Search Documents

By H. A. Jr. Koch, C. A. Hutchinson

Miscible phase displacement of oil from reservoirs has been emphasized in the past few years. The reason for this emphasis lies in the high oil recovery attainable by this process. Removal of capillary effects in the reservoir leads to recoveries approaching 100 per cent in the area contacted by the miscible phase. The miscible slug process is one means of obtaining a miscible displacement. Here a band or slug of I,PG is injected into the reservoir prior to gas injection. The idea is to maintain the band of LPG "wedged" between the gas and oil phases and thus achieve a miscible phase displacement. A second method lor achieving miscibility is through the injection of a gas which is not miscible with the reservoir fluid but which develops a zone of miscibility in [he reservoir through mass trans-ier with the reservoir oil.' This mass transfer results in either an enrichment of the lean injected gas by intermediates from the oil or an enrichment of the oil by intermediates from a rich injection gas or one that has been enriched on the surface by LPG addition. We are interested here in discussing the process in which miscibility is developed at the displacement front by the evaporation of interrnediatcs from the oil phase into the gas phase. This process "builds up" its own slug of miscible material at the displacement front and therefore does not require the injection of LPG to obtain miscibil-ily. Each process has its own area of applicability. Generally, the high pressure gas process is applicable only with reservoir fluids which con-!ain a high concentration of inter- mediates. If the high pressure gas process is technically feasible at pressures less than 4,500 psi, it is probably more desirable economically than the slug process. The slug process has broad applicability in the shallower reservoirs and with reservoir fluids which contain a relatively low concentration of LPG and natural gasoline constituents. This paper deals with some new concepts of the high pressure gas injection process where it is proposed that flue gas can be substituted for hydrocarbon gas without sacrificing our goal of miscibility. MECHANISM Introduction Considerable effort has been devoted to study of the mechanics ot the high pressure gas injection proc-one generalization result-ing from some of these studies was that the composition of the injected gas is relatively unimportant in establishing the miscibility pressure* for a given reservoir fluid. This generalization is correct for the composition range of gases typically encountered in the field. Two such gases are a gasoline plant tail gas containing 85 per cent methane and 15 per cent ethane, and a field separator gas containing 70 per cent methane and 30 per cent heavier components. The most important factor which sets the miscibility pressure in the operation is the reservoir fluid composition, particularly the concentration of LPG-natural gasoline constituents. The injected gas is the agent by which the LPG-natural gasoline constituents are concentrated at the displacing front to create a miscible displacement. Based on these results, it appeared feasible that some inexpensive gas, such as flue gas, might be substituted for hydrocarbon gas for use in the high pressure gas process. A re-examination of the phase relations of the high pressure gas injection process should clarify the principle behind using flue gas (essentially nitrogen) as an injection gas. Three Component Diagram The phase relations of the high pressure gas injection process have been illustrated by the use of the three component diagrams.'," In Fig. 1 we have arbitrarily represented the multi-component reservoir system by three components; methane, ethane through hexane, and heptanes plus. The solid curve ABC is the phase boundary curve. It represents the locus of compositions which have fixed saturation pressure at a fixed temperature; the lower branch AB shows bubble point compositions, the upper branch BC, the dew point compositions. Point B is the coniposition of the critical mixture at this temperature and pressure. The dashed lines (tie lines) connect vapor and liquid compositions which are in equilibrium. Let us consider Reservoir Fluid D which we wish to displace in 21 miscible manner by gas injection. Let us further restrict the discussion to the case where miscibility between an injection gas and the reservoir fluid at the displacement front is developed by gas enrichment in the reservoir. For this case, any gas whose composition lies between Points C and E on the right side of the three component diagram can be used to give a miscible displacement of Reservoir Fluid D. This is true because the more mobile injected gas moves faster than the displaced oil and is in continuous contact with virgin oil at the displacement front. This leads to a continuing enrichment 01' the gas at the displacement front by evaporation of the C, - C,

By Donald J. Drinkwater, M. C. Fuerstenau

Many important contributions to the more fundamental aspects of mineral processing have been made this past year. Mular1 researched the flotation characteristics of pure zinc oxide and also samples that had been doped with Al+++ and Cu++. Correlation of the response of pure zinc oxide to oleate flotation with a calculated zpc (from solution equilibrium) suggests that adsorption of oleate ion is coulombic in nature. Doping the sample with Al+++ (which will make the ZnO more n-type) had a marked effect on the maximum value of pH at which 50% recovery was obtained at constant collector addition. That is, when 0.5 mole percent Al+++ was added, the pH for 50% recovery was reduced by about four units. Treatment with Cu++ was found to have little effect on the flotation response of zinc oxide, even for additions of one mole percent. Since the zero points of charge of the Al+++ doped powders were not measured, it was not possible to correlate flotation data of these samples directly with charge phenomena.

Jan 2, 1966

By R. D. Saltsman

This paper deals with the evolution of a test procedure devised to totalize a coal's ignitibility, its degree of caking, and its coke reactivity and the development of a method for assigning proper combustion indices to stoker coals. The application of this type of work to stoker design is also discussed. It is believed that this work may be the prelude to understanding the effect of various petrographic constituents on the combustion characteristics of a coal or a blend of coals. The inadequacy of our knowledge of the coal combustion process has long been recognized. This was expressed very well by Spicer and Finney.1 "The control of combustion processes in industry and the design of the equipment necessary for efficient burning to take place have always been very much branches of an industrial art rather than of an exact science. This has been especially true of the utilization of coal, a substance so heterogeneous and complex in character that all too little is known about its chemical and physical composition." During the past several years one branch of coal utilization, that of high temperature carbonization, has made significant advances from being an art into being an exact science. This has been accomplished by the development of petrographic techniques for identifying, measuring, and determining the thermal properties of the organic materials which affect the carbonization of coal and the correlation of this information with a pre-existing standard of coke quality, the stability index. The success in using petrographic analysis for predicting the coking properties of coals and their blends suggested that petrographic techniques might be applied to the combustion process for predicting the combustion characteristics of coals. Certainly the different organic entities2 influence the combustion characteristics of a coal as they influence its coking properties. If it were possible to predict combustion characteristics from an analysis of a coal's petrographic composition, it would seem logical that an intelligent investigation could then be made into methods of altering stoker coals to improve their combustion characteristics. The successful application of petrographic analysis in the field of high temperature carbonization was made possible by the pre-existence of the stability index, which is a numerical value of coke quality. The quality of combustion is determined by the sum of the effects of the ignitibility, the caking, and the coke reactivity characteristics of a coal. While the literature is filled with papers reporting the correlation of various analyses to the ignitibility, or to the caking, or to the coke reactivity characteristics of coals, none of these earlier studies could be related to one index. The lack of a single index for combustion quality precluded the application of petrographic techniques for predicting combustion characteristics. SELECTION OF THE COMBUSTION TEST EQUIPMENT The primary prerequisite of any test developed to evaluate the relative performance of stoker coals must reflect the three characteristics of the coal burning process: 1) ignitibility, 2) degree of caking, and 3) coke reactivity. The widespread variations in these combustion characteristics of the available stoker coals are well known. The ignitibility, which has been defined as that characteristic which determines the ease with which the fuel may be brought to a condition of self-supporting active oxidation, varies from where a coal is deemed to be flashy to the opposite extreme of being fireproof. The ignitibility of a coal influences its ability to pick-up from hold fire, greatly affects the degree of bed stability during swing loads, and is a factor in determining the average burning rate obtainable on a given grate. The caking characteristic affects the degree of bed porosity during the devolatilization period, and coals are classified on a scale varying from free burning to highly caking. Caking is not synonymous with bed swelling since a bed may swell two to three times its normal depth during the period of devolatilization yet remain very porous, allowing an efficient and high rate of combustion to take place. Caking is melting

Jan 1, 1964

By N. Pessall, A. D. McQuillan

The phase relalionsllips in an isothernzal section of the Ti-Zr-H system at 750°Chave been investigated by measurement of hydrogen equilibrium pressures. The resulting diagram indicates that the hydride phase has an anomalously wide range of homogencity extending from 66.6 to 30 at. pct H in alloys containing about 15 al. pet Zr. Measurement of the heat of solution of hydrogen as a function of alloy composition in ß-phase alloys indicates no anomalous behavior in the region of 15 at. pet Zr, and suggests that the extensive range of homogeneity in the hydride phase at about this composition must he attributed to an enhanced stability of the, hydride phase. THE manner in which titanium and zirconium react with hydrogen and the constitutional diagrams of the two metal-hydrogen systems are qualitatively very similar,'-6 as can be seen from Fig. 1 which shows the constitutional diagrams of the two systems. Quantitatively, however, there are some differences. For example, the exothermic heat of solution of hydrogen in ß titanium is smaller than that in ß zirconium, and consequently the equilibrium hydrogen pressure of a Ti-H alloy is higher than a Zr-H alloy at the same temperature and hydrogen concentration. Other differences manifest themselves in the hydride phases which exist at high hydrogen concentrations. In the Ti-H system, above room temperature, there exists only a single hydride phase in which the metal atoms are arranged on a fee lattice, but in the zirconium system there are two hydrides, and whereas the hydride of lower hydrogen concentration has a fee structure, the higher hydride has a face-centered tetragonal structure. The tetragonal hydride retains its stability up to temperatures in excess of 450oC.7 From the foregoing, it would be expected that the constitutional diagram of the ternary Ti-Zr-H system would have a very simple form, especially as titanium and zirconium are completely miscible in both the a and ß forms.8 The present work, which consists of a study of an isothermal section of the ternary system, was carried out in order to check the assumption frequently made that the electronic structure of the two metals and the mechanism by which hydrogen is held in solution in the metals is the same for each. Although this proved largely to be true, certain inter esting and unexpected features of the ternary system emerged which must be explained before we can really say that the reactions of titanium and zirconium with hydrogen are fully understood. EXPERIMENTAL PROCEDURE The most convenient method of studying hydrogen-metal systems is by the measurement of the hydrogen pressure in equilibrium with the hydrogen dissolved in the metal as a function of hydrogen concentration and temperature. In binary systems, the results are easily interpreted in terms of alloy constitution, since two-phase regions can be recognized by the fact that the hydrogen pressure at constant temperature does not vary with the hydrogen concentration in the alloy when it is in the two-phase condition. This criterion does not apply in ternary systems, but there is usually a marked change of slope in the isothermal pressure-composition curves when a phase boundary is crossed, and with care, and a knowledge of the limiting binary systems, the phase structure of the alloys can usually be deduced. In the

Jan 1, 1962

By Albert F. J. Bordeaux

Alluvial gold was first discovered in Guiana in 1852, in the sands of the Arataye river, by Paulino, a Braziliaii convict. During the following years, gold was found also in the rivers Orapu, CirubQ, etc. In 1873 the famous placers of the Sinnamary system were opened: Saint-Elie, Dieu-Merci, Adieu-Vat, and Couriege. This group of mines has produced nearly $10,000,000, according to official records, not including the gold that escaped the taxes. The discoverer was a mulatto named Vitalo. Except in a few rich spots, the gold was rather evenly distributed along the creeks. In one instance, gold was found in the red dirt from the slope of a hill, which, after transport to the creek, gave an amount of 150 kilograms. The placers of the Mana system, Enfin, Elysee, Pas-Trop-Tot, date from 1878, and their production has been about %g5,000,000. In 1888, the Awa placers, along the boundary bet.ween the French and Dutch Guianas, on the Maroni and its tributaries, were discovered. They have yielded $12,000,000. The only industrial company, the Dutch Guiana Freiich Minillg Co., produced in 15 years about 2,500 kg. of gold, worth $1,500,000. From 1893 dates the famous Carsewene discovery, in territory then in dispute between France and Brazil. A settlement was made recently in favor of Brazil, by arbitration of the Switzerland State Council. Carsewene is said to have produced about $18,000,000 in six years (1894-1900), but not even one-fourth of tho production went through French Quiana and

Jan 1, 1911

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7

Jan 1, 1923

By Roshan B. Bhappu, Raul A. Deju

A method is proposed by which the chemical reactions between water and a silicate bed can be related to equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved, and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented. The knowledge of surface reactions at the water-solid interface is of critical importance in extractive metallurgy. This is especially true in regard to the froth-flotation process of mineral concentration and all phases of hydro metallurgical recovery of metals. Similarly, the problem of ground-water contamination is one of growing concern, not only because of the increasing demands on our sources of supply but also because of the increasing necessity to find vehicles of waste disposal. The hydrochemistry of waste waters must be understood to exploit and develop such resources properly. To understand these problems, it is necessary to obtain a better insight into the reactions that take place between water and a solid packed bed. To do this, we will develop here in a theoretical model that predicts the fate of a chemical species in solution as it reacts with a silicate bed through which the liquid percolates. The treatment will be one-dimensional in nature and will not include dispersion. Experiments will also be presented to substantiate the theoretical model, using the silicate minerals listed in Table 1. This paper is preliminary in nature and is part of a larger study of the surface chemistry of the silicate-water interface. Mechanism of Surface Reactions In a previous paper,' the authors discussed the properties of various silicate minerals from a mineralogical standpoint. Now efforts will be made to study the reactions that occur when these minerals are put in contact with water. The reactions occur almost entirely in the surface layer of the mineralsa and are termed sorp-tion reactions. In this study sorption denotes the composite of all physical adsorption and chemical adsorption occurring between the silicate surface and the water in contact with it. A model of sorption as seen from a chemical-bond standpoint is presented below. On the basis of this model, the surface reactions between deionized water and a silicate mineral can be studied. Sorption Model: It is known that as the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, the oxygen-to-metal bonding increases. Upon the fracturing of a silicate-mineral crystal, the oxygen-metal bond breaks more easily than the stronger oxygen-silicon bond, resulting in a negatively charged surface. Then, if the mineral is immersed in a liquid containing hydrogen ions, the negatively charged surface should tend to be neutralized by hydrogen ions from solution, resulting in a change of the solution pH. Thus, an increase in the degree of sorption of hydrogen ions must occur as the oxygen-silicon ratio in the crystal structure increases. Also in a previous paper,' the authors found that for a given silicate mineral the change of pH with time is given by

Jan 1, 1971

By F. A. Crossley

The additions: o, Sn, Zr, Cb, Mo, and V were studied for their effects on the a/a + Ti3A1 boundary of Ti-A1 base ternary alloys. These additions were chosen because of their importance to commercial titanium alloy practice—oxygen as the major impurity (in terms of influence on mechanical properties) and the others as major alloying additions. The composition and temperature ranges of investigation varied according to the system as shown in Table I. The principal means of investigation was light-microscopy. The basis of the ternary studies was the recently determined titanium-rich end of the Ti-A1 system.' MATERIALS, METHODS, AND PROCEDURES Ingots were prepared in 15 g size for all alloys except those of the Ti-Al-Mo and Ti-A1-V systems which were prepared in 20 g size. These alloys were prepared from high-purity, electrolytically refined titanium obtained from the Bureau of Mines, Boulder City Metallurgical Laboratory, Boulder City, Col., and Chicago Development Corp., Riverdale, Md., for the 15 g and 20 g ingots, respectively. The alloying additions were obtained from commercial sources, and were at least of 99.9 pct purity, except the V-15 wt pct A1 master alloy for vanadium additions. This alloy was of 98.2 pct purity; the major impurities were 0.37 wt pct Fe and 0.38 wt pct Si. The ingots were prepared by multiple melting in a nonconsum-able-electrode arc furnace. The ingots were covered with Markal coating "CR-T22" (Markal Co., Chicago) to protect them from scaling. Markal coating is applied as a slurry of solids in a volatile carrier liquid. The coated article is air dried. Upon heating to the hot working temperature the coating fuses to form a glassy, protective film. The ingots were heated to 1000°C and rolled to 0.16 in. thickness, reheating after each pass. The glassy film was removed by sand blasting. Ten mils were removed from all surfaces by grinding and/or pickling (3 pct HF, 30 pct HN03, balance water). Grinding was always followed by pickling to remove traces of the grindmg medium. Hydrogen removal was accomplished by vacuum annealing at 1000°C for 2 hr to a final pressure of about 0.02 µ Hg. This was followed by annealing in evacuated Vycor bulbs (800°C, 2 hr, ice brine quenched (IBQ)) in order to maximize ductility. The materials were then lightly pickled and cold rolled to 0.12 in. thickness or cracking, whichever occurred first. After rolling, 1/2 by 1/4 in. specimens were cut for the equilibration anneals given in Table 11 and carried out as previously described.1 Final polishing of the specimens for metallographic examination was done by electrolytic means. Specimens were first examined without etching under bright field and polarized light illumination, for this is the only means of detecting the "two-phase" phenomenon.1,2 The term "two-phase syndrome" refers to Ti-A1 al-loys which appear on the bases of their chemical, phys-ical, and mechanical properties, to be two-phase, but are actually single phase and inhomogeneous in composition. Since processing and heat treatment of the alloys of the first group were completed before the two-phase syndrome was discovered, a number of the specimens were found to exhibit this phenomenon—80 pct of those of the Ti-Al-Zr system, 5 pct of those of the Ti-Al-Sn system, 30 pct of those of the Ti-Al-Zr system. The affected specimens were homogenized by heating above the ß transus temperature and quenching. The heat treatment and working schedules to accomplish this are given in Table 111. After rolling, specimens were pickled (3 pctHF, 30 pct HNO3 in water) to remove 1 to 2 mils from the

Jan 1, 1970

By Y. C. Liu, W. R. Hibbard

An aluminum single crystal cold-rolled from (110) [1121 essentially retains its initial orientation after 99.6 pct reduction in thickness. The orientation of the recrys-tallized grains of this material can be described in terms of crystallographic rotations about principal poles of deformation texture. DURING the study of the recrystallization of a copper single crystal cold-rolled from a (110) [112] initial orientation, the orientation of the re-crystallized grains could be derived by a 30" rotation of the orientation of the cold-rolled matrix about its <111> poles.&apos; The present investigation was undertaken to extend the work done on copper&apos; to an aluminum crystal also cold-rolled from a (110) [112] initial orientation. Experimental Procedure The procedure of this experiment was similar to that reported for copper.&apos; An aluminum (99.998 pct) single crystal rod* 1 % in. in diameter was grown in back-reflection technique.&apos; The specimen (1.20x 1.004x0.6787 in. thick) was then rolled along the [112] direction. The final thickness was 0.0028 in., giving a reduction in thickness of about 99.6 pet. Specimens were cut from the rolled strip with scissors, and approximately in. of disturbed metal was removed with Tucker&apos;s reagent. The rolling edge remained intact. The specimens were sandwiched between two graphite plates and annealed in a lead or lead alloy bath which was electrically heated. Pole figures were constructed using the techniques previously described.&apos; Specimens were electrolytically polished4 and etched with 47 pct HNO8, 50 pct HC1, and 3 pct of 48 pct HF. The electrolytic polishing method and etching reagent employed for aluminum specimens were not entirely satisfactory and the microstruc-tures could not be studied in any detail. Results and Discussion The octahedral pole figure of cold-rolled aluminum strip is plotted in Fig. 1. The <111> poles spread in the transverse direction approximately 8" for the highest intensity areas. The spread in the transverse direction can be related to a rotation about two <110> directions lying in a plane containing the rolling direction and rolling plane normal. The two <110> directions and a scale of rotation for the <111> poles are shown in Fig. 2. The amount of rotation is consistent for three of the four <111> poles, about 35" to 40". The discrepancy for the fourth pole is believed to be due to limitations of the film technique. Alternate inter-

Jan 1, 1956

By Edgar Kidwell

To any one acquainted with the practical conditions surrounding the mining engineer and mine-manager, especially in this country, the presentation to the American Institute of Mining Engineers of a paper on the above subject will need no explanation. The members of this profession are continually called upon to design and erect, both above and underground, structures which involve the use of beams. Not to mention the various buildings connected with large mining operations, I need only refer, in support of this statement, to trestles, derricks, headworks, etc., on the surface, and to timbered stations and other spaces of large span in the mine-workings. Notwithstanding the rapidity with which iron and steel are replacing wood in the construction of large buildings, there will always be cases in which the use of metal will be unadvisable. Especially will this be true in districts remote from large cities. Works of temporary character will continue to use timber. High freight-charges, the liability of delays in delivering iron, and the temporary character of many of the structures, will for many years to come make it advantageous for the mines west of the Mississippi and on Lake Superior to construct their buildings almost exclusively of wood. The timber-resources of the country are decreasing so rapidly that already the engineer finds difficulty at times in obtaining beams of large size. This difficulty will steadily increase, and will force the constructor to resort more frequently to built-up beams, such as have long been used in Europe, owing to the difficulty of obtaining there such large sizes of timber as have

Jan 1, 1898

By T. W. Peterson, J. W. White, E. E. Krist

In developing a minicomputer application for an industrial grinding circuit, the control program is usually coded and the compilation is debugged on a remote access computing system. Final debugging must wait for installation of the minicomputer. This work reports on an alternative. Here both compilation and execution bugs are eliminated before the hardware is installed by testing the control program against a dynamic simulation. Attention is directed toward development of a particular real-time control program for an industrial wet grinding circuit in a copper concentrator. Specific data were supplied by the Anamax Mining Co. for a grinding division consisting of a rod mill followed by two ball mills in parallel. This information was used to set up a plausible model structure.

Jan 1, 1977

By H. R. Thresh

An oscillational vis cometer has been constructed to measure the viscosity of liquid metals and alloys to 800°C. An enclosed cylindrical interface surrounds the molten sample avoiding the free surface condition found in many previous measurements. Standardization of the apparatus with mercury has verified the use of Roscoe&apos;s formula in the calculation of the viscosity. Operation of the apparatus at higher temperatures was also checked using molten lead. Extensive measurements on five different samples of zinc, of not less than 99.99 pct purity, indicate i) impurities at this level do not influence the viscosity and ii) the apparatus is capable of giving reproducible data. The variation of the viscosity ? with absolute temperature T is adequately expressed by Andrade&apos;s exponential relationship ?V1/3 = AeC/VT , where A and C are constants and V is the specific volume of the liquid. The values of A and C are given as 2.485 x 10-3 and 20.78, 2.444 x 10-3 and 88.79, and 2.169 x 10-3 and 239.8, respectively, for mercury, lead, and zinc. The error of measurement is assessed to be about 1 pct. Prefreezing phenomena in the vicinity of the freezing point of the zinc samples were found to be absent. AS part of an over-all program of research on various phases of melting and casting nonferrous alloys, a systematic study of some physical properties of liquid metals and their alloys was undertaken in the laboratories of the Physical Metallurgy Division.1,2,3 The most recent phase of this work, on zinc and some zinc-base alloys, was carried out in cooperation with the Canadian Zinc and Lead Research Committee and the International Lead-Zinc Research Organization. One of the properties investigated was viscosity and the present paper gives results on pure zinc; the second part, on the viscosity of some zinc alloys, will be reported separately. Experimental interest in the viscosity of liquid metals has virtually been confined to the past 40 years. The capillary technique was already established as the primary method for the viscosity of fluids in the vicinity of room temperature; all relevant experimental corrections were known and an absolute accuracy of 1 to 2 pct was possible. Ap- plication of the capillary method to liquid metals creates a number of exacting requirements to manipulate a smooth flow of highly reactive liquid through a fine-bore tube. Consequently, the degree of precision usually achieved in the high-temperature field rarely compares with measurements on aqueous fluids near room temperature. However, the full potential of the capillary method has yet to be explored using modern experimental techniques. As an alternative, many investigators in this field have preferred to select the oscillational method. Unfortunately, the practical advantages are somewhat offset by the inability of the hydrodynamic theory to realize a rational working formula for the calculation of the viscosity. In attempting to overcome this restriction many investigators have employed calibrational procedures, even to the extent of selecting an arbitrary formula for use with a given shaped interface. However, where calibration cannot be founded on well-established techniques, the contribution of such experiments to the general field of viscometry is questionable. A critical appraisal of the viscosity data existing for pure liquid metals reveals a somewhat discordant situation where considerable effort is still required to establish reproducible and reliable values for the low-melting point metals. The means of rectifying this situation have gradually evolved in recent years. Here, the theory of the oscillational method has undergone major advances for both the spherical and cylindrical interfaces. The basic concepts of verschaffelt4 governing the oscillation of a solid sphere in an infinite liquid have been adequately expressed by Andrade and his coworkers.5,6 Employing a hollow spherical container and a formula, which had been extensively verified by experiments on water, absolute measurements on the liquid alkali metals were obtained. The extension of this approach to the more common liquid metals has been demonstrated by culpin7 and Rothwel18 where much ingenuity was used to surmount the problem of loading the sample into the delicate sphere. Because of the elegant technique required to construct a hollow sphere, the cylindrical interface holds recognition as virtually the ideal shape. On the other hand, loss of symmetry in one plane increases the complexity of deriving a calculation of the viscosity. The contributions of Hopkins and Toye9 and Roscoe10 have markedly improved the potential use of the cylindrical interface in liquid-metal viscometry. The relatively simple experi-

Jan 1, 1965

Jan 1, 1943

Jan 1, 1943

W. S. GRESLEY, Erie, Pa. (communication to the Secretary): A six-entry method of opening coal-mines is, or was a short time ago, practiced in the Connellsville coal-region; but Dr. Chance&apos;s method has a novel aspect; for while in the Connellsville region the main pillars are formed outside of two pairs

Jan 1, 1901

By W. R. Johnson

In the spring of 1935 the writers undertook to compare the geomagnetic and direct-current earth-resistivity methods of tracing a concealed dike along its strike. As far as they are aware no such direct test has been attempted.# The area surveyed lies along United States Highway number 15 about one and one-half miles east of Chapel Hill, North Carolina, and northeast of Bolin Creek (Fig, 1). To the south of the highway is the flood plain of Bolin Crook, and to the north is a hill that rises almost to the elevation of Chapel Hill. A diabase dike, which strikes slightly west of north, out-crops in a. gully just south of the highway. Southward it has been covered by alluvium but northward outcrops again on the southeastern slope of the hill north of the highway. South of the highway the country rock is Triassic shale and sandstone, the northern limit of which is slightly north of the road. On the Geological Map of the United States I the pre-Triassic formations are shown as lower Glenarm and assigned a pre-Cambrian age. Since the ago of the Glenarm has been called into question in Pennsylvania 2, the writers prefer not to commit themselves as to the ago of these rocks further than to say that they are definitely pre-Triassic.

Jan 1, 1937

By Robert G. Woolery, S. Ramachandran, James A. Weber, Donald J. Hansen

Union Carbide began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.40 kg U308 /t) (0.80 lb U308) were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leaching project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. The operators were most generous in allowing us to visit their site and in answering our questions. They were also helpful in discussing the problems associated with heap leaching. Their experience confirmed our belief that it was possible to operate a heap leach profitably on material too low grade for conventional milling.

Jan 3, 1978

By S. C. Langdon, Henry S. Rawdon

The following note describing the behavior of copper under rather unusual conditions is offered for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning, as well as softening it. It is well known that metals may be rendered very brittle by electrolytic action in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear 2 similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. TO demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 801" C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for several minutes. When removed from the bath, cooled, and tested for brittleness by bending the specimen back and forth, while clamped firmly at one end in a vise, the copper rod was found to be very brittle, as compared with a rod of the same length of the untreated copper tested

Jan 1, 1921

By Sheldon Rideout, E. L. Kamen, B. S. Lement, Paul A. Beck, W. D. Manly

The 1200°C isothermal sections of the following ternary phase diagrams were investigated: Cr-Co-Nil Cr-Co-Fe, Cr-Co-Mot and Cr-Ni-Mo. In all these systems the u phase was found to form extended solid solutions. Two new ternary phases of unknown structure were identified. The existence range of intermediate phases of transition elements was correlated with 3d electron vacancy concentrations. THE occurrence of extensive ternary d solid solutions in the Cr-Co-Ni and in the Cr-Co-Fe systems was described in a brief note.&apos; More recently d- solid solutions were also found in the Cr-Fe-Mo system by two independent groups of investigators.2,3 The existence of binary d phases in the V-Co and V-Ni systems, predicted in ref. 1, was experimentally discovered recently by Duwez and Baen and independently by W. B. Pearson, J. W. Christian, and W. Hume-Rothery.5 Duwez and Baen stated two general conditions for the occurrence of the d phase in alloys of the transition elements: "(1) The atomic diameters of the two metals do not differ by more than 8 per cent. (2) One of the two metals has a body-centered cubic structure while the other is face-centered cubic, at least in one of its allotropic forms." In the course of an extensive research program conducted at this Laboratory under the sponsorship of the NACA, several ternary systems, containing d solid solutions and also certain new ternary phases, were investigated. The present report describes the investigated portions of the 1200°C isothermal sections of the following ternary phase diagrams: Cr- Co-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo. It was found that the range of existence of the d phase in these four ternary systems, as well as in one of two ternary systems which were investigated by others, can be fairly consistently described in terms of electron vacancy concentrations. This supports the suggestion of Sully and Heal" that the d phase is an electron compound. Experimental Procedure The ternary alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. Lot analyses of the metals used are given in Table I. Specimens of all alloys were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting mainly of

Jan 1, 1952

By Jack R. Elenbaas, Donald L. Katz

A radial turbulent flow formula has been developed which permits the computation of the pressure drop for radial flow in gas wells whether the flow is laminar, turbulent, or partially laminar and partially turbulent. Using the formula a complete back-pressure curve has been calculated and analyzed by a comparison with existing back-pressure curves. A procedure is presented for computing the permeability of the porous media when the porosity, sphericity and average particle diameter are known. Introduction Recent studies on the flow of fluids through porous media have provided new methods for computing flow under turbulent conditions. The present study was initiated as an investigation of pressure -drop computations for flow through porous sands in gas wells and as an analysis of present-day back-pressure tests. Although laminar flow exists in the producing formation of gas wells under normal flow rates, turbulent flow does take place adjacent to the well bore. As the flow rate is increased, turbulent flow exists further and further into the producing formation and under open-flow conditions in relatively deep wells a considerable portion of the flow through the sand will be turbulent. In order to calculate a complete backpressure curve for relatively deep wells without resorting to extrapolation of curves drawn from data obtained in back-pressure tests or calculations made in the completely laminar region, it was necessary to have some means of calculating pressure drop for flow through porous sands under turbulent conditions.4.6 As a result, a radial turbulent flow formula was derived from the equations recently presented by Brownell and Katz.1 A rigorous solution of this equation involves a trial and error graphical integration. By making the assumptions of average viscosity, temperature and compressibility factor of the flowing gas, it was possible to graphically integrate the relation for the general case of radial flow of gases through the porous sand of gas wells. A chart has been prepared relating the value of the integral to the radius of the well bore and to the Reynolds number of the flowing gas. The chart actually performs the graphical integration and the solution of the formula is then reduced to a simple trial and error calculation. A typical back-pressure curve is calculated to show the transition from laminar to turbulent flow. This paper will briefly describe the pro-cedurcs for computing flow through porous media, including a method for predicting sand permeability from porosity and grain size and shape. Flow through Porous Media Brownell and Katzl recently reported a correlation for computing flow of fluids through porous media by the use of an enlarged Reynolds number and friction factor in which the porosity of the bed is included as an additional prime variable. The enlargcd Reynolds number com-

Jan 1, 1948