Search Documents

By Howard R. Keil

Reactor at Carlton mill successfully calcines pyrite-telluride flotation concentrate for cyanidation. CARLTON mill in the Cripple Creek district, 45 miles southwest of Colorado Springs, Colo., has been in operation for approximately three years, treating the custom sulpho-telluride ores formerly handled by the Golden Cycle mill in Colorado Springs. At the new mill the pyrite-telluride flotation concentrates have been roasted, prior to cyani-dation, in a Dorrco FluoSolids reactor, which has proved capable of yielding calcine readily amenable to cyanidation. Incoming ores are crushed at Carlton to % in. and sampled in 30 to 75-ton lots before the individual lots are mixed in the fine ore bin. The composite ore then goes to the grinding circuit. Classifier overflow from the grinding circuit is treated by flotation to produce a concentrate containing approximately 85 pct of the values in 5 pct of the weight. The flotation concentrate goes to the FluoSolids reactor prior to cyanidation. Cyanide solution values are recovered by zinc dust precipitation. Flotation tailings are thickened and cyanided, the values from this part of the circuit being recovered from solution by activated carbon. Gold values in the flotation concentrates consist of a small amount of finely divided metallic gold; the tellurides, sylvanite and calaverite; and gold very intimately associated with the pyrite. The metallic gold and a part of the telluride values can be extracted from the concentrates by cyaniding without roasting. However, extraction on the tellurides by this method is not satisfactory, and the pyrite values are so intimately associated with the pyrite that very fine grinding and cyanidation for a prolonged period under ideal laboratory conditions does not yield good recovery. Upon roasting, the tellurides are oxidized to very finely divided metallic gold which is readily soluble in cyanide. The pyrite is oxidized mainly to a porous iron oxide which allows cyanide solution to penetrate to gold particles and take them into solution. Feeding the Reactor Flotation concentrates move by gravity to a thickener. Thickener underflow is discharged at approximately 60 pct solids, by means of a diaphragm pump, into a storage and blending agitator. From here the concentrates are pumped to a disc filter. The filter cake, at 84 to 88 pct solids, drops directly into a repulper where it is repulped into a slurry of 78 to 80 pct solids. The repulped filter cake flows into a 6x6-ft slurry agitator from which it is fed directly into the reactor by the Moyno pump. The Moyno pump has eliminated a large number of difficulties that were first encountered in feeding a wet concentrate to the reactor. On the original installation in Canada a screw feeder was used to introduce the filter cake directly into the reactor. Since the reactor is under a slight positive pressure it was necessary to have a suitable seal to prevent gas escaping from the reactor at this point. When the concentrates produced in flotation were coarse or granular they could be readily fed to the reactor but when fine-textured, clayey concentrates were produced a great deal of trouble was encountered.

Jan 1, 1955

By R. M. Hardgrove

PULVERIZED coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the difficulties incident to the burning of coal. In a cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverized in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. PROCESS OF BURNING CEMENT CLINKERS The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output. This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,1 in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. WET VS. DRY PLANTS The study presented here covers 88 plants, of which 41 are wet and 47 dry. Of

Jan 1, 1941

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By R. A. Deju, R. B. Bhappu

Further information on the surface characteristics of the silicate minerals was obtained by experimentally correlating the oxygen-silicon ratio of the silicates with their electrokinetic properties. Specifically, the behavior of the minerals in an electric field was investigated using zero point of charge as a parameter. A modified electrophoresis cell was used for the determination of electrophoretic mobilities. It was shown that there is an increase in the zero point of charge with increasing oxygen-silicon ratio in the silicates. Finally, a chemical interpretation was presented to describe the surface phenomena observed in the experiments. In recent years great interest in surface chemistry has produced a number of methods to study the surfaces of minerals and to observe the phenomena occurring at their interfaces. One such method is discussed in this paper. A rather complete review of the surface characteristics of the oxide minerals has been undertaken by parks,' but, a similar study has not been made for the silicate minerals. Two previous papers by the authors2'3 attempted to remedy this situation. In these papers it was demonstrated that the reaction between the silicate mineral particles and acidic water involves mainly an exchange of metal ions for hydrogen ions on the surface of the solid, leading to an increase in pH of the aqueous phase. Also, the degree of reaction was found to depend on the oxygen-silicon ratio of the silicate structure, being least for the quartz and greatest for the olivines. A hypothesis was then set forth explaining that upon the fracturing of a silicate mineral, the oxygen-metal bond (which is almost entirely ionic in character) will break more easily than the stronger oxygen-silicon bond. This results in the exposure of unsatisfied oxygen sites on one hand and active, exchangeable cations on the other. These active sites on the fractured surfaces are then available for reaction with the hydrogen ions in acidified aqueous solution. Thus, an increase in degree of adsorption of hydrogen ions occurs as the oxygen-silicon ratio increases due to the presence of a larger number of active sites on such minerals. A correlation between oxygen-silicon ratio and electrokinetic properties will be further pursued in this paper from both the theoretical and experimental points of view. Efforts will then be made to present a chemical interpretation of surface phenomena observed in the experiments. It is believed that this study may supply pertinent information on the behavior of silicate minerals in froth flotation systems. ELECTROKINETIC STUDIES Equipment: In a previous paper,2 Deju and Bhappu described a simple method for determing the zero point of charge using a potential across a cata-phoresis cell and observing particle movement by means of a Rayoscope* optical system. This setup is simple in design and operation and extremely reliable. With care, reproducible results within 1.5% accuracy may be obtained. A new setup has been developed, based partly on the design by Zeta-Meter Corp.4 and partly on previous cells used at the New Mexico Bureau of Mines. This new, modified cell is shown in Fig. 1. Although

Jan 1, 1967

By R. M. Hardgrove

PULVERIZED coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the difficulties incident to the burning of coal. In a cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverized in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. PROCESS OF BURNING CEMENT CLINKERS The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output. This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,1 in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. WET VS. DRY PLANTS The study presented here covers 88 plants, of which 41 are wet and 47 dry. Of

Jan 1, 1941

By M. A. Mayers, J. A. Thompson

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By J. A. Thompson, M. A. Mayers

IN recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.1-14 Only in Russell's method11 and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce-the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼ in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C. consisting of two annuli of 0.011-in. (0.28-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By J. A. Thompson, M. A. Mayers

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By Jeffrey L. Thompson, Kenneth A. Gutschick, Robert C. Freas, Robert S. Boynton

Lime, the "versatile chemical," is, generally speaking, a calcined or burned form of limestone commonly known as quicklime, calcium oxide or calcia, or, when water is added, calcium hydroxide or slaked lime. Almost 40 different lime products are available, a fact which has contributed to the rather loose use of the term lime as well as to much confusion and misunderstanding. The term is frequently, albeit erroneously, used to denote almost any kind of calcareous material or finely ground form of limestone or dolomite. Lime is usually made from high-calcium or high-magnesium limestone, generally having a minimum of 97% combined carbonate content. Normally, high-calcium limes contain less than 5% MgO. When the lime is produced from a high-magnesium limestone, the product is referred to as dolomitic lime. Calcination, or the production of lime, has its origins in the earliest days of alchemy, with the general reaction class having been identified in an Arabic text printed in 1000 A.D. It was much later, however, in the mid-1700s to the mid-1800s before this basic reaction became understood from a scientific perspective. The production of lime has been so basic and simple that its underlying scientific principles have over the years received only intermittent investigation. Rather, much of the thought and inquiry has been directed toward the development of kilns. Thus, it has only been in the last 15 to 20 years that lime has received any concentrated scientific investigation relative to the thermodynamics and kinetics of the calcination and hydration reactions. Calcination refers to a broad class of reactions, of which the lime/limestone reaction is just one, wherein a substance is heated to less than its melting point, resulting in a weight gain or weight loss. In the calcination of limestone to produce lime, the basic chemical reaction is as follows: [CaCO3 (limestone) + heat (1000° to 1300°C)= 100 CaO (quicklime) + CO2 T 5644 or CaCO3 • MgCO3 (limestone) 10084 + heat (900°C to 1200°C) CaO • MgO (quicklime) + 2CO2 T 56 4088] While there is nearly universal agreement about the equilibrium conditions related to the limestone/lime reaction above, there have been numerous and varied calcination models developed for the reaction. Recent investigations have resulted in the development of the model shown in Fig. 1. From this model it can be seen that calcination is a function of both temperature and CO2 pressure. It does not, however, provide any indication of the rate at which the reaction takes place. Calcination is strongly time variant with different limestones. In a very broad sense this relates to the fact that the calcination reaction starts on the exterior surface of the limestone and then proceeds toward the center. As the calcination reaction takes place, the CO2 released at the reaction interface must make its way through the lime to the exterior surface. Therefore, because calcination is limited by gas diffusion to the surface of the partially calcined limestone, natural impurities in the stone, differences in crystallinity, grain boundary chemistry, density variations, and imperfections in the atomic lattice all play a significant role in

Jan 1, 1983

By Frank H. Macpherson

Few people realize the tremendously important part that Saline and Pulaski Counties in central Arkansas have played in the winning of the war The present favorable war situation might have been very different if we had not had the bauxite produced during the past two years from these two small areas, a total Of about 15 square miles. As a general statement, it can be said that the Arkansas bauxite deposits are, individually, relatively small, irregular in thickness, somewhat scattered and, therefore, compared with coal or iron-ore or open-pit copper deposits, relatively ill adapted to a rapid and drastic expansion in output. A few years ago it would have seemed an impossibility for these two counties to produce over six million long dry tons of bauxite in one year. However, with the cooperation of the operators, that is what happened in 1943, when the state of Arkansas achieved the seemingly impossible with a production of 6,020,684 1 long tons (dried equivalent) of bauxite ore during the calendar year, compared with an average annual production of 323,7252 tons in the period 1931 to 1941. It became apparent early in the year '94' that the united States soon might be drawn into the war, and, therefore, that an immediate study of the domestic metal situation was necessary. Aluminum is by far the most important metal used in the manufacture of aircraft and many other implements of war and it was evident that there would have to be a tremendous increase in the domestic production of bauxite, which is practically the only present source of this metal. AS more than 95 per cent of the known bauxite reserves of the United states was in Arkansas, careful preliminary studies were made in that state by representatives of the united States Bureau of Mines, the United States Geological survey and the War Production Board in the summer of 1941 Reserves in other states also were studied. The result of these studies was a recommendation by the War Production Board that mining in the bauxite.producing areas of Arkansas be geared for maximum production, in order to supply sufficient ore for this country's war requirements and, if necessary, to supply the war needs of Canada as well. The annual goal of eight million long tons (dry weight) set for Arkansas by the war Production Board was exceeded in 1943, when in August the output reached a rate equivalent to more than 8,300,000 long tons, dry basis. Because of the comparatively small tonnage of bauxite reserves, Congress appropriated funds for an extensive drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. Drilling began in May 1942 but owing to delay in delivery of drills, and trucks upon which the drills were mounted the program did not get into peak operation until early in 1943. By the end of July 1944, the Bureau of Mines records indicated an addition to the Arkansas reserves of 10,000,000 long tons (wet basis) in place,

Jan 1, 1946

By Frank H. Macpherson

FEW people realize the tremendously important part that Saline and Pulaski Counties in central Arkansas have played in the winning of the war. The present favorable war situation might have been very different if we had not had the bauxite produced during the past two years from these two small areas, a total of about 15 square miles. As a general statement, it can be said that the Arkansas bauxite deposits are, individually, relatively small, irregular in thickness, somewhat scattered and, therefore, compared with coal or iron-ore or open-pit copper deposits, relatively ill adapted to a rapid and drastic expansion in output. A few years ago it would have seemed an impossibility for these two counties to produce over six million long dry tons of bauxite in one year. However, with the cooperation of the operators, that is what happened in 1943, when the state of Arkansas achieved the seemingly impossible with a production of 6,020,684 1 long tons (dried equivalent) of bauxite ore during the calendar year, compared with an average annual production of 323,725 2 tons in the period 1931 to 1941. It became apparent early in the year 1941 that the United States soon might be drawn into the war, and, therefore, that an immediate study of the domestic metal situation was necessary. Aluminum is by far the most important metal used in the manufacture of aircraft and many other implements of war and it was evident that there would have to be a tremendous increase in the domestic production of bauxite, which is practically the only present source of this metal. As more than 95 per cent of the known bauxite reserves of the United States was in Arkansas, careful preliminary studies were made in that state by representatives of the United States Bureau of Mines, the United States Geological Survey and the War Production Board in the summer of 1941. Reserves in other states also Were studied. The result of these studies was a recommendation by the War Production Board that mining in the bauxite-producing areas of Arkansas be geared for maximum production, in order to supply sufficient ore for this country's war requirements and, if necessary, to supply the war needs of Canada as well. The annual goal of eight million long tons (dry Weight) set for Arkansas by the War Production Board Was exceeded in 1943, when in August the output reached a rate equivalent to more than 8,300,000 long tons, dry basis. Because of the comparatively small tonnage of bauxite reserves, Congress appropriated funds for an extensive drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. Drilling began in May 1942 but owing to delay in delivery of drills, and trucks upon which the drills were mounted, the program did not get into peak operation until early in 1943. By the end of July 1944, the Bureau of Mines records indicated an addition to the Arkansas reserves of 10,000,000 long tons (wet basis) in place

Jan 1, 1945

By A. S. Emanuel

A correlation has been developed for calculating the phase behavior of, gas-condensate systems at reservoir conditions. The correlation is based on the principle of corresponding states and has been coded for an IBM 7094. Experimental K-values were determined for several gas-condensate systems at reservoir conditions to evaluate various semi-empirical parameters of the correlation. The approximate range of application of the correlation is 150 to 300F and 1,500 to 6,000 psi. INTRODUCTION The rapid development of digital computers during the past several years has made feasible the calculation of hydrocarbon phase behavior by methods based on rigorous thermodynamic principles. Good correlationsl have been developed for low to moderate pressures, but these techniques have not yet been extended successfully to reservoir fluids at high pressures. Consequently, the determination of phase behavior of oil and gas systems at reservoir conditions is still based almost entirely on generalized data correlations or on experimental studies of the fluid in question. While these methods have been used successfully many times, they do have inherent limitations that restrict their applicability. Generalized correlations, such as the NGShlA K-charts, are limited to the range of pressure, temperature and components for which the data were determined. The accuracy of these correlations is often questionable because the effect of total system composition is not well defined. Experimental studies offer a reliable method for determining phase behavior, but usually the studies are costly and time consuming. Recently, Leland and co-workers presented a new approach to calculating phase behavior from the principles of corresponding states.6-8 Corresponding states methods determine the thermodynamics properties of a given system by comparison with a reference substance whose properties are known. The accuracy of this approach depends on close chemical and structural similarity between the reference substance and the system in question and between components within the system itself. For high accuracy, it is usually necessary to correct for chemical and structural dissimilarities. In principle, however, the corresponding states method should be no less accurate at high pressures than at low pressures, provided reference substance properties are known. This paper describes an empirical modification of the basic correlation proposed by Leland, et al.6 for the specific purpose of calculating the phase behavior of gas-condensate fluids at reservoir conditions. The modified correlation, which has been programmed for an IBM 7094, may be used for either approximate or precise determination of fluid behavior depending on the amount of analytical and, experimental data available for the system. BASIC THEORY The basic theory of the corresponding states phase equilibria correlation was first published by Leland, Chappelear and Gamson.6 Subsequently, Leland, Chappelear and Leach published methods for improving the accuracy of the original theory.7-9 The aim of the correlation is to calculate the K-value of each component of a given system as a function of pressure, temperature, and over-all composition, where Once the K-values are known, the phase behavior may be determined directly by an appropriate flash calculation. The basic equation for calculating component K-values was taken from the work of Joffe. 4 For any component i of a mixture, the K-value is given by

Jan 1, 1969

By D. E. Hawk, R. F. Burdyn, F. D. Patchen

Earlier work on a mud separator for barite recovery is extended to the design and construct ion of a rugged field unit. Problems associated with scale-up for field use include the me of dilution water and its effect on capacity, power requirements and pressures developed. Equations for these quantities are derived and applied in maximizing the beneficial effects of dilution and minimizing the power required. Tests on the full-size rotor show that its performance can be predicted by theory. The completed unit is compact and lighter than current decanting types. Its capacity is from 10 to 22 gal/min with corresponding barite recovery efficiencies of 92 to 86 per cent. INTRODUC'TION In an earlier publication a new type of centrifugal device was described for solid-liquid separations.l In that paper an operating equation was derived, and its validity demonstrated in laboratory scale experimentation. Some of the features apparent in this new device seem particularly well suited to the conservation of barite in field drilling-mud systems, hence the development was extended to the design and construction of a field unit. In the present paper the design problems associated with scale-up are considered. A full-scale, rugged self-contained field unit is described, and test results discussed which verify that the performance of the large field unit can be described by a simple operating equation. PRINCIPLE OF OPERATION OF SEPARATOR In principle, the new device is simply a perforated cylinder rotating within a body of fluid which is contained within a stationary case, as in Fig. 1. The frictional drag generated by the rotating cylinder causes part of the fluid to rotate. At the surface of the cylinder, assuming no slip occurs, the angular velocity of fluid and of the cylinder are identical. If there are suspended particles present of greater density than the fluid, the centrifugal force acting on these particles causes them to move radially away from the cylinder at some velocity vp . Where the Stokes settling equation holds, this velocity may be expressed as:2 d2 ?p rw2 If the case is provided with openings at both ends, a suspension can be pumped in at one end at a fixed rate. Part of the suspension can then be removed at a fixed rate at the other end of the case as underflow, and the remainder forced through the perforations and hollow shaft of the rotor to appear as effluent, also at a fixed rate. The radial component of the flow velocity of this stream as it reaches the rotor surface, is simply effluent flow rate divided by cylindrical surface area: Because up is a function of particle size, for some particular particle size, the velocities vp and v, will be equal in magnitude. This is defined as the critical particle size and represents the size above which all particles appear in the underflow and below which all particles appear in the effluent. For this equilibrium condition at the rotor surface, Eqs. 1 and 2 combined give

Jan 1, 1966

By Thomas O. Ziebold, Robert E. Ogilvie

Experimental analysis of diffusion samples covering the entire Cu-Ag-Au system at 725°C has been carried out. Experimental coefficients are computed at twenty-eight points in the lermary system. It is found that the direct coefficienl for copper is nearly independent of the silver, content for 1ow-silver alloys and that the cross coefficient for silver correlates with the ther-nzodynatnic properlies. This lalter observalion leads to the conclusion that the mobililies of copper and gold are nearly equal. Thermodynarmic actiuilies for Cu-Ag-Au were computed from binary data and adjusted to be consistent with neasured tie lines across the two-phase region which extends into the ternary diagram at 725°C. Application of these therknodynarnic calculaliorls to the dijftcsion data terifies the Onsager reciprocal relations to the extent that experimental uncertainlies will allow. It is jound that diffusion neav the critical point of the 1200-phase field in the isothermal section at 725°C causes the composition gradients for copper and silver to approach infinity while the direct and cross coeficients become equal. From the standpoint of experimental Procedures, it has been shown that microanalysis of ternary samples may be carried out using a simple expression for the conversion of X-ray zntensily to composilion. The accuracy of' this method has been demonstrated by the analysis of standard alloys and by the reproducibility of composition determinations using differed X-ray lines. DIFFUSION in a ternary alloy system is basically and significantly different from diffusion in binary alloys. When only two elements are present there is just one independent composition variable, and the diffusion profile of composition vs distance across a sample must change monotonically through all solid solutions bracketed by the terminal alloys. If two-phase regions are stable for compositions between the terminal values, these must appear as planar interfaces in the diffused sample, with the composition profile exhibiting sharp discontinuities. Adding a third element may alter this picture completely. Because of the additional degree of freedom in the composition, we may see composition profiles which do not change monotonically through solid-solution ranges, and stable, nonplanar phase interfaces. Even though two-phase regions may lie between the terminal compositions of a diffusion sample on the constitution diagram, they will not necessarily appear in the diffusion profiles. In binary diffusion only one coefficient is needed to describe the interdiffusion process. From Fick's law this coefficient relates the diffusive flux of one component to its own composition gradient. In ternary diffusion we must allow for cross interaction between the two independent species. By a linear extension of Fick's law we introduce "cross" or "off-diagonal" diffusion coefficients which relate the flux of one component to the composition gradient of the other independent constituent. Thus, we require four interdiffusion coefficients to describe the transport process in a ternary system. In its most general form,1,2 the rate equation for mass transport by isothermal diffusion in a system of s components states that the diffusive flux of component i, Ji, is a linear summation of all driving forces, Xk, each force being multiplied by an appropriate compliance coefficient:

Jan 1, 1968

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By H. S. Price, R. L. Reed, J. E. Warren

The behavior of the reverse-combustion process in a linear adiabatic system is theoretically investigated by means of an idealized physical model. T his model is described by a pair of non-linear equations involving heat and mass transfer which are coupled by a concentration-dependent reaction-rate function of the Ar-rhenius type. The differential equations governing the quasi steady-state temperature and concentration distributions are approximately solved by using either physical or mathematical simplifications. It is shown that the reverse -combustion process can be mechanistically described by simple physical models whose behavior equations can be solved formally. It is further demonstrated that the derived reverse-combustion equations can be solved numerically within the error limits for the experimental data. The theoretically predicted peak temperature-flux-velocity relationship exhibits reasonable agreement with experimental data obtained from Athabasca tar sand. The principal contribution of this work lies in its usefulness as a starting point for developing a more comprehensive theory. A description of the vaporization-coking process must be obtained; then, the theory must be extended to three dimensions to include geometrical effects and heat losses. INTRODUCTION In another paper,'" he physical processes visualized as occurring during reverse combustion have been described. In this paper, the extent to which an elementary theory can account for experimental observations is determined. Theoretical results that can be used to estimate some of the behavior characteristics of importance to this process are also presented. Since it is not possible to include all the features of the combustion mechanism of which we are currently aware, the mathematical formulation refers to the highly idealized system developed herein. This simplified physical model is based on the simultaneous transfer of mass and heat accompanied by a chemical reaction: it is described mathematically by a pair of coupled, nonlinear differential equations. Similar sets of equations have been studied extensively in the field of flame propagation; an excellent review of these investigations has been published by Evans.1 FORMULATION OF THE PROBLEM It will be recalled that the experiments are performed with a thin-walled cylindrical tube that is uniformly packed with sand and oil. The system is maintained substantially adiabatic by means of heat supplied externally in such a way that the radial temperature gradient in any plane normal to the axis of the tube approaches zero. Initially, the tube is at ambient temperature, except at one end where it is rapidly heated to a predetermined temperature. When the prescribed temperature is achieved, air is caused to flow into the cold end of the tube. As the oxygen in the air stream contacts the hot oil, a localized exothermic reaction takes place. The generated heat is conducted and convected away from the reaction zone so that definite temperature and concentration profiles are rapidly established and move uniformly in a direction opposite to that of the air flow (Fig. 1). As a consequence of this mode of oxidation, all of the oxygen in the air is consumed; then, the remaining nitrogen and the gaseous combustion products sweep out all vaporized hydrocarbons and leave an immobile hydrocarbon-coke on the sand.

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By J. T. Mackenzie

HENRY MARION HOWE, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: "Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up-by masses of graphite . . . " Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in 1900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on 'The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro- structure of the metallic matrix, Professor Howe pointed out that "such minor struc- tural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By J. H. Schulman, M. H. Buckenham

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963