Search Documents

By Nathaniel Arbiter

INTRODUCTION Almost seventy-five years ago problems in the recovery of sulfides from then designated slime fractions were the impetus for the development of flotation. The fall-off in recovery by gravity methods below about 200-mesh, and the shift from coarser vein deposits to more disseminated ores, particularly for copper, provided the background for flotation's rapid advances. Although the ensuing years have witnessed major improvments both in flotation reagents and in flotation machines, many problems are still with us. And since, with the exception of the unique leaching of chalcocite ores at Inspiration, flotation is still the exclusive mainstay for primary recovery of all base metal sulfides, the solution of these problems as they arise is vital to the well-being of the mining industry. Before considering the problems themselves, it will be useful to review the current status of sulfide flotation in the United States. The last comprehensive survey by the Bureau of Mines in 1975 (1) showed sulfide ore tonnages treated from 1960 to 1975 as summarized in Table 1; Table 2 gives similar data for the flotation of all non-sulfide ores. Noteworthy is the leveling off in sulfide ore tonnages in 1970-1975, with a probable further decline in the past three years, and the sharp drop in the number of plants floating sulfide ores. In contrast, the tonnages of non-sulfide ores floated, as well as the number of individual plants, has continued to increase. In spite of these trends, two-thirds of the total tonnage of the ores to which flotation is applied is still represented by sulfides. Average grades of sulfide ores in 1975 were: about 0.6 percent for copper; near 5 percent for lead; and near 3 percent for zinc. Recoveries averaged in the low 80's for copper; about 95 percent for

Jan 1, 1979

By H. A. Schlesinger

Various studies have estimated that for the next few decades, about half of all new power plants will be nuclear. The other half will be fueled with coal. Pending legislation on air pollution control would require all new coal-fueled power plants to install stack gas scrubbers or other technology to reduce sulfur oxide (SO,) emissions. These regulations would require flue gas desulfurization (FGD) or other technology for SO, reduction even on lower sulfur western coals. Among the options for FGD are single or dual alkali throw away processes using lime or limestone as the major reagent. These processes are currently more economically attractive than recovery processes, such as magnesium oxide and Wellman- Lord, that produce a salable product such as sulfur or sulfuric acid. One of the major problem areas with the throw away processes is disposal of the thrown away solid wastes, primarily calcium sulfite (CaSO3) and calcium sulfate (CaS04). Coal ash also must be disposed of, even if SOx reduction is not required. This paper addresses the alternatives for handling and disposal of throw away lime, limestone, and dual alkali process solid wastes. Advantages, disadvantages, and the economics of various methods are discussed. Both large central station power plants (500-1000 MW capacity) and smaller industrial power plants (up to 100 MW capacity) are considered. High sulfur eastern coals (53% S) and lower sulfur (3 1% S) western coals are considered.

Jan 1, 1981

By B. K. Miller, George E. Moore

THE Missouri fire clays are here divided into plastic and semiplastic clays occurring as widespread bedded deposits in east central Missouri and flint and diaspore clays occurring as isolated "sink-hole" deposits in the north central Ozark region. Visual inspection was the first method used in clay prospecting. Thin overburden, hard sandstone "rimrocks," and the occurrence of diaspore float made this method particularly applicable in the flint and diaspore fields. The first drilling tool used was a hand auger. One man can drill 25 to 50 ft. per day at a cost of about 35 cents per foot. Holes can be drilled to a depth of 150 feet. Spud drills are often used where the over burden is hard. This drill uses a slotted earth socket bit. A two-man crew can drill about 100 ft. per day at a cost of about 35 cents per foot. Mechanically powered auger drills have been used extensively in wildcat drilling in the past few years. This type of drill furnishes a continuous set of cuttings. The practical depth limit with this drill is 50 to 60 ft. Two men can drill 300 ft. per day at a cost of about 20 cents per foot. Core drilling is used mainly to prove a known clay deposit. A two-man crew with a No. 22 Sullivan drill can drill about 30 to 40 ft. per day in soft clay, at a cost of about $1.25 per foot.

Jan 1, 1947

By M. Tanaka, S. Kita, Y. Jinnouchi, Y. Sawada

This paper generalizes the results of the recent theoretical and experimental investigations on the air-pulsated jigs in Japan. The pulsating mechanism is analyzed as a special vibratory system, and the jigging mechanism as a mass system subjected to the law of hindered settling. The results of investigations on the following items are reviewed: dynamics of the pulsating mechanism; pulsation in a practical TACUB jig development of a new type of air valve; uniform pulsation in a large Baum jig; motion and mobility of bed particles; separating speed in hindered conditions; and standard deviation in practical jigs.

Jan 1, 1985

By John J. Reed

The mines of southeast Missouri's Lead Belt have been in operation since 1864, almost 100 years. During this period about 10 pct of the total ore available has been left in place as pillars, and this now represents the best ore reserve left to the older mines. St. Joseph Lead Co. has been investigating various plans of pillar recovery for several years. The example to be described is only one possible approach under a specific set of conditions. Conditions vary greatly in the different areas within the Lead Belt, and the same approach would be entirely in- adequate in certain other areas, but there are important sections where this system is clearly applicable.

Jan 7, 1959

By H. R. Fife

AN extended study of dustproofing Freeport-seam coal has empha-sized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption proper-ties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measure-ments on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average ton of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by sur-face area. Wax extraction data on 1-in. to 0 slack from mine-run treated Free-port-seam coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness.

Jan 1, 1937

By R. P. Rothwell

AT this our first meeting I beg to call the attention of the members of our Institute to what is certainly a question of the greatest possible importance to the industries we represent; and more particularly to the welfare of the coal and iron trades : I refer to the enormous waste of coal in mining and in its preparation for market, as now practised in our anthracite coal-fields. It is a fact which many of you can certify to, that we are wasting fully one-ha f of all the coal in the veins we are now working, and there are cases, which might be mentioned where this proportion, immense as it is, has been greatly exceeded. The popular belief that our deposits of anthracite coal are "practically inexhaustible," is very far from being founded on facts. On the contrary, supposing the present rate of increase in the production to be maintained, it is probable that a maximum yield for our coal-fields would be attained in about fifteen years ; there are in fact some of our smaller basins where the principal veins are nearly exhausted and the production has already attained its maximum. There are others, again, where the depth attained-and it must be borne in mind that we commenced working at the surface outcrop-moderate though it is (scarcely ever reaching eight hundred feet), has so increased the cost of mining as to imperil the capital invested, and though it requires but little foresight to predict the time when the difficulties of mining will be very considerably increased by reason of the greater depth, greater quantity of water, fire-damp, and other fruitful sources of cost, yet, ignoring these recognized facts, we continue to waste more than one-half of the coal where it is obtained with the least danger, expense, and trouble, that is, near the surface-either above water-level or at a moderate depth below it. The inspection of almost any accurate mine map will satisfy you that, on an average, we leave fully one-third. of the coal in the ground as pillars to support the roof; in some places more than one-third thus remains, while it is very rare that less than one-quarter is left. In almost every case this coal is absolutely lost, for it will very rarely pay to reopen gangways and lay roads to it after that portion of the mine has been abandoned. Is it necessary in all cases to support the roof, and where it is, may not some artificial

Jan 1, 1873

All data about shipments from the present state of West Virginia, even when it was still a part of the "Old Dominion," are shown in Table 56 together with the source of information, and all other figures are estimated. While the earliest production was undoubtedly in the extreme northern part of the state, coal having been quite largely used in Pennsylvania before any is credited to West Virginia, the largest production in the early days of the industry was along the Kanawha River where the salt furnaces used tremendous quantities for years before shipments were made by river. When we take into consideration the economic conditions existing then, it is evident that the consumption of coal by the salt industry along the Kanawha and Kiskiminitas Rivers rivalled in importance that of any industry today. There were no canals built in this state, the shipments before railroads were built being by the Ohio and Kanawha Rivers, and production in the northern counties began after the Baltimore & Ohio Railroad was completed from Cumberland to Wheeling. For some years after this line was completed all locomotive fuel used on it was hauled from the Cumberland region. The movement of coal from Boone County by Coal River to the Kanawha and Ohio Rivers from 1857 to 1880 is rather unique in its size and the length of movement, nearly all the coal going at least as far as Cincinnati and much of it to New Orleans. Fayette County began shipping when the Chesapeake & Ohio Railroad was completed and Mercer County, when the Norfolk & Western Railroad reached there in 1884; none of the other large producing counties in the southern part of the state began producing coal in the period under study.

Jan 1, 1942

B. F. TILLSON,* Franklin Furnace, N. J.-I would like to ask Major Yerkes if he will not give us more examples of the tests than are contained in the printed pamphlet. It would be of great interest to study them more carefully. ROBERT M. YERKES, Washington, D. C.-The reason for not reproducing the methods in any public print is that it lessens their value and necessitates the preparation of new test materials. BRADLEY STOUGHTON, New York, N. Y.-I hope that this matter will be of so much interest to the members of the Institute that the Directors will decide to appoint a committee which can bring further results of this practice before us. I understand that Columbia University, at least in some departments, has already adopted the B and A tests and is using them. I understand that some industries have considered seriously the question of grading their employees in accordance with

Jan 4, 1919

By Eric J. Bradshaw

For several hundred years the petroleum industry has flourished in Burma and at the close of the eighteenth century there were over five hundred producing wells in the Yenangyaung field. These were laboriously dug by hand and were exceedingly primitive, yet even today a small part of India's total production is obtained from hand-dug wells. The Indian Empire, the cradle of the oil industry, today produces but an unimpressive fraction of the world's supply of petroleum, not because the size of her contribution has diminished, but because it has remained more or less stationary while other countries have far outstripped her during the prodigious increase in the world's production of petroleum in recent years. Though for the past 10 years the total production in India has been remarkably constant, it has become increasingly difficult to maintain this output and at any rate from the older fields a slow decline may be anticipated unless new productive horizons are discovered. Production figures for the 10 years 192&1929 (the last year for which figures are available) are given by fields in Table 1. Crudes of Burma and Assam The bulk of India's production comes from the Yenangyaung and Singu fields, from which the crudes are very similar, the only important difference being that the oil from the Singu-Yenangyat structure contains a higher percentage of lighter fractions. The Burma crudes resemble that of the Panhandle of Texas and have a high content of solid paraffin, though strictly speaking the oil is of mixed base with a low content of asphaltum. With the exception of the negligible production from Sabe, the Burma crudes do not require dehydration; the sulfur content is very low and is innocuous. A small amount of naphthenic acids occurs in the kerosene and intermediate oil fractions while the lubricating fraction is practically free from acid. The ash content is low and the average A.P.I. gravity of mixtures of Yenangyaung and Singu oil is 36.4. Burma crudes require only light refinery treatment and practically dl the fractions are merchantable. Part of the gasoline supply is stripped

Jan 1, 1931

By Alfred H. Bell

Drilling activity in the eastern interior coal basin, which includes Illinois, southwestern Indiana and western Kentucky, decreased greatly in 1931. Only 521 wells were drilled as compared with 1438 in 1930.' The decline in oil production (Fig. 1) was due partly to the failure of new production to make up for the natural decline of the old wells and partly to artificial curtailment of production to meet a decreased demand. During the year prices trended sharply downward until July, after which they made a partial recovery (Fig. 2). The average price of Illinois crude, which is the same as that for southwestern Indiana, was $0.852 per barrel in 1931 as compared with $1.616 in 1930, or slightly more than one-half. The cost of drilling has declined only slightly. The 25 per cent curtailment of production which was adopted by agreement of the southeastern Illinois operators on Sept. 1, 1930, ended on June 3, 1931. It was effective for five months in 1931 as compared with four months in 1930. The outlook for 1932 is for drilling activity in the whole area to continue at about the same rate or to decrease somewhat unless it is stimulated by a substantial rise in crude oil prices or by the discovery of extensive new productive territory. Discoveries of new productive areas and new sands during the year were few. A new gas area was discovered early in the year in Busseron township, Knox County, Indiana, in which the producing sand is in the Pennsylvanian at depths of 630 to 730 ft. The wells had a total initial open-flow capacity of 7 or 8 million cubic feet per day but are shut in for lack of marketing facilities. An exceptionally large gas well which was drilled in Gibson County between Oakland City and Francisco reached a total depth of 1490 ft. and produced from the Brown sand of Chester age. The initial open-flow capacity was reported as 13 million cubic feet per day. In western Kentucky a number of extensions to oil and gas-producing areas are reported. The most active drilling campaign was in Hart County, where 124 wells were drilled, most of them in the

Jan 1, 1932

By John H. Melvin

THE Omaha District, Corps of Engineers, has been doing subsurface exploration work for a number of years, both by contract and with its own forces. Certain practices and procedures concerning the recovery of large diameter cores have been developed which will be described in this paper. GEOLOGY Most of the drilling to date has been in connection with structures on the main stem of the Missouri River above Sioux City, Iowa. A wide variety of subsurface conditions has been encountered. The bedrock formations appear in regular order from the oldest to the youngest, traveling upstream; or in other words, the general regional dip is to the northwest. The oldest formation is the Carlile shale, a compaction or noncemented waxy shale of Cretaceous age. Because of its uncemented, soft nature this shale has a tendency to grind or wash away when drilled. It also has a tendency to rebound or expand when the overlying pressures are removed. A 25-ft bed of sharp, friable sandstone called the Codell member is present near the top of the Carlile shale. This member is a cemented sediment, but in drilling, many of the sand grains are broken loose and exert extensive abrasive action on the core barrel and bit. Above the Carlile shale is the Niobrara chalk, a soft calcareous deposit with shaly horizons and some thin beds of bentonitic clay. The average thickness of this deposit is about 145 ft. It is soft enough to be sawed or bored with ordinary woodworking tools, yet is compact enough to be used as building block. The Pierre shale, the formation above the Niobrara chalk, is over 800 ft in thickness and is the most widespread material in the area. It is a dark colored, compaction shale containing numerous thin bentonitic clay seams and at certain horizons, hard manganese concretions. The shale has numerous faults and in addition, along the valley walls, has undergone considerable - slumping. Joints, fault planes and slickensided surfaces are common features encountered in drilling and add to the difficulties of high core recovery. East of the Missouri River the bedrock is generally covered with from 100 to 200 ft of glacial till, composed of clays, silts, sands, gravels and boulders. The valley itself is filled with alluvial deposits, mostly of the sand and gravel sizes, and contains a buried preglacial or interglacial channel over 100 ft in depth. The overburden deposits require sampling in connection with engineering studies and must also be cased before the underlying bedrock can be cored. The diameter of the required overburden samples can thus have an indirect effect on the size of core recovered from the bedrock. West of the river, which in most cases is the western boundary of glaciation,

Jan 1, 1947

By R. J. Sherman, M. R. Achter

IT has often been reported that coatings may strengthen single crystals and polycrystalline specimens of coarse grain size. This note reports the effect of a surface layer of fine grains on the creep-rupture properties of coarse grained nickel 99.8 pct pure. Sheet specimens were machined from cold-rolled material, finished by surface grinding and annealed at 1230°C in vacuum for 4 hr. Half of them were re-ground on faces and sides and annealed at 925"C for 1 1/4 hr. The double grind-anneal treatment produced a structure consisting of a surface layer of fine grains of 0.02 mm diam on a coarse-grained substrate of grains of 0.40 mm diam. Comparison with specimens which received only the single grind showed that the second grind-anneal did not alter the structure of the substrate. Several modifications were made in specimen design to eliminate erratic rupture behavior outside of the gage length. In the final design the gage section, oriented parallel to the rolling direction, was 1.00 in. long, 0.4 in. wide, and 0.0625 in. thick. End tabs were pinned in place. Although other configurations (welded end tabs, transverse orientation, and wider gage section) showed similar effects of a layer of fine grains, because of the erratic rupture behavior, only the data from the final design are reported here. Creep tests were performed at 650°C in air and in a vacuum of 10~5 mm Hg. Creep rates were measured from the movements of the lever arm. Since the broken sheet specimens could not be fitted together, elongations at fracture measured by means of gage marks, do not include the necked portions adjacent to the fracture. Results of the creep tests with and without the fine grained surface are given in Table I. An explanation for the lower strength in air than in vacuum has been proposed previously in terms of the reduction of crack propagation energy by gas adsorption.l In both environments the fine-grained layer produced a small decrease in minimum creep rate and, except for the shortest test in air, a substantial increase in rupture life. The elongation values at rupture, as they are measured here, do not demonstrate an appreciable effect of the grain structure but do show much smaller ductilities in air than in vacuum. Greater elongations maybe associated with the finegrained layer, however, especially in vacuum, in creep curves such as those in Fig. 1. Duplicate tests were not run to determine the re-producibility of the data. It is felt, however, that, in view of the consistent behavior, the prolongation of rupture life may be attributed to the effect of the fine-grained surface. In the data not reported be-

Jan 1, 1962

By Dr. O’Neil Thomas J., Donald W. Gentry

"October. This is one of the peculiarly dangerous months to speculate in stocks. The others are July, January, September, April, November, May, March, June, December, August and February." -Mark Twain Although the preceding chapters describe the type of preliminary evaluation frequently performed in the mining industry, it has been assumed that input data are known with certainty-clearly an enormous simplification. In reality, estimates of ore grade, mining cost, metal price, etc., are subject to varying degrees of uncertainty due to the inability to predict the future with much precision. Management would probably not, for example, be equally attracted to two projects each offering a 20% DCFROI-one for a new gold venture in Nevada and the other for an undersea manganese nodule operation in the Pacific. The high risk with the latter investment tells the obvious; there is more to investment decision-making than a deterministic analysis using "best estimates" of input parameters. The science of decision theory normally distinguishes between decisions under uncertainty, where probabilities of various outcomes are unknown; and decisions under risk, where such probabilities can be estimated. The first case is rarely en- countered in practical capital investment analysis in mining, so the remainder of this chapter focuses on that class of problems where rational probability distributions for the future states of input variables can be estimated. RISK IN MINING Risk in the context of this chapter is the unforeseen deviation of individual cash flows from expected values for a capital project. For a mining venture, the source of this uncertainty could be any number of factors relating to such items as ore grade, ore reserve tonnage, operating costs, product prices, etc. With conventional *Adapted from O'Neil, T.J., 1979, "Procedures for the Preliminary Financial Evaluation of Metal Mining Ventures," Computer Methods for the 80s, A. Weiss, ed., AIME, New York, pp. 556-573.

Jan 1, 1984

By P. E. Baker

Approximate solutions are presented for the heat-flow equations in a loss-free linear system with a moving source and with heat transfer by convection and conduction, representing in situ combustion in an oil reservoir. The rate of heat generation and the velocity vf of the source (flame front) are assumed constant. A cold front or convection front caused by the cooling effect of in-jected air develops behind the flame front and moves with velocity vc, which is determined by the thermal properties of the air and rock. Because of thermal conduction the fronts are not sharp; i.e., they do not represent temperature discontinuities. The following solutions apply after a sufficiently long time. where Q is heat generated per unit volume of formation, k is thermal conductivity, CF is volumetric heat capacity, a is thermal diffusivity, and subscripts 1 and 2 refer to values behind and ahead of the flame front, respectively. The parameter CF2 is contained in v . Te is initial reservoir temper- . C2 e ature and air-injection temperature. Other mathematically possible solutions are presented. The different solutions result from the use of different values for various physical parameters. The solution just presented is thought to be most commonly applicable. INTRODUCTION In this paper, approximate analytical expressions are derived for the temperature profile developed in the underground combustion method of oil recovery. A qualitative description of the process may be found in a paper by Tadema.1 The flame front is regarded as a moving source with a constant rate of heat generation. Heat transfer is by conduction and convection. Previous publications, of which a few are cited here, 2-5 have also attacked this problem and have presented solutions pertaining to different methods of approximating or idealizing the process studied. The present paper also treats an idealized case: linear flow is assumed for heat and fluids, and vaporization and condensation effects are neglected. The results obtained are similar to those derived by Bailey and Larkin,3 but are obtained by an entirely different procedure. The method used here should give considerably greater insight into the physics of the in situ combustion process. Four types of cases are considered, distinguished by thermal and fluid-flow properties of the system. A constant rate of heat generation and constant rate of flame-front advance are assumed. Flame-front temperature is determined for each case using a heat balance which involves the entire temperature profile. The applicability of the different solutions to real systems is discussed after they are all presented. Again, this is done for the purpose of understanding better the physics of the process. Consideration of the nonapplicable solutions and of the reasons for their not applying is significant. In a paper by Cooperman,4 the only case solved is one considered here as not applicable. Fluid flow, as such (pressures, saturations, oil recovery, etc.), is not treated. This subject has been covered in a paper by Wilson, et al.6 Also, we are not concerned with requirements for continuance of the process; we only attempt to determine the temperature history for cases where the process has continued for some time. PHYSICAL SYSTEM AND APPROACH TO PROBLEM A linear flow (heat and fluid) system is assumed and the x-axis is taken parallel to the flow direction. The combustion zone (flame front) is vertical,

By James Douglas

Though liberality is not supposed to be a prominent trait of the Scottish character, Canada owes to a Scotchman, Sir Wm. Macdonald, more than to any other of its people, not only wise ideas, but pecuniary help towards extending education: and another Scotchman, in New York, has sumptuously housed under one roof three branches of the engineering fraternity, of which we are one. Having thus created us members of the same family—for the metaphorical meaning of house and kinship is identical—Mr. Carnegie expresses more emphatically than even he could in words, that, by aff'ording facilities for closest intercourse, he invites the mechanical, electrical and mining engineers to participate in the freest interchange of idea and experience, and to correlate and combine the results of their studies and activities; and, being members of the same household, to banish reserve and secrecy. And now we, the members of the American Institute of Mining Engineers, meet as though we were at home in a neighboring country. For whether we meet in Canada, in England, or elsewhere, the Institute is always received as though no political or geographical divisions separated its members from those of congenial associations in the land of its host. In truth, the title which we have assumed claims for the sphere of our activities the whole American continent, regardless of such trifling details as boundary-lines. The fact that we meet to communicate each other's experience, to discuss our difficulties, and to seek each other's aid in solving the intricate problems that so often present themselves in the course of our professional life, is an acknowledgment of our individual helplessness; and therefore an argument for united effort. But no effort can be of any value if there is an underlying suspicion

Jan 1, 1908

For the US coal industry, 1978 was a nightmarish recurrence of 1977 as the United Mine Workers strike cut into production during the first three months of 1978, followed by the strike against the Norfolk and Western Railway during the summer and early autumn. Coking coal production was floored by the one-two punch of environmental constraints on US coke ovens and competition from low-cost, high-quality imports. At the same time, US ex orts of coal fell to their lowest level since 1962. And in the face of all of this, steam coal consumption was sluggish as utilities burned huge amounts of oil to conserve coal stockpiles during the UMW strike. This was followed by decreased electrical demands due to mild summer weather in many parts of the country and dramatically improved availability of hydroelectric power.

Jan 5, 1979

By D. S. Choi, R. Stefanko

There are a number of complex factors that influence the effectiveness of anchorage to maintain tension in rock bolts. However, a plastic analysis of the anchorage site employing certain simplifying assumptions with application of the Mohr-Coulomb criterion appears to explain the observed phenomena. Such an analysis has been made and a correlation sought with field and laboratory tests. Field tests were made in an anthracite mine in eastern Pennsylvania and included pull tests and long-term tests of a variety of anchorage devices in two basic lengths, 30 and 42 in. in two widely differing seams. Performance is reviewed for wedge, expansion shell, and resin anchorage. Laboratory tests duplicated many of the field conditions but in addition compared the performance of shells with normal and reversed serrations. This performance was compared with the predicted results from the plastic analysis. One of the major problems in conducting long-term underground tests is the selection of suitable instrumentation. All installed bolts were fitted with spherical and hardened washers to insure the best possible torque wrench readings. In addition, commercially available load cells were used. Finally, the performance of a specially developed strain-gage-equipped ring cell is viewed. Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, there has been a lag in development of suitable instrumentation that is simple to install and read out, sensitive, durable, reliable, safe, and economical in evaluating the effectiveness of a bolt over long periods of time. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At The Pennsylvania State University in the Dept. of Mining, research has been conducted for a number of years to measure bleed off in carefully controlled laboratory experiments as well as in underground investigations."-' Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be con- ducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised. Bolts are being used for a greater variety of purposes in mining. Suspending wire sideframe belt conveyors from roof bolts is a common application. The suspension of a monorail transportation system presents yet another. One such system has just been installed in a recently reopened anthracite mine and is presently being evaluated under production conditions. Preliminary studies revealed that a considerable cost reduction was possible by suspending the monorail on bolts anchored in the top. The monorail was to be installed under two widely differing conditions—a competent sandstone above the Buck Mountain seam and a softer shale top above the Skidmore. The type of anchorage device, length of bolt, and long-term performance, consistent with economy and safety, had to be established for the installation once the decision was made to suspend the system on rock bolts. This paper describes some of the testing procedures leading to a final selection. Theoretical Analysis of Expansion Shell Anchorage A detailed look at an expansion shell assembly might shed some light on the factors involved in the design of a suitable shell, Fig. 1. When a bolt is rotated, the tapered plug is forced downward, expanding the leaves laterally to grip the sides of the hole. Two friction surfaces are present: (1) the interface of the plug and leaf and (2) the interface between leaf and rock. The relationships of these friction planes, geometry of expansion shell, and properties of the rock are important in the design of an expansion shell. Therefore, an analysis assuming the rock to behave as a rigid plastic material with its yield governed by the Mohr-Coulomb criterion was made." Furthermore, the effect of friction between the leaf and rock produced by serrations was analyzed.

Jan 1, 1971

By J. King Hoyt

IN both Sweden and England rapid progress is being made in metallurgical development, and the steel industry in both countries is distinctly on the mend. There has been some industrial trouble in Sweden in the iron mines and the wood pulp mills, but at the same time all the steel works have a sufficient stock of pig iron and ore to continue their operations for many months to come. Consequently the strike, unless long protracted, will not affect the output of steel in Sweden. Several of the steel manufacturers in Sweden, most notably Forsbacka and Sandviken, have been very suc-cessful recently in securing large orders, particularly from the continent, for ball-bearing steel, both hollow and solid. Whereas some years ago they ran into-se-rious competition with the German mills, the quality of the steel from these Swedish mills is such that they are now firmly established, and are selling some of the lead-ing manufacturers of bearings on the Continent, as well as automobile manufacturers. The secret of their success seems to lie in a better selection of ores, in more careful control of blast-fur-nace operations and better equipment. Rule of thumb in steel making is taboo, and strict reliance is placed on the laboratory. They are constantly experimenting, and metallurgists and chemists are sent to different countries for study and investigation. In their native ores they have, of course, a unique advantage in pos-sessing iron ores extraordinarily free from phosphorus. At Forsbacka, they are not content with the ordinary chemical analysis of the ingot; but also test the physical properties, as well as make metallographic investiga-tions for slag inclusions, segregations and oxides. In both England and Sweden they watch the nitrogen con-tent of the steel very carefully, a feature which does not appear in the ordinary analysis. In testing carbon, they do not use the color test, but employ an electric .induction device.

Jan 7, 1928

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947