Search Documents

By M. A. Childers

Recent work with controlled laboratory tests.' field experience and a new analytical approach indicate that casing centralization, pipe movement and relative rheological properties between the mud and cement (yield point and density) are the three controlling factors in successfu1 primary cementing of dual casing. Turbulent flow has been demonstrated to be unnecessary under the severe displace ment conditions of parallel dual strings of casing. Simultaneous reciprocation of dual casing in directionally drilled boreholes is highly dependent on centralization and on the rapid initiation of pipe movement once the casing has been run to total depth. Successful cementing of 30 out of 32 dual, 3%-in casing wells substantiated these conclusions. A review of 15 dual, 3 1/2-in. casing wells completed prior to the adoption of these principles disclosed only one success. Mathematical and graphical techniques permit the engineer to analyze and anticipate the success or failure of a cementing operation. Standoff, mud displacement and reciprocation can be analyzed mathematically and planned in deep, directional or straight boreholes by review of annular geometry, relative rheological properties between the mud and cement, and forces caused by caring weight, functional drag and differential sticking. Introduction The objective in primary cementing is to displace the drilling fluid with cement that will bond to the formation and casing to prevent communication through the annulus. The predominant cause of failure appears to be channels of gelled mud that remain in the annulus after cementing.1 '* Past investigations have noted many procedures that could improve the displacement process.2-' These procedures include centralization, chemical preflushes, mechanical mud cake removers, controlled flow rates in certain regimes, pipe movement an1 control of mud and cement properties. Not until recently have the effects of many of these procedures been isolated so that their individual importance could be determined. In a recent paper,' a comprehensive and analytical laboratory study of various factors controlling the displacement process concluded that there are three major factors in obtaining complete mud displacement by the cement slurry. 1. Good relative rheological properties between the mud and cement. The cement should be heavier and have a yield point and plastic viscosity higher than the mud being displaced. Buoyancy forces often can dominate the displacement process. 2. High degree of standoff or centralization. The more centered the casing, the greater the likelihood of complete mud displacement and removal. 3. Pipe movement obtained by rotation or reciprocation. Often unfavorable rheological properties between the mud and cement, and poor standoff can be compensated by pipe movement. This work demonstrates the compatibility of the latter concepts with field results extended to the more severe dual casing displacement process. Early Experience With Dual 3'/t-In. Primary Cementing Early slim casing completions in the West Delta Block 73 field, offshore Louisiana, included 17 dual 3%-in., 3 single 3% -in. and 1 dual 2% -in. casing installations. Table I provides data on these earlier wells. Usually, common Class A cement was placed across the pay zone and 12 percent gel cement was placed to a height of 500 ft above the highest productive sand. Centralizers (6%-in. OD maximum expansion) were placed two or three per joint on both casing strings from total depth through the completion intervals and at least one per joint for the remainder of the cement sheath. A number of techniques and procedures were attempted to improve cementing success. Casing was run simultaneously or separately with a number of mud conditioning and circulating techniques. Mechanical aids such as cement bonders, slmiding sleeves, turbulizers and various sizes and strengths of centralizers were used. Common and gel cements were mixed with fresh or sea water with a number of different additives to control retardation and dispersion. Cements were thinned and mixed at high rates to try to induce turbulent flow in the annulus. On one well the "slow flow" method was used." Perforating was accomplished with a jet orienting gun. Unsuccessful cement jobs were indicated by production of extraneous fluids or by pressure communication between zones. On test, five wells flowed water, four flowed sand and six had pressure communication with the other string or the 10%-in. casing. A total of 25 remedial squeeze ce-

Jan 1, 1969

By J. C. Bayles

Jan 1, 1885

By R. W. Powers, M. V. Doyle

ThE solution of a diatomic gas such as 0, or N2 in a metal usually follows Sieverts' law; i. e., Here C is the solute concentration at equilibrium and P, the gas pressure. The proportionality constant Ks is also the equilibrium constant for the reaction 1/2 02 (at pressure, P) - 0 (in solution at [21 concentration., C). to use oxygen as an illustrative gas. Sieverts' law is therefore interpreted to indicate that diatomic gases go into metallic solution atomically and that the solute "gas" atoms interact negligibly with each other. Of course, this interpretation is strictly valid only over the temperature interval in which the reaction indicated in [Z] can be investigated. At temperatures several hundreds of degrees below this interval, the possibility of interactions between solute atoms is conceivable. Indeed, from internal-friction measurements some evidence for the existence of groupings of oxygen atoms in tantalum solid solutions was presented a few years ago.1,2 Over a range of solute concentration, the experimental oxygen internal-friction peak in tantalum, measured as a function of temperature at constant frequency of vibration, can be described as the sum of two elemental peaks, each corresponding to a separate relaxation process. At 0.7 cps, the height of the elemental peak found at 137°C is proportional to the oxygen content, whereas the height of the one at 162°C varies as the square of the oxygen concentration. The 137°C peak was presumed to arise from the stress-induced ordering of oxygen atoms among various classes of octahedral sites in the manner proposed by Snoek.3 The 162°C peak was attributed to a somewhat similar stress-induced ordering process, in which each oxygen atom was interacting with a neighboring oxygen atom. Similarly, the experimental peak due to nitrogen in tantalum can also be described as the sum of two peaks. The height of one varies as the nitrogen concentration and the other as the square of this quantity. In fact, some evidence of solute interactions exist for all oxygen and nitrogen solid solutions of Group V transition metals. However, the interaction energy was not obtained previously for any alloy. The determination of this quantity, as a part of a more intensive study of the interaction between oxygen atoms in solid solution in tantalum, is reported in this paper. PRINCIPLE OF THE EXPERIMENT Consider an equilibrium in a solid solution of tantalum between oxygen atoms which are bound together pairwise and those solute oxygen atoms which are not so associated. 20 (Ta) - O2 (Ta) [3]

Jan 1, 1960

By H. H. Podgurski, J. C. M. Li, Y. T. Chou, F. N. Davis, R. A. Oriani

When an Fe-2 pct A1 alloy is nitrogemted at 500ºC with a gus tnixture (NH3-H2) in which the nitrogen activity has been kept Lou] enough to avoid the formation of iron nitride, a two-phase alloy is generuled which consists of AlN particles and a ferrite phase cotaining a heavy network of dislocations. The amount of nitrogen contained in such an alloy, when equilibrated with the nitrogenating atmosphere, far exceeds both that needed to satisfy the normal solution requirements of a Fe and that needed to convert all of the aluninuwi to AlN. This excess nitrogen is accounted for as being trapped on dislocations, adsorbed at the ferrite -AlN interface, and as an en-Iuznced lattice solubility in strained ferrite. This excessive uptake of nitrogen had previously been attribuled by other investigators to the formation of a nonstoichiornetric aluminum nitride. Isotope exchange experiments revealed various amomts of exchargeable N14 present in the originally nitrided samples that could not be removed by reduction with HS at 500ºC. This exchangeable nitrogen has been identified us that bound to the AlN -ferrite interface. Estimates of inter facial areas in alloys containing -3 pct by weight of A1N are as high as 10 sq m per g of alloy. ThE first1 of this series of papers described the experiments forming the basis for the elucidation of the mechanism of the formation of aluminum nitride particles within an Fe-A1 alloy. It was found that not only are dislocations necessary for the nucleation of the AlN particles but also the nitriding reaction in turn produces a dense network of dislocations in the ferrite matrix. It was also observed that nitrogen in excess of that needed for the formation of stoichiometric AIN is taken up by the alloy without the formation of an iron nitride. The present paper is an analysis of the excess nitrogen sorbed by the nitrided Fe-A1 alloy which considers the structure generated by the formation of the aluminum nitride particles. Because of the high density of dislocations, this system has proved to be quite useful in studying nitrogen-dislocation interactions. Wriedt and Darken2 have already reported such studies in a cold-worked ferritic steel. EXPERIMENTAL Nitrogen Sorption. The specimens of this alloy were cold worked (50 pct reduction) to 0.011 in. thickness and chemically cleaned in a 2:1 concentrated phosphoric acid-50 pct hydrogen peroxide solution before nitrogenation. The flowing nitrogenating atmosphere (11 pct NH3-89 pct H2) was established before the ni- trogenating temperature was reached. The same gravimetric and gas-flow equipment described in an earlier paper1 was also used in this investigation. Changes in nitrogen concentration were followed gravimetrically when establishing the isotherms. In the isotope exchange experiments, concentration changes were followed volumetrically. In some instances chemical analyses (Kjeldahl method) were used to check for material balances in both the gravimetric and volumetric procedures. Our objective was to obtain reversible nitrogen sorption isotherms for alloys equilibrated with NH3-H2 gas mixtures over a large range of nitrogen activity* and temperature. The *Defined as equal to PN H /P3/2 ,where P corresponds to partial pressure in atmospheres. Actually the nitrogen activity, aN, in the alloy equals K PNH3 /p3/2H2, where K is the equilibrium constant for the reaction NH3 = N + 3/2H2. upper limit for nitrogen activity was below that which would produce iron nitride; for reasons which will become apparent later, most of the sorption studies were made in the temperature range between 400" and 500'C. The alloy sample studied most extensively in this investigation was given a series of successive reductions (100 pct H2) and nitrogenating treatments at 500°C to attain a stabilized structure. Presumably some dislocations were lost during these treatments. Throughout most of the sorption studies, temperature was held at ± 1°C and the gas-phase composition was held to k0.2 pet NH3. Based upon the results of numerous diffusion experiments with this alloy* the 'Results to be published in a third paper of this series. times chosen for equilibration were considered more than adequate, Nitrogen Isotope Exchange. The first exchange experiments were carried out by circulating a measured quantity of H2 and NH3* (with a predetermined isotopic *The NH3 was synthesized over a synthetic ammonia iron catalyst using H2, and N2, enriched with N15. AS the NH3 was formed it was removed continuously from the gas phase by circulating the mixture through a refrigerated (78ºK) trap. When most of the nitrogen had been converted to NH3, it was distilled from the trap into a glass storage vessel. composition, N15/N14) over a nitrided specimen at 450°C in a closed glass system. Attempts to reach the exchange limit isothermally, i.e., an isotopic ratio (N15/N14) in the gas phase identical with the extractable nitrogen in the nitrided alloy, were futile. The exchange rate between the gas phase and the alloy was too slow, involving many days. To circumvent the slow exchange with the gas phase, measured amounts of N15 and N14 were introduced into the alloy by nitrogenating with an NH3-H2, mixture at 500°C containing an N15/N14 ratio of 7.76; the charged specimens were then sealed by allowing an oxide film to form over them in air, and in this final condition the specimens were subjected to 500°C in vacuum for various times during which isotope exchange was allowed to proceed within the specimen. It was estab-

Jan 1, 1970

By PAUL AUDIBERT

THE downward trend of metal prices seems to act something like a reagent that precipitates selfishness in most business men's hearts; in the same way the upward trend precipitates altruism. Operators do not say: "I continue working my mine without curtailment because I can afford the present prices while my neighbor cannot and thus will give me way." They say: "I continue working my mine because 1 consider it a service for consumers. They will get better prices on a free market. Any curtail¬ment would be an attempt to raise prices artificially, that is to say, bad economics." Copper producers have learned how fallacious is such an opinion. It perhaps was not fallacious in olden times when all mines were worked on a small scale even if operating on a big deposit. At that time the supply and demand law played fair. When prices were too low and profits were vanishing for many mines, they would. shut at once, then little by little the metal scarcity would induce prices to climb up again; finally these prices would reach the point when it became profitable to again work the closed mines. Re-opening and shutting down mines was then a normal custom. Workers and operators weakly deplored this unstability, but there was nothing effective they could, do about it.

Jan 1, 1931

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the silicides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. MANGANESE AS A SCAVENGER Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

Jan 1, 1928

By A. U. Seybolt

In part 111' of this series it was shown that during the selective oxidation of a 3 1/4 pct Si-Fe alloy in damp hydrogen, only silica, (observed at room temperature) as low cristobalite or low tridy-mite or both, was formed as an oxidation product. In some in- „ stances where the film was fairly thin (probably well under 100A) there was some suggestion of an amorphous form of SiO2. The present investigation of oxidation rate showed that the selective oxidation of silicon-iron can be rather complicated, and apparently impossible to rationalize in an unequivocal manner. In some temperature regions, notably near 800" and 1000°C, the data seem to obey the familiar parabolic rate law. However, at intermediate temperatures complications were noted, some of which are possibly due to the order-disorder reaction in the silicon-iron solid solution. IN an earlier report' it was shown that during the oxidation of 3 1/4 pct Si-Fe alloys in H2O-H2 atmospheres only silica films were formed in the temperature range from 400° to 1000°C in hydrogen nearly saturated with water at room temperatures, or at dew points as low as -45°C. In the work to be reported here, some observations are made on the rate of oxide film formation. As in the earlier investigation, electron diffraction patterns generally showed either low tridymite or low cristobalite or both, except for some very thin films. These sometimes showed diffuse rings, presumably due to a very small crystallite size, or in a few cases, diffuse bands probably caused by an amorphous film. EXPERIMENTAL PROCEDURE Vacuum-melted silicon iron made of high-purity materials was rolled into strips 0.014 in. thick, and cut into samples 1/2 in. wide by 1 in. long. Chemical analysis showed 3.2 pct Si and 0.002 pct C. All samples were surface abraded with 600-grit paper, were solvent cleaned, and then placed in an paper,apparatus containing a "Gulbransen type"2 micro-balance. Here the gain in weight of the samples of about 5 sq cm area could be followed as a function of time during the oxidation caused by the water in atmospheres of various controlled water-hydrogen ratios. The water-hydrogen ratios can most easily be described as varying from a dew point of 0°C (PH2O-p^2 = 6.2 x 10-3 , to K (P j -40°C (PH2O/PH^= 1.3 X 10-* Most of the experiments were conducted at the 0°C dew-point atmosphere because drier atmospheres caused so little gain in weight that the accuracy of measurement was poor. Because of this, only the data obtained at PH2O,/P,,,= 6.2 x X3 will be reported. The temperature range extended from 800" to 1000°C; and most of the oxidation runs lasted for about 24 hr. The reproducibility of any reading was about ± 1 ?, but the sensitivity of the balance was about 0.2 ?. The atmosphere, flowing at 200 cm per-min, was preheated to the furnace temperature before contacting the specimen. While the gas flow caused a measurable lift on the sample, it was ordinarily sufficiently constant so that it was not an appreciable source of error. X-ray and electron diffraction checks of the samples before and after oxidation showed no evidence of preferred orientation, either on the metal samples or on the silica films formed. EXPERIMENTAL RESULTS The data obtained are summarized in Table I, and some are given in detail in Figs. 1 to 4. In the fourth column of Table I, kp refers to the parabolic rate constant in the expression (?/cm2)2 = kpt + c [1] where ? = micrograms gain in weight kp = parabolic rate constant in units r2 /cm4 t = time in minutes c = constant It will be noted that in many cases no value for kp is given; this is because in these instances the data did not obey the parabolic rate law. The silica film thicknesses given in the last columns are values calculated from the weight gain, an average tridy-mite-crystobalite density, and by assuming a perfectly plane surface. Fig. 1 shows the data plotted in the form of Eq. [I], hence a linear plot indicates parabolic behavior. It has been frequently observed in the literature that

Jan 1, 1960

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith' and of A. G. H. Andersen .2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford," using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,1,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates h in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,12, 7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 3 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

By A. G. H. Anderson, A. W. Kingsbury

Silicon bronzes containing ken are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 etermined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at iioo°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West? have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,l,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. Preparation of Samples Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 1/8 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1943

By A. G. H. Anderson, A. W. Kingsbury

Silicon bronzes containing ken are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 etermined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at iioo°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West? have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,l,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. Preparation of Samples Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 1/8 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1943

By C. A. WARNER

IN all the meetings of the Petroleum Division, emphasis was placed on the essential importance, in the successful furtherance of our war effort, of efficiently producing, transporting, refining, and utilizing maximum quantities of crude oil and natural gas with the minimum expenditure of critical material. With representatives present from all branches of the petroleum industry, from all parts of the United States, the sessions were opened Tuesday morning with Commander Harry P. Stolz. U.S.N.R., Chairman of the Division, and A L. Haider as associate chairmen. From that time until the symposium on petroleum economics was closed Thursday afternoon papers of exceptional interest and importance were presented and discussed in a most frank and open manner.

Jan 1, 1943

By P. A. Laxen, H. R. Spedden, A. M. Gaudin

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface1 are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.2,3 Study of the adsorption of sodium from an aqueous solution on quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained.4,5 Three main factors which appeared likely to affect the adsorption of sodium are: 1-concentration of sodium in the solution, 2-concentration of other cations in the solution, and 3-anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in the amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxylion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory4 except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying5 To minimize the laborious preparation of quartz, experiments were made to determine whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na' activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot II) and 2000 (lot III) as determined by the Bloecher method.6 Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.7 It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß radiation and a 1.30 mev ? radiation. The decay scheme is illustrated in the following equation: [Y Nam S. - 'Net 3 years] The ß radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang8 The original active material was 1 ml of solution containing 1 millicurie of Na22 as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen5 In brief, it included the following steps: 1-Ascertainment of linearity between concentration of Na22 and activity measured. 2-Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3-Taking precautions to avoid evaporation of water during centrifuging.

Jan 1, 1952

By J. Cervik, P. C. Thakur, S. D. Lauer

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh coal seam in northern West Virginia under USBM Cooperative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of 14 small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by a surface exhaust fan. The methane capture ratio was poor at 7% to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance, the boreholes should be drilled from a point 30 to 45 m (98 to 148 ft) from longwall pillar over the largest chain pillar. The standpipe should be grouted for at least 6 m (20 ft), and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane migration toward cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45º ± 10º.

Jan 1, 1986

By Henry Morris

AS STATED last year, in a similar review by David White and the author, any review of the petroleum industry purporting to cover such a wide field can only mention the principal facts. This incompleteness is necessitated not only by the limitations of space, but by the delay in receiving detailed information. The principal feature of the year, in Europe, was a material increase in the consumption of petroleum products, and a notable decline in prices. Although there we relative increases in production in Roumania and Poland, the total did not by any means keep pace with the increase in consumption, which, as usual, was supplied "from America and both the Near and Far East. The interest in Asiatic production, as usual, centers around the Persian fields, which, according to the annual report of the Anglo-Persian Oil Co. published at the close of last year, it was estimated would amount to 3,775,000 tons by the close of the fiscal year, March 1, 1924. Russia also showed an increase in production. In Africa there was nothing of outstanding interest in production, although Egypt showed a decrease and the goverment refinery at Port Said was closed.

Jan 3, 1924

By George A. Jr. Dornin

A TRULY sound ingot can be made only from steel that is completely deoxidized. Given this condition, there is one further basic requirement-the steel in the ingot must solidify progressively from the bottom to the top. Any method of making the ingot that produces this type of solidification will yield sound products. Since a big-end-down ingot will not satisfy this condition, all sound steel today is produced in big-end-up ingots, the standard tool being the big-end-up mold fitted with some sort of refractory hot top. No one uses hot tops from choice, be cause of the bother and expense involved and because of the low yield resulting from their use-they are used because there has been no alternative where sound steel was required.

Jan 1, 1947

By William B. Plank

THE growing dependence of our vast industrial civilization (:n mineral products demands today, as never before, the highest technical skill in those who produce these product-;. That the duty of training the engineers, whose responsibility it is to produce these mineral products efficiently and in sufficient amount, falls directly on the schools of mining is beginning to be more fully recognized. The Institute, realizing this fact and that its future membership depends largely on the annual accretion of young men, is showing a keen interest in the problems of the mining schools and in the work of its Committee on Engineering Education. The Committee has, during the past several years, considered the problems connected with the training of men for the mineral industry, whether these have been problems of college training, or placement of the young engineer in the industry, or personnel training after he enters the industry. The field of interest and discussion has been as broad and varied as the mineral industry itself. Coal mining, metal mining and metallurgy have been discussed and the papers on these subjects have been outstanding contributions to the literature on mineral education.

Jan 1, 1931

By Arthur Taggart

SOME years ago, A. M. Gaudin and one of the authors published a paper showing removal of tar acids from solution by sulfides preferentially as compared to gangues (specifically by galena as compared to quartz).1 The underlying phenomenon was classed as adsorption, and the paper went on to develop the general thesis that so far as water-soluble frothing and collecting agents in flotation are concerned, the phenomenon of adsorption is one of controlling importance. Adsorption was defined in that paper as "a process of rearrangement of a system, which results in establishing a difference in concentration, as between the interfacial layers and the bulk of the phases, of a substance or substances initially uniformly dispersed in one or several of the phases." The paper went on to develop the relation between adsorption and surface energy according to Gibbs' equation (which may be thrown into the form U/c = KdT/dc, where U = excess concentration in surface layer, c = concentration, T = surface tension, and K is a constant), and pointed out that, according to this equation, degree of adsorption and change in surface tension vary directly. The present paper offers a somewhat different definition for the term adsorption; and sets up, in sweeping terms, the generalization that simple chemical reaction underlies the functioning of the flotation reagents which control mineral collection, when these reagents are soluble in and act from solution in the water of the pulp.

Jan 1, 1930

By John McCaslin

ONE of the most common technical terms in the U. S. today is automation-a word not listed in the 1946 dictionary. The influence of automation on the national economy has been tremendous. It has even been the subject of congressional investigations. Automation, writes Aronson, substitutes mechanical, hydraulic, pneumatic, electric, and electronic devices for human effort and decision? Automatic devices and instruments are used extensively in some industries, but many others have yet to take full advantage of these great discoveries. The petroleum industry has been a leader in using automatic controls-some refineries are almost completely controlled by automatic devices. The field of geophysics is entirely dependent on instruments and has progressed at almost exactly the same rate as improvements in instrumentation. In metallurgy and mineral dressing use of instrumentation is increasing very rapidly. Mining engineers throughout the country are beginning to think in terms of instruments and controls.

Jan 3, 1958

By E. C. Weichel

THERE have been many attempts at permanent roof support in anthracite mines, in some cases brick arches, in others concrete, and also combinations of brick or concrete walls with steel beams. These supposedly permanent roof supports have frequently failed when heavy pressure is brought to bear upon the structure, because they are so rigid that failure occurs because the structure is unable to adjust itself to the increased load. Roof pressure exerts a tremendous weight, and it is at times difficult to find any means of support which is strong enough to bear the entire pressure, unless this supporting structure has in itself the element of some flexibility which will enable the structure to hold the moving mass until it "arches" itself. If the supporting medium has flexibility enough so that it can adjust itself to the heavy initial loads, and so give the overlying material an opportunity to form a self-supporting arch, then such a roof support will be more useful than any rigid roof support. There has recently been introduced into the anthracite region a new form of gangway lining that is flexible enough to slightly adjust itself under heavy pressures, and so give the loosened material which is being supported a chance to form into an "arched" mass. This lining, manufactured under patents granted to Hans Schaefer of Essen, Germany, was introduced in the United States in the summer of 1928, at which time the Amercan licensee, Richard Howells of

Jan 1, 1930