Search Documents

By Manuel Eissler

INTRODUCTION THE history of copper metallurgy in Japan goes back into remote ages, of this there is abundant proof, and that the working of this metal is closely connected with the artistic development of this nation is evidenced by some of the glorious monuments which have been produced by these ancient metal workers. The traveler sees to-clay in a perfect state of preservation bronze statues 150 ft. high, and over, 300 ft. in width, and 170 ft. in depth, delicately chased and beautifully marked, and when one reflects that some of them date back to the eighth century A. D., the question naturally suggests itself, how did these ancient metallurgists with their crude and primitive appliances accomplish this stupendous task? The bodies of these images are formed of bronze castings 10 to 12 in. thick, which were gradually built up and soldered together, but other pieces of magnitude, like the heads and other portions of the body are single castings. In many cases another method of construction must have been adopted. The walls of the molds were gradually built up and as the lower portion of the castings cooled, the walls were raised higher and higher and fresh metal must have been added, instead of constructing the whole mold first and then making the casting in one piece. There are still traces of substantial gilding visible on these statues, and how the pious Buddhist priests who were the constructors of them got the precious metal, is preserved in legendary tales.

Jan 11, 1914

By Y. C. Liu

The orientation relationship between the dejormation and recrystallization textztres of binary Cu-P alloys of high phosphorus content was observed to he a ± 14-deg (110) rotation. According to the ori-ented-gvowth hypothesis, the same relationship should exist between a successfully flowing pain and the strained single-crystal matrix of alloys of corresponding composition. The orientations of thirty successfully growing grains were obtained in a Cu-1.0 at. pct P alloy. Both a conventional analysis and the more detailed analysis advanced in the present study demonstrate that the observed orientation relationship is not comparahle to that predicted by the oriented growth hypothesis. IT has been shown experimentally that the formation of recrystallization textures in metals may be explained on the basis of the oriented-growth hypothesis. This conclusion is based primarily on the results of cooperative experiments carried out by various investigators in aluminum. Beck and HU' suggested that the orientation relationship between the recrystallization and deformation textures of aluminum is a 38-deg(111) rotation. A similar relationship, i.e., a 40-deg(111) rotation, was observed between the primary and secondary recrys-tallization textures.' Since the secondary grains result from a process of selective growth, this naturally implies that the same mechanism is also responsible for the formation of the primary re-crystallization texture from the deformed matrix. Further evidence was provided by the experiments of Liebmann, Liicke, and Massing3 and Yoshida, Liebmann, and Lucke.4 They observed that grains which could successfully grow into strained aluminum single crystals invariably exhibited the same orientation relationships with their matrix. Thus, regardless of other opinions,5'9 these results offered good evidence in favor of the oriented-growth hypothesis. In order to examine broader applications of this oriented-growth hypothesis, experiments should be carried out in metals other than aluminum. In a recent investigation on the recrystallization textures of binary copper alloys with phosphorus, arsenic, and antimony,7 it was found that the predominant recrystallization components were related to the deformation textures by a (110) rotation. The (110) rotational relationship is different from the (111) relationship generally proposed between the recrystallization and deformation components of other binary copper alloys. 1,8,9 Applying the observations made for aluminum, the oriented-growth hypothesis predicts that the orientation relationship of grains successfully growing into the strained single crystals of either one of these copper alloys should correspond to that observed in the textural study. Verification of this prediction would provide a critical test of general applicability of the oriented-growth hypothesis to the formation of recrystallization textures in fcc metals other than aluminum. The Cu-1.0 at. pct P alloy was selected in the

Jan 1, 1964

By John W. Cloud

IN 1877 the Pennsylvania Railroad Company removed an old bridge from its line at Duncannon, Pa., built intermediate piers and erected shorter spans of the Pratt truss type, which had previously been in use on another portion of the road. The design of this truss would not admit of diagonals larger than 1 5/8 inches diameter, and in order to stiffen the bridge somewhat steel rods were introduced for the main diagonals in the first and second panels, 1 5/8 inches and 1 3/8 inches diameter respectively. These rods were threaded without upsetting, and by the ordinary formulae the strains were of the same intensity upon both, viz., 16,000 pounds per square inch with the maximum loading. The other main diagonals in the truss are 1 5/8 inches diameter, and of iron. It was specified for the steel rods : Elastic limit, - 45,000 lbs. Tensile strength, - 80,000 lbs. Elongation, - 20 per cent. The steel was procured without difficulty, and it allowed a factor of safety of 2 3/4 at elastic limit, while a similar factor of 2 1/2 had for a long time been successfully used for iron. In the course of three years, from time to time, six of these steel rods broke, three of them being 1 3/8 inches in diameter, and three 1 5/8 inches in. diameter. The broken rods were tested, and three of them. analyzed at Altoona to ascertain the cause of failure, and what modi¬fications should be made in the steel for such service. Examination showed that all the rods were broken in detail close under the nut. The threads were well cut and properly rounded at the root. In testing the rods micrometer screws,. reading to .0001" with electric bell to signal the contact, were attached to the test pieces, and by this means the modulus of elasticity and elastic limit accurately obtained.

Jan 1, 1881

By Carl Allen

INTRODUCTION IN any discussion of mining one is repeatedly confronted with the difficulty of dealing with so many variable conditions. It is not an exact science and in the choice of a method each varying factor has a certain weight, which, in many cases, experience alone can determine. In mathematical terms, it is a function of many variables. A discussion of mining also loses much of its value unless, costs are considered, because the expectation of profit is the only excuse for carrying on mining at all. As conditions vary they cause fluctuations in cost and there are few operations to which a definite cost can be assigned. The character of the ore may make it difficult to drill, yet because of the ease with which it breaks the total cost of drilling and blasting may be low. In preparing this article the attempt has been, not to cover the whole field of mining, but to describe the different methods of stoping and mining which have distinct principles. In addition to this an effort has been made to show the advantage of dissecting the methods into their detailed operations and applying to these a mathematical study as an aid to the judgment in determining which is the best method to adopt, or in attempting to reduce the cost of a method already in use. Methods of mining include stoping, caving, and various methods of working large deposits which, in addition to the method of actually breaking the ore, require elaborate and definite plans of, development of the orebody. The ordinary methods of stoping are too familiar to all for any elaborate discussion, but it has seemed advisable to review the subject and give the principal advantages' and disadvantages of the different methods.

Jan 8, 1914

By Thomas Harris

This paper. was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the' reduction of indivi-dual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States. in order to consolidate the information de-veloped from the many hundreds of boiler tests on coals consumed by various coal¬burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal date, including description of coals used (with. sufficient space to- include first, second and third, preference) on--source of coal used,- complete-analysis and factors affecting choice of, coal used. 3. Plant data, divided into - A. Hand fired, B. Overfeed stokers,. . C. Underfeed stokers, D. Traveling grate stokers, E. Pulverized coal, and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency date and remarks.

Jan 1, 1933

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By R. A. Foos

During the radium boom in the early part of the twentieth century, the basic chemistry of uranium was fairly well defined. Uranium production has progressed from the status of a radium by-product to a very important industry. With the ever increasing need for more efficient and cheaper methods of processing uranium ores, new techniques are being developed. Since uranium and vanadium often occur together in nature, the latter element will also be considered. As production rates, costs, and certain aspects of uranium chemistry are still classified by the Atomic Energy Commission, these will not be discussed. Domestic uranium deposits, in general, are composed of the minerals carnotite, which contains hexavalent uranium, and to a lesser extent, pitchblende and uraninite, which contain tetravalent uranium. Carnotite also usually contains vanadium. The uranium and vanadium contents of these ores vary considerably. The ores currently processed on the Colorado Plateau assay from 0.2 to 0.4 pct U and from trace amounts to 5.0 pct V. On the other hand, the phosphate rock deposits of the southeastern U. S., from which uranium is also recovered, contain only about 0.01 to 0.02 pct; processing of the

Sep 1, 1956

A recent study estimates that a 10% improvement in the performance of wire rope used on draglines could save the US coal industry $2 million annually in rope costs. In addition, such an improvement could boost annual coal production by allowing the industry's draglines to remove an extra 1.5 million m3 (2 million cu yd) of solid overburden each year. These findings, although admittedly preliminary, suggest the magnitude of benefits that can be derived from a well-planned wire rope maintenance program.

Jan 3, 1978

By A. E. Lillstrom

IN the development of iron mines and production of iron ore from the Marquette range, drilling blast-holes is an important phase of the mining cycle. The ground drilled in ore production can be classified into two main categories, soft hematite and hard hematite or magnetite. Within these categories the material exhibits a wide range of penetrability by percussion drills. Development work encounters various types of rock. Slate and altered basic intrusives constitute the softer types commonly encountered. Harder materials are represented mainly by greywacke, quartzite, iron formation, and diorite. Prior to the first tungsten carbide trials in late 1947 and early 1948, hard-rock and ore drilling was done with steel jackbits starting at 21/4-in. diam. These were reconditioned by hot milling. Automatic or handcrank 31/2-in. drifters were employed, mounted on Jumbos, posts and arms, or tripods, depending upon the working place. With the exception of shaft sinking jobs where 55-lb sinker machines were and still are used with 1-in. quarter octagon steel, the other production and development mining utilized 11/4-in. round and Leyner-lugged steel. The following properties have been selected as typical examples wherein carbide bit applications have proved economical. The Mather mine "A" and "B" shafts and Cleveland-Cliffs Iron Co. mines are soft ore mines where insert bits are used in rock development only. The Greenwood mine, Inland Steel Co., Champion mine, North Range Mining Co., and Cliffs shaft mine, Cleveland-Cliffs Iron Co., are hard ore mines where all drilling is done with tungsten carbide bits. Mother Mine "A" Shaft In the Mather mine "A" shaft and other soft ore properties where only rock development work is done with the tungsten carbide bits, several types and makes of bits have been tried since early 1948. The greatest proportion of failures have been at the connection end, although the early trials with the 13 Series Carset 11/2-in. bit used in conjunction with 31/2 -in. automatic-feed drifters, showed an equal amount of shattered inserts. To combat this shattering, the 31/2 -in. drifters were replaced by 3-in. drifters, thus eliminating, for the most part, insert failures. However, the attachment end of the rod continued to be the main source of trouble. The greatest amount of failure was in the stud or at the upset section approximately 2 in. behind the drive shoulder of the rod. Heat treatment was changed several times as well as the composition of the alloy studs. Since this failed to correct the trouble, a decision was made to change to a heavier attachment section. Timken 11/2-in., type M, bits were then employed and showed an exceptional improvement. The rods are discarded when the thread contour shows sharpening or wear on the shoulder. It was also learned that the Timken insert did not show as rapid gage and cutting edge wear as did competitive makes, and footage per use increased by approximately 50 pct. Prior to the Timken trials the average life per bit at the Mather mine "A" shaft on 6-ft change chain-feed drifters was 500 ft, and the rod life at the connection end was 50 ft. The Timken bit with chrome-plated thread averaged 1200 ft, and rod life increased to as much as 500 ft. However, the life of the connection end was much better on shorter length drill rods or in places where machines with 34-in. change were used. The bit thread continued to be the point of ultimate failure with thread strippage, constituting the cause for discard of bits. In one of the new development headings, harder rock was encountered for approximately 800 ft, dropping the life per bit to a low of 90 ft with shank and thread life of rods dropping to approximately 125 ft average. The stripped bits were then welded to the rods, increasing the life per bit by 75 to 100 pct. The rod transportation for main level development was not a problem so intraset rods were tried. Intraset rods have tungsten carbide inserts set into the rods proper by the manufacturer and can be obtained with chisel or four point bits. This type of rod eliminates the need for any connection and the steel being a special alloy will show more feet drilled per rod. The first trial was made with eight rods, and final results averaged 350 ft per rod, six of the rods worked the life of the bit end, and two broke shanks at less than 50 ft. The preceding example showed a considerable improvement, so additional steel of the same type was purchased, but its use has been limited to main level drifting only, because of the handling problem involved in transportation of the complete rod to mine shops for resharpening. Further trials are being made on improving the life per detachable bit by chrome plating. To date, the chrome plating shows an improvement of approximately 100 pct. However, final results will not be known until the present long term trials have been completed. Mother Mine "B" Shaft In November 1947, tungsten carbide bits were first tried at the Mather mine "B" shaft. The use of 1%-in. Carset 13 Series bits, for drilling the 72-hole, 7-ft shaft round, decreased the drilling time from an average of 41/2 hr per round required with steel bits, to 2 hr with insert bits. The best drilling time for

Jan 1, 1952

By A. K. Chakravarti, A. Lihiri, G. G. Sarkar

One primary objective of India's third Five Year Plan is the expansion of coal production. The goal: boost present output of 45 million tons to 95 million tons by 1965--an increase of more than 100 pct!

Jan 7, 1961

By F. A. Schaufelberger

Early work on chemical precipitation of metals from metal salt solutions is reviewed. The chemistry and thermodynamics of precipitating copper, nickel, cobalt, and cadmium metals by reaction with hydrogen are discussed. Mechanisms of metal precipitation, nucleation, growth, and agglomeration are reviewed, as well as some solubility phenomena of gases and solids at elevated temperatures. Experimental data presented deal mainly with the reaction of copper sulfate solution with Hz.

May 1, 1956

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

Little information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger's," ' Kick's,%nd Bond's' theories. Theories by Bond and Wang," Lineau,' Hatch,' Roller," and others were not considered applicable. Those used in this investigation may be expressed mathematically as follows: [ ] The above equations were employed to determine values of KK, K for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement.

Mar 1, 1956

By H. W. McCue, Henry Rogatz

Oil.—In the Texas Panhandle, during the year of 1941, 647 oil wells were drilled with a total daily initial production of 133,435 bb1.—that is, 145 more oil wells than in the previous year, with a decrease in total daily production of 5752 bbl. On Dec. 31, 1941, a daily allowable of 116,766 bbl., which was an increase of 27 per cent over 1940, was assigned to the field to be produced from 5182 wells. The total amount of oil produced for the year was 27,904,846 bbl., making a cumulative total of 404,657,324 bbl. during the past 20 years. Gas.—During the year, 52 gas wells were drilled, having a combined open flow of 2.62 billion cu. ft. per day—that is, 40 less than the number of wells drilled in 1940, with an increase in the open flow of 217,100,000 cu. ft. per day. The gas

Jan 1, 1942

By Henry Rogatz, H. W. McCue

Oil.—In the Texas Panhandle, during the year of 1941, 647 oil wells were drilled with a total daily initial production of 133,435 bb1.—that is, 145 more oil wells than in the previous year, with a decrease in total daily production of 5752 bbl. On Dec. 31, 1941, a daily allowable of 116,766 bbl., which was an increase of 27 per cent over 1940, was assigned to the field to be produced from 5182 wells. The total amount of oil produced for the year was 27,904,846 bbl., making a cumulative total of 404,657,324 bbl. during the past 20 years. Gas.—During the year, 52 gas wells were drilled, having a combined open flow of 2.62 billion cu. ft. per day—that is, 40 less than the number of wells drilled in 1940, with an increase in the open flow of 217,100,000 cu. ft. per day. The gas

Jan 1, 1942

By Raja V. Ramani, Ralph W. Barbaro

This paper presents an application of a Mixed Integer Programming (MIP) model to the problem of locating a centralized coal preparation plant and determining the production schedule for the mines. The system used for illustrating model application is hypothetical but realistic. It consists of three mines, two potential preparation plant sites, heavy media processing plant, and one market. The goal is to maximize the total profit of the system while satisfying the coal delivery schedule over a three year period meeting both quantity and quality requirements (ash, sulfur, and heat content). In addition to the base case, four different scenarios are analyzed. These four modifications are: (1) removing the flotation circuit from the preparation plant and sending all of the fines directly to the clean coal, (2) lowering the quality of coal from one of the mines, (3) applying discounts to the unselected site to improve its competitive position, and (4) adding a new mine. A detailed discussion of the base case and the effect of these four alternatives is presented.

Jan 1, 1983

By A. W. WALKER

All branches of production engineering showed steady and definite progress during 1941. Most of it has been of the slower and more conservative type rather than the sensational. To a large degree the changes have been influenced by the expanding war economy, and this tendency will probably be even more marked during the coming year. The stress of the times is placing more emphasis on the principles of engineering and conservation, with the object of obtaining the greatest possible recovery with a minimum waste or expenditure of equipment. Also available material supplies are often being turned to new uses.

Jan 1, 1942

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

By REED H. HYDE

IN these days of low metal prices and difficult marketing conditions, any treatment that will improve the grade of a product is of interest, particularly when the operation involves little or no addition to the total cost and may even result in a marketable by-product. Such a' combination of circumstances exists, in some cases, in the zinc industry, where it has been found that certain impurities can be removed from .the ore during the Dwight-Lloyd sintering operation, previous to reduction to metal. Consequently it is not surprising that zinc smelters having these sintering machines are paying particular attention to this phase of the operation. Loss of zinc as fume is very low under the conditions obtaining in sintering zinc ores, but impurities such as cadmium and lead are more readily fumed off and it is on this fact that the purification is based. As a result of preferential volatilization of these impurities a sintered product' is made from which purer zinc metal or oxide can be produced, while the fume may be collected and treated to recover the impurity metals. To be effective the operation must be carefully conducted, but no special equipment other than that of a well designed Dwight. Lloyd plant is needed.

Jan 1, 1931

By M. C. Leverett

KNOWLEDGE of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum pro-duction, but is as yet incompletely devel-oped. The object of this paper is to show the application of well established thermody-namic and physical principles to these prob-lems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: I. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion of mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. CAPILLARY EQUILIBRIUM IN SANDS Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treat-ment of problems of mixture flow, the con-cepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis-turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predict-able from the theory of capillary equi-librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, of course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is as-sumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reser-voir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems in-volving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately in-vestigated experimentally. Experimental evaluation of the pertinent properties of natural reservoir rocks will permit the ex-tension of the numerical treatment to prob-lems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids; that is, the manner in which the reservoir fluids are distributed vertically when the forces due to capillarity are just balanced by those due to gravitation.

Jan 1, 1940