Search Documents

By H. G. Botset

A KNOWLEDGE of the water content of producing sands is becoming of increasing importance to the petroleum industry. It is now a generally accepted fact that practically all oil sands contain some free water. Recent experiments1 have shown that an appreciable fraction of the pore space of a sand may be filled with water while oil production from this sand is water-free. Crowther and Haines,2 in experiments on electro-endosmosis in soils, reported that there was no endosmotic flow of water when the moisture content of the soil was 14 per cent or less, indicating that the moisture content of the soil below 14 per cent was held by dif-ferent forces than the water content above this value. This result is confirmed qualitatively by Dunlap,1 who found that "as the volume of water in the voids exceeds approximately 15 per cent of the pore volume, the permeability of the core to kerosene is markedly reduced." The author3 has also found in other experiments that the gas flow through a water-saturated sand reaches essentially 100 per cent when the pores of the sand still contain from 10 to 15 per cent water. The velocities of the flowing fluid in the experiments cited were comparatively high, so that in practice one may expect, at lower fluid velocities, an even higher moisture content of the sands with water-free oil or gas production. Thus a knowledge of the water content of oil-field sands becomes of con-siderable importance in estimating petroleum and gas reserves, and effi-ciency of fluid recoveries from depleted reservoirs. Rapid and reasonably accurate methods of measuring the water content of sand cores have not been described so far in any literature that has come to our attention.4 The method described below is devel-oped from methods that have been used for some time to measure the water content of alcohols.5,6,7 It is an application of the fact that in the presence of certain organic liquids such as kerosene, carbon tetrachloride, xylol, etc., water and alcohol are only partly miscible. This relation-ship has been used for some time in the study of gasoline-alcohol mixtures where the presence of small quantities of water affect the solubility of

Jan 1, 1938

By J. H. Anderson, G. A. Parks, B. K. Jindal, H. Leslie Bullock

H. Leslie Bullock (Engineering Consultant, Oak Park, 111.) — In reading over the paper, I find that I have no quarrel with the thoroughness of investigation of the points studied, but I am forced to question the selection of oxides from oxides as the subject of the investigation, the inclusion of silica gel as an example, and to question the validity of some of the conclusions. Separation of oxides from oxide, in minerals where the liberation of values is possible by grinding, are comparatively rare. Most oxides are only slightly soluble and the action of carbon dioxide or other acid forming ingredient in the air must be added to humidity to produce surface action. Silica gel is a very special synthetic substance in which the adsorption is determined by total surface, pore dimensions and temperature. Quartz is our most prevalent oxide and its action in electrostatic separation is far more sensitive to its three thermal transition points than to humidity.

Jan 1, 1968

By AIME AIME

THE quarters provided for the session on Milling Methods, Monday afternoon, Feb. 17, were filled to capacity. Galen H. Clevenger presided and notables, such as A. W. Fahrenwald, A. O. Gates, F. A. Thomson, W. L. Zeigler and others who had not graced a milling meeting in New York in recent years, or per- haps even never before, were actually present and spoke "in person." The first paper, by A. W. Fahrellwald (T. P. 275), entitled "Classifier Efficiency ; An experimental Study," was summarized by the author, who clearly showed the inconsistency of determining the efficiency of a classifier by means of sizing tests, especially where the material classified consists of a mixture of minerals of different specific gravities. In place of sieve analysis the procedure recommended involves the use of a glass settling-tube which is considered to give ideal classification and thus serve as a standard against which mill classification will be compared and relative efficiency calculated. This procedure sounds logical. Perhaps the greatest difficulty may lie in securing an ideal classifier acceptable to every one.

Jan 1, 1930

By M. Bevis, A. F. Acton, P. C. Rowlands

Defor~nation twinning and transformation twinning modes most likely to be operative in Fe-Ni and Fe-Ni-C martensites have been determined using a new theory of the crystallography of deformation t~inning.~ This analysis shows that potentially important conventional and nonconventional twinning modes1 have been omitted in previous analyses. Discussion is given on the relevance of the predicted twinning modes to the lattice invariant shear associated with the martensite transformation in steels and to anomalous deformation twinning in Fe-Ni-C martensites. THE two most important criteria which appear to govern operative twinning modes in metallic structures1 are that the magnitude of the twinning shear should be small and that the twinning shear should restore the lattice or a multiple lattice in a twin orientation. The latter criterion ensures that the shuffle mechanism required to restore the structure in a twin orientation is simple. These criteria have been adhered to in the prediction of twinning modes2"6 in bcc and bct single-lattice structures with axial ratios in the range y = 1 to 1.09 as, for example, encountered in martensite occurring in steels. Refs. 2 and 3 in particular consider the martensite transformation in steels and the twinning modes in these cases relate to transformation twinning, and hence the lattice invariant shear associated with the martensite transformation. The list of twinning modes which can be compiled from these sources is incomplete and the ranges of magnitude of shear considered could be unrealistically small, particularly in the case of deformation twinning. The latter consideration is supported by the fact that twinning modes with magnitudes of shear large compared with the smallest shear consistent with a simple shuffle mechanism have been established in, for example, the single-lattice structure mercury7 and the multiple-lattice structure zirconium.&apos; In addition the anomalous deformation twins reported by Ftichrnan4 to occur in a range of Fe-Ni-C martensites still remain unexplained. It is clear that a comprehensive analysis of twinning modes likely to be operative in martensite In steels is required. The results of the application of a new theory of the crystallography of deformation twinningg to these structures are presented in this paper. The theory has been used to determine all shears which restore the lattice or a multiple lattice in a new orientation with magnitude of shear up to a required maximum. The orientation relationships between parent and twinned lattices are not restricted to the classical orientation relationships of reflection in the twin plane or a rotation of 180 deg about the shear direction. PREDICTED TWINNING MODES Twinning modes which restore all or one half of lattice points to their correct twin positions will be referred to as m = 1 and m = 2 modes, respectively. These modes are the most likely to describe operative modes in single lattice structures. The bcc m = 1 and m = 2 modes which have magnitudes of shear s in the range s < 2 and s < 1, respectively, have been given10 and are reproduced here in Tables I and 11. Detailed discussion of the crystallography of these modes and cubic modes in general will be discussed elsewhere (~evis and rocker, to be published). The four twinning elements Kl, &,ql,7)2 as well as the magnitude of shear s are given for each twinning mode, and the twinning modes are given in order of increasing shear. Two twinning modes are given in each row of the tables, the twinning mode Kl, Kz, ql, q2 and the reciprocal twinning mode with elements Kl = K,, Ki = Kl, q: = q2, and 17; = ql. The m = 1 and m = 2 twinning modes which describe twinning shears with small magnitudes of shear and simple shuffle mechanisms in bct crystals with -y = 1 to 1.09 are given in Tables I11 and IV, respectively. On increasing the symmetry of the tetragonal lattice to cubic, that is making y = 1, all modes listed in Tables 111 and IV must reduce to crystallographically equivalent variants of the modes given in Tables I and 11, respectively, or become twinning modes with both shear planes as symmetry planes in the cubic lattice and hence not considered in Tables I and 11. With the exception of this last type of mode only those tetragonal twinning modes which reduce to modes 1.1, 1.2, 2.1, and 2.2 of Tables I and I1 are considered in Tables 111 and IV. For values of y in the range -y = 1 to 1.09 the tetragonal modes and the corresponding cubic twinning modes have approximately the same magnitude of shear. The twinning modes listed in Tables 111 and IV are therefore by the criteria given above the most

Jan 1, 1969

By M. J. Mullikin, J. B. Conway

for use in describing combined first- and second-stage creep data. In the above ?o represents the instantaneous strain on loading, ?t the limit of transient creep, ?S the steady-state creep rate, t the time, and ? a constant leading to the exhaustion rate of transient creep. It was noted that this equation was similar in form to that proposed originally2 by McVetty. This type of equation was also suggested by Andrade and Aboav3 in studies of the shear strain of cadmium. Calculation of the constants ?o, ?t, ?, and ?s, in Eq. [ l] is somewhat involved due to the slight complexity of this relationship. In the paper by Garofalo a computer approach based on a least-squares analysis was recommended. Such an approach involves a trial and error solution but when a computer facility is available the difficulties in this calculation are of little consequence. It does mean however that the evaluation of this type of equation would become quite tedious if computer facilities were not available. Some recent studies have identified a fairly straightforward method for calculating the constants in the Garofalo equation. While not leading to a least-squares evaluation the approach is accurate and is recom-

Jan 1, 1967

By F. D. Rosi, C. A. Dube, B. H. Alexander

The slip and twinning planes have been determined in deformed crystalsof titanium by an X-ray method of analysis. The slip planes are of the type {1010} and {1011}, while the twinning planes are of the type {1072}, {1121}, and (1122). In the case of the predominant (1010) slip, a type I digonal axis of indices <1120> was the effective slip direction. Microscopic observations on the appearance of the three twin types disclosed a distinct difference in their shapes, and an attempt was made to correlate this difference with the amount of twinning shear. The slip mechanism was discussed on the basis of the difference in c/a ratios for the common hexagonal close-packed metals. IT is a general rule that slip in metals occurs most easily on the planes of greatest atomic density and of the largest interplanar spacing, and that the direction of slip is a close-packed direction. Thus, of the hexagonal close-packed metals which have been investigated by the German school in the decade 1925 to 1935 (cadmium, zinc, and magnesium), it has been found that slip occurs on the basal plane (0001) and in a <1120> direction.&apos; In the case of magnesium above 225oC, slip occurs on a first-order pyramidal plane (1011) as well as on the basal plane.&apos; The hexagonal metals, moreover, deform in part by twinning, and, again with the exception of magnesium at elevated temperatures, the twinning plane has always been reported to be a second-order pyramidal plane {1012).&apos; In view of this consistency in the plastic behavior of these metals, it has been supposed that the same slip and twinning elements would be operative in the other important hexagonal close-packed metals (titanium, zirconium, and beryllium), although there are some reasons why this may not be so. Referring to the tabulation in Table I of the axial ratios of the important metals in this structural class, it may be seen that they can be categorized into three distinct groups depending on the value of their c/a ratios. In the first group are cadmium and zinc with large positive deviations from the ideal ratio for closest packing. This expansion in the direction of the c-axis would be such as to accentuate the basal plane as the slip plane, because it increases the interplanar spacing. The second group includes cobalt and magnesium, which closely approximate the ideal ratio. In the third group are zirconium, titanium, and beryllium whose axial ratios are decidedly less than the ideal. The lattice of the elements in this group is compressed along the c-axis which, in effect, tends to make the basal plane less favorable for slip inasmuch as it reduces the interplanar spacing and the atomic density of this plane. Thus, for metals in the third group, it may be said that there is a certain indefiniteness about the glide plane, in that planes other than the basal plane may be expected to operate. The fact that magnesium begins to exhibit planes other than the normal slip and twinning planes at elevated temperatures may indicate that this behavior will become more pronounced in metals of lower axial ratios. For this reason it might be expected that the slip and twinning behavior of zirconium, titanium, and beryllium would be different from that found in cadmium and zinc. One indication that there is a difference is reflected in the recent work which has been done on the deformation textures of these metals."&apos; As will be shown later, there is a significant difference between the rolling textures of cadmium, zinc, and magnesium on the one hand, and zirconium, titanium, and beryllium on the other, and this difference suggests that the mechanism of plastic flow is not the same in these two groups of metals. From these considerations, therefore, it may be seen that there are good reasons why it cannot be concluded that titanium will have the same crystal-lographic elements of slip and twinning as those exhibited by zinc and cadmium. For the complete determination of these elements it would be most advantageous to have single crystals. However, much valuable information can be obtained by using coarse grained polycrystalline specimens, provided the grains are sufficiently large to permit X-ray

Jan 1, 1954

By E. C. Bitzer

THE primary object of the work described in the following pages was to simplify the equipment in the separating circuit of the heavy-media process by substituting a spiral classifier for the separatory cone. Mechanical considerations were the leading attraction and the best that was hoped for on metallurgical performance was that the new vessel would give results equal to those obtained by conventional equipment. Tests have demonstrated in commercial operation on iron ore that the mechanical advantages of the spiral separator are about as predicted; also, the metallurgical performance is superior to the cone on the ores treated. Treatment of iron ore involves the separation of two products: a concentrate that sinks and a float product that contains true float material plus a controlled division of interfering middling. The middling material is heavier than the average specific gravity of the separating medium. Recent work with the spiral separator on Tri-State zinc ore showed that the middling material had to be recovered as concentrate because this fraction contained the bulk of the-zinc in the ore. It has been demonstrated that it is possible to make three products with the new separator on an ore such as this: a float tailing, a float middling, and a high grade heavy sink product. It appears from this last work that the new separator has definite mechanica1 and metallurgical advantages over any type of separating cone for treating feed that contains large amounts of material of a specific gravity close to that of the separating medium. However, either type of separator should perform equally well, metallurgically, on feed that is free of middlings. Each series of experiments with the spiral separator as required additional work to fully develop the possibilities of the machine. For this reason the paper is divided into chronological parts. History of Development A drag-type classifier was first proposed as a substitute for the cone separator by Butler Brothers technicians during the initial tests with galena medium at Crosby, Minn., in 1937. The desire for finding a substitute for the cone arose from trouble with interfering middlings and certain operating disadvantages of the cone. The possibility of using a spiral classifier was also suggested at this time by Emmett Butler and C. J. Abrams. However, inability to satisfactorily recover fine galena, which was used as a medium, terminated all development work at Crosby. During the winter of 1937--1938 investigation started on magnetic medium with concurrent s development of the inverted or closed- top cone, which was found necessary to eliminate iron-ore middlings with the float product. About

Jan 1, 1947

By M. G. F. Söhnlein

In a Bolivian tin concentrator an appliance was needed to furnish a suitable product for fine jigging from a pulp of the following composition: Mesh Per Cent. + 20 8.0 40 36.5 + 60 9.0 + 80 10.5 + loo 5.5 4-150 1 4.5 -150 25.0 99.0 Loss 1.0 In the jigging process, particles of cassiterite as small as 0.1 mm. can be recovered, provided they are not present in excess, that is if the material treated on the jigs contains sufficient coarser sands to keep the interstices between the grains open. Removing the fine material from the pulp by screening, to prepare the jig feed, is impractical, because that means the use of an 80-mesh screen or finer, and is not as effective as hydraulic classification. A screen would eliminate mineral grains from the feed which can be recovered by jigging, and in addition would throw more gangue and low-grade middling on to the jig. Formerly a one-spigot Richards vortex classifier had been used to accomplish this separation, but the tangential openings through which the hydraulic water enters became clogged by fine vegetal matter with which the water was contaminated, and which it was impossible to remove from the water. Consequently the work of the classifier was imperfect and a good deal of slime was sent to the jig. When designing the plant referred to in this paper it was decided to use a hydraulic classifier as shown in Fig. 1. The essential features had been copied from the Anaconda classifier.&apos; This remodeled classifier consists of a truncated pyramidal wooden hopper A with an attachment of cast iron

Jan 1, 1917

By B. W. Gandrud

WET-PROCESS coal-washing tables as we know them today have been in use in this country for approximately 25 years. The literature records only a few table installations worthy of note prior to adoption of the present-day differential-motion table. According to Phillips,&apos; six Campbell bumping tables were being operated by the St. Bernard Coal Co., Earlington, Ky., in 11893. As late as 1923, according to Richardson, 2 72 such tables were in operation in the Rosedale washery of the Cambria Steel Co., at Johnstown, Pa. Bumping tables probably were not used to any considerable extent except in the plant at Earlington, and at two or three plants in Pennsylvania, but they may be considered as forerunners of the present-day coal-washing table. The transition from bumping tables to the type of tables now in use signalized a revolutionary change in table design. The advantages of the new design over the old were so outstanding as to make its adoption inevitable. BUMPING TABLES Bumping tables, as the name implies, utilized a bumping action for conveying the refuse and discharging it over the refuse end. The tables were hung from rods attached to overhead supporting beams. A shaft and cam arrangement at one end of the table served as the actuating mechanism and imparted to the table an endwise, back-and-forth, swinging motion. A bumping block was fixed in the proper position at the shaft end, so that the table would strike against it at the end of each backward swing. The hanger rods or stirrups were so adjusted as to give the table a slight uphill slope toward the refuse end; that is, the end next to the driving mechanism. The feed box was near the upper end, of the table and designed to spread the mixture of coal and water over the width of the table. Wash water was added a short distance below the feed box with the table in motion and coal mixed with water being fed to it through the feed box, a certain amount of stratification took place, depositing heavy refuse at the bottom of the bed in contact with the surface of the table. Constant bumping and a certain amount of

Jan 1, 1943

By R. M. Brick

THE etched microstructures of cold-worked alpha brasses, after reduc-tions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonomously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {111}, in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans&apos; results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson5 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into sym-metry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By O. E. KEOUGH

AT the Tooele custom lead-zinc ore concentrator,&apos; two sections, each having a daily capacity of 500 to 600 tons, are operated on slightly different types of ores with but little difference in flow sheet and reagents. The ores comprising the two general classes are the coarsely crystalline type, with low pyrite and sphalerite low in iron content, from the Park City district, and the more finely disseminated higher pyrite ores from Bingham, which are more difficult to treat by flotation. Laboratory testing determines with which general class a new ore will work better. The ores are crushed to minus 1 1/4-in. size at either the Utah Ore Sampling Company&apos;s plant at Murray, Utah, the Tooele smelter sampling plant, or the crushing plant at the concentrator. The ores for each section are mixed to maintain as nearly as possible uniform lead and zinc contents.

Jan 1, 1930

By John J. Cioston

THE steadily rising flood of gold production from all parts of the world has created an avalanche of rumors regarding the stability of the present price of this metal. Markets have been unsettled from Johannesburg to London from New York and Toronto to Melbourne, despite repeated denials from, American and British authorities of any immediate intention to alter the price. Various economists and financial writers have blossomed forth with predictions that the price would be set at the old level of $20.67 per oz.; some have even been so brash as to state That a price of $15 would be necessary to bring production within control. These effusions, based entirely upon monetary theories and with no regard to production costs, serve to confuse rather than clarify the situation.

Jan 1, 1937

By Maurice Grieves

The great majority of shafts constructed today are still excavated by drilling and blasting, a method which changed very little in over 100 years until the introduction of the mechanical lashing unit and cactus grab by the South Africans, which enabled muck to be removed as fast as massive hoisting systems could handle it and resulted in very rapid rates of sinking. Record breaking month&apos;s performances were achieved at -Hartebeestfontein No. 4 shaft, October 1960-337.1 m; Western Reefs No. 4 shaft, October 1961-340.7 m; and Buffelsfontein eastern twin shaft, March 1962-381.2m. The method was very labor-intensive, requiring a crew of over 60 workers at the shaft bottom during the drill cycle. Safety precautions were strict, but in the drive to achieve rapid advance, cases of personal injury were still somewhat high because of the large number of people engaged in this potentially hostile environment. The South African method, as it came to be referred to throughout the rest of the world, was adopted in the United Kingdom in the late 1950s in a modified form with greatly reduced manpower and nonsimultaneous sinking and lining, which was insisted on by the British Mines Inspectorate. In that instance, it was successfully used to sink the 7.3-m-diam concrete-lined shafts at Kellingley to 770 m depth, with rates of advance of over 90 m/month achieved, a British record at that time. During the sinking of the 1.15-km-deep twin shafts at Boulby potash mine in the UK in 1970, the method was again used, but for the first time ever in Britain exemptions from the mining code permitted the use of crash beams, crash doors, jack catches, and semi-simultaneous sinking and lining techniques. New British shaft sinking records of over 120 m/month were achieved in both shafts. Similar equipment and techniques were used in the early 1970s to sink several deep shafts in Canada, notably Creighton #7 and the Con zinc mine at Yellowknife in the NW Territories. Today, this equipment is standard for deep shafts in the US and the rest of the world. However, with the tremendous escalation in mining labor costs, the impact of health and safety legislation, and environmental regulations, coupled with a very real shortage of miners willing to work in this exposed situation it was apparent that an alternative to the labor-intensive conventional method of shaft construction had to be found. Recognizing the trend is inevitable, one or two major German shaft sinking contracting firms began to take a fresh look at full face boring techniques applied to tunnels and raise bored shafts. The results were most encouraging. Tunnel drivage techniques using moles had developed considerably from Colonel Beaumont&apos;s original channel tunnel machine circa 1880 to the superbly engineered Priestley machine selected to cut the British side in 1975 and the double shielded Robbins Grandori borer on the French side of the English Channel. Full face tunnel machines were being successfully used to drive uphill in inclined shafts in Austria and Switzerland. At Mapprag in Switzerland, the Demag mole drove the first (intentional) vertical transition and curve, and then went on to successfully complete the 730-m-long penstock shaft at an inclination of 35°. In Austria, the Wirth mole drove the Kaprun Glacier ski-lift railcar tunnel at record breaking rates of 457 m/MONTH (best 30 m/d) through green schist at an inclination of 29° for a distance of 3.35 km while the Hydro tunnel at Sarrelli in Switzerland was being driven by the Robbin&apos;s mole at an inclination of 35°. Simultaneously, extremely promising results were obtained using large assemblies of cutter discs on raise borer heads, such as the 4.87-m-diam X 460-m-deep shaft raised by Teton for Jim Walter Resources Inc. Bearing in mind that most mine shafts in the future (unless in exceptionally competent rock) will require some form of lining, and the trend will be toward deeper shafts as the more easily accessible mineral deposits become exhausted, it was seen that normal raise boring had definite limitations in vertical accuracy, in the limitation imposed by the drill string on the available torque that could be applied to the cutter head, and in the risk of collapse of the unsupported shaft rock wall in friable or jointed and fissured ground, since it is not possible to apply any form of temporary support until the permanent lining is being installed. A further problem was the economics of installing a subsequent lining, necessitating setting up a headgear and hoisting arrangement approaching in size that required for conventional drill and blast sinking and lining. Because of the economics, German contractors opted for a phased transition from drill and blast to the full face, rodless, out of the solid shaft mole, by starting off with a down-the-hole shaft boring machine -without a drillstring-but using a pilot hole to get rid of the muck.

Jan 1, 1982

By J. K. Furst

THE reasons for manufacturing steel by the duplex process are, briefly: saving of time; increasing output for capital invested; and avoiding the difficulty sometimes experienced in obtaining scrap. On account of the latter reason, some plants duplex only at such times as the price and quantity of scrap in the open market warrant. At some plants the use of the duplex process enables, the blast-furnace practice to be simplified, because the furnaces run more smoothly and produce more iron when not held to a strict specification as to the silicon and phosphorus therein. The duplex process was practiced in Witkowitz as far back as 1878, but it was left to the steel makers of this country to develop it along practical, commercial lines. The American companies manufacturing steel by the duplex process at the present time are: Tennessee Coal, Iron & Railroad Co., Maryland Steel Co., Bethlehem Steel Co., Pennsylvania Steel Co.; Jones & Laughlin Steel Co., Colorado Fuel & Iron Co., Lacka-wanna Steel Co., Dominion Iron & Steel Co. of Canada. All of these companies, except the Dominion Iron & Steel Co., combine the acid Bessemer with the basic open-hearth process, while the latter combines the basic Bessemer with the basic open hearth. The Tennessee Coal, Iron & Railroad Co.&apos;s Plant The installation of a converter of 15 tons capacity at the Ensley plant of the Tennessee Coal, Iron & Railroad Co. in 1904 marked the introduction into this country of the duplex system. The experience gained in the employment of the Bessemer converter had demonstrated that there was a shortening of .the time required in the open-hearth furnace and a reduction of the outlay for fuel and lime, thus affording substantial evidence of the economies resulting from this method.

Jan 10, 1914

By Paul H. Price, John P. Nolting

The history of the salt industry in West Virginia dates back nearly two hundred years; howTever, the history of salt as an important raw material for the chemical industry is much more recent. The earliest record of West Virginia salt was in 1753, when a raiding party of Shawnee Indians attacked frontier settlements in Virginia taking captive a number of the pioneers. One of these, who later escaped and returned to her friends, described how the Indians camped at a salt spring on the banks of the Kanawha River and evaporated the water to obtain a supply of salt to take back to Ohio with them. Settlement of the Kanawha Valley began in 1774, that same year the Battle of Point Pleasant ended the Indian&apos;s power in the Ohio Valley; and settlement of the Kanawha Valley progressed rapidly with a consequent increase in the importance of the Kanawha Licks as a source of salt. In those days the evaporation of the brine was a family matter for which the family wash-kettle was commandeered. In 1797, Elisha Brooks erected the first salt furnace in the Kanawha Valley. It consisted of two dozen small kettles set in a double row, with a flue beneath, a chimney at one end, and a fire bed at the other. He obtained his brine at a depth of 20 to 30 ft by sinking hollow logs, called "gums" into the salt lick and dipping the brine with a bucket. His production was about 150 lb a day and sold for 8 to 10 cents a pound. In 1806, the Ruffner brothers, David and Joseph, prospected for and drilled the first well in America using a spring pole and steel chisel bit. After several failures they succeeded, in 1808, in drilling to a total depth of 59 ft where they secured a good flow of strong brine. Most standard drilling tools, jars, casing, and practically all the basic oil well drilling machinery now in use, were developed in the drilling of salt wells. To evaporate this brine, the brothers built a wood-burning furnace similar to that of Brooks but with a better arrangement and with more and larger kettles. When production was started they reduced the price of salt to 4 cents a pound. By 1817, there were some 30 salt furnaces in the Kanawha area. It was in this year that bituminous coal first was used as an industrial fuel. David Ruffner again pioneered the way by converting his furnace for the consumption of coal. This year also brought about the formation of the first trust which controlled production and set a price of 1 cent a pound for the salt.

Jan 1, 1950

Jan 1, 1968

By E. C. Hopkinson, A. H. Youmans, R. A. Bergan, H. I. Oshry

A new log has been developed for quantitative formation evaluation which is based on a measurement of the length of time slow neutrons survive before they are captured in the rocks and fluids. The logging instrument employs a cyclically pulsed neutron generator and a gated scintillation counter which is synchronized with the source. The source emits short, intense bursts of 14 mev neutrons once every 1,000 microsec and is quiescent between bursts. During the period the source is quiescent, the detector is electronically actuated for two independent preselected intervals. A comparison of the counting rates during these two intervals gives a measure of the rate of decay of the slow neutrons and of the associated gamma radiation. The average neutron lifetime in most earth formations is in the range from 50 to 500 microsec. It can be measured during a continuous logging operation at conventional logging speeds. The design of the logging instrument is described and the results of tests are compared with theoretical predictiom. Formulas are developed which give the relationship between log response and formation properties. It is shown that the method is particularly sensitive to formation fluid salinity, and that salt water saturation can be measured accurately in either cased or open hole. The measurement can be made independent of borehole size, fluid type, casing and tool position in the hole by properly selecting the intervals during which the measurements are made. The results of tests with a prototype logging tool are given. INTRODUCTION A new nuclear logging system has been developed which employs the Accelatron,* an accelerator-type neutron source, and accurately measures formation brine saturation in an entirely new way. It has produced a type of formation log with better sensitivity, greater sampling depth and simpler quantitative interpretation than any other nuclear log thus far suggested. The new Neutron Lifetime Log* employs a pulsed electromechanical neutron source and a synchronously gated radiation detector. A prototype instrument has been field tested during recent months to demonstrate the operability of the apparatus and the feasibility of the method. Tests in wells and simulated boreholes have confirmed theoretical predictions and have shown that formation param ters can be measured independent of casing and other borehole parameters. Preliminary results of field tests have indicated that the log may have important and widespread applications. BASIC PRINCIPLE OF NEUTRON LIFETIME LOG The Neutron Lifetime Log is based on the fact that neutrons emitted by a source in a well are rapidly but not instantly captured by the material around the source. Their capture is a matter of statistical probability; the greater the number of capturing nuclei and the greater the "capture cross section", the greater is the probability that a neutron will be captured quickly. The average life of a thermal neutron in vacuum is about 13 minutes, but in common earth materials, the average neutron life ranges between extremes of about 5 rnicrosec for rock salt and perhaps 900 microsec for quartzite. The Neutron Lifetime Log responds to variations in this average neutron life. The theoretical basis for a log of this general type has been well understood by nuclear logging experts in many laboratories both in America and in Russia, and develop mental work along these lines has been in progress for many years. The Russian literature has reported both theoretical and experimental work1,2 but in this country there have been no published reports of progress toward a practical logging instrument. The logging instrument is designed to measure radiation produced by slow neutrons during selected intervals when no neutrons are being emitted by the source. The source is arranged to emit neutrons in bursts or pulses. During the quiescent interval between the pulses, it is possible to observe the exponential "decay" of the neutrons and the neutron-induced radiation as the individual neutrons progressively disappear due to capture by atoms in the formation or the borehole. When a short pulse of 14 mev neutrons is emitted by a source in a borehole, the individual neutrons are slowed to thermal energy within a few microsec. Thus, a cloud of "slow" neutrons is formed around the source within 10 to 50 microsec after the pulse. This cloud is most dense within a few inches of the source, and is progressively less dense out to a radius of about 3 ft, where radiation from the source is practically undetectable.

Jan 1, 1965

By W. F. Carew, F. A. Crossley

IT has been reported that the Ti-8 pct A1 alloy is ductile as water quenched from 800°C but brittle as annealed at 650 °C." The present, somewhat limited, investigation was undertaken to discover the cause of the embrittlement. In order to evaluate to some extent the continuity of the embrittling phenomenon, alloys of 6, 8, and 10 pct A1 were studied. Subsequent to the completion of most of this work, Ence and Margolin reported that a Ti,A1 phase exists and that two or more unidentified compounds may exist in the Ti-A1 system.&apos; Materials, Equipment, and Techniques The alloys were prepared using Kroll process sponge of 124 Bhn hardness. In addition, some 8 pct A1 material was made with iodide titanium. The sponge-base alloys were prepared as melts of 4 lb or more by double arc melting. The iodide Ti-8 pct A1 alloy was prepared as 200-g buttons. The alloys were forged at temperatures of 980" to 1150°C. Results of chemical analyses are given in Table I. A Baldwin-Southwark 60,000-lb capacity tensile machine, equipped with an autographic stress-strain recorder, was used for the tensile tests. Standard tensile test specimens, 0.252 in. diam, were used. Standard Charwy V-notch impact specimens were tested using a -kiehle machine. specimens were sealed in evacuated Vycor bulbs for heat treatment. Powder samples for Debye-Sherrer anal- ysis were prepared by filing and screening through 325 mesh. The —325 mesh fraction was taken in an effort to concentrate a microstructural constituent assumed to be less ductile than the a phase. The powder samples were stress relieve2 by annealing

Jan 1, 1958

WILDER D. BANCROFT,* Washington, D. C. (written discussion?).¬In two-phase systems there are three possibilities and Mr. Alexander has only considered two. We may have the first phase the internal one and the second the external one; we may have the first phase the external one and the second phase the internal one; and we may have both phases continuous. This last case occurs when we have a roll of wire fencing standing in the air; the wire is continuous and so is the air. It is quite probable that this case occurs very often in alloys and it it, therefore, important that it should not be overlooked. With gulch,

Jan 3, 1919

By Archer Wheeler

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until .June 1., 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operations and appliances of the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detailed account, of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag.

Jan 8, 1913