Search Documents

By N. Arbiter, J. Steininger, C. C. Harris

Power consumption and operating variables in air-liquid systems for a wide range of operating conditions in the turbulent region have been correlated by two dimensionless groups involving the power ratio and the flow number. The form of the correlation was developed by considering flow balances related to the air-liquid composite density in the impeller zone. Data for two phase air-liquid systems, both from literature and from the present investigation, has been correlated with high statistical significance. Two phase solid-liquid and three phase gas-liquid-solid systems have also been correlated. The quantification of power requirements in the agitation of liquids is well established.1 Rushton, Costich and Everett have shown that, for mixers operating in the fully turbulent region with no vortex, the power number

Jan 1, 1964

By R. W. Fountain, W. D. Forgeng

A new constitutional diagram is presented for the cobalt-rich end of the cobalt-titaniurn system. The modifications result from the presence of a new, intermediate, fcc phase, ?, the existence and homogeneity limits of which were established by metallo-graphic and X-ray studies of alloys containing from about 3 to 30 pct Ti. The precipitation of the ? phase from supersaturated solid solution was studied by hardness and electrical resistivity measzsrements, and two distinct stages in the process were observed. COBALT forms the base for a number of precipitation -hardenable alloy systems which may be divided into two distinct categories of practical interest, a) those hardened by intermetallic compounds and b) those hardened by carbide formation. The precipitation of intermetallic compounds from solid solution in cobalt-rich alloys has, however, received very little attention. Although the phase diagrams for some binary systems capable of precipitation have been determined,' there is an almost complete lack of data on the property changes associated with the precipitation, and even less information on the kinetics of the reactions or morphology of the products. More information is available on the precipitation of carbides because of the practical significance in superalloys. A survey of cobalt binary phase diagrams suggested that the cobalt-titanium alloys might provide interesting and useful precipitation-hardenable alloys. The equilibrium diagram as proposed by Wallbaum2 is shown in Fig. 1. Köster and wagner3 have indicated that the maximum solubility of titanium in cobalt is about 10 pct at the eutectic temperature (1135oC), and this decreases to about 7.2 pct at room temperature. The temperature of the allotropic transformation in cobalt is lowered by the addition of titanium, about 5 pct being sufficient to retain the high-temperature fcc modification to room temperature. Wallbaum and Witte 4,5 have indicated that the precipitating phase in alloys containing up to about 29 pct Ti is Co2Ti, a hexagonal Laves phase of the MgNi, type. With slightly higher titanium contents, they also report a cubic modification of Co2Ti of the MgCu2-type Laves phase. Duwez and Taylor6 confirmed the existence of the hexagonal (MgNi2) modification but not the cubic (MgCuz) modification of Co2Ti and suggested that existence of the cubic form may have resulted from impurities in Wallbaum's alloys. In their work on Laves-type phases, Elliott and Rostoker 7 reported the cubic modification of Co,Ti, but did not confirm the existence of the hexagonal modification. However, Dwight8 in a discussion of the work of Eliott and Rostoker again showed the existence of both modifications of Co2Ti, a result which was confirmed at that time by Elliott and Rostoker. As a result of a study on the iron-cobalt-titanium system, Köster and Gellers suggested the existence of a Co3Ti phase isomorphous with Fe3Ti. Witte and Wallbaum,' however, established the fact that no compound, Fe3Ti, exists in the iron-titanium system, and in a later publication, wallbaum2 stated that Kitster and Geller's reasoning was not valid, and no compound, Co3Ti, exists. This conclusion was later acknowledged by Köster.10 Preliminary experiments by the present authors to determine the precipitation-hardening characteristics of the cobalt-rich, cobalt-titanium alloys re-

Jan 1, 1960

By R. Priestner, R. F. Krause

Solid, cylindrical crystals of a iron have been fractured at 10°K by the simultaneous application of tension and torsion stresses. Thus, a complex distribution of normal (sN) and shear (ss) stresses existed in a cleavage plane at fracture. In every crystal the clearage-plane normal was inclined to the specimen axis, so that a unique point, M*, in the operative cleavage plane was defined where the quantities sn and s2 N + s2 S) were maximized. It is shown that the maxirrzum resolved normal stress on the cleavage plane at fracture decreased as the resolved shear stress in the cleavage plane at M* increased. Thus, a normal stress la?*! for fracture was not satisfied. A fracture law which takes shear stress into account. and which predicts that (s2 N +s2S) should be constant, is to be preferred. However, the data is best represented by a linear dependence of sN on sS, sS which 110 physical significance can be attached. It is suggested that the fracture-nucleating -mechanism is a short-range one. A critical stress law has not yet been unequivocally established for the propagation of cracks in metals. Measurements of the tensile fracture stresses of variously oriented zinc single crystals1 failed to establish the normal stress law expressed by In Eq. [1], sN is the fracture stress, P, resolved normal to the fracture plane, and 0 is the angle between the fracture -plane normal and the stress axis. Similarly, a comprehensive investigation failed to verify the normal stress law for the tensile fracture of a-iron single crystals.' However, a subsequent investigation,3 using iron from the same ingot, presented fracture data which obeyed the normal stress law. It has been shown previously4,5 that the Griffith criterion for fracture6 does not predict such a normal stress law. This result is of particular significance in considering the fracture of metals, such as zinc and iron, which may fail by cleavage. In these metals fracture propagates in a well-defined "cleavage" plane, whether or not an applied stress is normal to it. When the cleavage-plane normal deviates from the direction of application of a uniaxial stress, for example, the crack propagates under the combined action of normal (sN) and shear (ss) stresses. When the presence of a resolved shear stress in the crack plane is taken into account, the Griffith criterion is expressed by4

Jan 1, 1967

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the -pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint .of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth .history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By C. A. Bruch, J. F. Duffey

On the basis of metallographic and cooling-rate studies of 15 U-Zr alloys, a new version of the 6 phase region of the U-Zr phase diagram is proposed. IN several published diagrams of U-Zr alloy system:' there is good agreement that at elevated temperatures complete solid solubility exists between y uranium and ß zirconium. Similarly, there is reasonably good agreement concerning the uranium-rich and zirconium-rich ends of the diagram. However, there is no agreement concerning the nature of the diagram at intermediate compositions and at temperatures below about 650°C. The early work of Saller et al.8 hows an intermediate phase, 6. In a later diagram by Saller and Rough' shown in Fig. 1, the d phase field is drawn with dotted lines, indicating doubt that this phase exists. The diagram of Summers-Smith2 does not show the d phase. More recently Holden and Seymour' have shown that in the composition range 40 to 60 wt pet Zr, the high-temperature ? phase, which is body-cen-tered-cubic, transforms to an ordered structure, 8. They found that the order-disorder transformation occurs between 595° and 610°C, and presented a diagram based on the study of four different alloy compositions. Most recently Saller et a1.5 presented a new diagram which differs with respect to the composition limits of the 8 field from the others proposed by these authors. The purpose of the present investigation was to determine the boundaries of the d phase field. Experimental Procedures and Results Alloys—Buttons, weighing 80 g of 15 different alloy compositions were prepared by arc melting Mal-linckrodt uranium and iodide-process zirconium in a water-cooled crucible. A controlled atmosphere of argon and helium was maintained in the furnace. Prior to making each button, a sacrificial button of zirconium was melted to increase the purity of the furnace atmosphere. Each alloy was then melted six times to improve its homogeneity. Subsequently the alloy buttons were jacketed in copper and hot rolled to slabs at 775°C. From these slabs, specimens were machined for chemical, thermal, and metallographic analyses, Table I gives both the estimated chemical composition of the alloys, and the values which were obtained by analysis. The oxygen contents varied from 0.013 to 0.032 pet, nitrogen from 0.0014 to 0.014 pet, and carbon from 0.0013 to 0.011 pet. The purity of the alloys ranged from 99.947 to 99.975 pet. Thermal Analysis—The specimens for thermal analysis were blocks 11/4 x 1/4 x % in. The bead of a calibrated thermocouple was placed between two of these blocks and molybdenum wire was wrapped around the assembly. Each assembly was sealed in a quartz capsule having an argon atmosphere. The capsule was placed inside a refractory crucible which was heated in a furnace. Using a method described by Smith,' the emf of a differential thermocouple, with junctions inside and outside of the refractory crucible, was used to activate the

Jan 1, 1959

By Theron Wasson

During 1936 the state of Michigan produced 11,868,573 bbl. This is approximately 4,000,000 bbl. less than produced in 1935. The principle reason for the decrease in production over the previous year was the rapid decline of the Crystal field, which reached its peak in October 1935. The old producing area—Mt. Pleasant, Porter, Yost-Clark— accounted for over 7,000,000 bbl. during 1936. Crystal produced a total of 2,400,000. Outstanding among the old fields were Vernon and

Jan 1, 1937

By B. M. Larsen, T. E. Brower

INTRODUCTION AND SUMMARY BY "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath, To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over 1 million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct, The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 lb oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 lb oxygen replacing 145 lb ore per ton of steel) decreased the

Jan 1, 1948

By J. M. Flaitz, A. S. Parks

OF the various methods of sampling gas-condensate wells, a method that secures a continuous representative sample of the well stream is desirable. Such a method, consisting of a sampling tube introduced into the well tubing, has proved satisfactory. The method is sufficiently accurate for operating and engineering problems. A portable testing apparatus can be used with the sampling tube to obtain data useful in studying the economic and technical aspects of the development and operation of gas-condensate properties. INTRODUCTION The recent discovery and development of gas reserves that contain hydrocarbons that condense with reduction of temperature or pressure, or both, to form a product known as condensate, has brought many new problems to the oil and gas industries. With further discovery of deep, high-pressure fields it is presumable that many more gas fields of this type will be added to the steadily increasing number. Such gas reserves are found either associated with oil as a gas cap or in separate formations. There seems to be no positive correlation between the physical or geological nature of the reservoir, and the chemical composition or phase characteristics of its contents. Knowledge of the chemical make-up and phase behavior of gas-condensate reserves are needed to cope with many problems. A knowledge of the chemical composition and phase characteristics of the reservoir material is necessary to properly design a gasoline or recycling plant, to estimate natural gas and condensate reserves, to enable the operator to study the economic and technical aspects of various methods of operation and development, and to carry out the plan of operating subsurface and surface lease equipment. This information is often useful in questions of mineral ownership, proration, legal position, and taxation. It is the purpose of this paper to discuss methods used by the writers to determine the chemical composition and phase characteristics of the fluids produced from a condensate well. The scope of the paper includes a discussion and description of the method of sampling, the results of tests on the accuracy of the sampling method, a description of a portable testing apparatus used to examine the phase characteristics, typical results of tests on wells from several condensate fields, and some of the applications of these data to production problems. References to previous work on this subject are cited at the end of the paper. THE PROBLEM At reservoir conditions of temperature and pressure, the fluids produced from a condensate well exist in a homogeneous vaporous condition. The consequent reduction of temperature and pressure that occurs as this gas enters and flows up the well tube results in condensation of some of the hydrocarbon material to form a liquid. The relative amount of liquid condensed at any point in the flowing system

Jan 1, 1941

By Byron W. Cheever

While engaged in experimenting with the usual methods for estimating phosphorus in iron and steel, it occurred to me that potassium chlorate might be used to oxidize the carbon, and thus avoid the tedious and vexatious evaporations necessary for successfully carrying out the usual methods. After many trials, the following plan was adopted : Take, for analysis, of Bessemer or other low-carbon steels, from 3 to 5 grammes; of crucible steel, 10 grammes; of pig-iron, 1 to 5 grammes, according to the percentage of phosphorus supposed to be present. Of iron, high in phosphorus (1 per cent.), take 1 gramme. Place in a No. 4 evaporating dish the amount of iron or steel decided upon, cover with a funnel which will just fit inside the dish, and then add gradually HNO3, (1.20 specific gravity), using 12 C.C. of acid for each gramme of steel or iron taken. (A larger quantity of acid will be required for small samples.) When the full amount of acid has been added, and the violent action has ceased, place the evaporating dish on a sand-bath, add 10 C.C. HNO3, (1.40 specific gravity), and boil till the bulk of the solution is reduced about onehalf. Then add 10 C.C. HNO3, (1.40 specific gravity), continue the boiling, and add from time to time, during the next 15 minutes, small portions of pulverized KCIO3, till about 2 grammes have been added. (If the solution shows signs of going dry, more strong acid must be added.) This will precipitate the manganese, with some iron. Sometimes it happens that the manganese does not come down readily, and more KCIO3, or further concentration, or both, will be required. The process is not complete till the manganese is precipitated, which may be known by the appearance of a dark, mirror-like deposit on the dish, at the edge of the solution. Boil the solution 5 minutes after the last addition of KCIO3, and then add cautiously (to prevent sudden explosions) 5 C.C. strong HCl. This will dissolve the precipitated manganese and iron. Continue the boiling till the chlorine is all expelled, adding from

Jan 1, 1885

By D. H. Turner, F. A. Crossley

The titanium-rich corner of the system Ti-Al-Si has been studied to determine the phase relationships in the temperature interval 600° to 1200°C. Metallographic examination of long time isothermally annealed specimens was the means of investigation. PART of a program on phase relations and transformation processes of titanium alloy systems included the study of the titanium-rich corner of the Ti-Al-Si system. The investigation covered ternary compositions in the range 2 to 8 pet A1 and 0.1 to 2 pet Si and binary compositions in the range 0.2 to 2 pet Si. Temperatures were in the range of 600" to 1200°C. Alloys containing 6 pet A1-0.1 to 0.5 pet Si were investigated down to 400°C. Partial vertical sections are presented for 2, 4, 6, and 8 pet Al. The Ti-Si system has been reported by Hansen et al.' It is characterized by a eutectoid decomposition, ß = ± a + Ti3Si3, at 860°C. The maximum solubility of silicon in a is reported to be about 0.5 pet at the eutectoid temperature. The solubility of silicon in 0 increases from 0.9 pet at the eutectoid temperature to approximately 3 pet at the eutectic temperature, 1330°C. Several investigations in the composition range of interest have been reported for the Ti-A1 system."' These investigations are in agreement on the phase fields, but differ to small extents on boundary positions. However, very recent, and as yet unpublished, findings" " indicate that there are perhaps two phases which occur at lower aluminum contents than the ? (TiA1) phase, and that the solubility of aluminum in a titanium is less than 6 pet. In the present investigation phase relations found are in agreement with the published literature exemplified by the work of Bumps et al.3 Therefore, it is probable that the partial system reported herein is metastable and does not represent true equilibrium. Experimental Procedure High purity Bureau of Mines titanium sponge of 103 Bhn hardness, granulated aluminum shot of 99.7 pet purity, and silicon powder of 99.8 pet purity were used in making the alloys. For the work in the range from 600" to 1200°C, 100 g ingots were prepared by arc melting. Melting losses were negligible and spot checks by chemical analysis showed good agreement between nominal and analyzed results. Nominal compositions are used throughout this paper. Ingots were forged to 3/8 in. rounds and cut into specimens for heat treatment. Isothermal anneals in the range from 600" to 900°C were preceded by solution treatment at 1000°C for 1 hr, followed by furnace cooling to the annealing temperature. Samples were sealed in evacuated Vycor bulbs for heat treatments up to 1000°C. Higher temperature anneals were done with the samples sealed in quartz bulbs under a partial pressure of argon.

Jan 1, 1959

By Enrique Touceda

As IN the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time. A few years ago, about the only test made to ascertain the physical properties of the product, t except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in, castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 2, 1920

By R. J. Borg, C. E. Birchenall

The self-diffusion coefficients for a iron have been deternzined between 980° and 1167° K using Fe55 as the tracer. With decreasing temperature the diffusivity was found to decrease more rapidly than predicted by the Arrhenius equation in the region of the Curie temperature. The diffusion coefficients obtained well above the temperature of the magnetic transformation are more precise ard differ substantially from all the previously reported values. In the temperature region beginning at least 50" above T,, the diffusion coefficient is given by D = 118 (±2) exp 1 HE self-diffusion coefficients for a iron have been reported previously as the result of four independent investigations The general lack of agreement and the poor precision of most of the previous work prompted the redetermination by the present authors. The possible effect of the onset of ferromagnetism upon the diffusivity5 provided an additional impetus for this investigation. The earlier measurements of Birchenall and Mehl1 gave low values for the diffusion coefficient at temperatures below the Curie temperature, Tc. However, the precision of these measurements is not sufficient to establish an indisputable correlation between the low values and the magnetic transformation. The results of this investigation along with all the previous ones are shown in Fig. 1. EXPERIMENTAL Small rectangular samples, approximately 1 by 0.5 by 0.3 cm, of high-purity iron (Vacuum Metals Corp., "Ferrovac") are first heated in hydrogen at 900°C for24hr in order to remove possible trace amounts of dissolved carbon and oxygen. The small

Jan 1, 1961

By J. J. Pelley

NOT being a scientist, an engineer or a metallurgist, I consider it a very great honor indeed to be asked to address the American Institute of Mining and Metallurgical Engineers. Your program indicates that any lack of intricate and technical knowledge on my part in the field of metals will be well taken care of by others. Therefore, I believe any remarks that I have to make might well be devoted to the practical side of metals in railroad service and to the general railroad situation as I view it today. The experiments now being conducted on the railroads with so-called streamlined, light-weight trains and cars would not have been possible had it not been for scientific and engineering research in the past that made these lighter weight metals available. The railroads now have approximately forty units of these new trains in operation. Experi-ence with them will no doubt be a guidepost for future construction in that direction. While the best known experiments are in the passenger service, they are being extended into the freight service. Within the past three years there was constructed for the Association of American Railroads a new standard box car of ordinary carbon steel, in which, by reason of superior design, weight was reduced by 3500 to 4500 lb. under that of existing cars of like capacity. The Association is now testing a box car that weighs approximately six or seven tons less than practically all of the box cars of like capacity in service today. If these tests are successful a very large field for the use of lighter weight metals will immediately be opened, provided the costs of such metals are not too high. The fact that various experiments are being carried on with other classes of equipment constructed with so-called light-weight and non-corrosive metals no doubt will have a considerable effect upon the rebuild-ing of old equipment. The question then will be: How much can we afford to spend on the rebuilding of an old car weighing six to seven tons more than a new car constructed with the latest available materials?

Jan 1, 1936

By John Blatchford, H. O. Hofman

The leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which, according to Pélabon,' is 550°C., according to Wagemann2 540°C., and according to Borgstroma 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343", if 0.1 to 0.2 mm.; and 430" if 0.2 mm. 3. The fusibility of a mixture of Sb2S33 and Sb203 which in the form of kermesite (Sb2S3)z.Sbz03 melts at 517°C.6 4. The volatility of Sb2Ss and SbzOs, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures. As regards the oxidation of metallic antimony, we have the experimental evidence of C. F. Plattner6 that when fused and brought to a red heat, it burns with a bluish-white flame to Sb2Oa which passes off as a

Jan 1, 1916

By C. L. T. Edwards

IN the preparation of this paper, the author has drawn upon experience with the operation of a blast furnace on 100 per cent scrap burden, which he believes was the first operation of its kind in the country. It is the writer's further belief that much of the controversy attending discussions of this subject may be obviated by the presentation of a group of facts that should be known by blast-furnace men and open-hearth men alike. The following question has been raised: "Is iron made with scrap in the blast-furnace charge as good iron as that made without scrap-made with straight ore?" This question may be answered in part by the fact that the open-hearth men of the Bethlehem Steel Co. who used pig iron from a blast furnace that operated on 100 per cent steel scrap found no difficulty in the processing of such iron other than that to be expected from the known analysis. OPERATION WITH 100 PER CENT STEEL SCRAP During World War I, there was accumulated at the Bethlehem plant of the Bethlehem Steel Co. some 22,000 tons of alloy-steel turnings and borings. This scrap material was highly corroded and, like alloy-steel turnings of that period, were as a drug on the market. There was also a small tonnage of scale, rich in valuable metal. If this scrap could be worked up into pig iron, it would become readily available for use in the open hearth. In order that the pig iron should contain the maximum percentage of nickel, permission was obtained from the Management to try a 100 per cent scrap operation. Accordingly, a blast furnace was swung over on July 25, 1919; the percentage of steel scrap increased more or less irregularly until July 29, when l00 per cent steel turnings were charged. Except for occasional charges of nickel scale as an "extra," the operation continued uninterruptedly until Aug. 27, when the furnace was swung back to the regular ore-ore and scrap-operation. During this period, the furnace production ranged from a low of 568.60 tons to a maximum of 766.07 tons. At the swing-over from i00 per cent scrap to the regular burden, the charge hung up rather severely. While the latter condition has nothing to do with the object of the paper, a brief discussion of the experience will appear later because of the interest it may have for blast-furnace operators. In Table I, results of the first and last days of the ore charge are shown, July 25 and July 29. The last column shows a summary for the period of maximum scrap charge. The furnace employed had a hearth 16 ft. 0 in., bosh 22 ft. 0 in., stock line 15 ft. 6 in., bell 11 ft. 6 in., batter ¾ in., bosh angle 73° 27' and a Baker-Neuman top, with gas-engine blowers. Analyses Range of Material Charged Gravel: Si02, 64.40 to .7o.54 per cent; A1203,3-52 to 4.58; CaO, 7.27 to 9.49; M90, 5.09 to 6.14; FeO, 1.67 to 3.34, ignition loss, 9.50 to 13.83.

Jan 1, 1941

By J. C. Mertz, C. H. Mathewson

Accurate knowledge of the solid solubilities of the elements that dissolve in the important base metals is needed for guidance in the preparation and heat-treatment of the alloys derived from these components. While there is still difference of opinion concerning the merits of the X-ray and microscopic methods of determining such solubilities, it is certainly true that the recent extensive use of X-ray diffraction to review the existing constitutional data has revealed many glaring inaccuracies and has brought about a much improved knowledge of phase-boundary locations, which will inevitably come to include all of the important alloy systems. When the work is done with all necessary precautions it appears that in the majority of cases where the solubilities extend beyond a few tenths of a per cent the X-ray back-reflection technique is capable of furnishing the best of information in this field. For the most prolonged and thorough studies it is obviously advisable to combine the results of several methods, in particular, to obtain an agreement between X-ray and microscopic data. This paper reviews the work previously done on the solubilities of phosphorus, arsenic, antimony and bismuth in copper and, in consideration of the uncertainties thus made apparent, presents new X-ray data obtained with the first three members of this group. Copper-phosphorus System Heyn and Baurl found that in slowly cooled alloys phosphorus forms a solid solution with copper up to about 0.175 per cent. Huntington

Jan 1, 1937

By R. S. Bradley, B. K. Miller

The principal producing areas of fire clay in Missouri are: (I) the east central district, which includes Audrain, Callaway, Montgomery, Warren, and Boone Counties (Fig. I); (2) the St. Louis district, which includes St. Louis and St. Louis County; (3) the north central Ozark district, which includes Franklin, Gasconade, Osage, Maries, Phelps, and Crawford Counties. Most of the semiplastic‡ fire clay is found in Audrain, Callaway, Montgomery and St. Louis Counties, and in St. Louis. Flint fire clay is found in Callaway, Audrain, and Montgomery Counties and in most of the north centra! Ozark district. High-alumina diaspore clay is found only in the north central Ozark district, except a few deposits found in Montgomery County. This paper is concerned with the semi-plastic fire clay that occurs in the east central Missouri district near Mexico, Audrain County, Missouri, which is mined by the open-pit method as practiced by the A. P. Green Fire Brick Co. About one-fourth of the semiplastic fire clay in that district is mined in shaft mines, and three-fourths in open pits.

Jan 1, 1942

By B. K. Miller, R. S. Bradley

The principal producing areas of fire clay in Missouri are: (I) the east central district, which includes Audrain, Callaway, Montgomery, Warren, and Boone Counties (Fig. I); (2) the St. Louis district, which includes St. Louis and St. Louis County; (3) the north central Ozark district, which includes Franklin, Gasconade, Osage, Maries, Phelps, and Crawford Counties. Most of the semiplastic‡ fire clay is found in Audrain, Callaway, Montgomery and St. Louis Counties, and in St. Louis. Flint fire clay is found in Callaway, Audrain, and Montgomery Counties and in most of the north centra! Ozark district. High-alumina diaspore clay is found only in the north central Ozark district, except a few deposits found in Montgomery County. This paper is concerned with the semi-plastic fire clay that occurs in the east central Missouri district near Mexico, Audrain County, Missouri, which is mined by the open-pit method as practiced by the A. P. Green Fire Brick Co. About one-fourth of the semiplastic fire clay in that district is mined in shaft mines, and three-fourths in open pits.

Jan 1, 1942

By N. C. J. Ros

The paper deals with pressure gradients occurring in flowing and gas-lift wells, a knowledge of which can be applied to the determination of optimum flow-string dimensions and to the design of gas-lift installations. The study is based on a pressure-balance equation for the pressure gradient. It appears that a pressure-gradient correlation of general validity must essentially consist of two parts-—one part being a correlation for liquid hold-up and the other part being one for wall friction. Dimensional analysis indicates that both liquid hold-up and wall friction are related to nine dimensionless groups. It is shown that in the field of interest only four groups are really important. On the basis of these four groups a restricted experimental program could be selected that nevertheless covered practically all conditions encountered in oil wells. This experimental program has been carried out in a laboratory installation. Three essentially different flow regimes were found. The pressure gradients in these regious are presented in the form of a set of correlations. Comparison of these correlations with a few available oilfield data showed excellent agreement. INTRODUCTION Prediction of the pressure drop in the flow string of a well is a widely known problem in oilfield practice. Accurate data on the pressure gradient of a simultaneous flow of gas and liquid in a vertical pipe are especially useful for the determination of optimum flow-string dimensions. It is well known that with moderate gas and liquid flows such a vertical string acts as a "negative restriction". The pressure drop decreases (1) when the throughput through a given pipe increases, and (2) when at a given throughput the cross-sectional area is decreased. The reason is that, with increasing velocities, the flow becomes more agitated so that the gas slips relatively more slowly through the liquid. With the resulting increase in gas content in the string, the static head decreases. When the area becomes very small, however, the high velocities entail great wall friction, which causes an increase in pressure drop. For a given flow, therefore, minimal pressure drop is obtained by using a certain cross section. This means that, in principle, each well can be provided with an optimum flow string for minimum pressure drop and, hence, maximum possible production rate. The procedure for the selection of the optimum string has been discussed by Gilbert.' A necessary tool in the procedure, however, is accurate knowledge of the pressure gradient to be expected for various values of the governing variables. Another application of pressure-gradient data lies in the field of gas-lift practice: they provide a means of determining the optimum gas-injection rate, optimum injection pressure and optimum injection depth. Much work has already been done in the study of the pressure gradient of vertical gas-liquid flow. Poett-mann and Carpenter2 presented a pressure-gradient correlation based on measurements in wells. This correlation has been found to provide accurate predictions in high-pressure wells and in high-production wells for flow through both tubing and annuli.2-5 However, when their method is checked on low pressure-low production wells or on wells with viscous crudes, serious discrepancies are found. As we shall see in the next section, this is due to the fact that their correlation factor, representing all irreversible energy losses, is given as a function of only one correlation group. Some important variables, such as gas-liquid ratio and liquid viscosity, are not incorporated in this group so that their specific effects are not accounted for. To study also the mechanism of vertical gas-liquid flow outside the ranges covered by the Poettmann-Carpenter publication and extensions, a laboratory investigation has been carried out. This study is founded on a pressure-gradient equation that is based on a pressure balance. To reduce the number of test runs required, a dimensional analysis has been carried out, followed by a selection of relevant dimensionless groups. These groups guided a subsequent experimental study, and with their aid the experimental program could be minimized while still covering the majority of the situations encountered in oilfield practice. In this paper the choice of a formula for the pressure gradient is discussed first. This is followed by a brief description of the experimental setup. Subsequently, the dimensional analysis is discussed and the relevant dimensionless groups are selected, resulting in the experimental program required. The general relationships of pressure gradient and liquid hold-up are then described; various flow patterns and a certain flow instability (so-called "heading") are discussed and a set of correlations is presented which shows a good agreement with the measurements and a few available field

By George F. Sowers

THE geophysical methods of exploration employed so extensively in mining and petroleum investigations are now being used in civil engineering. Requirements differ from those of mineral ex- ploration and therefore modified techniques have been developed. The civil engineer is primarily interested in the uppermost soil and rock strata. In highway engineering the materials affecting design and construction may be found within 15 or 20 ft of ground surface, and data on soils and rocks is seldom needed for more than a depth of 100 ft even for the heaviest structures.

Jan 1, 1954