Search Documents

UP TO and including 1931, the twelve mines that were treated in THE PORPHYRY COPPERS had produced 17.4 billion pounds of copper worth $2,820,000,000. With a little help from six others (three of them did not start output until 1954) that record had been increased at the end of 1955 to 60.5 billion pounds worth $10,440,000,000. Today, ten billion dollars is not as impressive as it once was; but it still represents a lot of value. It must be remembered that this is newly-created wealth, produced entirely from material considered worthless when the Porphyry era started about fifty years ago. At that time "rock" that contained less than forty pounds of copper per ton was regarded by competent mining engineers as value- less. It was not "ore" in the economic sense. Today, ore is being successfully exploited that contains less than twelve pounds of copper per ton. Also, in Peru, a typical Porphyry operation is being launched by a partnership of four United States mining companies that will involve an initial capital investment of $200,000,000 for mine development, plant construction, and the provision of related facilities. Of this project more will be said at the end of the chapter. The point I want to make now is twofold: (1) that phenomenal progress has been made in Porphyry engineering and technology; and (2) that exploitation of an important Porphyry copper deposit has become an industrial enterprise of truly great magnitude. Much had been accomplished by 1931; but that progress has been dwarfed by the achievements of the past 25 years- a fact that, in the nature of things, is as it should be.

Jan 1, 1957

By Lyon F. Terry

SPEED-UP of production of crude oil and its products, accompanied by rising prices and the organization of the industry on a war basis, featured the economic aspects of petroleum in 1941. Early in the year American tankers were urgently requested by the British to replace losses and offset slower transit under convoy. Some forty American owned tankers were first assigned to Britain and an additional forty-odd ships were transferred during the summer. This threatened to reduce our transportation facilities from Gulf ports to the Eastern seaboard below requirements, especially should sinkings have increased and the British needed more ships. Co-ordinator Ickes began preparations for restricting gasoline consumption in the Eastern district and plans were formulated for the construction of an emergency trunk pipe line from Texas to New York and Philadelphia refining centers, and for a gigantic tanker-building program. Sales of new oil-heating units in the East practically ceased. The companies were urged to transport as much oil as possible by tank car and by October 140,000 barrels of oil per day were reaching the East Coast district by rail, sufficient to meet 8 per cent of total requirements. But British sinkings from July through October decreased 63 per cent compared with the four months ended June 30, Britain began the return of tankers, the construction plans were dropped, and the threatened shortage was thus averted.

Jan 1, 1942

By Milton F. Goodrich

The idea of using water-only cyclones to scalp clean coal from the feed to other devices has recently been gaining in popularity. 1,2,6 An indication of this popularity is that water-only cyclone scalping is already employed in a few commercial plants. Water-only cyclones scalp the feed to a heavy media vessel in the Warwick plant,3 to Deister tables in the Rowland plant,4 and to a heavy media cyclone circuit in the Amherst Coal Company's McGregor plant.5 Despite this trend, we found surprisingly little information in the literature on the performance of water-only cyclone scalping. Therefore, we undertook a study of its technical merits, limiting our investigation to a water-only cyclone scalper in conjunction with heavy-media cyclones. We felt this to be a reasonable combination of equipment, since both processes operate well on the same size coal. First, we developed simple mathematical relationships revealing general characteristics of the system. Next, we compared the clean coal yield and quality obtainable by the system on four different coals with that obtainable by heavymedia cyclone circuit alone and water-only cyclones middlings recirculation circuit alone. This was done by using computer program to simulate the operation of the three systems. Finally, we considered the effect that implementation of the system would have on a typical preparation plant circuit. The System The system chosen for study [(shown schematically in Fig. 1)] comprises two stages: a primary stage (PI) consisting of water-only cyclones, and a secondary stage (P2) consisting of heavy media cyclones. The water-only cyclones separate raw coal at a low specific gravity, producing a relatively small amount of high quality clean coal and a refuse containing much good coal. This refuse is then recleaned in the secondary stage, where the sharper separation of heavy media cyclones, operated at a higher specific gravity, reclaims additional clean coal. Finally, the clean coal from both stages is combined as the system's clean coal, while the refuse from the secondary stage becomes the system's refuse output. Theoretical Analysis Two assumptions lie behind the following theoretical analysis. The first assumption is that partition curves can represent not only the performance of each stage but also the performance of the system as a whole. These curves show partition number as a function of specific gravity, where partition number is either the percent or fraction of a raw coal with a given specific gravity reporting to clean coal. The second assumption is that these curves are independent of the raw coal characteristics. At any specific gravity the system's partition number is solely a function of the partition numbers of each stage. For convenience, we use the following variables in describing this relationship: g = specific gravity, PS(g) = the partition number of the system at specific gravity g, P1(g) = the partition number of the primary stage at specific gravity g, P2(g) = the partition number of the secondary stage at a specific gravity g. For this system, we can show algebraically that the relationship is: [Ps (g) = PI (g) + (1- P1(g)) P2 (9)(1)] With this equation the system's partition curve can be determined if the partition curves of each stage are known. By definition, the partition numbers P1(g) and P2(g) must each be less than, or equal to, one. Placing these constraints on Eq. (1), we arrive at the relations: [Ps(g) % P1(g) and Ps(g) % P2(g)(2)] Thus, at any specific gravity the system's partition number is always greater than that of both stages. [Figure 2] shows typical partition curves. Curve I represents the primary stage, which consists of water-only cyclones operating at a separating gravity of 1.3. (The separating gravity or the

Jan 1, 1979

By W. P. Barba

IN THE early summer of 1917, it became evident that the then existing sources of supply of guns and gun forgings were totally inadequate for the enormous and rapidly growing requirements of the Ordnance Department of the Army, so arrangements were made with sixteen makers of other products to take up the manufacture of guns and gun forgings. Nine of these makers were required to produce their own steel from the raw materials and convert it into rough machined gun forgings; the others finished and assembled these forgings into completed guns. In December, 1914, four of these makers of steel and rough gun forgings were instructed to manufacture the same amount of the 6-in. and 9.5-in. guns and howitzers. It, therefore, seemed practical .and profitable to assemble these makers into a small group, together with the officers of the Ordnance Department, and provide standard 'equipment in each of the four works for the production of these two types of guns. The advantages of this cooperation were immediately manifested, and there commenced an interchange of shop practice and a free discussion of facilities and methods that covered not only the equipment but the manufacturing processes.

Jan 1, 1920

By T. I Harkins, J. Brian Eby

This paper outlines the geophysical investigation of the area covering the Darrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The Darrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook1 and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outline and comes to within about 4625 ft. of the surface. At this depth the diameter of the salt plug is approximately 4800 ft. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The line showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable. Surveys with Refraction Seishograph and Torsion Balance A reported oil show in a water well drew attention to the lands of the Belle Helene

Jan 1, 1943

By J. Brian Eby, T. I. Harkins

This paper outlines the geophysical investigation of the area covering the Darrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The Darrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook1 and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outline and comes to within about 4625 ft. of the surface. At this depth the diameter of the salt plug is approximately 4800 ft. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The line showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable. Surveys with Refraction Seishograph and Torsion Balance A reported oil show in a water well drew attention to the lands of the Belle Helene

Jan 1, 1943

By AIME AIME

A REGULAR meeting of the Executive Board 'of American Engineering Council was held in the Onondaga Hotel, Syracuse, N.. Y., Feb. 14, 1921, with the president, Herbert Hoover, presiding. Reports of committees were presented and acted upon as follows: ENGINEER ON INTERSTATE COMMERCE COMMISSION The second meeting of the Committee was. called because it was represented to the Committee' on Pro¬cedure that the American Society of Civil Engineers, the American Association of Engineers, and the Ameri¬can Institute of Consulting Engineers were anxious to have President-elect Harding appoint an engineer to fill one of the vacancies on the Interstate Commerce Commission. The representative of The American Society of Civil Engineers agreed to endorse the recom¬mendations- of American Engineering Council, and the Committee on Procedure prepared and sent a letter to the President-elect, a - copy of this letter being sent to each member of the Board. No names were suggested. . The appointment of an engineer on the Interstate Commerce Commission was approved and the Board, after approving the action of the Committee 'on Procedure in writing the President-elect, voted that, if requested, the Committee on Procedure submit a list of not less than six names for the appointment of an engineer on the Interstate. Commerce Commission.

Jan 1, 1921

Swedish mining companies are noted for their excellence in underground mining practice, and this classification certainly has to be applied to their design of crushing plants also. All these mines are highly mechanized with either rail or truck haulage, and typical examples of underground crushing plants designed for each of these haulage practices are presented here. Almost all the primary breakers are of the overhead eccentric, single- toggle jaw crusher type with units as large as 55 by 71 in. (1400 by 1800 mm) being used. In contrast to North America, where jaw crushers are almost always preceded by apron or vibrating feeders, many of the. Swedish crushers are choke fed with the dump pocket being located directly above the crusher. This practice results both from excellent knowledge of the ore characteristics and the ability of the overhead eccentric crusher to also act as a feeder. An excellent example of a crushing plant of this design is shown by the sketch of the LKAB Alliansen Crusher No. 64 at Malmberget, Sweden. Forty-six st (42 mt) trucks dump magnetite ore into a 91.6 cu yd (70 m3) dump pocket mounted over a 55 by 71 in (1400 by 1800 mm) Morgards- hammar overhead eccentric crusher using a 180 hp (132 kw) motor and belt drive. Crushed ore at 10 in. (250 mm) size drops onto an air- operated tipping chute which diverts the ore to either of two 1962 cu yd (1500 m3) pockets equipped with 3 ft 11 in. by 7 ft 11 in. (1200 by 2000 mm) Schenk vibrating feeders. Dust is drawn into a wet scrubber and exhaust air is combined with mine exhaust air. Because the crusher must be assembled underground, a 45/5 ton crane is installed over the crushing installation. A crusher above ground such as at Sacaton can easily utilize a smaller crane. Capacity of this 'most interesting crushing installation is 1653 st (1500 mtph) .

Jan 1, 1978

By J. George Gregr

INTRODUCTION This part contains field case studies of typical mishaps, accidents, equipment damage or post installation failures resulting from mistakes in design, manufacturing and construction, as well as improper storage, handling and installation procedures of the equipment covered in Part 1. GENERAL Certain mistakes are repeated and common rules violated on almost all industrial equipment installations, with the inevitable consequences of additional cost, construction delays and aggravation of all parties involved. The most common failures are in the following areas: Cleanliness of all components during installation and later in operation. Adherance to manufacturer' s recommendations and tolerances for equipment installation. Comprehensive, properly identified installation and maintenance records. Handling of the components. Adequate tooling and auxiliary equipment in working order. An inoperable hydraulic power unit for torque wrench or for jacking of the mill, or faulty crane can be a very costly proposition. A special area in comminution circuits are wear components. Apart from the mill liners, the wear components such as, feed chutes, rock boxes, mill trunnion liners, discharge sumps, etc. are designed to the best theoretical configuration, based on experiences in similar installations. However, each process is different to a various degree, mainly because of various types of ores and grinding requirements. Consequently the first generation of wear components is very seldom the ideal one. Based on operational experience, the shape and material of wear components should be modified, until the optimum, most economical design is achieved. SHIPPING AND STORAGE Considerable damage to the equipment can be done by careless packing, shipping or storage.

Jan 1, 1982

By Granville S. Borden

MANY complaints have been filed by mine prospectors, explorers and producers about inequities in mining taxation. They have insisted upon improvement, and in the past 35 years there has been some progress. Many of the best taxation provisions made to date are those contained in the Revenue Act of 1951. Mining economics presents special problems, a fact even recognized by many textbooks. Certain provisions have been made to take care of mining taxation rights, but these have been made by Congressional act and do not represent basic, constitutional, guarantees. Despite special provision, in the form of depletion allowances, there remain injustices. The industry faces the problem of gaining adequate income tax allowances for exploration and development expenditures, operating losses, and bonus and subsidy payments. Problems in mine taxation arose soon after the adoption of the 16th Amendment. This amendment gave Congress the power to impose income taxes. Supreme Court decisions against a number of mining companies held that Congress, under its power to tax income, could tax net operating revenue before depletion allowance was deducted. The court also ruled that the right to deduct depletion is a matter of Congressional permission. There is no statute provision permitting mining stockholders to recover their investment out of dividends while the mine is being operated. The Supreme Court did not recognize that part of mining proceeds are actually amortization of the cost of mineral rights. Both these omissions stem from failure to recognize that by its very nature mining consumes its mineral rights and therefore that a part of gross proceeds are not income but recovery of capital. Suppose a Congress unfriendly to mining interests repeals the provisions that allow deductions for depletion. Under such a situation assume that a corporation buys a mineral deposit for $300,000. They mine the deposit and earn an operating profit of $500,000. At the current rates they would pay a Federal Income tax of in excess of $250,000. This venture results in a loss of $50,000 as shown in the table below. For the example given the absence of depletion provisions in income tax law would turn ore into waste rock, because the word "ore" connotes commercially mineable rock. [ ] In retrospect the conclusion is clear: If the Supreme Court had recognized that a part of mining proceeds represent in reality sales proceeds of mineral rights, then profits derived from such sales would have been taxed at the favorable long-term capital rates, instead of being taxed at the high normal, surtax and excess profits rates. It is a question whether percentage depletion allowances offset this tax situation. History The history of depletion allowances has been one of general improvement. The original act did not include depletion, but an allowance at the rate of 5 pct of gross proceeds was provided in 1913. The Acts of 1916 and 1917 allowed depletion upon cost of property, and in 1918 the law was further changed to permit depletion upon cost, or market value as of date of discovery. In 1932 metal, coal and sulphur properties were permitted to elect depletion in percentages of gross income, limited to 50 pct of net income, in lieu of cost depletion. Shortly thereafter the rule was changed and percentage depletion is now allowable in any case where it is higher than cost depletion. Since 1942 percentage depletion allowances have been extended to cover many nonmetals, and in 1951 the rate for coal mines was increased from 5 to 10 pct of gross income. It is interesting to note that these allowances have been retained, and even

Jan 1, 1952

By E. Gaujot

IN connection with the question of coal waste and economy in mining, we would call the attention of those interested to an apparatus invented by M. Dernencourt, Superintendent of the Anzin Division of the Anzin Coal Company, North of France. This apparatus is known in France and Belgium under the name of prop screw jack (vis botte), and has been used with good results in the above-named countries for some years past. M. Ponson gives, in his " Traité de l'exploitation des Mines," a description of it (page 533), but as the description given is old, the work not widely known in this country, and as some valuable improvements have been made since, I thought it might be useful to give a description of it, having seen it in operation in 1867, while in Europe to attend the great Exposition, and on a scientific tour to the mining districts of France, Germany, Belgium, and Italy. The prop screw jack is composed of the following pieces: I. The body or column B, Fig. 4 [Plate (1)], of oak or yellow pine, sawed square, the bark taken off, and any length, proportionate to the vein. The smallest are 10 inches diameter at the base, and 9 inches at the top, the height being from 12 to 15 inches less than the size of the vein. In the axis of this column, and at the top end, is a cylindrical opening or hole, C, 2 3/4 inches diameter, 10 inches deep, for the screw, S. II. Two wrought-iron rings, R R, to strengthen the two extremities of the column ; the rings must be put on hot. III. A cast-iron washer, E, with hole in centre a little larger than the screw, to be put on the top of the column, and on which the nut is to rest; the top side of this washer must be faced on the lathe, also the bottom of the nut, to prevent friction. IV. The screw, S, having a total length of 12 inches and a diameter of 21/2 inches (for very high veins this diameter may be in¬creased to 3 inches), and has on its top a wrought-iron plate, T,

Jan 1, 1873

By Ernest P. Hall

At the SME Fall Meeting held in Phoenix, Ariz. last October, Ernest P. Hall, addressing an Air and Water Pollution session, noted that water pollution caused by acid drainage from bituminous coal measures had begun long before recorded history. "Until recently," he said, "man did not begin to understand the physical phenomena which took place to cause [it] and even today he does not know what can be done to prevent it." CAUSES "It is known from the reports of early explorers that drainage from bituminous coal measures was causing water pollution before coal mines were opened on this continent. They noted the nature of the polluted water in the runs and creeks and predicted the presence of substantial deposits of coal based on the appearance and character of the water. Even today, polluted water drains from virgin coal areas which have not been touched by mining machines," Mr. Hall said.

Jan 1, 1966

By R. A. Graham, R. W. Rohde, J. R. Holland

In a shock wave compression study of a martensitic Fe-30 pct Ni alloy, Graham, Anderson, and Holland' found a region of unusual compressibility extending from a few kilobars up to about 20 kbars. This region was characterized by a continuously decreasing shock wave velocity with increasing stress. In this note, we report the results of a study initiated to determine the source of this unusual compressibility. In earlier shock-loading experiments on martensitic Fe-30 pct Ni, Loree et a1.' determined that a phase change occurred at about 80 kbars. Subsequently, Bowden and elly found that samples of a similar material shock-loaded at about 100 kbars experienced a martensite-to-austenite transition. Their crystal-lographic analysis showed the transition was a direct reversal of the established martensite system to the austenite phase. The shock loading in the present experiments was accomplished by precisely controlled plane impact between two discs of the sample material. This configuration created a state of uniaxial strain in the two the front of a projectile which was accelerated to various velocities. Planarity between the impacting discs was controlled to 5 x 10-4 rad, and impact velocities were measured to 0.5 pct. From a knowledge of the Hugoniot relationships of the material and the impact velocity, the shock-wave stress can be calculated. Samples were shocked at 18, 50, 70, and 100 kbars. The specimen discs shocked at 18 and 50 kbars were instrumented with quartz gages to observe the stress time profile. A more detailed description of the experiment has been given previously.4 The shock-loaded specimens were recovered intact by decelerating them in a catcher filled with soft wood. Discs of Fe-30 pct Ni nominally 12.7 mm thick and 64 mm in diam were cut from bar stock. Chemical analysis of the material provided the following composition in weight percents: 29.5 Ni, 0.50 Mn, 0.21 Si, and 0.10 C, with traces of Cr, Cu, Mo, Al, and Co. The discs were austenitized at 650° C for 2 hr at a pressure of less than l0-' torr, and furnace-cooled. Martensite was then produced by quenching the discs at -196" and holding 168 hr. The initial martensitic structure formed is shown in Fig. l(a). Typical microstructures of samples shock-loaded at 18 and 100 kbars are shown in Figs. l(b) and l(c). The banded structure with the austenite regions running parallel to the shock propagation direction was characteristic of samples shock-loaded at all stresses. No such banding was found in samples that were not shock-loaded. Comparison of Figs. l(b) and l(c) shows that, although under the optical microscope the two microstructures are quite similar, the martensite plates of the specimen shocked at 100 kbars etched in a distinctly different manner. This unique etching behavior of martensite in samples shock-loaded above the 80 kbar transition point has also been observed by Leslie el al.' These investigators determined from X-ray and electron microscope studies that fcc martensite, similar in appearance to normal bcc martensite, had been formed under shock loading. A quantitative determination of the amount of austenite present after shock loading was made by X-ray techniques. Both the methods of Lindren' and Miller' were utilized. The results are shown in Table I. The error limits are those experimentally observed from two independent analyses of each sample and represent the precision of the experiment. The absolute error, which should be similar for each sample, is believed to be about 10 pct. It is seen that as the shock stress increases the amount of austenite present also increases. On the basis of the X-ray and microscopic observations, we conclude that shock loading below the 80 kbar ersal will initiate a martensitic reversal: the amount of reversal that occurs increases with in-

Jan 1, 1969

and would also contribute to the post-war employment. -As far as the future is concerned, I doubt whether any of the present geophysical methods will ever be developed to directly indicate ore. However, the geochemical methods and certain combinations between chemical and geological methods now used might be the answer to our prayers for direct and more definite methods of determining the quality of the ore or its relative metal content. Geochemical and spectrochemical analysis of minute content in ground waters, in soil or in plants and trees, living or dead, will be extremely important and I would venture to predict that in the very near future each mining or exploration company and each assay oflice will have its own spectroscope equipped for accurate chemical analysis, not only to guide the daily work in the mine, but also for identifying ores as well as for guiding exploration, geological mapping and the evaluation of geophysical indications. These methods, although they are still in their infancy, promise very much for the future. Radioactivity methods could also be helpful when sufficient facilities for radioactivity determination can be made available. They have already been used to a great extent in oil exploration and experiments have shomn great promise for ore exploration also. As for future surveys of large areas, the exploration for physical contrasts will be made from the air, using aeroplanes, helicopters, etc. Already electrical and magnetic methods have been designed whereby the instruments are carried in the aircraft and by automatic recording the location of anomalies is made in a simple enough manner. It should be possible in this way to cover, say, a square mile in an hour. Later Discussion Replies to Dr Lundberg. J. B. Macelwane.*—Someone has said that if a person knows his subject well enough he can explain it in words of one syllable. The point is well taken and I think the converse is also true. If a person cannot explain a subject clearly in simple words, it is either because he has not sufficient command of the language, or he is not master of his subject. Now it is obvious, it seems to me, that the remedy for both of these unfortunate conditions lies not in less education, but in more. If Dr. Lundberg has met geophysicists who confused and discouraged prospective clients by their inability to talk the language of the mine owner or of the mining engineer or geologist, the fault most probably lay in the geophysicist's lack of sufficient training; but it may also have been the want of ordinary common sense, which no amount of education can supply. It is hard to understand the position taken by Dr. Lundberg. Does he regret his own extensive training? noes he wish to say that he would have had greater success in geophysics if he had been only a mine hand with an instrument and a rule of thumb? As a matter of fact, I find it rather difficult to account for his presentation before this Committee on Geophysics of an emotionally distorted picture of the Report of the Committee on Geophysical Education, after the lapse of an entire year since the Report was read and discussed in its proper place, unless he honestly thinks he is handicapped by his knowledge and training and wishes to warn the whole profession against a similar fate. I regret that I am obliged to disagree so emphatically with Dr. Lundberg's thesis— but I believe it would be dangerous if left unchallenged, both because of the inaccurate statements it contains concerning the recommendations made in the Report and because of the ultimate discredit that would be bound to fall upon genuine geophysics if Dr. Lundberg's recommendations were extensively followed out. S. F. Kelly.*-—The argument that a science and its practitioners can be improved by debasing the standard of educational preparation is indeed a strange argument to come from the pen of a man with the education of Dr. Hans Lundberg. In criticising the Committee report, moreover, he has to a certain extent set up a straw man to belabor. The statement that the Committee report recommends that

Jan 1, 1946

and would also contribute to the post-war employment. -As far as the future is concerned, I doubt whether any of the present geophysical methods will ever be developed to directly indicate ore. However, the geochemical methods and certain combinations between chemical and geological methods now used might be the answer to our prayers for direct and more definite methods of determining the quality of the ore or its relative metal content. Geochemical and spectrochemical analysis of minute content in ground waters, in soil or in plants and trees, living or dead, will be extremely important and I would venture to predict that in the very near future each mining or exploration company and each assay oflice will have its own spectroscope equipped for accurate chemical analysis, not only to guide the daily work in the mine, but also for identifying ores as well as for guiding exploration, geological mapping and the evaluation of geophysical indications. These methods, although they are still in their infancy, promise very much for the future. Radioactivity methods could also be helpful when sufficient facilities for radioactivity determination can be made available. They have already been used to a great extent in oil exploration and experiments have shomn great promise for ore exploration also. As for future surveys of large areas, the exploration for physical contrasts will be made from the air, using aeroplanes, helicopters, etc. Already electrical and magnetic methods have been designed whereby the instruments are carried in the aircraft and by automatic recording the location of anomalies is made in a simple enough manner. It should be possible in this way to cover, say, a square mile in an hour. Later Discussion Replies to Dr Lundberg. J. B. Macelwane.*—Someone has said that if a person knows his subject well enough he can explain it in words of one syllable. The point is well taken and I think the converse is also true. If a person cannot explain a subject clearly in simple words, it is either because he has not sufficient command of the language, or he is not master of his subject. Now it is obvious, it seems to me, that the remedy for both of these unfortunate conditions lies not in less education, but in more. If Dr. Lundberg has met geophysicists who confused and discouraged prospective clients by their inability to talk the language of the mine owner or of the mining engineer or geologist, the fault most probably lay in the geophysicist's lack of sufficient training; but it may also have been the want of ordinary common sense, which no amount of education can supply. It is hard to understand the position taken by Dr. Lundberg. Does he regret his own extensive training? noes he wish to say that he would have had greater success in geophysics if he had been only a mine hand with an instrument and a rule of thumb? As a matter of fact, I find it rather difficult to account for his presentation before this Committee on Geophysics of an emotionally distorted picture of the Report of the Committee on Geophysical Education, after the lapse of an entire year since the Report was read and discussed in its proper place, unless he honestly thinks he is handicapped by his knowledge and training and wishes to warn the whole profession against a similar fate. I regret that I am obliged to disagree so emphatically with Dr. Lundberg's thesis— but I believe it would be dangerous if left unchallenged, both because of the inaccurate statements it contains concerning the recommendations made in the Report and because of the ultimate discredit that would be bound to fall upon genuine geophysics if Dr. Lundberg's recommendations were extensively followed out. S. F. Kelly.*-—The argument that a science and its practitioners can be improved by debasing the standard of educational preparation is indeed a strange argument to come from the pen of a man with the education of Dr. Hans Lundberg. In criticising the Committee report, moreover, he has to a certain extent set up a straw man to belabor. The statement that the Committee report recommends that

Jan 1, 1946

By J. T. Norton, N. J. Grant, A. M. Gervais

An investigation of the creep deformation of coarse grained specimens of high purity aluminum in the temperature range 800' to 1150°F, permitted the formulation of a theory explaining the formation of kink bands. The X-ray Laue back-reflection technique was used in conjunction with metallographic studies to determine the crystallographic elements involved in kinking and to measure the rotations of the bands. THAT metals deform by the formation of kink bands was first shown by Orowan1 in 1942. He manually compressed cadmium single-crystal wires, the basal planes of which were parallel to the wire axis and to the direction of compression. He found that kink bands formed quite suddenly. Similar experiments were performed by Hess and Barrett2 on zinc with a hydraulic testing machine to permit slower more careful compression. They observed that kink bands formed progressively with increasing compression. Recently Washburn and Parker3 observed the formation of kink bands in zinc single-crystal specimens during tension creep experiments. Each of these authors observed the formation of kink bands but did not make a complete analyses of the crystallographic relationships. In addition to these studies on hexagonal metals, extensive investigations of kink bands formed during deformation of aluminum in tension at room temperature have been reported. Two types of deformation bands have been observed during the deformation of aluminum at room temperature. These are: 1—kink bands: these exhibit a sharp curvature of the lattice along certain surfaces, and 2—bands formed by secondary slip along certain regions. As has already been shown by Honeycombe,4 it is important to point out the difference characterizing the two types of deformation bands. In the first case. for moderate deformation, only one system of slip planes normally is active; in the second case, however, two slip systems are active in the deformation bands. The latter have a rumpled surface because of the action of the two slip systems. In the present work only the first type of band was studied and to avoid any confusion the term kink band will be used exclusively in the discussion which follows. Honeycombe' observed that very narrow kink bands (width, 0.01 mm) formed along the (110) planes during the deformation of high purity aluminum at room temperature. He observed narrower ones in commercially pure aluminum and found also that their width decreased with decreasing temperatures. Chen and Mathewson5 reported the formation of kink bands during tensile testing of single crystals of high purity aluminum at room temperature and pointed out that some rotation occurred about a [211] direction. The influence of the bending moment on the formation of kink bands was illustrated by the experiments of Rohm and Kochendorferl0 who used a Polanyi apparatus to obtain pure shear during tensile testing of high purity aluminum single crystals. Under such conditions only one slip system was active and no kink bands were observed; consequently, no noticeable asterism was detected after deformation. The influence of the bending moment will be discussed later. Calnan8 gave a detailed account of the work performed on kink bands obtained during deformation of aluminum at room temperature. Because no explanation of the process of kink band formation in creep was given in the previous investigations and because some of the above observations are vital to the following discussion the brief review of the literature has been given. It is proposed in the present work to provide an explanation of kink band formation during creep deformation at elevated temperatures. Results and Discussion Kink bands were observed to form during tensile creep testing of high purity (99.995 pct) aluminum specimens, having a very large grain size, in the temperature range 800" to 1150°F. These observations were made in grains which occupied the whole cross section of the specimen. The specimens were originally round (diameter, 0.187 in.; gage length, 1 in.) and had parallel flats milled to permit easier metallographic and X-ray observations. The final

Jan 1, 1954

By AIME AIME

SOMETIMES family backgrounds have a deep, if not direct, influence on a man's lifework. Dean Callen's paternal grandfather came from Wales and was a mine official in the Pennsylvania anthracite field: his maternal grandfather was a retail coal dealer. His father and uncle began their careers a. breaker boys but later completed their educational work and ended up in the professions. With that background, and with the slate region ( Pen Argyl, Pa.. July 1;. 1888) as his birthplace it is not strange that "Cope" Callen became a teacher of mining engineering. Graduating from Lehigh with an E.M. in 1909, lie taught there for two years while working for his master's degree. In 1911 he returned to teaching, going to the University of Illinois as instructor in mining engineering. In 1917, he was called to West Virginia University as head of the department of mining engineering and director of mining extension. The extension work was about dead. bus a new staff was built and the six-weeks' short course in coal mining was revamped into an attractive and efficient course which has grown in popularity with the years. Callen's work attracted the attention of the Federal Board for Vocational Education and in 1919 he was invited to serve that board as special agent for mining, taking a six-months' leave front the University.

Jan 1, 1944

By A. J. Miles, A. D. Topping

in this paper, the theory of elasticity has been applied to the rock about a deep well, It is assumed that the rock has a modulus of . elasticity and a Poisson's ratio and that the theory of elasticity applies. It is necessary to know or assume the state of stress existing in the rock before it is penetrated by the well drill. The application of this theory indicates that stress concentration of shear, tensions, and compressions about the bore hole are of a high order. This is particularly true when a horizontal compressive stress exists in one direction only in the formation before drilling. If such an initial state of stress exists before drilling, then the rock will have stress concentrations of both tension and compression at the same elevation and of such magnitude that failure of the rock is likely. Accompanying these is a shearing stress of large proportion which is likely to produce spalling of the well walls. Internal pressure applied to the well bore will relieve the extreme compression but not the tension and has little effect upon the shear. Plastic deformation of the rock through a geological time tends to mitigate the stress concentrations. IntroductioN It has long been known that the stresses about holes and re-entrant corners of elastic solids under the influence of loads are different and generally more intense than those imposed upon the body else- where. Stress concentration at a re-entrant corner can be reduced by increasing the radius of the fillet at the corner. Stress concentration at the end of a crack in a plate undergoing either tension or compression Can be relieved appreciably by drilling a hole at the very end of the crack. Also, stresses can be increased in an elastic body in tension or compression by making a hole in it. The stress concentration is greatest at the edge of the hole. Considerable knowledge of the stresses which exist about the bore hole of a deep well may be had by applying our knowledge of engineering mechanics; or more particularly the theory of elasticity. It is, of course, necessary to make the assumption that the rock is elastic and behaves as an elastic solid, that is, that it obeys Hooke's law, has a modulus of elasticity, and a Poisson's ratio. It is also necessary to know, Or assume, the state of stress which exists in the rock prior to the penetration of the drill. With this knowledge it is possible to compute the stresses about the bore hole. The problem can be simplified by considering several simple cases separately and then by applying the principle of superposition to solve the more complex cases which are made up of the simpler ones. Case i—Rock Strata in Compression Penetrated by a Hole This case was first worked out by G. Kirsch* for structural material, but applies equally well to a horizontal rock strata in a state of in in one direction

Jan 1, 1949

By Ivor Hawkes

A wide variety of borehole gages have been developed for measuring rock stress. They all operate on the principle that stress changes around a borehole result in deformation that can be measured by the gage and interpreted in terms of the stress change either by calculation or calibration. In general terms, gages that comply with the borehole deformations are referred to as “deformation meters” and those that restrain the deformations by reason of their rigidity are referred to as “stress meters.” The main advantages claimed for stress meters are: their “stress” sensitivity is much less dependent on the rock modulus than that of deformation meters, and they are clamped firmly in the borehole. The use of each of the borehole gages developed for stress determinations in rock in the main has been confined to the laboratory responsible for its development. To be generally accepted a gage must meet the following specifications : 1) Gages to be left in place to measure stress changes must be relatively cheap, and if possible recoverable, so that large numbers can be used to obtain an overall picture of the changing conditions. This, of course, is not necessarily the case for recoverable gages designed for absolute rock stress measurements where usually only one or two gages are involved. 2) For use in the adverse environmental conditions encountered underground, it is essential that gages be robust, stable, and unaffected by high humidity, corrosive water, or dust. 3) Highly qualified technicians are rarely employed specifically for rock mechanics studies in mines or on civil engineering sites and there- fore gages designed for measuring stress changes must be easy to set and

Jan 1, 1972

By R. Schuhmann

Available thermodynamic data applicable to copper smelting systems are collected and tabulated, and the important gaps are pointed out. A few examples are given of estimations which can be made from the available data. An experimental research program is proposed to supply the thermodynamic data that appear most essential to better quantitative understanding of the chemistry of copper smelting. The proposed program is designed also to shed specific light on the practical problems of slag losses and magnetite behavior. OPPER smelting, from flotation concentrates to V-/ blister copper, is conspicuous among the large scale chemical processes which are conducted with only relatively incomplete knowledge of the physical chemistry involved. For example, no common metallurgy text explains adequately why copper enters the matte phase while iron enters only to the extent that sulphur is left over after satisfying the copper. Explaining this important phenomenon as a manifestation of the greater affinity of sulphur for copper than for iron is unsound because the affinities of copper and iron for sulphur are about the same at smelting temperatures. As will be shown, other affinities are really decisive in the relatively clear-cut separation of copper in the matte. In contrast, thermodynamic studies have contributed much to our understanding of copper refining, zinc oxide reduction, magnesium production, steelmaking, etc. For each of these processes, the important reactions are clearly recognized, and fair to good quantitative values of the free-energy changes and equilibrium constants are available. Such data have proved to be of constantly increasing practical value in process development and improvement. Work in other fields has furnished much thermodynamic data applicable to copper smelting systems. In fact, several promising starts have been made in applying such data to specific smelting problems. Kelleyl made an appraisal of the possibilities of recovering elementary sulphur from low grade matte. His calculations and compilations of thermodynamic data have represented the starting point for much of the work in this field, including the present survey. Huang and Hayward2 nd Aksoy3 used thermodynamic methods in the study of copper losses in reverberatory slags. Peretti4 used thermodynamic data in explaining the chemistry of converting. The recent publications of Darken and Gurry"." and of Darken,' dealing with the iron-oxygen and iron-silicon-oxygen systems, respectively, present equilibrium data that are applicable to copper smelting systems. Also additional data were reported recently on the affinity of sulphur for copper, manganese, and iron8 and on the sulphur pressures of iron-sulphur melts." The survey presented in this paper was made as the basis for planning an experimental program on the thermodynamics of copper smelting. Few researches on the chemistry of copper smelting have been reported in recent years, so that a reappraisal and coordination of old and new data are essential if further work is to take the directions of maximum value. The experimental program is now in progress, and the plan of attack is outlined at the end of this paper. Progressive Oxidation and Desulphurization of Copper-bearing Liquid Phases: The chemical activities of sulphur and oxygen are two of the most important thermodynamic yardsticks to be applied to copper smelting processes. Virtually the entire smelting and refining sequence involves a series of systems characterized by decreasing sulphur activity and increasing oxygen activity. In this section, therefore, an attempt is made to define and explain these activities in terms of equilibrium partial pressures of SO2, s2, and O,. Also, estimates of these quantities are presented, the estimates being based largely on calculations presented in a later section of this paper. The sequence of steps from raw flotation concentrate to fully oxidized copper ready for poling involves progressive and controlled oxidation. Iron is oxidized and enters the slag. Sulphur is oxidized and leaves in the gas. Table I summarizes several important features of this oxidation and desulphurization sequence, starting at the beginning of the matte blow in the converter. The top line gives in order the principal smelting and refining stages up to fully oxidized copper, plus the additional step, not used commercially, of oxidizing all the way to Cu,O. In the second line are shown the principal copper-bearing liquid phases which characterize the process. Through most of the sequence the copper

Jan 1, 1951