Search Documents

By Wilhelm Rohn

IN discussing the influence of a content of gases on metals and alloys we should probably first consider the physical and chemical conditions under which these gases may be present. By a chemical analysis, such as the total extraction of gases from the liquid metal by melting in a graphite crucible in vacuo, we find only the sum of gaseous chemical elements contained in the metal in any form and no reference is made to the special form under which they have been present previously. CONDITION OF GASES IN METALS In considering. gases in metals we may first turn our attention to gases simply dissolved. Because the solubility of almost, any gas decreases suddenly at the freezing point, most of them are released during solidification, developing rise of ingots and blowholes. If only a little gas is dissolved in the molten metal the size of such blowholes may be miscroscopical, or even submicroscopical, resulting in, a certain reduction of the notched-bar impact test values. Hydrogen is believed to become less soluble as the temperature is lowered and therefore increasing quantities of this gas may be evolved during cooling between the freezing point and room temperature, leading to unsoundness of the ingot at weak spots; i.e., at the grain boundaries. This gas at the grain boundaries probably is present at high pressure and therefore impairs the mechanical properties to a degree similar to that found in the hydrogen embrittlement of copper. Usually we may trace such gases by observing rising ingots, or at least by the formation of a characteristic pattern of small grooves upon etching. Another condition of gases present within metals is that of chemical compounds, the most common being oxides and mostly present as slag inclusions of various kinds. If such oxides are insoluble in the liquid metal and emulsify with it, we find microscopical or submicroscopical slag inclusions distributed homogeneously throughout the metal and spread through the whole mass of the crystals. This special form does little harm to the mechanical properties. Some oxides are somewhat soluble

Jan 1, 1932

By Graham Swan, Ove Alm

In-situ fracture toughness experiments have been performed with a scanning electron-microscope. The rock, Stripa granite, was loaded both in tension and three-point bending using the same size notched plates. Observations, which included crack extension measurements as a function of load, are presented in the form of R-curves. The data does not sup- port the proposition that R-curves can be regarded as independent of specimen configuration for this granite. Typically crack extension was seen to begin at loads of 70-80 % failure load. Tensile specimens showed considerably greater sub-critical crack growth than the bend specimens. Evaluation of the approximate fracture toughness Km for both specimen types produced as expected erroneously low estimates Of KIC, being worst in the case of the tensile specimen. Some crack extension data for Stripa granite using the indirect methods of compliance calibration, fluorescent dye penetrant and acoustic emission are compared. In a material such as Stripa granite it is considered that no single method is without its limitations.

Jan 1, 1982

By Wells A. Hutchins

Water laws important to the mining industry are those which govern or affect the right to use water, to dispose of water after using it in mining or milling, and to discharge waste material into water-courses. They include statutes and court decisions having general applicability, as well as others that pertain specifically to mining. THE INDUSTRY'S CONTRIBUTION TO WESTERN WATER LAW Despite sharp differences of opinion, the water law the Spaniards brought to the Southwest appears to have included some form of appropriation of water. The Mormons, who settled in Utah in the mid-nineteenth century, also developed a system of appropriative water titles. But by far the most profound impact on western water law was made by the gold- seekers who flocked to the Sierra Nevada foothills of California after the discovery of gold in 1848. Much of the gold was extracted from the ground by hydraulic or placer mining, and so the-miners' rights to the use of water became fundamentally important. Since there was no organized government in the foothills and no laws other than those made by the miners, they helped themselves to the land, the gold, and the water needed to work their claims.' They established and enforced regulations governing the acquirement and holding of mining claims and their rights to the water they needed.'In 1879 Justice Field, former Chief Justice of the California Supreme Court, spoke for the U. S. Supreme Court in saying that the miners were "emphatically the law-makers, as respects mining, upon the public lands in the State.""

Jan 2, 1960

By C. V. Millikan

Temperature measurement in wells is an old practice and geothermal gradients have been of interest to geologists for many years.le2 Their application to the operation of oil wells is a more recent practice. It has long been recognized that temperature anomalies occur in drilling and producing wells but thermometers that could obtain a satisfactory record of the anomalies were not available. The normal geothermal gradient is con-sidered as being about one degree Fahren-heit for each 60 ft. of depth.4 This "nor-mal " gradient varies in different areas, but whatever it may be in an area there is little variation from the surface to as deep as the : drill penetrates. The normal gradient is appreciably changed by gas expanding ; from the reservoir into the borehole or by the movement of fluid through a borehole : while drilling, producing, or circulating. It is the resulting anomalies and abnormal gradients from which conditions in wells can be interpreted. Some of the applications of such interpretations are locating the position of oil or gas sands, permeable strata in a reservoir zone, gas-oil contact, source of water, casing leaks, and the top of cement behind casing. Thermometers A thermometer for use in wells must be sensitive and have a low thermal lag. The sensitivity should permit recording 0.2OF. or less for differential temperatures although the actual temperature need not be more accurate than 1°F. The thermal lag should be as low as rugged construction will permit in order to allow surveys to be made in a minimum of time. Of the several kinds of thermometers, these requirements are most easily obtained with the vapor-pressure, expansion, and electric-resistance types. Thermometers for use in wells may be self-contained—that is, the complete instrument is lowered into the well and a record made of the temperature—or the thermal element only may be lowered into the well and the temperature recorded at the surface. The vapor-pressure and expansion types are more adaptable for a self-contained instrument while the electric-resistance thermometer is more suitable for surface recording of temperatures. The self-contained instrument can be run against high pressure on a single wire line with only one operator required. The instrument and its hoisting equipment is easily portable and can be mounted on a small car. The disadvantages are a somewhat greater thermal lag and the necessity of completing a run before any temperature or temperature anomaly is known. A surface-recording thermometer has the advantage of being somewhat more sensitive and of having a lower thermal lag. The Operator can see what anomalies are encountered and can immediately change the running conditions of the instrument or the well conditions in order to obtain the most

Jan 1, 1941

By C. V. Millikan

Temperature measurement in wells is an old practice and geothermal gradients have been of interest to geologists for many years.le2 Their application to the operation of oil wells is a more recent practice. It has long been recognized that temperature anomalies occur in drilling and producing wells but thermometers that could obtain a satisfactory record of the anomalies were not available. The normal geothermal gradient is con-sidered as being about one degree Fahren-heit for each 60 ft. of depth.4 This "nor-mal " gradient varies in different areas, but whatever it may be in an area there is little variation from the surface to as deep as the : drill penetrates. The normal gradient is appreciably changed by gas expanding ; from the reservoir into the borehole or by the movement of fluid through a borehole : while drilling, producing, or circulating. It is the resulting anomalies and abnormal gradients from which conditions in wells can be interpreted. Some of the applications of such interpretations are locating the position of oil or gas sands, permeable strata in a reservoir zone, gas-oil contact, source of water, casing leaks, and the top of cement behind casing. Thermometers A thermometer for use in wells must be sensitive and have a low thermal lag. The sensitivity should permit recording 0.2OF. or less for differential temperatures although the actual temperature need not be more accurate than 1°F. The thermal lag should be as low as rugged construction will permit in order to allow surveys to be made in a minimum of time. Of the several kinds of thermometers, these requirements are most easily obtained with the vapor-pressure, expansion, and electric-resistance types. Thermometers for use in wells may be self-contained—that is, the complete instrument is lowered into the well and a record made of the temperature—or the thermal element only may be lowered into the well and the temperature recorded at the surface. The vapor-pressure and expansion types are more adaptable for a self-contained instrument while the electric-resistance thermometer is more suitable for surface recording of temperatures. The self-contained instrument can be run against high pressure on a single wire line with only one operator required. The instrument and its hoisting equipment is easily portable and can be mounted on a small car. The disadvantages are a somewhat greater thermal lag and the necessity of completing a run before any temperature or temperature anomaly is known. A surface-recording thermometer has the advantage of being somewhat more sensitive and of having a lower thermal lag. The Operator can see what anomalies are encountered and can immediately change the running conditions of the instrument or the well conditions in order to obtain the most

Jan 1, 1941

By A. G. Allten

EXAMINATION by metallographic and X-ray diffraction means of an austenitic steel containing 0.06 pct C, 1.26 pct Mn, 0.38 pct Si, 21.15 pct Ni, 18.72 pct Cr, 3.07 pet W, and 9.14 pet Mo indicated that a - phase, which had not been reported in the literature, existed in this steel. Both the s and car-bides of the M6 C type were present in the as-forged steel. The carbides dissolved completely in the aus-tenite at approximately 2200°F (1205°C). The s, however, was present at all temperatures up to the solidus temperature of the steel at approximately 2375°F (1300°C). Ferrite was not found in any condition of the steel. The faintness of some of the s lines in X-ray patterns obtained from samples of the steel made it desirable to isolate the s prior to verification of its entire pattern. It was found that the s phase could be separated from samples of the steel which had been water quenched from 2250°F (1230°C) by dis-

Jan 1, 1955

By Zay Jeffries

The object of the present paper is to enlarge somewhat on the general principles advanced in my discussion1 of Mathewson and Phillips' article on The Recrystallization of Cold-Worked Alpha Brass on Anneal-- ing.2 It will also serve as an acknowledgment of Prof. Howe's most important remarks on my contribution. In this paper the writer has adopted Prof. Howe's suggestion to substitute the term "germinative temperature'' for "critical temperature for grain growth." Instead of being an exact or certain temperature it should be considered that the germinative temperature phenomenon exists throughout a small temperature range. v Factors Influencing Fast Growth Phenomena The development of grains of macroscopic size at the germinative temperature should be considered the extreme condition of a general rule. When considered in this light it is not strange that the development of these large grains should be the exception and not the rule. The principal factors influencing the operation of the laws of fast growth temperature are as follows: . 1. Rate of heating. In the original paper,' the germinative temperature was defined as "the minimum temperature at which two adjacent grains can coalesce to form one larger grain, provided that this larger grain will have sufficiently increased its power of attack, to enable it to absorb adjacent grains which cannot coalesce with each other. Time is always to be understood as a factor governing the first stage of grain growth." If the time of heating is short, the germinative temperature is raised. The formation of large grains in metals may occur at relatively high temperatures when the rate of heating is rapid. It is to be understood that in such cases, grain growth

Jan 1, 1917

By G. A. Alers, F. Borik

Rolled sheet products are elastically anisotropic and a large number of measurements of Young's modulus and rigidity modulus are necessary to completely specify their elastic properties. This paper describes and uses a simple measurement technique to obtain the nine elements of the elastic modulus tensor from which all the elastic The elastic properties of a polycrystalline material are usually specified by giving the Young's modulus E and the rigidity modulus G. Unfortunately, these two moduli by themselves are insufficient to completely specify the elastic properties because the rolling process introduces a preferred orientation which makes the material properties can be deduced. In particular, the variation of Young's modulus and the rigidity modulus in the principal planes of a sheet of ausformed steel were deduced. Furthermore, the variation of Young's modulus in the rolling plane was compared with direct measurements. anisotropic. This anisotropy makes E and G functions of the orientation of the test specimen in the sheet so that a complete description of the elasticity requires many measurements on a large number of specimens. A more fundamental approach to the problem is to consider the sheet as a single crystal and measure the elements of its elastic modulus tensor. Although this appears formidable, there have been developed recently high-frequency ultrasonic techniques which yield these tensor elements directly. The symmetry of a rolled sheet is such that it behaves elastically as if it were an orthorhombic

Jan 1, 1965

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel'd and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By T. Federighi, S. Ceresara, C. Panseri

The results of an exploratory investigation by means of resistivity measurements at -195ºC, on the aging characteristics of a set of Al-Mg alloys with a maximum content of 7 pct Mg, are reported. Whereas for dilute alloys (Mg < 1.5 pct) only a decrease in resistivity is observed at about 100°C (due to the elimination of quenched-in vacancies), for more concentrated alloys such a decrease is preceded by an increase in resistivity in the range between -60ºand +40°C. Following some previous suggestions, this increase is considered as good evidence for clustering of solute atoms @reprecipi-tation process). From the analysis of the results it appears that, although the process is substantially similar to that observed in other Al-rich alloys, it is characterized by a strong interaction between vacancies and zones. THE process of formation of Guinier-Preston zones, i.e., preprecipitation,1&apos;2 which occurs during the aging at about room temperature in many supersaturated aluminum-rich alloys, has been extensively investigated in the past few years by several workers.2,3 owever, a very interesting question arises when the case of Al-Mg alloys is considered: although it is very easy to supersaturate Al-Mg alloys, just in the same way as for many other aluminum alloys showing preprecipitation, only very little experimental evidence was available until a short time ago in the literature supporting the existence of "natural" aging in supersaturated Al-Mg alloys (see, for example, Refs. 4 to 6). On the other hand, as is well known, the X-ray method is not useful in this case because the X-ray scattering factors of magnesium and aluminum atoms are about the same. Recently, however, Cordier and Detert7 have stressed that during the aging at about room temperature of a supersaturated Al-Mg 10 pct alloy it is possible to detect an increase in resistivity; since, as is well known, such an increase is observed also in most alloys showing preprecipitation, the above authors have interpreted their results as evidence for the formation of magnesium-rich clusters (or Guinier-Preston zones) during the aging. In the course of or ientative investigations on preprecipitation in several aluminum-rich alloys, we also could detect a similar phenomenon in more dilute Al-Mg alloys, see Instituto Sperimentale Metalli Leggeri, Annual Report, 1959, and also Ref. 8. Since the details of our observations, although of a preliminary nature, differ from those of Cordier and Detert and allow one to draw a more advanced picture of the preprecipitation process in Al-Mg alloys, we have thought it useful to report our results in this paper and to comment on them briefly.

Jan 1, 1963

By S. Webster, M. Karmis, C. Haycocks

Mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. The effect is often detrimental to the recovery, cost and safety of mining the subsequent seams. This paper describes the ground control mechanisms involved in mining through a passive subsided zone or all actively subsiding trough. Data were extracted from case studies, primarily from the Appalachia region, for construction of empirical models to predict interaction problems that can occur in overlying seams. Inner-burden thickness, innerburden lithology, percentage extraction, lower seam height, time and overburden were analyzed to determine their effect on upper seam damage. Magnitude of upper seam subsidence was incorporated, together with a broad classification of rock types, to predict the type and range of damage that can occur in the upper seam. Results are summarized in graphically and nomogram form for use in. engineering design.

Jan 1, 1984

By Kalervo Rankama

UNTIL a few years ago, geological mapping, the study of ore boulders, and different geophysical methods were the principal means used in the systematic search for mineral deposits covered by a layer of disintegration products or soil. These methods have been developed to a high stage of perfection as far as the geometrical definition of the conductor is considered. Use of geophysical methods in prospecting is based on the fact that an ore body differs from the country rock not only geologically but also in its physical properties. The general drawbacks and complications included in the use of geophysical methods are well known to everyone who has been using them, so need not be entered into here in detail. One of the more important ones is the fact that geophysical methods are unable to furnish information concerning the chemical composition of the ore bodies responsible for the indications. Further, the ores of many metals, such as silver, gold, beryllium, zinc, mercury, tin, lead, vanadium, antimony, chromium. molybdenum, tungsten, manganese, cobalt, nickel, and the platinum metals cannot be directly located by known geophysical methods, owing to lack of physical characteristics suitable for distinguishing them from the country rock. Thus it is quite natural that efforts have been made to develop direct methods for prospecting and locating ore bodies of the elements named. Known as chemical, biogeo-chemical, and geobotanical methods of prospecting, these have been much improved during recent years. A brief review of these methods and of some results obtained with them will be presented in the following, on the basis of available information and my own experience.

Jan 1, 1947

By C. H. Jr. Herty

IRON oxide .(Fe0) plays an extremely important part in the manufacture of steel. In the open-hearth furnace and the Bessemer converter it is the chemically predominant compound and controls to a large extent both the operation of the furnaces and the composition and quality of their products. Almost all of the refining action is carried out through the medium of FeO, which oxidizes carbon, manganese, silicon, and phosphorus. At the end of any open-hearth or Bessemer heat the steel contains dissolved iron oxide, which must be wholly or partly eliminated. The type of deoxidation product depends on the amount of dissolved iron oxide and on the deoxidizer used. After the heat has been deoxidized and while it is being teemed, iron oxide diffuses from the ladle slag into the metal, causing losses of deoxidizer and increase in iron oxide content of the steel. It is generally believed that non-metallic inclusions are responsible for a great many failures of steel in service and for decreased yield of steel during rolling. The basis of most non-metallic inclusions is dissolved iron oxide. This investigation was undertaken in order to determine the amount of iron oxide that will dissolve in iron under various conditions. Steel-making slags are complex and it has been thought best to determine solubility under simple slags as a first step. The study is being continued under slags whose compositions approach those of operating. slags.

Jan 1, 1928

By Arthur W. Gray

The thermal analysis of a metal or an alloy is ordinarily made with the aid of heating and cooling curves in which transitions are indicated by the rapid changes in curvature that accompany changes in the rate of heat absorption or evolution. Analysis by the method that depends on the change in thermal expansivity is not customary, partly, at least, because of the difficulties involved in making the necessary measurements. However, under certain circumstances, the dilatometric method of analysis may possess advantages over the thermometric method that will justify the additional trouble required. The addition of 1 per cent. of zinc to an alloy has been found to produce upon the volume changes that take place during transition effects that suggest the possibility of using the dilatometric method of thermal analysis as a rather sensitive means of obtaining chemical information. Although the illustrations presented in this paper are drawn from data obtained during an investigation of dental amalgams, similar phenomena can doubtless be observed with other alloys. Some of the results found during an investigation made in 1917l have been confirmed by data on the thermal expansivity of amalgams published by Souder and Peters of the Bureau of Standards in reporting tests of dental materials.2 Although the Bureau of Standards made experiments for the purpose of discovering effects of including zinc as one of the constituents of a dental alloy—a matter much discussed in dental literature but without the presentation of reliable experimental evidencae to support the views of either side—the reports of the tests made by the Bureau give the impression that certain striking phenomena associated with the presence of zinc were not noticed. Among such phenomena arc those connceted with the conditions that determine whether or riot a specimen of amalgam becomes covered with droplets from which crystals develop.

Jan 1, 1921

By B. M. Larsen

IN spite of the great amount of operating experience and of studies directed toward elucidation of the interrelation of the several processes going on in the blast furnace, the present picture of its operation is based largely on indirect evidence and on speculation. The reason for this unsatisfactory situation is the extreme difficulty of making direct observations and significant measurements while the furnace is operating, and of translating laboratory experience to the conditions obtaining in the smelting process. Yet there are questions that can be investigated with some promise of a definitive answer; and it is the purpose of the present paper to set forth some of these questions, as a basis for discussion, which may, it is hoped, lead to active work on some of them. In order to provide a starting point for this discussion, some views held tentatively by the writer are outlined, along with a certain amount of evidence gathered from operating records and interpreted on the basis of the ideas expressed. These opinions may prove not to be pertinent, and may well not be in accord with the opinions of others; they have been included to encourage others to do likewise and on purpose to provoke informal discussion. In this way it should be possible to transcend the limitations of formal papers; to bring forth suggestions of new hypotheses or new methods of investigation; and to promote better understanding between investigators and operators in this difficult field. The statements made express the present views of one physical chemist who is not too familiar with all the difficulties of maintaining these enormous reaction vessels in reasonably smooth and economical operation; who, however, is persuaded that some of these difficulties would be less formidable if surer knowledge of the several interrelated and concurrent processes were available and made use of. For these difficulties arise largely, it is believed, from variation in conditions which the operator must meet as best be can, and should lessen as these conditions can be brought under control so that they are either made substantially constant or the variations are neutralized by compensating methods. A. VARIATION IN BURDEN AND IN MIXING OF CHARGE To the scientific investigator, who aims to control the conditions of experiment and to limit the number of variable factors, the most perplexing aspect of the blast-furnace process is that nothing seems to remain constant for long. Variations of burden seem to be unnecessarily frequent; and, even if the charge were constant from hour to hour, its constituents usually are not mixed as intimately as they might well be. It is understandable that separate layers of coke and of ore, also separate layers according to size, promote permeability and the

Jan 1, 1947

By P. E. Doherty, B. Chalmers

Subboundaries may be revealed in aluminum by the formation of pits on the surface during cooling from elevated temperatures. The pits do not form in the vicinity of high- or low-angle boundaries. They are attributed to the condensation of vacancies from a super saturation produced during coolirzg. Using the vacancy pit and Schulz X-ray techniques for observing low-angle boundaries, a study was made of the transition from the nearly perfect seed to the striated structuke characterist-ic of aluminum crystals grown from the melt. It was found that the individual striation boundaries develop by the coalescence of very small-angle boundaries, as well as by the addition of individual dislocations. Several mechanisms for the formation of striations are discussed. Evidence was found suggesting that a super-saturation of vacancies exists near a growing interface, and it is proposed that the resulting climb of existing dislocalions produces "half&apos;-loops" at the interface, which combine to form the low-angle striation boundaries. LINEAGE, or "striation" boundaries, have been studied in detail by Teghtsoonian and Chalmers 1,2 in crystals of tin grown from the melt, and by Atwater and Chalmers3 in lead. They found that single crystals grown from the melt consist of regions which are separated by subboundaries that lie roughly parallel to the growth direction. A difference in orientation of 0.5 to 3 deg exists between the striated regions; the misorientation is such that the lattice of one region could be brought into coincidence with the lattice of its neighbor by a rotation about an axis approximately parallel to the direction of growth of the crystal. They observed an incubation distance for the formation of striations which increased with decreasing growth rate. They also found that in any crystal, the sum of all rotations of the lattice in one sense, in going from one striation to the next, is very nearly equal to the sum of all the rotations in the opposite sense. A striation boundary, which is a low-angle grain boundary, can be described as an array of dislocations. If it is assumed that suitable dislocations are introduced into the crystal during solidification, the formation of striation boundaries can be explained as a result of the migration of the disloca- tions into arrays. The formation of arrays is energetically favorable since the energy of an assembly of dislocations can be reduced by the interaction of the stress fields when a suitable array is formed. This investigation presents and interprets new information concerning the nature and origin of striation boundaries in aluminum. EXPERIMENTAL TECHNIQUE Single crystals of high-purity aluminum (Alcoa 99.992 pct) were prepared by horizontal growth from the melt.&apos;&apos; The specimens were subsequently electropolished in a solution of 5 parts methanol to 1 part perchloric acid kept between -10° and 0°C in a bath of dry ice and alcohol. The current density was approximately 6 amps per sq in. Doherty and Davis9 have shown that in aluminum sub-boundaries with misorientations of not less than several seconds of arc may be revealed by the vacancy pit technique. During cooling from elevated temperatures pits form on electropolished surfaces of aluminum crystals as a result of the condensation of vacancies.11 Pits do not form in the vicinity of small- or large-angle grain boundaries, presumably because such boundaries act as sinks for vacancies. Boundaries of misorientations down to 3 sec of arc are revealed as pit-free regions, see Fig. 1. The Schulz X-ray technique12 was used to determine the angular misorientations of subboundaries. In this method, white radiation from a micro-focus X-ray tube is used to produce an image of a fairly large area of a single crystal surface. Subboundaries cause splitting in the diffracted image, see Fig. 2. Misorientations down to about 15 sec of arc may be observed with this technique. OBSERVATIONS AND DISCUSSION Figure 1 shows a striated aluminum crystal grown at 10 cm per hr etched by the vacancy pit technique. An incubation distance of about 1 cm is observed before the initiation of striation boundaries. Fig. 2 is a Schulz X-ray photograph of a striated crystal similar to that shown in Fig. 1. A large area of the crystal was studied by means of a series of photographs. Fig. 2, which is a reflection from the (100) plane, included about the first 4 cm of crystal to freeze. There is an incubation distance of about 1 cm, and a distance of about 2 cm over which the angle of misorientation builds up to its final value of approximately one degree. Some twist component can be seen in Fig. 2 at the right side of the photograph. From Fig. 2 it can be seen that the sum of all rotations of the lattice in one

Jan 1, 1962

By K. S. Lane

As the initial chapter in this section entitled "Role of Fluid Pressure in Rock," this attempts to fulfill an assignment for (1) summarizing the state-of-the-art and (2) illustrating engineering problems resulting from rock pore pressure. Hence, the chapter is presented in two parts: 1) Basic Concepts, and 2) Examples of Engineering Problems, including failures. Neither of these objectives has necessarily been completely met: partly from limitation of space and partly as the case histories have been restricted to the author&apos;s own field in civil engineering, and there deemphasizing those applications which will be covered in more detail by subsequent papers in this section. As with any state-of-the-art attempt, contributions of some have undoubtedly been overlooked (or omitted for brevity). Notwithstanding the foregoing limitations, it is hoped that this summary of the situation will at least: 1) Outline current concepts on effects of fluid pressure in rock-both as a pore pressure in interconnected void spaces of the intact rock and as a cleft pressure or hydraulic force acting in the joints or other discontinuities of the rock mass. 2) Indicate the often fragmentary nature of evidence presently available to support these concepts and thus encourage further research. 3) Illustrate the major significance of fluid pressure in several types of engineering problems and thus stimulate its consideration as designers encounter related situations.

Jan 1, 1970

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.&apos;8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By W. E. Foreman, James A. Redding

INTRODUCTION Screening is a mechanical process that separates particles by size. Modern coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modern preparation plants is done for the following reasons: 1 ) Removal of fine coal before a size reduction step. 2) Size separation of the coal into a coarse and fine fraction for sized products or processing in coarse and fine coal circuits. 3) Recovery of heavy media from heavy media coal cleaning circuits. 4) Dewatering. 5) Rock and trash removal by handpicking on a screen. Fig. 8-1 is a generalized flowsheet of a plant showing the use of screens in the coal preparation process. Table 8-1 shows the vibrating screen equipment utilized in Fig. 8-1

Jan 1, 1979

By Edwin A. Sperry

In 1892 I tested an ore, which was peculiarly difficult to treat, on several concentrators then in general use, including t,he Frue-vanner, the Luhrig table and the Cornish buddle. Owing to the character of the ore it had to be crushed- to a very fine state of division, and the results obtained were far from satisfactory; a large proportion of the values was lost in the slimes, which indicated the necessity of a very careful sizing before dressing. Even after reworking some of the slime-tailings, the results, in my opinion, were not as good aa those which might be obtained on a table designed more especially for the handling of slime. Although the subject of slime-concentration has occupied the attention of many engineers who have threshed the field quite thoroughly, the results obtained in my work led to a careful

Jan 1, 1904