Search Documents

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. 1). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944

By T. E. Leonitis, F. N. Rhines

The oxide scale that forms upon magnesium at elevated temperatures is non-protective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth' and has been verified by Suzuki2 and by ScheiL3 Pilling and Bcdworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki," he product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavaults observed that excrescences form upon liquid magnesium and alloys in thc course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium' and calciums minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.~ Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Schcil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. Experimental Procedure and Results The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the 6c

Jan 1, 1946

By Charles H. Fulton

Experimental work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc-lead ores, since the residue from the distillation IS held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet may be used over again as coke, or as a high ash coke for fuel purposes in power production. Baked briquets are hard and tough and may be handled roughly

Jan 1, 1921

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. I). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944

By Francis Foley

Small cracks in a plane normal to the axis of steels are found to be prevalent around the water hole of drill steels that have been in service for an unknown period of time. Cracks are not found on the exterior surface of the steels nor to any noteworthy extent even in the water holes of new drill steels. Undulations and serrations are found in the surface of the water hole in new steels; it is in the bottom of such defects that cracks appear to develop in used steels. The occurrence of the more serious of these cracks at the point in the steel to which it has been heated for forging or hardening is thought to account to a great extent for failures in that region. DURING the past, year, we have investigated the cause of 88 per cent, of the failures by breakage near the bit end of some 1-in. hollow, hexagon, drill steel used in a metal mine. This breakage in the region of the bit end of the steel was peculiarly interesting because we have been led to believe that breakage is most prevalent at the shank end of drill steels near the place where the steel is gripped in the chuck of the machine. Records from the mine showed, also, that the breakage was much more frequent in the short lengths of large gage than in the longer steels; this is shown graphically in Fig. 1. Because the shorter lengths of steels are usually those that have been made from broken pieces of long steels or from steels that have worn down in service, rarely being made from new stock, those who are wont to suspect steel of tiring and crystallizing in its old age through fatigue are quite apt to see in this instance an argument in favor of their idea. As usual, a careful examination of these steels reveals defects of a character hardly to be overlooked in favor of such a cause. The steel in question was rolled with a sand core and was of the usual drill steel composition: Carbon 0.85 per cent., manganese 0.60 per cent., silicon 0.25 per cent., phosphorus 0.02 per cent., and sulfur 0.02 per cent., with the exception that in some specimens there was vanadium, not exceeding 0.20 per cent.

Jan 3, 1924

By Alfred H. Bell, Paul F. Simpson

The year 1929 was one of continued activity in the petroleum industry of Indiana and Illinois but the new production obtained has not been sufficient to offset the decline in the production of the old wells. (Table 1). Drilling costs have not changed materially during the year and the prices of crude oil have increased slightly so that the prospects for further testing are good. The total number of completions in Illinois in 1929 (Table 2) was greater than for any year since 1917. More than half of these were in the Dupo field, St. Clair County, and the development of this field was largely responsible for the increased ratio of producers to dry holes in the state as a whole. In the southeastern Illinois field which has produced about 97 per cent. of the state's petroleum the number of completions was greater than in 1928 and the percentage of producers was a little higher. Although a number of scattered wildcat tests were drilled most of them were not located on favorable structure and the only noteworthy discovery was that of a shale-gas horizon at shallow depth in Morgan County in western Illinois where gas has been produced for a number of years from sandstone and limestone. In Indiana the number of completions (Table 2) was only slightly less than in 1928. Most of the new wells were drilled in the southwestern part of the state, which now produces more than 90 per cent. of Indiana's petroleum.

Jan 1, 1930

Date of Congress: Sept. 20-25, 1915 The Committee on Local Affairs is fortunate in having secured for a period expiring on Oct. 17, an option. on 100 rooms at the Palace, St. Francis. and Fairmont hotels, the three leading hotels in San Francisco, with the distinct understanding that, on account of previous engagements whereby the hotels are reserved to their capacity, the rooms must be vacated on Sept. 25, 1915. The rates applying will be $7 per day for the court rooms occupied by two people, or $10 per clay for outside rooms occupied by two people. The outside rooms will face the main thoroughfares at the Palace and will face the city and bay at the Fairmont, which latter is situated oil a high hill. The St. Francis faces an open square and is flanked by main thoroughfares on two sides. If any members desire their reservation to extend either before the 20th or beyond the 25th, the Committee will use its best endeavors to secure such extension in individual cases, in accordance with the indicated wish. The Hotel Bureau in San Francisco is co-operating actively and closely with the. Committee on Local Affairs of the International Engineering Congress and offers the choicest rooms in any of 350 hotels other than the three mentioned above. This Hotel Bureau controls 50,000 rooms in San Francisco, which are all provided with hot and cold water, stationary basins, baths, house telephones, elevators, and bell boy service.

Jan 9, 1914

By E. V. Given

In speaking of the concentration of oxidized lead ores at St. Anthony, I do not wish to infer that we believe all lead ores of a similar grade can be mined and treated at a profit. Our oxidized ore is low grade, and certainly the mine under present economic conditions could not operate on this ore by itself. Because of favorable conditions we can operate the oxide circuit at a small profit although we do not allocate overhead, pumping, and certain other general charges to it. Operations in the oxidized zone were started as an essential part of the development necessary to outline and mine the sulphide ores. Nearly all of our oxidized lead ore comes from the Collins section of the mine, with the transition from oxide to sulphide ore lying between the 600 and 700-ft levels. Production from sulphide ore is much larger than from the oxide, both in tonnage handled and in grade of ore. The oxide and sulphide ores are never mixed either in the mine or the mill. The oxide mill sections have their own ore bins, grinding, and flotation departments. The lead minerals contained in the ore, in the order of their importance are cerussite, wulfenite, galena, anglesite, and vanadinite. The ratios of the different lead minerals change as the ore is pulled from different parts of the mine-total lead being approximately 50% to 60% cerussite, 20% wulfenite, 15% galena, zero to 10% anglesite, and 2% vanadinite. About 3% of the lead was unidentified.

Jan 5, 1950

By A. T. Schwennesen

Every engineer has occasion to trace or copy a map, plan, or other drawing on paper too thick for the ordinary way of using tracing-cloth or tracing-paper. When the figure is small and simple a copy may be made by holding the original against a window-pane, coverin& it with the paper, and tracing direct by the aid of the strong sunlight from outside. The need of utilizing this principle on a larger scale and in a more convenient position led Dr. J. C. Branner to plan the table of which the following is a description : This table was first made in the form of an adjustable glass-top table with a mirror beneath, in 1887, while Dr. Branner was State Geologist of Arkansas. Later it was modified as experience suggested until the form as here described was evolved. The device consists essentially of a drafting-table with a plate-glass top, upon which the original drawing and the paper are laid, and a mirror mounted underneath to reflect the light of the sky up through the drawing. The glass top is hinged and fitted with two arms and thumb-screws, so that it can be raised and fixed to any position, either inclined or horizontal. The mirror is pivoted and revolves about a horizontal axis, so that it may be tilted to any angle. The hood of cardboard or black cloth prevents the reflection of light from the tracing, and may or may not be attached to the table.

Jan 1, 1912

By Oscar Lachmund

DURING the driving of the main haulage level at the Copper Mountain mines of the Canada Copper Corpn., Ltd., near Princeton, B. C., some very rapid driving was clone, though no claim for a world's record is made. Conditions, however, were unfavorable for economical operations. The cost of power was high, for the fuel was of poor grade; besides, during the time the work was in progress, very little other power was needed so that most of the power cost was charged against the footage. The FIG. 1.-DRIFT ROUND USED IN MAIN HAULAGE LEVEL, COPPER MOUNTAIN, B. C. transmission line consisted of No. 4 galvanized iron wire with the result that the line loss was considerable. The voltage transmitted was about 30,000. The plant was operated under a lease, which was due to expire about the same time this work was supposed to be completed; an extension was refused, therefore speed was most important. The plans called for a straight adit 2900 ft. (884 m.) in length. At a point 2800 ft. (853 m.) from the portal, two raises were to be put up to the next nearest workings, a difference in elevation of about 800 ft. (243 m.). One of these was to be a two-compartment hoistway and the other a zigzag ore pass, or muck run. A location for these raises had been determined by a number of diamond-drill holes, but the material to be penetrated by the alit was not known. It seemed imperative to get the tunnel work completed as rapidly as possible, in

Jan 3, 1919

GENERAL GEOLOGIC DESCRIPTION The Escalante silver deposit located in southwestern Utah is an epithermal vein system consisting of a hanging wall and footwall vein, straight along strike and dipping about 1.2 rad (70°). The veins consist of banded quartz and calcite fissure fillings between volcanic wall rock that are silicified for some distance outward from the vein. The walls of the veins are sharp and the silver values are irratically distributed through the various bands within the vein. Only very low grade values are to be found in the wall rock on either side. The portion of the veins above the water table have been somewhat leached, with some secondary enrichment below. The mineralogical zonation is variable due to a fluctuating water table through geologic time. SAMPLE MANAGEMENT AND COMPOSITE ASSAYS Sample data for the deposit was obtained from over 50 diamond drill holes, from channel samples cut at intervals across a drift, and from scattered surface trenches along the out- crop of the hanging wall vein. Fig. 13-1 is a surface plan map showing the vein outcrop and some diamond drill locations. Two cross sections through the vein are shown in Figs. 1 3-2 and 13-3. Nearly all of the diamond drill core of vein material was assayed in 0.3-m (I-ft) lengths, from which weighted composite assays were manually calculated for the horizontal thickness of the vein. The centers of the composited samples were plotted in north and east coordinates and by elevation, and locations and assay

Jan 1, 1980

By John V. Beall

Probably the only hotel in the world with near 100% occupancy at all times is the modern Hotel Indonesia in Djakarta. However, there is little gaiety among the scores of business men who occupy the hotel because they fret as days grow into weeks in seemingly interminable negotiations with government officials. As one man put it, "time is a dimension that they [Indonesians] have never grasped." But the visitors still come in droves to investigate business opportunities in this sprawling nation of tropical islands which is, with 120 million people, the fifth largest nation in the world. Approximately $300 million is being spent each year in Indonesia by foreign companies and governments. Aid grants from the latter are derived about one third from the United States, one third from Japan and the remainder from many nations. Djakarta is a far cry from pleasant colonial Batavia, as the city was called under the Dutch. The orderly colony of prewar days was managed as an agricultural and trading dependency of Holland. The Dutch did little about educating the people. The islands were controlled by the Japanese during World War II and afterwards there was a war for independence--which was attained in 1949. In the ensuing years, President Sukarno devastated the economy by squandering money on a gigantic scale. A Communist-attempted coup in 1965 resulted in a military takeover and the extermination of Communists. The new government under Suharto, which took over all power in March 1966, found itself in a situation where bare survival was the first consideration.

Jan 1, 1970

By E. S. Bardwell

DURING the period extending from May, 1922, to September, 1923, the copper-refining furnaces of the Great Falls Reduction Department of the Anaconda Copper Mining Co. at Great Falls, Mont., were operated exclusively with pulverized coal as fuel. The installation was made first as an experiment. It proved successful from the start and was abandoned solely because fuel oil from the Sunburst field became available at a price sufficiently low to make its use desirable from an economic standpoint. The equipment required for pulverized coal has, however, been kept intact and is available for immediate use should the oil supply fail. Inasmuch as pulverized coal had been used on two large reverberatory smelting furnaces and was, at the time we were considering its application to the copper-refining furnaces, being used on the Wedge furnaces roasting zinc concentrate for the electrolytic zinc plant, we were equipped with a coal-pulverizing plant of ample capacity to supply pulverized coal for the furnace refinery. The only problem was to devise suitable means for transporting pulverized coal from the pulverizer plant, located in the smelter building, to the refinery about 1000 ft. distant and about 150 ft. above the level of the pulverizer plant. When studying this installation, it should be borne in mind that the layout represents an adaptation suited to the existing conditions at this particular plant. The installation was entirely satisfactory and uniformly dependable but might be modified to advantage from an operating point of view if an entirely new installation were being planned.

Jan 9, 1925

By Oscar Lachmund

During the driving of the main haulage level at the Copper Mountain mines of the Canada Copper Corpn., Ltd., near Princeton, B. C., some very rapid driving was done, though no claim for a world's record is made. Conditions, however, were unfavorable for economical operations. The cost of power was high, for the fuel was of poor grade; besides, during the time the work was in progress, very little other power was needed so that most of the power cost was charged against the footage. The transmission line consisted of No. 4 galvanized iron wire with the result that the line lass was considerable. The voltage transmitted was about 30,000. The plant was operated under a lease, which was due to expire about the same time this work was supposed to be completed; an extension was refused, therefore speed was most important. The plans called for a straight adit 2900 ft. (884 m.) in length. At a point 2800 ft. (853 m.) from the portal, two raises were to be put up to the next nearest workings, a difference in elevation of about 800 ft. (243 m.). One of these was to be a two-compartment hoistway and the other a zigzag ore pass, or muck run. A location for these raises had been determined by a number of diamond-drill holes, but the material to be penetrated by the adit was not known. It seemed imperative to get the tunnel work completed as rapidly as possible, in

Jan 1, 1920

By Victor Rakowsky

A CLEAR understanding of the factors that deter-mine the consumption of zinc metal is essential to a proper survey of the future of the industry and the relation of the several producing districts. With a view of explaining a sound basis for the consider-ation of some of the problems facing the zinc-mining industry of the Oklahoma-Kansas and Missouri district some of these factors are here set out. The zinc industry of the United States furnishes metal for three major uses, viz.: (1) zinking iron and steel (galvanizing); (2) brass making; (3) sheet rolling. Other important uses are for lead desilverization, the manufacture of castings, including die castings, and the manufacture of zinc oxide by the French process, which consists in burning spelter. The use of zinc for galvanizing comprises the coating of sheets, tubes, wire and shaped products, the latter ranging from chains to buckets. The brass-making industry may be sub-divided into manufacture of red brass, yellow brass and white brass, the percentage of zinc in these products being roughly 30, 40 and 80 respectively. The use of white brass is relatively a new thing and it may attain considerable proportions as a substitute for yellow brass. Ingalls estimated the percentage of total metal consumed for the above purposes in pre-war times as follows: HIGH PRODUCTION RECORD, SHORT TONS USES PERCENTAGE OF METAL Galvanizing 60-65 210,000 in 1912 Brass making 17-20 175,000 in 1916 Rolled sheets 10-12 57,000 in 1917 Other uses 5- 7

Jan 3, 1923

By S.G. Bankoff

Ince1 proposed that electrostatic attraction between oppositely charged particles was responsible for slime-coating. Del Giudice2 postulated the metathetic formation of a cementing compound. Wark3 suggested that prevention of slime-coating was related to peptization of the slime. In the experiments of Table I the technique employed was essentially that of del Giudice, with the difference that the particle was examined under a film of water rather than dry.4 In general, the polished particle was agitated for 2 min. in a pulp consisting of 12.5 grams of the slime (—200 mesh) and 50 C.C. of distilled water, washed in three baths of distilled water, and examined at 220 diameters with the Leitz Ultropak. Observations of Brownian movement were made at 850 diameters with dark-field illumination. Several of these experiments do not jibe with the metathesis theory. According to published solubilities,5,6 the lead salts of the anions in experiments c through g are more insoluble than lead carbonate, there- fore should prevent the formation of lead carbonate on the galena surface. In experiment i the calcium oxalate, which precumably was on the calcite surfaces, should have permitted the formation of a lead carbonate cement by virtue of its greater solubility. Experiments j through m show that the addition of lime accelerates the deposition of quartz onto a galena surface. The writer is unable to postulate a satisfactory cementing compound, according to the metathesis theory, to explain this effect. These experiments led to the conclusion that the metathetic formation of a cement-

Jan 1, 1943

By S. G. Bankoff

INCE1 proposed that electrostatic attraction between oppositely charged particles was responsible for slime-coating. Del Giudice2 postulated the metathetic formation of a cementing compound. Wark3 suggested that prevention of slime-coating was related to peptization of the slime. [ ] In the experiments of Table I the technique employed was essentially that of del Giudice, with the difference that the particle was examined under a film of water rather than dry.4 In general, the polished particle was agitated for 2 min. in a pulp consisting of 12.5 grams of the slime (-200 mesh) and 50 c.c. of distilled water, washed in three baths of distilled water, and examined at 220 diameters with the Leitz Ultropak. Observations of Brownian movement were made at 850 diameters with dark-field illumination. Several of these experiments do not jibe with the metathesis theory. According to published solubilities,5,6 the lead salts of the anions in experiments [c] through g are more insoluble than lead carbonate, therefore should prevent the formation of lead carbonate on the galena surface. In experiment [i] the calcium oxalate, which presumably was on the calcite surfaces, should have permitted the formation of a lead carbonate cement by virtue of its greater solubility. Experiments [j] through m show that the addition of lime accelerates the deposition of quartz onto a galena surface. The writer is unable to postulate a satisfactory cementing compound, according to the metathesis theory, to explain this effect. These experiments led to the conclusion that the metathetic formation of a cement-

Jan 1, 1941

By Olof Löfgren

PART 1 INTRODUCTION All modern pelletizing plants are equipped with either the drum or the disc circuits. Choice of one or the other circuit is not simple and it is desirable to establish a firm basis for such a task. For a meaningful and a fair comparison it is necessary to have the two systems working in parallel in the same plant with the same concentrate under the same supervision. Furthermore, the comparison has to be based on a defined green ball quality and size distribution. BALLING CIRCUITS The LKAB straight grate plant at Malmberget, Sweden, was started up in Septenber 1973. It was designed for a 2.5 Mton annual capacity and was equipped with five balling drum circuits. During the first year of operation it was found that the induration plant had the potential for a higher capacity which required increased balling capacity. For this purpose it was decided to install a balling disc circuit complete with a roll screen. The reasons for selecting a disc were space limitations and LKAB's desire to gather experience on balling disc circuits. The disc circuit was started up in 1975 and was run in parallel with the balling drums in the same plant and with the same raw material and under the same operating personnel. The necessary conditions for a comparison were thereby fulfilled. The data for the size distribution and quality of the green balls were obtained on random sampling during one year of operation, so that all the variations which appear in a commercial plant are covered.

Jan 1, 1977

By H. U. Schutt, J. M. Toguri

REGARDLESS of the degree of purification effected during the electrorefining of copper, a danger of re-introducing impurities exists in the operation of melting and casting of the refined copper. Logically only a combination of the purification and casting operation would remedy the situation. A well-known method of metal purification is the "Gross"-type process, whereby a volatile halide is produced, purified, and decomposed.' In the present case, this concept was used to remove the impurities rather than to form possible volatile copper halides. The object was to produce volatile halides of the impurities present and distill these away, leaving high-purity copper. It is interesting to note that such techniques are used in spectrographic procedures in order to shorten exposure time and enhance the density of impurity lines.' In the present investigation, copper hydroxy fluoride was used, since the temperature of decomposition of copper hydroxy fluoride and the melting point of copper nearly coincide. The fluorine released by the thermal decomposition of copper hydroxy fluoride purges the molten copper. Copper hydroxy fluoride was prepared by dissolving high-purity copper in nitric acid and adding hydrofluoric acid and ammonium hydroxide in the required proportions. The melt was made in a high-purity graphite crucible heated by an induction furnace. Trial experiments showed that impurities can be introduced from the crucible material. Therefore, preceding each cast, the crucible itself was cleaned by decomposing copper hydroxy fluoride and discarding the residual copper. Best experimental conditions were obtained by adding 30 g of copper hydroxy fluoride to 500 g of nor-

Jan 1, 1967

By S Bankoff

INCE1 proposed that electrostatic attraction between oppositely charged particles was responsible for slime-coating. Del Giudice2 postulated the metathetic formation of a cementing compound. Wark3 suggested that prevention of slime-coating was related to peptization of the slime. [ ] In the experiments of Table I the technique employed was essentially that of del Giudice, with the difference that the particle was examined under a film of water rather than dry.4 In general, the polished particle was agitated for 2 min. in a pulp consisting of 12.5 grams of the slime (-200 mesh) and 50 c.c. of distilled water, washed in three baths of distilled water, and examined at 220 diameters with the Leitz Ultropak. Observations of Brownian movement were made at 850 diameters with dark-field illumination. Several of these experiments do not jibe with the metathesis theory. According to published solubilities,5,6 the lead salts of the anions in experiments c through g are more insoluble than lead carbonate, there- [ ] fore should prevent the formation of lead carbonate on the galena surface. In experiment i the calcium oxalate, which presumably was on the calcite surfaces, should have permitted the formation of a lead carbonate cement by virtue of its greater solubility. Experiments j through m show that the addition of lime accelerates the deposition of quartz onto a galena surface. The writer is unable to postulate a satisfactory cementing compound, according to the metathesis theory, to explain this effect. These experiments led to the conclusion that the metathetic formation of a cement-

Jan 1, 1941