Search Documents

By W. A. Ver Wiebe

It is becoming increasingly apparent that the State of Kansas contains one of the largest reserve areas for oil exploration in the United States. During the year 1936 no less than 54 new oil pools were discovered by drilling. In addition, seven gas pools were found, which may develop into oil pools when deeper horizons are tested. Several old pools increased their reserves when production was found in lower strata. The data presented in Table 2 indicate that nearly 2000 wells were drilled in the state during 1936. Of these more than 1214 found commercial quantities of oil and at least 61 found marketable quantities of gas. The data are conservative because complete results on drilling are not available for the eastern part of the state. Ellis, Rice and Russell Counties share honors with a total of 10 new pools in each. Barton County is prominent with six pools; while those counties claiming fewer new pools are Clark, Ellsworth, Harvey, McPherson, Ness, Pawnee, Rooks, Stafford and Trego. Important additions to our gas reserves were found in Finney and Haskell Counties, which are north of the extensive Hugoton gas area and may some day be part of it. At the close of the year there were 17,317 wells in the state rating as producers. By far the larger share (14,000) were classed as strippers and allowed to flow 100 per cent of their potential capacity, thus accounting for 33,500 bbl. a day. The remaining wells, capable of producing from 15 up to over 6000 bbl. per day, were limited in output according to these amounts. The largest wells having a potential of from 3000 to 7000 were allowed to flow from 2 to 3½ per cent of their official potential capacity. The percentage rises until wells of 15 to 20-bbl. capacity have a rating of slightly over 83. On the basis of these calculations the total potential capacity of all wells was 1,667,814 bbl., and the daily amount allowed was 175,851. Nine of the pools most recently opened were still unable to market their oil and were classified as "shut-in" pools. Total production for the state for 1936 was somewhat over 58 million barrels. Striking Geological Data Some interesting geological data were uncovered by deep drilling during the year. The most remarkable bit of information is the discovery

Jan 1, 1937

By Jeffrey N. Schuyler

In order to implement the most efficient and cost-effective hydraulic fracturing stimulation treatment within a particular region, a thorough understanding of the in-situ stress state and rock properties is paramount (Smith et al., 1978; Warpinski et al., 1982). Several studies conducted in order to "characterize" formations have provided invaluable insight into the relationship between lithologic properties, depth, in-situ stress magnitude and hydraulic fracture orientation. These studies have substantiated that at shallow depths, rock properties such as tensile strength and permeability can exert a substantial influence on the geometry of an induced hydraulic fracture. In turn, these "directional properties" can be related to existing geologic conditions during the time of deposition or major diagenetic alteration of the rock body. As the depth of the "payzone" increases, the role of the in-situ stresses and therefore the prevailing tectonic conditions becomes the dominant factor in determining fracture geometry. However, reservoir properties cannot be ignored. The porosity, permeability, pervasive fabric element and directional elastic properties can have a significant influence on the success of those tests conducted to measure the in-situ stresses either directly or through secondary observations... for instance, pore-pressure effects on measurements of in-situ stress. The purpose of this paper is to provide, through the use of appropriate field and laboratory examples, a more thorough understanding of in-situ stresses, rock properties and their integrated effect on hydraulic fracture properties. In addition to highlighting and expanding the wide body of existing literature, the case studies cited are designed to encourage mutual transfer of technology from petroleum-related, rock-mechanics efforts to other disciplines.

Jan 1, 1984

By George S. Evans

CERTAIN American operators believe that desulphurizing in the ladle offers a means of increasing blast-furnace and open-hearth yields with the possibility of improvements in quality of the steel. In fact, several producers have experimented with practically all of the known desulphurizing agents, including both standard grades of the alkalies and special preparations that have been offered from time to time during the past several years. Some of these are regularly being used today in large-scale commercial operations, with good results. Also, it is the practice to treat off-sulphur casts in the blast-furnace ladle at a number of plants. It is not known, however, that anyone in the steel industry (American) has ever adequately equipped a plant for desulphurizing blast-furnace metal in an efficient manner as regular operating practice. The purpose of this paper is to illustrate the importance of correct equipment and proper handling for obtaining uniform and efficient results. As will be shown, at the temperature of molten iron the alkalies are instantly neutralized by any free slag present, dissipating their desulphurizing value. Entrained silicates are rapidly washed out of the metal bath by the highly basic soda slags and will be satisfied ahead of desulphurizing reactions with FeS. More or less of the reagent will always be used up through reactions with the refractory lining. Desulphurization will be limited to the action of the free alkali then remaining in the slag. Causes for the erratic results generally found with desulphurizing tests in blast-furnace transfer ladles would include, among other things, variations in the quantity of furnace slag coming down with the metal, and differences in the percentage of kish and entrained silicates in the different casts. As the alkalies instantly unite with any free slags or silicates present, these, with any kish coming off, both dilute the reagent and reduce the surface contact between the slag and metal, thereby retarding the desulphurizing reactions.

Jan 1, 1938

By Lee Morris, Charles E. Lawall

This paper represents the results of a study to determine the source, mode of occurrence and conditions influencing the flow and liberation of large volumes of inflammable gas in the Pocahontas No. 4 coal bed in southern West Virginia. A study of this kind is of interest in connection with mine ventilation, because in the removal of gases from coal mines it is very important to know the origin, the occurrence and laws of gas flow. The study was started in April, 1931, and the data and observations were obtained throughout a period of 15 months of field work. Geology The country where this study was made is mountainous and rugged; great cliffs, precipitous slopes and deep narrow gorges are found throughout the area. The outcropping rocks consist of stratified layers of sandstone, shale, limestone and deposits of coal of Carboniferous age. The Pottsville series of the Pennsylvanian, lying at the base of this period, cover the greater portion of the area. A stratigraphic section of the Pocahontas group of the Pottsville series is shown in Fig. 3. The older rocks outcrop in the extreme southeastern part of the area, but are under drainage in the central and northern parts due to the gradual northwest dip of the strata. The structure has a general northeast-southwest trend (Fig. 1). North of Dry Fork anticline the strata have been only slightly disturbed by movements of the earth's crust; it is now a long monocline. Southeast1 of Dry Fork anticline the strata are warped into great arches and deep troughs and are broken by overthrust faults. All of this folding is probably the result of the intense folding associated with the formation of the Appalachian Mountains. Pocahontas No. 4 Coal Bed The Pocahontas No. 4 bed, lying approximately 550 ft. above the base of the Pottsville series, is one of the thickest and most gassy coal beds in

Jan 1, 1934

By Robert McClurkin

Over a long period of time considerable attention has been paid to the chemical properties of the materials entering the iron blast-furnace charge. Infinite care has been used in the selection of materials having the correct chemical composition. Little attention has been paid to the physical properties of either the ore, coke or limestone. Until comparatively recent times the coke as produced, as well as the ore, was charged into the furnace without any attempt to maintain uniformity in physical size. Recently some work has been done along the lines of sizing of coke and in some cases the sizing of ore has been applied. In each instance marked results in the efficiency of operation have been attained. The effect of changing the physical size of the materials entering the burden has been reflected directly in the coke consumption. From the experience of operators and the results of numerous investigations which have been conducted on blast-furnace materials, it may be stated definitely that the physical properties of the materials entering the charge have as much bearing on the efficiency of the process as the chemical properties of these materials. Structure of Sinter On the Continent and more recently in this country iron-ore sinter has been introduced in blast-furnace burdens. The effect of the use of sinter has resulted in a material reduction in the coke consumption and an increase in the capacity of the furnace. The effect of the use of sinter is due undoubtedly to its porosity and to its physical size and, incidentally, to the chemical condition of the iron in the sinter and to the absence of combined water. Compared with Mesabi ores, all sinters are generally larger in size than the ore particles, and the structure of the sinter differs considerably from the structure of the ore. In sinter the mass is porous and open and makes available a great deal of surface for gas contact during the process of reduction. Most ores are relatively dense and nonporous and when the particle size is large the time element required for reduction is materially increased. The result of a very thorough investigation on iron-ore sinter by Schwartzll has shown that sinter is completely cellular in structure and

Jan 1, 1932

By P. R. Sheorey

Understanding of in situ rock mass behaviour has taken a step forward with the advent of the refined rock mass classifications of Wickham, Bieniawski and Barton et al. In this paper six case studies are given in brief showing how Barton's classification could be used in mining situations. The cases cover stability of roadway junctions under shallow covers, support pressure estimation in roadways in intact and failed rock conditions, determination of the safe unsupported span of a wide stope and estimating the stability of roadways in two contiguous seams standing 011 small pillars against puncture of the parting rock.

Jan 1, 1983

By H. W. Smith

This paper presents a review of developments to date in computer control practice, based in large part on Canadian experience. The basic problem examined is that of stabilizing control; matters considered are control strategies, hardware and software aspects of system implementation, reliability, human factors, and economic results.

Jan 1, 1976

By R. G. Paterson

THE usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired size and shape, and in one method' a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averaging a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer's knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. METHOD The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or diamagnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. DESCRIPTION OF APPARATUS Of many alternating-current bridge methods applicable,3 the one shown in Fig. I (Owen's bridge') was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by P1L1. It is connected to the bridge by about

Jan 1, 1941

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

By G. P. Boomsliter

IN previous discussions on stresses in hoisting ropes, little has "been said concerning the effect of the elasticity of the rope itself on the stresses due to acceleration. Laschinger1 has calculated acceleration stresses. for several cases but he has ignored the elasticity of the rope as a factor, except as it compresses the drum and stretches itself as it winds thereon. He also deals with steam plants and he shows the effect of the "jerky" start of the engine. This effect would actually be reduced by the elasticity of the cable. With the advent of the motor-driven hoist, new conditions have arisen. The jerk mentioned by Laschinger has been eliminated and smoother starting made possible. But the elastic properties of the rope seem to introduce considerable periodic acceleration stresses in the rope. The following discussion of acceleration stresses is based on the assumption of a constant acceleration at the drum. To be exact, the mathematical work is based upon the assumption that the top is moving upward with a constant acceleration, and ignores the fact that the cable is shortening as it winds. However, the effect of the shortening would be inconsiderable during the first part of the acceleration period. Most hoisting engineers make the assumption of constant acceleration at the drum. Under the older method of calculating acceleration stresses, this would be true with a constant torque motor. But if stresses vary, as this paper attempts to show that they do, constant torque would not give constant acceleration, although the velocity-time curves obtained in the full size test herein described showed that they approach rather closely to this condition, at least as nearly as could be measured.

Jan 2, 1927

By H. B. Emerick

An effort has been made to evaluate the individual influence of various factors in steel making and rolling operations upon the surface quality of semi-finished steel products. The thoughts expressed are not entirely theoretical, but rather are based upon several years critical observation of mill yields and rejec-tions and are supported by actual data wherever this has been possible.

Jan 1, 1940

By W. H. Emmons

INTRODUCTION MINERAL deposits that have formed by the various geologic processes, when exposed to air and water at or near the surface of the earth, break down and form new compounds that are stable under surface conditions. Mechanical disintegration of the ores proceeds along with chemical alteration which generally is attended by oxidation, carbonation and hydration. Essentially all minerals are affected-silicates, carbonates, native metals, sulphides, etc. Where iron sulphides are present, oxidation yields sulphuric acid, and in the presence of oxygen and iron, ferric sulphate, a powerful solvent, is formed. Above the water level, in the vadose or shallow zone, both air and water are present. Below the water level air is excluded and that which is carried down with water is removed from the solution by reactions with reducing materials. Above the water level, solution is the pre-dominating process; below the water level, precipitation generally is equally important. In some deposits, particularly above the hater level, valueless materials are removed from the ore, leaving certain metals in a more highly concentrated state. This type of alteration, which has been termed negative enrichment, is common in ores of iron, aluminum, manganese and certain other metals. Some gold deposits, particularly those in which the environment is unfavorable for solution of gold, have been enriched near the surface by removal of material other than gold. Certain metals are readily dissolved in an oxidizing acid environment. These include copper, silver and, under certain conditions, gold. In the presence of iron sulphides, deposits of these metals are likely to be leached above the water level. The metals are carried downward to depths where air is excluded, and where they may be redeposited, generally below the water level. Such enrichment by addition of metals has been termed positive enrichment.

Jan 1, 1933

By John A. Von Essen

To some, the paddle mixer may seem old as antiquity. Yet, as industrial mixing requirements become increasingly sophisticated in the late 20th century, it is proving more useful and versatile than ever. From water treatment applications to high-pressure reactors, the new and specialized demands in mixing have been met by a continuous evolution and adaptation of this basic workhorse design.

Jan 7, 1978

By Richard A. Walker, John P. Hager

The thermodynamic properties of the Pb-Au system have been determined between 750" and 1075°C by means of the cell Mo, Pb(1) |(PbO-SiO2){l) , SiO2(s) |Pb-Au(1), Mo The activities of lead and gold exhibit negative deviations from ideal behavior; the values of ? pb and ? the raoultain activity coefficients at infinite dilution, being 0.24 and 0.25, respectively, at 1200°K. The liquidus curve for the gold-rich region of the Pb-Au phase diagram has been determined from measure-ments on seven alloy compositions in the two phase region (liquid + Au(s)). The standard free energies of formation of Au2O(l) and Ag2O (1) have been estimated from cell measurements obtained by replacing the alloy electrode with pure liquid gold and silver. A new integral molar heat of mixing curve for the liquid Pb-Au system is presented and the results of previous studies discussed. The contribution of HM to FE was found to be small relative to TSE. THE use of galvanic cells of the type A(l) |A+Za|A - B(l) [I] provides an accurate means for the thermodynamic study of liquid alloy systems. In Part 1&apos; it was shown that cells of type [I] may be extended to higher temperatures and to a wider range of alloy systems if the ion A+Za is incorporated in an appropriate molten oxide phase, rather than in the classical fused salt electrolyte. In the following investigation the experimental method is extended to an investigation of the thermo-dynamic properties of the Pb-Au system by use of the cell: Mo, Pb(l) | (PbO-SiO2)(l), SiO2(S) |Pb-Au(l), Mo [] Previous measurements on liquid Pb-Au alloys were obtained by Kleppa2 by electromotive force measurements on a galvanic cell involving a molten chloride electrolyte. These measurements were confined to temperatures less than 830°C and compositions with X Pb > 0.2 because of the instability of the cell at higher temperatures. Later measurements by Kleppa3 on the heats of formation in the composition range 0.67 < Xpb < 0.98 were not consistent with the results by electromotive force measurement. The purpose of the present study is to extend the temperature and composition range of the thermodynamic properties and to obtain an independent measure of the integral molar heat of mixing over the entire composition range.

Jan 1, 1970

By A. Tobey Yu

The recent adverse economic climate has added further impetus to the demand for better-grade and lower-cost raw materials, for which increasingly larger quantities of muck are being moved and processed at higher unit labor costs. As a result, the cost impact of handling and shipping has never been as keenly felt by the mining industry as it is today. Thanks to joint innovative efforts by users and manufacturers, new and improved automated bulk-handling systems and devices are now blossoming everywhere to give the mining man the tools he needs to move ore, waste and concentrates more efficiently and economically.

Jan 1, 1970

By Robert E. Delavault, Harry V. Warren

Geochemistry in all its branches is playing G an increasingly important part in the business of mine finding. Although geochemical studies were commenced more than 50 years ago, interest in this subject did not become widespread until the late 1930&apos;s when in Scandinavia and the U.S.S.R. a whole series of investigations were initiated. Unfortunately for those in North America, the results of these investigations have only recently become available. In Canada and the U.S. geochemistry as a serious mine finding tool dates back only to the period following World War II. This article deals primarily with soils, which have found widespread acceptance as a useful tool in geochemical prospecting. Actually soils vary greatly in texture, structure, profile, and mineral background. Soil sampling poses no hardship for normal intellects, but it does assume an elementary knowledge of soil science and of the chemical problems involved in determining the absolute and relative amounts of a particular element in any particular soil.

Oct 1, 1956

By Frederic H. Wright

The secondary metals industry might well be defined as the group of remelters, smelters, refiners, and manufacturers that convert scrap metals or residues to commercial forms. In this industry, scrap metals and residues are processed to pro- duce refined metals, ingot alloys, fabricated shapes, and chemical products. Secondary metal is defined as metal recovered from commercial scrap, that is, scrap that has entered the processor&apos;s plant in scrap form. Metal recovered by a manufacturer from "home scrap" generated in his own plant is not considered to be secondary, because it represents part of the original stock that simply requires additional treatment before emerging as a finished product. In any economic study, a basic point of measurement must be chosen, and in the case of secondary metals, the melting pot or its counterpart represents the stage in which metal is converted from scrap to some more usable form. Beyond this point there is often no means to distinguish between secondary metal recovered from scrap and virgin metal produced directly from ore. In the last fifteen or twenty years the secondary metals industry has grown to major importance. Some consumers distrust secondary metals, but frequently this distrust serves only to prove an inability to keep up with the times. A rapidly decreasing number of manufacturers like to boast that they use only virgin metals, but a little investigation would show them that more than one third of all

Jan 1, 1943

J. C. WRIGHT.-The problem of organizing and maintaining a vocational class for those employees who are engaged in the mining industry depends on several most important factors. The first is the sympathetic cooperation of employer and employee; the second is to find the subject matter that must be presented to these men; and the third is to find the instructor who can present that subject matter. This is perhaps the most difficult, for we usually find a man who knows the material that is to be presented but is not a teacher or does not know how to organize his material. The man must know the subject matter from the standpoint of absolute contact with industry in order to be a successful teacher. I have come into contact with two kinds of schools organized in connection with mining occupations. In one type the instruction leans very largely toward elementary subjects, arithmetic, reading and writing and spelling; it is not of such a character as to help or improve the working man in his occupation in the sense that we are attempting when we speak of vocational education. In the other type of school, an engineer is usually employed as a teacher. He immediately begins to give the things with which he is most familiar and the instruction becomes such as only those who possess a high-school or college education, perhaps, are able to receive. In between these two schools is the school we are trying to, promote, a school that will meet the needs of those employed. MARGUERITE W. JORDAN,* Altoona, Pa. -Vocational education has become the business man&apos;s problem; for he is the keeper of that white elephant, labor turnover, and anything that will decrease the size of the monster is worthy of serious consideration. This vocational education can do; for it can supply many of those deficiencies in upbringing and. environment that make for the discontent and restlessness of our varied classes of unskilled labor: the Anglo-Saxon mountaineer; the Southern negroes who have crossed Mason & Dixon&apos;s line by the thousands, "searching satisfaction for our minds;" and the still greater number who have sought across the sea America, "the promised land.

Jan 4, 1919

By K. G. Davis

Dilute alloys of silzer in tilz haz been solidzjzed a1 controlled rules, in lzorizontal tubes 2 mrz and 0.5 rn in diam. Radioactive; tracer techniques we?-e used to study solute distvihutions along llze specimens and irmpurity substructures, as functions of the conditions growth. The results have heen mzalyzed using Burton, Prim, and Slichter&apos;s tnodel for the solute disty-ihution in the liquid ahead of an advancing solid-liquid interface. DECANTING techniques have been used to establish criteria for the formation of impurity substructure during solidification in several alloy systems An analysis equating the appearance of impurity substructure with the incidence of constitutional supercooling was developed,= in which diffusion was assumed to be the predominant mode of solute mixing in the liquid. Substitution of experimental data into the equations derived from the diffusion analysis gave reasonable values for solute diffusivity in the liquid. However, in these investigations solidification rates of 10 cm per hr and over were used, to minimize the effect of natural conection, whereas for crystals of high perfection lower solidification rates are needed, usually between 1 and 5 cm per hr. A knowledge of the conditions under which impurity substructures will be formed at low growth rates, and the degree of segregation to be expected, is therefore of interest. In the present investigation, radioactive-tracer techniques have been used to study the effect of growth rate, initial solute concentration, and size of specimen on the formation of substructure in uni- directionally solidified rods of dilute silver in tin alloys, over a range of growth rate between 0.5 and 10 cm per hr. Criteria for the formation of substructure were established by auto radiography. This was believed preferable to the decanting technique, for the relationship of the structure on a decanted interface with that of the freezing interface is not clear, since a layer of liquid is left on the surface following decanting.&apos; The effect of substructure on the distribution of solute along the rods was also investigated. EXPERIMENTAL The procedure for sample preparation has been described in detail by einber. Alloys were prepared from tin of 99.999 pct purity and silver of 99.99 pct purity. A"&apos;, an emitter of both y and 0 radiation, was used as tracer. Samples of the alloys were drawn up into silica tubes with inside diameters 0.5 or 2 mm, remelted in a horizontal furnace, and solidified at controlled rates. A few centimeters of the samples were left unmelted for a measure of the initial concentration. Total sample length was approximately 20 cm. The temperature gradient in the furnace was kept constant at 36°C per cm in the region corresponding to the melting point for tin. To find how well this corresponded to the actual temperature gradient in the melt, a thermocouple of 38-gage wire was electrically insulated with a thin layer of Sauereisen cement and placed within one of the 2-mm-diam tubes, which was then filled with tin. The maximum diameter of the coated wire was 0.5 mm, the bead of the thermocouple junction being no larger than the diameter of the wire. A plot of temperature vs distance traveled by the furnace is given in Fig. 1 for a rate of furnace travel of 1 cm per hr. The temperature gradient in the liquid

Jan 1, 1967

By T. Prof. Egleston

DURING the last winter we have been actively engaged in the School of Mines in search for boracic acid. This has been owing to the fact that Mr. M. W. Iles, assistant in the qualitative laboratory, has discovered a test for that substance which makes its discovery exceedingly simple instead of being, as previously, very difficult. It consists in powdering the mineral, calcining it, then moistening it with sulphuric acid, and heating on a platinum wire until the sulphuric acid is expelled. It is then moistened with glycerin and made to take fire. If boracic acid is present it infallibly gives a green flame. It is not at all surprising, under such circumstances, the test being so easy, that boracic acid has been found by the students in a great many cases where its presence was not previously suspected, and in some where its detection was previously too difficult to warrant looking for it. We were not prepared, however, for its discovery in Lake Superior iron ores, and were disposed at first to think that a mistake had been made. After, however, it had been frequently reported in these ores it was considered worth while

Jan 1, 1877