Search Documents

By John T. Galey

In all, 210 wellst were completed in southwestern Pennsylvania during 1939, which is 59 more than were drilled during the preceding year. Of this number, 137 were gas wells, which is a considerable increase from the 81 completed during 1938. Only 25 oil wells were completed, as against 28 in the previous year, and 28 dry holes, 6 more than last year. Shallow Development—Gas The increase in the number of gas wells is largely the result of a search for additional gas in Armstrong and Indiana Counties. Although a considerable number of wells were drilled in the latter county, the majority of them produced less than 100 M cu. ft. initial open flow. In Armstrong County, a new pool was opened in Cowanshannock township, producing from the third Bradford sand. Several large wells were obtained there, one of which produced an initial of nearly 12 million cu. ft., with a reservoir pressure of 1100 Ib. However, the productive area has been fairly well outlined by further drilling and shows that the pool covers only about 800 acres. The sand is 20 to 30 ft. thick, and probably has 5 to 6 ft. of pay. Thus this reserve is not an important one. Several wells were found in Menallen township, Fayette County, where the Big Injun sand has been having a play for the past three years, but the activity there is much less than a year ago. Oil On the west side of the Bradford sand gas pool, Cowanshannock township, Armstrong County, a well was drilled which flowed 100 bbl. the first day from the Tiona sand. The probability is that this well is a freak, as the Tiona has been drilled within a fairly close distance on every

Jan 1, 1940

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

By R. E. Somers

THE Appalachian field is notable for four tests drilled in recent years to depths of over 7000 ft. and for one commercial gas well at 6822 ft. The latter is the Ligonier well and produces from the Oriskany FIG. I.-NATURAL GAS PRODUCTION OF PENNSYLVANIA AND WEST VIRGINIA. sandstone. Together with several other comparatively deep tests, these holes were drilled in search of natural gas, to make up for the decline in production of the field. The production curve of Pennsylvania FIG. 2.-EAST WEST SECTION OF APPALACHIAN FIELD. (AFTER ASHLEY AND ROBINSON, PENN. G. S.) and West Virginia from 1907-21 is given in Fig. 1 to illustrate the heavy decline from the peak of 1917. This diminishing supply has also been shown by Moyer,1 on the basis of decreasing rock pressures.

Jan 3, 1924

By D. V. Fites

Criteria for deciding when rock should be ripped and what ripping equipment and techniques should be used in given situations are discussed in this article. The relation between ripper performance and seismic wave velocities in various types of rock is also discussed. The ripper is not a new tool. In fact, it dates back as far as the Roman Empire. The Roman's ripper-mounted on wheels and shaped something like a plow — was pulled by oxen and used to loosen the earth for the shovelers and basket carriers building the Appian Way. There are records of rippers being used in this country in railroad construction between 1860 and 1880. However, the ripper as we know it today did not appear until about 1930. Tractor-drawn models were in use in 1931 on the Hoover Dam project. At that time they weighed about 7500 lb and were pulled by tractors with about 75 flywheel hp and up to 30,000 Ib total weight. The chief shortcomings of trailed

Jan 1, 1969

By N. E. Maccallum

Almost half a century has passed since the Siemens brothers, after tedious and costly experiments, finally began the manufacture of open-hearth steel. The furnace of that time was very small, having a hearth-capacity of from 3 to 4 tons, and we can appreciate the wonderful development that has taken place in those 50 years by the knowledge that to-day furnaces of 50 times the original capacity are in operation. As the new steel process assumed importance, and furnaces began to grow in number and in size, a question arose, to which no satisfactory answer has ever been given, and that was: aWhat is the safe and economical limit of the open-hearth furnace ?" Various stopping-places have been suggested, and 20, 30, 40, and 50 tons have each been advocated, but all such arbitrary restrictions have been passed, and 60 tons would probably represent the average furnace, although in a few instances from 70 to 80 tons are regularly tapped into one ladle. The furnaces which are the subject of the present paper have gone far beyond even these limits, and since, in my opinion, they mark another step in the progress of open-hearth steel, they will be considered fairly and frankly, in order that those to whom the matter may be of interest may be able to judge and form their own conclusions. Short accounts of the work of these furnaces have appeared from time to time in various technical journals, of which the following is a brief résumé. These furnaces are the property of the Phoenix Iron Go., of Phœnixville, Pa., and their distinctive and important feature is, that they charge to twice the capacitl of one ladle, and tap simultaneously into two ladles, with a device for controlling the flow into either. In this way the capacity of the furnace is not limited, as formerly, but heats of any size within the capacity of two ladles may be charged.

Jan 1, 1913

By C. S. Samis, J. C. Mitchell

Sodion activity data have been obtained for the Na-A1 system for sodium concentrations in aluminum between NN, = 25 . 10-and 300 x 10'. This concentration intert-a2 encompasses those sodium concentrations nor1)zally encountered in aluminum reduction cell operation. The sodium activity data were measured by a two-phase equilibration of sodium between a lead and an aluminam rich phase. The Na-Pb system was emplojed as a reference for the determination of the actiz7itj 0.f sodium. The activity of sodiin in aluminuwz exhibits large positi2.e deviations frorn ideality and a strong dependence, on concentration below NN, = 100 x 1K6. The inteated data indicate that the activity of aluminium is equal to its mole fraction over the range of miscibility of the Na-A1 sgstem. The data on the Na-A1 binary have been combined with experimental data on the cryolite-A1 system at 1025°C to obtain the activities of Na F and AlF, in liquid cryolite oz2er the cornposition 1-ange encountered in aluminum cell operation. The results are in agreement with activities calculated from the NaF-AlF, phase diagram. ALUMINUM is produced commercially by the electrolytic reduction of aluminum oxide dissolved in molten cryolite. There is considerable controversy over the actual mechanism of the discharge processes, but sodium potentials in the systems appear to play an important role in the reduction mechanism. The metal-salt reaction involving NaF and aluminum to produce A1F3 and sodium is responsible for the presence of sodium in the aluminum metal phase. Additional sodium may be produced from the simultaneous deposition of sodium and aluminum at the cathode as a result of a cathodic overvoltage. runert' has suggested that sodium gas at atmospheric pressure would be the result of reaction between cryolite and aluminum at 1000°C. Subsequent investigations have shown that production of sodium at atmospheric pressure does not occur. These later investigations can be conveniently separated into two categories. The first involves sodium, aluminum, and cryolite, in which the sodium activity was measured. The second includes a lead phase for sodium activity measurement. Jander and errmann,' studied the reaction: at 1090°C in alumina crucibles under an atmosphere of dry, oxygen-free nitrogen. The equilibrium constant for the reaction was expressed in terms of concentration. Their results in Fig. 1 show an increase in sodium content of the aluminum with increasing NaF/A1F3 weight ratio. Pearson and waddington3 performed similar experiments at 1000°C. Their results are included in Fig. 1. Dewing and ollinshead have measured the sodium content of aluminum as a function of the NF/AF, ratio at 1025"C, Fig. 1, and ewin' measured the sodium content of the aluminum in a system involving the solid reactants NaF, cryolite, and liquid aluminum. This reaction is different from those discussed above. Two solid phases, NaF and Na3A1F6, and a liquid aluminum phase were present. The sodium concentration in the aluminum was determined by the temperature. Dewing's measurements covered the temperature range 679" to 896°C. Omo, Matsushima, and 1t02" investigated the equilibrium 6NaF ential thermal analysis. Stokes and Frank6 determined sodium activities by

Jan 1, 1970

By Yoon T. Auck, Milton E. Wadsworth

Column leach studies of two low grade prophyry copper ores were made with variables of size, flow rate, pH, drainage rate and tempature. Evidence is presented to show that, in some types of ores, sulfide minerals block leaching channels and regulate the rate of dissolution of gangue constituents. Basic iron sulfates, dissolved by introducing acid, provide oxidizing agent in the form of ferric ion in the absence of oxygen. Ferric ion then acts to release copper from the ore. Oxygen up-take was found to increase with the lowering of the pH and to follow parabolic kinetics attributable to the precipitation of basic iron salts within the pore channels. Slow drainage of residual gravitational water can seriously retard oxygen up-take during oxidation for particles in the coarse sand range. A model is presented for dump leaching in which a reaction zone connected by channels to the surface of the ore particle moves topo-chemically during the course of the reaction.

Jan 1, 1973

By W. C. Maurer

Although millions of feet of rock are drilled annually, the basic drilling mechanisms involved are not well understood. The primary reason for this lack of knowledge is because the basic principles of rock failure are not well understood and rock failure is the primary mechanism in drilling. A better understanding of the drilling mechanisms would enable a more scientific approach to the design and use of drills and bits. The paper reviews several models which have been proposed to explain various aspects of the different drilling methods. These models are described and their limitations and areas of application are discussed. Drilling rate relationships are developed and related to the basic rock failure mechanisms. TYPES OF MECHANICAL DRILLS There are three basic methods of mechanically attacking rock: 1) percussive action, 2) rotary action, and 3) combined rotary-percussive action. A percussion drill applies a force perpendicular to the rock surface and the bit moves into the rock perpendicular to the surface, forming a crater beneath it (Fig. 1). A rotary drill applies a constant thrust to the bit while a torsional force moves the bit parallel to the rock surface, breaking the rock ahead of it. A rotary-percussive drill applies both a rotary force and a percussive force to the bit which moves into the rock at an angle to the surface. The commonly used drills can be classified as: rotary-drag, diamond; percussive-hammer, piston, churn; and combination-rotary-percussive, roller.

Jan 1, 1967

By R. M. Brick, Arthur Phillips

The normal method of preparing metallic alloys for commercial use involves the preparation of a melt containing the given components in the chosen proportions and allowing the homogeneous liquid mass to solidify in a mold of the desired form. The solidification is frequently accompanied by a segregation of the alloying elements in different parts of the casting. When the segregation is occasioned primarily by marked differences in density of the solid and liquid phases, it is termed "gravity" segregation. When the segregation conforms to a selective freezing in harmony with the teachings of the equilibrium diagram of the alloy system—i.e., the lower melting phases are concentrated in the regions of the casting last to freeze—it is often referred to as "normal" segregation. However, in many cases the lower-melting part of the system is concentrated in the parts of the casting first to freeze and the result in this case is termed "inverse" segregation. To complete the terminology of the subject, normal segregation in a single phase is usually called "coring" and the word will be used in that sense in this paper. Inverse segregation, particularly when the liquid phase is exuded or sweated out on the surface of the casting, is sometimes called "liquation." Unfortunately, some ambiguity has arisen from the use of this term and it is perhaps advisable to confine its use to the dictionary definition; namely, "The separation of two phases by heat sufficient to melt one but not the other." The gravity and normal types of segregation are both well understood and to some extent, are controllable by taking advantage of the most favorable cooling rate for a given casting condition. Inverse segregation has received considerable attention from several investigators but none of the theories offered seem to account in a convincing way for the many examples of this type. The observations made in the present work on segregation in single crystals, and in some other castings, tend to support one theory of the mechanism of inverse segregation and definitely to

Jan 1, 1937

By J. B. Pullen

THE United Verde mine is in the north central part of Arizona, on the. north-easterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruffner and associates in 1877. In 1888 the late Senator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 189o to date. GEOLOGY The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre-Cambrian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-ft. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. A plan and vertical section of the mineralized zone showing the principal geological features is shown in Figs. I and 2. GENERAL DESCRIPTION AND PHYSICAL CONDITION OF MINE After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes -mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became difficult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1941

By H. De Cizancourt

The Pechelbronn (Alsace) field is the only important French producing field. During 1934, development was carried on as in previous years. The total output of this field reached 553,575 bbl. in 1934, showing a slight decrease from the 1933 figures. Of the total, 315,000 bbl. (56 per cent) was extracted by drilling, while 238,875 bbl. (46 per cent) was obtained by means of shafts and galleries. Exploration of deep Jurassic and Triassic horizons was still in progress at the end of 1934. A deep well reached the Upper Triassic at a depth of 34 m. (2736 ft.). (Information kindly supplied by M. S. Mena, Directeur Technique.) As mentioned before, the small Gabian field (Herault) is gradually being exhausted. No drilling operations were undertaken in 1934, the small production being restricted to the pumping of old wells. Two exploration wells, noted as "drilling" at the end of 1933, were completed in 1934; viz., Lavelanet (Ariége) at 3785 ft. and Santenay (Niévre) at 2578 feet. French Possessions Algeria.—No drilling at Tliouanet. Out of a total of 100 wells drilled in the area, only 8 are still producing. No exploration work is reported during 1934 in Algeria. Tunisia.—Two wells completed; one well drilling at the end of 1934. A total of 11 wells is reported to have been drilled before the beginning of 1935; out of these, 8 were completed before the present program was begun. Morocco.—Exploration work progressed actively last year. The outstanding event was the coming in of Ts. 26 well at 1243 ft. This well took fire, therefore great difficulties were encountered in the accurate measurement of initial production; the figure of 1500 bbl. of oil given here is a near estimate. Oil flowed accompanied by a great amount of water. The apparent decrease of drilling operations in 1934 is explained by the increase in field activities after the results of Ts. 26 were known;

Jan 1, 1935

By Carroll F. Hardy

THE position of the coal industry has been affected by a wide variety of developments in the production and use of energy. The tempo of development and change has been increasing and the end is not in sight. Legislation is currently being proposed for commercial use of atomic power, and the employment of atomic energy in significant quantity will probably occur about the same time as the decline in production of petroleum and natural gas. But these developments are in the future and have little immediate effect on utilization and marketing of coal. While no one should try to suppress or retard the development of a new and economical source of energy, both the coal and private utility industry should be allowed to question how the nuclear power is to be used, who is to use it, and who is going to pay for it. The taxpayers have a monopoly on fissionable material and the knowledge to employ it. Any commercial use must stem from this source. It is not hard to visualize either taxpayer- subsidized private utility atomic power plants on one hand and super TVA's on the other. In view of the gains of gas and oil in the home heating field, it is interesting to compare the 1940 and 1950 census reports on the kind of fuel used for heating in occupied dwelling units. Table I shows that whereas coal provided 77 pct of the fuel for central heating (furnaces and boilers) in 1940, it was down to 45.4 pct in 1950. However, only about 1 ½ million units were lost in this 10-year period.

Jan 3, 1954

By E. Baker, David Donoghue

Legal and legislative matters constituted the outstanding features of proration in Texas in 1932. From East Texas emanated most of the political, legal, technical and industrial activity. Conroe and Thompson developed into fields of major importance. Proration orders were issued by the Railroad Commission on many of the producing fields of the Gulf Coast and West Texas not covered in previous years. In Yates, Penn Pool, Winkler, Van, the Panhandle, North Texas and West Central Texas there were 110 changes of importance, except in allowables. New proration schemes were introduced in East Texas, Conroe, Thompson, Saranosa, Government Wells, Tuleta and Howard-Glasscock. Little progress was made in administration or technical development. Legal and Legislative Matters Proration first began in Texas in 1927 as a voluntary attempt to divide the market outlet of a field on an equitable basis. The statutes then in existence were considered somewhat archaic and the Railroad Commission's authority was limited. Subsequent efforts to strengthen the laws were not wholly successful. The 1929 Conservation Act made no mention of market demand but declared that the term "waste" did not mean " economic waste." With the passage of the Pipc Line Act of 1930, providing for ratable purchasing, it was the opinion of many lawyere that a legal means of proration had been found. The 1931 law had ths same provision as that of 1929 with respect to economic waste but specifically prohibited limiting of production to market demand. The law passed Nov. 12, 1932, omitted reference to economic waste and specifically provided for limitation of production to reasonable market demand. Vigorous attacks were being made in State and Federal Courts on the constitutionality of the laws and the validity of the Commission's orders. In Peoples Petroleum Producers, Inc. et al. vs. Lon A. Smith et al., which had been heard before a three-judge U. S. District Court in Houston on May 28, 1932 and again on Sept. 19, the Court's decision for plaintiffs, released Oct. 2, influenced in a large measure the calling of the Legislature and the passage of the Market Demand Law on Nov. 12.

Jan 1, 1933

By G. W. Healy, W. Craft, D. C. Hilty

By means of a theoretical extension of the Cr-C temperature relation in molten chromium steels to low chromium contents and by a correlation of the ratios of chromium to iron in the slag and metal, a method has been developed for estimating the amount of metallic oxidation during the oxidizing period of a chromium steel heat. Application of this method has indicated that due to temperature limitations metallic oxidation may be excessive for very low carbon steels charged with more than a small amount of chromium. IN the melting and refining of chromium steels the oxidation of carbon to a low level is accompanied by the oxidation of chromium and iron in considerable amounts. For the subsequent recovery of chromium and associated iron from the slag, the amounts of metal oxidized must be known for efficient reduction and control of composition. Further, in order to arrive at an accurate understanding of the process, so that chromium-bearing scrap can be used effectively, information is required on the relation between composition of the charge and weight of metal oxidized to reach the desired carbon content. Crafts and Rassbach1 recently developed an empirical relation between chromium, iron, and manganese oxidized per ton of steel charged, and final carbon content and temperature. This relation did not show any dependence on amount of chromium charged. However, it was felt that such a dependence might be present, so a further analysis of the data was undertaken. Cr-C Relation at Low Chromium Levels Crafts and Rassbach's results were based on temperatures estimated from the Cr-C relation previously established experimentally by Hilty,2 and on a single temperature observation (immersion thermocouple) on a heat made at low temperature from a charge of carbon steel scrap containing only a small amount of residual chromium. The temperatures estimated from the Cr-C relation were for heats charged with chromium-bearing scrap and which contained substantial amounts of chromium (2 to 10 pct) at the end of the oxidizing period. No data, other than that from the low temperature heat just mentioned, were available for the low and intermediate chromium ranges. In order to extend the range in which temperature may be estimated, the Cr-C relation requires further consideration. The Cr-C relation, expressed as suggests that carbon is zero at zero chromium in the bath. This is obviously absurd, because as chromium approaches zero the carbon content must approach the limit established by the Fe-C-O equilibrium. It is evident, therefore, that the Cr-C relation as defined by Eq. 1 is not valid below some minimum chromium content that may vary with temperature. On the other hand, it is probable that any such limiting chromium content is less than 4 pct at 3200°F, since the experimental data from which the Cr-C relation was derived included several observations at that level with no deviation. In any event, it is apparent that further evaluation of the results presented by Crafts and Rassbach is dependent upon a means for estimating the Cr-C temperature relation in the low chromium region. From the observations of Chen and Chipman9 and thermodynamic data given in Basic Open Hearth Steelmaking,4 the following relation can be calculated for melts containing small amounts of chromium and carbon assuming a carbon monoxide pressure of 1 atm: % Cr -21,250 K' = (%C)2; logK1 == —t— +13.88 [2] Moreover, by plotting Eq. 2 for any given temperature on cartesian coordinates, it can be extrapolated graphically to the limiting carbon content at zero chromium for the specified temperature without serious complications. By means of Eq. 2 and its extrapolation, the Cr-C temperature relations originally established experi-

Jan 1, 1954

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By Lawrence Addicks

AT the San Francisco meeting of the Institute last year, I presented, through the courtesy of Dr. James Douglas; some results of experiments on the roasting and leaching of concentrator tailings. After it became apparent that flotation rather than leaching was clearly the better method of handling the particular problem under consideration, before dismantling the experimental equipment, some data were secured on roasting and leaching the concentrate itself in competition with smelting. Some of the results obtained are given in the following paper and they a re of particular interest at this time in. view of the large quantities of flotation concentrates with their somewhat difficult smelting characteristics now being produced. A complete wet process? consists of roasting and leaching the calcines in dilute sulphuric acid produced from the roaster gases, roasting the residue with salt and leaching with dilute tower liquors (the well-known Longmaid-Henderson process) and recovering the copper, silver and gold by cementation or electrolysis or a combination of both. It is evident, however, that the residue from the first leaching, carrying about 20 per cent. of the copper and all of the silver and gold, can be smelted if preferable. In considering the application of the scheme to individual cases, it must be remembered that freight plays a. large part in any reduction process wherein smelting is not conducted at the, mouth of the mine, and that it is not practicable today to build small smelting plants for individual operations. The experiments may be grouped under four main heads: Roasting, leaching, chloridizing residue, and recovery of copper from solutions. The products of two concentrators were used: The Nacozari concentrates were the product of a large modern mill not using flotation, the copper mineral being largely chalcopyrite; and the Tyrone concentrates, the product of an experimental mill including flotation, the copper mineral being chiefly chalcocite. Typical analyses would be as follows:

Jan 9, 1916

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942