Search Documents

By W. B. Weeks, H. K. Shearer

The year 1937 brought to south Arkansas increased drilling activity and production. Oil production amounted to 12,159,440 bbl., an increase of 1,504,500 bbl., or 14.1 per cent over 1936. This was the largest production since 1931, and the first annual increase since 1925, when the deeper sands at Smackover were developed. There were 177 wells completed during the year, with 103 oil wells, 6 gas wells, and 68 dry holes, an increase of more than 100 per cent over 1936. Of the 56 wildcat wells drilled, 52 were dry and 4 produced oil. Two new fields, one important extension and three minor extensions were discovered. The trend toward deeper drilling is shown by the fact that 97 wells were more than 5000 ft. deep, including 80 over 6000 ft. and 13 over 7000 ft., although the depth record of 7973 ft., made in 1935, was not exceeded. Geological Section Deeper and more extensive drilling during the past few years, not only in south Arkansas but also in adjacent parts of north Louisiana and east Texas, has furnished much important geological information and has brought out some very unexpected facts in regard to structural and depositional conditions in the series of formations laid down in the interval between the end of the Pennsylvanian and early Cretaceous time. It is now evident that an important basin of salt deposition existed in the Arkansas-Louisiana-Texas area, but it is still an open question whether this salt basin was contemporaneous and continuous with the even larger Gulf Coast salt basin extending from Mississippi to Mexico. The accompanying columnar section (Fig. 1) shows the producing zones and names that have been applied to the several subsurface formations, most of which have no outcrop equivalents. This is for the convenience of readers unfamiliar with recent developments, but the correlations and nomenclature cannot yet be considered final. These formations will be discussed in more detail in various papers to be published in the near future.

Jan 1, 1938

By A. M. Gaudin

THIS paper presents, with the help of colored photomicrographs, the new method of mineral identification termed "selective iridescent filming." This method pertains to the field of determinative mineralogy, which it provides with tools for: (1) phase identification, (2) solid solution analysis. The method should be particularly useful in the applied fields of: (1) paragenesis of ore deposits, (2) mineral dressing, (3) mineral synthesis and study of phase equilibria.

Jan 1, 1938

By Ralph Sweetser

PROGRESS in blast-furnace practice during 1922 has been in the direction pointed out in my article in the March, 1922, issue of MINING AND METAL-LURGY; this advance has been very satisfactory in spite of the difficulties caused by the great coal strike and the railroad strike. The progress, especially in increased tonnage, has been brought about, not by increasing the size of the furnaces, not by improved mechanical devices, but through the application of better blast-furnace practice; the advance has been metallurgical rather than mechanical. The increase in production per stack, has been more pronounced than in any period since the time that James Gayley began to break blast-furnace records in Pittsburgh. These big tonnages have been made in furnaces designed to make 550 to 600 tons of pig iron per day; but several such furnaces have had monthly averages of between 700 and 800 tons per day with a corresponding reduction of cost, and a reduction in the number of man-hours of labor per ton of pig iron. During this period there has been a wider acceptance of the fact that satisfactory blast-furnace results are more dependent on coke quality than on any other factor. There has always been much rivalry among blast-furnace men in making new tonnage records, and many schemes have been used for getting out big pro-duction, but the blast-furnace man cannot make the high records all by himself; it is necessary for him to have the cooperation of the entire management, and also the help of the organization that makes his blast-furnace coke. Herman Brassert has said that "there is no blast-furnace practice possible that can wholly overcome the effects of bad coke." In the past; the blast-furnace superintendent has often been under suspicion if he complained about the quality of the coke in times of unsatisfactory blast-furnace results, but it is now conceded that if the quality of the coke is not right, complaints are not necessarily made as an alibi.

Jan 5, 1923

By S. H. Ash

Mass production methods, although increasingly important for economic reasons, create new hazards, remove many hazards, and improve health and safety by reducing exposure and obtaining better supervision. Such methods must be efficient or be discarded. Skilled workmen are required who must be trained to utilize equipment that replaces picks, shovels, and explosives. The effects of working conditions on the health of workmen have long been evaluated in noncoal mines. Studies and action programs relating to environmental health hazards in the mineral industry have placed particular emphasis on dusts. The anthracite industry is conducting an action program on the problem of dust. Segments of the bituminous industry are now conducting similar investigations. An industrial hygiene survey of coal mining in the State of Washington has been conducted and the results published in 1949. (State of Washington, Department of Health, I. H. Bul letin 4.) Chest X rays were obtained from miners in the six major coal-producing counties. State Health Department mobile X-ray equipment was set up at most large mines. Participation was on a voluntary basis, and response was obtained from 70 percent. Important in successful mining safety programs are training programs for supervisors and workmen alike. These programs recognize that the employe is the focal point in injury prevention and are planned and function around him. During the war, industries had to compete with each other for workers and to obtain and hold good workers, working conditions had to be made attractive. The average age of the mine worker increased, and, contrary to what many expected, mining injury rates decreased rather than increased. To attract competent workers, risks to life and limb, as well as laborious tasks, have to be reduced, and an experienced worker is indispensable for safety. Young men are returning to modernized mines. Mass production methods and equipment are more to their liking; jobs are more remunerative, demand action, and require special training and skill that give them the mark of a craftsman. Such workmen can be taught safe methods.

Jan 1, 1950

By C. E. Reistle, G. L. Nye

The East Texas field is in Smith, Rusk, Gregg, Upshur and Cherokee counties, Texas. The discovery well was completed Sept. 8, 1930, near the eastern limit of the field. Within less than one year the new field became the dominant factor in the world production of crude oil. On Aug. 16, 1931, eleven months after completion of the discovery well, there were 1644 wells in the field, and the average daily production was 584,475 bbl. Since that time the number of wells has increased to 8195 on Oct. 1, 1933, and the field has produced 385,979,691 bbl. of oil. The geology of the East Texas field has been discussed by Lahee,1 Levorsen,2 Minor and Hanna3 and others, and it will not be discussed in detail here. The field is a structure of the monocline type on the westward dipping homocline between the Sabine uplift and the East Texas geosyncline. Production is obtained from the Woodbine group, which has been truncated and then sealed by the Austin chalk, which rests unconformably upon it. The oil-saturated part of the sand lies bettween a sub-sea depth of 3050 ft. on the east side of the field, where the Woodbine sand stops and the Austin chalk rests directly upon older formations, and a sub-sea depth of 3320 ft., which was the average depth of the water table in the sand at the time the field was discovered. The field is about 40 miles long and has an average width of approximately 4 1/2 miles. The area within the proven limits of the field is close to 116,580 acres and the normal Woodbine water underlies nearly 62,000 acres on the western side of the field at the present time. The field is unusual in several respects: (1) the tremendous size of the reservoir system and the quantity of oil in place; (2) the large area of the oil and water contact, which makes water movement possible into the oil-bearing part of the structure; (3) the absence of free gas within the main producing sand of the field. Changes in the reservoir pressure during the production history of the field have been greatly affected by

Jan 1, 1934

By H. A. Doerner

METALLURGICAL problems relating to manganese and chromium ores have striking similarities. Ferroalloys, essential to the steel industry, are produced from both ores. Most of these alloys are obtained from imported ores, as domestic deposits have not yielded enough ore of metallurgical grade to meet more than a small fraction of vital needs. A survey of domestic manganese and chrome de- posits reveals numerous small, dispersed bodies of fairly good ore, none of which appears to be capable of yielding significant amounts of marketable products. To stimulate development of such deposits and to increase Government stockpiles, General Services Administration is offering $115 per long ton for limited amounts of chrome ores and $110 per long ton for 48 pct manganese ores that meet metallurgical specifications, with bonuses or penalties for grades above and below specifications.

Jan 4, 1953

By J. T. Burwell

THE crystal orientation in silicon iron that has been given a particular treatment described by Goss,1 has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualita-tive. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200, It is now generally agreed that Goss's original conclusion' that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom.

Jan 1, 1940

The only definite information available is for the years 1875, 1878, and 1879 and 1880. The total figures in Table 48 are estimated. [ ]

Jan 1, 1942

By M. Semchyshen, G. A. Timmons

P. A. Beck (University of Illinois, Urbana, 111.)—An interesting result of this work is the fact that in cold rolled molybdenum sheet complete loss of work hardening is obtainable on annealing, without change in texture. The retainment of the cross-rolling texture on soft-annealing is particularly significant, since this is essentially a single orientation texture, where texture retainment could be achieved by only one of the two niechanisms which produce this effect in aluminum,16 namely by recrystallization in situ. Recrystallization in situ was originally discovered by Collins and Mathewson (1940) and by Crussard (1944) as a phenomenon taking place on annealing in relatively mildly deformed single crystals of aluminum. It now appears to be a major (in many cases the major) mechanism of annealing of severely cold rolled poly-crystalline material, not only in aluminum,le but in metals as different in character as beryllium," tita- nium,'" and molybdenum. All these data now confirm the general validity, at least for more or less pure metals, of the interpretation of the annealing process given a few years ago by Smith.'" The whole question of recrystallization is now reopened. Indeed, it appears that recrystallization, as defined traditionally, may not occur at all, since at the time "deformed material" is absorbed by "recrystallized grains," it has already become completely strain free by recovery and "recrystallization in situ."

Jan 1, 1953

By Sam Rosenblum

The anomaly ratio is obtained by dividing the analyzed value of an element by the anomaly threshold value of the element. The sum of anomaly ratios for all anomaly elements in a sample may be compared with similar sums for other samples, so that samples having the greatest anomaly- ratio totals can be recognized easily. In partial or full suites of ore elements the we of anomaly ratios is more meaningful than use of analyzed value because the ratios quickly indicate how use of analyzed values because the ratios quickly indicate how anomalous some elements are, and call attention to samples and

Jan 1, 1982

By C. A. Siebert, G. Sandoz

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By G. Sandoz, C. A. Siebert

OIL quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State `A'-Vapor Blanket Cooling-In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage `B'-Vapor Transport Cooling- Termination of the `A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage `C'-Liquid Cooling--The `B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the `B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage `B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 2 ½ -in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and 1-in. stream height, and (2) a ½ -in. orifice and a 3 ½ -in. stream height. In all cases the samples were suspended so that the quenched end was ½ -in. above the orifice. The steel used was an NE 9450 having the following analysis: [ ] Some tests were run on an NE 8740, 3312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been omitted' from this paper. The test bars were machined from 1 1/8 -in. stock to 1-in. diam by 4 in. long.

Jan 1, 1948

By G. Sandoz, C. A. Siebert

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By Albert H. Chester

DURING the summer of 1875 I visited some of the iron mines of Houghton County, Mich., and was quite interested to observe the progress made there within a. few years. Working in open pits is gradually giving place to underground work in most of the mines where this system is practicable. In some cases, as in the Lake Superior Mine, the body of ore is so irregular, and the deposit so liable at any time to be pinched out, or nearly so, that it has been found impractical, if not impossible, to lay out any plan for systematic underground work. But in many other mines the deposit is so regular in character, that the work can be laid out in shafts at regu¬lar intervals, and a series of 60 feet levels. The Michigammi Mine, opened in 1872, and first worked in 1873, is arranged on this plan, though some quarrying is still done. But the men are being put at overhead stoping as fast as it can be got ready for them, and before long it will all be worked in this way. The New York Mine is undergoing a similar change to the pillar system, and several others have either been changed, or it is about to be done. My principal object in visiting this region was to obtain samples from some of the important mines, so as to be able to answer the question : "What is the average percentage of iron in the Lake Superior ores?" Most iron furnaces work on mixtures of ore, so that it is impossible to tell, from their records, just the percentage in each one.

Jan 1, 1876

By Oliver Bowles

THE inorganic non-metallic minerals, that is, the non-metallics exclusive of coal, oil, gas and related minerals, constitute the basic raw materials for a number of essential industries. It is estimated that the value of the raw materials in this group produced in 1919, together with certain of the primary products ordinarily manufactured at the mine, exceeded $800,000,000. They are employed chiefly in the building, agricultural, and chemical industries. It has been estimated, by the Bureau of Mines, that approximately 00,000,000 worth of non-metallic minerals and their products were used in the building trades during 1918; with the great increase in building since that date and the increased cost of materials, the value of non-metals used in such industries during 1920 probably exceeded $500,000,000. The chief of these materials are cement, building stone, crushed stone, sand and gravel, clay products, lime, gypsum, glass materials, slate, talc and soapstone. In many of the producing industries of this great group, the waste is so great that the expense of handling it is an important item in the production cost. The utilization of waste is receiving unusual attention in many of the non-metallic industries at present. The most obvious advantages of such utilization are: (1) Conservation of mineral resources, (2) the removal of waste heaps that in many places obstruct development, (3) manufacture of new and useful products, (4) reduced production costs through elimination of a large part of the item of waste-disposal expense. In many industries there is keen competition between producers of various products used for the same purpose, so that advantage will accrue to the manufacturer who is able to reduce his production costs.

Jan 1, 1921

By Takuski Stanislaw, Alfons Krawiec

Rock bursting is a particular hazard in the pit-coal mines of Poland due mainly to the physical-mechanical properties of the rock and the geological-tectonic structure of the Upper Silesian Coal Basin. Mining and geophysical methods of predicting and preventing rock bursts are discussed. These include: seismologic methods, various kinds of shock blasting, torpedoing, and injecting water under high pressure.

Jan 1, 1978

By I. A. Lange, A. M. Richardson

Although methods for determining shaft lining thickness are well documented, little attention has been given to the design of station breakouts and other related shaft ground support structures. This paper discusses design of selected shaft structures for the Cathedral Bluffs project, a planned 54-kt/d (60,000-stpd) oil shale mine in western Colorado. Design philosophy and construction sequences used in the three completed 520-m (1700 ft) deep, 4.6-m (15 ft) to 10.4-m (34-ft) diameter shafts are described.

Jan 1, 1984

By W. Arthur White

Underclay squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay-making it more plastic-or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards.

Oct 1, 1956

By W. H. Coghill, A. M. Gow, M. Guggenheim, A. B. Campbell

The object of this paper is to discuss the fundamental principles of ball milling and to present some observations which have been made in laboratory and plant investigations. The discussion will be limited to wet grinding of ores in cylindrical mills, but doubtless many of the principles involved will be equally applicable in the other fields of fine grinding in which mills of the same type are used. In the concentrators of the United States there are about 650 ball, rod, or pebble mills, operating or ready to operate, and these have about 100,000 connected horsepower. For grinding in cement plants there is about three times this connected horsepower, and other industries have an unestimated amount, all used for the general type of grinding that is to be discussed here. It is true that these figures do not represent stupendous amounts of power, but when one considers that ball milling is often the ((bottle neck" in a concentrator and that it often accounts for the largest single item in the cost sheet, the importance of a comprehensive understanding of the principles of ball milling can be appreciated. Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses, or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespective of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison, a new philosophy in the study of ball milling. Briefly, this '(new philosophy" consists of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced varisbles, with emphasis on the latter.

Jan 1, 1935

By Tom W. Pfeifle, Paul E. Senseny

INTRODUCTION Engineered structures such as mines, shafts and tunnels, and storage caverns for hydrocarbons, chemical s and brine are being built in natural rock salt formations in increasing numbers. In addition, salt formations are being considered as potential hosts for mined, nuclear waste repositories. The popularity of these formations for engineering purposes stems from the many favorable commercial, physical, and thermal characteristics attributed to the material itself. Not only have the formations been stable and free of dissolution for hundreds of millions of years, but the salt is fairly easily mined and has very low permeability, low water content, and high thermal conductivity. Another characteristic of salt is its tendency to flow or creep when subjected to a shear stress. Although this behavior may be desirable in certain instances, it may be detrimental in other instances since the creep rate may be large enough to produce deformations that tend to reduce the volume of storage caverns or to restrict access to mining operations. In either case, the engineer is faced with the problem of accurately predicting the long-term structural deformations under various combinations of stress and temperature and is required to compare these deformations with long-term design criteria. In the laboratory, deformation-versus-time curves obtained at constant stress and temperature show that creep of salt is similar to creep of many other crystal line solids. Figure 1 shows a typical deformation-versus-time curve for salt. When a shear stress is first applied, the rate of deformation is high, but decreases monotonically. This initial behavior is called transient or primary creep. At some time, the deformation rate no longer decreases but continues at a constant rate. This behavior is called steady-state

Jan 1, 1982