Search Documents

By D. W. Fuerstenau, L. M. Berlioz

In 1957, Charles1 first presented an analysis of a relationship between the energy expended in comminution and the extent of size reduction achieved. Subsequently, Schuhmann extended and interpreted Charles' approach to comminution. According to their analysis, the energy, E, expended in comminuting unit mass of fairly uniformly-sized material is related to the size modulus of the product, k, by where a is the distribution modulus (slope of the log-log cumulative size distribution plot) and C is a constant, which is primarily determined by properties of the solid. If there is any fundamental basis for the E vs k relationship, E must necessarily be concerned with the useful work for the size reduction process and not necessarily the work input, as discussed in detail by Harris.3 Charles and numerous other investigators tested this equation only by relating k to the grinding time, assuming expended energy to be directly proportional to time, but never directly measuring power. In our laboratories, we recently constructed a special batch ball mill with which the power could be accurately determined with torque measuring apparatus.4 With this device, a direct test of the Charles relationship could then be made for ball milling. 5 EXPERIMENTAL A stainless steel mill, 11.5 in. long and 10 in. in inside diam, lined with eight low-silhouette lifter bars, was used for these experiments. The grinding media consisted of 30 kg of single sized, 1-in. diam, stainless steel balls, which occupied about 50% of the total mill volume under static conditions. The void fraction of the static ball load was approximately 0.4, and for the dry grinding conditions used, the corresponding interstitial volume was filled when about 3300 g of the dolomite feed material was present. The 7x9 mesh dolomite used as feed was obtained as a natural, uncrushed product thus as- suring a random distribution of feed particle shapes. Charge weights of 660, 1320, 1980, 2480, 3300, 3960 and 5280 g, which correspond to 20%, 40%, 60%, 80%, l00%, 120%, and 160% of the interstitial load, respectively, were used. Grinding times of 20, 40, 60, 80, 100, 150, 200 and 300 revolutions were considered, with the mill operating at 54 rpm (approximately 60% of critical speed). The tests were made sequentially, in that the size distribution obtained after a certain grinding interval was utilized as the feed for the subsequent period of grinding. Agreement with control experiments where the mill ran continuously for the entire interval was excellent. Torque measurements were made utilizing a Baldwin-Lima-Hamilton SR-4 torque pickup in the manner that has been described previously.3 Standard wet (to obtain the -400 mesh material) and dry sieving procedures were followed using the Tyler full screen series. RESULTS The Gaudin-Schuhmann size distributions obtained in all of these experiments are characterized by distribution moduli (slopes), a, of about 0.66 and are representative of normal dry batch ball milling of a material like dolomite. As an illustration of typical

Jan 1, 1968

By Ralph H. Sweetser

AT the end of 1943 the charcoal pig iron capacity of the United States was at the lowest point in over 1110 years, with only one strictly charcoal blast furnace in operation, and all others permanently out of blast except one in Tennessee d reported to he running on part charcoal and part coke. Such a decrease in production has taken place in spite of the O.P A.'s high-premium price on charcoal pig iron of +34 per ton f.o.b. furnace in Michigan. Depletion of the hardwood supply within fifty mlles or inure of the blast furnace is the reason why; the deplorable lack of reforesting is the cause.

Jan 1, 1944

By Peter Allen, John R. Stuermer

COUNTRY RISK ANALYSIS A company operating in a foreign country assumes all the risks that it would at home. However, beyond these, it assumes risks that arise from the unique political economic, financial conditions of the foreign country which it operates. These risks are known as "country risks". The importance of these risks has grown appreciably in the recent past (particularly in the aftermath of Iran's revolution in the late 1970s and Mexico's debt rescheduling of 1982-83), and as a result, country risk analysis has become an increasingly useful management tool. Country risk analysis seeks to assess the probability that countries will service their aggregate foreign liabilities on time, as well as the probability that country conditions could inhibit the debt service capability of private sector debtors. This involves assessment of both the ability and the willingness of countries to meet their external liabilities in a timely fashion. "Ability" is linked economic and financial variables: principally, a country's economic structure, foreign exchange generating capacity and debt service burden. On the other hand, "willingness" is tied to political factors: mainly the economic/financial orientation of government policy and the stability of economic decision making. Ability: Economic, Financial Conditions and Prospects Judgement of a country's ability to meet foreign financial obligations begins with a detailed study of a country's external balance sheet which compares the country's foreign liabilities and assets. Table 1 below presents country balance sheets for Mexico, Korea and Indonesia. [TABLE 1 The External Balance 3-,-et 1983 (billions of dollars; Indonesia Mexico Korea Foreign Liabilities 31.1 67.6 40.5 By Source: Bank 13.1 75.5 26.3 Non-bank 18.0 12.114.2 Foreign Reserves 9.3 4.7 7.0] The large magnitude of Mexico's external debt (nearly $90 billion), compared to foreign assets of approximately $5 billion, illustrates the weakness of this country's external payments position, and the main reason that it has been unable to meet interest and principal payments and been forced to reschedule its foreign debt. On the other hand, the relationship between Korea's external liabilities and assets ($50.5 billion and $7 billion, respectively), is more favorable and helps explain why Korea has been able to meet debt service payments and maintain its access to the international capital markets. Indonesia has even a more favorable relationship between its foreign assets and liabilities, $31 billion and $9 billion, respectively, and its debt is mostly lower interest rate, non-bank debt, making for a less onerous debt service burden. After the balance sheet, the analysis turns to a comparison of the country's foreign exchange earning capacity and its prospective financing requirements, that is, the country's future earnings stream

Jan 1, 1985

By A. W. Bitner, A. W. Asman

An analysis is made of three different types of section production units that represent the manner in which most of the nation's bituminous coal is produced. The general delays and production characteristics of these sections are presented along with a method for evaluating section performance based on actual and theoretical production characteristics. THE forerunner of the modern mechanical loading machine first entered the mines in 1890—a Stanley header with a conveyor. Since then progress has been substantial, both in the design and application of mechanized production units. Mechanization is almost a necessity for survival in the economy of today. In this paper an analysis is made of three types of sections, and a method for evaluating section performance based on present production characteristics and theoretical characteristics is presented. In mechanical loading mining sections the loading machine is the unit directly responsible for production. If the face preparation units provide a plentiful supply of properly prepared coal and the transportation system is coordinated and adequate, the loader will be idle a minimum of time. If either of the above do not perform adequately or other delays occur, the effect on production will be reflected in the performance of the loading machine. Therefore, attention is focused on the loading machine and factors that affect the overall performance of the production unit. Three complete mechanized production units are presented for analysis: A track section, a trackless section using battery-powered shuttle cars, and a trackless section using cable-reel shuttle cars. These particular sections were chosen for the following reasons: 1—The daily tonnage and mining conditions are approximately the same. 2— Production in each is 10 to 20 pct above the daily average. 3—The production characteristics and delays are average and typical. 4—They represent the manner in which the most of the nation's bituminous coal is produced. A. W. ASMAN, and A. W. BITNER, Members AIME, are Chief, and Research Assistant, respectively, Div. of Mining, The Pennsylvania State College, State College, Pa. Discussion on this paper, TP 3140F, may be sent to AIME by Oct. 31, 1951. Manuscript, Feb. 22, 1951. St. Louis Meeting, February 1951. Section A Fig. 1 is a layout for the track mining section showing the development to date, the projected plan and the cuts loaded on the shift studied. The seam mined averages 96 in. in thickness with a fireclay bottom and a roof of 10 in. of drawslate topped by sandstone. The mineability is considered good, and roof support is not a difficult problem. Two locomotives are used in the section to minimize the losses occurred in trip changing. The places are driven 20 ft wide, and the crosscuts are angled to permit fast tramming of the equipment. Table I lists the equipment and labor that make up the section. ANALYSIS Production Characteristics: The average loading rate for eight loading machines studied of this type is 1.81 tons per min. This one at 2.78 is considerably above average.

Jan 1, 1952

The Industrial Minerals div. has been forging ahead in formulating a program for the February Annual Meeting in Los Angeles. Several papers have been listed and more are being worked into the program. For the cement, lime and gypsum part of the sessions, papers on Gypsum in the Aircraft Industry, Geology of San Marcos Island Gypsum Deposit, and Status of New Dry Rotary Blast Hole Drills, are expected. The Chemical Raw Materials sessions will feature a symposium on potash, with 13 papers as the anticipated number to be presented. Airborne and Ground Magnetometer Work has been suggested. Eight papers have been set for Mining Geology, Four papers, Mining Phosphate Rock, Idaho Phosphorous, and Geology of Carlsbad Potash and Geology of Pearlite will be on the program. Sessions on Dimension stone and slate have been tentatively worked out with papers on Geologic Factors Affecting the Dimension Stone Industry of California, A Quarter Century of Granite Quarrying in Massachusetts, Rock Bursting and Other Geologic Problems in the Granite Quarries of Barre, Vt., Quarry Practices in the Indiana Building Stone Industry, Stratigraphy and Composition of the Salem Limestone, and Dimension Stone in the U. S. in 1952. The Rare Minerals Committee is aiming for six papers with two papers now definitely on the program.

Jan 1, 1952

By B. M. Harra, R. L. Hallows, O&apos

The term "modern automatic baghouses" as used in the title of this paper is intended to designate a general type of mechanical fume filter, introduced some 20 years ago and gradually improved since that time. It is characterized by its small filtering bags, enclosed in groups of 15 to 30 in steel compartments, and by its frequency of shaking, as compared to the old type of baghouse, which uses much larger bags, shaken at much longer intervals. Automatic baghouses are produced by a number of well-known manufacturers. Some recently constructed baghouses of the old type have embodied some of the principles of the automatic type, in that they are divided into several compartments, with separate fans for the different compartments, and flue headers arranged so that when the fan to any one compartment is shut down preparatory to shaking the bags in that compartment, the bags are put under suction by the draft from the other fans, thus making possible more efficient cleaning of the bags. These baghouses have motor-driven shaking mechanisms, and generally are operated under higher pressure and shaken at more frequent intervals than was the practice with the old style baghouse, and consequently have greater filtering capacity per unit of bag area. It is possible to interconnect the fan motors and the motors driving the bag-shaking mechanism, with suitable relays and timing devices, so that the operation of this type of baghouse also becomes to a considerable extent automatic. These baghouses are intermediate between the old style of baghouses, strictly speaking, and the completely automatic baghouses. They may he considered just as modern as the latter, and their proponents can no doubt cite many advantages for them. The authors are less familiar with them than with other types, and the following discussion will be limited to a comparison of the automatic baghouses and old style baghouses, with particular reference to the experience of The Eagle-Picher Lead Co. and The Eagle-Picher Mining and Smelting Company.

Jan 1, 1937

By Paul Giesecke

SINCE most modem metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. PRINCIPLES OF SPECTROCHEMICAL ANALYSIS In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1944

By Paul Giesecke

Since most modern metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with- the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. Principles of Spectrochemical Analysis In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, * visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1947

By Paul Giesecke

Since most modern metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with- the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. Principles of Spectrochemical Analysis In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, * visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1947

By AIME AIME

WITHOUT frills, but with an admirable program of technical papers and discussion, many opportunities for social contact, and all New York for a playground, the 142d Meeting of the Institute will make the Engineering Societies Building a lively place from Feb. 20 to 23. Prices are down, even in New York. Come and forget the depression listening to the stories of old friends. Hear at first hand what is going on in your professional world. The fare is varied, of wide appeal. The program on the opposite page has been arranged carefully to minimize conflicts between the subjects in which you are interested. If it is not possible to come for all four days, check over the sessions that are most important to you. No changes in the scheduling are likely.

Jan 1, 1933

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

PRIMARY products of the Josephtown smelter are zinc metal of various grades, lead-free zinc oxide pigments, cadmium metal, and sulphuric acid. Zinc concentrates of domestic and foreign origin are blended and desulphurized at the roaster plant. The equipment includes five, 12-hearth Herreshoff roasters and two modified Trail-type suspension roasters. The sulphur dioxide containing gases from the roasting operation are diverted to a four-unit contact acid plant for the manufacture of sulphuric acid. The roasted calcines are agglomerated by sintering on Dwight-Lloyd-type sintering machines; the sinter is crushed and sized within required limits; and the sized sinter is smelted in vertical shaft-type electro-thermic furnaces. Of the 13 electrothermic furnaces of various sizes now in operation, four are designed to produce American process zinc oxidc of various specifications; and the remaining nine furnaces are equipped with vacuum-type condensers and produce zinc metal. Papers describing the general smelting practice at Josephtown have been published by AIME. Since both High Grade zinc metal and lead-free zinc oxide pigments are produced direct from the electrothermic furnaces without need for subsequent refining, the elimination of impurities such as lead and cadmium has to be accomplished during roasting and sintering operations. To effect the producing of both High Grade and Prime Western zinc products, the roasting and sintering operations are on two separate circuits. A High Grade circuit produces finished sized sinter low in lead, cadmium, etc., for the High Grade furnaces; and the Prime Western circuit produces finished sinter destined for the furnaces producing Prime Western metal. Sintering at the Josephtown smelter differs in many important respects from the sintering practice in smelters operating horizontal retort zinc furnaces. Requirements of the electrothermic smelting furnaces define the physical characteristics of the sinter, while the chemical composition of the sinter is controlled according to the grade of metal and oxide to be made as final products. Three principal objectives in the sintering process at Josephtown smelter are: 1. To transform the zinc calcine from the roasting operations into a hard, yet porous agglomerate that will not crumble in the smelting furnace. 2. Crushing and sizing of the sinter to obtain a proper screen analysis which is normally —% in. down to +1/4 in. particle size. 3. To eliminate, particularly in the High Grade circuit, as much of the impurities such as sulphur, lead, and cadmium as possible. The sintering plant as originally built in 1930 was equipped with three standard 42 in. x 44 ft Dwight-Lloyd sintering machines. Each machine was equipped with a 15x60 in. sintering corporation fan driven by 150 hp, 900 rpm synchronous motor through a magnetic clutch and capable of delivering 30,000 cfm of air at 15 in. of water and 150°F. Each sintering machine was driven by 7½ hp dc motor with controllers for varying the speed of the machine from 8 to 32 in. per min. The pallets were cast iron and the grates of the herringbone type. The charge was mixed in a 4 ft diam x 8 ft Stehli pugmill and transported by belt conveyor, elevator and tripper conveyor to a small bin over each machine. Shortly after the start of operations the following changes were found necessary: 1. The herringbone grates which plugged very quickly and were difficult to keep clean were replaced by straight, narrow cast-iron grate bars running at right angles to the travel of the pallets. These grate bars are held in place by a center bar extending across the pallet on the 24 in. dimension and by removable retaining plates which form the sides of the pallets. 2. Mechanical grate knockers were developed in conjunction with new grate bars for continuously and automatically cleaning the grates. 3. As the cast-iron pallets cracked, they were replaced with cast-steel pallets. In 1938, the capacity of the sinter plant was increased with the installation of two 42 in. x 22 ft machines which were brought from the company's Herculaneum lead smelter. With a circulating load of some 250 to 300 pct, production of finished sinter on the 42 in. x 44 ft machines at this time amounted to about three tons of sized sinter per machine hour. In 1945, one of the 42 in. x 22 ft machines was replaced by a 60 in. x 44 ft machine of our own design. In 1948, as part of the plant-wide expansion program, the sinter plant not only was expanded but also divided into two separate plants; namely, Prime Western and High Grade circuits. The sinter destined for furnaces producing Prime Western zinc metal is made in a new plant comprising two 60 in. x 44 ft Dwight-Lloyd-type sintering machines, each having a 45,000 cfm Sturtevant fan at 18 in. water static pressure and served by an 8 ft diam x 12 ft long rotary charge pclletizer and auxiliary crushing and sizing equipment. The sinter destined for furnaces producing High Grade zinc metal and zinc oxide pigments is produced in the old sinter plant which was expanded to accommodate four of the 60 in. x 44 ft sintering machines, replacing the old sintering units. In the High Grade sinter circuit, two units of the 60 in. x 44 ft machines are used as preliminary soft sinter machines; and the remaining two units of the 60 in. x 44 ft machines are used to make finished hard sinter. Purification Theory Partial elimination of lead and cadmium in the sintering of zinc ores is common knowledge. However, by some manipulation and by taking advantage of the double circuit, it is possible to make zinc sinter which is nearly free of contaminators. Lead

Jan 1, 1952

By David Scott

THE MOGOLLON mining district, New Mexico, has received little public attention, although for 15 years it has been the leading silver producer of the state; it is situated in a region remote from the principal lines of travel, and its activities have usually been limited to the operations of two or three companies. The value of the total production of the district in the 44 years of its history has been estimated at $15,000,000. For the years 1904 to 1917, inclusive, the output was: gold, $4,370,000; silver, 10,042,000 oz.; copper, 874,862 lb.; total value, approximately. $10,500,000. In 1913 the district contributed 80 per cent. of the total silver production of New Mexico, but in 1917 only 41 per cent., due to serious interruption in the operations of the leading producer. Since 1914 the silver output has diminished one-half, and the present high value of silver is nearly offset by the increase in cost of production. The output of gold has rarely exceeded 35 per cent, of the total for New Mexico. The ratio of silver to gold, by weight, has averaged 46:1 based on the whole output of the district. LOCATION AND TOPOGRAPHY The town of Mogollon is 75 mi. (121 km.) by a poorly located highway from the nearest railroad terminals, at Silver City and Tyrone. All supplies are transported by motor trucks and teams. The area, sometimes called the Cooney Mining District, lies on the western flank of the Mogollon Mountains, which occupy the western part of Socorro County. The elevations drop steeply on the west to the valley of the San Francisco River, adjacent to the Arizona boundary. The topography is very rugged, the whole area being sharply dissected; deep canyons with steep gradients and rugged walls are characteristic of the whole western-slope of the Mogollon Range. The main canyons run east and west, and usually maintain a flow of water during the entire year. As would be expected in a region of such deep dissection, the

Jan 2, 1920

By Noel F. Boyd

Coal can be liquefied and gasified by several methods, all of which are being investigated and evaluated because each has its own advantages and disadvantages in terms of capital costs, end-products, and extent of required gas clean-up. Since coal conversion requires coal preheating to some extent, all these schemes begin with a coal-preparation step in a pressurized and heated reactor vessel where, in most cases, some additive or catalyst is usually injected. Extracting hydrogenated fuels from coal is not really a new science. Many people still recall the old "coal oil" that fired the lamps of stoves of rural America until the 1920's; the coal oil was produced by a basic Fischer- Tropsch method which has since been further developed to synthesize liquid fuels in the form of 86 to 90-octane gasoline and diesel fuel.

Jan 9, 1974

By J. S. Aronofsky, A. S. Lee

Results and experimental procedures are presented covering a preliminary laboratory investigation of the compaction of reservoir rocks and its effect on porosity and permeability. "Egective" compressibility was measured by subjecting core material to an overburden load and reducing pore pressure. Preliminary results showed relatively high effective compressibilities which varied from 1.8 X 10-' pore volume/pore volume /lb / in.~ for limestones to 7.7 X 10-6 pore volume/pore volume/lb/in.' and even higher for sandstone reservoirs conmining large amounts of fine clay material. It appeared from the initiol results that the effective compressibility of the material could not be correlated directly with porosity and that other factors, such as the amount of clay material present might have to be taken into account. The work to date has indicated that effective compressibility factors will have to be measured for the particular reservoirs heing studied. Oil permeability of core materid was measured under various effective overburden loads from 0 to 8,000 psi. It has been found than reduction of permeability in clean sands was relatively small and the results agreed with published data. For sandstones containing large amounts of clay, preliminary tests indicated very large reductions in permeability with increasing effective overburden pressures. It is planned to continue laboratory work on this phase because of its importance in low-permeability reservoirs. INTRODUCTION During the past few years increasing interest has been shown in the differences obtained between conventional laboratory measurements on cores at atmospheric pressure and those when reservoir conditions are simulated. Since these data are used as the basis for calculations and the prediction of reservoir behavior, their evaluation under reservoir conditions is most important. The effect of the compressibility of the rock upon the reservoir behavior, as fluid pressure declines, is an important subject which has been insufficiently studied. The total pressure on any plane through a reservoir is the result of the grain-to-grain rock pressure due to the overburden and the pressure of the interstitial fluid on the plane. As reservoir fluid pressure declines, the net load on the rock phase must increase, and the result is the compaction of the rock structure which produces a decrease in pore volume. Simultaneously, the rock grains expand into the pore space as the fluid pressure declines. The result of these two effects is defined as the effective compressibility of the rock and is expressed in units of pore volume/original pore volume/psi. Work was started by Imperial in 1954 on the effects of pressure on the porosity of reservoir rock. These studies established effective compressibility factors for some limestones and dolomites. Since that time effective compressibilities have been obtained for other Canadian and some U. S. reservoir rocks. In conjunction with the study of porosity, an investigation has also been initiated to determine the effects of pressure on permeability. One outcrop and several reservoir sandstone cores have been tested to date. ROCK COMPRESSIBILITY Apparatus anD Procedure A diagram of the apparatus used in these studies is shown in Fig. 1. The equipment was constructed so that a uniform pressure, equivalent to the reservoir overburden, could be applied by the oil pump and transmitted on all sides of the core through the Lucite sheath. The sample was completely saturated by circulating brine through the mounted core. Pressure in

By David W. Brunton

From the old-fashioned " grab-sample " to the modern timing-device, which takes a machine-sample with mathematical precision, there is a wide gap, which was only crossed by many years of toil and unremitting endeavor. Even to-day, notwithstanding the advancement in the art, " grab-sampling " is still practiced—sometimes to afford the unscrupulous mine-promoter a basis for fairy-tales with which to entrap the too-gullible investor, and often by milling and smelting companies to determine the amount of moisture in custom-ores. The latter practice is almost as reprehensible as the former, and it causes more trouble and ill-feeling between seller and buyer than all other factors put together. -NO reputable concern to-day would think of attempting to determine by grab-sampling the amount of gold, silver, lead, or copper contained in an ore, and yet many buyers expect the miner to accept the results of grab-sampling in the determination of the amount of water contained in the ore, forgetting that accurate results are just as necessary here as in the determination of the metals, because the result determines the percentage of weight of the ore which shall be excluded and considered to have no value whatever. Samples for the determination of moisture should be taken with as great care as samples for the determination of metallic content, and in order to avoid the extra expense of a separate operation moisture-samples should be taken from the sample-safe. As the sample reaches the sample-bin in a smaller stream and by a more circuitous route than the " reject" travels in its path to the outgoing car, it loses more moisture en route, and a constant should be added to compensate for this difference. Carefullg ,con ducted experiments have shown that the differ.elice in loss of moisture between the two routes does not exceed 10 per cent. in summer and 7 per cent. in winter. For instance,

Jan 1, 1910

By G. H. Clevenger

Continuing the discussion of the paper of James Johnston, presented at the New York meeting, February, 1914. See Trans., xlviii, 3 to 32 (1914). This paper cannot fail of being of great interest and value to all who are interested in the cyanide process, on account of the important developzn~ents which it records. Mr. Johnston is to be commended for the large amount of detail which he gives, and the company and its management for permitting the publication of data of this character, which while of great value to others could well be considered private property. It might be discussed from a number of standpoints: First, as an example of recent practice in mill and cyanide plant construction; second, the mill practice; third, the cyanide practice; and fourth, the new features in cyanide treatment involved. Perhaps a more vivid way of expressing it would be: First, the equipment or tools with which the various operations are carried on, are they the best and most efficient which could have been selected for their respective uses; and, second, is the best use in every case made of these tools? It may be well inquired is the highest possible recovery of silver made at the lowest cost per ounce recovered? For after all, the making of the greatest ultimate profit is inseparably associated with successful metallurgical practice; there must therefore be at all limes a careful balance maintained between recovery and cost of obtaining it. I wish to call attention in a very general way to the equipment used and to an anticipation of questions which are bound to arise in this connection. However, the bulk of my discussion will be confined to the presentation Of certain additional data, together with a more or less general discussion showing the line of development which leads up to the present practice and the applicability of certain features of it to similar problems elsewhere. There are a number of vital points of broad general interest involved in Nipissing low-grade practice upon which metallurgists will by no means be agreed to which I wish to call particular attention in the hope that it will lead to the presentation by others of data of practice in other districts which will assist in reconciling this divergence of opinion.

Jan 1, 1915

By J. S. Crump, C. R. Hocott, A. E. Hoffman

Planning of the efficient operation of a gas-condensate reservoir requires a knowledge not only of the gross phase behavior of the system but also of the equilibrium distribution of the various components between the gas and condensate phases. This equilibrium distribution can be calculated with appropriate equilibrium constants. In this paper are presented equilibrium constants determined experimentally for the oil and gas phases initially present in the same reservoir and for the gas and condensate phases of the gas cap material at a series of pressures below the original reservoir pressure. Also presented is a method for the correlation of the experimentally determined equilibrium constants. The utility of the correlation is demonstrated further by an example of its use in adjusting the equilibrium data to permit their application to another gas-condensate system of similar composition. INTRODUCTION Planning of the efficient operation of a gas-condensate reservoir requires a thorouugh knowledge not only of the gross phase behavior of the particular hydrocarbon system but also of the equilibrium distribution of the various components between the gas and condensate phases. At the initial conditions of reservoir temperature and pressure, the original hydrocarbon materials in a gas-condensate reservoir or in the gas-cap of an associated reservoir exist in a single, homogeneous vapor phase. However, some condensation of hydrocarbons to a liquid phase usually occurs in the reservoir as pressure declines incident to production. Because of this condensation. the produced gas changes composition continuously. The composition of the produced gas, as well as that of the condensed liquid, can be calculated from the composition of the original reservoir material through the application of appropriate equilibrium constants or "K"-values provided these values are known. Equilibrium constants have been used for many years in problems of surface separation of gas and oil and natural gasoline recovery. However, no satisfactory equilibrium data at reservoir conditions have been available for the higher boiling hydrocarbons which acquire abnormal volatility at high pressure and are therefore present in the gas phase in condensate reservoirs. Early work in this field indicated that the behavior of the higher boiling hydrocarbons largely determines the behavior of gas-condensate systems at high pressure.' Consequently, a portable test unit was designed to permit determination of the distribution of the heavier hydrocarbons between the gas and liquid phases of a gas-condensate system. This paper describes the test equipment and presents the results of an investigation of the reservoir fluids from an associated oil and gas reservoir in the Frio formation in Southwest Texas. Also presented is a method for correlation of the experimentally determined equilibrium constants, together with an example of the use of the method in adjusting these data for application to another gas-condensate system of similar composition. FIELD TESTING AND SAMPLING In order to determine the compositions of the reservoir fluids, field samples were secured from two different wells, one completed in the oil zone, and one completed in the gas cap. The oil well was completed through perforations in 51/2-in. casing at a depth of 6,822-6,828 ft subsea. Pressure and temperature traverses made in the well indicated the pressure and temperature to be 3,831 psig and 201 °F, respectively, at a depth of 6.828 ft subsea. Subsurface samples were taken from this well after a four-hour shut-in period.

Jan 1, 1953

By A. A. Smith, J. S. Smart, A. J. Phillips

The preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in propertties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. Preparation oF High-purity Copper The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuSO4-H2SO4 electrolyte using bagged anodes, low current density (5 amp. per sq. ft.) and low tem- perature (25°C max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe2(SO4)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then reatered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2SO4 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 4 3/4 by 4 3/8 by 1-in anodes cast from high-quality electrolytic wirebar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars—which would result in fouling of the contacts—-and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By A. J. Phillips, A. A. Smith, J. S. Smart

The preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in propertties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. Preparation oF High-purity Copper The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuSO4-H2SO4 electrolyte using bagged anodes, low current density (5 amp. per sq. ft.) and low tem- perature (25°C max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe2(SO4)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then reatered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2SO4 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 4 3/4 by 4 3/8 by 1-in anodes cast from high-quality electrolytic wirebar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars—which would result in fouling of the contacts—-and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941

By M. W. BERNEWITZ

IT is 27 years since I last visited Broken Hill, New South Wales, one of the world's greatest lead-silver-zinc districts. Then, the flota¬tion of ores was in its infancy. The Minerals Separation process had its birth as a practicability in the Central Mill, which is still operating and yielding high recoveries. The average Australian knows that Broken Hill is an important mining center in a "corner" of New South Wales, but he does not know what a factor it is in the lead, silver, and zinc production of the world. Nor does he realize that among the ramifications arising from metal production at Broken Hill are the great lead smelter at Port Pirie, South Australia, 254 miles southeast; the electrolytic zinc works at Risdon, and the limestone mine at Davenport, Tasmania; the acid works at Cockle Creek, New

Jan 1, 1935