Search Documents

(Under this heading will he published notes sent to the Secretary of the Institute by members or other persons introduced by members.) No. 488.-Mining engineer, member, technical graduate, married, age 38, desires position of superintendent or assistant superintendent. Has had 15 years' practical experience as miner, millman, machinist, surveyor, engineer, foreman, and superintendent in the West, Southwest, and Mexico. Speaks Spanish. Now employed as superintendent of copper property in Southwest. Can give the best of references. Minimum salary $250. Available now. No. 491.-Mining engineer, member, married, age 43, desires to connect with some-good coal company as superintendent or manager. Is thoroughly conversant with flat and pitching systems of coal mining. Has had 23 years experience from the bottom up; 7 years experience as superintendent and manager. Good organizer. Has handled all classes of labor acid has always made good. Available now. No. 492.-Metallurgist and chemical engineer, member, with 8 years executive experience in research and technical direction of all departments of nom-ferrous metallurgical manufacturing, is open for change in position. Specialist in raw materials-and supplies, reclamation of wastes, and standardized control of processes. No. 493.-Member, age 37, technical education, married. Seventeen years' experience as superintendent, engineer, chemist, and assayer, exploration engineer in United States, Central and South America, Siberia and India. Especially in iron, manganese, copper, and rare metals. Desires to make a change. No. 494. Electrometallurgical engineer, member, age 30, A. M. and Ch. E. degrees, thoroughly trained in electrochemistry, metallurgy and electrometallurgy. Three years in charge of experimental work on and operations of electric furnaces. Desires responsible position in investigative or executive work with commensurate salary.

Jan 11, 1918

By Joseph A. Norden, A. R. Willson

Much has been written concerning the hoisting equipment of various mines throughout the country, but most of the literature on the subject, if not all, describes equipment of extraordinary capacity and the small and medium-sized outfits have been neglected. The hoisting equipment here described is capable of handling about 1200 tons per day. It has not been worked to capacity, but 600 to 700 tons, together with men and materials, have been handled in two shifts without any great effort. Only one shaft extends from the surface to the lowest levels of the mine; see Fig. I. It is composed of three compartments, two of which are used for hoisting, and the third for water, air, and electrical lines, and for sinking purposes. In 1909, this shaft was raised from the 1000-ft. (304-m.) level to the 700-ft. There a station was cut and an air hoist installed. At this time all mining operations were confined to the upper levels of the mine; that is, above the 700-ft. The ore was dropped to this level through chutes from the 300-, 400-, 500-, and 600-ft. levels and then lowered in cars on cages to the 1000-ft., which is the main haulage adit, the mill and railroad bins being about 3000 ft. from the shaft. Orebodies were, in due time, developed on the 1000-ft. level and below. Therefore, in 1913,the shaft was sunk to the 1150-ft. level and thereafter sinking was continued at regular intervals until the 1500-ft. level was reached. But, hoisting from the 1300-ft. level was a difficult and slow process with the antiquated air hoist, so, in 1916, it was decided to raise the shaft to the surface and install a modern, electrically operated hoist. This was completed early in 1917 and the hoist was in operation in March of that year. The Hoist Figs. 2, 3, and 4 show various features of the hoist and electrical equipment. A Nordberg engine of the double-drum, geared type, designed for a 10-ton load, including rope, at a speed of 1500 ft. per min., is used. The drums are 7 ft. (2.1 m.) in diameter, with a 54-in. (137-em.)

Jan 1, 1922

E. W. Parker, Washington, D. C.: In connection with Mr. Blauvelt's paper, a brief sketch of the development of by-product coke-making in the United States may prove of interest. The first radical departure from the prevalent beehive oven to the by-product retort oven was inaugurated in 1891 by the Solvay Process Company, at Syracuse, N. Y. In that year was begun the construction of 12 Semet-Solvay ovens, which were completed in 1893. During 1893 these ovens produced 12,850 tons of coke, an average.of a little over 1000 tons each. In the following year the production amounted to 16,500 tons, not quite 1400 tons per oven. These 12 ovens were in reality an experiment, the success of which was attested by the addition to the same plant of 13 more ovens, begun in 1895 and completed in 1896. They were followed by the construction in 1896 of 25 ovens of the same type at Sharon, Pa., and 50 more at Dunbar, Pa. These 100 ovens represented the total number of Semet-Solvay ovens completed and in operation up to the close of 1897. The construction of 180 more, however—120 at Ensley, Ala., and 60 at Benwood, near Wheeling, W. Va.—was begun in 1897. The plant for the latter is laid out for double the number stated. The 60 ovens begun in 1897 have now been completed. An initial plant of Otto-Hoffman ovens was built at Johnstown, Pa., in 1895, and began making coke in 1896. One hundred and twenty additional ovens of this type were begun in 1896 and completed in 1897 at Glassport, near McKeesport, Pa. During the present year 100 Otto-Hoffman ovens are being added to the plant at Johnstown, and 400 of the same type are in course of construction at Everett, near Boston, Mass. The plant at the latter place is laid out for a total of 1200 ovens.

Jan 1, 1899

By Harmel A. Dawson, Robert A. Wilson

First the basic steps to determine the values present and the minerals involved which are the basis for the metallurgical testing are presented in this paper. Next, choosing the process or processes indicated for treating an ore are discussed. This is followed by the test procedures used, the results of which will indicate amenability to treatment. These test procedures have been developed, used and proven effective in laboratory evaluations relative to plant processing. Special, uncommon processing is beyond the scope of the paper. Evalutation of test results and incorporation into the preliminary and final flow sheet for plant design are discussed. The value of a flow sheet, with material and water balances, to plant design is shown.

Jan 1, 1978

By J. J. De Witte, J. G. Cazort

The Paranam plant in Surinam (formerly Dutch Guiana) was built during 1939-40 to supply crushed and dried bauxite for the growing U.S. aluminum industry, supplementing production from the Suriname Aluminum Co.'s Moengo works, which began operation in 1922. A subsidiary of Aluminum Company of America, Suralco's total annual production from these two plants averages 2.55 million dry metric tons of various grades of bauxite. Starting in 1941 with bauxite from mines on the west side of the Suriname River, annual production at the Paranam plant has varied from a low of approximately 450,000 tons to more than 1 million tons in 1949. High production rates during World War II and the late 1940's rapidly depleted these reserves, and in 1950 plans were made to mine the known deposits on the east bank of the river, about five miles downstream from the original Paranam plant.

Jan 11, 1960

By E. A. Gulbransen, A. Pebler

Pressure-composition isotherms have been determinedfor the systems ZrMo2 -H2 between 0" and 900°C at hydrogen pressures between 10-4 and 760 Torr. Tkese studies plus X-ray diffraction analyses of selected compositions show that these intermetallic compounds form a complete series of hydrogen solid solutions within this temperature and pressure range. The partial molar enthalpies and entropies of solution of hydrogen in the three intermetallic compounds were calculated. The solubility of hydrogen in these Laves phases can be related to their free electron concentration. ThE reaction of hydrogen with inter metallic compounds of zirconium with Laves phase-type structure has both theoretical and practical interest. The in-termetallic compounds have structures different from any of the pure metals. In addition the electron to atom ratio of the intermetallics varies appreciably. In the nuclear materials field, these materials are of interest since intermetallic compounds may exist as precipitates in commercial zirconium alloys with transition metals. From studies on the hydrogen reaction, one can establish the stability of the intermetallic compounds relative to the hydrides of the component metals. The intermetallic compounds may also be used as getters for hydrogen and as materials for hydrogen storage. This paper will present the results of equilibrium and structural investigations of the ZrCr2-H2, the ZrV2-H2, and the ZrMo2-H2 systems for the temperature range of 0" to 900°C and the pressure range of Torr to 1 atm. A complete thermochemical analysis will be made of the measurements. Some of the results have been referred to in a survey paper' covering the types of hydrogen behavior observed in zirconium alloys. LITERATURE ZrCr2 is the only intermetallic phase in the Zr-Cr system.' It exists in two allotropic modifications. Between 900" and 1000°C the hexagonal MgZa (C14) structure transforms into the cubic MgCu2 (C15) structure. Beck4 has previously shown that the intermetallic ZrCrz takes up hydrogen into solid solution up to a composition H/ZrCr2 = 1.14 at room temperature and 1 atm hydrogen. A ZrCr2 hydride was stated to have a fcc structure. The binary Zr-V system has been investigated by williams5 although Rostoker and Yamamoto 6 had given earlier a partial phase diagram. ZrV2 was the only intermediate phase found in the system. wallbaum7 reported earlier that the compound ZrV2 hp the MgZm (CJ4) type structure with a = 5.288A and c = 8.664A. This was not comfirmed by Elliot8 nor by Matthias, Compton, and corenzwit9 who reported that ZrV2 has a cubic MgCua LC15) type structure. The latter authors gave a = 7.429A. Also, several authors do not agree on the temperature of the peri-tectic horizontal. It appears that ZrV2 may exist in several modifications. A high capacity for occluding hydrogen was reported by Beck4 who found H/ZrV2 = 1.38 at room temperature and 1 atm of hydrogen. ZrMoz is the only intermetallic phase in the Zr-Mo system.10 ZrMoa is formed by a peritectic reaction of the melt with a molybdenum-rich solid solution. ZrMo2 has the C15-type structure with a = 7.59A. MATERIALS High-purity chromium, vanadium, and molybdenum were used together with grade 1 crystal bar zirconium to prepare the alloys. Table I lists the chemical analysis and the sources for the metals. Ten-gram alloy compacts were levitated and melted in an inert argon

Jan 1, 1968

By H. H. Campbell

In the extending employment of open-hearth steel for structural purposes, it is a matter of prime importance that the test-piece shall represent with practical accuracy the characteristics of every portion of the heat from which it comes. In ordinary practice this homogeneity is assumed; but inasmuch as leading exponents of the revolving-hearth system have claimed that a reasonable uniformity could be obtained by their method alone, it may be pertinent to offer a few facts on the subject. The following heats made by the Pennsylvania Steel Company, for bridge-work, were tested by casting two four-inch ingots, one being taken during the first third and the other during the last third of the cast. Test-pieces obtained from these small ingots usually give results inferior to those obtained from larger sizes; but for purposes of cornparison they are equally conclusive. Many of the tests were made for experimental purposes within a few hours of the time of rolling, and before sufficient time had elapsed for the usual molecular redistribution necessary for the best results. All the tests were made on 3/4-inch rounds just as they left the rolls and without annealing; the results, therefore, are subject to the errors caused by variations in the diameter, and in the temperature at which the bar was finished. The tests from any one heat, however, were always nude as nearly as possible under the same conditions; and inasmuch as these data include the results of every heat so tested, and inasmuch as the errors could not by any chance always support any single theory, we may be certain that the unanimons testimony of the experiments indicates a valid conclusion.

Jan 1, 1886

By W. A. Anderson

IN the pressure die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger and a complete shutdown of the equipment. All of the zinc alloys used for pressure die-casting today contain approximately 4 per cent of aluminum, which is more than sufficient to make plunger operation feasible. The clearance between the plunger and its bushing is an important matter. As the space becomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still used in some machines. However, the rate at which the plunger clearance increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new materials more capable of retaining the desired clearance during long periods of use. Today many die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the plunger will operate for a long time, of course. The authors have developed a laboratory apparatus in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clear-ance area.

Jan 1, 1939

By G. M. BUTLER

TWENTY-ONE of the states in the Union, the Territory of Hawaii, and seven provinces of Canada now have in operation laws requiring that professional engineers be registered or licensed. In addition, two states require that civil engineers be registered, and one other state demands registration of structural engineers. Moreover, nearly every year sees additions made to the list. The registration movement, fostered by the American Association of Engineers, now has the powerful, energetic backing of the An1,erican Society of Civil Engineers, which is itself now fostering registration legislation, and there is a strong sentiment in favor of registration in the American Institute of Electrical Engineers and the American Society of Mechanical Engineers. Only in the American Institute of Mining and Metallurgical Engineers is anti-registration sentiment, strongly dominant, but many members of this organization are enthusiastic advocates of registration.

Jan 1, 1930

By E. E. Anderson, R. L. Newacheck, J. Kohl

Radioactive materials were used underground before the advent of the nuclear reactor. Radium containing ores have been mixed with cements and other materials for later location in oil wells by gamma ray logging since 1940.1 Perforating bullets have been marked with radium salts,, and radioactive materials have been added to drilling muds to find the cause of "lost circulation."' More recently colloidal suspensions of radioactive cobalt-60 and silver-1103 and solutions of 1-1314 have been used in waterflooding operatiorns to determine injection profiles, flow paths and water velocities. In this paper a recent and interesting underground tracer application is discussed. Development work and field engineering were carried out under the direction of Tracerlab, lnc., with assistance from personnel of the client. A gaseous tracer, argon-41, was used in an attempt to determine the cause of leakage from an underground gas storage reservoir. STATEMENT OF PROBLEM This gaseous tracer application was carried out for the Natural Gas Storage Co. of Illinois. This company has developed an underground gas storage field 1,750 ft below the surface of the earth near the village of Herscher, Ill., about 60 miles south of Chicago. The total volume of gas stored in the field was estimated to be about 13 billion cu ft in the spring of 1954. The field has a maximum estimated storage capacity of 90 billion cu ft. The gas is contained in the Galesville sandstone, previously a water bearing formation of about 25 per cent porosity. The water as it is pushed out by the gas forms a barrier for the gas around the edge of the reservoir. Over the top and beneath the bottom of the reservoir are located several layers of impervious rock, which barring cracks or unplugged and unknown wells should act as seals. Twenty-one injection and withdrawal wells were drilled into the Herscher reservoir and gas injection was begun during the summer of 1953. After a few weeks of gas injection, evidence of gas leakage was detected at the surface; water wells began bubbling and losing prime, and dry spots in the fields indicated gas leakage from uncharted oil wells. In every case, the leakage could not be traced back any further than the water bearing formations a few hundred feet below the surface. An extensive search was made to locate uncharted oil wells which were believed to be possible channels for the gas from the storage formation to the water containing formation. Long-time residents in the area assisted in the location of several abandoned oil wells. The wells when located were cleaned out and either used as vent wells to relieve the gas pressure in the water formations, or were plugged with cement. None of the wells even approached depths which would endanger the soundness of the storage reservoir. All of the injection wells were tested for leaks in the casings by conducting neutron surveys and by other techniques. To detect any leakage up through the cement-filled annulus surrounding the casing, a section of the casing wall in one well was milled out. Then, plugs were installed above and below the cut-out section and pressure applied to the annulus, which proved conclusively that the cement was sound in that well. The well was then plugged with cement and abandoned. In another well, ammonia was injected into the well and a temperature log was made. It was hoped that a leak would be re-

Jan 1, 1956

By G. R. Leverant

RECENT investigations1,2 of the low-cycle fatigue behavior of pure copper under strain cycling conditions have shown that a unique saturation stress level is eventually attained for each value of applied plastic strain amplitude. The dislocation substructure of copper at the saturation stress level is in the form of cells whose diameter decreases with increasing saturation stress level, i.e., plastic strain amplitude. In addition, both the saturation stress level and the cellular substructure are completely reversible. That is, the saturation stress level and accompanying cell size are determined solely by the present conditions of testing and are, therefore, independent of any previous cyclic history. The mechanical and substructural reversibility observed in pure copper, which has a relatively high stacking fault energy, is not observedz for Cu-7.5A1 which has a much lower stacking fault energy. This implies that easy cross slip (wavy slip) is a prerequisite for reversible fatigue behavior. A dispersion of fine, nondeformable particles of a second phase in a metal matrix tends to stabilize substruc- tures introduced by forming operations during subsequent elevated-temperature heat treatments.3 This raises the question as to whether a finely dispersed second phase can induce an element of irre-versibility into the cyclic deformation behavior of a wavy slip material at room temperature, due to partial stabilization of the initially introduced substructure. Since nickel has a higher stacking fault energy than copper,6 pure nickel should be characterized by cyclic reversibility. Therefore, TD-nickel* (Ni-2ThO.r) was

Jan 1, 1968

By T. J. Woodside

Prior to 1927 the lead blast furnace charge at El Paso consisted principally of direct-smelting carbonate ores, very low in zinc, and the resulting slag seldom carried more than 4.0 pct. With the exhaustion of the mines in Northern Mexico which supplied these ores, they were supplanted with a much smaller tonnage of sulphide concentrates containing appreciable amounts of zinc, and the zinc content of the slag rose to 10.0 pct. The Anaconda Company's slag fuming plant at East Helena, Montana, had then been in successful operation for several years, and it was immediately recognized that, while at that time the production of high zinc slag was small, if the grade held, a plant for the recovery of zinc from the accumulated slag might some day be practical. The grade not only held but became increasingly higher so that by 1946 suffcient slag had been accumulated to warrant the construction of a fuming plant regardless of future slag production from the blast furnaces, and with the removal of Government restrictions on construction at the end of the war the project was undertaken. The general design of the plant follows that at Bunker Hill, with waste heat boiler, unit coal pulverizers and even more extensive instrumentation and automatic control. The area around the lead blast furnaces is rather congested, being cut off from the nearest feasible site for the fuming plant by the copper plant, so that the most practical route for hot slag transfer is through the converter aisle. For this reason and also to make use of the existing converter cranes to serve the fuming furnace, an unused reverberatory at the north end of the converter building was dismantled and the fuming furnace and boiler located in its place. A flue at right angles to the furnace and boiler runs northward to the U-tube coolers and baghouse (Fig 1). From the bag-house a steel flue runs eastward to an existing and long unused 300 ft con- Crete stack. The coal handling system and de-leading plant lie north of the furnace and east of the cooling tubes and baghouse. The furnace is conventional, 8 X 21 X 33 ft high inside and completely water jacketed (Fig 2). There are 21

Jan 1, 1950

By Howard L. Hartman

The past 15 years have seen rapid advances in the metallurgy of materials for drill machinery and bits, but rock drilling itself continues to be largely an art. Jet piercing, roller bit rotary drilling, and rotary percussion are all promising new techniques, but the percussion rock drill, still used for 90 pct of the blastholes in U. S. hard-rock mining, has under- gone no major modification since pneumatic machines were first used successfully in the 1860's. This singular lack of progress stems directly from ignorance of the nature of impact failure of rock and the fundamentals of rock penetration in general. For nearly three-quarters of a century, mining engineers did not know what went on at the bottom of a drillhole.

Jan 1, 1959

By Frank Nicholson

Copper ore was first noticed in Ste. Genevieve County in 1563. The diswvery mas made by a German farmer named Simon Grass, who had occasion to make a road from his farm down the hill into the neighboring valley, and while so engaged noticed pieces of a green-colored mineral, some of which he collected. Not knowing the character of the ore he had found, and supposing it to be valua ble for its brilliant green color only, he carried a piece with him into the town of Ste. Genevieve and showed it around the various bar rooms as a curiosity. No special attention was paid to the matter until nine years later, when Mr. 0. D. Harris sent a specimen of the ore to Dr. Theodore Fay, of St. Louis, for analysis. This analysis, which was the first ever made of Ste. Genevieve copper ore, showed the specimen to contain : Copper,. .........17.75 per cent. Zinc,..........3.21 " Iron........... 24.50 " Sulphur ..........1.09 " Organic matter, silica, carbon, and oxygen,. .. 53.45 " 100.00 " From this analysis it is evident that the sample was taken from near the surface, and was probably recognized by its green color. The almost entire absence of sulphur proves it to be an oxidized form. There is on file, at the office of the Ste. Genevieve Copper Works, a paper* giving three arsays of the ore made in 1875 by Henry B.

Jan 1, 1882

By T. P. Oxford, G. Y. Onoda, E. D. Whitney

Disposal of phosphatic clay waste slurry has been a problem since the advent of hydraulic processing of phosphate rock in Florida. Alternatives to the present practice of storing slimes behind earthen dikes have been earnestly sought for more than a quarter of a century. Seepage dewatering is a promising technique intended to increase waste clay solids content to a level sufficiently high to permit clay disposal in mine cuts, in lieu of above-grade impoundment. An experimental array of vertical seepage columns containing mine tailings sand was constructed. Significant improvement in waste clay dewatering relative to that occurring in a control test was observed when approximately 1800 m3 of waste clay was disposed of in the presence of the seepage aids.

Jan 1, 1983

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

Solid-solubility limits at 1500°, l000q and 500°C for carbon, nitrogen, and oxygen in high-purity tantalum were determined by X-ray lattice-parameter methods. For carbon, the solubility was found to be 0.17 at. pct at 1500°C, and less than 0.07 at. pct at 1000°C. A nitrogen solubility of 3.70 at. pct at 1500° C decreases linearly with temperature to 2.75 at. pct at 1000°C, and 1.8 at. pct at 500°C. In the case of oxygen, the solubility was found to be 3.65 at. pct at 1500°C, 2.95 at. pct at 1000°C, and 2.5 at. pct at 500°C. The phases Ta2C, the low-temperature modification of Ta205, and Ta,N of unknown composition but which has a superlattice structure based upon the original bcc tantalum lattice have been identified as the initial precipitates in the respective systems. Metallographic methods were employed to verify the X-ray analyses. The etching behavior of Ta is discussed in terms of lattice i?rzperfections and precipitate phases. The excellent fabricability, high melting point, and nuclear properties of tantalum are responsible for interest in this refractory metal. Data on the solid solubility of the interstitial elements (oxygen, nitrogen, and carbon) in tantalum and on the precipitate phases are somewhat limited. The significant contributions are discussed below. Because the purity of electron-beam melted tantalum (only recently available) is considerably higher than that used in previous studies, the present investigation was initiated. Gebhardt et all-3 have investigated the tantalum-oxygen and tantalum-nitrogen systems with particular reference to the changes in physical properties and to the rates of reaction between these gases and the metal. The solubility of oxygen in tantalum was reported2 to be 3.7 at. pet at 1500°, 2.3 at. pet at 100O°C, and 1.4 at. pct at 750°C. Schonberg4 reported that several oxide phases (Ta40, Ta,O, TaO and Ta,05) exist while X-ray studies by Gebhardtl showed only two oxides, Ta,05 and an unidentified phase which was associated with a platelet-type precipitate. La-gergren and Magneli,' however, questioned the existence of compounds other than the two allotropic modifications of Ta,05 for the tantalum-oxygen system. In the case of nitrogen, the solubility was estab- lished by Gebhardt3 to be of the order of 7 at. pct at 1800°c. The solubility was reported to decrease rapidly with temperature, and, although no limits were established, a precipitate phase was observed by Gebhardt except when the high-nitrogen specimens were cooled very rapidly from the reaction temperature of 1800c. He reported the initial precipitate phase to be a tetragonal distortion of the bcc tantalum lattice while Schonberg6 reported the phase lowest in nitrogen Jo be a cubic super-lattice with a cell size of 10.11 A. Two other nitride phases, Ta,N and TaN, were reported; these appear to be isomor-phous with the carbides of tantalum. The tantalum-carbon system was investigated by Ellinger7 and by Lesser and Braurer. Two compounds, Ta,C and TaC, were reported to exist, each with a range of composition. The solubility of carbon in tantalum was found to be practically nil at all temperatures. Thus, of the interstitial elements which are present in small amounts in high-purity tantalum, carbon might be expected to form precipitates. The present investigation was initiated to obtain additional data on the solid-solubility limits of these interstitials at 1500°, 1000°, and 500' with particular emphasis on the distribution and the identification of the precipitate phases. EXPERIMENTAL WORK AND RESULTS In the present investigations of the solid solubility and of the precipitate phases in the systems tantalum-nitrogen, -oxygen, and -carbon, high-purity tantalum was reacted with high-purity gases, homogenized at 1800°c, and annealed at and quenched from 1500°, 1000,

Jan 1, 1962

By C. R. McEwen

The displacement equations of Buckley and Lever-ett' have been successfully applied to the prediction of oil recovery in frontal drives for a number of years. Commonly, the capillary pressure term is omitted from Leverett's fractional flow formula. The resulting satura-tion-vs-distance curves become multi-valued, however. Buckley and Leverett, recognizing that the neglect of capillarity was most likely the cause, proposed that this part of the solution he ignored. An ingenious method of propagating a discontinuity in place of the multi-valued portlon of the curve was devised by Cardwell using "non-capillary displacement theory". However, it would seem that a completc description of the displacement pracess would require the inclusion of capillary forces. Three publications on displacement theory have appeared in which capillary pressure was included. Ter-williger. et al', calculated saturation profiles which matched those which they observed when gas displaced water vertically downward. Based on their study, Jones-Parra and Calhoun5 roposed a method of computing saturation distributions sufficiently removed in time from the initial conditions so that all saturations in the flood front region were assumed to move with the same velocity. This latter assumption corresponds to the tangent construction on the flowing fraction-vs-satura-tion curve proposed by Welge." A numerical solution to the problem of water displacing oil from a water-wet porous medium was recently presented by Blair, ef at'. The initial conditions included a uniform saturation slightly above interstitial water saturation. that is, the permeability to water ahead of the front was not zero. This appeared to result in a region of slowly rising water saturation ahead of the front, at least for the particular set of relative permeability and capillary pressure data used to illustrate the computation. The authors also postulated an "end-effect" at the outflow face of the system, whereby no water could pass out of the system until the water saturation had built up to a high value. The saturation profiles computed under these assumptions show water accumulating at the downstream end of the system while the flood front proper is still traveling toward the outlet. The purpose of this paper is to present the results of a numerical solution to the one-dimensional water-flooding equation in which no outlet end-effect is considered and where there is no flow of water ahead of the flood front. It should be noted that the contemporary paper of Fayers and Sheldon8 deals with the problem under discussion. For a thorough treatment including both capillarity and gravity the reader is referred to their paper.

By Earl G. Alexander, W. R. Runyan

The nature of silicon growths which form on amorphous silicon dioxide during epitaxial deposition in unmasked areas was investigated. Octahedral silicon crystals nucleate and grow on the oxide at pinholes, adjacent to foreign matter, and probably at oxygen-deficient sites. Generation of these oxygen-deficient sites on the oxide surface is shown to be thermody-namically favorable under usual deposition conditions. The conditions which affect saturation (SiCl4 concentration, flow rate, temperature) determine the number of sites on which silicon will nucleate and grow. Reaction product HCl is likely responsible for suppressing silicon growths on the oxide near exposed areas of silicon. Evidence is given that the oxide-silicon interaction occurs in hydrogen only and involves water as a transport agent. SINCE shortly after the first epitaxial layers of silicon and germanium were grown over large areas, efforts have been underway to grow selectively on specified portions of the surface. Such selective growth should be particularly applicable to monolithic integrated circuits. Usually the approach has been to use a mask to delineate the desired area,'-7 but the VLS methoda can also be used, and direct programmed atomic beam deposition has been suggested.9 The masking techniques may embody two forms: in one the mask is a material which can later be removed along with any growths attached to it; in the other, attempts are made to prevent growth on the mask, so that over a whole slice the only deposition that will occur is in the unmasked regions. The present work is concerned with only the latter case, and specifically with silicon. Joyce and Baldrey1 suggested the use of thermally grown silicon dioxide as a mask material and showed that for the proper choice of operating conditions (total flow, SiCl4 concentration, total deposition time, and temperature) spurious growth could be minimized and that if the deposition times were not too large, and the criteria not too stringent, a usable process occurred. Later Schnable et al 4 observed that after extended deposition times, during which most of the silicon dioxide became covered with growth, there was always a band of oxide around the exposed silicon area that was quite free of spurious silicon crystallites. This latter observation is particularly intriguing since it extends the hope that with proper precautions masking can be much more versatile than it presently is. EXPERIMENTAL PROCEDURE Silicon substrates oriented to within 1.5 deg of a (111) plane were prepared by etch polishing lapped

Jan 1, 1967

"In the spring of 1927, six members of the American Institute of Mining and Metallurgical Engineers met for dinner at the Chemists' Club in New York to discuss the possibility of setting up a committee within the Institute to further the current interest in the science of steelmaking. Attention to this subject had been crystallized by a symposium held by the Faraday Society in 1925. After a prolonged discussion, ranging from thermodynamics to slag conditioning, it was decided to approach the Institute with the request that a standing committee on "The Physical Chemistry of Steel Making" be set up. This committee proposed to promote scientific and practical papers on the subject, and was designed to cooperate with the Open Hearth Committee of the Institute in bringing scientific developments to the attention of open-hearth operators throughout the country. . . . "As the life of the [Physical Chemistry of Steelmaking] Committee lengthened and general interest in the technical phases of steelmaking grew, it .became evident that there was a distinct need for a book that might serve the open-hearth interests to better advantage than standard texts whose scope is necessarily wide and whose detailed exposition of the open-hearth process is, therefore, somewhat limited. With this thought in mind, the Committee, after some years of consideration and debate, embarked on the venture of writing a manuscript on 'Basic Open Hearth Steelmaking'." The foregoing paragraphs, taken from the introduction by C. H. Herty, Jr. to the first edition, well describe the circum- stances which led to the publication of “Basic Open Hearth Steelmaking” in the spring of 1944. The book consisted of nine- teen chapters contributed by twenty-three authors and edited by the staff of Alloys of Iron Research and T. S. Washburn, H; M. Larsen, and J. S. Marsh with Frank T. Sisco as consulting editor. The Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME, made financial grants; steel companies and other organizations supported the publication by contributing time and expenses of staff members in their capacity as authors or editors. The volume was sponsored by the Seeley W. Mudd Memorial Fund and appeared under the

Jan 1, 1964

"In the spring of 1927, six members of the American Institute of Mining and Metallurgical Engineers met for dinner at the Chemists' Club in New York to discuss the possibility of setting up a committee within the Institute to further the current interest in the science of steelmaking. Attention' to this subject had been crystallized by a symposium held by the Faraday Society in 1925. ' After a prolonged discussion, ranging from thermodynamics to slag conditioning, it was decided to approach the Institute with the request that a standing committee on "The Physical Chemistry of Steel Making" be set up. This committee proposed to promote scientific and practical papers on the subject, and was designed to cooperate with the Open Hearth Committee of the Institute in bringing scientific developments to the attention of open-hearth operators throughout the country... . "As the life of the [Physical Chemistry of Steelmaking] Committee lengthened and general interest in the technical phases of steelmaking grew, it became evident that there was a distinct need for a book that might serve the open-hearth interests to better advantage than standard texts whose scope is necessarily wide and whose detailed exposition of the open-hearth process is, therefore, somewhat limited. With this thought in mind, the Committee, after some years of consideration and debate, embarked on the venture of writing a manuscript on `Basic Open Hearth Steelmaking'." The foregoing paragraphs, taken from the introduction by C. H. Herty, Jr. to the first edition, well describe the circumstances which led to the publication of "Basic Open Hearth Steelmaking" in the spring of 1944. The book consisted of nineteen chapters contributed by twenty-three authors and edited by the staff of Alloys of Iron Research and T. S. Washburn, B. M. Larsen, and J. S. Marsh with Frank T. Sisco as consulting editor. The Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME, made financial grants; steel companies and other organizations supported the publication by contributing time and expenses of staff members in their capacity as authors or editors. The volume was sponsored by the Seeley W. Mudd Memorial Fund and appeared under the

Jan 1, 1951