Search Documents

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and "{2,3,10)" or "(127)". (It is now thought1' that the "{0,1,13)" habit reported for the Fe-Ni-C alloys'' is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove.' The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and tj2 = vi (i = 1, 2, 3), the Kz qd 771 elements are given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics cij Iand cij reduce to the unit tensors 6ij and 6ij so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and 77~ are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963

By W. Joseph Schlitt, Kenneth J. Richards, John D. Prater

Kennecott Minerals Company has developed a leach-hydrolysis route for treating flue dusts from copper smelters The flue dusts are acid leached in an oxygen atmosphere to solubilize copper and fix the arsenic, antimony, and bismuth as stable compounds Copper is recovered by cementation with Iron and the barren solution is recycled Molybdenum and other values may be recovered by modification of the basic flow sheet Results of bench scale and pilot plant tests are discussed in terms of the effect of operating parameters.

Jan 1, 1981

The world's largest steam-driven mine hoist, built by Nordberg Manufacturing Co. a half century ago, has become a major tourist attraction in Michigan's Upper Peninsula. The hoist, designed by company founder Bruno V. Nordberg, is located in the Quincy Mine Number Two, just north of Hancock. Nordberg began construction of the mammoth machine before World War I, but delayed completion until after the war. The hoist became operational in 1920 and continued running until the mine was shut down in 1931.

Jan 9, 1968

By Charles Dorrance

Culm is a general term used in the anthracite regions for many years to denote a mixture of coal, bony coal and impurities which is sent to the refuse-banks. Thus, 35 years ago culm contained the pea and buckwheat sizes of anthracite; but to-day, and as mentioned in this paper, culm is used specifically to denote the material which passes through the smallest screen in the anthracite-breaker. The smallest size of commercial anthracite is known as No. 3 buckwheat, barley, or bird's-eye coal, and is ordinarily made through a round-punched plate having openings & in. in diameter, and over a round-punched plate with openings 3/32 in. or 1/16 in. in diameter. Thus culm will consist of coal, bony coal, slate, gravel, iron pyrite, etc., ranging in size from 3/32 in. down to dust. Other local terms for culm are " slush," " silt," and " dirt." The first experiments towards the utilization of anthracite culm by briquetting, and the first briquetting-work done in this country, were in 1872 at Port Richmond Piers, Philadelphia, Pa., by E. F. Loiseau.1 Clay was used as a binder and the finished briquette was water-proofed with shellac, etc. Excessive cost was given as the reason for discontinuing work at this plant.

Jan 1, 1912

By P. H. Mell

Can the auriferous slate deposits of the Southern mining region ever be successfully worked ? is a question that has been often asked me by persons seeking investments in Southern mines. As the subject is one that has given me much thought during the past few years, I have decided to present my conclusions to the members of the Institute for their consideration. Those who have had the opportunity of exploring the region mentioned above, will readily reall to mind numerous localities, to which their attention was directed by would-be miners, as "rich and desirable properties," in which there were but few quartz seams running in every direction through fine-grained talcose slate. Most of the gold in such formations was always found disseminated through the slate, and but a small percentage contained in the quartz. Such are the deposits I propose to discuss in this paper. Of course there are many excellent quartz mines in the South that are paying the owners good profits, and many more to my knowledge, that are not being worked for obvious reasons. But it is out of the question to suppose that these slate deposits can be practically

Jan 1, 1881

By P. H. Mell

CAN the auriferous slate deposits of the Southern mining region ever be successfully worked? is a question that has been often asked me by persons seeking investments in Southern mines. As the subject is one that has given me much thought during the past few years, I have decided to present my conclusions to the members of the Institute for their consideration. Those who have had the opportunity of exploring the region mentioned above, will readily recall to mind numerous localities, to which their attention was directed by would-be miners, as "rich and desirable properties," in which there were but few quartz seams running in every direction through fine-grained talcose slate. Most of the gold in sued formations was always found disseminated through the slate, and but a small percentage contained in the quartz. Such are the deposits I propose to discuss in this paper. Of course there are many excellent quartz mines in the South that are paying the owners good profits, and many more to my knowledge, that are not being worked for obvious reasons. But it is out of the question to suppose that these slate deposits can be practically

Jan 1, 1881

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By Sherwin F. Kelly

THOUGH the Geophysics Commit- tee limited itself to two sessions this year, both of them marked by a high percentage of absentee authors, even this situation failed to dampen the and or of the ebullient geophysicists, who bandied no small amount of good- humoredlv barbed discussion. Hans Lundherg offered some constructive criticism of last year's report by the Geophysics Education Commit- tee, making a plea for more training in field techniques and less insistence on rigorous theoretical training. Carl Heiland pointed out the necessity of making geophysics and geology courses more attractive in order to draw more students into these fields. Exception was taken to this line of reasoning by Father Macelwane and Sherwin F. Kelly who emphasized the necessity for sound basic training if competent geophysicists were to be turned out. This discussion developed apropos of the report of the Geophysics Education Committee, which had been postponed from the Education Division meetings, but was not read as it was available in mimeographed form. Except for this diversion the morning program fol-

Jan 1, 1944

By Y. C. Liu, G. A. Alers

measurements of the anisotropy in Young's modulus produced in copper by rolling 95 pct reduction in thickness below room temperature have been carried out in order to study the dependence of the texture on rolling temperature. The results clearly show the transition from a copper-type texture to a brass-type texture as the temperature of rolling is lowered. The intermediate textures observed can be described very well as a simple mixture of the two terminal textures. These results cormbined with other texture measurements make possible afresh review of the experimental facts velating to rolling textures in fee metals and, as a consequence, a critical examination of the current theories is presented. PREVIOUS experiments have shown that the transition from the copper- to the brass-type rolling texture is clearly displayed and can be quantitatively analyzed by measurements of the anisotropy of Young's modulus.' Application of this method to the Cu-Zn alloy system showed that the description of the texture transition as a gradual rotation of the grains from the orientation characteristic of the copper texture to the {110}(112) texture of brass2 was inconsistent with the data. Instead, the data suggested that the texture within the transition region could be described as a simple mixture of the two terminal textures.5 Unfortunately, it was difficult to establish this point conclusively because of the inadequacy of corrections for the composition dependence of the single-crystal elastic constants. Since a rigorous establishment of the nature of this texture transition is essential to our understanding of the formation of rolling textures in fee metals, it is clearly important to undertake an investigation in which the composition dependence of the elastic constants would not enter. A suitable composition-independent texture transition is provided by the well-established variation in the rolling texture of copper with rolling temperature. This temperature-dependent texture transformation has been studied by smallman' in several fee alloys and by Müller5 and others"' in copper. They observed that the texture characteristic of copper rolled at room temperature changed to a brass-type texture when the rolling temperature was lowered to 77°K. Although it is not possible to decide unequivocally from the published pole figures whether or not the 77°K rolling texture of copper is entirely of the brass type,' this complication does not affect the main purpose of the present investigation. In addition to establishing the nature of the texture within the transition region, the modulus data should also provide a determination of the temperature at which the transition occurs as well as the temperature range over which the transition extends. This information when combined with the modulus data on Cu-Zn alloys would then provide a considerable body of new information on textures in fee metals. Since these modulus results and the data obtained from pole-figure studies must be internally consistent, it is appropriate to compile a brief summary of the experimental observations based on all available methods rather than on the pole-figure data alone as has been done in the past. The primary purpose of such a summary would be to yield a more precise definition of the experimental facts on the rolling textures of fee metals, and thus greatly facilitate our evaluation of various proposed theories in this field. The final section of this paper is devoted to this compilation of consistent, experimental facts and their application to the various theories. EXPERIMENTAL PROCEDURE Two 18-lb ingots of cathode copper of 99.99 pct purity were induction-melted under a nitrogen atmosphere in a graphite crucible and chill-cast into a steel mold. The ingots were repeatedly cold-rolled and annealed (I hr at 500°C) into slabs about 1 1/8 in. thick. Blocks 3 1/4 in. wide, 2 1/4 in. long, and 1.000 in. thick were machined from each slab. The rolling schedule used was the same as in the previous investigation1 and the final thickness of the sheet was 0.050 in. with a rolling reduction of thickness of 95 pct instead of 97.5 pct as in the previous work.' The compositions and temperatures of the cold baths used for the low-temperature rolling were as shown in Table I. After each pass the rolled strip was immediately immersed in the cold bath for about 1 min or until the bubbling of the bath had subsided. The modulus data were taken within 2 hr after the rolled strip was warmed to room temperature for the first time, so that effects due to recrystallization were minimized. The modulus specimens were in the shape of flat bars, 3 in. long, 4 in. wide, and 0.050 in. thick, cut with their long dimensions oriented at 15-deg intervals between the rolling direction and the transverse direction. The values of Young's modulus were deduced from measurements of the frequency at which these long narrow bars were set into longitudinal, resonant vibration as previously described.9 To excite the mechanical vibrations in the specimen, an electromagnetic drive similar to that employed by Thompson and lass" was used. The maximum in the amplitude of

Jan 1, 1968

By William D. Manly, John Towers, Paul A. Beck

RECENT work on grain growth in high purity aluminum and in a solid solution type alloy of aluminum and magnesium' showed that the isothermal increase of the average grain diameter D with time follows the equation [D = K(to + A)-Eq I] Here [to] is that portion of the total annealing time [t], which is available for grain growth, i.e. the annealing time less the time necessary for complete recrystallization. The parameters A and n depend only on the temperature. A has the dimension of time, and is usually of the same order of magnitude as the time for recrystallization: R. In some instances R may be substituted for A in Eq I. This is the case for example at long periods of annealing or at high temperatures, where both A and R become small in comparison with t. In such instances Eq I is simplified to [D-K-tnEq2] For high purity aluminum the exponent n increases in the ratio of about 1 to 5 in the temperature range of 350° to 600°C. 70-30 brass has been long known to exhibit grain growth of the continuous type, such as occurs in pure metals. For this reason, it was of interest to determine whether grain growth in brass also follows Eq I and 2 as it does in aluminum. Isothermal grain growth data for 70-30 brass were published in recent years by R. S. French2 and by H. L. Walker3 Fig I shows a log D vs. log t plot of French's data, together with the 500, 600 and 100°C data by Walker for 42.8 pct reduction by rolling. In such a log D vs. log t plot Eq 2 corresponds to a straight line with a slope of n. As seen in Fig I, the data of French and the 600°C data of Walker can be represented by straight lines. However, the 500 and 700°C data of Walker give curved lines and the average slope of his 500°C line is very different from the slope of the line representing French's data for the same temperature. Furthermore the curvature of the 700°C line suggests a tendency for grain growth to stop after 8 hr. If confirmed, this would constitute a definite deviation from Eq 2, not explainable on the basis of the specimen thickness effect found in high purity aluminum.1 Walker's specimens were 0.125 in., i.e. 3.18 mm thick, while the deviation occurs at a grain size of approximately 0.4 mm. A further point of divergence arose recently, when J. E. Burke suggested4 on the basis of Walker's data, that, instead of Eq 2, grain growth in 70-30 brass follows the equation [D-D. =K• t,Eq3] Here D, is the grain size as recrystallized at the temperature in question. Although it was possible to show5 that, for pure aluminum, for which isothermal grain growth has been carefully investigated, Eq 3 is incompatible with the experimental facts, the situation remained somewhat obscure with respect to 70-30 brass. In view of the discrepancies between the

Jan 1, 1948

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By J. F. KENP

THE White Knob copper-deposits are situated about three miles south of Mackay, on the Salmon River .branch of the Oregon Short Line Railroad, in Custer county, Idaho. An outline-map of this district is given in Fig. 1. The deposits have been known and spasmodically worked for many years, and a total of over 3.5 miles of tunnels, shafts and other workings has been driven with a view to their development. These extensive excavations have exposed the deposits sufficiently to permit a careful geological examination. The peculiar features which give special interest to this paper are the branching, free-like form of the ore-bodies; the absence of zones of secondary enrichment in the partly oxidized pyritic deposits, and the fact that while the deposits are associated in a general way with the contact of an eruptive rock with limestone, which it penetrates, the garnetization has taken place not in the limestone, as is the usual case, but in the igneous

Mar 1, 1907

By I. Javandel, P. A. Witherspoon

The finite element method was originally developed in the aircraft industry to handle problems of stress distribution in complex airframe configurations. This paper describes how the method can be extended to problems of transient flow in porous media. In this approach, the continuum is replaced by a system of finite elements. By employing the variational principle, one can obtain time dependent solutions for the potential at every point in the system by minimizing a potential energy functional. The theory of the method is reviewed. To demonstrate its validity, nonsteady-state results obtained by the finite clement method are compared with those of typical boundary value problems for which rigorous analytical solutions are available. To demonstrate the power of this approach, solutions for the more complex problem of transient flow in layered systems with crossflow are also presented. The generality of this approach with respect to arbitrary boundary conditions and changes in rock properties provides a new method of handling problems of fluid flow in complex systems. INTRODUCTION Problems of transient flow in porous media often can be handled by the methods of analytical mathematics as long as the geometry or properties of the flow system do not become too complex. When the analytical approach becomes intractable, it is customary to resort to numerical methods, and a great variety of problems have been handled in this manner. One such method relies on the finite difference approach wherein the system is divided into a network of elements, and a finite difference equation for the flow into and out of each element is developed. The solution of the resulting set of equations usually requires a high speed computer. When heterogeneous systems of arbitrary geometry must be considered, however, this approach is sometimes difficult to apply and may require large amounts of computer time. The finite element method is a new approach that avoids these difficulties. It was developed originally in the aircraft industry to provide a refined solution for stress distributions in extremely complex airframe configurations. 27 Clough has recently reviewed the application of the finite element method in the field of structural mechanics.6 The technique has been applied successfully in the stress analysis of many complex structures.l, 27, 28 Recognition that this procedure can be interpreted in terms of variational procedures involving minimizing a potential energy functional7 leads naturally to its extension to other boundary value problems. In the field of heat flow, there recently have been introduced several approximate methods of solution that are based on variational principles.2-4, 17 By employing the variational principle in conjunction with the finite element idealization, a powerful solution technique is now available for determining the potential distribution within complex bodies of arbitrary geometry. In the finite element approximation of solids, the continuum is replaced by a system of elements. An approximate solution for the potential field within each element is assumed, and flux equilibrium equations are developed at a discrete number of points within the network of finite elements. For the case of steady-state heat flow, the technique is completely described by Zienkiewicz and Cheung.33 Since the flow of fluids in porous media is analogous to the flow of heat, Zienkiewicz et al. have employed the finite element method in obtaining steady-state solutions to heterogeneous and anisotropic seepage problems. 34 Taylor and Brown have used this method to investigate steady-state flow problems involving a free surface.25 The work of Gurtin has been instrumental in laying the groundwork for the application of finite element methods to linear initial-value problems.12 As a result, Wilson and Nickell have recently

Jan 1, 1969

RECENTLY, we were asked to name the greatest contribution to progress in mining technology during the past 25 years. Immediately, the introduction of the pneumatic hammer for making blastholes came to mind because it can be credited with speeding the excavation of rock and the elimination of hand drilling. Possibly this answer was so spontaneous because we were working on this "drilling issue" Of MINING ENGINEERING. Present drilling tools have devel¬oped so rapidly, that a great deal of engineering is. required in the selection of bits, steel, and machines for the drilling conditions at each mine. Formerly a modicum of engineering was utilized in selection of equipment for it was purchased from manufacturer preference. With the development of alloy drill steels, tungsten-carbide bits, throwaway bits, and the jackleg drill, mining companies began doing more experimental work before making selections. It is unfortunately true, that each operator must begin at the beginning by doing his own test work before choosing his drilling method, and tools. Some of this work has been done very well-under controlled conditions and obtaining proper data on the variables. Such data should be accumulated from the various mines, tabulated, and published. Such a volume would be of tremendous help to the small operator in selecting equipment and would permit the research departments of the larger companies to formulate some measure of rock drillability and to undertake more specialized research on the different phases of drilling.

Jan 1, 1952

By Jr. J. L. Ryon.

Experimentation with ammonium nitrate-fuel oil mixtures at three underground salt mines revealed its excellent applications at those properties. The author relates the present blasting practice used at these mines by the Intemzational Salt Co. The International Salt Company is presently performing blasting operations with a pneumatically -placed ammonium nitrate-fuel oil mixture at three rock salt mines, and plans its use in the near future at its new Cleveland mine. Use of ammonium nitrate is saving the company approximately $250,000 annually. With rapidly increasing operating expenses and increasing competitive pressure resulting in lower prices, savings such as those realized through the use of ammonium nitrate are vitally important. ORIGINAL INVESTIGATION AND EXPERIMENTAL ACTIVITIES The three mines presently involved are located at Detroit, Mich.; Avery Island, La.; and Retsof, N. Y. Initial experiments were conducted at the Detroit mine where a detailed investigation was carried on to determine the significance of the static electricity factor when blowing ammonium nitrate into drill holes in which millisecond delay electric blasting caps had been placed. Although the information developed at the Detroit mine was passed along to the other mines, each mine independently pursued its own course of inves- tigation. This fact, plus the differing mining conditions, resulted in slightly different operational procedures at each mine. Some of the varying statistical data are shown in Table I, and data common to all three International Salt Company mines are shown in Table 11. BLASTING PROCEDURE AT THE DETROIT MINE This mine has been using the ammonium nitrate-fuel oil mixture for more than two years on a full time production basis and represents the successful detonation of several hundred thousand holes. Results have been excellent and the blasting cost has been reduced many times. The actual operation at Detroit consists of adding the fuel oil to the bags of ammonium nitrate by means of a portable fuel oil tank complete with hose, nozzle, and metering device. The bags of the ammonium nitrate-fuel oil mixture are transported to the working face from the oiling area by means of a jeep-drawn trailer. At the face, the ammonium nitrate is placed on the elevating platform of a powder-load ing rig which consists of a pneumatically-tired, large fork-lift truck with a fully insulated elevating platform constructed on the forks. The placement of the dynamite primer and the pneumatic placement of the ammonium nitrate is a two-man operation. First, one cartridge of the primer is placed in each hole on the line of holes which can be reached from the loading rig platform. The plastic hose is then inserted into the hole and pushes the primer to the back of the hole. The proper charge of ammonium nitrate is then placed in the pneumatic placement machine and,

Jan 1, 1961

By H. I. Aaronson, H. A. Domian

The self-diffusivity of Ag10 has been measured as a function of temperature and composition in AgMg. a CsCl-type intermetallic compound with a substitutional defect structure on both sides of the stoichiometric (50 at. pct Mg) composition. These measurements show that In D increases linearly, and both In Do and Q decrease linearly with deviation from stoichiometry. The slopes of these lines are significantly steeper in magnesium-rich alloys. Equations for the variation of Q with composition have been derived by application of the theory of random walk processes on the assumption that diffusion in compounds of this type takes place by the six-jump cycle mechanism of Huntington, Elcock, and McCombie. The favorable agreement obtained with experiment furnishes fresh support for the correctness of this assumption. A principal result of this treatment is that. although the concentration of vacancies is considerably higher in the silver sublattice than in the magnesium sublattice, the acfivation energies for movement of the magnesium sublattice vacancies are so much lower that these vacancies are responsible for effectively all diffusion of silver in this compound. A tendency for vacancies of both types to be kinetically bound to wrong atoms is also noted. THIS study was undertaken to examine the influence of substitutional defects upon self-diffusion in an intermetallic compound, AgMg, with a CsCl-type crystal structure. The CsCl structure is exception- ally simple. At the equiatomic or stoichiometric composition in a binary alloy, it consists of two interpenetrating simple cubic sublattices, each of which is exclusively populated by the atoms of one species. When atomic size and other factors are favorable, deviations from stoichiometry can be entirely accommodated by the substitution of atoms of the species present in excess of 50 at. pct on the sublattice of the other species on a one-for-one basis. Under this condition, the only vacancies present are those formed by thermal activation. The excess atoms thus incorporated into the sublattice of the minority species may be considered as substitutional defects in this sublattice. Several X-ray studies have shown that the defect structure of AgMg is entirely of the substitutional type on both sides of the stoichiometric composition.1"3 The thermodynamic investigation of Kachi indicates that, aside from a low level of thermal disorder and these constitutional defects, order is maintained to the solidus temperature. This compound is therefore a particularly useful vehicle for a study of the influence of substitutional defects upon diffusion kinetics. Other advantages of AgMg for this purpose include: the broad composition region, as much as approximately 10 at. pct on either side of the stoichiometric (50 at. pct Mg), in which the compound is stable; the comparatively low temperature range of the solidus (820°C and below),5 making diffusion anneals near this range experimentally convenient; the reasonably good machinability of the compound, permitting utilization of the standard sectioning method of radiotracer analysis; and the availability of a good tracer, A for one of the constituent species. While this investigation was in progress, Hagel and westbrooks reported data on the self-diffusion

Jan 1, 1964

The Section on Aerial Geologizing of the American Institute of Mining and Metallurgical Engineers convened on Monday afternoon, Feb. 17, 1936, during the Annual Meeting of the Institute. Mr. Theodore Marvin presided. Chairman Marvin.—We hope to get through with the papers on the program in time so that you can examine the instruments that are displayed here, and also the photographs and air views brought by the Fairchild people. This is what we might call the first bread and butter session of the Aviation Committee. The group, as many of you know, was started at the request of the Board of Directors two years ago. We have had two sessions since then, both of them of a somewhat general nature, their purpose being to point out the reasons why mining and petroleum engineers should be more interested in the facilities of aviation. Today we have two papers. The first is one by Mr. Eliel, of the Fairchild Company's California branch. In Mr. Eliel's absence, Mr. Gale, of the Fairchild Company, will read it. C. H. Gale.—Before I begin to read Mr. Eliel's paper, I would like to point out two instruments that he mentions- One is what he calls the solar-navigator, a new type of aerial navigating device which he has developed for use in flying cameras in aerial surveys. Flying a camera at high altitudes over unfamiliar territory is a very difficult procedure and only a few pilots in this country can do it. So far as I know, this is the first time this device has been discussed in public. Another facility I want to refer to in advance is the use of the stereoplanigraph in making contour maps from photographs. This is an extremely interesting procedure, which we are appreciating more than ever at the present time.

Jan 1, 1937

THE Section on Aerial Geologizing of the American Institute of Mining and Metallurgical Engineers convened on Monday afternoon, Feb. 17, 1936, during the Annual Meeting of the Institute. Mr. Theodore Marvin presided. CHAIRMAN MARVIN.-We hope to get through with the papers on the program in time so that you can examine the instruments that are dis-played here, and also the photographs and air views brought by the Fairchild people. This is what we might call the first bread and butter session "of the Aviation Committee. The group, as many of you know, was started at the request of the Board of Directors two years ago. We have had two sessions since then, both of them of a somewhat general nature, their pur-pose being to point out the reasons why mining and petroleum engineers should be more interested in the facilities of aviation. Today we have two papers. The first is one by Mr. Eliel, of the Fairchild Company's California branch. In Mr. Eliel's absence, Mr. Gale, of the Fairchild Company, will read it. C. H. GALE.-Before I begin to read Mr. Eliel's paper, I would like to point out two instruments that he mentions. One is what he calls the solar-navigator, a new type of aerial navigating device which he has developed for use in flying cameras in aerial surveys. Flying a camera at high altitudes over unfamiliar territory is a very difficult procedure and only a few pilots in this country can do it. So far as I know, this is the first time this device has been discussed in public. Another facility I want to refer to in advance is the use of the stereoplanigraph in making contour maps from photographs. This is an extremely interesting procedure, which we are appreciating more than ever at the present time.

Jan 1, 1936

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

SECTION I PAGE PAGE Bulletin Wanted v Northwest Mining Convention St. Louis Meeting v (Columbia Section) xvi Proceedings of the Meeting of Affiliated Student Societies... xvii the Board of Directors vii Harrison W. Craver, New Li-¬ John Fritz Medal viii brary Director xviii Herbert C. Hoover, Food. Con Library xx troller viii Pamphlets for Sale xxii President's Prize ix Membership xxxvi Emmons Memorial Fellowship. x Biographical Notice of Her¬ Meetings of Various Societies. x Mann A: Keller : lviii Personal xi Institute Committees lix Employment xii Officers and Directors lxvi Local Section News xiii

Jan 5, 1917