Search Documents

By D. A. Flanagan, P. B. Crawford

A study has been made of the feasibility of storing liquid meihane at low pressures in undergrohd caverns. Methane liquefies at — 258°F at atmospheric pressure. It is shown that the methane evaporation rates will rapidly decrease and cool the surrounding rock so that at the end of one month they would be between 50 Mcf/hr for a cavern of 25-ft radius and 700 Mcf/hr for a cavern of 100-ft radius. At the end of 10 years, the evaporation rates would be 18 and 100 Mcf/hr, respectively, for caverns of the same radii. The evaporation rates may be reduced by a factor of 2 to 10 by the application of insulation. The cost for mining the caverns is estimated to be $.75 to $1.25/Mcf of storage. This is substantially less than surface storage; it is believed to be safer and to result in lower maintenance, savings in space and savings in strategic materials. INTRODUCTION During the past few years, there has been an increasing interest in the economic feasibility of liquefying methane. Methane liquefaction is being considered for tanker transport; in addition, liquefaction is being reconsidered for shaving peak gas demands. Several articles have described natural gas liquefaction and the progress of the tanker in making trial runs from the United States to Great Britain to determine the feasibility of tanker transport. At the present time, pipelines are not designed to supply peak gas loads during extremely cold periods such as are oiten encountered in the North and Northeast. Gas is being stored in underground reservoirs en-route to its destination, but in many instances satisfactory storage in porous reservoirs has not been practical, especially along the Eastern seaboard where few petroleum reservoirs have been found. In England and other foreign countries, it is unlikely that satisfactory porous structures could be found, and it may be desirable to mine or excavate the rock to obtain storage. By storing the methane near the consumption point, product availability can be increased during periods of need. Methane liquefies at - 258OF at atmospheric pressure, and 1 cu ft of liquid methane will make about 600 cu ft of gaseous methane. Methane liquefaction for shaving peak gas demands was conducted in Cleveland, Ohio in the early 1940's. The Cleveland plant was designed to liquefy 4 MMcf/D of natural gas.' Development of several low-temperature processes has resulted in some improvements in the design of low-temperature storage vessels. Liquefied-methane storage vessels can be designed for various evaporation rates. The desired rate will depend on the reason for liquefaction. For shaving peak gas demands, the desired evaporation rates would be low, possibly between 0.2 and 1.5 per cent/day. For methane tanker transport and supply, the evaporation rates must be high and must equal the total daily rate of supply. It is apparent that the cost of storage facilities will depend on the objective and will vary appreciably. Surface storage of methane may cost between $3,000 and $20,000/MMscf, depending on the size and design. The failure of the surface storage vessels at Cleveland, with the resulting injury and loss of many lives, has caused considerable emphasis to be placed upon developing new, safer and improved methods of storing liquid methane. Storage of liquefied propane and butane in underground salt domes has been very satisfactory. The per-barrel cost of underground storage for any sizeable capacity is very small compared to the cost of surface storage for LPG mixtures. The larger the capacity of the underground storage, the less is the per-barrel cost. Numerous advantages appear to exist if liquefied methane could be satisfactorily stored underground, the principal advantages being increased safety, lower initial cost, lower maintenance cost, savings in space and savings in strategic materials. The purpose of this paper is to determine the feasibility of storing liquid methane underground in mined caverns. If a large spherical cavern is dug underground and is filled instantaneously with liquid methane, the surface of the sphere may approach the liquid methane temperature almost instantaneously. The temperature distribution for a sphere of radius r. in an infinite medium, initially at one temperature with spherical surface kept at T, from time t = 0, is given by Eq. 1.'

By D. W. Hutchinson, W. W. Wen, A. A. Terchick, J. C. Anderson

It is estimated that approximately 3% of the raw coal processed today in coal preparation plants throughout the nation will ultimately report to slurry-tailing disposal (Anderson, 1975). The usual disposal method is to pump refuse slurry containing - 48 mesh (300 pm) refuse into dams or impoundments constructed of coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, WV (Anon., 1972) resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal area. As a consequence of these regulations, the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. US Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition, it was decided to study the stabilization of fine coal refuse slurry through use of cement-type additives. The goal of the investigation is to develop a process that will use cement-type additives to solidify the refuse slurry into a form that can be handled and stacked with the coarse refuse, thus eliminating the need for slurry impoundments.

Jan 1, 1982

By J. W. Axelson, J. N. S. Kwong, J. T. Adams, E. L. Pire, J. F. Johnson

CRUSHING has always been a major operation in the chemical and metallurgical industries, yet little is known about the theory of crushing, and today, the design of crushers is still based almost entirely on empirical knowledge and accumulated practical experience. In view of the increasing national need for the economic working of poorer grades of ores, the lack of a fundamental understanding of this unit operation hardly presents a satisfactory situation. Basic investigations of crushing have been concerned mainly with three phases of the problem, 1—the mechanism of the fracture process itself, 2— the particle size distribution of the crushed product, and 3—the relationship between the energy input and the amount of new surface produced. Probably adequate information on these phases will be required for a comprehensive understanding of the process of crushing. A bibliography covering these phases will be given as well as a review of the work done in recent years at the University of Minnesota on the relationship between the energy input for crushing and the amount of new surface produced. Fracture of Solids This phase of the crushing problem is the most fundamental because it is concerned with the actual mechanism of fracture. The main problems in a study of the fracture process are concerned with the questions of why and how fracture occurs and why there is such a discrepancy between the actual and theoretical energies needed in a fracture process. In considering the how of fracture, Poncelet40 carried Out experiments On the crushing of glass under compression. Actual photographs were taken of the glass plates in various stages of fracture-From these experiments Poncelet was able to postulate a probable mechanism of fracture. Probably because of the quantitative nature of the problem, considerable effort has been expended to find an explanation for the low tensile strength of materials and the conversely high energy for crushing. Tensile strengths are often only 1/500 of the theoretical while the energy for crushing is usually at least 500 times the theoretical. A review of the work to explain the low strength of glass is given by Weyl,52 in which the work of Griffith," Joffe,32 and Powell and Preston " are discussed. In a recent paper Seitz46 holds that the presence of flaws and fissures, as originally expounded by Griffith, is the most probable reason for the low strength of metals. Since a mass of data has been accumulated on the fracture strength of materials, several investigators have attempted to correlate this data in the form of an equation. Glathart and Preston," Taylor,40 Ponce-let,40 Machlin and Norwich," and Frederickson and Eyring,20 have all considered this problem, and the final relationship has always been that the stress for fracture is proportional to the logarithm of time. Murgatroyd30 arrived at a very similar relationship by a different method. The study of the fracture process has used many methods. Among some of these are the thermody-namic approach used by Furth21 which was based on the work of BornxL and later used by Saibel,43 and the statistical method applied by Fisher and Hollo-mon.10 In recent years metallurgists have concerned themselves with the problem of brittle .fracture as opposed to the usual plastic failure of metals. The great amount of interest shown is reflected by the number of contributors to the recent symposium on the fracture of metals.' Repeated failures of welded ships during World War II have accelerated these Studies.31,50,34 The shifting of thought from an emphasis on the

Jan 1, 1952

By Woolsey McA. Johnson

Independently of the recognized chemical reactions involved in the production of metallic zinc, the process is affected by physical conditions in efficiency, and by commercial as well as technical economy. To offer some observations concerning these conditions is the purpose of the present paper. Among the important elements of this problem is the physical nature of the particles constituting the mass of zinc oxide to be reduced. This may be the result, either of the manner of the original deposition of the mineral, or of the treatment to which it has been subjected in the roasting-furnace. The physical character of the reducing-agent is another important factor, since the carbon of some coals is much more active in reduction than that of others. The degree of fineness, whether of ore or coal, or both, likewise plays a significant part. These factors, together with the physical admixture of foreign substances with the ore, may give rise also to chemical " side-reactions," sometimes hindering or retarding, and sometimes accelerating, the reduction. Finally, thermal conditions, including the relative conductivity of the materials, deserve to be taken into account. In firing a furnace with retorts charged with a mixture of roasted ore and coal, the first reaction is naturally the boiling-off of the contained water; the next is the distillation of the light hydrocarbons from the coal; the next is the reduction of the iron oxide to protoxide and sub-oxide successively, and then to metallic sponge; and the final reaction is the reduction of the zinc oxide in the ore by the carbon to metallic zinc. This reaction commences at 1,022o to 1,060o C., according to the physical nature and condition of the coal and ore. Since the retort and the charge are far from being good con-

Jan 1, 1908

By J. E. Hilliard

AS is well-known, the length per unit volume, Lv, of any lineal feature (such as grain edges in a polycrys-talline specimen) can be estimated from a count of the number of point intersections with a random plane of polish. Specifically:' Lv = 2NA in which NA is the expected number of intersections per unit area of the plane. As with all other measurements in quantitative metallography, the estimation of Lv is subject to a sampling error, the magnitude of which will depend on the number of observations. The analysis is usually performed by counting the number of intersections falling within a closed test figure of known area applied to a succession of different areas on the plane of polish. The test figure can be drawn directly on the screen of a projection microscope or else superimposed on the image of the structure by means of a reticule in a focusing eyepiece of an ordinary microscope. The use of micrographs is very inefficient unless, as in the present study, these are also needed for some other purpose. Consider an analysis in which n applications are made of a test figure within which the expected number of intersections is N. The expected total number of intersections counted is then given by NT = nN If (N) is the standard deviation in N for one application of the figure and if the latter is applied to non-overlapping regions so that the N's are independent in the statistical sense, then the standard deviation in Nt is given by: a(NT) = a(N)vn Eliminating n from Eqs. [2] and [3] we obtain: Thus, k will be a constant for a given specimen and test figure. From Eqs. [ I] and [4] we find As is to be expected, therefore, the fractional error in the estimation of Lv is inversely proportional to the square root of the total number of intersections counted. It is very desirable to have at least a rough estimate of k before starting an analysis, since it will then be possible to decide in advance by use of Eq. [5J how many counts should be made in order to achieve the desired accuracy in Lv. Without such information the investigator, unless lucky, will either do needless (and tedious) work or else obtain a result with too large an error. It is very easy to calculate k for the limiting case of N — 0, i.e., when the test figure is vanishingly small. In this case there is a negligible probability of two or more intersections falling within the figure. There are therefore only two possible outcomes: a count of one with a probability of, say, p and a zero count with a probability of (I-p). Thus and Therefore: We might expect k to depend on N and therefore on the size of the test figure. Such a dependence was observed2 in the analogous case involving the estimation of grain-boundary area per unit volume by a count of the number of intersections of a test circle with traces of the boundaries on the plane of polish. In this case the theoretical value of k at the limit N — 0 was 1.41. It was also predicted that k would display an initial sharp decrease with increasing N. Experimentally, k was observed to decrease to a value of 0.62 at N - 6 and thereafter remain approximately constant. Furthermore, the value of k for N > 6 was found to be insensitive to the form of the structure provided no pronounced anisotropy or grain-size variation was present. In order to determinewhether k would exhibit a similar dependence on N in the estimation of grain-

Jan 1, 1967

By S. H. Moll, R. E. Ogilvie

The investigation of solid-state diffusion phenomena may lead to much information concerning binary alloys. In particular, a study of the concentration gradients present in multiphase diffusion couples can lead to the determination of the solubility limits of the single-phase fields in the phase diagram. The specific concentration gradient which results from the heat treatment of a diffusion couple depends not only upon the time and temperature of diffusion, but also upon the number of phases existing in equilibrium at the diffusion temperature. Such concentration gradients possess sharp discontinuities whose terminal points correspond to the solubilities existing at the limits of the two-phase field in the phase diagram at the diffusion temperature. In general, there will be a discontinuity in the concentration curve for each two-phase field which exists in the phase diagram between the concentration limits of the couple. A number of investigators have analyzed the gradients present in multiphase diffusion couples. 1-8 The iron-titanium phase diagram exhibits a y loop in the temperature range from 900" to 1400°C, and the limit of the a + y field lies at some composition which is less than 1 wt pct Ti for any temperature. It was felt that a diffusion study could yield values not only for the diffusion coefficients involved, but also for the chemical solubilities in the phase diagram. The concentration gradients were analyzed by an X-ray absorption technique developed by Ogilvie.6 The absorption of a monochromatic X-ray beam is measured in steps parallel to the diffusion direction and the resulting intensity gradients are transformed into concentration gradients by applying the laws of X-ray absorption in a binary system. This technique has been applied by ogilvie6 to the systems Ni-Au, Cu-Au, Fe-Cr, and Ni-Cr; by Gelles7 to the systems Be-Fe, and Be-Ni and by Hilliarde to the system Al-Zn. Linear X-Ray Absorption Analysis—The use of X-ray absorption analysis as a tool for determining concentration gradients arises from the fact that the beam is absorbed according to the quantity and species of elements present in the sample and not according to their state of aggregation. This method is more advantageous than the chemical analysis of machined layers since it is less time consuming and less expensive and can analyze a very small area. IF a homogeneous binary alloy (A + B) is analyzed with two different monochromatic X-ray beams I0(2) and lo(2) the following relation between the transmitted intensities, the intrinsic absorption coefficients of A and B for the two different radiations and the weight fraction of each element may be derived.' In (I/Io) (a+b) xa(u/p)a(2) + xb(u/p)8(2) Eq. [1] is independent of specimen thickness and density, but requires that either element A or B possess an absorption edge between the wavelength limits of the two monochromatic beams. I, is evaluated for each radiation by measuring the transmitted intensity through a varying number of foils of a suitable absorber. A plot of the natural logarithm of the transmitted intensity as a function of the number of foils, when extrapolated to zero foils, yields the value of I,. If a plot of the ratio in Eq. [ I] is calculated as a function of xA, then a master curve results. From

Jan 1, 1960

By T. A. Rickard

Clement Le Neve Foster was born at Camberwell on March 23, 1841, his father being Peter Le Neve Foster, who was secretary of the Society of Arts for 26 years. As a boy of 12 he was sent to school at Boulogne, receiving a preliminary education there; and in 1857, when only 16 years old, he took his degree of Bachelor of Science from the University of France. In October of the same year he returned to London and entered the Royal School of Mines, which was then in Jermyn Street. He distinguished himself by winning a scholarship and a medal, and by securing his degree as Associate of the Royal School of Mines in the abbreviated period of two years. This was followed by a year at the Bergakademie at Freiberg; subseque1:tly he visited several mining districts in Germany and Hungary. On returning to England, in November, 1860, he received from Sir Roderick Murchison an appointment upon the Geological Survey. During five years he was engaged in field-work, first on the Wealden beds in Kent and Sussex, and then in Derbyshire and Yorkshire. At this time his evenings were largely devoted to reading for a degree from London University. In 1861 he matriculated, obtaining the Bachelor of Science in 1863, with honors in biology and a University scholarship in geology; in 1864 he passed the two examinations entitling him to the Bachelor of Arts degree, and in 1865 he received the degree of Doctor of Science. In 1865 he succeeded Mr. Richard Pearce as lecturer to the Miners' Association of Cornwall and Devon. At the same time he became the curator to the museum of the Royal Geological Society of Cornwall at Penzance, a member of the council in 1873, and a life-member in 1874; he made frequent donations to the museum, besides contributing several valuable papers to

Jan 1, 1905

By J. E. Tiffany

FOR blasting in coal mines the U. S. Bureau of Mines recommends that permissible explosives be used exclusively, that these shall be fired electrically, and that where feasible the working place shall be cut or sheared. These recommendations are made to promote safety and prevent mine explosions. Although permissible explosives are not flameless, their lower flame temperature and shorter duration of flame make their use safer than that of non-permissible explosives. Mixtures of air with both methane and bituminous coal dust, which are liable to occur in coal mines, may be ignited by coming in contact with any type of flame or spark of sufficient temperature and duration or by the firing of a blast. In a working place where a blast is to be fired, in addition to the use of permissible explosives, adequate ventilation for the dilution and removal of accumulations or outbursts of flammable gas should be provided. Bituminous coal mines should be rock-dusted as a means of rendering the coal dust harmless. The efficient use of permissible explosives depends upon the proper preparation of the working place, standardized drilling, the strength characteristics of the explosive, and the use of a proper weight of charge. Experienced shotfirers should load, tamp and fire all holes. The major part of the information and data here presented is based on the results of efficiency tests made in large producing mines of Pennsylvania and Illinois. Bureau of Mines Report of Investigations, Serial No. 2697, describes how a standard method of blasting was worked out and put into operation in a mine in southern Illinois.1 This paper contains a description of the methods worked out subsequently in another mine in that district.

Jan 1, 1928

By C. W. Spencer, F. N. Rhines, R. J. Knight

Ametallographic study has been made of the peritectoid transformation as it occurs in two Ag-A1 alloys, containing 6.0 and 6.9 wt pct Al, respectively. After equilibrating at 475°C, these alloys were transformed isothermally just below the peritectoid temperature which lies at about 450°C.1-3 Peritectoid transformation in this alloy system consists in the reaction of a and 5 to form µ. The crystal structures of the a, µ, and 5 phases have been determined as face-centered-cubic, 6 manganese, and hexagonal-close-packed, respectively. At the peritectoid temperature their equilibrium compositions are approximately 5.85, 7.02, and 7.24 wt pct (19.92, 23.2, and 23.8 atomic pct) aluminum."" The transformation might be expected to occur principally at the interface between the a and 5, but such is not the case. Instead, the major part of the transformation occurs by the direct (and perhaps initially diffusionless) conversion of 5 to µ. The composition range of the forming µ nearly overlaps that of the parent at the temperature of transformation" so that little, if any, composition change is required. Transformation proceeds by the nucleation of µ at points upon the external surface of the sample and sweeps through the 5 phase, leaving the a initially almost undisturbed. Subsequently, the a phase participates in the transformation by being partly or totally converted to µ. Specimens approximately 1/4 x 1/4 x 1/16 in. were cut from cast ingots, previously equilibrated 68 hr at 588°C. The specimens were held for 3 hr at

Jan 1, 1958

By David R. Poirier

Activity data of carbon as a function of both temperature and composition throughout the stable austenite range is correlated by mearts of an equation derived from a quasi-chemical model. The carbon activity data of austmite for temperatures between 800° and 1200°C are utilized in conjunction with the activity of carbon calculated for the y solidus using the activity of carbon in liquid iron and published austenite-liquid equilibria. The results agree very well with Chip-man's correlation; however, a small difference in the activity of carbon in the high-temperature range of the austenite field is evident. Excellent agreement is found for the heat of solution of graphite in infinitely dilute austenite; from this study the value is 10,550 cal as compared with Chipman's value of 10,680 cal. AS part of a program to study microsegregation in dendritic solidification of ternary Fe-C-Cr alloys, it was desirable to be able to describe the equilibria between austenite and liquid iron in Fe-C-Cr alloys. In this regard, it was necessary to correlate existing data on the activity of carbon in Fe-C austenite as a function of both temperature and composition. At that time, Chipman's analysis1 of the thermodynamics of binary Fe-C austenite was not available. It will be shown that this study and Chipman's study agree rather well throughout the stable austenite range of temperature and composition; however, some small differences appear at temperatures greater than the eutectic temperature. Benz and Elliott 2 presented isoactivity lines for austenite superimposed on their revised Fe-C phase diagram. Using an expression from Darken and Gury 3 representing Smith's4 activity data between 800" and 1000°C, they found that the activities extrapolated above 1000°C to the solidus did not agree with the activities determined from the corresponding liquidus compositions. It is the purpose of the following argument to reconcile carbon activity data of austenite with the activity in liquid Fe-C alloys as determined by Rist and Chipman. 5 In addition, a simple analytical expression is sought for computational convenience. ACTIVITY DATA OF CARBON IN ZRON Fig. 1 shows the activity of carbon in Fe-C austenite as determined by Smith, 4 Schenck and Kaiser, 6 Scheil et a1.,7 and Bungardt et al.' The lines are merely drawn to separate the data into the respective isotherms. These data are inadequate to determine the activity of carbon at temperatures greater than 1200°C. The activity coefficient in Fe-C liquid alloys was assumed by Rist and chipmans to obey the following

Jan 1, 1969

By M. A. Meyers, P. P. Meyers

The analysis of the phenomena involved in determining the compressive strength of iron-ore agglomerates leads to the identification of important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compressive axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments u due to internal voids of varying sixes that act as stress-concentration sites. Two novel testing procedures are proposed. The first consults of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents vacant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1984

By F. Keller

ALUMINUM alloys containing magnesium and silicon are susceptible to strengthening and hardening by suitable heat-treatments, and they constitute a class of alloys of considerable commercial importance. Generally, they contain these two elements in the proportions required for the formation of the intermetallic compound Mg2Si, or an excess of silicon; no commercial wrought alloys are made with an appreciable excess of magnesium. The reason for not having excess magnesium is obvious from the results given in this paper, since it is shown that excess magnesium results in a proportional decrease in the solubility of Mg2Si. This is the eighteenth1 of a series of papers from the Aluminum Research Laboratories dealing with the equilibrium relations in aluminum-alloy systems; most of the previous publications concerned binary aluminum-alloy systems; this is the fourth of a group pertaining to ternary aluminum-alloy systems. The work on this system was com-pleted in 1930, but the results were not published because of the pressure of other work. Hanson and Gaylor2, in 1921, presented the results of an extensive investigation of the aluminum-magnesium-silicon system. Their results indicated that an excess of magnesium over the amount required to form the compound Mg2Si caused a noticeable decrease in the solid solubility of Mg2Si in aluminum. A more recent investigation3 in these laboratories showed that the solid solubility of Mg2Si in aluminum was 1.85 per cent at 595° C. and decreased to 0.30 per cent at 300° C. The results of the latter investigation were used as the basis for the present work.

Jan 1, 1936

By G. A. Reinhardt

THE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4 in. (14.5 cm.) square bloom to a ¾ in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900 ° to 950° C. and cooling slowly in mica. The test bars were tempered by heating to 825° to 875° C., quenching in water, and drawing to 515° to 535° C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. ULTIMATE STRENGTH, ELONGATION, LB. PER SQ. IN. PER CENT. IN 4 IN. NOT LESS THAN Annealed specimens 78,230 to 92,450 18 Tempered 120,000 to 149,350 9 After experience oil this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850° to 900° C. and cooling in still air; the annealing, in heating to 850° to 900° C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were:

Jan 7, 1919

By U. K. Custred, E. W. Long, V. R. Degner

In 1973, the United States production of marketable phosphate rock set a record in excess of 42 million tons. This production rate is expected to continue to increase, due to the growing international requirement for fertilizer, at a rate exceeding 5% per year well into 1977. One approach towards increasing plant production capacity to meet the growing demand is through large-capacity flotation cells, provided they achieve metallurgical performance comparable to existing smaller cells. A 9-month evaluation test program recently completed at the Haynsworth mine at Bradley, Fla., demonstrated the feasibility of achieving economically acceptable concentrate grade and recovery levels using large, high-capacity flotation cells. The composition of the feed to the Haynsworth beneficiation plant is a typical Florida pebble phosphate matrix composed of phosphorite pebbles ranging in size from approximately 1-1/2 in. down to 150 mesh and intimately associated with a mixture of clay and sand (essentially silica). The feed contains approximately 22 to 28% phosphate reporting as tricalcium phosphate, Ca3 (PO,) 2, or "bone phosphate of lime" (BPL). The flotation section utilizes the double-float procedure typical of Florida plants. The phosphate is first floated away from the silica in the rougher circuit, using crude fatty acid, ammonia, and fuel oil or kerosene. Rougher conditioning is accomplished at 60 to 70% pulp solids with sufficient ammonia added to raise the pH to 9 to 9.5. Following coarse and fine rougher flotation, the concentrate (overflow) streams are joined and conditioned (sulfuric acid cleaned and washed) prior to entering the cleaner circuit where an amine float (cationic reagent and kerosene added in the feed box; pH 7.3 to 7.8) is employed to float the silica. The feed to the coarse rougher circuit averages 29% +35 mesh while the fine rougher feed averages 10%+35 mesh. Primary attention was directed toward the large rougher cell performance (recovery and grade) on coarse feed during the Haynsworth evaluation program. Flotation Cell Test Program A row of three No. 120 size (300 cu ft) WEMCO flotation cells was installed in parallel with an existing air-cell row. The total installed volume of the large cell circuit was 900 cu ft and required a floor space of 306 sq ft. This compared to the air-cell total volume of 200 cu ft and 152 sq ft floor space. (Both floor areas include feed and tails hoppers but exclude walkways.) Fig. 1 is a schematic cross section of the large flotation cell showing the relative location of key mechanism elements. In operation, the rotor generates a fluid vortex extending up along the walls of the standpipe and creating a sufficient vacuum within its core to ingest air into the standpipe/rotor cavity through the air inlet duct. The ingested air mixes with the pulp, which has been recirculated through the false bottom and draft tube, in the rotor. Further mixing occurs as the air and pulp move radially outward from the rotor, finally passing through the disperser into the flotation cell. Flotation is accomplished outside the disperser, where phosphorite laden air bubbles rise and the remaining pulp recirculates down along the cell wall to the false bottom and draft tube. Large-flotation-cell performance is influenced by the ability of the mechanism to (1) circulate, or suspend, the solids in the pulp; (2) ingest air into the rotor cavity; and (3) mix the air and pulp effectively. The proper balance between pulp circulation and air ingestion is a key consideration in achieving good recovery in a course feed application. Large-flotation-cell pulp circulation and air transfer characteristics are significantly influenced by rotor speed and rotor submergence; therefore, these two operational parameters can be used to "optimize" a particular mill application. Fig. 2 maps the hydraulic performance of the WEMCO No. 120 size flotation cell. This map can be used to relate the cell operational parameters which influence metallurgical performance. At a given rotor speed, power intensity (i.e., pulp circulation) is seen to increase, and airflow decrease, as rotor submergence is increased. The inverse relation between power and airflow is due to the two-phase air-liquid mixture density reduction accompanying the increased airflow rate. For any fixed rotor submergence, the power intensity (i.e., fluid circulation) and airflow both increase as rotor speed is increased. The selection of these two mutually related operating conditions (i.e., rotor speed and submergence) was a key consideration in the Haynsworth evaluation program.

Jan 1, 1976

By F. B. Plummer

PERHAPS the greatest progress made in the technical methods of oil production during the last year has been in handling gas from the new fields that yield light distillate fractions. At least sixteen recycling plants have been perfected and installed in South Texas fields alone during 1939 having a daily capacity of more than one billion -2 cubic feet of gas and capable of producing more than a million gallons of distillate daily. The process consists of running the gas under pres- sure through especially designed plants, separating out the condensate, then compressing the gas to 3000 lb. or more, depending on the subsurface pressure in the formation, and injecting gas back into the reservoir to be produced again later, along with more of the liquid hydrocarbons, and again recycled. Hence production in these distillate fields in sense has changed from that of producing a constantly diminishing and much-wasted product to a more or less continuous manufacturing process, in which practically all the gas is conserved-a real triumph in engineering practice.

Jan 1, 1940

By Leo L. Van Sambeek

An understanding of the creep and yield behavior of salt is required for the rock mechanics design aspects of solution mining. Most previous studies of salt behavior have been performed on small specimens of salt under homogeneous stress conditions; i.e., uniaxial and triaxial tests on specimens <0.002 m3. The corejacking test is a larger scale test (-0.75 m3) with inhomogeneous stress conditions that provides data on the structural response of salt. Interpretation of the responses from eight such corejacking tests provides verification of the requisite constitutive parameters required to predict salt behavior at different levels of stress and temperature. These constitutive parameters are not those studied in the usual laboratory test. Corejacking test results show almost inseparable elastic and plastic closures simultaneous with the corejack pressurization. Very rapid closure (on a relative basis) continues for a period of time after the pressurization. This rapid closure is shown to be both continuing yield deformation and creep deformation. After the period of rapid closure, the closure rate approaches a constant value. Numerical modeling of the corejack tests using a creep law containing both transient and steady-state creep functions does not provide results that agree with the responses measured in the corejack tests. Using an experimental design technique plus additional numerical modeling that includes yielding of the salt, results in identification of the significant parameters which allow agreement. The significance of the results from the study is demonstrated by comparing the postulated stability and creep response of a solution-mined cavern using the previous understanding of salt behavior and the understanding developed from this study.

Jan 1, 1985

By J. B. Clark, A. S. Yue

IN recent years, zone melting1 has been applied extensively to the purification of metals having a very low vapor pressure.2-4 This note describes the zone melting of a high vapor-pressure metal, magnesium, where the melting takes place inside a refractory surface skin. The effects of zone speed and the number of passes of the molten zone on the purification have been determined and the effective distribution coefficients for the principal impurity elements were calculated. A schematic diagram of the zone-melting apparatus is given in Fig. 1. The Vycor tube containing the graphite boat with its magnesium charge (an extruded rod—3/8 in. in diam, 10 in. long) is pulled through the stationary furnaces. A molten zone approximately one-fourth the length of the charge is produced under each of the two central furnaces. Two grades of magnesium were studied—electrolytic magnesium and magnesium with a very low alloy content. The spectrographic analyses of these materials, within * 5 pct of the values stated, are given in Table I. Molten magnesium will vaporize severely if protected only by an inert atmosphere such as argon. Consequently an enveloping container is required. In zone melting, a rigid opaque container surrounding the charge is inconvenient because visual control of the zone length is prevented. A more satisfactory container is a strong flexible skin on the surface of the metal charge which is capable of supporting the molten zone. SO2 reacts with magnesium to form a thin coherent surface film of MgSO, and MgO. An atmosphere of SO, of commercial purity was maintained during the zone melting. Enough oxygen was present within the system and the commercial SO, for the satisfactory formation of the protective skin, so that any rupture of the skin during the zone refining was healed immediately.

Jan 1, 1959

By Orville A. Derby

In view of the recent important discussions before this Institute on the genesis of metalliferous deposits, certain features in the occurrence of gold which seem to be more clearly developed in Brazil than elsewhere can hardly fail to be of interest. As the observations here recorded have necessarily been of a somewhat cursory character, they will be presented in the form of brief notes, without any attempt to draw conclusions as to their genetic significance. Gold in Gneiss.—The statement made by me many years ago† that in the districts of Campanha and S?o Gongalo, in southern Minas Geraes, gold occurs in gneiss, can now be reaffirmed in the most positive manner, on the strength of a recent examination of fresh material, confirmed by the testimony of an experienced mining captain from the Morro Velho mine, who, being skeptical on this point, made a prospectingtour in the district. The specimens examined, though so far decomposed as to be readily disaggregated, were clearly of

Jan 1, 1903

By E. Klar, A. B. Michael

Differences in the electrical conductivities of copper powder sintered under reducing, selectively oxidizing, and neutral atmospheres are related to impurities in solution or as precipitated oxides. The precipitation of impurities as oxides during sintering in nitrogen is proposed for maximizing the conductivity of sintered copper. Conductivity equations for two-phase systems are summarized. Selected equations are applied to porous sintered copper and composite structures. A recent review of the influence of impurities on the electrical conductivity of copper by Gregory et al.1 emphasized that an impurity in solid solution has a much more pronounced effect on reducing the electrical conductivity than when present partly or wholly as a second phase. When impurities in solid solution can be precipitated as oxides, the copper is purified with respect to these elements and the conductivity is increased. Cast and wrought copper, therefore, frequently contain an intentional residual oxygen concentration to oxidize and precipitate impurities less noble than copper. Copper powders generally also contain impurities which can contribute to a reduction in the electrical conductivity of the sintered material. The most deleterious impurities commonly found in commercial copper powders which markedly decrease the electrical conductivity when in solid solution but which can be precipitated as oxides include iron, tin, antimony, arsenic, cobalt, and nickel. In addition to impurities, porosity in sintered copper also contributes to a reduction in the electrical conductivity. The work reported herein discusses the influence of impurities, sintering atmospheres, and porosity on the electrical conductivity of sintered copper. These are important factors for controlling the electrical conductivity of materials such as sintered copper electrical contacts. Several publications on the electrical conductivity of sintered copper and composite materials with random pores or obstacles have incorrectly considered the conductivity to be proportional to the volume fraction of conducting material. However, analyses and equations have been proposed, the earliest of which is perhaps Lord Raleigh&apos;s of 1892,&apos; which more accurately describe the conductivity of two-phase systems. These equations which in many cases allow one to closely estimate the electrical conductivity of porous sintered materials and two-phase composites will be reviewed and related to the measured electrical conductivity of sintered copper, copper-graphite. and Ag-W composites. INFLUENCE OF IMPURITIES AND OXIDIZING, REDUCING, AND NEUTRAL ATMOSPHERES Zone-Melted and Leveled Copper. The electrical conductivities of an electrolytic copper and a lower-purity compacting grade of copper powder after consecutive treatments in reducing or selectively oxidizing atmospheres are compared in Fig. 1. The powder and drillings from the electrolytic copper ingot were melted and solidified in a graphite crucible under hydrogen. The vertical zone leveling technique of multiple passes in opposite directions was used to obtain a uniform distribution of impurities. The electrical conductivity was measured on machined specimens 3 by 0.10 in. diam of the zone-leveled material and after the same specimens were consecutively treated as follows: 1) heating in hydrogen at 1600°F for 3 hr; 2) heating in air in a sealed tube so that 0.04 pct 0 was introduced; heating was started at 1000°F for 1 hr and continued at 1800°F for 8 hr; the stepwise diffusion treatment was used to avoid loss of copper due to evaporation of copper oxide at higher temperatures; and 3) final heating in hydrogen at 1600°F for 3 hr. A L&N Kelvin Bridge, type 4306, and a test fixture with knife edges 2 in. apart were used to measure the room-temperature conductivity with an estimated accuracy of ±0.5 pct. In all cases the conductivity of the electrolytic copper was approximately 100 pct of IACS. The conductivity of the impure copper was 80 pct of IACS both in the cast state and after heating in hydrogen. However, after the heating in air, the conductivity of the impure material was 100 pct IACS. After again heating in hydrogen, the electrical conductivity decreased to 60 pct of IACS. This decrease is attributed both to the dissolution of impurities and observed intergranular cracks due to the phenomenon of hydrogen embrittle-ment in copper. These data show that the electrical conductivity of commercial copper as represented by a compacting type powder can be increased significantly by the precipitation of impurities as oxides through heat treatment in an oxidizing atmosphere. Sintered Copper Powder. A commercial compacting type of copper powder pressed to various densities was sintered either in nitrogen, dissociated ammonia, or dissociated ammonia followed by a selectively oxidizing atmosphere of air in sealed Vycor tubes so that 0.06 pct O was added to the material. The electrical conductivity was measured perpendicular to the pressing direction on as-sintered specimens of approximately 3 by 0.25 by 0.15 in. The fully dense material was obtained by zone melting and leveling

Jan 1, 1969

By R. S. Dean

BLUE HEAT PHENOMENA IN constructing a theory of the flow and hardening of metals, we necessarily make use of such phenomena as seem to be, universally observed in metals. It is, therefore, a matter of. concern to the constructors of such mnemonic systems if one or two of the group classified as metals show anomalous behavior. Such egregious phenomena are observed in pure or nearly-pure iron in the reaction of its mechanical properties to low-temperature annealing after cold work and to increased temperature of testing. In short it has been generally observed that iron," as an outstanding exception among metals, increases its hardness and strength by low-temperature annealing. after cold work,1 and also by increase of testing temperature to the range of 150° to 300° C. The investigation here recorded was made then with the object of ascertaining if similar phenomena were observed in high purity iron and, if not, to the presence of which impurities these phenomena could be traced.

Jan 1, 1929