Search Documents

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By C. R. Hayward

CARLE R. HAYWARD.-I do not want it understood that I think that the conclusion that the time of tempering temperature is immaterial has been definitely proven, but since these are the first definite figures put out, I thought before continuing on more work ourselves, it would be well to present them as progress and for information. J. A. MATHEWS, Syracuse, N. Y.-I think that if Prof. Hayward would consult the paper of Profs. Barus and Strouhal,1 1885, he would find about 250 pages, mostly figures, on this subject, in which they investigated the tempering effect by electrical and magnetic methods. There are so many figures in the paper that it is very difficult reading. One point particularly brought out was that even at a low temperature, such as the boiling point of alcohol, about 60° C., there is a tempering effect, increasing up to 4 hr. One reason they obtained those results, with which the present authors are at variance, was that they started with a high-carbon steel which hardens thoroughly, whereas the steel Prof. Hayward and his collaborator used was a comparatively mild steel which does not take a great deal of hardening. About 3 years ago Mr. Stagg and I published 2 a few figures bearing on the same subject, but we used .a low-carbon alloy steel of high tempering qualities and found a great deal of improvement, particularly in ductility, by continuing the drawing up to 4 hr. We used a chrome-vanadium steel showing after heat treatment 250,000 tensile strength. On short drawing, we got almost no ductility, but by continuing to 4 hr., we raised it to 12 per cent. I believe Prof. Hayward's results are due to using comparatively mild steel, whereas Prof. Barus used drill rod and carried out a, wonderfully exhaustive

Jan 4, 1917

By M. C. Fuerstenau, J. D. Miller

The response of calcite to flotation with saturated fatty acids and alkyl sulfonates of various chain lengths is presented. The amount of collector re-quired for flotation is shown to decrease systemati-cally with increasing carbon content from 8 to 12-carbon atoms per molecule. This systematic flotation response is correlated with the solubilities of the calcium-collector salts, which were established with a nephelometer. The 14-carbon collectors deviate from this systematic behavior, and no flotation is possible with the 16-carbon homologs. As determined by infrared analysis, the mechanism of collector adsorption involves a specific chemical reaction be-tween the collector and the surface. A reaction of the form CaCO3(s)+ 2 RCOO"=*=Ca(RCOO)2(s) + C03= is suggested. The pH of the system is also shown to be a most important parameter as it controls the carbonate, calcium, and collector ion concentrations in solution and thus controls flotation response. The importance of hydrocarbon chain length of collectors was recognized early, and various studies have been made on this aspect of flotation. Wilkinson, ' for example, noted that as the chain length of alkyl xanthates is increased, the amount of collector required for flotation of sphalerite is decreased. The same effect has been shown in the flotation of galena.2 Similar results were obtained when malachite3 and calcite4 were floated with various fatty acids. DeBruyn5 has shown that a similar phenomenon occurs when quartz is floated with amines at constant pH. Recently, Fuerstenau, Healy, and Somasundaran6 correlated this phenomenon with the van der Waals cohesive free energy of association of the hydrocarbon chains. It seems unlikely, however, that chain association could be involved in the sulfide and carbonate systems with the collector additions employed, especially with the short-chain xanthates. Rather, it would seem that the decrease in collector concentration with increase in chain length noted for flotation is related to the solubility of the metal-collector salt. The purpose of this investigation is to verify this premise and also quantify this phenomenon if possible. Calcite was selected for study with both alkyl sulfonates and saturated fatty acids as collectors. EXPERIMENTAL MATERIALS AND METHODS The collectors used in this investigation ranged from 8 through 14 carbon atoms per molecule. The fatty acids had a reported purity of greater than 99%. The sodium alkyl sulfonates were provided by the Marathon Oil Cot, Littleton, Colorado, and had the

Jan 1, 1968

H. McD. Lorain says in regard to his son, Captain S. H. Lorain; "It might be of interest to you to know that, although but 23 years of age, my son is captain of Co. C 107th U. S. Engineers, Thirty-second Division. He landed in France about the middle of February, 1918, and was commissioned a captain on Sept. 5, 1918. He started for the front the latter part of June and was there continuously until the armi-stice was signed, on Nov. 11, being on the front lines in the Argonne at that time. He is, at present, in Coblenz, Germany, with the Army of Occupation. Although much of his work was clone under artillery and machine-blur fire, as well as airplane bombs and fire, he escaped without a scratch. Once, he was the only one of a group who escaped without a scratch from an exploding shell." Lieut. Bernard H. Lasky, on a post card received a short time ago, gave the following brief record of his military career. "I have been serving with the 316th Engineers in France and in Flanders and had the satisfaction of being in the last big drive in Belgium which sent the enemy beyond Avaenarde and did much to increase their gait on their way to Brussels. On Oct. 1, I received a commission as second lieutenant and was assigned to Co. C of the 316th Engineers."

Jan 3, 1919

By E. De Golyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is one of selecting test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favor- able, were usually found in anticlinal types of structure. This very understandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in parallel planes. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades, the majority of the known important oil deposits of the world have been discovered. This is but an incomplete, and the simplest, statement of the problem. Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps- anticlines, faulted structures, salt domes, etc.-but by

Jan 1, 1932

By W. M. McKewan

Magnetite pellets were reduced in flowing hydrogen at pressures up to 40 atm over a temperature range of 350° to 500°C. The rate of weight loss of oxygen per unit area of the reaction surface was found to be constant with time at each temperature and pressure. The reaction rate was found to be directly proportional to hydrogen pressure up to 1 atm and to approach a maximum rate at high pressures. The results can be explained by considering the reaction surface to be sparsely occupied by adsorbed hydrogen at low pressures and saturated at high pressures. PREVIOUS investigation1,2 have shown that the reduction of iron oxides in hydrogen is controlled at the reaction interface. Under fixed conditions of temperature, hydrogen pressure, and gas composition, the reduction rate is constant with time, per unit surface area of residual oxide, and is directly proportional to the hydrogen pressure up to one atmosphere. The reduction rate of a sphere of iron oxide can be described3 by the following equation which takes into account the changing reaction surface area: where ro and do are the initial radius and density of the sphere; t is time; R is the fractional reduction; and R, is the reduction rate constant with units mass per area per time. The quantityis actually the fractional thickness of the reduced layer in terms of fractional reduction R. It was found in a previous investigation2 of the reduction of magnetite pellets in H2-H,O-N, mixtures, that the reaction rate was directly proportional to the hydrogen partial pressure up to 1 atm at a constant ratio of water vapor to hydrogen. Water vapor poisoned the oxide surface by an oxidizing reaction and markedly slowed the reduction. The enthalpy of activation was found to be + 13,600 cal per mole. It was also found that the magnetite reduced to meta-stable wüstite before proceeding to iron metal. The following equation was derived from absolute reaction-rate theory4,8 to expfain the experimental data: where Ro is the reduction rate in mg cm-2 min-'; KO contains the conversion units; Ph2 and PH2O are the hydrogen and water vapor partial pressures in atmospheres; Ke is the equilibrium constant for the Fe,O,/FeO equilibrium; Kp is the equilibrium constant for the poisoning reaction of water vapor; L is the total number of active sites; k and h are Boltzmann's and Planck's constants; and AF is the free energy of activation. Tenenbaum zind Joseph5 studied the reduction of iron ore by hydrogen at pressures over 1 atm. They showed that increasing the hydrogen pressure materially increased the rate of reduction. This is in accordance with the work of Diepschlag,6 who found that the rate of reduction of iron ores by either carbon monoxide or hydrogen was much greater at higher pressures. He used pressures as high as 7 atm. In order to further understand the mechanism of the reduction of iron oxide by hydrogen it was decided to study the effect of increasing the hydrogen pressure on rebduction rates of magnetite pellets. EXPERIMENTAL PROCEDURE The dense magnetite pellets used in these experiments were made in the following manner. Reagent-grade ferric oxide was moistened with water and hand-rolled into spherical pellets. The pellets were heated slowly to 550°C in an atmosphere of 10 pct H2-90 pct CO, and held for 1 hr. They were then heated slowly to 1370°C in an atmosphere of 2 pct H2-98 pct CO, then cooled slowly in the same atmosphere. The sintered pellets were crystalline magnetite with an apparent density of about 4.9 gm per cm3. They were about 0.9 cm in diam. The porosity of the pellets, which was discontinuous in nature, was akrout 6 pct. The pellets were suspended from a quartz spring balance in a vertical tube furnace. The equipment is shown in Fig. 1. Essentially the furnace consists of a 12-in. OD stainless steel outer shell and a 3-in. ID inconel inner shell. The kanthal wound 22 in. long, 1 1/2, in. ID alumina reaction tube is inside the inconel inner shell. Prepurified hydrogen sweeps the reaction tube to remove the water vapor formed during the reaction. The hydrogen is static in the rest of the furnace. The sample is placed at the bottom of the furnace in a nickel wire mesh basket suspended by nickel wire from the quartz spring. The furnace is then sealed, evacuated, and refilled with argon several times to remove all traces of oxygen. It is then evacuated, filled with

Jan 1, 1962

By Theron Wasson

Michigan produced 16,637,000 bbl. in 1937. This makes it a record year in the history of Michigan's oil industry. During the year 953 wells were completed; 779 within the limits of established fields and 174 wildcats; 616 new oil wells, 68 gas wells and 269 dry holes. Table 1 has been arranged in alphabetical order of field names. Production figures for 1936 have been corrected because December figures were estimated. In this year's summary, December production is based on actual reports. The Leaton and Mt. Pleasant fields have been re-defined. Mt. Pleasant production north of the south line of Denver township, Isabella County, has been included with Leaton in accordance with usual practice in Michigan. The locations of fields discovered since the last map was published1 are shown in Fig. 1. Activity during 1937 Buckeye Field.—The Buckeye field of Gladwin County was the center of greatest activity during the year and was responsible for the increase of 4,700,000 bbl. over the state total for 1936. Buckeye produced 6,428,-000 bbl. in 1937. In this field 328 producing wells were completed during the year—over one-half the oil producers drilled in the state. Buckeye was subject to voluntary and cooperative proration from April 1 to the end of the year. Other pools of the state were not prorated. The new production at Buckeye is from porous Dundee limestone of Devonian age, similar to the older fields. Other New Fields.—The Sherman field was second in importance as a source of new production, with a total of 1,532,000 bbl. Salem township, Allegan County, on the southwest side of the Michigan Basin, was developed during the year. Production at Salem is from the Traverse limestone at a depth of 1600 ft., and 52 producing wells have been drilled in this pool. Other active pools were Clayton and Adams townships, Arenac County. The Bentley pool, discovered in October 1937 southeast of

Jan 1, 1938

By George Norman

A NUMBER of methods have been developed for the determination of the dust concentration in air, some of which have been reported as very efficient and for research may be more satisfactory than the method about to be described. In practical mine use, however, the accurate research equipment is unwieldy and requires a high degree of technical skill to manipulate it. Also, it gives less general practical information to the operator in the same length of time than the method described here. Moreover, it is doubtful whether at the present stage of affairs the results obtained from the precise methods have any more practical significance than those obtained with simpler and more portable appara-tus, which can rapidly give a sufficiently reliable indication of the rela-tive dust hazard.

Jan 1, 1937

By AIME AIME

FOR the following notes and pictures we are indebted to Sumner S. Smith of Oakland, California: Gold was discovered on Squaw Creek in the fall of 1927 by an Indian named "Paddy Duncan," and most of the stream was staked by natives. This stream is about 12 miles in length and flows into the east fork of the Alsek River, 10 to 15 miles below the old Dalton Post in British Columbia, near the international bound-

Jan 1, 1929

By Michael E. Zellars

The environment for deposition of marine phosphorite is controlled by the relationship of prevailing climatic, oceanographic, structural, and sedimentary conditions. The set, or sets, of conditions that has evoked the accumulation of economic concentrations of phosphorite has been the subject of a number of previous works. Phosphorite presently considered ore is generally in excess of 10% P205 with an extractable phosphate product in excess of 30% P2O5. The concentration of the product in the ore, its amenability to state-of-the-art extraction, and thickness of the overburden are major controlling factors in determining its mineability. A recent survey of phosphorite deposits in the south-eastern United States included a review of the depositional and structural setting for the major areas of occurrence. The application of previous work regarding phosphorogenesis has led to the establishment of a general depositional model for most mid-Miocene primary phosphorites, and, is also possibly applicable to the Bone Valley (Pliocene-Miocene) district of central Florida.

Jan 12, 1978

By C. T. Liu, J. Gurland

The deformation behavior in tension of spheroidized carbon steels was studied at room temperature as a function of carbon content, 0.065 to 1.46 wt Pct, and carbide particle size, 0.88 to 2.77 p. It was found that the Hall-Petch strength-grain size relation is directly applicable to the yield and flow stresses of the two lower-carbon steels , 0.065 and 0.30 pct C. The strength data for the medium- and high-carbon steels, 0.55 to 1.46 pct C, also satisfied the Hall-Petch relation, provided that these data are based upon the particle spacing. Beyond 4 pct strain, the flow stress data of all the steels studied could be represented by the same Hall-Petch relation with dinerent spacings for grain boundary and particle strengthening. The behavior of the higher-carbon steels was consistent with the postulated formation of a dislocation cell network during processing and initial deformation (up to 4 pct strain). The cell size was assumed to be equal to the planar particle spacing. The true stress at the ultimate tensile strength was also found to be a function of the particle spacing. At a given temperature and strain rate, the yield and flow stresses of carbon steels depend on the type and dimensions of the microstructure. Starting with the work of Gensamer et al. in 1942,' experimental studies on pearlitic and spheroidized carbon steels revealed that the strength of steels is a function of two main parameters: the ferrite grain size2'3 and the carbide particle spacing;1'4'5 on this basis, two different strengthening mechanisms have been developed to apply to steels of low and high carbon contents, respectively. In polycrystalline iron and mild steels the grain boundaries are regarded as the major structural barriers to slip. The relation between strength and grain size is generally represented by the Hall-Petch equation which is based on a linear proportionality between strength and the inverse square root of the average grain size.2'3y677 However, Gensamer et al.' and Roberts et related the yield strength of medium -and high-carbon steels to the carbide particle spacing alone, and they found a linear relation between the logarithm of the mean free path in the ferrite and the yield strength in both spheroidized and pearlitic steels. By means of the electron microscope, Turkalo and LOW' extended the study to finer structures; they concluded that the logarithmic relation is not valid for the entire range of microstructures unless grain boundaries are also included in the measurement of the mean free path. For the specific case of spheroidized steels, Ansell and aenel' found that the yield strength data,4'5 when plotted as a function of mean free path, fit the Hall-Petch equation; however, T'ysong found that the same data fit the 0rowanl0 relation if a planar inter-particle spacing is used. Recently Kossowsky and ~rown" studied the strength of prestrained spheroidized steels, 0.48 and 0.95 pct C, and concluded that the strength due to the carbide dispersions varies linearly with the reciprocal of the square root of the mean free path between carbide particles and dislocation networks. Such networks were first observed by Turkalo." The conclusion common to all these studies is that the available slip distance in the ferrite is the most important variable in determining strendh. Previous work on carbon steels is restricted to limited composition and strain ranges. The mechanism which governs the flow properties is not clearly understood, and, in particular, little is known about the composition dependence of the transition between grain boundary strengthening and particle hardening. The purpose of the present work is to investigate the strengthening mechanism in spheroidized steels over a wide range of carbon content, 0.065 to 1.46 wt pct, and plastic strain, yielding to necking. The spheroidized structure was chosen because of its relative simplicity and the relative ease of control and measurement of the structural parameters. The experimental work is limited to tensile testing at room temperature at constant extension rate. The effects of the carbide particles on the fracture behavior of spheroidized steels are discussed elsewhere.13 EXPERIMENTAL PROCEDURE Eight different grades of vacuum-cast carbon steels were supplied in the form of forged and rolled plate by the Applied Research Laboratory of the U.S. Steel Corp. The compositions furnished with these steels are given in Table I; the carbon content ranges from 0.065 to 1.46 wt pct, or from 1.0 to 22.3 vol pct of carbide. The steel plates were cut transversely into rods a little larger than the test specimens, 1 in. gage length, i in. diam. The rods were austenitized in air (enriched with CO by a consumable carbon-rich muffle) at 50° C above theA, orA., temperature for 2 hr and then quenched in oil with vigorous stirring. The as-quenched rods were tempered in two stages in order to obtain the desired distributions and sizes of carbide particles. The rods were first tempered at 460° C for 10 hr and then at 700" C for periods ranging from 4 hr to 3 days, in vacuum. After final machining, all specimens were vacuum-annealed again at 650°C for 1 hr in order to relieve residual stresses. The tension tests were carried out in two steps. The initial part of the load-strain curve, up to about 2 pct strain, was determined on a Riehle testing machine with an extensometer of small strain range, 4 pct strain, in order to obtain the yield and initial flow piopertiesi As soon as the first part of the test was finished, the specimen was placed in an Instron testing machine equipped with a strain gage extensometer with a maximum strain range of 50 pct. The load-strain curve to fracture was

Jan 1, 1969

By H. A. Wilmeth

IN 1955, before planning an accelerated stripping program, Chino Mines Div. began an engineering study to improve data for estimating truck haulage costs for any future haulage layout. The study aimed to develop: 1) significant unit costs, 2) a method of estimating travel time from which truck needs and future stripping rate could be determined, and 3) yardsticks of performance to measure haulage efficiencies. It was suggested that to provide significant unit costs, expense accounts should offer management two types of cost control information-unit cost yardsticks with which monthly unit costs could be compared and unit costs for estimating future expenses for any haulage layout.

Jan 5, 1958

By Carl Swartz

ALTHOUGH a number of articles appeared during the war advocating the use of cadmium in lead-tin solders, very little information of value can be found in the literature regarding the properties of solders containing cadmium. In most of the published articles the cadmium seems to have been considered merely as a partial substitute for tin in a tin-lead alloy rather than as an essential constituent of a ternary alloy. The primary object of the substitution of cadmium for tin was to lessen the amount of tin required, at a time when the latter was scarce and high-priced, and thus to produce a cheaper solder. While this object was accomplished, the new properties resulting from a change from a binary lead-tin alloy to a ternary lead-tin-cadmium alloy were not given proper consideration in many cases. For the past few years, the American Smelting & Refining Co. has been marketing a very considerable amount of cadmium in the form of lead-tin-cadmium alloys for use as solders for certain special purposes, and the successful use of these solders suggested that if more extensive knowledge were available concerning the properties of lead-tin-cadmium alloys of various compositions their field of usefulness might be materially extended. The investigation described in the present paper was undertaken to obtain this information and, by means of tests under conditions approaching those of practical use, to determine the suitability of cadmium solders for various purposes.

Jan 1, 1928

By H. J. McQueen, G. C. Kuczynski

ThE useful properties of k6-Alfenol and the thermenol alloys (summarized by J. E. Nachman and W. J. Buehler') have encouraged research into those alloys which, having compositions near 25 at. pct Al, 75 at. pct Fe, undergo an ordering transformation between 500° and 550°C. The equilibrium diagram of the iron-rich iron-aluminum alloys was first determined by Bradley and Jay.2,3 They distinguished three structures: the disordered, which is bcc; FeAl, which is simple cubic with one Fe atom and one Al atom per lattice site; and Fe3Al, which is fcc with three Fe atoms and one Al atom per lattice site. This last structure may be conceived as eight body-centered cubes with Al atoms at the centers of alternate ones, so that Al atoms have only Fe as first and second nearest neighbors. Later, Osawa and Murata4 determined the boundaries of the different superlattice regions in the iron-rich Fe-Al solid solution by dilatometric and X-ray methods. Two of the six phases, which they found between 0 and 50 at. pct Al, were never identified by other workers. A. Taylor and R. M. ones,' concurrently with and independently of this research, redetermined this diagram by measuring lattice parameters at temperature. Further reference will be made to their results. EQUILIBRIUM DIAGRAM A) Experimental Procedure—The alloys were prepared from NRC gas-free iron (99.9 pct Fe) and 99.99 pct Al. They were melted in alumina' crucubles under vacuum in an induction furnace. If the ingots were unsound or showed more than a 3 pct weight loss, they were rejected. The ingots were homogenized at 1100°C for 24 hr before hot-rolling at 700" to 900°C from 1 in. to 0.25 in. thick. It is interesting to note that alloys containing more than 28 at. pct Al were able to take an 80 pct reduction of area in the ordered FeAl region. The dilatometer specimens and specimens for chemical analysis were cut from these plates. A Leitz dilatometer was used to measure the coefficient of linear expansion as a function of temperature. The specimens were slowly cooled from 900" to 300°C where they were annealed for 10 hr before slowly cooling to room temperature. The expansion was recorded photographically as the alloys were heated and cooled at 1.5oC per min between 100" and 1000°C. The magnetic measurements determining the Curie points were performed on the dilatometer specimens in the dilatometer, by using direct current in the furnace windings both to heat the specimen at 1.5°C per min and to serve as the primary coil. The regular specimen holder was replaced by a thin alundum tube on which was wound, as a secondary, a closely spaced coil of fine copper wire. A reversal of current in the furnace windings produced, in the secondary, an emf which was proportional to the induction in the specimen, and which could be detected on a galvanometer. In this way, it was possible to determine the Curie points of alloys to within * 5°C. B) Results and Discussion—The coefficients of linear expansion, as obtained from the dilatometer curves, are plotted as a function of temperature and composition in Fig. 1. Since in many cases the heating and cooling curves were superimposed, it was decided to measure slopes of heating curves only. Definite high peaks, due to the transformations, were observed on each curve between 400" and 520°C, and, for alloys containing more than 23 at. pct Al, a second set of smaller peaks at temperatures above 660°C. The sharpness of the peaks indicates that ordering to Fe3Al is a first-order reaction. The compositions and the temperatures of these peaks are listed in Table I. When these temperatures are plotted as a function of the composition, the result is the constitution diagram presented in

Jan 1, 1960

By C. E. Birchenall, R. H. Condit, M. J. Brabers

In the oxidation of pure iron above 700°C the overall rate is determined mainly by the rapid growth of wiistite, through which iron ions can diffuse rapidly.' Nickel added to the iron progressively decreases the stable range of composition of wustite.' When enough nickel is added to eliminate wiistite as a stable phase, the spinel is the fast growing phase. This investigation was undertaken to test the hypothesis that nickel substituting for iron in magnetite might decrease the rate of spinel growth by reducing the iron mobility. Nickel ferrite boules grown by the flame fusion process were purchased from the Linde Co. Chemical analysis gave an atomic ratio of iron to nickel of 2.88 and showed no other cations. They were cut into discs and ground to give flat, parallel faces. The experimental procedure employed was like that of Eisen and Birchenall in which the distribution of radioactivity diffused in from a vapor deposited surface layer was determined by counting the residual activity through a series of ground faces. The diffusivities were calculated in a manner consistent with the requirements discussed by Condit and BirchenallP The details will be given in connection with a more extensive spinel diffusion study now in progress. The results of the measurements are shown in the figure in comparison with earlier data on magnetite1 and zinc ferrite. The uncertainties arising from scatter in the activity vs distance relationship and uncertainties in the temperatures are shown by flags. Despite the scatter it is clear that substitution of a considerable part of the iron in magnetite by nickel, in this case about one third decreases the iron mobility substantially. sachs' determination of the distribution of iron and nickel in scales on iron-nickel alloys appears to show that nickel is less mobile than iron in the spinel layer. It is evident, therefore, that nickel plays several roles in reducing the oxidation rate of iron-nickel alloys. 1) It reduces progressively the stability range of wiistite. ' 2) It reduces progressively the stability range of the iron-nickel spinel phase in terms of the variation in cation to anion ratio.' 3) As shown in this investigation, it reduces the cation mobility in the spinel phase which is the faster growing phase in the absence of wiistite. The fe was obtained from the Oak Ridge National Laboratory. The research was supported by the Air Force Office of Scientific Research (ARDC) under contract number AF 18(600)-967.

Jan 1, 1961

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By Francis H. Crockard

DURING the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of stream-lined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements.

Jan 1, 1935

By D. J. Carney, E. C. Rudolphy

Large macroscopic nonmetallic inclusions were related to altered fireclay refractories by chemical and microscopic means. Pouring refractories are discussed as a source of these large inclusions. Nozzles and wells are major contributors. Use of alkali and titania contents as tracers is described. Recommendations are offered to minimize the sources of inclusions from pouring refractories. IN any attempt to improve the cleanliness of plain carbon and alloy steels, consideration must be given not only to the proper deoxidation practice to minimize inclusions, but also to sources of inclusions from pouring refractories. In some cases, the inclusions resulting from deoxidation may be minor in amount, yet a relatively dirty steel may be produced as a result of improper care in the pouring practices for the steel. The number of studies of inclusions resulting from pouring refractories has increased recently and some excellent reports on this subject have already been published.'4 Some of these reports were reviewed briefly in a companion paper by M. P. Fedock.5 Mr. Fedock's contribution is a fine addition to the studies necessary to improve steel cleanliness for the ultimate benefit of all steel producers and consumers. In the interest of constantly improving cleanliness, the authors have been actively engaged for the past two years in experimentation to determine more closely the sources of inclusions in steel. One phase of this work was associated with efforts to define more closely the sources of macroscopic inclusions which have been experienced on occasional heats. The term "macroscopic inclusions" is defined in general as those inclusions which are visible to the naked eye or at low magnifications of the order of less than X25. These inclusions sometimes can be seen in the macro-etch tests of billets and slabs. This report summarizes a few of the field experiments and laboratory studies conducted at the South Works of the United States Steel Corp., which were made regarding nozzles, wells, and ingot scums, as well as inclusions occurring in steel products. The data in the present study, together with the data of Mr. Fedock concerning ladle erosion, should be of value in regard to future studies of inclusions arising from pouring refractories. The knowledge gained as a result of data collected thus far at South Works has been helpful in improving the cleanliness of the products and in pointing the way toward further improvements. Similarity of Large Inclusions to Refractories and Altered Refractories In the routine inspection of billet etch tests, occasional inclusions visible to the naked eye have been observed. These large inclusions most frequently occur near the top of the ingot and near the billet surface. When such material was encountered, careful examinations were made in an attempt to determine the origin of these inclusions. In a relatively few cases, examination revealed that the material was unaltered fireclay refractory of a type similar to that used for hot-top material, with only the surface of the inclusions having an altered appearance under the microscope. However, the great majority of these inclusions were completely altered-refractory material. The term "altered refractory" is defined

Jan 1, 1955

By Y. Nakada, U. F. Kocks, B. Chalmers

The stress-strain behavior of the gold single crystals in easy glide was found to be affected by the specimen dimension which is parallel to the projection of the Burgers vector of the primary-slip system. The larger this dimension is, the larger is the slope of easy glide. Previously severa1 investigators attributed the size effects to either the existence of surface films or the grip constraints. However, in this experiment both of these possible causes were not present. It is proposed that the length of slip path (defined as the crystal dimension parallel to the Burgers vector of the primary system) is the controlling factor in the size effect observed in gold. THERE are many possible effects of the specimen dimension on the work-hardening behavior of single crystals: grip effects which prevent end regions of the crystal from deformation or rotation; effects of a surface film, for example a coherent oxide; effects of a subsurface layer of accidental or intentional

Jan 1, 1964