Search Documents

By K. P. Gupta

The Cb-rich boundary of the (Cb,Al) a phase field at 1250OC is near 41 pct Al. The Al atoms tend to occupy the C. N. 12 sites in this structure. A homologous (Ta,Al)a phase was identified. No a phase was found in the Mo-Al system at 1200°C. The first binary o-phase with a non-transition element as a major component was found1,2 in the Cb-Al system. The composition of this phase was reported2 as approximately 34 at. pct Al, based on X-ray diffraction patterns taken of alloys in the as-cast condition. Further study of the composition of this o-phase, therefore, appeared desirable. Since Si was previously found3,4 to occupy preferentially the lowest C.N. sites (I and IV) in the a phase, and preliminary resultsa indicated that Al may show similar ordering, one of the aims of the present work was to obtain more complete information on ordering in (Cb, Al) o. Among the binary systems of Al with Ti-, V-, and Cr-group elements, the Ti-Al, Zr-Al, V-Al, and Cr-Al systems are known to comprise no o-phase. In the present work a Ta-Al and a Mo-Al alloy were studied in an effort to find additional o phases with Al as a major component. EXPERIMENTAL PROCEDURES AND RESULTS An alloy with the intended composition of Ta + 40 at. pct Al was prepared by arc melting in He atmosphere. In both the as-cast condition and after annealing for 10 days at 1250°C and quenching in cold water this alloy consisted of two phases, as seen in the X-ray pattern and the microstructure. One of these phases was identified as the o-phase; the observed and calculated d-spacings are shown in Table I. The lattice parameters of this o-phase are a = 9.972 A, c = 5.214 A and c/a =0.5228, as determined from a Debye-Scherrer pattern using Fe K a radiation. The d-spacings for the unknown second phase are given in Table 11. The alloy contained approximately 25 pct of the unknown phase after annealing, as estimated on the basis of microscopic examination. A Mo-Al alloy was prepared by arc melting, with an intended Al-content of 35 at. pct. The alloy button was annealed for 7 days at 1200°C and water quenched. The X-ray pattern of the alloy in both the as-cast and the annealed state showed the reflections of Mo3Al (Cr30 type structure) and an unknown phase different from a. Six Cb-Al alloys were prepared in the composition range 30 to 50 pct Al. All alloys were arc melted in He atmosphere. After annealing for three days at 1175oC in evacuated silica capsules and quenching in water, the alloys with 30 to 40 pct Al contained three phases, namely the o-phase, Cb3Al (Cr3O-type structure) and an unknown phase. The alloys with more than 40 pct Al contained two phases, namely, what appeared metallographically, the o-phase and the same unknown phase. In the alloys containing less that 38 pct Al, the unknown phase was not present after annealing for 4 days at 1250°c,

Jan 1, 1962

By F. C. Schora, H. P. Meissner

Both a graphical and an analytical technique are presented for calculating stream compositions and temperatures in adiabatic staged systems in which solids travel countercurrently to a gas stream. Such a system might be a tower containing several plates, on each of which the descending solid is fluidized by the rising gas stream. Examples are presented in which chemical reactions occur, including the oxidation of SO, by a solid catalyst and the gaseous reduction of iron oxides. COUNTERCURRENT staged processes involving reactions between solid and gas streams are becoming more common. These operations are generally carried out in a series of beds of fluidized solids, with each bed or "plate" acting as a stage. Fig. 1 is a schematic diagram of such a series of stages located in a column, down through which a solids stream moves from stage to stage counter to a rising gas stream. Typical reactions carried out in such systems are the dehydration of aluminum trihydrate, the calcining of limestone, and the gaseous reduction of iron oxides. Calculation of the performance of these counter-current systems rapidly becomes more complex with increases in the number of stages and in the number of chemical reactions occurring. Calcula-tional procedures for isothermal operations of such systems have been described.4 Actual tower operations, however, are generally adiabatic, and in consequence far from isothermal. The object here is to present both graphical and analytical techniques applicable to such adiabatic towers operating continuously and in steady state. In this introductory discussion, the graphical techniques presented are of the McCabe-Thiele type, rather than of the Pon-chon type. In all the examples presented, it will be assumed that both thermal and chemical equilibrium are attained in each bed. The assumption that the gas and solid streams leaving each bed are at the same temperature as the bed is in accordance with the familiar behavior of actual fluidized solid systems. Chemical equilibrium, on the other hand, is not necessarily attained in any given stage between these two streams, even with deep beds, since reaction rates may be slow. In the last section of this paper, discussion is presented of methods suitable for use when chemical equilibrium is not attained. The adiabatic tower in Fig. 1 has "n" stages numbered from 1 to n, starting with the bottom stage as number 1. In analyzing this tower's performance, it is important to express gas flow rates in terms of a key component or element which remains completely within the gas stream throughout the tower. Similarly, solid flow is best expressed in terms of a key compound or element which remains within the solid phase throughout the tower. Thus, in burning limestone with a hot flue gas, the gas flow might be expressed as G, the pound mols of nitrogen flowing through the tower per unit time, while solid flow might be expressed as S, the pound atoms of calcium in all forms in the solid stream per unit of time. Defined in this way, both G and S are constant throughout the tower. The enthalpy of the gas and solid streams are now best expressed in terms of these key components. That is, the gas stream enthalpy H is expressed as Btu in the total gas per mol of the key component in the gas. Similarly, the solids stream enthalpy h is expressed as Btu in the total solid stream per pound mol (or pound atom) of the key component in this stream.

Jan 1, 1962

By E. R. Morgan

A series of manganese-rich ferromagnetic alloys has been studied. The alloys are based upon an interstitial solution of carbon in manganese. In each of the systems investigated, the ferromagnetic phase was found to be face-centered-cubic in structure. This magnetic phase is based upon the composition (Mn, X)4C; where X is a metallic element which has both a positive size factor with respect to manganese and a high positive valence. Typical elements of this type are aluminum, indium, and tin. Preliminary magnetic measurements indicate that the effective magnetic moment of manganese in the alloys is at least 1.0 Bohr magneton per atom. It is emphasized that the critical atomic separation beyond which ferromagnetism can occur will be governed by the electronic configuration of the manganese atoms. Lattice parameter measurements show that the ferromagnetic condition in the present alloys is associated with an increased atomic separation of only 3 to 6 pct compared with a hypothetical face-centered-cubic lattice of pure manganese. MANGANESE which is paramagnetic and not ferromagnetic in the pure state can become ferromagnetic if suitably alloyed. Under favorable conditions manganese can have an effective ferromagnetic moment of the order of 3.41,2 or even 4.0 compared with a moment of 2.2 Bohr magnetons for iron. The incidence of ferromagnetism is believed to be controlled by the degree of atomic separation.4,5 This is consistent with the fact that the atomic separation, when considered in terms of the ratio of the atomic diameter R to the diameter r of the 3d-shell, is larger in the ferromagnetic metals. The values of R/r calculated by Slater,' for metals of the iron group are given in Table I, and Slater has suggested that the critical ratio of R/r is 1.5. Consideration of the criterion of atomic separation alone would suggest that there are three classes of possible ferromagnetic manganese alloys: 1— Ordered structures, of either solution or compound types, such that manganese atoms are not near neighbors; 2—Structures in which the separation of near-neighbor manganese atoms is sufficiently increased by the presence of suitable solute atoms; and 3—Dilute solutions of manganese. Typical ferro- magnetic alloys of types 1 and 2 are the Heusler alloys and Mn4N, respectively. There are no recognized ferromagnetic alloys of type 3. In view of the proximity of the ratio R/r for manganese to the critical ratio of 1.5, the present work was concentrated on manganese-rich alloys rather than on ferromagnetic alloys of low manganese content, several examples of which are already known. Calculation of the distance of closest approach of manganese atoms in each of its allotropic forms, Table 11, indicates that the high temperature ? phase provides the most suitable basis for ferromagnetic alloys of high manganese content. However the high temperature forms of pure manganese cannot be retained on quenching, although a face-centered-tetragonal form apparently can be produced by electrodeposition. Since the critical separation which must be exceeded in order to obtain ferromagnetism is dependent upon the number of electrons in the d-shell, no exact critical value of R/r can be assumed. Not only will this separation vary from one pure metal to another, but it will also vary with the valency of the given type of atom when it is in an alloy. Raynor8 has shown that metals of the iron group probably

Jan 1, 1955

By W. L. Prehn, Adele Chambers, R. L. Slobod

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By H. H. Rachford

This work presents a first-order analysis of the instability underlying viscous fingering in adverse viscosity-ratio water floods. It extends previous analyses of frontal instabilities, which were carried out with equations for parallel plate models, by including effects of the saturation transition zone observed behind the front in water floods in water wet systems. This zone tends to insulate incipient fingers from the high-mobility watet;. thus conditions for the onset of fingering differ from those in the parallel plate theory. Finite-difference solutions of the two-dimensional equations of displacement in porous media exhibited the predicted stability characteristics in six hypothetical field- and laboratory-scale floods in rectangular reservoirs. In contrast to results with parallel plate systems, this paper concludes that for waterwet reservoirs, laboratory models scaled by the usual criteria are also correctly scaled for frontal instability. Further, fingering in the systems studied can occur in any saturation range behind the front, and may occur at an intermediate saturation even though stability obtains both at the saturation corresponding to the Buckley-Leverett front and near residual oil saturation. Other points of contrast are that the likelihood of occurrence of fingering may not increase as flow rate or viscosity difference increases, but my be sensitive to changes in he relative permealdlity and capillary pressure functions. INTRODUCTION The recovery of oil by water flooding frequently involves displacing the oil by water of a lower viscosity. Displacement of a fluid by a less viscous one may lead to gross channeling or fingering like that observed in solvent floods, in which it severely lowers recovery efficiency.1 In addition to adverse effects on recovery, it has been suggested that the unstable move- ment causing fingering may interfere with interpretation of scaled model studies of proposed water floods, since the instability in the model might not be faithfully scaled to that in the reservoir prototype. In view of the serious implications of this possible breakdown of widely used scaled model techniques4-6 it is the purpose of this paper to examine the question further. Instabilities in the solutions of systems of differential equations imply a loss of smooth dependence on initial and boundary conditions. Thus, the possibility exists that in using models whose scaling is based on the differential system there may arise size- and rate-dependent factors which are not properly scaled. This possibility was examined in detail by Chouke et al., who analyzed the instability of frontal advance in a related problem, water-oil displacement in parallel plate models,2 in which a moving interface separates two regions of constant, unequal mobilities. First-order perturbation theory predicts the existence of a critical wave length for the growth of perturbations: and a wave length of maximum instability of A, = The interpretation is that wave lengths in a perturbation which are longer than A, will grow. Thus, if the width of a two-dimensional channel is greater than A,, fingers will grow, and the spacing of the fingers which grow at the maximum rate will be approximately It is important that the higher the velocity and/or the difference in flow resistance, the lower is A,, and thus the greater the number of fingers that can grow in a given model. In applying these conclusions to porous media, a pseudo-interfacial tension, , was assumed for the invasion front. Since this would not necessarily be equal to the liquid-liquid interfacial tension, an unknown constant was substituted for the foregoing expression for A, This was determined

Jan 1, 1965

By R. L. Slobod, W. L. Prehn, Adele Chambers

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By D. J. Carney, E. Van Meter, J. J. Oravec

A study was made of combustion-air temperatures and factors affecting air temperatures in the open-hearth regenerative systems. Air-temperature surveys in the regenerative system revealed marked thermal gradients in the air above the checkers. The design of the fantail-uptake region plays a prominent part in increasing the heat recovery of the regenerative system. THE efficiency of the open-hearth regenerative system is one of the most important factors affecting open-hearth performance. Until recently, this factor has not received the attention in the literature given to many other items affecting performance, such as the type of charge, speed of charging, and the mechanical equipment of the open hearth. J. S. Marsh' emphasized the importance of the flame temperature and its dependence upon the combustion-air temperature. By means of measured air temperatures in open-hearth furnaces, data were presented which showed a remarkable degree of correlation between production rate and combustion-air temperature. This correlation was extremely good in view of the numerous factors, other than air temperature, which affect open-hearth production rates. In Marsh's work, a 100°F increase in air temperature reduced the heat time by approximately 45 min. Realizing the importance of combustion-air temperature, it is desirable to know which factors control the regenerative efficiency of the open-hearth furnace. B. M. Larsen recently discussed this subject.' The present paper illustrates a few of the more important items that affect regenerative efficiency and combustion-air temperature. In the latter part of 1951, a study of open-hearth combustion-air temperatures was begun at the South Works of the United States Steel Corp. In the initial work at open-hearth shop X, which produces low carbon steel products, temperatures were measured in the uptake in a manner similar to that used by Marsh' and the results obtained were very similar to the Bethlehem data. When it was decided to expand the study of combustion-air temperatures, open-hearth shop Y was selected because of the greater variety of furnace-design features, types of steel produced, and firing rates used. With the use of aspirating thermocouples, continuous gas analyzers, thermocouple and optical pyrometers, a study was made of: 1—effect of combustion-air temperature on open-hearth production rate, 2—thermal gradients present in various zones of the regenerative system, 3—effect of furnace-design variations on air temperature and heat recovery, 4-—effect of furnace-operating variables on heat recovery, and 5—variation in heat recovery with furnace age during the normal furnace campaign. Data collected on individual heats at 15 min intervals included air-flow rate, firing rate, checker temperature, combustion-air temperature, and furnace pressure. These data were collected on approximately 230 heats of steel. In addition, information was obtained at random on air infiltration and combustion-gas compositions. The data gathered have shown the desirability of closer control of open-hearth firing practices, a need for reducing air infiltration in the uptake zones, and a need for further study of design of checkers and of uptake-fantail areas. Equipment Air is practically a nonradiating medium. Consequently, in the measurement of air temperatures, the principle of heat conduction must be used rather than heat radiation. For this reason, aspirating-type thermocouple pyrometers normally are used to measure air temperatures. With these devices, air

Jan 1, 1956

By E. L. Kamen, H. D. Kessler, M. Hansen, D. J. McPherson

The highly reactive Ti-Mo and Ti-Cb alloys were prepared and heat treated under protective conditions. Phase diagrams were established based on micrographic and X-ray diffraction analysis and detection of incipient melting. ß titanium forms a continuous series of solid solutions with both molybdenum and columbium, whereas these metals are only slightly soluble in the a titanium modification. PREVIOUS work on the Ti-Mo and Ti-Cb systems was very limited and is discussed in succeeding sections of this paper relating to the respective phase diagrams. The diagrams in the present work were determined principally by micrographic analysis, because other methods such as thermal analysis and dilatometry are not suitable, due to the low diffusion rates of these alloys in the transformation range. X-ray analysis was believed less useful than micrographic analysis because: 1—On quenching certain high titanium alloys from above their transformation range, the body-centered cubic ß phase decomposes into acicular a (hexagonal close-packed) which room temperature X-ray diffraction techniques cannot differentiate from isothermal a. 2— High temperature X-ray techniques might be used, but are difficult to apply and are subject to error because of the high reactivity of titanium with gases such as oxygen and nitrogen. Although metallo-graphic study was the basic method used, X-ray diffraction analysis was applied to a limited extent, to further substantiate the findings. The transformation ranges on the titanium side of the Ti-Cb and Ti-Mo systems were studied both with DuPont Process A (magnesium-reduced) titanium alloys and with iodide titanium alloys. The Process A metal was used chiefly to bracket the transformation range in order to reduce the number of alloys given a particular treatment for the more accurate final study with iodide titanium alloys. Experimental Procedure The analyses of the metals used in the preparation of alloys for this study are presented in Table I. Melting Practice: Early in the work, a consumable electrode, arc melting furnace was used in the preparation of the Process A Ti-base Mo and Cb alloys. This type of furnace has been described by other investigators.', ' One of the major difficulties of the consumable electrode melting process was the prep- aration of homogeneous electrodes (with the mixture of coarse titanium sponge and fine powder alloying addition) which would give homogeneous ingots. Composition gradients encountered may have been due to a tendency for powdered alloying metals to drop away from the electrode in handling. This difficulty in the preparation of homogeneous alloys was overcome by the use of a nonconsumable electrode furnace for later work. This furnace is similar to the one used by Mc-Pherson and Fontana a Ohio State University. A diagram of the nonconsumable electrode arc furnace is given elsewhere.' The source of power was a 400 amp dc welding generator. Electrode tips of tungsten (% in. in diam) were used for all columbium melts and for a limited number of molybdenum melts. Molybdenum tips were used for the majority of molybdenum alloy melts. Columbium tipped electrodes were tried, but disintegrated rapidly at currents above 300 amp. In the Process A titanium melting practice the metals were charged into the water-cooled spun copper crucible in the following forms: l—titanium: sponge (—4 + 16 mesh); 2—molybdenum: sections of 0.003 in. sheet (approximately ½ in. sq); and 3— columbium: powder compacts (? in. lumps broken from large section). After alternately evacuating and purging the furnace several times with argon or helium, the arc was struck against the metal charge,

Jan 1, 1952

By R. D. Mollison, C. F. Fogarty

Sulfur is widely distributed in nature. It is present in the earth's crust, the ocean, the meteorites that come to us from cosmic space and in practically all animal and plant life. According to Clarke,9 the earth's crust contains 0.06 pct sulfur. Large quantities of free or combined sulfur are found in coal, natural gas and petroleum. Mineral waters contain sulfates and hydrogen sulfide. Sulfur is rather plentiful in the crust of the earth; however, only under special circumstances can it be produced profitably. Sulfur is one of the cheapest raw materials used by industry; and, therefore, the economic feasibility of a given deposit is strongly dictated by the law of supply and demand on local as well as world-wide levels. The forms which are commercially important are elemental sulfur or brimstone, and the sulfides such as pyrite (FeS2), pyrrhotite (FenSn+1), chalcocite (Cu2S), sphalerite (ZnS), and galena (PbS); the sulfates such as gypsum (CaSO4,2H2O), anhydrite (CaSO4), and kieserite (MgSO4,H2O). Elemental Sulfur Elemental sulfur is found in many localities, generally in solfataras and gypsum type deposits. The solfatara deposits are found commonly in the neighborhood of active or extinct volcanoes as in Italy, Japan and Chile, or fumaroles associated with mineral springs such as the Mammoth Hot Springs in Yellowstone Park. Here the sulfur is deposited in tufas or other porous host rocks. This type of sulfur deposit probably results from the oxidation of hydrogen sulfide or the reaction of hydrogen sulfide with sulfur dioxide. Most of the world's supply of elemental sulfur comes from the gypsum-type deposits. Here the mineral occurs as either crystalline or amorphous sulfur in sedimentary rocks in close association with gypsum and limestone. This association is characteristic and occurs in almost all the great gypsum beds of the world, although sulfur is not always present in quantities of economic importance. Various theories have been advanced to account for this association. Bischof5 suggested that the sulfur came from hydrogen sulfide which resulted from the reduction of calcium sulfate by carbon or methane in accordance with the following reactions: CaSO4 + 2C= CaS + 2CO2 CaS + C02+ H2O = CaCO3 + H2S CaSO4 + CH4= CaS + C02+ 2H20 2H2S + 02= 2H20 + 2S All of the sulfur-bearing domes on the Gulf Coast have calcium sulfate in great quantity in the cap. They all show the presence of hydrocarbons. The oxygen for the final reaction could have been supplied by circulating ground waters. The principal objection to this theory is that temperatures of 700° to 1000°C are needed to reduce the sulfate to sulfide with carbon compounds. The geologic evidence is that the temperature of the sulfur-bearing domes of Texas did not exceed 100°C. Proponents of the theory say that geologic time or a catalyst replaced temperature. According to another theory the sulfur in the salt domes is the result of bacterial action. Sulfate reducing bacteria have been detected in sulfur cores and in the formation water issuing from salt domes. It has, therefore, been suggested that these bacteria converted the sulfate to sulfide which subsequently was converted to elemental sulfur.

Jan 1, 1960

By T. E. Leontis

ONLY a limited amount of information has been published on the effect of thorium as an alloying ingredient in magnesium. McDonald13'2 showed that the addition of thorium in amounts up to 3 pct increases significantly both the ductility and the strength of rolled magnesium sheet. A recent publication by Sauerwald" indicates that thorium contributes strength and creep resistance at elevated temperatures to magnesium in both the cast and wrought states. The observations of Sauerwald are confirmed in this paper, which presents the results of a systematic study of the effects of compositional variation on the tensile properties, creep resistance, conductivity, density, and metallography of Mg-Th alloys containing up to 50 pct Th both in the sand-cast and in the extruded states. The effect of the addition of cerium to Mg-Th alloys is also reported. Experimental Methods The alloys studied in this investigation were pre.pared in small laboratory melts according to the melting practice described by Nelson4 as the crucible method. Electrolytic magnesium was used as the starting material to which the thorium* was introduced in metallic form. It was observed that the behavior of thorium in molten magnesium with respect to reaction with protective fluxes is similar to that of rare-earth metals. In order to obtain the highest possible alloying efficiency, it is necessary to use non-MgC1, fluxes and to apply all the precautions described by Marande6 for melting, alloying, and casting magnesium-rare-earth alloys. .Under these conditions it is possible to obtain an alloying efficiency in the range of 85 to 95 pct. The Mg-Th-Ce alloys were made with cerium of the highest purity available, not with the commercial product "misch-metal" which contains approximately 50 pct Ce. The total rare-earth content of this material was 97.1 pct, of which 0.3 pct was rare-earth metals other than cerium; the major impurities comprising the balance were iron and magnesium. The thorium and cerium contents of each alloy were determined chemically. Test bars 6% in. long with a 2% in. long reduced section of % in. diam were cast in sand molds using a four-baf pattern. In most cases, a 3 in. diam extrusion billet 10 in. long was cast in a steel mold from the same melt used for making the sand-cast test bars. For the higher thorium alloys, it was necessary to remelt the foundry scrap from the test bars in order to make the extrusion billets. The billets were scalped to a diameter of 2 15/16 in. and the ends faced to a length of 9% in. as limited by the size of the extrusion container. The alloys were extruded into % in. diam rod on a 500-ton direct-extrusion press. The details of the extrusion process are as follows: Billet preheat 925°F (2 to 16 hr) Container temperature 900 °F Die temperature 900°F Extrusion speed 10 ft per min Reduction ratio 36:1 Percent reduction 97.3 Alloys containing up to 10.2 pct Th were preheated at 925°F for 2 hr; all alloys with higher thorium contents were preheated for 16 hr. In order to establish the effect of extrusion temperature, billets of

Jan 1, 1953

By Bengt Helmerson

A new tankhouse was started in January 1959 at the Copper Refinery of the Boliden Co., Skelleftehamn, Sweden. In early 1961 a semiautomatic machine for looping and straightening of starting sheets was introduced to substitute previous manual operations. The machine as well as consequent, racking and handling is described. Finally, economic benefits achieved and new constructions for the future are discussed. HISTORY Tankhouse operations at the Boliden Co. 's Smelter in Skelleftehamn started in 1932 on a scale that since then has been gradually increasing. In order to rationalize the operations, a new tankhouse was erected. It went into production in January 1959 and was designed for a yearly production of 35,000 metric tons at a current density of 16 amps per sq ft. Already from the beginning, however, the tankhouse has been run with a current density of 21.5 amps per sq ft, corresponding to a maximum capacity of 50,000 tons a year. During the time of planning of the new tankhouse, due consideration was given to the possibilities of mechanizing the operations. New ideas could be and were actually tested on full or pilot plant scale in the old tankhouse. In that way we developed a system for the cathode handling including washing, weighing, and transportation. A system using forklift trucks in combination with trailers and overhead cranes has been developed for transportation and racking of anodes and also for handling of anode scrap. With respect to the electrolyte, circulation and temperature control are partly automatic. Special attention was paid to the production of starting sheets, which operation normally requires a great number of man hours, and it was made the object of a particular survey as to the best ways of straightening starting sheets, attaching loops to the sheets, and so forth. As a result, a machine was designed during 1957-58 and built in our own shops. After a period of tests, the new equipment was put in operation commercially on the 10th of April, 1961. Since this date the machine has produced about 2 million starting sheets without interruption and has been the only source of looped starting sheets for the tankhouse. GENERAL DESCRIPTION Fig. 1 shows all the major parts of the system. These parts are: slitting machine with feeding table (I), standard roller leveler, type Ungerer (2), tilting roller table (3), conveyors for sheets and suspension bars (4, 7), storage of suspension bars (51, punching and stitching machine (6), two lift-turn-tilt tables (8) for discharging the starting sheets, two rack conveyors (9) for sheet assemblies. Included are a hy-daulic pump station and panels for pneumatic and electric controls. SLITTING AND STRAIGHTENING The machine is fed by hand by a man sitting in front of the slitting-machine table, Fig. 2. This operator inserts one sheet at a time into the slitter. After being trimmed, the sheet is automatically conveyed to the following step of handling, straightening. The slitting machine cuts away about 8 mm of the upper and lower parts of the sheet (in relation to its original position in the stripper section) for two reasons. The first one is to give the machine sheets of uniform dimensions; the second one is a matter of quality. Normally the starting sheets as stripped have a thick edge at the bottom end. This part would collect anode slimes and might also cause short circuits when inserted in the cells without trimming. The straightener used is of German construction

Jan 1, 1967

J. M. Wadsworth,' Okmulgee, Okla. (written discussion).—It seems to me that thc young man must first be absolutely sure that the work he has taken up is to his liking and then I would advise that he get into the practical end of it and learn as much about it as he can as fast as he can. For instance, in the refinery business the college man, graduated in chemical engineering, should ground himself by going through the various departments in a refinery and working in them until he is thoroughly familiar with the operating problems. In a short time he would be able to apply many things which appear in the abstract form in his college work and this would opcn up an opportunity for him to capitalize on them, promoting his own interest. I do not criticize the present-day college men as a class, but I have found that many of them come into your plant with the idea that mere possession of a diploma should insure rapid promotion; in a short time they are impatient and usually leave. We have found in employing men that the single attribute most difficult to find in them is a lot of energy and whole-hearted interest in the work at hand, and it seems to me that if a man combines these with a careful technical training he should be fairly well equipped to gamble on his future. They must learn that the biggest satisfaction to be gained in life is in their work. Procedure for Attaining Objective of Young Petroleum Engineer H. B. Fell,+ Ardmore, Okla. (written discussion).—Of course, the first thing to be ronsidered in any proposition is the ultimate objective that is desired to be attained. 1 presume that the desired objective of most of the young men graduating in petroleum engineering will be that of chief executive of one of the companies in the petroleum industry, or one of the allied industries, or to become an independent oil producer, or oil refiner, or possibly an oil distributor. The next phase then to be considered is the procedure which should most logically be followed to attain the objeckive of the indivitlual, since in these cases these young men will have been trained in a course in petroleum engineering and it would logically be presumed that the attainment of their objective should be through the operating end of the branch of the business with which they are connected. The operating end is, of course, the department of each branch of the business that develops the resources, or refines the products, or distributes the products, from which the profits are derived, and is a part of any business which is filled with enough interesting work to appease the desires of the most ambitious young men. In order to get the best possible training it would appear to me that the place for a young man to start after graduation would be at the bottom of that branch of the industry which he expects to follow. For example, if he is going in the producing end he can gct no better training than is secured by starting as a roustabout in the ficltl, where he romes in constant rontact with the character of work that is necessary

Jan 1, 1928

By F. P. Nichols, F. A. Renninger

At one time, mineral aggregates were considered physically and chemically inert substances whose junction was that of an inex-pensive, easily obtainable source of bulk. This philosophy applied regardless of the use to which the aggregate was put. Research approaches dealing only with such gross physical properties as hardness, toughness, impact resistance, etc., dominated the early growth years of the industry and influenced specifications to a large extent. The accelerated pace of highway construction, which began toward the end of the depression years, focused attention on the need for extensive aggregate research. The realization in the early 1940's that aggregates interacted chemically as well as physically with their environment provided the stimulus necessary to translate the drab, systematic aggregate technology of the early 20th century into the changing, dynamic, challenging field it is today. Current research problems are discussed in detail. These efforts being pursued by contract research organizations, universities, governmental agencies, and industry transcend many fields. The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Almost 2 billion tons of mineral aggregates are quarried or mined, processed, and sold yearly in the United States alone.= The largest uses to which this vast tonnage is subjected are as ingredients of portland-cement concrete, bituminous concrete, and dense-graded aggregate-base course mixtures in the highway and building construction fields, two industries closely related to the expenditure of public funds. It is for these uses, partially in justification for the expenditures of vast sums of public funds, that mineral aggregate research truly finds its emphasis. The research efforts expended relative to the highway and building construction uses to which mineral aggregates are subjected are those of primary concern to the industry. These efforts, while of direct consequence to the industry due to the volume market represented, are of interest as well to public agencies, universities, and contract research firms. All actively conduct research, exchange information, and make contributions to the overall knowledge relative to aggregate usage and limitations. The research efforts of the mineral aggregate industry is the subject to be discussed throughout this paper. It covers all aspects of highway and building design, construction, and technology. The effects of research pertaining to quarrying and mining methods, blasting and processing techniques, storage and handling facilities, and equipment employment and development have left their mark on the crushed stone and sand and gravel industries. Such specialized efforts have resulted in dramatically increased production rates which in turn have served to keep costs, and hence prices, down. Despite the many inflationary pressures over the years, the cost of a ton of aggregate today is little more than it was 25 or 30 years ago. Mention is made of these efforts simply to emphasize the diversity of research in the mineral aggregate field. The remainder of this paper focuses on the complexity of what might be termed "product knowledge" research.

Jan 1, 1971

By H. Larson, J. Chipman

The ferrous and ferric oxide concentrations of slags, expressed as j = Fe+++/(Fe+++ + Fe++), have been established through gas-slag equilibrium at 1550°C in a range of oxygen pressure of 10-I to 10-9 equilibriumatm. The value of j is increased by basic additions (BaO, CaO, MgO, MnO) and decreased by acidic oxides (SiO2 and TiO2). Oxygen pressure is shown graphically as a function of composition for slags which are analogous to those at the slag-gas interface of the open hearth furnace. THE progress which has been made in recent years in understanding the chemistry of metallurgical slags has been based largely on studies of slag-metal and slag-gas equilibria. There is a considerable body of knowledge which is applicable to reactions occurring at the slag-metal interface in open hearth steelmaking. There is little information concerning reactions of the slag with the furnace atmosphere and hence little basis for an understanding of the transfer of oxygen, sulphur, or hydrogen between gas and slag. The oxygen pressure of the open hearth atmosphere is normally of the order of 10-1 to 10-3 atm which differs by several orders of magnitude from that of about 10" atm at the slag-metal interface. The chemical properties of the slag, for example, the ratio of ferric to ferrous iron and the ability of the slag to hold sulphur in solution, are greatly affected by changes in oxygen pressure. This investigation was undertaken to enlarge our knowledge of the effect of oxygen Pressure on steel-making slags. Using air or controlled mixtures of CO a CO2 a range of oxygen Pressures from 10.' to 10.' was covered. Review of the Literature There are only a few references in the literature which pertain directly to this investigation. The most important is that of Darken and Gurry1,2 on the system iron-oxygen. This work included the determination of the phase diagram of the system and also a study of the field of homogeneous melts and their oxygen pressures. Their apparatus and procedure were very similar to that used in this study. Iron oxide was melted in a platinum crucible under an atmosphere of CO2:CO, CO2:H2, H2O, CO2, air or O2 depending upon the partial pressure of oxygen desired. After equilibrium was reached, the sample was quenched and analyzed for ferrous and ferric oxide. By appropriate calculations these authors were able to determine the oxygen and iron activities in the various slags, heats of formation of the oxides of iron, and heats of solution of iron and oxygen in the liquid slags. In a subsequent paper' the same authors made a less thorough investigation of the effects of additions of lime and manganese oxide on the composition of iron oxide melts. Only a few experiments were made and those in a narrower range of temperature and oxygen pressure. Darken' has investigated the fusion temperature of iron oxide in contact with silica under various atmospheres. He found that the temperature changes from 1120° to 1447°C as the gas composition changes from CO2/CO equal to 20.8 to pure oxygen. A comprehensive paper by White" predates the work of Darken and Gurry. The decomposition of ferric oxide into oxygen and lower oxides of iron was studied from 1000° to 1650°C and under oxygen pressures from 2 to 76 cm of mercury. The effect of

Jan 1, 1954

By B. K. Larkin, H. R. Bailey

One of the most complicated and potentially one of the most promising secondary recovery methods is that of underground combustion. A number of field tests1,2,3 have been performed recently, apparently indicating that the underground combustion process is technically feasible. Relatively little has been published concerning laboratory or theoretical investigations of the underground combustion process. A few results of laboratory tube runs have been published4,5 and these data are valuable in understanding the process. The tube run data also emphasize the complexity of the thermal recovery process. Under various conditions, problems in heat transfer, multiphase fluid flow and combustion rates arise. For example, at low temperatures the combustion process proceeds so slowly that the front cannot be propagated. It is a problem in heat transfer to predict what injection rate of air is necessary to sustain combustion in a particular reservoir. Certain fluid flow aspects of underground combustion have been studied by Wilson, et a13. In the development of some of the flow equations, assumptions of adiabatic combustion were made. Vogel and Krueger1 have devised an analog model of the heat conduction process for a constant temperature cylindrical source moving radially outward in a homogeneous conducting medium. Jenkins and Ramey7, in a discussion of the Vogel and Krueger paper, present an analytical solution of a heat conduction problem related to problems considered by Vogel and Krueger. In the present paper an idealized model of the heat conduction problem is considered, which is more general than the model of Vogel and Krueger or Jenkins and Ramey. In particular, initial well heating, vertical heat losses and arbitrary frontal velocities are included. Equations for the temperature are obtained in terms of integrals. These integrals have been evaluated numerically for the case of frontal movement corresponding to a constant air injection rate and the case of constant frontal velocity. These results are presented graphically. From these graphs one may estimate conditions under which nearly adiabatic temperatures are obtained. The application of these results requires some knowledge of reservoir thermal properties, combustion rates and residual fuel content. Assuming no vertical losses it is possible to obtain explicit evaluations of these integrals in the linear con- stant velocity case and in the radial case corresponding to a constant air injection rate. PRESENTATION OF RESULTS The geometry of the radial system is illustrated in Fig. 1 where the reservoir is represented as a slab of thickness h. By making an energy balance for an infinitesimal volume, one obtains the following equation. T= x T+F(z.r).........(1) where F (z,r) =HWv1/pc (r-r1), if z h/2 = 0, if z >h/2 . In Eq. 1, V- represents the Laplacian operator and 8 is the Dirac delta function. Eq. 1 is the well-known diff-sion equation with a source term and may be applied to a linear system. For example, if the source is moving in the direction of the x axis, then the argument of the delta function is x - 1,. In deriving Eq. 1 the following approximations were made concerning the actual combustion process: (1) all heat transfer is by conduction in a homogeneous medium, (2) the formations bounding the reservoir have the same thermal properties as the reservoir, (3) the combustion fuel is consumed instantaneously as the front arrives, (4) there is a constant fuel concentration

By C. R. Fast, George C. Howard

Laboratory and field testing of various squeeze cementing techniques and materials revealed that many improvements could be made in squeeze cementing operations. The use of a slow-pumping squeeze cementing procedure permitted the control of the quantity of cement displaced into a formation and aided in obtaining a high final squeeze pressure. Field testing indicated the desirability of obtaining high final squeeze pressures, the need for improved formation breakdown fluids, and the necessity of controlling the pressure differential during testing after a squeeze job. INTRODUCTION During the past few years, squeeze cementing operations have been investigated, both from the theoretical as well as the practical point of view, in an effort to arrive at some solution to the many and varied problems that arise with this type of operation. A review of well files indicated that in many instances, wells were being squeeze cemented four and five times before a satisfactory pressure buildup was obtained. There seemed to be considerable variation in opinion as to the proper method of squeeze cementing, as well as disagreement as to the proper breakdown agent, the quantity of cement that should be used, type retainer and length of WOC* time that was necessary. Consequently, it was deemed advisable to approach this problem theoretically, field testing each idea developed in hopes of eventually arriving at a squeeze cementing procedure that would give reasonable assurance of a successful job after one squeeze cementing operation. This investigation was. therefore, divided into two broad headings: (1) Preliminary studies, which include both theoretical and laboratory studies, and (2) Field investigations to determine the proper squeeze cementing methods. PRELIMINARY STUDIES Overburden Pressure Studies Squeeze cementing problems are so intimately related to the earth's overburden pressure that solutions to them are very difficult, if not impossible, without an understanding of the nature and magnitude of the overburden pressures encountered at the depths of producing wells. It was thus felt that the first approach to research on squeeze cementing should be made through a study of these pressures. Since there has been rather loose usage of a number of the terms related to overburden preasure by different writers, the terms to be subsequently used are defined here. Theoretical overburden pressure is the calculated pressure at any given depth exerted by the theoretical weight of overlying formations as calculated from the average rock density. Fluid displacement pressure is that pressure at which fluid can be injected into a formation after it has been broken down. It may be more or less than the theoretical overburden pressure. Formation breakdown pressure is that pressure at which a formation parts or breaks and is usually thought of as fluid displacement pressure plus rock strength. Breakdown agent is that fluid with which the formation is fractured. The first step in the study of the earth's overburden pressures involved a review of pertinent technical literature. The general opinion expressed was that the overburden pressure gradient of the earth's formations is roughly 1.0 psi per foot of depth, and that application of sufficient pressure to stratified formations. will cause them to part at or parallel to the bedding planes. The second step in the study of overburden pressures involved a study of available well data in an effort to obtain some definite information as to the actual values experienced in the field for the above mentioned terms. Data from 115 cement squeeze jobs in the Gulf Coast area and 46 cement squeeze jobs and acid jobs in the West Texas-New Mexico area were closely analyzed. The analysis of these data showed that the average formation breakdown

Jan 1, 1950

By R. J. Blackwell, J. R. Rayne, W. M. Terry

This paper presents results of an experimental investigation of factors that control the efficiency with which oil is displaced from porous media by a miscible fluid. The study was made to elucidate the relevant processes both on microscopic level (within individual or between neighboring pore spaces) and on macroscopic level (within a large sand body). Mixing of miscible fluids on the microscopic level was studied in sand-packed tubes. It was found that molecular diffusion is the dominant dispersion mechanism for reservoir conditions of rate, length and pore sizes. Macroscopic channeling was studied for various mobility ratios in reservoir mode1s scaled to relate viscous, gravitational, and diffusional forces. The formation of channels was due to viscous firzgering, gravity segregation and variations in permeability. With adverse mobility ratios, it was found for reservoirs of realistic widths that diffusion will not be effective in preventing the formation and growth of fingers, even in homogeneous sands. At sufficiently low rates channeling was eliminated by gravity segregation in tilted reservoirs. The dependence of recovery on mobility ratio, length-to-width ratio, flow rate and angle of dip is presented. INTRODUCTION Oil recovery by solvent flooding is finding increasing application in the field. While the process promises high recoveries from the region swept by solvent, under adverse conditions only a small fraction of the reservoir volume may be swept at the time solvent breaks through to the producing well. Further, the high cost of the solvent encourages its use only as a bank whose size must be kept at a minimum. Thus, two important questions arise: (1) what fraction of the reservoir can be swept, practically, by solvent? and (2) what is the minimum size solvent bank that can be used to carry out the displacement? The answers to these questions require knowledge of both macroscopic channeling processes and microscopic mixing processes. The studies described here were carried out to gain this knowledge. Microscopic mechanisms which cause mixing will be discussed first, because an understanding of these mechanisms is necessary for proper interpretation of the experimental work on channeling described later. INVESTIGATION OF MICROSCOPIC DISPLACEMENT PHENOMENA FOR MISCIBLE FLUIDS The questions to be resolved concerning microscopic displacement behavior are: (1) how much mixing occurs between oil and solvent in the direction of flow? and (2) does the solvent completely flush the oil from the pore spaces in the region invaded by solvent? The classic work of Sir Geoffrey Taylor' and its extension by Aris2 have shown that it is possible from theory to describe the amount of mixing in single straight capillaries when solvent displaces a fluid of equal viscosity and equal density. Aris showed that the lengths of the mixing zones, 81, corresponding to the 10 per cent and 90 per cent concentration levels of the solvent can be calculated from the formula, 81 = 3.62 \/Kt, .........(1) where 8l is the length of the mixing zone, cm; t is the time, sec; and K is the effective dispersion coefficient, cm2/sec, given by K/D = 1 + (1/48) (au/D)2......(2) where a is the radius of the capillary, cm; D is the molecular diffusivity, cm2/sec; u is the average velocity

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By Bradley Stoughton

AT THE meeting of the Board of Directors on May 20, the resignation of Bradley Stoughton as Secretary of the Institute was presented and regretfully accepted by the Board. The letter of resignation follows : Gentlemen: About two years ago, I indicated to the President and some members of the Board my belief that the office of Secretary of the Institute should not be a permanent one. It is my observation of events, not only in our own Institute, but also in several sister societies, that too long a tenure of office by the Secretary inevitably leads to a situation which is not good either for him or for the society. After submitting this in writing to the Directors on February 17, 1920, I was overpersuaded by members of the Board to defer resignation until a more convenient time for the

Jan 1, 1921

By Faustino Roel

AMONG the problems confronting the mining engineer in Mexico in recent years, labor conflicts have come to occupy s prominent place. Each day they have become more serious and frequently have caused- the ruin of companies. It is therefore necessary for the engineer to understand the Federal Labor Law, the rights and obligations of companies and of their workmen, and the reasons for conflicts; to keep in mind the expense which may be caused companies; and to endeavor to avoid difficulties as far as possible. Our labor legislation is primarily to protect the workman and the constant tendency of the tribunals, including the Supreme Court of Justice, is to support the work- man in his demands against employer$, even at times granting him more than he asks, with no limit other than the economic capacity of the company to com-

Jan 1, 1937