Search Documents

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

By W. F. Carew, F. A. Crossley

IT has been reported that the Ti-8 pct A1 alloy is ductile as water quenched from 800°C but brittle as annealed at 650 °C." The present, somewhat limited, investigation was undertaken to discover the cause of the embrittlement. In order to evaluate to some extent the continuity of the embrittling phenomenon, alloys of 6, 8, and 10 pct A1 were studied. Subsequent to the completion of most of this work, Ence and Margolin reported that a Ti,A1 phase exists and that two or more unidentified compounds may exist in the Ti-A1 system.' Materials, Equipment, and Techniques The alloys were prepared using Kroll process sponge of 124 Bhn hardness. In addition, some 8 pct A1 material was made with iodide titanium. The sponge-base alloys were prepared as melts of 4 lb or more by double arc melting. The iodide Ti-8 pct A1 alloy was prepared as 200-g buttons. The alloys were forged at temperatures of 980" to 1150°C. Results of chemical analyses are given in Table I. A Baldwin-Southwark 60,000-lb capacity tensile machine, equipped with an autographic stress-strain recorder, was used for the tensile tests. Standard tensile test specimens, 0.252 in. diam, were used. Standard Charwy V-notch impact specimens were tested using a -kiehle machine. specimens were sealed in evacuated Vycor bulbs for heat treatment. Powder samples for Debye-Sherrer anal- ysis were prepared by filing and screening through 325 mesh. The —325 mesh fraction was taken in an effort to concentrate a microstructural constituent assumed to be less ductile than the a phase. The powder samples were stress relieve2 by annealing

Jan 1, 1958

By Archer Wheeler

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until .June 1., 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operations and appliances of the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detailed account, of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag.

Jan 8, 1913

By Norikazu Hashimoto

SILICIDE coatings on refractory metals are often applied by transporting a silicon halide vapor to a hot metal surface . The coatings are usually grown by solid-state diffusion reaction. The diffusion is often slower than the vapor transport and hence may become rate-controlling.

Jan 1, 1968

By T. A. Read, H. M. Otte

THEORETICAL analysis by Wechsler, Lieberman and Read of the crystallography of martensite formation has shown that the requirement for the existence of a macroscopically undistorted plane between austenite and martensite permits a calculation of the indices of the habit plane of the marten-

Jan 1, 1958

By Gordon E. Agar

Several correlations have been proposed to relate energy consumption and size reduction in comminution, and although these are arrived at from different starting points, it is postulated that they are all statements of the same basic concept. To test this postulate, the dry ball mill grindability of langbeinite was determined, and the results were analyzed according to the various methods. An examination ' of the energy-particle size relationships proposed in the recent past revealed that they had much in common. In fact, the conclusion was tentatively drawn that these expressions were essentially the same, even though they were arrived at from quite different basic premises. The equations attributed to Charles2 and Holmes3 were shown to re- duce to the same single equation, W - A K-3, and the simulated continuous test used by Maxson et al.4 was shown to give the best experimental value of the required empirical parameter, ß. Furthermore, the size distribution parameter a in the Schuhmann equation, y - (x/K)2, was shown to be equal to ß in many cases. The kinetic approach used by Arbiter and Bhrany5 should give the same results as the Maxson test procedure; however, the batch operation used by Arbiter and Bhrany could not produce data that would be as precise as the simulated continuous technique. To test the validity of these conclusions, the simulated continuous method was used to obtain data on the dry grinding of langbeinite. The results are discussed in terms of the various equations and approaches. APPARATUS AND MATERIAL A ball mill with internal dimensions of 17.5 cm (6 7/8 in.) in length by 19.4 cm (7 5/8 in.) in diam was loaded to 50% of its volume with balls 3.2 cm in

Jan 1, 1969

By Scott Turner

MY YEAR OF SERVICE as president of the A.I.M.E. came at a time when the mineral industry had suffered severely because of disturbed economic conditions throughout the world. The Institute, an integral part of this industry, had been similarly affected. Its membership and revenues decreased; it was confronted by problems of retrenchment at a time when its vigorous operation was especially important to its members, of some moment to the mining industry, and of value to the nation. Throughout the last year, the recession of activity in our industry continued with slight abatement. Your Board accordingly exercised such economy within the Institute as was possible without impairment of essential functions. It endeavored to aid in sustaining the morale of members, their sense of professional unity, and their interest in maintaining research and the interchange of scientific and technologic data upon which the progress of our industry depends. Effort was made to assist in the difficult task of finding employment for needy members; our endeavors have met with some success.

Jan 1, 1933

By J. W. Downey, S. T. Zegler

A study has been made of the occurrence of Phases having the Cr30-type structure in ternary alloys having the general composition where B cept for iron and copper all the B components are known to form binary compounds having the type structure. The occurrence of the struc-ture type in the ternary alloys was investigated using optical and X-ray metallography. The results indicate that iron can replace virtually none of the cobalt in at 900°C, but substitutes for nickel in up to the approximate composition tually insoluble in V3Ni and 2) and exhibit complete solubility. At 100 nickel can be substituted for cobalt in VSCo up to the composition solubility; and 3) in the system , two solid solutions having the type structure occur. At the same temperature, 1000°C, V3Si exhibits limited solubility for V3Co but is completely mis-cible with V3Ga. Lattice parameters have been determined for all the binary and ternary phases. The solid solutions are discussed in terms of the atomic size and electronic factors which are thought to influence the occurrence of Cr30-type phases. The binary compounds V3Co and V3Ni were found to form peritectoidally from o phases and a vanadium, the former compound at a temperature between 1000" and 1050°C, the latter between 800°and 900°C. The substitutions of nickel and rhodium for cobalt in V3Co were determined not to raise the superconducting transition of VSCo to a temperature as high as 2°K. The occurrence and stability of binary intermediate phases having the Cr30- or A15-type structure (space group o;, Pm3n) have been discussed in several recent papers . Vanadium forms the struc -ture at or near V3B stoichiometry with all the mem -bers of the cobalt and nickel groups in the periodic table and also with Au, Ga, Si, Ge, Sn, P, As, and Sb. This paper describes a survey of the occurrence of the CrsO-type structure in ternary alloys having the general composition V3(B, B') where B and B' are Fe, Co, Ni, Cu, Rh, Ir, Si, and Ga. The purpose of the survey was to clarify the connection between the position of the B partner in the periodic table and its CrsO-type phase-forming tenden~y.~,~ The survey is part of a broader program concerned with the influence of B-partner substitutions on the superconducting transition temperatures of CrsO-type compounds. The transition temperatures, Tc, of some of the ternary Cr,O-type phases found in the survey are also discussed in this paper. EXPERIMENTAL PROCEDURE The alloys were prepared by arc-melting in an A-He atmosphere and were in the form of buttons, weighing approximately 3 g. The metals used in their preparation were received from commercial sources and were in all cases 99.9+ pct pure. The vanadium was spectrochemically pure except for 800 ppm of Si, 200 ppm of Fe, and 200 ppm of Al. For study of each pseudobinary system at least seven alloys were prepared having the general compositions case of alloys containing gallium, melting losses were small, usually less than 0.3 pct of the total weight of the metals charged for melting. Melting losses were somewhat greater for gallium alloys, ranging in general from 0.9 to 5.0 pct. Ternary V-Si-Ga alloys were chemically analyzed and the results are given in Table I. The analyses show most alloys to be within 2 at. pct of the intended composition. Throughout the balance of the paper the intended compositions are used in discussing the alloys. The cast buttons were annealed within evacuated quartz capsules for times ranging from 3 to 6 weeks at temperatures between 800" and 1000°C and water-quenched. The phases present in the annealed and quenched alloys were identified by optical and X-ray metallography. X-ray diffraction photograms were made with powders prepared from the bulk specimens, by the use of a 114.6-mm-diam powder camera with copper irradiation. The lattice parameter of CrsO-type phases and their standard errors

Jan 1, 1963

By George L. Reiter, George B. Clark

Commercial strip mining of coal was first begun in the state of Illinois in 1911.l The annual tonnage of coal produced from coal strip mines in the state was very small until 1924, when the strip mines shipped 1.68 pct of the total state shipping mine tonnage. Since then, strip mines have gradually come into their own by producing a sizable percentage of the coal produced in the state. Table 1 shows the coal tonnage shipped from both underground and strip coal mines in the state of Illinois for selected years. The table illustrates the major role that strip mines play in the state's coal industry. Today, strip mining is generally conducted in areas where the coal seams lie so close to the surface of earth that a stripping method of mining the coal seam is cheaper than an underground method. Strip mining not only recovers 100 pct of the coal deposit, but may also be used as a method of mining large acreages of coal abandoned by the closing of underground mines. Open cut or strip mining is a very highly mechanized method of producing coal and is carried on in three distinct and separate operations. The first of these is uncovering or exposing the coal seam so that the coal is made available for mining. The second operation is that of actually mining the coal. The third operation is the washing, crushing and grading of the coal according to the producer's market. Description of Shovel The Marion 5560 power shovel is used in the first of these three operations. The large electric-powered shovel works forward and back across the coal deposits, removing the overburden of dirt, rock, and clay in successive cuts of 30 to 60 ft deep and 40 to 80 ft wide. The shovel has a maximum cutting height of 95 ft, but around 60 ft is considered to be the maximum economical cutting height by the operators. The smaller the depth of cut, the more economically the shovel will operate until a minimum cut of 15 ft is reached, below which the efficiency decreases rapidly. The Marion shovel may be used in tandem stripping in excessive depths of overburden. The other type of excavating equipment used in the tandem team is generally a dragline with a long boom of about 180 ft. In tandem stripping, the dragline is used to remove the upper portion of the cut and to place it at a maximum dumping radius from the place of removal. The Marion 5560 power shovel is then used to remove the overburden left above the coal seam and to deposit it at the shovel's maximum dumping radius. The Marion 5560 power shovel is of gigantic proportions. It has a 102 ft 6 in. boom and 32 cu yd dipper and is

Jan 1, 1950

Members Dues Resignations, Suspensions and Expulsions Institute Meetings Board of Director?s Meetings Directors and Officers Duties of Officers Committees Nomination and Election of Officers Publications Divisions, Local Sections, Affiliated Societies Amendments [As REVISED FEBRUARY 21, 19281 ARTICLE I MEMBERS-QUALIFICATIONS AND ELECTION , SEC. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Associates; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that Junior Associates, and all Members and Associates whose residence shall be outside of the United States of America, Mexico and Canada shall not be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1928

By E. J. Horwood

The varying physical character and large extent of the Broken Hill lode necessarily involve the employment of a variety of underground methods. The lode had its origin in an extensive fault plane traversing metamorphosed schists conformably, as a rule, with their beds of stratification. The underground waters carrying minerals in solution deposited their contents. in the original cavities formed by the faulting action, and in the enlargements of these cavities due to dynamic forces brought to bear on the rocks, more especially on the hanging-wall side of the fault, This deposition was supplemented by metasomatic replacement of a portion of the original rock contents by the argentiferous sulphides of lead and zinc which form the staple products of the district. Although the orebody is practically continuous throughout the mines, its width varies greatly, ranging from a few feet to about 350 ft. The widest portions occur in conjunction with huge folds in the inclosing country rock, almost exclusively on the hanging-wall side. The ore it these folds pitches to the south in the southern half of the field, and to the north in the northern half; there are, however, undulations in these ore channels evidently due to compression of the rocks in the direction of the channels. In the earlier days, before the orebodies had been opened up: vertical cross-sections across these bulges in the hanging wall gave the lode the appearance of the "saddle formation," so well exemplified at Bendigo in Victoria; but subsequent development of the ore channels ha; long since proved that the formations in the two districts are entirely different. The depth reached by the zone of complete oxidation of the sulphide, varies from about 250 to 550 ft. from the original outcrop while partial oxidation extends in places below the 1,000-ft. level. The result of oxidizing influences has been the production of ore of every grade of cohesiveness, from that of dry sand to that of hard compact rock.

Jan 1, 1916

By Richard F. Miller

The investigations of large-grained specimens carried out by Polanyi and Schmid,l Sykes,2 Goucher,3 Yamaguchi,4 Gough, Cox, and Sopwith,5 Carpenter and Elam,6 Aston,7 and others have shown qualitatively that grain boundaries restrain the deformation of adjacent crystals. But whether or not the influence of the grain boundary is confined to the glide planes intersected by the boundary has not been demonstrated in any of these investigations, nor has there been carried out any quantitative analysis of the influence of a boundary on the deformation of a crystal. Indeed, the specimens employed in the previous work contained so many complicating factors that it would have been difficult to observe any variation of the extent of the influence of the grain boundaries in relation to their sizc. The specimens were small, the grain boundaries irregular and at no particular angle to the specimen axis or the

Jan 1, 1934

By AIME AIME

BY COMBINING the sessions on reduction and refining of copper, lead and zinc it was possible to devote an entire day to nonferrous metallurgy. Four interesting papers were presented at the morning session and four more in the afternoon. In the discussion of papers on copper, F. R. Pyne acted as chairman, with H. M. Shepard as vice-chairman, whereas for those on lead and zinc, F. F. Colcord acted as chairman, with C. R. Hayward as vice-chairman. The paper by P. D. I. Honeyman on the smelting of raw concentrates in the reverberatory furnace was presented by Mr. Pyne and discussed by Messrs. Mazany and Hayward. The interesting paper by E. S. Bardwell, com- paring the use of various fuels in copper-refining furnaces at Great Fails, Mont., was presented by Mr. Shepard and discussed by Messrs. Boggs, Gronningsater and Hayward. That by R. G. Knickerhocker, describing the stationary basic copper converter at Messina, Transvaal, was presented by Mr. Pyne, together with a written discussion by c. R. Kuzell, of the United Verde Copper co. It was an interesting illustration of how well-known processes may sometimes be modified to fit into unusual conditions.

Jan 1, 1932

By P. Gordon, A. S. Iyer

IN a paper on the mechanical behavior of heat-treated steel, N. H. Polakowski' put forward arguments to the effect that the stored energy resulting from the deformation of metals should be reduced during the inital stages of subsequent deformation carried out under conditions which produce work softening. At the time (1957) the only energy measurements available as indirect evidence on this point were the results of M. M. Degtyarev,2 some of which Polakowski reproduced in his Fig. 6, and which are again reproduced here in Fig. 1. The solid lines in the upper part of Fig. 1 are Degtyarev's, the dashed Lines Polakowski's prediction of the true trend of the stored energy in copper samples pre-strained in tension and then given various amounts of subsequent compression. The accuracy of this prediction has been borne out by some experiments carried out on American Smelting and Refining Co. copper (99.999' percent Cu) by the present authors. Bars of this copper about 0.4 in. in diam and 12 in. long were prepared by vacuum melting and casting, followed by cold forging and swaging in several stages of about 40 pct reduction in area with intermediate recrystallization anneals. After the final anneal one bar was deformed in tension to 30 pct elongation; the gage length was then cut into several samples which were given axial compressions of various amounts. The hardness of

Jan 1, 1960

Draftsman and transitman for coal mine work in Middle West. Salary $125 per month. No. 277. Mechanical draftsman familiar with mill and machinery design for metallurgical and chemical plants. Advise experience, salary expected, and references. No. 289. Two cyanide shift bosses, one cyanide mill supt, and one assayer, for work in South America. Expenses clown and return if two year contract is made. No. 290. In assay laboratory of University in the Middle West, man to take charge of ore-dressing and. help in assay laboratory work. Willing to give right man assistant professorship. No. 291. Experienced appraisers familiar either with field or office methods, capable of field survey of the physical properties and able to check up their survey on the books of the company, which require a very intimate knowledge of accountancy. Salary $2000 to $2700. No. 292. Young man trained in chemistry and engineering to conduct experimental work on storage of coal. No. 293.

Jan 4, 1918

By AIME AIME

THE session* on Non-ferrous Metallurgy held Monday morning was conducted in a most satisfactory manner with F. F. Colcord, vice-president, U. S. Smelting Co., in the chair. In spite of the early hour and the fact that members desired to register first, the meeting started quite promptly, with almost every chair in the room occupied. About 65 men were present and during the morning many more came but, not being able to find room, drifted away to other fields of activity. The first paper presented, "Lead Refining Practice of the Bunker Hill Smelter of the Bunker Hill & Sullivan Mining & Concentrating Co.," by Alfred F. Beasley (T. P. 303), was read in abstract by Edward H. Robie, and an animated discussion followed in which Messrs. Johnson (written discussion), Brewer and Jones and Professor Hayward participated. The discussion hinged principally on the liquation of the zinc crusts, but Professor Hayward called attention to the fact that the practice of keeping the gold and silver crusts separate was not new and the present scheme illustrated the axiom that processes based on fundamental principles should not be considered as extinct; one can never tell when it may be found advantageous to make use of them again.

Jan 1, 1930

RECEIPTS [Magazine Advertising $ 62,564.83 Magazine Sales 3,591.44 Totalm 66,156.27 Dues, Arrears7,032.88 Dues. Current96,839.74 Dues, New Members6,525.00 Dues, in advance 1,907.02 Initiation Fees7,584.00. Sale of Transactions3,909.03 Sale of Binding7,845.05 Sale of Special Editions 338.20 Sale of Year Book76.20 Sale of Pamphlets1,189.06 Sale of Authors' Reprints867.54 Miscellaneous Receipts62.93 Interest on Bank Balances1,712.89 Interest on General Reserve Fund337.50 Interest on Life Membership Fund557.84 Interest on James Douglas Library Fund....5,491.89 Total Receipts$208,433.04] [ ]

Jan 1, 1925

By J. G. Baragwanath

CUBA'S lateritic iron ores, occurring on the northern coast of that island, though known to the Spaniards. did not receive any general attention until the close of the Spanish-American War. Preliminary studies of these deposits at that time indicated that the limonite contained small percentages of nickel and chrome, and it ryas subsequently discovered that although the average nickel content was only approximately 0.6 per certain limited areas of ore were suffiniently high in nickel to be considered commercial provided a suitable process fur its recovery could be developed. Early in 1937, Pardners Mines Corp. began a series of investigations which led to the development of such a process. Coincidentally, this company acquired option' on certain properties in the Levisa Bay and Moa Bay regions and conducted a systematic campaign of exploration by test pits and hand-auger holes in the course of which an aggregate of 90.000.000 tons of ore was developed in eight deposits.

Jan 1, 1945

By I. R. Kramer

Studies of the effect of size of the specimen on the change of slopes of Stages I and 11 by surface removal showed that the change of Stage I was independent of size with respect to the polishing rate; however, the change in the slope of Stage 11 with polishing rate increased directly in proportion to the surface area. The removal of the surface during the test affected the plastic deformation characteristics of gold, aluminum, and zinc single crystals and polycrystalline aluminum. The apparent activation energy of aluminum was found to be decreased markedly by removing the surface during the deformation process. In previous papers1-3 it was shown that the surface played an important role in the plastic deformation of metals. By removing the surface layers of a crystal of aluminum by electrolytic polishing during tensile deformation, it was found that the slopes of Stages I, II, and III were decreased and the extents of Stages I and II were increased when the rate of metal removal was increased. By removing a sufficient amount of the surface layer after a specimen had been deformed into the Stage I region, upon reloading, the flow stress was the same as the original critical resolved shear stress and the extent of Stage I was the same as if the specimen had not been deformed previously. The slope of Stage I was decreased 50 pct and that of Stage 11 decreased 25 pct when the rate of metal removal was 50 X 10"5 ipm. These data show that in Stage I the work hardening is controlled almost entirely by the surface conditions, while in Stages 11 and III both surface conditions and internal obstacles to dislocation motion are important. It appears that during the egress of dislocations from the crystal, a fraction of them becomes stuck or trapped in the surface regions and a layer of a high dislocation concentration is formed. This layer would not only impede the motion of dislocations, but would provide a barrier against which dislocations may pile up. In this case, there will be a stress, opposite to that of the applied stress, imposed on the dislocation source and dislocations moving in the region beyond this layer. It has been found convenient to refer to this layer as a "debris" layer. The "debris" layer may be similar to the dislocation tangle observed by thin-film electron microscope techniques.4 Reported in this paper are the results of studies on the effects of removing the surface during plastic deformation on aluminum crystals of various sizes. The effects of the surface on the yield point behavior of gold and high-purity aluminum crystals as well as the creep behavior were also determined. The effects of surface removal on polycrystalline aluminum (1100-0 and 7075-T6) are also reported. EXPERIMENTAL PROCEDURE For those portions of the investigation involving creep and tensile specimens, single crystals, having a 3-in. gage length and a nominal 1/8-in. sq cross section, were prepared by a modified Bridgman technique using a multiple-cavity graphite mold. The single crystals were prepared from materials which had initial purities of 99.997, 99.999, 99.999, and 99.999 pct for Al, Cu, Zn, and Au, respectively. The aluminum specimens for the size effect studies were prepared through the use of a three-tier mold in which crystals having a cross section of 1/8, 1/4, and 1/2 in. were grown from a common seed. The mold design was arranged so that one 1/2-in. crystal, two 1/4-in. crystals, and four 1/8-in, crystals of the same orientation could be cast. With this technique, it was possible to obtain only one set of crystals with the same orientation. Because of this limitation, it was not possible to determine both the changes of extent and slope of the various stages since a large number of crystals of the same orientation would have been required. Instead, only the change of slope as a function of the rate of metal removal was studied by abruptly altering the current density of the electrolytic polishing bath at various strains within the regions of Stages I and 11. The experimental techniques used for the tensile studies were essentially the same as those used previously.1,3 The specimens were deformed in a 200-lb Instron tensile machine, usually at a rate of 10-5 sec-5. A methyl alcohol-nitric acid solution was used as the polishing bath for aluminum. The temperature was maintained constant within ±0.l°C by means of a water bath. The tensile machine was

Jan 1, 1963

By Joseph W. Roe, L. L. HEWES

A GRAPHIC solution of Kutter's formula for the flow of water has been worked out By Dr. L. I. Helves in connection with his course in Graphic Computations, given in the Sheffieild Scientific School, Yale University, which may be of interest to those who deal with canals, flumes and streams.

May 1, 1909