Search Documents

By J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and ferric iron concentration. The results have been discussed in terms of the adsorption of ferric cations and ferric hydroxide to the quartz surface. Possible relationships between the experimental results and the flotation of quartz have been examined. The adsorption of multivalent cations at the surface of quartz has been studied by many investigators who have used a variety of experimental techniques ranging from streaming potential 1 to radiometric2 measurements. Two possible mechanisms of cation activation of quartz have emerged from the results of these investigations viz: the adsorption of the cation to the negatively charged quartz surface, followed by adsorption of the collector anion to the adsorbed cation site, or: formation of a cation-collector complex which is then adsorbed to the quartz surface. In many natural and industrial systems one of the most prevalent activating species for quartz is ferric iron, this is especially so in the acid-circuit, anionic flotation of iron ore. The adsorption of ferric iron to the quartz surface is complicated by the ability of ferric iron to form complexes with anions, a phenomena which is of minor importance in one of the most widely studied quartz activation processes, ca ++ activation.* *The pK value for [ca(oH)+]/ [ca2+] [oh-] is 1.46 indicating that the influence of Ca (OH)+ ions will be minor in all but strongly alkaline solutions. In order to obtain a better understanding of quartz activation by ferric iron the zeta potential of quartz in the presence of ferric iron has been measured over a range of pH and ferric iron concentration. EXPERIMENTAL METHODS Materials: Selected samples of "rock clystal" quartz from New England, N.S.W., were ground in a pebble mill, washed for three hours in boiling concentrated hydrochloric acid, washed in hot chromic acid and then washed repeatedly with distilled water until the washing water gave no trace of chloride ion.

Jan 1, 1967

SAMUEL L. HOYT,* Minneapolis, Minn. -I was privileged to see the apparatus used by Mr. Scott, which is quite unique. It is, as the author says, a modification of the apparatus designed by Dr. Rosenhain, but it is evidently quite an; improvement. The author is to be congratulated on the fact that lie has given us, with his apparatus, a quantitative thermal analysis of these critical points. I notice the author refers to Ac3, Ac2, and Ac1. His designation of the Ac2 point is all right, but naturally in a steel with as much carbon as this, which would mean a hypereutectic steel, the other point might better be considered as an Ac, point with possibly another point above the Ac, point. Another important point brought out is the fact that, in Fig. 3, the lines representing the Ar1, transformation and the Ac,1_3 transformation do not intersect at the zero rate curve,

Jan 5, 1919

By Donald Barton

THIS paper outlines a time-saving graphical method of calculation for application to the interpretation of observations with the Eötvös torsion balance. Preliminary to the treatment of this short cut method which has been found practicable, the principal formu-las by which the student of interpretation can calculate the gradient and differential curvature produced by different types of bodies in different types of situa-tions are presented and discussed. It is necessary to split most geologic bodies into a series of simpler ones for which not too complicated formulas are avail-able. The gradient and differential curvature effects are calculated for each of the simple bodies and then summed to the total effect for the whole body. The calculations are considerable in number and, though more tedious than difficult, should be' entrusted to an experienced calculator. Considerable facility in qualitative interpretation can be acquired by the geophysicist from experience and from a thorough study of the types of gradient and differential curvature anomalies produced by the dif-ferent types of possible structural situations. How-ever, semi-quantitative calculations' of the probable structure bring out many relations that are not evident in a simple inspection of torsion balance results ; it throws out as impossible or improbable certain of the alternative structural possibilities that may seem equally probable under simple inspection of the results; it will determine more accurately the position of the crest of the structure; and reduce considerably the un-certainty in the interpretation and it is necessary to intelligent interpretations. The calculation of such cross-sections consists of a trial-and-error calculation of a body that will give gradient and differential curvature effects as closely as possible the same as those observed. From his knowledge of the gradient and differential curvature produced by different types of bodies, the geophysicist sketches a tentative cross-section of the structure as indicated-to him-by the observed results of the torsion balance survey, and the calculator then splits the struc-ture into blocks, and calculates the gradient and differ-ential curvature block by block. If, as rather usual, the calculated .gradient and differential curvature pro-files diverge considerably from, the respective observed ones, it is necessary to add and subtract blocks from the cross-section until a close agreement is obtained .between the calculated and observed profiles. The com-plete calculations have to be gone through for each block that is added or subtracted.

Jan 9, 1928

By Fred E. Wright

In a recent paper1 a detailed discussion is given of the possibilities of using polarized light in the examination of opaque substances. The factors underlying the problem are there treated from the viewpoint of the electromagnetic theory of light and the presentation is necessarily mathematical in form. The practical methods resulting from the discussion are, however, relatively simple and promise to be of value in the determination of certain ores and metals when studied in reflected light under the microscope. The results of the theoretical investigation referred to may be summarized by stating that in general the optical constants, such as refractive indices and absorption indices, cannot be satisfactorily ascertained on small, random, polished sections; that the use of polarized light enables the observer ordinarily to determine whether the crystal plate is iso-tropic or anisotropic, and also to ascertain the degree of anisotropism; that for this purpose methods based either on the contrast in intensity between the two reflected components of non-polarized light, or on the amount of rotation of the plane of polarization, on reflection, of vertically incident, plane-polarized light, may be employed; that methods based on the phase difference between the two reflected components are in general of little value because of the small differences in phase which ordinarily result for a relatively large change in birefringence or biabsorption. The measurement of the optical properties of transparent minerals, even in minute irregular grains, is a simple task with modern petrographic microscope methods and is accomplished by petrologists as part of their ordinary routine work. But the determination of the optical constants of opaque substances is difficult and is rarely attempted; all observations are necessarily made in reflected light and are restricted commonly to the determination of color, of hardness, of the character of crystallization, and of the behavior of the mineral or metal plate toward reagents and abrasives. With practice, the observer becomes expert in recognizing details of this kind and determines with a high degree of certainty the different

Jan 1, 1920

By Howard I. Young

WHEN so many statements are being made relative to the requirements of zinc metal, it is difficult for some of us who are acquainted with the industry to visualize how it is possible to step up production so as to supply some of the fantastic requirement figures that are published from time to time. I shall attempt to approach this subject from the standpoint of existing conditions which affect production, also keeping in mind the price ceiling under which the industry operates. Total production of primary and secondary zinc in the United States for 1941 will be about 878,000 tons, to which should be added about 36,000 tons of Mexican slab zinc available for consumption or export from the United States, giving a total available of 914,000 tons. Production of slab zinc of all grades in 1942 should be 953,000 tons. Adding the available Mexican supply should bring the total to 989,000 tons.

Jan 1, 1942

By Edgar R. Kendall

A KNOWLEDGE of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of construction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospecting for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organization there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the responsibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment. LOCATING THE SUPPLY The initial step in prospecting for mineral aggregates is the locating of suitable, adequate and economic sources of supply for the project in mind. Commercial plants in the vicinity should be investigated and a survey made of the existing structures that have been built of aggregates from these sources. If the structures are rather old and show no signs of deterioration, it is fairly good evidence that the aggregate is satisfactory. If materials of the proper quality can be obtained from commercial sources in sufficient quantity, and delivered to the job economically, it

Jan 1, 1939

By John Griffen

The modern anthracite breaker or washery uses almost exclusively a wet method of preparation, which requires, roughly, 1 gal. of water per minute per ton of production per day. The entire anthracite industry uses about 320,000 gal. per min. of water for this purpose or 800,000 tons of water per day. As this water leaves the breakers, it contains fine solids—coal, slate, pyrite, and clay—and is then called silt or slush; as slush is the term most commonly used, it will be employed throughout this paper. The solid content of the slush will be referred to as solids. In the earlier days of anthracite mining, little coal was washed, less crushing was employed, and virgin coal was mined exclusively. As a result, the slush problem was not acute because of the relatively small quantity and the coarseness of the solids. Such slush as was produced could usually be easily impounded and retained or could be discharged into streams without any appreciable pollution being apparent. The character of the fine waste from the breakers changed materially as its quantity increased until now about 40,000 tons of slush solids are produced daily. Second mining and robbing operations materially increased the quantity of fine solids delivered to the breaker in the mine car. The demand for chestnut, stove and egg sizes, to the exclusion of grate, steamboat, and lump sizes, requires finer crushing of the mine-run coal with a consequent increase of fine solids in slush. The use of rice and barley sizes removed a considerable tonnage of coarser solids from the slush but left great quantities of fine solids difficult to retain completely, and to store, and long considered of no possible fuel value. Despite the efforts of the coal operators, the slush solids have found their way into the streams causing, in some cases, serious pollution. The Water Supply Commission of Pennsylvania published, in 1916, a report on Culm in the Streams of the Anthracite Region,' from which the following is taken: About 40,000,000,000 gal. of water carrying 10,000,000 tons of fine culm are discharged into the water-courses direct, flushed into the mines, or disposed of by various means on the surface. The extent to which the very small sizes of anthracite have been deposited in the rivers draining the coal fields is made evident by the fact that over a quarter of a million tons are recovered annually from the river beds by coal-washing operations.

Jan 1, 1922

By C. Y. Cheng

THE purpose of this note is to show that the dislocation mechanism controlling the creep of Fe-4 pet Si alloy1 may equally account for the behavior of a-Fe2 over the same temperature range. A recent study of the creep behavior of a-Fe has been made by Ishida et al.2 Their results were in agreement with the mechanism of nonconservative motion of jogged screw dislocations over the entire range of temperatures investigated, from 480° to 1045°K. However, the observed creep rate was much higher than that which could be accounted for by the above model unless the authors assumed that pipe diffusion became significant below 775°K. More recently, Cheng et al.1 inves-gated the creep of Fe-4 pet Si alloy over about the same temperature range and found that the results could be correlated fairly well with a dislocation climb mechanism as represented by Eq. [l]. Proceeding as shown previously,1 if creep is controlled by a single climb mechanism, at intermediate stresses, the shear creep rate, y, can be represented by where n and K are material constants {K is independent of the temperature but dependent on the structure, that is, K decreases during the primary stage and reaches a steady-state value over the secondary stage of creep), t is the applied shear stress, G is the shear modulus, gc is the free energy of activation for creep (usually equal to that for self-diffusion, gd), and RT has the usual meaning. By solving for y, the apparent activation energy for creep, Q which can be determined experimentally, is given by where hc is the enthalpy of activation for creep which usually is also equal to that for self-diffusion, h^. By using Eq. [2], the data in Fig. 2 of Ref. 2 can be re-plotted as shown in Fig. 1. By comparing the two figures, it is seen that the slight increase in the apparent activation for creep over Region II, as noted in Fig. 2 of Ref. 2, is due to the influence of temperature on the shear modulus rather than of the stress on the

Jan 1, 1969

By W. E. Wrather

The overproduction of crude oil in 1927 has received such widespread publicity, both within and without the industry, and the several factors which have brought about this situation are so thoroughly agreed upon by everyone, that it is unlikely the writer will in this brief review be able to contribute anything new. The entire story of low prices and demoralization revolves around two flush districts, Seminole and West Texas— the actual. performance of Seminole and the potential threat of West, Texas. The sustained production of California has been a contributing factor to this situation also. It seems reasonably certain that Seminole and West Texas will together dominate the industry during 1928, with Seminole probably destined to drop into second place, as additional pipe lines are completed into West Texas to care for its rapidly expanding production. It now appears inevitable that the production of 1928 will equal or exceed that of the past year, depending solely upon the rapidity wit,h which it is possible to market West Texas crude, and the degree of restraint which operators are willing to impose upon themselves in holding proved reserves of oil underground. Adversity has cultivated the growth of a promising spirit of cooperation which has accomplished practical results both at Seminole and in West Texas. Cooperation among oil producers has long been ardently hoped for, but prior to the past year it has never been effective on an important scale. The interests both of the industry and the public at large can best be conserved by cooperation in controlling production, and the widespread acceptance of this idea has paved the way for a more rational policy in the immediate future Production BY Major Districts The domestic production of the United States during 1927 amounted to 894,43.5,000 bbl. (Bureau of Mines), an increase over 1926 of approximately 128,000,000 bbl. California succeeded in maintaining its position of the past four years at 230,000,000 hbl. In 1923 with the Los Angeles

Jan 1, 1928

By A. T. Aldred, K. M. Myles

The vapor pressure of chromium over solid V-Cr alloys has been measured by the torsion-effusion method in the temperature range 1450" to 1650°K. The chemical activities as well as the free energies, entropies, and enthalpies of formation of the alloys have hem computed from the vapor-pressure data. The activities of both chromium and vanadium exhibit fairly small negative deviations from Raoult's law over the entire composition range. The values of the excess entropies and the enthalpies of formation found at 1550°K are considered in terms of the changes in the clzaracteristic properties of vanadium and chromium that occur upon alloying. RECENT interest in the theory and properties of transition-metal alloys has shown the need for relevant thermodynamic data. The present investigation of the V-Cr system was undertaken as part of a more general study of thermodynamic properties of transition-metal alloys. The system was chosen because of the reported complete solid solubility of the components at all temperatures1 and because the difference in magnitude of the vapor pressures of vanadium and chromium allowed a simple effusion technique to be used. The torsion-effusion method was employed to minimize compositional changes in the alloys during the experiments. EXPERIMENTAL Equipment. The torsion-effusion apparatus, shown diagrammatic ally in Fig. 1, consists of a torsion system suspended inside a vertical vacuum chamber whose lower end is surrounded by a high-temperature vacuum furnace. An auxiliary optical lever and screen are used to determine the angle of rotation of the effusion cell. The torsion fiber is an annealed, high-purity, tungsten wire usually between 0.003 and 0.007 cm in diameter and about 43 cm long. The wire supports a concave mirror and a rigid tantalum connector tube. The effusion cell is fastened to the lower end of the connector tube by a dovetailed yoke and har- ness arrangement. The cells, which are 1.27 cm in diameter and 4.4 cm long, were made by electron-beam welding tantalum endcaps onto a 0.025-cm-wall tantalum tube. The two orifices, formed by drilling, have similar areas ranging from 0.011 to 0.031 sq cm. The noninductive sheath-type furnace consists of a single-phase tantalum heating element 6.35 cm in diameter, 15 cm high, and 0.013 cm thick; the element is completely surrounded by radiation shields in an evacuated chamber. The power system includes a 17-kva self-saturating saturable core reactor with an integral magnetic amplifier and a water-cooled, 15-kva, step-down power transformer with a multitap secondary. Temperatures are controlled to within ±1/2o at 1600°K by means of a unit that includes a reference voltage source, a dc electronic null detector, a current-adjusting proportional band relay, and the self - saturating reactor. At 1650°K the temperature variation within the cell, vertically and horizontally, is 3/4oK. Unwanted motions of the torsion system are damped by the movement of an aluminum vane, which is mounted on the connector tube, between the poles of an electromagnet. When not in use the magnet is withdrawn and rotated 90 deg to prevent its interaction with the rotation of the system. Measurements. The vapor pressure, p, is re-

Jan 1, 1964

Those familiar with the war in France at first hand know that in these last two years the weight of the suffering has fallen upon the families of the well-to-do classes; those who before the war lived in comparative ease and comfort, with every prospect of educating their children as their parents and grandparents had been. Thousands of the men in these families have been killed, "officiers d'élite," and the small pensions accorded the widows permit them only to house and feed their children HELÈNE JOURNÈS. and give them a common-school education. The pension for a lieutenant's widow is $245 a year; for 'a captain's, $345; for a colonel's $575; and so on. At present, it requires three francs a day to provide food for one person in cities, and conditions are not improving. The American Ouvroir Funds, 681 Fifth Ave., New York City, has tried for nearly two years to have individual Americans give individual children a "bourse," or purse, as it is called, of from $150 to $250 a year, so that they may enter such educational institutions as the Lycées, the Polytechnique, Beaux Arts, St. Cyr, etc. The war relief societies of these military schools furnish photographs and histories of children under their care and on their lists.

Jan 12, 1918

By Don L. Kendall, Martin G. Buehler

A simple physical model has been developed to fit carrier-removal data in silicon irradiated near room temperature with reactor spectrum neutrons. Commonly observed donor and acceptor defect energy levels are assumed to be introduced linearly with neutron fluence. The donor levels (in ev) are Ev + 0.16, Ev + 0.27, and Ev + 0.31 and the acceptor levels are Ec - 0.55, Ec - 0.40, and Ec - 0.1 7, where Ev and Ec are the valence and conduction band energies, respectively. The introduction rates of each level are adjusted to fit literature initial carrier-removal rate data. When normalized with respect to the Ev +0.27 level, the relative values of introduction rates are 5.3, 1.0, 3.1, 1.0, 2.0, and 20.0, respectively for the six levels indicated above. To fit p-f (hole concentration vs neutron fluence) and n-f (electron concentration us neutron fluence) data, the introduction rates are multiplied by a factor which preserves the relative values given above. This factor depends upon irradiation temperature, reactor energy spectrum, neutron fluence calibration, and oxygen content of silicon. An extensive study of the effect of neutrons on carrier-removal in silicon irradiated with reactor spectrum neutrons (E > 10 kev) has been given by Stein and Gereth1 (SG) and Curtis, Bass, and Germano' (CBG). They measured initial carrier-removal rates for both p- and n-type silicon over an impurity range typical of silicon devices. In this work, we attempt to fit a simple theory to this data to establish a usable relationship between hole and electron concentration, p and n, respectively, and neutron fluence f. The p-f and n-f relations are needed to assist in the design of neutron tolerant silicon devices and are needed to clarify presently used empirical resistivity-fluence relationships.3 Neutron damage in silicon produces a variety of defects ranging from simple point defects to defect clusters. For the purpose of this treatment, we assume that simple point defects dominate carrier-removal effects. In contrast to this view, stein4 has proposed that defect clusters are responsible for a significant portion of carrier-removal effects. In the following section, it is shown that the carrier-removal effect in n-type silicon with an electron concentration less than 1015 cm-3 can be explained adequately by assuming that the divacancy is the dominant defect and that its introduction rate is independent of the electron concentration. For electron concentrations greater than 1015 cm-= an additional acceptor defect center is needed, and for simplicity the A-center (vacancy-oxygen pair) has been chosen. Although the E-center (vacancy-phosphorus pair) can account for some of the results, the A-center was chosen because the E-center requires a more involved treatment which the presently available data do not justify. In p-type silicon three radiation-induced donor levels are assumed, namely the divacancy and two other centers of unspecified nature located at Ev + 0.16 ev and Ev to 0.31 ev. The donor divacancy at Ev + 0.27 ev is assumed to be introduced at the same rate in p-type as in n-type. However, this rate is too low to fit p-type initial carrier-removal data. The dominant centers in p-type silicon are assumed to be the Ev + 0.16 ev and Ev + 0.31 ev levels where the latter is not the divacancy. The introduction rates are chosen to fit initial carrier-removal rate data. Assuming that the introduction rates are independent of Fermi level, the ratio between them is fixed for subsequent p-f and n-f calculations. Using the same ratios, the initial carrier-removal rate data1,2 as well as p-f and n-f data1,5 can be fit provided the absolute value of the introduction rates are adjusted to account for irradiation temperature, reactor energy spectrum, neutron fluence calculation, and the oxygen content of silicon. THEORETICAL ANALYSIS This analysis is basically the same as that used by Hi116 to analyze electron damage in silicon except we express the degree to which an impurity level is ionized not in terms of the Fermi level, but in terms of carrier concentration. Landis and pearson7 have used the latter approach to analyze y-damage in silicon. Neutron-induced defects responsible for carrier-removal at room temperature are assumed to be simple point defects with no interaction between defects so that they may be represented by discrete energy levels. It is also assumed that no constituent of a defect complex is used up and defects stabilize shortly after irradiation. Defects are assumed to be introduced linearly with fluence according to the product Rtf where Rt is the defect introduction rate and f the neutron fluence. Taking into account the ionization of defects according to Fermi statistics, and considering charge neutrality where minority carriers are neglected, the n-f relation is where no is the preirradiation electron concentration. The parameter Nt is the electron concentration at which the ionized defect concentration is one-half the total defect concentration (Rtf) or where Et is the defect energy level. For silicon at 300°K, ni = 1.45 X 1010 cm-3 and Ei = Ev+ 0.542 ev which was determined using Ec — Ev = 1.11 ev and me* = 1.07 mo and mh* = 0.558m0. The spin degeneracy factor, which usually appears as a number multiplying the Nt/n term of Eq. [1], is taken as unity. In effect, this factor has been incorporated into the defect en-

Jan 1, 1970

By J. O. Edstrom, G. Bitsianes

Parabolic rate constants were determined for the formation of wiistite by the solid state reaction between magnetite and iron. The reaction was diffusion controlled and inert marker studies indicated that the mass transport through the wiistite layer was accomplished by means of iron migration. Relationships between rate constants and self-diffusivities are discussed. The transport capacity for iron through dense wustite layers was found to be sufficient to carry on reduction, even in gaseous reduction processes. REDUCTION of iron oxides has been the subject of many investigations. Most of the work, however, has been done on rather crude material and there have been difficulties in correlating the data on a quantitative basis. The reverse process of the oxidation of iron has been studied more thoroughly and usually by starting from the pure metal. As a result, the mechanisms of oxidation are now fairly well known.It has generally been found that the oxidation of metals follows the so-called parabolic 1aw;Q hat is, when the oxides are formed as dense layers, their thicknesses are proportional to the square root of the reaction time. This parabolic law follows directly from Fick's first law of diffusion The flux, J, is defined as the quantity of diffusing substance passing per unit time through unit area of a plane at right angles to the direction of diffusion. This flux is proportional to the concentration gradient of the diffusing substance, and the factor D, known as the diffusion coefficient, is introduced as the proportionality factor with dimensions of (length)'/time. If the flux is measured as the increase of thickness of the oxide layer (Ax) per unit time (t) and the assumption is made that the concentrations of the reactants at the phase boundaries of the layer are independent of time, Eq. 1 reduces to Integration of this expression yields the parabolic function ax = k . t. [31 The product of the diffusion coefficient and the concentration difference across the oxide layer is included in the constant k. When iron is exposed to a highly oxidizing atmosphere, the oxide phases are formed normally in a topochemical fashion, i.e., the interfaces between the phases maintain parallel positions to the original surface of the specimen. Above 570°C, the phases are orientated usually in the order of iron, wiistite, magnetite, and hematite, a condition in conformance with the requirements of the Fe-0 system. Below 570°C, the wiistite phase is unstable and has not been found as a normal constituent in the oxidation products of iron. There is a strong probability that continuous layers of the solid oxides are formed as the specific volumes of the phases increase in direct order from iron to hematite.' , ' Regarding mass transport through dense solid oxide layers, Wagner' has postulated that diffusion in oxides generally may be interpreted as migration processes of ions and electrons. There must be normally a concentration gradient across the growing oxide layer for diffusion to occur. This condition requires that there be deviations from the ideal stoi-chiometric composition of the oxide and accordingly deviations from the strict order of an ideal lattice. Such "lattice defects" include interstitial ions, cation and anion vacancies, quasi-free electrons, and electron holes and are decisive for all migration processes.' Cations, anions, and electrons all may have some mobility in the oxides but the movement of one of the particles generally far exceeds that of the others. Previous work', 1,2,7 has shown that during the oxidation of iron the migration through the wiistite layer, and probably also the magnetite layer, is confined to the movement of iron ions. Migration through hematite, however, has been found to take place by oxide ion movement. These behaviors are in direct agreement with the type of vacancies present in the respective oxides. Reduction of Iron Oxides The gaseous reduction of iron oxides, like the oxidation of iron, takes place in a topochemical fashion at distinct interfaces between the appearing phases."-'" Porosities might be expected in these reaction products, since their specific volumes are less than that of the starting material. Frank and van Der Merwe" have shown, however, that it is theoretically possible for nonporous layers to form if the degree of misfit in specific volume is less than about 15 pct. These aspects on porosity formation

Jan 1, 1956

By Graham Crutchfield

THE W. I. Cook pool in Shackelford County, Texas, has been the subject of a number of papers and articles. Its unique position both as to operation and development has made it an ideal location for unit repressuring. The major portion of the pool is located on the W. I. Cook ranch and most of the oil leases are owned by Roeser & Pendleton, FIG. 1.-PRODUCING SAND CONTOURS, COOK POOL, JAN. 1, 1931. Inc. and the Continental Oil Co. and operated by Roeser & Pendleton, Inc. The Humble Oil & Refining Co. and Tom James operate producing leases which have a vital bearing on the unity of the pool. Both have cooperated in the repressuring project. Practically the entire royalty is .owned by Mrs. W. I. Cook and she has given the operators her entire cooperation in all phases of unit repressuring.

Jan 1, 1931

By F. A. Forward, V. N. Mackiw

The paper relates to the laboratory and pilot plant studies that have been carried out by Sherritt Gordon Mines Ltd., Metallurgical Research Div., in developing the ammonia pressure leach process for extracting copper, nickel, cobalt, and sulphur from high grade nickel concentrate produced from Lynn Lake ores, and describes in some detail the chemistry of the process. IT is well known'.' 2 that copper, nickel, cobalt, zinc, ferrous iron, and a number of other metals combine with ammonia in aqueous solution to form complex ions of the form [Me(NH,)x]"+. The stability and solubility of these ions depend on the concentration of the metal ion in solution, on the amount of NH, present, and on the amount and type of anions present, e.g., OH-, C0;-, NO,, C1-, SO;-. If ammonia is partially or completely removed from such solutions, for example by boiling, the soluble ammines tend to decompose and the metals precipitate as basic salts. These properties of metal ammines have found practical application in the commercial recovery of copper, nickel, and cobalt from a variety of ores. In an operation formerly conducted at Kennecott"" the mill tailing containing 0.80 pct Cu as copper carbonate was leached by percolation with an ammonia-ammonium carbonate solution to dissolve the copper as the ammine. At Calumet and Hecla0-" With a mill tailing containing about 0.4 pct Cu as metallic copper, it has been found necessary to aerate the ammonia-ammonium carbonate leach solutions between stages to oxidize the solubilized copper. At Nicarol"-" where nickel and cobalt occur as oxides and silicates which are not soluble in ammonia, the ore is heated to decompose silicates and to selectively reduce the nickel and cobalt to metal, leaving the iron as Fe,O,, and is then leached with ammonia-ammonium carbonate solution accompanied by aeration to dissolve nickel and cobalt as ammines. In each of these leaching operations, the anion present is CO, and the metals can be precipitated from the leach solution as oxide (copper) or hydroxide and carbonate (nickel and cobalt) by boil- ing off NH, and C02 both of which are recycled to treat a subsequent ore charge. The products-—oxide, hydroxide, or carbonate—can be treated by conventional smelting, calcining, or electrolytic methods to convert them to refined metals. Thus the procedures mentioned utilize the properties of the ammines to extract copper, nickel, and cobalt from nonsulphide ores and separate them from the leach solutions. These processes have the advantage that they can be carried out in closed vessels at atmospheric pressure, that the leaching solutions are specific for the desired metals, that the metals can be recovered as relatively pure compounds by the boiling operation, and that the NH, and CO, can be recycled. Also, as the leach solutions after boiling and filtration are substantially free of metals, NH,, and CO,, they can be discarded, thus facilitating the control of the water balance in the leaching circuit. When, as is the case with Sherritt Gordon concentrates, sulphides are treated with ammonia solution in the presence of oxygen, the leach solution contains SO,--, and an entirely different set of conditions is encountered. The ammine sulphates (of nickel, for example) are more soluble than the carbonates and can be only partially decomposed by boiling. The SO, and NH, in the solutions can not be recovered by boiling. Thus, despite the more favorable leaching conditions resulting from high solubility of the ammine sulphates, the recovery of metals, NH,, and SO, from the solutions must be effected by other means. Sherritt Gordon Nickel Concentrate Treatment The Ni-Cu-Co flotation concentrate produced at Lynn Lake'" contains 12 to 16 pct Ni, 1 to 2 pct Cu, 0.2 to 0.5 pct Co, 33 to 40 pct Fe, 28 to 34 pct S, 8 to 20 pct insoluble, and less than 0.02 oz per ton precious metals. The nickel is present chiefly as pentlandite, the copper as chalcopyrite, and the iron as pyrrhotite and pyrite. Most of the cobalt is thought to be present in pentlandite, although it is known that a small amount occurs as Co-Ni-pyrite.

Jan 1, 1956

By Norman D. Fitz Gerald

The lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnecessary drilling.' While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a technique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer's good, while residual fuel oil is almost entirely a producer's good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

By Norman D. Fitz Gerald

The lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnecessary drilling.' While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a technique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer's good, while residual fuel oil is almost entirely a producer's good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid cobalt and a number of dilute cobalt alloys Was measured in the temperature range 1550" to 1700°C at nitrogen pressures to 1 atm. At 1600°C and 1 atm nitrogen pressure, the solubility in pure cobalt is 0.0047 wt pct [3.8 cu cm (stp) per 100 g Co]. The standard free- energy change for the solution reaction 1/2 N,(g) = gout pct in Co) is iF - 10,000 + 5.24 T cal per g atom N. The alloying elements Cv, Cu, Mo, Nb, Tu, W, and V increase the nitrogen solubility, while Al, Fe, Ni, and Si decrease the nitrogen solubility. THE solubility of nitrogen in cobalt was studied previously by Sieverts, Busch and Dodd,2 and Schenck, Frohberg, and Graf.3 Sieverts investigated the solution below the melting point of cobalt, and Busch and Dodd worked with the liquid metal; however, neither study found any solubility for nitrogen in cobalt. Schenck et al, reported a solubility of 0.005 wt pct N in cobalt at 1600°C. Seagle et al. 4 reported residual nitrogen in cobalt after electron-beam melting, although no reasons were ventured for the presence of this interstitial impurity. This investigation was undertaken to clarify these inconsistencies, and to provide additional data on atomic interactions in dilute metallic solution. EXPERIMENTAL PROCEDURE This study was well-suited to the Sieverts' method, which has not changed significantly since its introduction by Sieverts. 5 The apparatus was of the same design as that described by Humbert and Elliott, 6 with a reaction bulb similar to that reported by Weinstein and Elliott. 7 The buret was not water-jacketed, but the measured gas volumes were corrected for small changes in room temperature. The melt temperature was measured by a disappear ing-filament optical pyrometer sighted through a prism onto the melt surface. Temperature calibration was made based on a measurement of the melting point of pure cobalt taken as 1495°C. The difference between the reciprocal of the observed and the true temperatures was assumed to be a constant, neglecting the changes in emissivity with small additions of alloying elements. The total error in gas-volume measurement caused by accuracy limitations in reading the mercury level in the buret, variation in ambient temperature, and variation in melt temperature was about 0.5 cu cm. This represents approximately 10 pct of the total solubility, and is a larger relative error than in previous studies6-' because of the small nitrogen solubilities encountered in the present investigation. The source and purity of the materials used are listed in Table IA. Recrystallized alumina crucibles were used throughout the investigation. Examination of the crucibles after solidification of the melts showed no reaction or penetration. Alloying of the cobalt melt was accomplished with the dropping technique described by Humbert. 6 The investigation was started using cobalt from African Metals Corp. in shot form, but this material was not of sufficient purity and did not yield consistent solubility results. Sherritt Gordon Mines Ltd. cobalt was then used throughout the investigation. In experiments involving alloying elements which could react with oxygen dissolved in the melt, the cobalt was further refined by annealing at 1400°C in a dry-hydrogen atmosphere. This treatment, described by Woolley and Pehlke, 8 markedly reduced the oxygen content. The oxygen and nitrogen analyses of the cobalt used in this study are presented in Table IB. RESULTS Hot Volume. The hot volume was measured prior to each run and was 50 to 55 cu cm (stp) at 1600°C. It increased linearly with increasing pressure and decreasing melt temperature. Pure Cobalt. Measurements of the solubility of nitrogen in pure cobalt and the temperature coefficient of solubility are summarized in Table 11. At 1600°C and 1 atm nitrogen pressure, the solubility was found

Jan 1, 1967

By K. C. Gilbart, Edgar Stansfield

When plants decay in a peat bog the woody parts form a brown pasty mass, or peat muck, largely soluble in alkalis. This brown matter has been termed "ulmin." The same material, but commonly black in color, is found in coal, and there is evidence of the similarity between the material forming the main bulk of the coal and the bulk of the more recently decayed material in peat bogs. The more recent or low-rank coals, such as lignite, little removed from the peat stage, contain notable percentages of alkali-soluble ulmins, but the percentage decreases with increased degree of coalification and is negligible in bituminous or higher rank coals. The determination of the alkali-soluble ulmins in any coal gives, therefore, an indication of its degree of coalification or rank. Coals which contain few or no ulmins soluble in alkalis do contain ulmins which can be rendered soluble by oxidation. The higher the rank of the coal, the more difficult it is to oxidize the insoluble ulmins and make them soluble. High-rank coals can be differentiated by oxidation tests on the insoluble ulmins; but low-rank coals can be characterized by both their soluble and insoluble ulmins. This paper deals with the determination and significance of the alkali-soluble ulmins present as such in the coal. The chemical nature and composition of ulmins are not discussed. Review of Literature The history of the study of ulmin is well given by Stopes and Wheeler.' The action of potash on coal has long been known, as Braconnot in 1819 distinguished between lignites and bituminous coals by stating that the former gave colored solutions with potash. Later the intensity of color was used to give a fuller differentiation. Hoffman2 distinguished between lignites and lignitic coals by the darker color given by the

Jan 1, 1932

H. D. HIBBARD, Plainfield, N. J. (written discussion *).-While this valuable and timely paper may not go to the root of the matter, it deals with many of the elements and factors involved. It might be taken as the engineer's solution of the case, starting with the assumption that steel is steel, while the tendency for a rail to have transverse fissures may, and probably does, depend, in part at least, on conditions met before it reaches the track. Admitting with the author that "brittleness of fracture in all grades of steel is characteristic of fatigue tests" we may yet look farther back to find out, if possible, why some rails and some steels are more prone to have transverse fissures than others, for it has been found that rails from certain heats of steel developed these fissures under a service which

Jan 3, 1918