Search Documents

By L. A. Schrider, J. A. Wasson

A method of predicting waterflood performance has been developed that combines certain facets of several previously published prediction techniques. The manner of combination has required the development and use of some new and some little-known relationships and has eliminated several of the weaker assumptions inherent in the original individual prediction methods. This approach, which was designed for computer solution, has removed the necessity of referring to plotted curves and permits the analytical prediction of water flood performance for a five-spot well pattern in either homogeneous or stratified reservoirs. The Predicted values are expressed in common oilfield units rather than in abstract or dimensionless terms. The calculation procedure has been programmed in FORTRAN IV and the entire program listing is available to potential users.* Introduction Prior to initiation of secondary recovery of oil by waterflooding, the possibilities of economic success or failure must be evaluated with the greatest practical accuracy. Although many prediction techniques are available, most, if not all, have serious limitations. In recent years, the Bureau of Mines has attempted to stimulate interest in the secondary recovery of oil from Appalachian pressure-depleted reservoirs. Waterflooding, because of its widespread acceptance and success, is the principal secondary-recovery method considered. During the life of the project, several performance prediction methods have been studied and applied. Because these methods, individually, have inherent assumptions and limi-tations, portions of some of them have been selected and combined in an effort to eliminate such shortcomings wherever possible. We believe that the resulting technique is as accurate as the necessary available data will permit and that it has several distinct advantages over previously published methods. Development of the Method The fractional flow equation developed by Buckley and Leverett' from Darcy's law is the fundamental mathematical statement describing immiscible fluid-fluid displacement in porous media. A generalized form of this relationship, whose derivation is readily available in the literature, is The formation dip, a, is usually very small in those petroleum reservoirs being considered for pattern waterflooding in the Appalachian area. Therefore. in many cases. a has an almist negligible value. In addition, Ap, the difference between the density of water and the density of oil, is relatively small. For these reasons the gravitational term may often be neglected. Capillary pressure is a function of saturation, which is in turn a function of distance from the upstream boundary of the system or the injection well. In this study it is assumed that the frontal zone of the waterflooding (or zone of capillarity) has negligible length and that only those saturations in the water-swept zone at breakthrough and later are of interest. As the distance in a waterflood pattern is comparatively large and the change in water saturation with distance is usually small, the change in capillary pressure with distance is negligible. The simplified form of the fractional flow equation is appropriate, therefore, in this application. Three variables must be considered in determining that fraction of the total fluid flow that consists of water: the viscosity ratio, saturation, and relative permeability ratio.

Jan 1, 1969

By P. L. Allsman

A method of analyzing blasting action indicates that major cost savings are possible by revising practice and bringing the classical blasting formulas up to date; difficult problems such as taconite and throw-breakup can be attacked by engineering Denonation pressure — the peak pressure developed by the explosive reaction; "shatter blasting." Average detonation pressure — the average pressure over the time the reaction continues; "heave blasting." Radial presswe — the stress in a radially expanding sphere about the detonation. Corresponds to the diminishing peak pressure. Lateral stress - the stress in a circumferential direction, induced by outward movement of the rock away from the detonation. Limiting stress or Slim— the rock property at which failure will occur in the case at hand; may be tensile or compressive strength, or combinations. Recent developments in explosives technology, following the advent of nuclear explosions, have led to a rather complete understanding of their action. A survey was made for the purpose of uncovering any knowledge which might be applicable in the mining and quarrying industries, the principal users of explosives. Although no revolutionary techniques have become apparent, much basic data pertaining to blasting — fortunately not classified — have been developed by recent research, from which a good general understanding of the process can be derived. It is hoped this explanation of the scientific principles governing explosive action, together with a proposed analysis of blasting practice, will further the development of mining engineering. NATURE OF THE REACTION: The phenomenon of explosion, termed detonation, is in reality a rather complex chemical reaction, and as such is completely explainable by physical and chemical laws. Detonation is characterized by high temperature and pressure, extreme rapidity — often being complete within one microsecond — and most importantly by formation of a shock pulse which accompanies the reaction zone. As with any chemical reaction, there is a critical value of temperature and pressure below which detonation can not occur; this is termed the "critical point". Whereas an explosive substance will decompose slowly at ordinary temperature, with the formation of gases which readily dissipate; at elevated temperature the reaction is considerably speeded. If pressure is suddenly applied at some point in an explosive medium, adiabatic compression results, and the temperature is locally raised. When the temperature becomes high enough the decomposition will be so rapid that the gaseous products do not have time to dissipate, but contribute to a further build-up of pressure. This, in turn, furthers adiabatic temperature rise over a widening area, and with any heat generated by an exothermic reaction, causes a rapid increase in temperature. Both temperature and pressure are spontaneously built up in this manner until the critical point is reached, resulting in detonation. The values of pressure and temperature necessary to create detonation are established by the unusual nature of the process. If temperature alone is raised above the critical point, without sufficient increase in pressure, deflagration or "low-order detonation" occurs. In the true, or "high-order detonation", the shock pulse resulting from the violent decomposition becomes an integral part of the reaction, and itself aids in increasing the detonation

Jan 1, 1961

Joseph G. Butler, Jr., who represented this Institute on the American Industrial Commission to France, has presented a report to the Chairman of the Commission regarding the steel industry of France in war time. In this report Mr. Butler calls attention to the fact that only a few steel works were visited and that he thinks it probable that there are many plants in France more up-to-date than these. He noticed especially in the plants visited a dearth of labor-saving devices and not very great attention to the safety of the employees. He also noticed that the whole of the iron and steel interests in France are being used at the present time by the Government for war purposes, and he was told on good authority that the production has doubled since May, 1915. When the war is over, it is thought that France can send large quantities of iron ore from Algeria to the United States and take in return American coal to France, an interchange which would doubtless be of mutual advantage. In Mr. Butler's opinion the shortage of coal in France may be overcome to some extent by the use of water-power and by electrical processes for steel manufacture, and lie believes when the war ends France will be able to compete with other countries in exports of general iron and steel products, this trade being facilitated by the port improvements at Bordeaux and Marseilles. The French labor situation is much better than that in the United States from the standpoint of labor unions, but the wages are less and many women are now being employed to do men's work. This has a tendency to keep wages low, but is probably a war expedient only. The cooperation among manufacturers in France is at a high level and both local and national organizations exist for the discussion and voicing of trade problems. The national body which is a combination of the individual organizations is the Comite des Forges de France and it is an interesting fact that many of the members of this body are office holders under the Government, or heads of Government Committees which are organized to look after the very business in, which the individuals are engaged.

Jan 12, 1916

By E. S. Shaw

Utah continues as a very unimportant factor in oil and gas production. During the year 1933 there were no developments of noteworthy significance. There were no completions of either producers or dry holes during the year. The only commercial production in Utah has been from the five fields listed in Table 1 and mentioned briefly in the following paragraphs. Virgin Field.—Oil was first discovered in 1907 in a well drilled in sec. 13, T.41S., R.12W. Of the first 15 wells drilled, all but three were failures. In 1920 production from four wells from 550 to 600 ft. deep was about 20 bbl. per day. San Juan Field.—The majority of drilling in this area was done during the years 1908 to 1911. Probably the first commercial well in the field was that drilled in NW.$i sec. 6, T.42S1 R.l9E., in 1909. Farnham Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1923. A number of years later a second well was drilled by The Carbon Dioxice a mica1 Co., the present operator, which markets the gas in the manufacture of "dry ice" and allied products. The eslimated production, as indicated in Table 1, includes 500 million cubic feet estimated to have been lost while drilling the discovery well. Cisco Dome.—The discovery well was drilled by The Utah Oil Refining Co. in November, 1924. The Crystal Carbon Co. markets the gas in the manufacture of carbon black. Ashley Valley Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1925. The Uintah Gas Co. markets the gas in Vernal, Utah, for fuel. Woodside Structure.—In February, 1924, gas was discovered in a well drilled by Utah Oil Refining Co. in sec. 12, T.l9S., R.l3N., on the Woodside structure. This gas is reported to contain an appreciable amount of helium. It is being held as a helium reserve by the United States Government. Salt Valley Structure.—The test of the Utah Southern Oil Co. in sec. 31, T.23S., R.21E., on the Salt Valley structure has been shut down for some time at 6120 ft. This test has passed through more than 5000 ft.

Jan 1, 1934

THE Joint Committee appointed to consider a Code of Ethics for Engineers recommends, after delib-erate consideration, that each participating Insti-tute or Society adopt the short simple Code of Ethics following this report. The Committee further recommends that the following method of interpreting and administering the Code be adopted by each participating Institute or Society after any necessary provisions have been, made in the Constitution and By-laws of the Organization. The President of each Society or Institute shall appoint a Standing Committee on Professional. Conduct, to administer the Code of Ethics. The duties of such a Committee shall be to interpret the Code and to render opinions on any cases of ques-tionable conduct on the part of members that may be submitted to the Committee. These interpretations shall be reported to the Executive Board of the Institute or Society who may approve these interpretations, or take such other action as may seem just and necessary. The reports of the Committee on Professional Conduct, when approved by the Executive Board, shall be printed in abstract and in anonymous form in the Institute's or Society's monthly journal for the instruction and guidance of fellow members. This Committee on Professional Conduct shall be appointed in each Institute or Society by the President holding office at the time of the adoption of this Code and shall consist of five member one appointed for five years, one for four years, a third for three years, a fourth for two years and a fifth member for one year only. Thereafter, the President then holding office shall appoint one member annually to serve for five years, and shall also fill any vacancies that may occur for the unexpired term of the member who has withdrawn. These appointments shall he made from among the older members of the Institute or. Society, so that advantage may be taken of their mature experi-ence and judgment. The Committee after appointment shall elect its own chairman and secretary. The Committee shall have power to secure evidence or other information in any particular case not only from the organization's own members, but if it should seem desirable, from men in other professions. The Committee may also appoint sub-committees to consider certain cases when deemed necessary.

Jan 3, 1922

By Graham John Mitchell

In May, 1919, a crosscut on the 1400-ft. level of the Briggs mine, a Calumet, & Arizona property at Bisbee, Ariz., penetrated a deposit of pyrite and chaleopyrite that had replaced quartzite and limestone and was cut, especially in the quartzite, by numerous fractures. As the drift advanced through these fractured portions, they were found to be free from copper-sulfate minerals although '(sooty" chalcocite was present in the fractures and also as coatings and replacements of pyritc. Howcver, sulfate soon made its appearance in certain fractures, filled them, and began to form stalactites. Several centers of incipient growth were noted for subsequent study, observations in the drift at frequent intervals during the past 17 months affording the opportunity of determining the rate of formation of the stalactites. The one to attain the greatest growth during the period of observation measured 27 in. long and averaged 1 in. in diameter. A close study showed it to be composed of small interlocked crystals of chalcanthite radiating from a small central tube-like opening. The trielinic form of the crystals was evident with prism and pinacoid faces recognixable. Assuming that the supply of copper-sulfate solution was constant (luring the 17 months—-and such an assumption is supported by the fact that the number of drops of excess solution falling, per minute, from the tip of the stalactite at the times of observation checked closely—thc stalactite, it has been estimated, grew at the rate of 1.58+ in. per month. DISCUSSION James I?. Kemp," New Yolk City.—J. S. Curtiss, in the monogr:tpll on Eureka, Ncv., say:: that a stalactite formed in limestonc grew 5/8 in. in three weeks and continued to grow as long as it had a drop of water or solution at the lower end. Another grew at the rate of 3/8 in. in the same time. In the case cited by Mr. Mitchell, the growth was about 136 in. in three weeks. A year ago we had an instance of the formation of cubes of galena on a railroad spike. A mine in northeastern Oklahoma had been idle about two years but on account of pumping of neighboring properties, the circulation of water was active throughout the drift. A cube of galena,

Jan 1, 1922

By Ellen H. Richards

It is of importance to analysts to have a ready means of detecting the presence of small quantities of titaninm in iron ores and in certain fluxes and slags. The method given in Elderhorst's Blowpipe Analysis (fusion with potassium hydrogen sulphate) requires considerable practice, in order so to regulate the heat that the titanium oxide shall become soluble. In Brash's Determinative Mineralogy is found a method which, at least in inexperienced hands, has given better results, i. e., fusion of the substance to be tested with sodium carbonate on charcoal in the reducing flame. The solution in hydrochloric acid of the bead thus obtained, boiled with tin or zinc, gives the characteristic violet color; but when the mineral contains less than four per cent. of titanium oxide, long boiling and consequent concentration is necessary. In fact the test would seem to be much less delicate than is generally supposed. In the course of some analyses I quite accidentally found that a peculiar color is given to turmeric paper by solutions of titanium chloride. This color is hard to describe, being modified by the quantity of ferric chloride present in the solution ; but it is neither the orange of zirconia nor the red of' boron. It is rather a dull shade of purple, arid is easily recognized when the paper is dried, although the color fades in a few hours. By this means a solution containing .015 per cent. of titanium oxide can easily be tested. The same solution, treated with tin, required to be concentrated to one-tenth its bulk before a decided color could be obtained. The color given to turmeric paper is intensified after the solution has been treated with tin. This and some other indications show that the best shade of color is given by the titanons chloride rather than by the titanic chloride, and no other salt of titanium than the chloride has been found to give the color. Another peculiar property of titanium salts has come tinder my observation. When titaniferous minerals are soluble in nitric acid, and the solution is subjected to the action of the battery, the soluble titanium salt is converted into the insoluble oxide and appears on the electrode, in some cases, as a white coating; this

Jan 1, 1883

By Ralph E. Esarey, G. F. Fix

The oil and gas industry in Indiana in 1938 showed considerable improvement over the preceding year. Most of the drilling and development during the year, as in the past several years, was in the Indiana portion of the Illinois Basin, but increasing interest was apparent in the old Trenton area, for possibilities of further production in the Trenton formation and the underlying St. Peter sandstone. Interest in all other portions of the state was at a new peak, since many areas have never been prospected. Natural gas production continued to drop during 1938, since new discoveries have not been able to keep pace with the rapid decline in older areas. Oil production increased considerably, chiefly through the discovery of new fields. Older fields contributed about the same quantity of oil during 1938 as during the preceding year. There were 159 wells completed in Indiana during 1938, an increase of 25 over the preceding year. Of these, 48 were oil wells, 41 were gas, and '70 failed to find commercial production. Forty-three, or about 20 per cent, were wildcat. Six of these were productive—three oil wells and three gas wells. Thirty-nine wells on which operations started during the year had riot been completed by Dec. 31. Fourteen others were temporarily abandoned, with the possibility that several will be drilled to completion in the near future. A new oil field (Heusler) was discovered in May 1938, in sees. 1 and 12, T. 7 S., R. 12 W., Posey County. Production was found in the Waltersburg (Upper (Chester) sandstone at a depth of approximately 1775 ft. At the close of the year, Heusler field had nine producing wells and two drilling. The Point township area, Posey County, near the confluence of the Wabash and Ohio Rivers, held promise of good production from the McClosky lime, but offsets to the, discovery well had only shows of oil. The discovery well declined rapidly in production arid was finally plugged. In the Oaktown field, Knox County, a wildcat came in with a good flow of gas, extending the field to the east, and proving considerably more acreage. A new gas area was discovered in Sullivan County, and four good wells were completed. The discovery well was in sec. 35, T. 8 N., R. 10 W., and had an initial

Jan 1, 1939

The cables brought the news last spring that the Institute had lost by death one of its most distinguished foreign members, Hjalmar Sjogren of Stockholm. For thirty-one years, Professor Sjogren had been one of our number. He was elected in 1891, joining the Institute at the time he was in the United States, in attendance at the Fifth International Geological Congress, which was held in Washington in the late summer of that year. Professor Sjogren was once more in America in 1906 and again in 1913, and on both of those visits his friends in New York had the welcome opportunity of extending courtesies to him. He was thus well known to a wide circle in our membership. His keen interest in the geology of iron ores brought him in touch with the many Americans who have studied them and who have been active in the important productive districts which he visited. Our Transactions contain (Vol. XXXVIII) one very important paper of seventy pages on the Geological Relations of the Scandinavian Iron Ores, which he contributed. Sten Anders Hjalmar Sjogren, to give his full baptismal name, was born June 13, 1856, and was the son of Anton Sjogren, a mining engineer, at the time in charge of the iron mines at Persberg, in the east and west iron-ore belt of central Sweden, about 160 miles west from Stockholm. The Persberg orebodies yielded magnetite and specular hematite from schists, with which limestones. were interstratified as well as the peculiar Swedish rocks called "halleflinte." The mines were also well known to collectors and students of minerals. While Hjalmar Sjogren was yet a lad, his father was advanced to the superintendency of a number of famous mining localities in this same district of Wermland. Paisberg, famous for its native lead, was one; and two others, Langban and Nordmarken, were among the most prolific sources of interesting minerals in all Sweden. In several localities, the pre-Cambrian limestones had obviously experienced the recrystallizing influences of intrusive igneous rocks and had been charged with the so-called "contact" minerals, which have found their way to the museums of the world. Anton Sjogren, the father, was a keen mineralogist and Hjalmar, the son, grew up in a favorable environment for receiving training and enthusiasms of the same sort. One is not surprised, therefore, to find Hjalmar Sjogren, in the long run, turning to mineralogy and geology as his final career.

Jan 1, 1923

By Ralph E. Esarey, G. F. Fix

The oil and gas industry in Indiana in 1938 showed considerable improvement over the preceding year. Most of the drilling and development during the year, as in the past several years, was in the Indiana portion of the Illinois Basin, but increasing interest was apparent in the old Trenton area, for possibilities of further production in the Trenton formation and the underlying St. Peter sandstone. Interest in all other portions of the state was at a new peak, since many areas have never been prospected. Natural gas production continued to drop during 1938, since new discoveries have not been able to keep pace with the rapid decline in older areas. Oil production increased considerably, chiefly through the discovery of new fields. Older fields contributed about the same quantity of oil during 1938 as during the preceding year. There were 159 wells completed in Indiana during 1938, an increase of 25 over the preceding year. Of these, 48 were oil wells, 41 were gas, and '70 failed to find commercial production. Forty-three, or about 20 per cent, were wildcat. Six of these were productive—three oil wells and three gas wells. Thirty-nine wells on which operations started during the year had riot been completed by Dec. 31. Fourteen others were temporarily abandoned, with the possibility that several will be drilled to completion in the near future. A new oil field (Heusler) was discovered in May 1938, in sees. 1 and 12, T. 7 S., R. 12 W., Posey County. Production was found in the Waltersburg (Upper (Chester) sandstone at a depth of approximately 1775 ft. At the close of the year, Heusler field had nine producing wells and two drilling. The Point township area, Posey County, near the confluence of the Wabash and Ohio Rivers, held promise of good production from the McClosky lime, but offsets to the, discovery well had only shows of oil. The discovery well declined rapidly in production arid was finally plugged. In the Oaktown field, Knox County, a wildcat came in with a good flow of gas, extending the field to the east, and proving considerably more acreage. A new gas area was discovered in Sullivan County, and four good wells were completed. The discovery well was in sec. 35, T. 8 N., R. 10 W., and had an initial

Jan 1, 1939

By Will Mitchell, T. G. Kirkland, C. L. Sollenberger

R. S. Handy (Santa Rosa, Calif.)—It would be interesting to learn the comparative results of treating the Korean scheelite ore described in this paper according to the following procedure: I—Follow the procedure described in the paper to the recovery of the sulphides by flotation. 2—Dilute the residue from the sulphide flotation strongly with water and disperse the contained colloids by adding a mixture of 75 pct sodium silicate and 25 pct quebracho to dispersion point. 3— Settle the dispersed pulp and decant the supernatant colloids. 4—-Dilute, settle, and decant the pulp until the settled residue is crystalline. Not over 10 pct of the tungsten minerals should follow the colloids. 5—Treat the settled residue by flotation, having established the proper pH. Oleic acid homogenized with cresylic acid or kerosene is more selective for scheelite than is oleic acid alone. (The recovery of the contained tungsten minerals should be practically complete in this operation.) 6—Deflocculate the tungsten concentrate from step 5 with the same dispersion agents as in step 2 and treat the deflocculated pulp by gravity. The minerals that tend to float with scheelite are generally of low specific gravity and the separation is efficient. The heavier contaminants, such as pyrrhotite and magnetite can be removed magnetically, leaving a practically pure scheelite. E. J. Pryor (Imperial College of Science and Technology, London)—It occurred to me that instead of using temperature as a differentiating control, more precision might be obtained with a reagent of a type we developed here for the flotation of high grade fluorspar in cold pulps. This reagent, which is manufactured on a modest scale in England, is based on oleic acid, which has been modified by our patented process to ensure complete stable dispersion at any desired concentration in water. It thus becomes possible to utilise unimolecular layers with good selectivity. In the fluorspar flotation for which we developed it, it is possible to hold a tight control on depressing quebracho for the calcite without substantial loss of flu-orite, and recovery exceeding 99 pct is not uncommon in the mill where it is in use, even under wintry conditions. No attempt has been made yet to extend the use of the reagent, as we have not completely overcome

Jan 1, 1952

By C. Y. Garber

INTEREST in the sink-float plant operated by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, has recently been largely confined to the preparation and reconditioning of the galena medium. The ease and simplicity of these operations in a concentrating mill producing a flotation lead concentrate has occasioned enough comment to possibly justify a brief description. The subject is treated from an operator's viewpoint only; no effort is made to discuss it in a theoretical or technical manner. PLANT AT BUNKER HILL The sink-float plant was first operated in December 1941. It was built for the purpose of quickly increasing mill capacity with a minimum of equipment. It is the Huntington-Heberlein sink and float process using galena medium and is operated under license from the Sink and Float Corporation, New York city. Lead-zinc ore from the Bunker Hill mine is crushed to pass a I ¼ in. screen and is then washed and separated on vibrating screens having 4 ½ -mm. round-hole punched plates. The screen undersize, amounting to 33 per cent of the mill feed, is dewatered and sent to the ball-mill feed bins. The screen oversize goes to the sink-float plant, where 50 per cent of the oversize, or 33 per cent of the mill feed, is float, which is washed free of medium and disposed of as a tailing. The remaining 33 per cent is sink, which, after washing, is crushed to pass ½ in. and joins the undersize in the ball-mill feed bins. The normal plant capacity is 1700 tons per 24 hr. About 1.7 per cent of the total lead and 3.3 per cent of the total zinc in the feed is lost with the sink-float tailings (Table I). [ ] More complete descriptions of the H. H. process and Bunker Hill sink-float plant are given in several recent articles, listed at the end of the paper. PREPARATION OF MEDIUM AT BUNKER HILL New medium is made intermittently as needed, usually 12 hr. in each 6 days. A small portion of the current mill flotation concentrate is diverted from the lead cleaner cells to a I-in. vertical sand pump and pumped to a two-cell 36-in. Agitair flotation machine, where NaCn and ZnSO4 are added and the grade of concentrate is improved as shown in Table 2. Tailing from this operation is returned by gravity

Jan 1, 1946

Discussion of the paper of PHILIP W. HENRY, presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January, 1915, pp. 23 to 30. C. ,E. GRUNSKY, JR., San Francisco, Cal. (communication to the Secret ary*).-The difference of opinion of engineers on the subject of depreciation is justified, to some, extent, by the many viewpoints from which such a subject can be considered when applied to properties of widely differing physical characteristics. Mr. Henry takes up the subject of depreciation as applied alone to oil properties, and in doing so makes a clear distinction between amortization and the repair or renewal requirement. After carefully reading the paper the purpose of its author in suggesting a "depreciation" reserve or fund to keep the property at a constant value does not seem clear. As shown by Mr. Henry, the depreciation element as compared with the operating expense per gallon of oil is very large because of the comparatively short life of the oil properties, and it is also evident that such a "depreciation" fund would in a short time contain a very large amount of money. It seems desirable and permissible in income-tax matters to take into account the depreciation of property and to separate from the income such money as is necessary to amortize the invested capital to an extent warranted by the depreciation. However, it does not seem either necessary or desirable to create a large fund which will in time approximate the entire invested capital and which may he invested by the directors, as Mr. Henry suggests, "in the property itself or in outside securities." This method seems cumberome and liable to offer in the reinvestment of such a fund temptations to a directorate that might show more devotion to its own interests than that of the stockholders. A reserve fund is very frequently desirable in mining and oil operations, but to keep up a fund of this magnitude or to reinvest it in outside securities does not seem desirable from a stockholders' standpoint. The. money withdrawn from the receipts to be placed in the depreciation fund (not including replacements and the drilling of new wells necessary to keep up the productiveness) should he returned to the stockholders of the company, not as dividends, but as an amortization of the invested capital.

Jan 5, 1915

The cables brought the news last spring that the Institute had lost by death one of its most distinguished foreign members, Hjalmar Sjogren of Stockholm. For thirty-one years, Professor Sjogren had been one of our number. He was elected in 1891, joining the Institute at the time he was in the United States, in attendance at the Fifth International Geological Congress, which was held in Washington in the late summer of that year. Professor Sjogren was once more in America in 1906 and again in 1913, and on both of those visits his friends in New York had the welcome opportunity of extending courtesies to him. He was thus well known to a wide circle in our membership. His keen interest in the geology of iron ores brought him in touch with the many Americans who have studied them and who have been active in the important productive districts which he visited. Our Transactions contain (Vol. XXXVIII) one very important paper of seventy pages on the Geological Relations of the Scandinavian Iron Ores, which he contributed. Sten Anders Hjalmar Sjogren, to give his full baptismal name, was born June 13, 1856, and was the son of Anton Sjogren, a mining engineer, at the time in charge of the iron mines at Persberg, in the east and west iron-ore belt of central Sweden, about 160 miles west from Stockholm. The Persberg orebodies yielded magnetite and specular hematite from schists, with which limestones. were interstratified as well as the peculiar Swedish rocks called "halleflinte." The mines were also well known to collectors and students of minerals. While Hjalmar Sjogren was yet a lad, his father was advanced to the superintendency of a number of famous mining localities in this same district of Wermland. Paisberg, famous for its native lead, was one; and two others, Langban and Nordmarken, were among the most prolific sources of interesting minerals in all Sweden. In several localities, the pre-Cambrian limestones had obviously experienced the recrystallizing influences of intrusive igneous rocks and had been charged with the so-called "contact" minerals, which have found their way to the museums of the world. Anton Sjogren, the father, was a keen mineralogist and Hjalmar, the son, grew up in a favorable environment for receiving training and enthusiasms of the same sort. One is not surprised, therefore, to find Hjalmar Sjogren, in the long run, turning to mineralogy and geology as his final career.

Jan 1, 1923

By Jos. J. Walsh

Ventilation within a coal mine is essential to the welfare of those employed therein, from the standpoint of health, safety, and efficiency. While the saving of life and the preserving of health are the chief reasons for ventilation, efficiency and production are increased. In spite of the fact that we speak of air as having a certain composition, the proportions of oxygen, nitrogen, and carbon dioxide are not fixed, but vary between small limits. The different elements are not chemically united, they are merely mixed and each is free and can be separated with little energy. For this reason air in the mine workings is seldom found in a pure state. Factors that necessitate ventilation in coal mines are those that change the composition of pure air. Contamination of mine air results from the burning of oil-fed flames, the use of explosives, the oxidation of coal, and the liberation of gases by the coal. The extent to which these factors exist governs the size and general plan of the ventilating applianccs required. An efficient ventilating system is one that will furnish air at the working faces in sufficient volume to dilute and render harmless noxious gases and at the same time maintain an oxygen content closely approaching that of pure air. In a well-ventilated mine, the oxygen seldom falls more than 0.5 per cent. below normal. The carbon-dioxide content of the air in the average coal mine will vary from 0.1 to about 0.8 per cent., which amounts are not harmful. Three per cent. of carbon dioxide in air doubles the frequency and the depth of breathing; it is plainly noticeable and if breathed continuously for several hours its effect would probably be harmful. Slight reductions in the oxygen content of the air, such as occur in well-ventilated mines, have no debilitating effect on the worker. A person not exerting himself would fail to observe any unusual physical effect in an atmosphere: containing 17 per cent. of oxygen. This condition, however, or even a condition showing an oxygen content below 20 per cent., would indicate poor ventilation and that the elements which tend to reduce the efficiency of the worker are present, namely water vapor and a high wet-bulb temperature.

Jan 1, 1923

By G. Thomas, O. Johari

MEIERAN and Richman' have proposed a method for the determination of electron-diffraction patterns from twinned bcc crystals. It is the purpose of this note to present a general method capable of predicting the positions of all reflections from both matrix and twin regions for all possible orientations of cubic crystals. The method has been verified for twinning in explosively deformed copper, and is found to be a very useful tool when used in conjunction with stereographic projection, and dark-field electron microscopy. Let an isometric crystal be twinned in any (hkl) plane. The twinning can be considered either as a reflection in the twin plane or as a 180-deg rotation about the twin axis. In reciprocal space, the 180-deg rotation about the twin axis would place a given point p, q, Y to a new position P, Q,R, such that both will be equally inclined to the twin axis. This is represented in Fig. 1. If the coordinates of three such pairs of points are determined, the matrix of the transformation can be obtained.' It is also seen that such pairs would satisfy another condition, i.e., the vector [p,q,r] plus the vector [P,Q,R] will yield a multiple of hkl, i.e., the indices of the twin plane, because in isometric systems the axis [hkl] is perpendicular to the plane (hkl). This can be simplified by taking the points along the three axes. If a point h2 + k2 + 12, 0, 0 is taken along the x axis, it is seen that its new indices should be so as to yield a sum 2h2, 2hk, 2hl,i.e., 2h(h,k,1). (Also the points h2 - k2 - 12, 2hk, 2h1, and h2 + k2 + 12, 0, 0 are equidistant from the origin and both points make equal angles with the twin axis, i.e., cos-' h/dh2 + k2 + l2.) Similar operations for the points yield respectively, after the 180-deg rotation about the twin axis. Following the method due to Buerger,' the matrix of the transformation is obtained as follows: Using this matrix the indices of any other point in reciprocal space can be determined. This matrix is much simplified for (111) twinning commonly encountered in fcc metals, since are each equal to —1; hence

Jan 1, 1964

By Edward Keller

ALTHOUGH the subject matter contained in this paper is presented under a new title, its writing was induced by the work of S. Skowronski and K. W. McComas.1 A discussion of the latter is here combined with the presentation of new and independent data. The physical constants quoted by the authors of that paper, such as melting and boiling points, as also the chemical reactions of the substances involved, are so well established that the numerous confirmatory experiments and their application to metallurgical conditions leave little or no room for criticisms. On the contrary, they will greatly aid to dispel any lingering skepticism as to possible considerable losses of copper accruing when the metal is melted in the presence of its own and, probably, other chlorides and when no provision is made for the recovery of volatile products. Exception may be taken, to some degree, to that part of the work under the caption Melting Drillings of Copper Mixed With Sodium Chloride. These experiments should have been extended in order to make the implied reactions clear and the results convincing. The latter are stated to be, "that when sodium chloride is present above certain minimum quantity relative to copper some of it is found to volatilize in the melt while another part reacts with the metallic copper to produce the volatile cuprous chloride, and that When smaller quantities of sodium chloride are present the reaction is complete and all chlorine is found to have volatilized as cuprous chloride." Metallic copper and sodium chloride are mentioned as the sole reagents in this chemical process, acting, according to the authors, in a neutral atmosphere of carbon dioxide. The chemist, quite naturally, will inquire into the formula according to which that reaction takes place and find that it would present itself as follows: 2Cu + 2NaC1 = 2Na + Cu2Cl2 It would appear that the truth of this formula will be challenged and a more rational explanation of the reaction sought. Apparently, carbon dioxide is neutral relative to metallic copper in its molten state; whether it remains neutral in the presence of sodium chloride is quite another question. Does it not at that high temperature become an oxidizer and do not the conditions of the reaction change to those expressed in the following formula? 2Cu + 2NaCl + 2002 = Na2CO3 + CO + Cu2Cl2

Jan 9, 1919

By R. L. Lloyd

UNLIKE the development of sintering lead, copper and zinc ores, the sintering of fine irony material had its birth, not as a result of gradual growth along lines aimed at the production of sintered and agglomerated product, but because the success of the sintering operation in other lines had been brought to the attention of the ironmasters, who were immediately attracted by the prospect of being able to convert their own fines-into a similar product. The abundance of iron ores in the United States and their comparative cheapness had led iron men into the habit of not paying particular attention to the fine material blown out of their blast furnaces. Hundreds of thousands of tons had been stacked up and used only during times of shortage of ore and then usually without any preliminary preparation, though many attempts had been made to briquette it. Briquettes proved good material, but the operation of briquetting was too expen-sive when applied to iron-ore fines. The development of the iron-ore blast furnace in the United States tended toward large units, high columns and heavy blast pressure, and this tendency is still peculiar to this country, whereas in the other countries the tendency has been to smaller units, lower columns and lower blasts. The high blast pressures and swift driving of the American blast furnace tend, of course, to produce more flue dust than European practice, and this production of flue dust was augmented when large quantities of soft ore, of which the Mesabi is typical, came on to the market. These ores are desirable chemically but physically they are soft, friable and fine, and when they are used in the iron blast furnace the flue dust produc-tion is increased. The necessity of rehandling the flue dust lead to briquetting on an extensive scale. The binders used were either chemical or mechanical, and in one system the briquettes were kiln fired in very high temperatures. Rotary kilns, coal or oil fired, were used extensively, and gave a product of hard and more or less nodulized material, but at considerable cost. This was the situation in regard to iron flue dust when the late James Gayley and his associates became interested in the idea of sintering the iron blast-furnace flue dusts under their own fuel (included coke dust) of which they carried between 15 and 30 per cent.

Jan 10, 1922

By Roscoe C. Clark

In a previous technical note' by Walter Rose, evidence is offered in support of the contention that "the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely." It is not the purpose of this note to present further discussion of this possibility but rather to point out that the argument presented there does not appear to be generally valid. In the cited note' reference is made to the experiments of Welge2 wherein it was shown that when water was displaced by oil from a core the pressure in the water phase was less than in the oil phase but that when this oil was then produced by water drive the pressure in the water phase was greater than in the oil phase. Rose has concluded from these observations that conditions of static equilibrium did not obtain since the fluid saturations were such that phase discontinuities seemed unlikely. The argument from which this conclusion was drawn is based on the contention that "the pressure is always greatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase." This premise appears to have been reached from a consideration of capillary phenomena in cylindrical tubes, although it may a1so hold for other types of pore geometry, hut as will be shown below it does not hold for all pore shapes and hence is not generally applicable. Since the pore structure of porous media such as reservoir rocks i- in general so complex as to defy exact description. it is undoubtedly of great value to establish a model in terms of pore shapes of known geometry, provided of course that the limitations of the model are recognized. That the limitations of the capillary. or cylindrical, tube model have not always been fully recognized will be evident from the following discussion of a pore of different shape hut one which may a. logically he considered a.; the capillary tube. The pore space to be considered is that shown in Fig. 1, which may be thought of as the "hole in a doughnut."* Consider the interface, A-B-A', between two immiscible fluids, P, and P2, which interface meets the solid alone a line, A-C.A'-C'. The interface A-B-A' is the surface of a spherical segmen† while the line of mutual contact be-

Jan 1, 1950

By W. L. Chu

It was observed that chromized coatings on low carbon steel could be embrittled by cooling slowly through the 475°C range. A higher chromium coating was more susceptible to embrittlement than a lower chromium coating. Coating structure and composition could be correlated with the chromizing process and prior carbon content of the steel. IT was recently observed that during the fabrication of rectangular tubings made with chromized thin gage 1010 steel, a high percentage of these parts were fractured readily in a brittle manner under the light impact-forming load employed. Ensuing investigation indicated the cause for such brittle failures to be the so-called 475°C embrittlement of the chromized coatings. The experimental work and results are briefly reported. Rectangular tube sections of normalized AISI C1010 steel, which had a cross-section of 0.5x1.5 in. and a wall thickness of 0.030 in., were chromized to yield coatings having several ranges of thickness, varying from 0.0005 to 0.002 in. Essentially, the chromizing process is similar to that described by Samuel and Lockington,' which consists of heating the parts in a sealed container at about 955°C for 4 hr in intimate contact with a chromizing mixture* samples in a hydraulic press, and the other employed a simple beam bending test of the flat sides of the tubing walls. Neither, however, was able to differentiate the relative brittleness of samples known to include both the brittle and tough types, since the impact-brittle samples were found to deform readily in a manner similar to the tough ones. Both the tough and brittle samples were studied by reflection microscopy. Observation showed that the microstructures of the steel cores were similar in content and distribution of inclusions as well as in the ferritic grain size. Results of Filar micrometer measurements showed that coating thicknesses+ of the brittle samples averaged 0.0007 in., whereas those of the tough samples averaged 0.0016 in. The micrographs of Fig. 2 illustrate the structural differences between coatings of both types of samples. By dissolving the steel cores in nitric acid, coatings of both the brittle and tough samples were isolated. Simple bending tests showed that coatings of the brittle samples cracked readily at about 90" bend, whereas those of the tough samples could be bent nearly 180° without cracking. The coatings as well as the steel cores were analyzed for carbon and

Jan 1, 1956