron "single crystals" employed by Stein el al. was large enough to suspect impurity effects at the occluded grain boundaries. Allen et al.1 Biggs and pratt,2 and Edmondson3 may have masked any occluded grain problem in their specimens considering the relatively high carbon levels they employed. stein13 demonstrated that the addition of as little as 0.9 ppm C to previously purified (less than 5 x 10-3 ppm C) "single crystals" would increase the elongation from a few percent to more than 20 pet at 78°K and the fracture was not associated with grade boundary initiation.

Jan 1, 1965

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

By A. J. de Witte

It has been observed that upon invasion of a sand containing oil or gas and connate water by mud filtrate the hydrocarbons are more rapidly flushed by the filtrate than is the connate water.' In time, it appears that the following displacement pattern emerges: oil (or gas) is being swept ahead by connate water which, in turn, is pushed by invading fluid. Eventually the connate water may have "banked up" sufficiently to form a zone of appreciable thickness leading the invading front. In the extreme case, Fig. 1 shows how the situation will develop.' Immediately adjacent to the borehole (radius r) there is a zone, the invaded zone proper, where the connate water has been flushed out completely and which contains only residual oil or gas and mud filtrate. This zone (extending out to a radius ri) grades more or less abruptly into the next (thickness A), which contains only residual hydrocarbon and connate water. Beyond it, again more or less sharply bounded, extends the virgin formation with the original interstitial water saturation Sw. The various saturations are indicated in Fig. 1. The three zones generally will be marked by resistivity contrasts owing to their different fluid contents. As the connate water is usually more saline than the invading fluid, the second zone having a high connate water saturation forms a concentric cylindrical ring or annulus of low resistivity R, around the borehole.',' It will be referred to as the "low zone." Fig. 1 shows schematically the resistivity profile. It is clear that the phenomenon of a low zone could not occur in invaded water sands. The presence of a low zone, therefore, would be a qualitative indication of a hydrocarbon-bearing formation. Granted that the phenomenon is real, if it were pronounced enough to be detected, one might thereby have a means of locating oil or gas in the ground. This is the aim of the "displacement logging" method.' In any case, the presence of a low resistivity zone will affect the reading of electric logs. Using conventional log interpretation techniques, one must be aware of this and, if necessary, correct for it. Whether correction or detection should be the goal will depend primarily on the magnitude of the effect. The type of log which is likely to be affected most is the induction log. The current pattern of an induction log is concentric with the borehole. Any concentric ring of low resistivity, therefore, will tend to become crowded by current lines. This zone of maximum current density will obscure the relative contributions to the current conduction by other portions of a bed making, for instance, the contribution of the virgin formation less significant and thus detracting from the value or the induction log as an R, reading device. The present note is intended to ascertain the maximum possible effect of a low zone in the extreme case portrayed by Fig. 1 on three commercially available types of induction logs, sc., 5 FF 27, 5 FF 40 and 3 F 60. Type 5 FF 27 or 5 PF 40 is currently run in conjunction with a 16 in. normal and SP log. This combination is gradually replacing the regular electric survey (two normals and one lateral) as a standard log in many areas. On the basis of the scheme of Fig. 1 (sharp boundaries between successive zones), the thickness of the low zone may be computed for various amounts of infiltration measured by the ratio of invaded zone diameter to hole diameter D,/d. Referring to Fig. 1, we can set up a material balance for the water displaced from the invaded zone proper and the water present in the low zone. The volume of connate water displaced from invaded zone upon flushing by mud filtrate is: V1 = e p (r2 - r2) ? Sw . where c = bed thickness ? = porosity Su, = original connate water satu-ration. The volume of water finally accu-mulated in the low zone is: Vz = e p [(r1 -?)2 - r2 4] ? Sw . where SW1 = 1 — Sor = "water" saturation in the invaded and low zones both. The volume of water originally present in the low zone is:

Jan 1, 1958

ENGINEERS AVAILABLE (Under this Beading will lie published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member,, technical graduate, aged 38, 14 years' experience in engineering, exploration, and management of copper, pyrite, and large iron mines, safety work, professor of mining in large university. Married. Open for position after June 10. No. 205. Member, graduate engineer, aged 44, with over 20 years' experience in connection with large coal and coke operations in different parts of the country, desires position as general superintendent of large coal company, or will take an interest with the management in a smaller company. No. 206.

Jan 5, 1915

By E. T. Turkdogan, L. J. Martonik, R. J. Fruehan

Electrochemical measuretnents of the solid oxide electrolyte galvanic cells CY-Cr2O3 I ZrO2 (CaO) 1 O (in Fe alloy) CY-Cr2O3 I Tho2 (Y2O3)I O en Fe alloy) have been made at 1600°C (2912°F) in order to test the Performance of such cells at liquid steel temperatures. The oxygen pvobe (cell) consists of a disk of ZrO2 (CaO) or Tho2 (Y2O3) electrolyte fused at one end of a silica tube filled with a mixture of Cr-Cr2O3 which is the reference electrode. Upon immersion in liquid steel, the electromotive force readings achieve a steady value within a few seconds, and remain steady for 30 win or more. The perforwzance of the probes has been tested using Fe-O, Fe-Si-O, Fe-Cr-O, Fe-V-O, and Fe-Al-O alloys; the oxygen contents of liquid steel derived from the measured electromotive forces are in satisfactory agreement with those determined by arulysis. Use of the probe in the deoxi-datiorz of steel, in laboratory experiments, is discussed. The results indicate that there is insignificant electronic conductivity in ZrO2(CuO) at oxygen activities down to those corresponding to 10 ppm in steel. At lower oxygen activities, probes tipped with ThOn (Y2O3) disks perform satisfactorily at oxygen activities down to 1 ppm O or less. THE key to the control of deoxidation of steel is a sensing device to measure rapidly the concentration of oxygen in liquid steel in the furnace, ladle or tun-dish at any desired stage of deoxidation. The analysis of the cast steel by the neutron-activation or vacuum-fusion method gives total oxygen as oxide and silicate inclusions. This analysis is important for guidance to steel cleanliness; however, such a postmortem is of little value in the control of deoxidation of liquid steel. At the General Meeting of the American Iron and Steel Institute in New York, 1968, Turkdogan and Fruehan' presented a paper on the preliminary results of the work done in this laboratory on rapid determination of oxygen in steel by an oxygen probe. Details of the work done in this laboratory leading to the development of a galvanic cell for the determination of oxygen in liquid steel, and the results of the tests made are given in this paper. It was through Wagner's contributions, since the early Thirties, to the physical chemistry of semiconductors in general that it ultimately became possible to construct galvanic cells for application at high temperatures. In 1957, Kiukkola and wagner2 successfully demonstrated the use of several solid electrolytes in measuring the free energies of several chemical reactions, in particular, the use of lime-stabilized zir-conia in high-temperature oxidation reactions. Starting 7 years later, a number of papers appeared in the technical literature3-' demonstrating possible applicability of galvanic cells for the determination of oxygen in liquid steel. In the earliest work, Japanese investigators3j4 experimented with various types of reference electrodes, e.g., graphite-saturated liquid iron at 1 atm CO or Ni-NiO mixtures; the results obtained, though promising, were not of sufficient accuracy. Except for the work of Baker and West,6 all other investigators5,7,8 showed that ZrO2(CaO) electrolyte could be used for this purpose. The main part of the galvanic cell used by Fischer and ~ckermann' and by schwerdtfeger7 (the latter work was done in this laboratory), consisted of a ZrO2(CaO) tube, -1 cm ID, closed at one end, with a platinum contact wire fixed mechanically inside the closed end. The tube was flushed with a gas of known oxygen partial pressure, e.g., air, CO-CO2 or H2-CO2 mixtures; gas along with the platinum lead wire served as the reference electrode. The oxygen contents derived from measured electromotive forces agreed reasonably well with the oxygen contents determined by vacuum-fusion analysis. It is evident from recent investigations that the electromotive force technique using a solid oxide electrolyte is fundamentally well suited for the determination of oxygen in liquid steel. However, it is equally clear that the cell arrangement of the type as commonly used is in need of considerable improvement, as it exhibits several shortcomings for industrial and even laboratory use. 1) Because of its size, the zirconia tube, though stabilized, has a poor resistance to thermal shock. 2) Fine pores and microcracks, which are invariably present in zirconia tubes, are detrimental to the satisfactory operation of the cell, particularly when gas reference electrodes are used. 3) Air or carbon dioxide reference electrodes give rise to high electromotive force readings; as a result, the determination of oxygen in steel becomes less accurate. For higher accuracy, the oxygen partial pressure of the reference electrode should be in the range similar to that of oxygen in steel. 4) Even in laboratory experiments, difficulties are experienced when flushing the tube with gases and maintaining the proper gas flow rate. Fischer and Ackermann,' who used air as the reference electrode, reported that when the flow rate was too low, furnace gases would leak into the electrolyte tube, therefore lowering the oxygen potential and measured electromotive force. The required flow rate in order to avoid leakage depended on the tightness of the electrolyte tube which varied with different tubes, thus making it difficult to predict in advance the required flow rate. However, if the flow rate is too high the inside wall of the electrolyte tube would be cooler than the wall

Jan 1, 1970

By J. N. Ong

The oxidation of tantalum is assumed to occur by four simultaneous first-order chain reactions; solution of oxygen in the metal, nucleation and growth of a suboxide phase at the metal surface and two phase boundary processes which give rise to two different modifications of Ta2O5. A rate equation is then formulated which accounts for all principal details of oxidation behavior, unifies and correlatss the results of the principal investigations, and expresses the rate as a function of pressure, temperature, and time. For purposes of practical application, the expressions: may be used below and above 700T respectively to determine the regression rate of tantalum in cm per hr, where T is to be expressed in "K and P in atmospheres pressure of oxygm. The equations will reproduce within a factor of two all reported experimental rates in the temperature range 475" to 1400°C and pressure range 0.000026 to 40.8 atm 0. 1 HE oxidation kinetics of tantalum have been investigated thoroughly in the temperature range 50" to 1400 and pressure range 1.32 x l0-' to 40.8 atm pressure of 0,and as a result, the principal features of the oxidation of tantalum are known and have been described in considerable detail. The exposition of the characteristics of the behavior of tantalum in oxygen has been largely descriptive, with considerable attention being devoted to elucidating the structure, composition, and morphology of the resulting oxide products. The weight change vs time results have usually been reported graphically. With the exception of the linear rate below 700 C and the process of diffusion of interstitial oxygen into the metal,6'9 no effort has been made to characterize the reaction rates in functional form. It is the purpose of this paper to demonstrate that when the fundamental principles of chemical kinetics are rigorously followed, the results of the principal investigations will be correlated and unified and the oxidation rale may be expressed as an analytic function of pressure, temperature, and time. In addition to accounting for the temperature and pressure dependency of the oxidation rate, the following minor features will be accounted for as a result of the basic analysis: the initial period of nonline-arity in rate at low temperatures, which decreases with increasing temperature;3'5'7 the rate vs temperature cusps obtained at constant pressure"5 the concentration gradient of oxygen interstitially dissolved in the metal.5'7 The analysis will also be consistent with the overall chemistry of reaction and with all visual, microscopic, and X-ray observations. DEVELOPMENT OF RATE EQUATION As a fundamental basis for the treatment of metal-oxygen reaction kinetics, it will be regarded that the rate of reaction is determined by the concentration and not the activity or chemical potential. It is further assumed that all metal-oxygen reactions are first order complex chain reactions" whose rate is dependent on the concentration of an intermediate species which is a complex function of the oxygen concentration, or oxygen pressure, only. The basic rate equation is therefore: is the weight of oxygen consumed by the reaction, A is that portion of the area of the metal over which the reaction is occurring (cm2), t the time (sec), kf the rate constant for forward reaction, C the intermediate species concentration and f '([Oz]) and f (Po,) are complex functions of oxygen concentration and Oxygen pressure respectively. Reverse reactions may usually be neglected in metal-oxygen systems since a large negative free energy generally accompanies these reactions. Eq. [I] takes different forms when the rate of reaction is controlled by diffusion into or through a phase or at a phase boundary. For diffusion into the metal phase, the rate is given by1' Di is the diffusion coefficient of species diffusing into the metal phase (cm2/sec), and Q is the corre-

Jan 1, 1962

By J. L. Gillson

The word "other" in paragraph 4, line 11, column 1, page 205, should read "over;" the correct version of reason 2, this paragraph, is: 'L. . . 2) to evaluate the usefulness of certain geo-chemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and over veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; ...9 On page 206, in the top left hand corner of Fig. 1 (in the area bounded by 47°35' and 116°10), the reference to Fig. 3 is incorrect. The area of Pine Creek, South Fork Coeur d'Alene River, and portion of Big Creek (the area which includes, from left to right, Kingston, Pinehurst, Smelterville, and Kellogg) should be identified as that of Fig. 2A. The headings for columns 1, 3, and 4, Tables I and 11, page 209, column 2, were reversed when the paper was printed. The corrected tables are:

Jan 1, 1961

By Lawrence F. Rooney

One of Edgar Allan Poe's stories that haunts my subconscious is the Masque of the Red Death. These days, whenever I join a group like this, especially during the cocktail parties, I see myself and others as those mythical swingers seemingly isolated from the plague. The world, but this country especially, has had a ball plundering, spending, and wasting its natural resources for 100 years. And, as in days of yore, it is fitting that we end this ball with spectacular fireworks: trips to the moon, so that our grandchildren, huddled in their caves along the Ohio, will better understand how it all began.

Jan 1, 1970

LOCAL COMMITTEE OF ARRANGEMENTS. Major J. W. Powell, Chairman; F. P. Dewey. Secretary; S. F. Emmons, A. S. Hewitt, J. P- Hilgard, Charles Knap, and F. W. Taylor. THE opening session was held in the hall of the new National Museum, on Tuesday evening, February 21st. President Metcalf introduced General W. T. Sherman, one of the Regents of the Smithsonian Institution, who read the following address: ADDRESS OF GENERAL SHERMAN. MR. PRESIDENT AND GENTLEMEN : I have been invited to meet you here this evening to extend to you the cordial greeting of the regents of the Smithsonian Institution, and to assure you that they are most happy to have it in their power to place at your disposal this beautiful hall, dedicated to science and art. This National Museum is the property of the United States, of which the regents of the Smithsonian are simply the custodians, and the board has delegated to its secretary, Professor Baird, the right to extend its use to the National Academy of Sciences and like kindred societies, among which we are glad to class the Institute of Mining Engineers. It is eminently fit that you should meet here at this, the nation's capital, under a roof partly your own, devoted to natural sciences, and in the shadow of the Smithsonian, founded for the exclusive purpose of collecting and diffusing knowledge among men. Of all the workers employed on earth no single class seem to me more worthy the respect of their fellows than those who seek beneath the surface for the useful minerals and metals which contribute so largely to the wealth and comfort of mankind. In no branch of human industry does intelligence come so immediately in contact with labor. To the mining engineer chemistry, mineralogy, and geology are as reading, writing, and arithmetic to the merchant;

Jan 1, 1882

By G. M. Schwartz, J. N. Gundersen

Utilization of magnetite-bearing taconite from the great Mesabi range of Minnesota is fast becoming a major industry in the state. The planning and early development stages of taconite processing projects have been de-scribed1-3 and an excellent discussion has appeared recently4 concerning the current mining, crushing, concentrating, and pelletizing techniques of the Reserve Mining Co., whose operations lie entirely within the Eastern Mesabi district. The present paper will deal only with some of the geological aspects of taconite utilization in the district, with emphasis placed upon some of the common mineralogical and textural features of the tacon-ites currently being mined or stripped and how these factors generally affect the potential recovery of the iron from the metamorphosed Biwabik iron-formation. The generalized geologic setting of the Eastern Mesabi district is presented in Fig. 1. The small circles on the geologic map, adapted from Grout and Broderick,3 mark the location of drill holes that were available for inspection during this study through the courtesy of Reserve Mining and Erie Mining Cos. The cores from these holes were divided into stratigraphic units and examined for their mineral content. Typical mineral associations and grain fabrics were also determined from hundreds of thin and polished sections. Available metallurgical tests made it possible to determine the probable response of a given variety of taconite to magnetic concentration. The longitudinal section of Fig. 1, projected along the strike of the iron formation, presents the simple stratigraphy of the area. It also shows the uniformly thick nature of the iron formation members in the district as well as a somewhat abrupt thickening of the formation to the west of the probable fault. The stratigraphy of these precambrian rocks has been described5-' elsewhere and need only be briefly reviewed. Historically, the oldest rocks unit, the Giants Range granite (Algoman) was covered by the Animikie group of sediments (Middle Huronian?), consisting of the Pokegama, Biwabik, and Virginia formations. Outcrops of the Pokegama quartzite are locally distributed along the northern limit of the Biwabik iron formation, but they are too limited to depict on the geologic map of Fig. 1. The effects of the intrusion of several small diabase sills within the Virginia and Biwabik formations are obscure because all of these rocks have been subsequently highly metamorphosed, mainly by the Duluth gabbro. The emplacement of the transgressing Duluth gabbro (Middle Keweenawan) and that of numerous peg-matitic veins in the iron formation8 has resulted in extensive contact and metasomatic metamorphism which has locally reconstituted the previously existing minerals of the Biwabik formation, in large part quartz and magnetite, into a wide variety of silicate mineral assemblages9 that have a profound effect upon the re coverability of the remaining magnetite. The entire region has subsequently been eroded and largely buried beneath Pleistocene glacial deposits. Structurally, the strike of the gently dipping Animikie group generally parallels the elongate outcrop pattern of the Biwabik iron formation on the map of Fig. 1. The Animikie group most commonly dips from 5" to 15" to the south-southeast. In this area, the Duluth gabbro pluton is somewhat sill-like, dipping about 30" to the southeast. Projecting these present structures upward, it seems probable that the gabbro once extended over the underlying Animikie group in the Eastern Mesabi district. SELECTION AND PRESENTATION OF DATA Because of the locally intense metamorphic activity in the district, mineralogical variations within the magnetite-bearing taconites are commonly abrupt, both vertically and laterally. Consequently it is difficult to select a single hole or small group of holes whose cores will be entirely representative of all of the district. Two holes have been selected, however, that in a general way represent mineralogical and textural variations that are likely to be encountered in both the eastern and western parts of the district. These recently drilled holes were chosen for discussion because it was possible to log the core and then to place the sample intervals at stratigraphic boundaries prior to preparation of the core for magnetic tube tests.

Jan 1, 1961

By A. Mitchell, T. Bagshaw

A recent paper by Thomas1 has presented new data on the solubility of hydrogen in solid silver at 1 atm pressure in the temperature range 600° to 963°C. However, no data is reported in the literature on hydrogen solubility in liquid silver. The Sieverts technique which has been described previously2,3 was used in the present work. Charges of approximately 160 g were melted in Morgan "purox" recrystallized alumina crucibles and purified helium was used for the determination of the "hot volume" during each experiment. A chemical analysis of the silver indicates that the impurity content (Cu + Al) is less than 0.02 wt pct. Hydrogen solubility in the temperature range 963° to 1200°C was investigated. The results of three experiments are shown in Table I. Fig. 1 shows an Arrhenius plot of the present work together with the solid-state data of Thomas, Steacie, and johnson,4 Eichenauer et al.,5 and Siegelin et al.6 The following expression has been derived from the Arrhenius plot of the present data: log (solubility of hydrogen, cm3 per 100 g) = 2.154-3512.0/ToK The heat of solution derived from Fig. 1 is 31,150 cal per g mole H2 compared with the value of 33,020 cal per g mole H2 obtained by Thomas and 12,000 cal per g mole H2 obtained from the data of Steacie. It was observed that hydrogen evolution took place when the silver melts were solidified under 1 atm of hydrogen, which would not be expected from an extrapolation of the results of Steacie. Schenck and Lange7 have observed that, for several transition metals at their melting points, the ratio of the hydrogen solubility in the liquid to that in the solid lies in the range 2.1 to 3.1. The present results and those of Thomas are in accord in this respect having a ratio of 2.8. 'C. L. Thomas: Trans. TMS-AIME, 1967 vol. 239, pp. 485-96. 2T. Bagshaw and A. Mitchell: I. Iron Steel Inst., 1966, vol. 204, p. 87. 'M. Weinstein and J. F. Elliott: Trans. TWS-AIME, 1963, vol. 227, p. 382. 'E. W. R. Steacie and F. M. G. Johnson: Proc. Roy. Soc. (London), Ser. A, 1928, vol. 117, pp. 662-79. 'W. Eichenauer et al.: Z. Metallk., 1958, vol. 49, pp. 220-25. 6W. Siegelin et al.: Z. Elektrochem., 1957, vol. 61, pp. 359-66. 'H. Schenck and K. W. Lange: Arch Eisenhuettenw., 1966, vol. 37, no. 9, pp. 739-48.

Jan 1, 1969

By Joseph Singewald

AMONG the genetically interesting iron ores of the United States are those of the St. Francis Mountains near Ironton and Iron Mountain, Missouri. They are specular hematite in porphyry. The Iron Mountain and Shepherd Mountain deposits are generally spoken of as veins and those of Pilot Knob, Cedar Hill, and Russell Mountain as bedded deposits. Iron Mountain has produced nearly 4,000,000 tons of ore and Pilot Knob about 1,500,000 tons. The output of the other three localities has been insignificant. Pilot Knob is no longer worked as an iron mine, but the rock is now being crushed for use as road metal. Iron Mountain has continued as an active producer. In 1927, the property was acquired by the M. A. Hanna Co. and an extensive prospecting and exploration campaign was undertaken, so that the ultimate production of Iron Mountain will doubtless greatly exceed the figures mentioned.

Jan 1, 1929

By B. A. Rogers

The etching effect that is produced on a piece of polished iron or steel when it is heated in hydrogen or in a vacuum seems to have been observed first by Osmond,' who believed that he could distinguish four systems of grain boundaries on a piece of steel which had been heated in hydrogen. In a number of other investigations, samples of pure iron were found, after heating, to have complex networks in which two or three systems of grain boundaries could be detected. It was further noticed that samples that had been polished plane before being placed in the furnace were, after treatment, roughened and undulating over their entire surfaces. From a comparison of the temperature of heat treatment with that of the A3 transformation, it was concluded that the changed appearance of the samples was definitely related to the latter phenomenon. Certain other deductions were made but these are not of importance here and only observations on the appearance of the samples will be reviewed. Ewen2 heated a strip of polished iron in a vacuum in such a way that one end was maintained at a temperature of 1000" C. and the other at 580" C. On the cooler end there was outlined a simple polyhedral network, and at the hotter there appeared the complex systern of lines ant the undulating surface characteristic of iron which has passed through the A3 transformation. He found that in going from the cooler toward thc hotter end the sample maintained much the same character of surface up to the beginning of the transformed area, but that near this region doublc grain boundaries were of frequent occurrence. Rawdon and Scott concluded that the simple type of network brought out by heating a sample of pure iron in a vacuum was of the same type as that developec by ordinary etching methods. They also confirmed the observations of

Jan 1, 1929

By M. A. Quader, D. Kuhlmann-Wilsdorf, R. A. Dodd

STACKING fault tetrahedra were first observed in quenched and aged pure gold by Silcox and Hirsch1 and identified as defects originating in the collapse of vacancy discs on {111} planes. It was supposed that sessile loops are the first product of the collapse, and that by a dislocation dissociation/glide sequence these are converted into tetrahedra. Although the tetrahedra can be mechanistically accounted for in this way, recent investigations indicate that their growth occurs by the absorption of individual vacancies on small nuclei involving perhaps as few as six vacancies.2-7 Besides stacking fault tetrahedra, triangular and crystallographic shaped Frank loops, although fewer in number, have always been observed in quenched and aged gold.19798 It is not known definitely whether these loops form from collapsed tetrahedra. The fact that the Frank loops are usually larger than the accompanying tetrahedra might indicate that the loops grow independently by absorbing vacancies, but this does not rule out the possibility of the collapse of tetrahedra into loops under all circumstances. Silcox and Hirsch1 have actually observed under the electron microscope tetrahedra collapsing into loops, probably due to stresses set up by the heating of the specimen by the electron beam. The energy residing in the stacking faults of a tetrahedron is proportional to the square of the edge length, while the energy of a triangular perfect dislocation loop depends on its edge length, L, as const L ln(L/ro). Therefore, beyond some critical size tetrahedra must become unstable with respect to collapse into triangular loops.1,3,8-11 However, it seems that in the absence of strong stresses tetrahedra usually decay by the

Jan 1, 1969

By H. E. Strauss

The time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at IIOO°C. better than did to per cent iridium-platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at IIOO°C. Platinum alloys in their service at high temperatures encounter conditions somewhat similar to those that exist in the usual form of the "time-to-fracture"l test with steel. This paper is intended primarily to present results obtained by a "time-to-fracture" test under conditions approximating actual service for platinum (at the temperature IIOO°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with 10 per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., IOOO°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,' using as heating unit a small, horizontal, platinum-wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life—that is, the time-to-fracture—was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fratture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking Stresses drop very rapidly to a small frat-286

Jan 1, 1943