Search Documents

By E. A. Ernst, N. F. Carpenter

The benefits derived from an acidizing treatment are a function of the penetration achieved by the acid before complete spending. Additional penetration may be achieved by (1) controlling acid leak-08 into formation pores in the channel faces, and (2) retarding the reaction rate of the acid. A recently developed chemical additive consists of a synthetic polymeric material which absorbs hydrochloric-acid solutions, when suspended therein, swelling up to 40 times its original volume. These swollen particles have the ability to deform and seal-08 formation pores, providing fluid-loss control. In addition, they provide a diffusion barrier between the fracture face and the acid solution, prolonging the spending time of the acid. Field applications of this new technique have shown promising results. A method of conducting acid fluid-loss tests, using carbonate cores, is believed to provide fluid-loss data that are more representative of formation conditions than the conventional filter-paper determinations. INTRODUCTION The concept of oilwell acidizing has changed since its first commercial application, 30 years ago. Originally, it was visualized that the acid penetrated thousands of tiny pores and flow channels in the matrix rock, enlarging them by dissolving the carbonate walls. The resultant permeability increase was assumed to be the responsible factor in increasing production from the well. Recent laboratory studies,' however, have shown that this does not provide the complete picture. Although this type of individual pore penetration by the acid does take place during acid "soaks", designed to overcome "skin effect" due to mud invasion in the immediate vicinity of the wellbore, many years of experience have shown that considerable pressure is required to attain any appreciable injection rate into the fine capillary pores of the rock. During most acidizing treatments, the bottom-hole pressure build-up due to the restriction of flow into the formation exceeds the "breakdown" pressure of the rock so that a fracture is induced. In most cases, such fractures open up along natural, incipient fissures and zones of weakness in the rock and, therefore, tend to follow the natural stress pattern of the rock—whether it be horizontal, vertical or inclined. Because of the comparatively greater permeability of the channel in relation to that of the matrix, the bulk of the acid volume is diverted into the newly opened fracture. Here it quickly penetrates the formation, opening and ex- tending the fracture in much the same manner as a conventional fracturing fluid. Unlike the fracturing fluid, however, most acidizing solutions contain no propping agent; thus, the open fracture will again close when the injection pressure is relieved. Laboratory studies2 have shown that in many cases the etching of the fracture faces, resulting from the reaction between the acidizing solution and the carbonate rock, is nonuniform due to the heterogeneity of the rock structure. As a result, the two fracture faces no longer match when pressure is released, and support pillars and intermediate voids remain, forming a high-conductivity channel for well fluids. Unfortunately, this is not true over the entire area of the fracture, but only over that portion of the fracture where the rock has been partially dissolved by the acid. The acid solution spends as its travels away from the wellbore; once it has completely spent, even though it may provide additional mechanical fracture extension, no additional benefit due to etching of fracture faces can be expected. Studies of acid reaction rates under formation conditions,3 observing the effect of different variables upon spending time, have shown that the reaction was often so rapid that very little penetration of the formation occurred before the acid was spent. Study was undertaken to devise methods of increasing the penetration of the acid before spending, so as to provide greater benefit from the acidizing treatment by etching a greater portion of the fracture faces. Several techniques were devised to accomplish this purpose. First, chemical additives were developed which were designed to retard the reaction rate of the acid, causing it to penetrate a greater distance from the wellbore before finally becoming spent. Another method was to increase the injection rate of the acid. However, it was found that the resultant increased shear tended to accelerate the reaction rate of the acid, partially offsetting the benefits of the higher injection rate insofar as achieving increased penetration before spending was concerned.' Another approach to the problem of achieving increased penetration was the development of fluid-loss additives for acid solutions, which would minimize the volume of acid lost into formation pores in the fracture faces and provide maximum fracture extension for the volume of acid injected during the treatment. The use of fluid-loss additives is now considered the most effective method of providing maximum fracturing-fluid efficiency.~ Unfortunately, this latter technique does not solve the problem of rapid reaction rate, with consequent limitation of the fracture area benefited by reaction with unspent acid. A newly developed acid additive overcomes many of these limitations by providing the dual benefits of fluid-loss control and mechanical retardation of acid reaction

By N. N. Breyer

A specially built "hard" tensile machine with characteristics permitting the precise detertnination of the drop of the load at the yield point has been used to study the magnitude of the yield-point phenotnenon in prestrained martensitic 4340 steel. A new phenonzenon, the appearance of a secondary yield point, has been observed by holding the specimen at constant strain in the plastic region. Furthermore, it has been found that a series of yield-point drops could be introduced by successive constant strain holds in the plastic region. The isothermal kinetics of the development of the secondary yielding point lave been studied at four temperatures: 24° 0° -18°, and -79°C. From the results of the kinetic investigation, equations for the In a previous investigation1 it was shown that, contrary to generally held opinion, steels of medium carbon content, such as 4340, 4140, and 86B30, in the as-quenched martensitic condition, can be cold-drawn through a die with reductions in area of up to 10 pct without cracking. Tensile specimens of 4340 machined from bars quenched and prestrained in this manner exhibited tensile strengths of about 400,000 psi coupled with 30 pct reductions in area. In addition, it was found that each sample of such steels exhibited a yield point in the quenched, cold-drawn condition. Since these studies were conducted on a commercial hydraulic testing machine of a type which is not well-suited to detailed study of yield-point behavior, it was decided to study this phenomenon more thoroughly on a rigid straining machine. In this new investigation, use of such a "hard" machine not only allowed study of the magnitude of the yield-point drop but also revealed a new phenomenon—secondary yielding of the martensite introduced by stopping crosshead motion after plastic deformation of the sample had begun. The present paper is a report of these findings. MATERIALS AND PROCESSING The material used was a commercial 4340 steel of the composition shown below: 0.41 0.80 0.013 0.019 0.31 0.85 1.76 0.28 1 0.42 0.77 0.015 0.024 0.30 0.84 1.69 0.28 0.08 2 1 = Ladle analysis. 2 = Laboratory analysis. Bars of this steel were processed in the following way: 1) machined to predetermined diameters; 2) austenitized at 870°C for 1 1/2 hr; 3) oil-quenched; 4) cooled to -115°C for 1/2 hr; onset and increase in magnitude of the secondary yielding in this temperature region have been found to fit the relationship ?Ys = Atn where ?Ys is the magnitude of the secondary yield Point in psi, t is the time in seconds, and A and n are parameter characteris-tics of the material. Although the occurrence of the primary and secondary yield points could be rationalized qualitatively on the basis of stress-induced ordering of carbon atoms in the stress fields of dislocations, as postulated in an earlier paper, the kinetics of the secondary-yield-point development were interpreted to indicate that the ordering involves more than just single jumps of carbon atoms from high-energy to neighboring low-energy sites. 5) pickled and lime-coated; 6) drawn through a carbide die. The predetermined diameters were chosen so that drawing through the same die gave the various reductions desired. Tensile specimens of 0.252 in. diam with a 1 1/4 in. gage length were then prepared from the drawn bars and tested. In order to study the stress-strain behavior at the yield point in detail, a rigid tensile machine with a high spring constant was constructed. Columns of large cross section (relative to the specimen cross section) constituted the machine frame. A dc motor was used to drive a screw via a gear reducing train and a "crane" thrust bearing. In this relatively simple device small deformations could be observed un-blurred by the slow response and lower spring constant inherent in hydraulic machines.' A strain-gage dynamometer permitted load changes as small as 8 lb to be read. RESULTS Tensile test samples machined from bars in the as-quenched condition with no subsequent drawing and samples from bars with 3.8 pct reduction after quenching gave stress-strain curves typified by those shown in Figs. I and 2. The time lapse between predrawing and tensile testing varied but usually ranged between 3 to 6 days at room temperature. The strain rate during testing was 0.003 in. per in. per min. The as-quenched curve is seen to have a broad serrated maximum whereas the stress on the specimen prestrained 3.8 pct rose linearly to point A, Fig. 2, fell abruptly to B, and then gradually to C. The abrupt drop to B was accompanied by evidence of incipient necking. The drop of the stress at the yield point in the prestrained samples (A to B in Fig. 2) changed with the percent prestrain, as illustrated on Fig. 3. Although the tensile strength increased continuously with the amount of previous cold drawing, the magnitude of the yield point drop first increased—up to about 6 pct prior reduction—and then decreased. Specimens from bars predrawn more than 8 pct broke in a brittle fashion in the elastic portion of the stress-strain curve.

Jan 1, 1967

By R. J. Bethancourt, D. M. Collingwood

The use: of a pilot waterflood is very desirable where all of the pertinent data necessary to initiate a full scale waterflood are not. available. This paper attempts to take a specific case and .show the step by step process of starting with a pilot waterflood and progressing to a full wale flood as results are obtained. INTRODUCTION Many of the older fields of Soutlwest Texas are approaching depletion by primary produrtion methods. As primary protlllc:inp operations on individual properties approach their economic limit. conflicting considerations face management: cm the one hand. plugging and abandonment of wells for equipment salvage; on the other hand, further investment in secondary recovery installtions, equilent, and well workovers in the interests of conservation anal additional oil reserves. In main instances, where primary production by pressure depletion and gas solution drive has been comparatively good, there still exists the possibility of an economic secondary recovery by waterflood. This is not necessarily true to the same degrre of all such fields. nor all portions of large fields. To properly evaluate the economics of a prospective water-11ot1cI requires a considerable amount of precise geological. statitical. and physical data Such information on the older field.; is often very limited. and in the case of the property discussed in this paper was considered inadequate to justify investment in an overall waterflood. Primary production was estimated at :39 per cent of the original oil in place, yet sand conditions of permeability and homogeneity, and position in the field appeared to be favorable for a limited margin of profit from a carefully controlled waterflood. Thus a pilot waterflood, with its minimum initial financial risk, followed by extension as favorable results were obtained, seemed to be the answer for the Sun Oil Co L. Wiederkehr lease in the Nortl Government Wells Field, Duval County. Texas DESCRIPTION OF RESERVOIR Approxinately 8,200 wells have been drilled in Duval County. As of March 1, 1952, there were 3,350 producing oil wells in 92 different fields, with very few flowing wells (Fig. 1.) Sun Oil Co. operates the I.. Wiederkehr lease located in the North Government Wells Field in Duval Countv. 85 mile. west of Corpus Chriti and 100 miles south of San Antonio. The lease has been subjected in part to a controlled five spot waterflood. The North Government Wells Field is roughly 7 miles long and 3 miles wide, with numerous overlapping producing zones. The L. Wiederkehr lease of 3.085 acres. Has seven producing zones from 700 to 7.500 ft. The lease is in the northern section of the field where it is widest, and has 710 acres productive from the North Government Wells .and. (Fig. 2.) The North Government Wells sand, Jackson group. Eocene age, at an average depth of 2.250 ft (minus 1.750 subsea). has a thickness range of 25 ft on the east side of the L. Wiederkehr lease to 4 ft on the west side. It has a slight overall dip to the North and East of some 33 ft to the mile.

Jan 1, 1953

By R. M. Brick

AN increased demand for information in regard to the effect of gaseous elements in steel has accompanied the recognition of the importance of grain size. Attempts to correlate grain-size characteristics with gas con-tent, particularly oxygen in solution or in the form of included metallic oxides, have not been universally successful. Certain definite effects of dissolved gases are recognized; specifically, the role of hydrogen in causing internal cracks or "flakes" and that of nitrogen in preventing excessive grain growth of ferritic chromium steels. When irregular behavior or properties are found in a well-known steel and no definite cause for the abnormality may be assigned on the basis of chemical and metallographic tests, dissolved gases are frequently blamed as the culprits. The solubilities of hydrogen1 and nitrogen2 in pure liquid iron are known but of the ternary systems, iron-alloying element-gas, only the Fe-Si-N3 and Fe-Cr-N systems have received attention and here the study was confined to liquid alloys. Krivobok4 published a curve show-ing the solubility of nitrogen in liquid Fe-Cr alloys but gave no informa-tion on the experimental procedure employed. The considerable experimental work reported on the Cr-N binary alloys has been reviewed by Hansen.5 It is generally agreed that the nitride CrN is a stable phase although the existence of nitrides within limited temperature ranges of stability, viz., Cr3N2 and Cr2N, has been disputed, Adcock6 and others7 have reported a eutectic between Cr and CrN at 1580°C., although the supporting evidence is not complete.

Jan 1, 1940

By K. Tangri, M. Chaturvedi

On water-quenching from within the (a + ß) phase region Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys can undergo w transfirmation. This transformation has been attributed to the enrichment of ß Zr phase, at the solution-treatment temperature, by the solute atoms. The ß—w transformation is accompanied by a hardening 01 the alloys and in the optimum condition w-bearing specimens of the ternary alloy are about 14 pct harder than those bearing only a' phase. On aging crl reverls thermally to more stable phases, which results in a considerable softening of the specirnens, as follows: w quenched -waged + ß Zr (enriched) waged - a + ß Nb The high-temperature bcc ß Zr in certain zirconium alloys can transform to a metastable w phase which has a primitive hexagonal structure. In the Zr-Nb alloy system w phase has been observed in the composition range of 7 to 15 wt pct Nb by a number of investigators.'-' In this composition range w can form by water-quenching ß Zr or by aging. known as athermal and thermal w, respectively. Hatt and Roberts' have found that thermal w has a constant c/a ratio of 0.622 +0.002 regardless of the composition and tha: the lattice parameters are of the order of a = 5.02A and c = 3.0 ?. The actual lattice parameters depend upon composition and the temperature of aging. The lattice constants of athermal w. however, depend upon alloy composition.3 The presence of w phase in zirconium alloys can cause substantial strengthening which has been attributed as probably due to the coherency between w and parent ß Zr phase. Robinson et al.' found that the presence of w can raise the strength of Zr-5.0 Nb-2.0 Sn and Zr-5.0 Mo-2.0 Sn alloys to about 170.000 psi: however. the ductility is considerably reduced. With the growing use of Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys in the nuclear reactors, and the significant effect of w transformation on the mechanical properties of zirconium alloys studies were undertaken to study the w transformation in Zr-2.5 Nb and Zr-2.5 Nb-0.5 Cu alloys. This paper is concerned with the formation and reversion of w phase in these alloys. 1) MATERIALS AND EXPERIMENTAL TECHNIQUES The following two alloys were studied: 1) Zr-2.5 Nb-0.5 Cu (referred to as the ternary alloy): 2) Zr-2.5 Nb (referred to as the binary alloy). The chemical analysis of the alloys is given in Table I. The alloys, in the form of 3/8-in.-diam rods and 1/8-in.-thick sheets, were supplied by the Chalk River Nuclear Laboratories of the A.E.C.L. Initial fabrication for preparation of various specimens was carried out by cold rolling and swaging with intermediate anneals at 1000°C. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-% m of Hg. For optical metallography and hardness measurements disc specimens + in. diam by + in. thick were used. After the required heat treatments the specimens were mechanically and then chemically polished in a 45 pct HNO3, 45 pct H20. and 10 pct HF solution. The hardness measurements on the chemically polished specimens were carried out on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative hardness value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using copper K-a radiations in 114.6-mm-diam camera. Thin films for transmission electron microscopy were prepared by electropolishing heat-treated a by 7 by 0.005-in.-thick strips using a modified Bollmann-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol electropolishing bath was kepl at -5OCC and polishing was done at 5 to 10 v. The thinned specimens were washed in ethyl alcohol at -30" to -40°C and dried between filter papers. The thin films

Jan 1, 1970

By J. M. Markowitz

The movement of hydrogen in two-phase Zircaloy-2 under the influence of a thermal gradient was studied in specimens of cylindrical geometry. A gross displacement of hydrogen toward the cooler regions of the specimen was observed with consequent copious precipitation of 6-ztrconium (ZrH) there. The kinetics of the diffusion are analyzed and discussed. X HE temperature-gradient redistribution of hydrogen in a-Zircaloy-2 has been treated both theoretically and experimentally Hydrogen moves toward the cold side of the temperature gradient until a steady state has been established; tendency for further hydrogen movement because of temperature differences is nullified by the tendency to move in the reverse direction because of the concentration gradient. The steady state condition is described by the equation in which iV is the concentration of hydrogen at a point in the specimen corresponding to absolute temperature T, R is the gas constant,k is a constant of integration, and Q is a parameter called the heat of transport, characteristic Of the particular system. The value of Q has been determined for hydrogen in Zircaloy-2 by several investigators, using Eq. [11. There is considerable variation in the results, the cause of which has not been resolved; reported values lie in the range 3 to 6 kcal per mole. The physical situation for two-phase thermal migration is much more complex. The -phase boundary for the solubility of hydrogen in Zircaloy-2 ranges from a concentration of 25 ppm at 200°C to a maximum of about 600 ppm at 550°C.4a Thus, if the concentration of hydrogen in Zircaloy-2 is sufficiently great (>600 ppm), the specimen will be entirely two-phase, consisting of a matrix of a-Zircaloy-2 surrounding particles of zirconium hydride. At time zero, with a temperature gradient imposed, the relative amounts of hydride and a-phase in each infinite-simally thin isothermal section of the specimen can be determined from the phase diagram by the lever rule. Moreover, the concentration of hydrogen in the matrix phase varies from point to point, following the a solubility line. Over most of this temperature range (<450°C) 6 phase, Fig. 3, has a constant concentration.5 The diffusion rate toward the cold side should be governed by 1) the slope of the a solubility line and 2) the temperature gradient, The extra complication of two-phase thermal diffusion lies in the fact that migration of hydrogen would leave the a-phase concentration gradient unaffected, since it is fixed at any temperature only by the solubility; gross concentration changes would reflect only the relative amounts of matrix and hydride, which could vary continuously at every point. Migration of hydrogen out of a region would lead to dissolution of hydride, and

Jan 1, 1962

By John M. Cummings, Warren. Harry V.

THE Geology Department of the University of British Columbia has undertaken the task of examining the ores from as many as possible of the gold mines of British Columbia. The object of this work is two- fold. First, it is known that detailed mineralographic studies are useful in attacking ore-dressing problems, and these studies are intended to be helpful to mill operators. Second, it is hoped that mineralogical and mineralographical studies will prove useful adjuncts to those of lithology and structure in throwing more light on problems related to the origin of the deposits. The paper shows that gold, for all practical purposes, is not present in an ore mineral in solid solution nor as a eutectic with any mineral; if the latter were true the gold particles would be distributed equally throughout that mineral. The gold occurs either as native gold or as a gold-silver telluride and is not distributed regularly through any mineral or minerals. The relationship between the gold or gold-bearing telluride and the associated minerals affords a means of classification that is not only simple but also appears to be directly related to the geological nature of the deposit, which may be summarized as follows: 1. Disseminated Gold Type.-Precious minerals in extremely small grains, which are distributed without regard to grain size, fractures or grain boundaries: (1) Hedley variety-gold in native form; (2) Surf Point variety-gold predominantly as telluride. 2. Veining Gold Type.-Precious minerals in grains of various sizes, which occur mainly along fractures and grain boundaries: (1) Cariboo gold quartz-goldin native form. (2) Waneta variety-gold as telluride. Application Te Ore Dressing These mineralographic studies have proved to be of value to mill operators, and future studies of a similar nature should prove increasingly useful because every year provides a further opportunity to correlate

Jan 1, 1937

By H. B. Bailey

SiNcE the gypsum deposits of Nova Scotia have been operated on a large-tonnage basis, it has become increasingly necessary that more study be given to the geological relation of gypsum to anhydrite. It was while attempting to work out some definite system of quarry operation for several operators that the factors relating to hydration as given in this paper became apparent. For convenience the words "the formation" are used to mean anhydrite and gypsum taken together as one bed geologically and forming a distinct unit from the rocks below or above. Also, the word "block" is used geologically to define a portion of the formation that is cut apart and separated by erosion from other portions. The formation is part of the Lower Carboniferous, the remainder of which is made up of red shales and shaly sandstones, coarse red conglomerates and limestones. Overlying the Lower Carboniferous are the even-bedded gray sandstones of the coal measures. To a large extent these sandstones have been eroded from above the formation and the usual cover is clay and unconsolidated sediments. The position of the limestone member which immediately underlies the formation usually furnishes the key to the general structure. Being harder, and subject to less erosion, it has a wider spread than the&apos;formation, and measures for dip read on it have a value which can not be applied to dips taken on gypsum or anhydrite. This limestone usually is not more than 25 ft. deep, but it has a remarkable tenacity—one would almost say elasticity—under strain of earth movements. In many cases it stands as a barrier to the erosion which otherwise would have destroyed completely the remaining block of the formation. No bedded limestone is found within the formation except in narrow seams close to the bottom and in short irregular masses in highly disturbed strata where it has been caught up by fault action. This paper is not concerned with the general theories of original deposition and no opinion is expressed as to whether gypsum or anhydrite was first deposited from evaporating sea water. For purposes of study, and as an observed fact, except in the few cases where there has been extreme disturbance, a block of the formation is regarded as a block of anhydrite which has become partly hydrated into gypsum. 177

Jan 1, 1931

By A. J. Miller, G. R. Brophy

THE Grossmann principle1 for the calculation of hardenability of steel from composition is attractive because of its simplicity. It postulates that the hardenability of a steel for any particular grain size may be expressed in terms of an ideal critical diameter, which is the product of an ideal critical diameter for a "pure" iron-carbon base multiplied by a succession of factors for each element of composition contained, including the incidentals. It infers that the multiplying factor for a given quantity of an element is constant for all combinations of composition. Grossmann has stated that in the great majority of cases the experimental values of hardenability are found to be well within 10 per cent of the calculated values. The validity of the scheme has been confirmed in principle by Crafts and Lamont2,3 and by Kramer et al .4 Their results differ from the original in the magnitude of the effect of some elements but, since they accepted the product concept and followed its direction, it is to be expected that similar results would be obtained. Crafts and Lamont, in their second paper, recognized that the factor relations for manganese and nickel were not continuously linear, but beyond certain critical amounts increase sharply. Austin, Van Note and Prater5 demonstrated nonlinear relations between hardenability and alloy contents. Their curves for chromium, silicon, manganese and nickel were all convex upward to show decreasing incremental effects. They concluded that Grossmann&apos;s factors underevaluate the hardening effect of low percentage additions of these elements, and overevaluate the larger additions. [ ] More recently W. Steven6 has found that the factor method fails when applied to complex steels containing two or three principal alloying elements other than carbon. Multiplying factors derived from his results bear a complex relation to composition and are not constant for a given amount of an element as the base composition varies. C. A. Liedholm7 found that, using either the Grossmann or the Crafts-Lamont multiplying factor values, not only were

Jan 1, 1945

By H. C. Gatos, A. D. Kurtz

WITH the growing interest in the mechanism of self-diffusion of metals, the study of accurate and convenient methods for determining self-diffu-sion coefficients appears highly desirable. It was with this objective in mind that the present investigation was undertaken. Gatos and Azzam1 employed an autoradiographic technique for measuring self-diffusion coefficients of gold. This method involved sectioning of the specimen through the diffusion zone and recording the radioactivity directly on a photographic film. Because of the very short range of the emitted ß rays in gold, the activity recorded on the film was essentially the true surface activity. With proper choice of the sectioning angle, sufficient resolution could be obtained and the entire concentration-distance curve recorded in one measurement. For the boundary conditions of the experiment, where an infinitesimally thin layer of radioactive material diffuses in positive and negative directions into the end faces of a rod of infinite length, the solution of the diffusion equation is C/Cn = 1/v4pDt exp (-x2/4Dt) where C is the concentration of diffusing element (photographic density in this case), C,, is the constant (depending upon amount of radioactive material), x is the diffusion distance, D is the diffusion coefficient, and t is the time. Thus, by plotting the logarithm of the concentration vs the square of the diffusion distance, a straight line results and the slope contains the diffusion coefficient. In this manner, the self-diffusion coefficient of gold can be obtained as a function of temperature. In the present investigation the results reported by Gatos and Azzam1 have been verified, and the autoradiographic technique has been further developed and applied for the determination of the self-diffusion coefficient of gold at a number of temperatures. Furthermore, the energy of activation for the self-diffusion of gold has been conveniently determined. . Experimental Techniques Preparation of Specimens: The inert gold of high purity was received in the form of a rod from which cylinders were cut and machined to a diameter of 0.500 in. The specimens were annealed to a suitably large grain size and the faces were surface ground prior to the deposition of the radioactive layer. The radioactive isotope Au198 was chosen. It was produced in the Brookhaven pile by means of the reaction Au197 + n ? Au108. It decays by ß emission (0.96 mev) to Hg108 with the subsequent emission of a y ray (0.41 mev). 70Au 108 ? 80Hg 108 + -1e°. The half life of the Au108 is 2.7 days so that a strict time schedule had to be maintained in order to secure sufficient activity until the end of the experiments. For this reason, initial activities as high as 10,000 millicuries per gram were used. The gold arrived in the form of foil and was evaporated onto one face of each gold specimen cylinder to a thickness of about 100A. A sandwich-type specimen was formed by welding two such cylinders together. Evaporation of Gold: The gold was evaporated under vacuum from heated tantalum strips which were bent in such a way as to limit the solid angle through which the gold was allowed to vaporize, thus insuring a more efficient utilization of the gold. The specimens rested on flat brass rings which had an inner diameter of 0.475 in. The entire specimen-holding assembly could be manipulated from outside the vacuum system by means of a magnet which attracted a slug of soft iron attached to the assembly. By evaporating inert gold on glass slides under conditions identical to those employed for the radioactive gold, it was found that the thickness of the films was about 100A. Welding: The welding was performed by hot pressing in a stainless steel cylinder. The inside of the cylinder was threaded and fitted for two plugs. The specimens to be welded were placed in the middle of the cylinder and two pressing disks, one at each end, were inserted to avoid shearing stresses as the plugs were tightened. Mica disks were placed between the pressing disks and the specimens to prevent them from welding. The plugs were then tightened with a hand wrench and the entire unit was placed in an argon stream for about an hour to remove the oxygen. The unit was then inserted in the center of an argon atmosphere furnace maintained at about 700°C and left there for about an hour. Because of the difference in the temperature coefficient of expansion of the two metals, as the temperature rose. the pressure on the specimen-rollple increased and a weld resulted Welding was generally satisfactory under the conditions described.

Jan 1, 1955

By G. Pizzi, G. M. Ciucci, G. L. Chierici

The use of the material balance equation to estimate the volume of hydrocarbons originally present in a reservoir, whose producing mechanism is partly due to water drive, has been discussed in the literature by several authors. There is no general agreement upon the possibility of obtaining reliable results by this method. Gas reservoirs in contact with an active aquifer are considered in this paper. Theoretical considerations based on the cybernetic principle of uncertainty (which states that the internal structure of a system cannot be uniquely determined from its observed external behavior) lead to the conclusion that the volume of gas originally present in a reservoir of this type cannot be uniquely determined from its past history. The range of values which encompasses the actual value of the reserves varies from case to case and must be determined by either numerical or analogical methods. Results obtained for six gas fields are reported. All these fields were produced with small fluctuations in their production rates, as is common practice for gas reservoirs; no gas storage fields were considered. Results obtained show that reserves values in a range of 1 to 2, associated with appropriate aquifers, allow the matching of the reservoir past history with mean-square deviations less than the experimental errors involved in pressure and produclion measurements. Similar results have been found in several other partial water drive gas reservoirs. From these results it is concluded that gas reserves cannot be uniquely determined from the past performance of partial water drive reservoirs, at least in cases where the reservoir has been submitted to small fluctuations in the production rates, and pressure data of normal accuracy are available. INTRODUCTION A number of authors have analyzed the problem of estimating the reserves originally present in a partial water drive reservoir from its past pressure-production performance. Literature which deals with this subject can be grouped, according to their conclusions, as follows. 1. A reliable value for the reserves can be obtained even if reservoir data (pressure and cumulative production) are affected by errors within the normal range.&apos;-&apos; 2. A reliable value for the reserves can be obtained only if reservoir data are very accurate&apos;- or if past production performance has been subjected to abrupt variations in the production rate."&apos; 3. No unique value for the reserves can be obtained from reservoir past production performance. This conclusion has been based upon theoretical considerations" and verified in several field cases. The purpose of this paper, which deals only with partial water drive gas reservoirs, is to test the above conclusions against actual field cases. Some theoretical considerations on this problem are also presented. THEORETICAL CONSIDERATIONS As the behavior of a gas reservoir communicating with an aquifer depends on both the aquifer and the reservoir characteristics, the physical system to be studied is the combined gas reservoir plus aquifer. The information which is available for studying the performance of such a system is the well production rates and bottom-hole pressures, all given as functions of time. The external behavior of the reservoir-aquifer system is therefore described by 2n input variables (Gp, Wp,) and n output variables (p,), n being the number of wells in the reservoir. In reservoir engineering it is common practice to consider the reservoir as a whole, disregarding the internal distribution of pressures and of producing wells. This practice is equivalent to substituting the above multi-variable system with a single-variable system, where the average reservoir pressure is the only output variable and the cumulative production G,(t) and W,(t) are the input variables. The internal structure of such a system, defined by initial gas reserves G, aquifer shape and dimensions, boundary conditions and petrophysical parameters distribution throughout the aquifer, is unknown. Therefore, from a cybernetic point of view the system is a "black-box It has been demonstrated" that for a blackbox the indetermination principle holds. Accordingly, the number of different internal structures (or set of parameters) which can account for the observed external behavior is infinite. As a consequence, the initial reserves cannot be uniquely determined from the reservoir past performance. When W,(t) is known, the determination of G from

By Harrison R. Cooper

Measurement of process material composition with on-line instrumentation has commanded attention of metallurgical plant management as a logical extension of the sampling operation, making possible immediate determination of essential data needed to maintain efficiencies at the highest possible level. The current status of methods employed for online composition analysis of slurries and solid materials is reviewed.

Jan 1, 1984

By Y. C. Liu, R. H. Richman

From rolling textures of polycrystalline AgCl determined as a function of temperature, changes in the amounts of the individual textural components are correlated with temperature-dependent changes in glide geometry. The preferred orientations are influenced by the slip behavior as follows: 1) pencil glide, characterized by (110) slip directions and a greater participation in the deformation the higher the temperature, leads to a(012) fiber texture; 2) low-temperature deformation, primarily on (110) (110) systems, generates the {237}-(11, 9, 7) component; and 3) slip on {111}(110), comprising a significant portion of the room-temperature deformation, generates the {135}(211) and {110}(112) components. Typical re crystallization textures are also presented and briefly discussed. SPECIFIC relations between flow mechanisms in crystals and the individual orientations or components in deformation textures are necessary for a thorough understanding of the origin of such textures. Within each ordinary class of crystal struc- tures there is insufficient variety in the observed preferred orientations to permit direct and unambiguous correlation between flow mechanism and texture. A second approach to this problem is the correlation of textural changes with some known variation in glide geometry within one substance,1 In this paper, the latter approach is applied directly to a material in which there are distinct changes in the character of glide with changes in temperature. Silver chloride, although a nonmetal, is reported to exhibit slip,2,3 fiber textures,4 and rolling textures5,6 crystallographically similar to those of the well-studied fcc metals;7,8 in addition, there is a marked temperature sensitivity of the glide planes upon which flow occurs.3 Previous investigations of textures in AgCl unfortunately did not employ methods sufficiently sensitive to define possibly important minor components in the texture, nor did they utilize the temperature dependence of the glide systems. Thus, in order to clarify the effects of changes in slip mechanism, this paper reports a survey, using semiquantitative methods, of preferred orientations in rolled AgC1. Inasmuch as the influence of prior deformation texture upon preferred orientations after annealing is also of interest, some representative annealing textures are presented.

Jan 1, 1965

By Theron Wasson

The Central Michigan area held first place in the state during the year. Midland and Isabella, the leading counties in 1932, produced most of the oil in 1933. The Porter field southeast of Mt. Pleasant and along the same structural trend saw the greatest drilling activity. In Porter during the year 117 new wells were drilled. Under proration these wells produced 3,583,617 bbl., or nearly one-half the total for the state, which has been estimated at 7,947,695 bbl. The Porter field is already outlined on all sides except the northwest. It probably reached its peak in 1933. Unless a new field of some magnitude is developed in 1934, Michigan will see a continuous decline. The Greendale extension to the old Mt. Pleasant field furnished the new flush for 1932. In 1933

Jan 1, 1934

By L. R. Woodyatt, H. J. Beattie, C. T. Sims

Theories correlating the formation of u and related intermetallic compounds to the electron-per-atom density of binary and ternary alloys have appeared regularly in recent technical literature. These same principles can be modified and applied to complex precipitation-strengthened alloys such as the iron-, cobalt-, and nickel-base superalloys and the stainless steels. Since these complex alloys contain carbides and other phases that normally precipitate before the U-type phases, the nature and amount of the precipitated phases must be calculated first. The following general formula is then applied to the residual matrix composition of the alloy: element. The magnitude of the resulting number is indicative of whether the alloy will form a a -type phase. When these calculations (which are computerized) are systematically applied to alloys of knoun phase analysis, a breakoff in average electron-vacancy number is noted between U-free and U-prone alloys. Alloys with an average electron-vacancy number higher than the breakoff form a-type phases, while those with lower ones do not form these phases. This method could then be used to eliminate from consideration all experimental compositions that would precipitate undesirable phases. It also is useful in evaluating analyzed heats of alloys where minor heat-to-heat variations determine whether the alloy is o-free or o-prone. THE highly significant development of strong, ductile superalloys to provide reliable construction materials in the 1000" to 2500° F temperature range has been due principally to unremitting application of Edisonian techniques and logic by the dedicated physical metallurgists who have shouldered this responsibility. Tools such as the electron microscope, phase analysis, and computers to accomplish regression analyses have been used heavily, but the effort has been essentially practice of an art, rather than a science. The objective of this paper is to describe and illustrate application of some relatively fundamental principles to certain of these alloy systems in an attempt to remove some of the empiricism from the technology. Specifically, the work presented here deals with the use of periodic-group relationships to predict the formation of intermetallic phases which can occur in primarily austenitic (fcc) structures. Calculations that have been developed might be applied in the design of new alloys and the evaluation of known alloys, and thus have the potential of eliminating vast areas of unnecessary alloy preparation and evaluation. ALLOYING CONCEPTS AND STRUCTURAL FEATURES OF SUPERALLOYS Strength is produced in austenitic superalloys by three principle mechanisms: 1) precipitation of y&apos;; 2) formation of carbides; 3) solid-solution hardening by soluble refractory metals. The first mechanism requires the addition of aluminum and titanium, the second requires carbon and carbide-forming elements, while the third calls for the addition of molybdenum and/or tungsten. A considerable concentration of chromium is usually maintained to resist oxidation/corrosion, but it is also an important carbide-forming element. Fig. 1 shows a sketch and electron micrograph of the structure of a typical wrought nickel-base super-

Jan 1, 1967

By George A. Roberts, Arthur H. Grobe

Tensile, hardness and density properties are presented for a new 18-8 stainless steel powder for the —50, —100, and —140 mesh cuts and also for a prepared blend containing 62 pct —325 mesh powder. The data were obtained for sintering temperatures of 2100° to 2350°F and for compacting pressures of 30 to 50 tons per sq in. A NEED has existed for a stainless steel powder of uniform composition from particle to particle, which could be readily molded and sintered, and which would yield moderate to high strength and ductility when processed into parts by standard powder metallurgy techniques. The literature reveals that previously available powders have been lacking in one or several of these desirable characteristics. Originally attempts to produce stainless steel powder by blending and diffusing elemental metal powders were unsuccessfu1.l A truly alloyed stainless steel powder reported by Dale in 1947 yielded reasonable mechanical properties but required an exceptionally high sintering temperature of 2400°F in pure dry hydrogen.&apos; A later development reported in 1950 by Stern provided a stainless type powder of excellent molding properties&apos; but this powder likewise required sintering at temperatures over 2350 °F and did not yield properties as high as those previously reported. The powder was not truly alloyed prior to sintering. A prealloyed stainless steel powder has been developed that is readily moldable at 30 to 50 tons per sq in., can be sintered at low temperatures (2100" to 2300°F), and which yields compacts with both high strength and ductility. The powder is prepared by the liquid disintegration method," direct from molten metal. Early attempts to make 18 pct Cr, 8 pct Ni stainless steel powder by this method did not produce a usable powder for pressing and sintering because of a preponderance of spherical particles with relatively high, surface oxide content. It was learned that silicon additions to iron alloys, powdered by this process, gave bright powder of low-oxide content and such additions were made to 18-8 stainless with similar results. An attendant change in particle shape occurred reducing the number of spheroids materially. The optimum composition which has been studied and is reported here contains approximately 2.5 pct Si. Silicon additions to stainless steel of the 18-8 type improve the resistance to high-temperature oxidation and promote the formation of ferrite. Corrosion resistance is, however, controlled by chromium content and even though ferrite may exist the corrosion resistance is not generally impaired.4 Experimental Procedure A detailed study of the 18-8, 2.5 pct Si powder has been made in accordance with the following outline: 1. Four blends a. — 50 mesh b. —100 mesh

Jan 1, 1952

By H. E. Cline, T. H. Alden

A study zvas made of rate-sensitive plastic deformation and superplasticity in alloys of lead and tin. These alloys (lead, PO-19 pct Sn, Sn-38 pct Pb, Sn-2 pct Pb, tin) were extruded, aged at room temperature, or melted and resolidified to produce a variety of ~nicrostrnctures. Flow stress us strain rate data were obtained frorn tension tests for strain rates between 10-6 and 1 min-1. The curve log o .us log £ was S-shaped jor fine-grained materials and approxinzately linear for coarse-grained nzaterials. At constant grain size, the behavior was relatively insensitive to conposition. High rate sensitivity (d log o/d log k) and superplasticity occurred at intermediate strain rates in fine-grained materials and are believed to be associated with a transition with strain rate in the mode of plastic flow. This transition was shifted to higher strain rates with increasing temperataire or decrensing grain size. The high rate rneclzanisrn is presunzed to be slip, while rnetallographic evidence sug-gests that the low rate lnechanism is pain boundary sliding. PEARSON&apos; discovered that extruded eutectic alloys of Pb-Sn and Bi-Sn could be elongated as much as 2000 pct in tension. The ability for stretching decreased with aging time or annealing to increase the grain size. At high strain rates, or if the material was in the cast condition, normal ductility was observed. Following deformation of the extruded Pb-Sn eutectic at low rates, Pearson observed an equiaxed granular structure on an initially flat surface, while rapid straining produced elongated grains. He attributed the large deformation in the extruded alloys to the persistence of extremely small grains to a temperature sufficiently high for inter granular flow. Avery and backofen2 measured the strain rate sensitivity of the flow stress, m = d In old In 6, in the Pb-Sn eutectic and established a correlation between m and the tensile elongation. In the extruded eutectic alloy the strain rate sensitivity was 0.1 to 0.2 at rapid rates and the elongation was small, while at low rates m increased to 0.4 to 0.6 and superplastic elongation was observed. They also noted a grain size effect. In the case of the cast Pb-Sn eutectic the strain rate sensitivity remained at 0.1 over the range of strain rates of their experiment (3 x 10"3 to 2 min-I). These authors suggested that diffusional (Nabarro-Herring) creep was the mechanism by which deformation occurred at low strain rates, while climb-controlled creep occurred at high rates. Two predictions of this model are that, at low strain rates, the strain rate sensitivity approaches 1, i.e., Newtonian viscosity, and that the strain rate at constant stress varies as D/L2, where D is the coefficient of self-diffusion and L the grain size. More recently, a mechanical and microstructural investigation of the dilute superplastic alloy, Sn-5 pct Bi, has been done.3 The results show that the high strain rate sensitivity is associated with a transition with strain rate of the mechanism of plastic flow. At low strain rates, grain boundary sliding and its associated accommodation processes were evident, while at high strain rates quasi-uniform slip was concluded to be the dominant deformation process. The following experiments were performed to extend our knowledge of the phenomena of superplasticity to a larger range of strain rates, compositions, temperatures, and microstructures in the Pb-Sn alloy system. The question of why a cast structure does not exhibit viscous behavior although it appears to have a fine microstructure2 was investigated.

Jan 1, 1968

By Richard Akerman, Frederick Prime Jr

[THE attention now being paid both in this country and Europe the greatest economy in the working of the blast furnace, and the eagerness with which all thoughtful men in the iron business look for any new information which will tend to throw light on this subject, is a quite sufficient excuse for presenting this paper to the American Institute of Mining Engineers.] I. It must be borne in mind that when two bodies unite to form a chemical compound, heat is almost always evolved. In order to

By S. Weissmann, P. R. Swann, D. F. Wriedt

The sizes and density of precipitates in an intemally oxidized 0.19 wt pct Al-Ag single crystal have been determined by low-angle X-ray scattering and by transmission electron microscopy . The correlation in particle sizes measured by the two techniques is reasonably good. For an oxidizing temperature of 800°C the particles were found to INTERNAL oxidation of dilute alloys of aluminum in silver produces an oxide which has an excess of oxygen compared to Al2O3.&apos; It is believed that the excess oxygen is an indication of the small sizes of the oxide particles. Depending upon the particular model chosen for the oxide structure, the size of the o-A1 particles can be calculated as a function of the oxygen-to-aluminum ratio. These calculations pre- have diameters in the range 30 to 140A, with a mean size of about 50.4 as observed by electron microscopy. At lower oxidizing temperatures, less than 600°C, no clearly resolved particles are formed, and it is suspected that if A1-0 clusters exist they must be exceedingly small, i.e., 10A or less in diameter. dicto that the particles would vary in size from 15 to 100A. This range of sizes is amenable to detection by both small-angle X-ray scattering and transmission electron microscopy. This paper compares the cluster sizes in such internally oxidized A1-Ag alloys determined by transmission electron microscopy and small-angle X-ray scattering. SPECIMEN PREPARATION Single crystals were prepared from 99.9999 pct Ag, obtained from Cominco Products, and 99.99 pct Al, obtained from Aluminum Co. of America. All melting operations were carried out in graphite molds under flowing purified hydrogen in a horizontal zone refiner. The silver was first degassed,

Jan 1, 1964

By E. A. Smith, E. R. Parker

METALLURGISTS and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applications and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. Single-crystal copper specimens were broken in tension at impact velocities up to 100 ft. per sec. The distribution of slip bands in the fractured crystals was found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. EXPERIMENTAL PROCEDURE Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were made into test bars by sliding threaded steel bushings over each end of a crystal and then flowing silver solder between the crystal and the bushing. The inside diameter of the bushings was slightly greater than the diameter of the crystals, to allow space for the silver solder. The bushings were placed so that the gauge length of the crystals was one inch. The assembly is shown in Fig. I, with two views of a fractured crystal. Annealed polycrystalline copper bars of similar shape were machined from solid stock. X-ray measurements were made on all single crystals to determine their orienta¬tions. The results are shown in Fig. 2, where the location of the axis of each specimen is indicated on a standard projection. The bars were broken in a commercial variable-velocity tension im¬pact machine, which has been described in detail elsewhere.7,8 The stress and strain were recorded by means of wire strain gauges and a special commercial oscillo-raph, also described in detail elsewhere.9,10 The equipment and method can be briefly described as follows. The impact machine consists of a motor-driven flywheel containing a two-pronged hammer. This hammer is held retracted in the flywheel

Jan 1, 1944