Search Documents

By Douglas R. Piteau

Douglas R. Piteau (Engineering Geologist, De Beers Corp., Kimberley, South Africa; Presently Consulting Specialist at Nchanga Mine Open Pit, Chingola, Zambia)-Mr. Lutton is to be commeneded on his analyses and presentation of such practical data which can be used for predicting a preliminary optimum slope angle in rock. It appears that he assumes all slopes analyzed to be straight. Although there are overriding factors which affect the general slope configuration, such as structural discontinuities, ground water, and other environmental factors such as weathering conditions, regional stress, etc.,8 the affects of plan geometry under certain conditions also can be of outstanding importance. In investigation of natural slopes, for example, the effects of plan geometry are not entirely appreciated and it is in this respect that discussion is given. Experience in southern Africa has shown that the overall geometry of surface openings in rock, particularly those with dimensions of the order of 1500 ft or less, i.e., where radii of curvature of the slopes are less than, say, 700± ft, must be considered in rational slope-stability analyses. That is, the slope angle is not only a function of slope height, strength of the mass, and geometry of structural discontinuities, but also is dependent upon the plan geometry of the local slopes and the plan shape of opening. Technically speaking, adequate analysis of the slope must be three-dimensional, the third dimension being that of overall plan configuration and the analysis must incorporate its subsequent effects. However, current theories of slope stability all deal with the slope as a two-dimensional problem, i.e., a slice of unit length of an infinitely long slope is considered for a condition of plane strain. In this the tacit assumption is made that the plan radii of the crest and toe of the slope are infinite and no attention is given to the plan geometry of the slope. Clearly this is not the condition encountered in practice, particularly in open pit mining where excavations, relatively speaking, can be small and where these radii of curvature accordingly can have important affects on the slope stability. This is illustrated by the analyses of Piteau and Jennings 9 of the natural slopes which had developed around pipes of four diamond mines in the semiarid Kimberley area of South Africa. Although these slopes consist of dolerite overlying shale, the values of the slope angles of all the pits were corrected for a height of slope of 320 ft assuming that no dolerite occurred. This brought the data onto a comparable basis. These data were analyzed statistically and a clear empirical relationship, as is shown [in Fig. 4], is seen to have formed between angle of slope and curvature of slope, i.e., the angles of slope are greatest where the radii of curvature are least. Also, it can be seen that the slope of each line is different, indicating that the plan shape of the open pits also are significant, the curve being steepest for the open pits which are more circular in shape in contrast to those which are more elongated. The effect of slope curvature on the average angle of slope for the two extreme radii of 200 ft and 1000 ft for all four open pits is 39.5° and 27.3°, respectively. Hence, the concave curvature effect represents an average increase in slope angle of 12.2° from the essentially straight slope. In quantitative terms in Mr. Lutton's Fig. 2, this represents displacing the curve for a 320-ft pit from the second curve from the bottom (i.e., shale in subtropical climate) to that of the third from the bottom (i.e., quartzite in temperate environment).

Jan 1, 1972

By Patricia J. Rand, Kailish Narayan

Atlantic Richfield Co. began operating a commercial uranium solution mining project in April 1975, in Live Oak County, Tex., 10 miles southwest of the town of George West. The operation is designed to produce 250,00 lb of U308 per year and is jointly owned by Atlantic Richfield Co., Dalco, and U.S. Steel. The proprietary process employed in this operation consists of injecting an alkaline leaching solution into the ore-bearing formation through a pattern of injection wells. The uranium-bearing solution is then removed through producing wells using submersible pumps in central production wells. The produced solution is pumped through a pipeline to the plant area where the uranium is extracted. The barren solution is refurbished and returned to the pattern area for reinjection. The injection field and plant site are located in the drainage of Spring Creek, a small intermittent stream tributary to the Nueces River. Land use in the area is primarily agricultural cattle ranching and farming---but several producing gas fields are present in the areas as well. A nine month enviromental baseline study was conducted on the property beginning in Feb. 1975. Plants and animals of the Clay West area were identified and representative terrestrial and aquatic communities were analyzed. Physical and chemical parameters of the soils were described and analyzed. The surface and underground waters were analyzed chemically; radionuclides, heavy metals, nutrients, and pesticide concentrations were measured in the creek sediments; bacteriological measurements were made in creek water and sediments; radionuclide and chemical levels in plants and animals, both terrestial and aquatic, were measured. These studies, though not required by existing, state or federal laws, were considered necessary to assess the existing conditions before operations began on site. The in-place leaching technique for uranium mining eliminates the enviromental disturbances associated with open pit or underground mining. No grinding and crushing of ore is needed, nor are large tonnages of waste tailings produced. Surface subsidence is not expected since less than 5 lb of uranium is present per ton of rock and even complete removal of such small amounts should not cause subsidence. Solution mining has fewer environmental problems than conventional mining. Members of the Texas Water Quality Board recognized the differences which exist and have recently formulated new environmental control procedures which apply specifically to solution mining. Some of the solution mining activities which are of particular concern are discussed in the following pages. Process Description The produced uranium-bearing solution is pumped through a pipeline from the pattern area to the plant area. The first pattern area consists of a nest of 125 fluid injection, production, and monitor wells [(Fig. 1)]. Injection wells have 4-in. casings and are spaced 50 ft apart on a square grid. Production wells have a 6-in. casing and are located in the center of each square. A block flow sheet of the plant is given in [Fig. 2]. The produced solution goes through parallel trains, each consisting of a carbon column and an ion exchange column in series. The carbon column removes any sand present in the produced solution and the ion exchange column extracts the uranium. The depleted solution is treated with chemicals and returned to the field for reinjection. The uranium retained in the ion exchange column is removed periodically with a sodium chloride solution. Uranium-bearing solution from the ion exchange column is passed through a charcoal column for removal of impurities and then to a precipitation tank where the uranium is precipitated as yellowcake slurry. The yellowcake slurry is clarified, filtered and dried to produce a granular yellowcake product. Environmental Considerations Sources of waste solutions to storage reservoirs, the backwash reservoir and atmospheric discharges are shown in the block flow sheet [(Fig. 2)]. These waste solutions pose a relatively small problem and are adequately controlled by conventional means. There is one area, however,

Jan 1, 1978

By W. Rostoker, H. Nichols

It has been demonstrated in previous work1'2 that wetting of aluminum alloys by liquid mercury can cause fracture to occur with substantial suppression of prior plastic flow. This has been interpreted as the action of a critical liquid species in reducing the cohesive strength of a stressed solid at sites of potential crack nucleation. In this way the critical transverse stress for fracture nucleation is reached at much lower stresses than is normally the case. The stresses for both fracture nucleation and fracture propagation are depressed by the same mechanism. In so doing the plastic-energy component of fracture energy is reduced to a level which is of the same order of magnitude as the surface, interfacial, or cleavage energy. Recent work2 has illustrated the influence of dispersed precipitates, cold work, and combinations of these on brittle fracture associated with plastic strains of the microyield order of magnitude. This has been rationalized in terms of the contribution of internal microstress fields to the stress magnifications at points of obstruction of active slip bands in a stressed metal. The presently reported studies on an Al-4-1/2 pct Mg alloy amplify this subject by introducing thermal-mechanical conditions which can produce strain aging. As amply demonstrated by Phillips, Swain, and borall, the tensile behavior of aluminum alloys containing magnesium reveals a yield-point elongation and successive discontinuous elongations over the whole plastic-strain range. This gives a stepped or serrated character to the stress-strain diagram. The yield-point elongation is not temperature-dependent. On the other hand, the discontinuous extensions in the plastic-strain range are gradually suppressed by lower temperatures of testing. At -78"C, only the yield-point elongation persists. The yield-point elongation itself can be suppressed by rapid quenching to room temperature from an annealing temperature of 500°C. The argument presented by Phillips et 1. and Cottre114 is that the yield-point elongation derives from surmounting at a critical stress the restraint to slip by grain boundaries which have been reinforced by appreciable magnesium-atom segregation. The serrated character of the plastic-strain range is the result of rapid strain aging during the test. This is made possible by the inevitable proximity of magnesium atoms to any dislocation line. In the Al-4-1/2 pct Mg alloy there is one magnesium atom for every twenty-two aluminum atoms and, with a coordination number of 12, a magnesium atom is on the average only about two atomic distances from any given lattice site. Rapid strain aging is therefore a reasonable expectation. A study of mercury embrittlement of the Al-4-1/2 pct Mg alloy (commercial designation 5083) provides an opportunity to relate the interplay of grain size, grain boundary restraint to slip and strain aging in the brittle-fracture process. One lot of commercial sheet material of 0.125-in. thickness was used for all of the tests. The specimen shape and test procedures used were the same as those described in a previous publication.2 A range of grain sizes between 0.0057 and 0.0125 mm was produced by various combinations of plastic prestrain and annealing. The coarsest grain was somewhat elongated in shape. In this case the measurement was taken in the direction transverse to the axis of tension as more meaningful to a brittle-fracture process. In the annealed condition, specimens wetted with mercury failed with zero permanent elongation at stresses slightly below the normal yield point, i.e., stresses at 0.05 to 0.2 pct strain. Since this occurs before yield-point elongation can begin, fracture derives from slip contained within individual grains and restrained from propagating across grain boundaries. No significant difference in wetted fracture stress was observed between specimens which had been water-quenched or furnace-cooled from the annealing temperatures. This signifies that the degree of magnesium segregation at grain boundaries

Jan 1, 1964

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs.' Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster" and was first reduced to practice by the experimentation of Welge. In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid Phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always ereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs.' Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster" and was first reduced to practice by the experimentation of Welge. In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid Phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always ereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By R. I. Jaff, H. R. Ogden, D. J. Maykuth

A phase diagram for alloys containing from 0 to 66.9 pct Mn was determined. Two compounds, tentatively labeled 6 and y, were found in this range. The 6 compound is located at about 66.9 pct Mn and melts congruently at 1330°C. The ? compound has a composition near 53 pct Mn and originates in a peritectic reaction at 1200°C between liquid and 6. ß and Y enter into a eutectic reaction at 1175°C. The ß phase field terminates in a very sluggish eutectoid reaction between a and ? at 550°C. MANGANESE is one of the important alloying addition elements to titanium. As a ß-stabiliz-ing addition for a-ß and ß alloys, it provides high strength with adequate ductility.' Two of the earliest commercial alloys contain manganese as a major alloying component.' The earliest published data on the constitution of Ti-Mn alloys was that of Wallbaum,~ who reported the existence of the compound TiMn2. The transformation range of commercial-purity Ti-Mn alloys was investigated by Craighead, Simmons, and Eastwood' who found limited a solubility and a lowering of the ß transus to about 790°C at 7 pct Mn. Preliminary work by the authors of this paper, using high-purity titanium, confirmed the ß-stabilizing action of manganese and showed the existence of several intermediate phases in the Ti-Mn system." More recently, McQuillan3 determined the ß transus temperatures for high-purity Ti-base alloys containing up through 4.4 pct Mn. These data are given in Fig. 1. The present investigation covered alloys made with a high-purity base. The constitution of titanium-rich alloys made with commercial titanium has been reported4," by Holladay, Kura, and Jackson. The alloy range covered in the present investigation was from 0 to 69.5 pct Mn. This alloy range extends slightly beyond the composition of the first congruent-melting compound encountered on proceeding from the titanium end of the system. A description of the materials and methods used in the determination of the diagram is given in the Appendix. The partial phase diagram determined for the Ti-Mn system is shown in Fig. 2. Details on equilibria in the titanium-rich alloys are given in Fig. 3. Liquid-Solid Relationships Observations on the cast structures of the arc-melted ingots showed that the terminal solid solution of manganese in ß titanium enters into a eutectic reaction with an intermetallic compound labeled ?. As will be shown later, this compound has a composition around 53 pct Mn. The eutectic reaction temperature was determined as 1175°C by thermal analysis which also showed that the ? phase originates in a peritectic reaction at 1200°C. Fig. 4 shows typical eutectic structures for alloy compositions on both sides of the eutectic composition which is located at 42.5 pct Mn. In alloys over the range of 45.4 through 69.5 pct Mn, a second intermetallic compound, labeled 6, was identifield as the primary phase. This phase consistently increased in amount as the manganese content approached 66.9 pct, and, as shown in Fig. 5, an alloy structure containing 66.9 pct Mn consisted essentially of the 6 compound. Thermal-analysis data indicate a melting point of about 1330°C for the 6 intermediate phase. At 67.0 pct Mn, small quantities of a new, higher manganese-content phase were observed in the form of Chinese-script eutectic particles. Comparison of Fig. 6a and b shows an increasing quantity of this phase as the composition was increased to 69.5 pct Mn. The formation of peritectic ? in arc-melted alloys containing 45.4 pct Mn and above appears to be almost entirely suppressed, as shown in Fig. 7a and b. This is because of the narrow freezing range available for its formation by peritectic reaction and because of the very high cooling rates obtained in

Jan 1, 1954

By J. J. Jonas, J. L. Uvira

Equipment was constructed which permitted the hot compression of 99.8 pct Armco iron and 2.8 pct Si steel at constant true strain rates of 0.05 to 1 per sec over the temperature range 600" to 1000°C. A maximum true strain of 1.9 could be attained, followed by immediate quenching or by isothermal annealing. True stress-true strain curves were obtained, and the steady-state flout stress, a, strain rate, i, and temperature, T, were found to fit the following expression: The constants A, a, n', and AH were determined for the two ,materials. The activation energies obtained for Arrnco iron and silicon steel are 66 and 80 kcal per mole, respectively, and approximate those for seu- diffusion and for creep. This indicates that hot compression is a diffusion-controlled thermally activated process. THE hot compression of iron and steel is usually carried out in the austenite temperature range,1"7 as this is the one of greatest interest with respect to industrial hot working. However, a disadvantage of testing in the austenite range is that the hot-worked structure is destroyed by the phase transformations taking place during cooling. The present study was therefore carried out in the ferritic temperature range, and the hot-worked substructures were preserved by rapid quenching after deformation. The substructural results will be described in a separate paper, and the present communication is restricted to the strain rate/stress/temperature relationship observed during hot working. The results of hot-compression testing are usually given in the form of true stress/true strain curves, with a different curve for each temperature/strain rate ~ornbination.',~,~ Sometimes simple algebraic equations are fitted to the curves, so that certain extrapolations or interpolations can be performed.1'2'5 These equations are, however, devoid of mechanistic interpretations. The present study was undertaken to show that hot compression can be described by an equation of the type used in creep studies. That is, it will be shown that the temperature dependence of the strain rate in hot working is well-represented by an Arrhenius term, with an activation energy similar to that for creep. Also it will be seen that the stress dependence of the strain rate is similar to that for creep EXPERIMENTAL METHOD AND MATERIALS The investigation was carried out with the following three ferrous materials: 1) Armco iron; 2) Armco iron with 0.26 pct Mn; 3) 2.8 pct Si steel. The first two materials were utilized for investigations performed in the temperature range 600" to 800°C; the last one was used for tests at temperatures from 600" to 1000°C. The materials were of commercial purity,* as shown in Table I. Cylinders of five different sizes were prepared by strain annealing. The resulting mean grain diameter was 3 mm in the 1-in. Armco iron and 2 mm in the other sizes and grades. Different ratios of diameter/height were used to enable the determination of the coefficient of friction. The specimen faces were provided with concentric grooves, which acted as lubricant holders during compression, as recommended by English and ~ackofen' and others.2'9 Powdered glass lubricants were applied to the samples before hot compression to decrease friction and barreling, following the practice of previous investigator~.~~~~~~~~ Different mixtures of glass powder were used for each temperature, after the determination of suitable compositions by experiment.'' Equipment for Hot Compression. Hot-compression tests were carried out on an adapted 150-ton vertical hydraulic extrusion press and also on a modified high-temperature creep machine. The modified extrusion press was used for temperatures up to 800°C. The following items were added to the press: a) a high-temperature furnace with built-in upper and lower platens; and b) a transmission assembly, which permitted the attainment of logarithmically decreasing crosshead speeds. These accessories are described in detail in Ref. 11.

Jan 1, 1969

By R. V. Smith

The theory for unsteady radial flow of gas, as simplified by Aronofsky and Jenkins, has been reviewed and compared with actual well performance. This study indicated that the theory should be modified by the introduction of an empirical "rate of flow" function "Y(q)". The expansion of the theory on the flow of gas to include a Y(q) term bridges the gap between the theory of unsteady-state flow of gas and actual gas-well behavior. Apparently, the Y(q) term is a function only of the rate of flow for a given well. The completion factor or skin effect is associated with the Y(q) function in such a manner that at least two or more sets of drawdown or pressure build-up tests are needed to separate the Y(q) function and the completion factor. Since the Y(q) function used in this report represents an energy loss dependent on rate of flow near the well-bore of a gas well which is in addition to the loss required by Darcy's law, the Y(q) function is related to the exponent of the back-pressure curve for a gas well. Techniques and equations are presented which permit the estimation of stabilized and "short-time" deliver-abilities. INTRODUCTION The published theory of radial unsteady-state flow of gas through porous media may be divided into papers1-" which use Darcy's law as a premise and other papers4-7,16-10 which recognize that Darcy's law may not hold for flow into gas wells. Miller8 compared theory based on Darcy's law with actual gas-well behavior and concluded that flow into gas wells deviates from Darcy's law. Houpeurt4,5 in a thorough investigation of flow into gas wells concluded that the flow rate into a gas well is proportional to the difference between the squares of upstream and downstream pressures elevated to a power between 1.0 and 0.5. Houpeurt also concluded that the deviation from Darcy's law is caused by irreversible, kinetic energy exchange between the flowing gas and the porous media. Tek9 presented a complete evaluation of the flow problem in gas wells. Several investigators state that the inclusion of gas compressibility into flow equations based on Darcy's law does not begin to explain the flow problems suggested by gas-well behavior. For many years, natural-gas engineers have realized that gas wells by actual test exhibit behavior which cannot be explained entirely by Darcy's law. Many tests on gas wells have indicated that a value of 0.85 for the exponent in the back-pressure equation is a fair average for many wells. However, Darcy's law either for steady or unsteady-state conditions indicates that the exponent should be 1.0. The purpose of this paper has been to examine this deviation from Darcy's law and to present a reasonable mathematical means of evaluating the deviation. The method presented in this paper combines previous theory with an empirical function to provide a description of gas-well behavior. All equations in this report are for constant terminal-rate-of-flow conditions. While present methods of testing wells usually are not based on this concept, they are believed to approach the constant terminal-rate conditions closely in many tests. However, several gas wells were tested by holding the rates of flow constant in order to approach more closely the constant terminal rate of flow; the results confirm the concepts presented in this paper. REVIEW OF THEORY FOR UNSTEADY-STATE FLOW OF GAS The basic partial differential equation for the flow of natural gas has been given in technical literature; the equation for a cylindrical reservoir with the well in the center is

By K. D. Jacob, W. L. Hill

Fluorine recovery in the United States has been restricted chiefly to manufacture of ordinary superphosphate and wet-process phosphoric acid. However, there is an expanding use of fluorine by industry in the form of hydrofluoric acid. Improved methods for recovering fluorine from phosphate rock would yield an adequate supply of fluosilicates and a substantial contribution to the hydrofluoric acid requirement. THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;' calcium aluminum phosphates such as pseudowavel-1ite; and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island." Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized, most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world. Later these samples were re-analyzed by a new and more reliable method of determining flourine. The revised results with interim additions of new samples, published a few years ago in a brief summary," are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit. Although all rock varieties cannot be classified with certainty, the plotted results exhibit three distinct types of rock in which the F to P2O5 ratio diminishes, remains sensibly constant, and increases, respectively, as the grade of rock increases. Existence of two types of Florida land pebble, Fig. 1, is supported by additional results recently supplied by a producer." Generally speaking, phosphate rock from continental deposits carries considerably more fluorine, and apatite and insular phosphates less, in proportion to the phosphorus content than is required by the formula for fluorapatite. Exceptions to this are apatite from Canada and certain samples of Florida waste-pond phosphate. The manner in which excess fluorine is held and the nature of the carbonate in carbonate apatite are discussed in recent articles. High-grade calcium phosphates with F to P2O5 ratios less than 0.05 have been found in Curacao, Christmas Island," Mexic,13 and elsewhere. The calcium aluminum phosphates and aluminum phosphates aften carry notable amounts of fluorine. The F to P2O, ratio for one sample of pseudowavel-lite concentrate was 0.05." Aluminum phosphate from Grand Connetable Island is very low in fluorine, whereas some aluminum phosphate minerals" carry as much fluorine as highly fluorinated phosphate rock. Fluorine in Domestic Phosphate: The curves shown in the figures permit interpolation of the F to P2O5 ratio corresponding to the midpoint of selected ranges in grade of any one of the several varieties of phosphate. Multiplication of the interpolated ratio by the mid-range grade (P2O5) yields a figure for the percentage of fluorine in this grade. Then, with the use of the mid-range grade, the amount of fluorine held in phosphate reserves can be estimated, see Table I. Accordingly, on Jan. 1, 1950, the fluorine complement of known domestic reserves exceeded 420,000,000 long tons of the element. A previous figure," deduced in 1940 by a simpler procedure

Jan 1, 1955

By P. K. Koh, G. C. Dunn

Si-Fe single crystals in a number of selected orientations were cold rolled 70 pct and analyzed to obtain quantitative (110) pole figures. Stable end orientations were ddetermined, and the effect of orientation on deformation behavior was investigated. WHEN single crystals are cold rolled sufficiently, they rotate into end orientations that are stable or unchanged in position with additional deformation. The end orientations of heavily cold-rolled iron crystals, positioned in holes in copper to limit lateral flow and to simulate polycrystalline conditions during deformation, were determined by Barrett and Levenson.' They found that the sum of the end orientations, a pole figure for all the crystals studied, reproduced the essential features of the cold-rolled texture of polycrystalline iron. In. an investigation of Fe-Si alloys, Barrett, Ansel, and Mehl' observed little effect of silicon content on the textures of heavily cold-rolled samples. Since alloys with less than 4 pct Si are known to have the same slip systems as iron," it seems logical to expect that they would also have the same end orientations as those for iron. Whereas Barrett and Levenson in their study of single crystals were interested in the problem of the origin of the cold-rolled texture of polycrystalline iron, the present authors are more interested in the final cold-rolled textures of single crystals of Si-Fe from the point of view of their relationship to subsequent recrystallization phenomena which will be reported in another paper. Nevertheless, such points as the tendency of an end orientation not to rotate (stability), the tendency of a pole concentration to spread out, and the tendency of the crystal to widen during cold rolling become interesting separately when the initial orientations are selected already in end orientations. Also the initial orientations having a [I101 axis parallel with the transverse direction, which include the two end orientations (111) [Ti21 and (001) [110], comprise a series that needs further clarification regarding the way such crystals rotate during deformation. Finally the present use of quantitative pole figure methods* represents an advance over the X-ray photographic method employed by Barrett and Levenson in their work on end orientations. The present investigation provides information on the cold-rolling behavior of two groups of Si-Fe crystals: 1-—crystals initially oriented in recognized end orientations for iron crystals with a [I101 direction parallel with the rolling direction, and 2— crystals initially oriented with a [I101 direction 90" to the rolling direction and in the rolling plane. For the second group, there is a 90" range between the (001) [110] orientation and the (110) [001] orientation. Since the 35" portion of this range from (110) [OOl] to (111) Di2] was included in a previous investigation," only the remaining 55" portion from (111) fii2] to (001) [I101 needs further consideration. Also, since both (111) [xi21 and (001) [I101 are end orientations for iron crystals,' there might be a critical orientation* or orientation range be- • W. W. Martin and C. G. Dunno noted that (112) [Till was such a critical orientation. tween them such that early in the deformation an orientation within this critical range splits into two orientations. Upon further deformation, these two orientations rotate to produce a final texture consisting of (001) [1101 and (111) [?i2] components. The end orientations obtained are discussed in connection with the work of Barrett and Levenson, while the observed tendency for lateral flow of crystals in these orientations is treated in terms of the theory of Hibbard and Yen.' Lateral flow according to the theory increases with deviation of the plane containing the rolling direction and the slip direction from a position perpendicular to the plane of rolling. Experimental Procedure Single crystals in sheet form with preselected orientations were prepared by methods that have been described elsewhere." Three lots designated A, B,

Jan 1, 1956

By M. R. Tek, R. L. Nielsen

The scaling laws as formulated by Rapoport relate dynamically similar flow systems in porous media each involving two immiscible, incompressible fluids. A two-dimensional numerical technique for solving the differential equations describing systems of this type has been employed to assess the practical value of the scaling laws in light of the virtually unscalable nature of relative permeability and capillary pressure curves and boundary conditions. Two hypothetical systems — a gas reservoir subject to water drive and the laboratory scaled model of that reservoir — were investigated with emphasis placed on water coning near a production well. Comparison of the computed behavior of these par ticular systems shows that water coning in the reservoir would be more severe than one would expect from an experimental study of a laboratory model scaled within practical limits to the reservoir system. This paper also presents modifications of the scaling laws which are available for systems that can be described adequately in two-dimensional Cartesian coordinates. INTRODUCTION Present day digital computing equipment and methods of numerical analysis allow realistic and quantitative studies to be carried out for many two-phase flow systems in porous media. Before these tools became available the anticipated behavior of systems of this type could be inferred only from analytical solutions of simplified mathematical models or from experimental studies performed on laboratory models. To reproduce the behavior of a reservoir system on the laboratory scale, certain relationships must be satisfied between physical and geometric properties of the reservoir and laboratory systems. Where the reservoir fluids may be considered as two immiscible and incompressible phases, the necessary relationships have been formulated by Rapoportl and others.2-5 Rapoport's scaling laws follow from inspectional analysis of the differential equation describing phase saturation distribution in such systems. It will be recalled that these scaling laws presuppose three conditions: (1) the relative permeability curves must be identical for the model and prototype; (2) the capillary pressure curve (function of phase saturation) for the model must be linearly related to that of the prototype; and (3) boundary conditions imposed on the model must duplicate those existing at the boundaries of the prototype. These three requirements seldom if ever can be satisfied in scaling an actual reservoir to the laboratory system because: (1) The laboratory medium normally will be unconsolidated (glass beads or sand) while the reservoir usually is consolidated. Relative permeability and capillary pressure curves are usually quite different for consolidated and unconsolidated porous media. (2) The reservoir usually will be surrounded by a large aquifer which could be simulated in the laboratory only to a limited extent. (3) Wells present in the reservoir would scale to microscopic dimensions in the laboratory if geometric similarity is to be maintained. In view of these considerations, rigorous scaling of even a totally defined reservoir probably would never be possible. The purpose of this paper is to assess the practical value of the scaling laws in the light of the unscalable variables. This has been done by carrying out numerical solutions in two dimensions to the differential equations describing the flow of two immiscible, incompressible fluids in porous media for a field scale reservoir and a laboratory model of that reservoir. While both the reservoir and the laboratory model were purely fictional, each has been made as realistic and representative as possible. The field problem selected as the basis for the investigation was an inhomogeneous, layered gas reservoir initially at capillary gravitational equilibrium and subsequently produced in the presence of water drive. The laboratory model of this reservoir was designed to utilize oil and water in a glass bead pack. The numerical treatment employed was similar to that of Douglas, Peaceman and Rachford6 and it included both capillary and gravitational forces as

By S. E. Bronisz, Dana L. Douglass

a Uranium was deformed by cold rolling, and the effects of this plustic deformation on the microstruc-ture of the metal were observed by the technique of transmission elecbon microscopy. The recrystalli-zation of selected cold-wmked samples was also studied by this method. The samples were prepared for examination by electrolytic thinning in a standard metallographic electrolyte which has not been previously reported as being used in producing thin foils of uranium. The microstructural changes observed in the a uranium were generally similar to those seen by optical microscopy. The changes in the microstructure of a uranium following cold work and recrystallization treatments have been the subjects of several studies employing optical and X-ray techniques.12-19 These studies indicated that twinning was the redominant mode of deformation at room temperature20 and that the regions of high energy associated with the deformation twins were preferred sites for the initiation of recrystallization.15,18, Recently several workers have prepared thin foils of uranium suitable for examination by transmission electron microscopy.'-lo The foils thus prepared have been used to study fission fragment damage; a particular dislocation reaction,' and gas precipitation." At this laboratory the microstructural changes occurring during the cold working and recrystallizing of a uranium samples have been studied by using transmission electron-microscopy techniques. The foils used in this work were electrolytically thinned in a polishing bath not reported previously in the literature as being used for this purpose. EXPERIMENTAL PROCEDURE The uranium used in this investigation was depleted a uranium sheet 4 mils thick. The results of a spectrochemical analysis of this material are shown in Table I. The as-received uranium was cut into strips, 1 in. wide by 5 in. long, and annealed in vacuo at 600°C for 2-1/2 hr. The resulting microstructure consisted of relatively uniform, equiaxed grains having diameters of 10 to 50 p. Cold Working. The cold-worked samples were prepared by rolling several of the annealed uranium strips to various thicknesses. The strips were reduced 3.5 ± 0.5, 6.0 ± 0.6, 10.0 ± 0.5, 19.5 ± 1.0, and 28.5 ± 2.0 pct in thickness. It was not possible to achieve these reductions with a single pass through the rolling mill, so the strips were turned end for end during the rolling procedure. The cold-rolled strips were stored in dry ice until samples from them could be thinned and examined (within 24 hr after rolling). Annealing. The samples used in studying the re-crystallization behavior of a uranium were obtained by annealing sections of the strips which had been reduced 10.0 and 28.5 pct. These samples were sealed in evacuated Pyrex capsules and were annealed in a tube furnace at temperatures from 200" to 600°C and for times from 1/2 to 2 hr, see Table l. Thinning: The samples from the rolling and heat treatments were prepared for examination in the electron microscope by electropolishing in a bath composed of 25 g chromic acid, 133 ml glacial acetic acid, and 25 ml water. This electrolyte has been used and recommended for preparing specimens for optical metallography It was necessary to mask the edges of the sample with a stop-off paint in order to prevent preferential attack in these areas. The paint used was made by dissolving polystyrene in benzene. The electrolytic cell consisted of a cylindrical stainless-steel cathode placed in a beaker containing the electrolyte, with the sample as the anode positioned at the cell axis. The temperature of the electrolyte was held below 15°C by cooling with liquid

Jan 1, 1963

By M. H. Caron

THE most outstanding property of ammonia liquors, used in the ammonia leaching process is their very limited ability to dissolve all compounds present in reduced ore except nickel and cobalt. Although they do have such a high degree of purity, even the smallest amounts of impurities contaminate the precipitate of basic nickel carbonate that may be obtained from pregnant liquors by straight distillation. Figures have been given in a separate paper regarding the extent of such contamination. The product of straight distillation is likely to contain small amounts of Fe, Mn, MgO and SiO2 as well as some sulphate and sulphide. The sulphur can be readily eliminated by calcination of the product at the proper temperature and MgO and SiO2 by reduction and melting of the metal with a suitable flux. After such treatment the metal is relatively pure, and the iron and manganese content will be very small. The cobalt content, however, may vary considerably, depending upon the ore treated. The metal obtained from pure true garni-erite ores usually has only a small cobalt content of less than 1 pct. Metal obtained from medium grade iron-rich nickel ores may show cobalt values from 2 to 3 pct, and the alloy obtained from laterite is likely to contain as much as 10 pct cobalt. By proper treatment a good deal of cobalt may be recovered from lateritic nickeliferous iron ores, and cobalt will become the major constituent of the pregnant liquor if asbolan ores or similar products are treated. The pregnant liquor of "run of mine" nickel ores may have a pinkish shade, indicating the presence of cobalt. It is evident that from such liquors the metals should be recovered separately. Even if cobalt is present in only very small amounts, it would probably be economically justifiable to recover both metals as pure as possible if a suitable process could be devised. The author has made investigations along this line and has patented some processes adapted to the treatment of this type of solutions. Selective Dissolution of Nickel from Basic Nickel Carbonate Containing Some Cobalt: Basic nickel carbonate obtained from true garnierite ores by straight distillation of the pregnant liquors, always contains some cobalt as well as the normal impurities. In. order to improve the quality of the nickel product and to recover most of the cobalt, the following process has been devised. By using liquors with a low CO2 to NH3 ratio, nickel can be redis-solved preferentially to cobalt. It is not a sharp and clean separation but a selective one, for the bulk of the nickel may be redissolved with a small amount of cobalt, and a small residue may hold the bulk of the cobalt. The greatly increased cobalt content of the residue is indicated by a pronounced olive green color, in contrast with the light green color of pure basic nickel carbonate. The following example is given from Dutch patent No. 52788, Klasse 40a. 43 granted June 17, 1942: The original precipitate contained about 0.55 pct cobalt calculated on total nickel + cobalt. Eight hundred and fifty grams of the basic nickel carbonate were redissolved in leach liquor containing 7.12 pct NH3 and 2.12 pct CO2. The weight of the dry residue was about 3.5 pct of the original weight. By analysis it was found that the residue contained: Fe 1.93 pct, Co 6.01 pct, Ni 34.87 pct and also a certain amount of silica. The clear filtered blue liquor was distilled and the precipitate of basic nickel carbonate from this analyzed: Fe 0.008 pct, Co 0.0146 pct, Ni 42.37 pct. It is obvious that this product is considerably more pure, since calculation shows that about 94 pct of the original cobalt remained in the residue. Cobalt and nickel can be recovered by further

Jan 1, 1951

By J. S. Hegwer, P. M. Dunlap

An improved acid for the treatrrzent of sulfate-con-raining limestones and dolomites is described. The acid is designed to reduce he reprecipitation of dissolved calcium sulfate and the possibility of plugging permeable flow channels. In addition, this improved acid has a much lower reaction rate than that of regular acid; the advantages of a "retarded" acid are obtainable. Field testing of the acid has shown it suitable for use in sulfate-containing formations. Substantial improvements in productivity generally resulted. INTRODUCTION Acid treatments of limestones, dolomites and other formations bearing carbonate deposits are frequently unsuccessful when the calcareous formation contains sulfate, either as anhydrite (CaSO,) or gypsum (CaSO4. 2H2O). Preliminary dissolution in acid followed by redeposition of calcium sulfate appears to be a major factor contributing to poor well performance after acidizing. The precipitate is usually the gypsum form of calcium sulfate, but in higher temperature formations it may be anhydrite. The freshly precipitated crystals are nearly always very small and needle-like. They may occupy a gross volume many times that of the original anhydrite crystals and will obviously constitute an impediment to flow through newly enlarged flow channels. It is believed that the redeposition problem is most severe when anhydrite lines the fracture systems and large pores which supply the effective permeability of a formation. Microscopic inclusions of calcium sulfate also present large sulfate surface areas for dissolution in acid. In either case, great amounts of calcium sulfate may dissolve before the acid can be spent on formation carbonates. For regular spent acid (originally 15 per cent hydrochloric acid) the precipitate could be as much as 270 Ib gypsum/1000 gal acid. Two techniques have been applied by the industry for reducing sulfate plugging during acidizing. The method'.' commonly employed in the field is the attempted removal of a quantity of regular treating acid before it has reacted completely with the formation. This is practiced because the solubility of calcium sulfate is greater in a solution that is still acidic than in one which has been largely spent on the formation rock. The chance of precipitative plugging is therefore reduced if the withdrawal is successful. However, it is often impossible to get the acid out of the formation before precipitation occurs. A second possible method, which at first glance appears practical, involves addition to the acid of sequestering agents which form strong soluble complexes with calcium ions. These chemicals do increase the "solubility" of calcium sulfate in fresh acid, but to a lesser extent in spent acid. The sequestering agents have, therefore, proved unsatisfactory because the amount of sulfate eventually deposited from the spent acid may be greater than that from regular acid. Another logical approach to the problem of calcium sulfate reprecipitation is the prevention of the initial dissolution of calcium sulfate by the common ion effect. This may be accomplished by adding a soluble calcium salt to the fresh acid. The use of calcium salts in treating acids is not entirely new. An earlier suggested use of a soluble calcium salt in hydrochloric acid apparently failed to recognize the full extent to which the solubility of calcium sulfate could be suppressed. The present study extends this earlier work and adds certain improvements toward the development of a practical anti-anhydrite acid. LABORATORY DEVELOPMENT Calcium Sulfate Solubility Table 1 shows the results of a laboratory study performed to establish the effect of calcium chloride concentration on gypsum solubility. Because of the strong tendency of calcium sulfate to form supersaturated solutions, accurate solubilities are difficult to determine. These solubility data probably are reliable to within ± 15 per cent. The solubility of calcium sulfate in 15 weight per cent hydrochloric acid increases with increasing temperature. This trend is also followed in hydrochloric acid which cantains calcium chloride. This is contrary to the solubility behavior of calcium sulfate in water, wherein the solubility decreases with increasing temperature.

By Nicholas J. Grant, H. C. Chang

Microscopic observations during creep tests were made on AI-20 pet Zn, 80 pet Ni-20 pet Cr, and 25 and 3S aluminum specimens. All these materials failed in an inter-crystalline manner under certain stress and temperature conditions. Particular atten-tion was given to the initiation and propagation of intercrystalline cracks in coarsegrained AI-20 pct Zn specimens. The geometry of the grains and grain boundaries in these specimens was known before the tests. On the basis of the observations and a knowledge of the interaction between grains and grain boundaries, a mechanism of intercrystalline fracture and propagation of the fracture has been proposed. METAL, and alloy fracture occurs essentially in two ways: transcrystalline and intemrystalline. In the past most of the work done in this field was centered on the determination of stress criteria for fracture. The specimens used for these studies were tested under varying conditions of stress state, temperature, and strain rate. Unfortunately, very little attention was given to the initiation and propagation of the fracture, whereas the nature of fracture was examined closely only after failure. Several extensive reviews of these studies have been published by Orowan, Smith, Barrett, and Petch.1, 4 It is well known that a material which exhibits a ductile and transcrystalline fracture can be made to exhibit a brittle and intercrystalline fracture by modifying its composition and by heat treatment. This modification may or may not result in microscopically observable precipitation in the grain boundaries." In the creep of any one alloy the transition of transcrystalline to intercrystalline fracture is a function of stress, strain rate, and temperature." The tendency for intercrystalline fracture to occur increases as the strain rate decreases and the testing temperature increases. Extensive work on high purity aluminum (99.995 pet) under creep conditions showed the importance of the interaction between grains and grain boundaries, and the different responses of grain and grain boundaries to the variables: stress, strain rate, and temperature.7, 8 It was also shown that grain boundary deformation necessarily has to be accommodated in the grains by various deformation means as. for example, fold formation. The type of fracture resulting from the creep of high purity aluminum was invariably found to be transcrystalline. On the other hand, 2S and 3s aluminum were, under certain conditions, found to fracture in an intercrystalline manner." One reason given for this was that the grains could accommodate to a lesser extent the deformation of the grain boundaries.19 It was decided to examine this line of reasoning in greater detail and to investigate the particular interactions between grains and grain boundaries that result in the incidence and progression of inter-ct,ystalline fracture. It is also the purpose of this paper to show where and how intercrystalline cracks start and how they propagate to result in fracture. Several alloys—Al-20 pct Zn, 80 pet Ni-20 pet Cr, 2S and 3s aluminum-— were used for this study, but attention was paid mainly to the behavior of an A1-20 pet Zn alloy, since its general creep behavior has been established." From the results of this study a mechanism of intercrystalline fracture is proposed. Experimental Procedure The experimental procedure was similar to that used in previous work and has been detailed elsewhere.' Two parallel flat surfaces were milled from an originally round specimen, giving a gage portion which was 1x0.09X0.17 in. Some round specimens, 1/4 in. round by 1 in., were also tested. The A1-20 pet Zn specimens. which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar, and most of the grains occupied the whole thickness of the specimenu. Before some of the specimens were subjected to creep, the grain arrangement was mapped out in a development drawing, Fig. 1. The initiation and

Jan 1, 1957

By M. A. Dayananda, R. E. Grace

Vapor-solid diffusion couples were employed in a study of ternary diffusion in the single-phase copper-rich corner of the Cu-Zn-Mn system Interdiffusion coefficients were measured at three different compositions corresponding to the intersections of diffusion paths determined at 850°C. Intrinsic diffusion coefficients were determined at two compositions by the Philibert-Guy method. New relations between the various intrinsic diffusion coefficients are also presented. MOST of the investigations of ternary diffusion have been made with "sandwich" couples formed by welding together two homogeneous solid solutions with or without markers placed at the interface. With such couples Kirkaldy and his coworkers1,2 have determined interdiffusion coefficients which describe ternary diffusion in the substitutional alloy systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy3 have reported intrinsic diffusion coefficients for Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.4 The use of semi-infinite diffusion couples, for example, vapor-solid couples, where the diffusing species are supplied from a vapor source in contact with a diffusion disk, has so far been confined to studies of binary diffusion. Balluffi et a1.5,6 have successfully determined the interdiffusion as well as the intrinsic diffusion coefficients in several binary metallic systems employing vapor-solid couples with markers initially placed at the vapor-solid interface. They have also discussed the general advantages and limitations of such couples. Vapor-solid diffusion couples can successfully be employed in ternary diffusion studies. The importance of such couples in ternary diffusion lies in the fact that inert markers lie close to the vapor-solid interface, and the composition of the marker plane is virtually known before experimentation begins. Another minor advantage is that the method of Philibert and Guy4 may be used with three alloys instead of four. Lastly, the diffusion paths need not be S-shaped, as pointed out by Meijering7 for "sandwich" couples. The Cu-Zn-Mn system is convenient for ternary diffusion studies because of the large single-phase field in the copper-rich corner. The vapor pressure of zinc above such alloys is known, and X-ray measurements indicate that the molar volume is nearly constant over a wide range of compositions.8,9 It is the purpose of this paper a) to extend the analysis of Balluffi and seigle5 to permit an evaluation of interdiffusion coefficients in ternary vapor-solid couples, b) to use the method of Philibert and Guy to determine intrinsic diffusion coefficients with such couples, and c) to present experimental data on both interdiffusion and intrinsic diffusion coefficients for the Cu-Zn-Mn system at 850°C. INTERDIFFUSION IN TERNARY VAPOR-SOLID COUPLES The analysis of Balluffi and seigle5 is extended in this section to a vapor-solid couple where two solutes diffuse from a vapor source into a ternary solid solution. To take into account the expansion of the diffusion disk caused by the absorption of mass from the vapor phase, the total fluxes are expressed on the basis of a coordinate system that moves with the velocity of the vapor-solid interface; thus. where D3ij are the intrinsic diffusion coefficients,4 v(x, t) is the local Kirkendall velocity of mass flow, and F(t) is the negative velocity of the vapor-solid interface (x = 0). Both these velocities are based on a fixed coordinate system far removed from the diffusion zone. Using the continuity relations and Darken's method1' for a ternary system in which components 1 and 2 diffuse from the vapor phase into a solid of negligible vapor pressure, one obtains

Jan 1, 1965

By Bernard G. Carbajal

The dielectric properties and thermal stability of glow-discharge polytnerized films of styrene, chloro-benzene, and other organics and photoresist filrns are presented. Variations in the glow-discharge polymerization procedure are related to thermal stability. Thermal treatwzents to improve the dielectric properties of both positive (A2 340) and negative (KMER) photoresists are given. THIS study of the dielectric properties of thin organic polymer films is part of a program to investigate the electronic applications of organic materials. Thin organic polymer films have been produced in an ac glow discharge,13 with a low-energy electron-beam process,4 and in an rf dicharge. A process has been developed during the course of this program for forming thin organic polymer films in a dc glow discharge. These glow-discharge polymerized (GDP) films exhibit some useful dielectric and insulative properties. Variations in the properties of the GDP films can be induced by changes in the source material (monomer) andor in the conditions of the glow discharge. Thin organic polymer films can also be produced from typical positive and negative photoresists. Some variations in the properties of the photoresist films can be induced by suitable post-application treatments such as thermal crosslinking. The properties of interest in this study are dielectric constant, dielectric strength, resistivity, and thermal stability. POLYMER FILM PREPARATION I) GDP Films. The GDP films were prepared in a dc glow discharge in an atmosphere of organic monomer vapor. The details of the glow-discharge procedure have been presented previously.6 Briefly, under the influence of a dc glow discharge organic vapors can be polymerized in the vapor phase and the resultant polymer (GDP film) deposits on and in the vicinity of the cathode. Substrates placed behind a screen cathode can be uniformly coated over all exposed areas. Pattern definition can be achieved using normal mask stencil techniques. Table I presents the pertinent parameters in the preparation of GDP styrene. Conditions of Forrrzation of GDP Styrene. The rate of deposition for GDP films was monitored using a current-time integrator. The thickness of the deposited film for a given set of experimental conditions was a function of the current-time integral. The fifth row in Table I is a compilation of the deposition rate of GDP styrene films. Other organic monomers behave in a similar fashion. With the exception of the highly halogenated saturated hydrocarbons, all organics subjected to the conditions of the glow discharge form GDP films. 11) Photoresist Films. Photoresists are normally recognized to exist in two forms, a low molecular weight, soluble polymer form (A) and a high molecular weight, crosslinked insoluble form (B). Typical negative photoresists are applied in the low molecular weight form A and converted to the high molecular weight form B by the action of light. (Positive photoresists are applied in form B and converted to form A by the action of light.) Eastman Kodak Metal Etch Resist (KMER) has been chosen as a typical negative photoresist. Polymer film samples were prepared in the same configuration used for GDP films. The KMER was applied in the usual fashion using a 120°C drying step (infrared-lamp heating) and a 180°C post-bake. Care must be taken to completely remove the solvent in the drying step and to properly develop and postbake to exposed photoresist. If the photoresist film is not properly dried and postbaked, severe blistering and peeling will occur during subsequent elevated-temperature exposure. Thickness can be controlled by varying the viscosity of the form A photoresist and the spin rate at application. AZ 340 was chosen as a typical positive photore-

Jan 1, 1967

By J. E. Fox Jr., J. L. Lummus, J. P. Gallus

Fresh water or brine drilling fluids may be kept free of suspended drilled solids by the addition of a water soluble acrylamide-carboxylic acid copolymer at the flowline. Addition of from .01 to 0.2 lblbbl of the polymer solution to drilling fluids containing less than 5 per cent clay solids by weight causes the solids to flocculate and settle rapidly to the bottom of the pits. Solutions of the polymer injected at the pump suction reduce the loss of water to permeable formations without impairing the permeability to oil. The use of drill-itlg fluids clarified with the polymer has resulted in increased drilling rates, extended bit life, and lower drilling fluid costs. INTRODUCTION Field experience and the results of a number of investigations have established that the accumulation of solids in drilling fluid reduces drilling rate.'-' Drilling with water makes possible higher drilling rates than can be achieved with mud but in many areas drilling with water may not be feasible because of the possibility of encountering high formation pressures or by-dratable formations. To combat these conditions, the drilling fluid must possess certain physical properties such as viscosity, density, fluid loss, etc., which require the presence of solids. The current trend in drilling fluid treatment is to maintain as low a percentage of solids as is possible without harmfully affecting the mud properties needed for drilling. Mechanical separating devices such as wet cyclones and decanting-type centrifuges are proving to be an economical means of controlling the percentage of solids and thereby maintaining low solids muds. Also: special muds have been developed for the purpose of retarding the hydration of drilled solids so that they may be more easily removed by shale shakers or settling pits. In some areas, such as West Texas, the characteristics of some formations will permit drilling with water. However, because of the dispersion of drilled solids, it is usually not possible to maintain clear water even with the aid of mechanical separators, or by utilizing large settling pits. For this reason the commonly used term "water drilling" is a misnomer since the water usually contains some solids. Because of the improved drilling rates and other benefits which might be effected, a laboratory and field study was made of the use of flocculating agents for maintaining clear water for drilling. PROCEDURE Laboratory—Solids Settling Two techniques were employed to determine the effectiveness of flocculating agents in settling solids from drilling mud. First, the rate of fall of solids was measured in graduated beakers containing mud treated with various flocculating agents. Natural gum, oil-in-water emulsions prepared with ethoxylated nonyl phenols and diesel oil. and a powdered synthetic acrylamide-carboxylic acid copolymer* (hereinafter referred to as "polymer") were tested as flocculating agents in both fresh water and salt saturated muds containing 4 per cent solids. The polymer was not added in the powder form directly to the muds but was first dissolved in water in a concentration of 3.5 lb/bbl. The polymer solution was then added directly to the mud. The concentration of the flocculating agents, including the polymer, was varied. High rates of fall of the solids indicated high flocculating efficiency. A second technique consisted of measuring the time in minutes required to obtain clear water at the pump suction after addition of the various flocculating agents at the flowline. These tests were made using a model mud circulating system having a total volume of approximately 10 gal. The natural fresh water and brine muds used contained 4 per cent solids. A sketch of the circulating system appears in Fig. 1. The circulating rate

By J. M. W. Mackenzie

The interactions between oil drops and mineral surfaces have been examined for the cetyltrimethylammonium bromide (CTAB)-quartz and sodium dodecyl sulfate (SDS)-hematite systems. The results have been interpreted using a electrical double layer interaction model, a "sweeping-penetration" model based on steric interactions and a free energy of adhesion model. The adsorption of long-chain ions at the mineral interface was also studied and found to follow a Fuerstenau-Modi model of combined Coulombic and chain-chain interaction forces. The basis of the emulsion flotation process and the feature which makes it differ from conventional flotation is: encounter, followed by adhesion, between oil drops and mineral particles which are suspended in an aqueous environment. The manner in which the adhesion between these two phases contributes to the flotation process may be through the formation of min-eral-oil drop-mineral linkages, mineral-oil drop-air bubble linkages, or a combination of both. Possible flotation mechanisms derived from these adhesion processes are shown schematically in Fig. 2 while Fig. 1 shows an example of the first mechanism for quartz particles which have been floated using a cetyltrimethyl-ammonium bromide (CTAB)-Nujol emulsion as collector. In Fig. 2 the three phases, mineral, oil, and air, for convenience have been shown as having approximately equal size. This would not always be the case in an actual emulsion flotation operation. For the flotation of sand-sized particles of approximately 0.5 mm diam, the mineral particles would be at least ten times the size of the largest emulsion drops present in the system, while in the flotation of —10u slime particles, the mineral phase may be of the same order of size as the oil phase. The air bubbles in a flotation cell are normally about 1 to 2 mm in diam and therefore, in general, would be larger than the oil drops. Although the relative size of the three phases does not alter the basic adhesion processes between oil drops, mineral particles, and air bubbles, which depend on the physical and chemical properties of the interfaces involved rather than on the extent of these interfaces, it does alter the degree of deformation of the oil drops and air bubbles which will occur on adhesion. For mechanisms 1 and 2 to take place, the oil-water and mineral-water interfaces must be partially replaced by a mineral-oil interface while in mechanism 2 there is the additional requirement that the oil-water and air-water interfaces must be replaced by an oil-air interface. In view of the importance of the oil drop-mineral particle encounter and subsequent adhesion stages to both of the emulsion flotation mechanisms discussed, a study has been made of some physicochemical factors which control these processes for Nujol-cetytri-methylammonium bromide (CTAB)-quartz and Nujol-sodium dodecyl sulfate (SDS) -hematite systems. Experimental Electrokinetic Measurements.—The zeta potential of mineral particles was measured using a streaming potential technique similar to that described by Fuerste-nau.1 The streaming potential was measured using a multirange electrometer while the plug conductivity was measured using a 50 cycle sec1 bridge. Measurements were made on 28 x 65 mesh particles. Contact Angle Measurements.—A captive bubble technique was used to measure the contact angles for air bubbles and oil drops. The angles were measured on fracture faces of unmounted minerals which proved easier to clean than polished mounted specimens and should more closely represent a flotation system. Reagents: These have been described in a previous publication.0 Minerals: Rock crystal quartz from the New England district, N.S.W., was used for contact angle and streaming potential measurements. The quartz was hand

Jan 1, 1971

The program for the Annual Meeting to be held in New York, Feb.17 to 20, 1919, inclusive, has been nearly completed. Besides the usual meetings for the reading of technical papers, the social features are being given special attention. They will probably embody the following: On Monday evening, a lecture by one of our fighting airplane pilots, to be illustrated by lantern slides and moving pictures. To this entertainment the ladies will be invited, as well as members. On Tuesday evening, a Smoker at which some very startling features are promised for the entertainment of members. On Wednesday evening, the usual banquet, at which it is hoped to have some very interesting speakers. The usual luncheons will be served in the Engineering Building and other features will be offered for the entertainment of the ladies during the day. No definite plans for the Thursday excursion have yet been formulated, though it is probable that something interesting will be offered the members.

Jan 12, 1918