Search Documents

By C. A. Heiland

MEASUREMENTS of gravity with gravimeters have come into increased use in this country and abroad in the past five years. Probably 100 to 125 gravimeter parties are working in the United States alone. In oil exploration, gravimeter methods have relegated the gravity pendulum definitely to second place, if not third, and now closely rival and possibly surpass the torsion balance in many applications. Gravimeters have lately been applied in mining, although it is doubtful whether they will ever replace electrical or magnetic methods in this work. Notwithstanding the widespread application of gravimeters, there has been no article covering the entire field in the domestic or foreign literature. The purpose of this paper is to meet the demand for com-prehensive engineering information on the subject. The working principles of a number of gravimeters will be, illustrated and treated in relation to the action of corresponding seismometers and astatization methods. The mathematical discussion of theory has been confined to the most necessary fundamentals and been given in as ele-mentary form as possible. A description of calibration methods con-stitutes the last part of the paper. The symbols shown at the top of page 2 will be used in equations throughout the paper.

Jan 1, 1939

By J. Mazia, H. Rosenthal

An investigation has been made of residual stress in the head and body of caliber 0.30 cartridge cases. The head was divided into four ring-lie sections which were cut off by a jeweler's saw. Spring-out was measured after a radial cut had relieved the circumferential bending moment. The residual stress corresponding to the observed spring-out was calculated by formulas in which the computed stress was a function of wall thickness. All rings sprang open, indicating compressive stress on the inner wall and tensile stress on the outer wall. The production stress-relief anneal of 475 F. for 45 min. reduced the stress to almost half. The priming and crimping operation, however, again raised the stress, especially in the flange section. The dect of stress-relief heat treatments on residual stresses in the body of caliber 0.30 cartridge cases was investigated by the split-ring method. Although this method did not reveal any large stresses in the body, the neck before mouth anneal was found to contain a computed stress of 30,000 psi. at the surface. This value was reduced to 15,000 psi. in 120, 30, and 15 min. at 400, 475, and 500 F., respectively.

Jan 1, 1945

By L. A. Panek

Using an approach based on the theory of similitude, the author develops a general equation and related concepts that provide new insights to an old problem. The load-bearing capacity (strength) of a square, rectangular, or cylindrical prism of a brittle material such as rock, coal, or concrete is expressed as the mathematical product of a size effect, a shape effect, and a function of the mechanical properties (deformability, cleat/joint spacing, and friction) of the pillar, roof, and floor materials. Through an application of multivariate statistical analysis, the results of assorted tests (laboratory and in situ) and observations of failed pillars can be combined into a fundamental scaling equation, which provides a unified, consistent approach to the estimation of mine pillar strength. The form of the equation is sufficiently general to be able to incorporate refinements in the characterization of the structural parameters, as they become available through future analysis and experimentation. Analysis of the published test data suggests that pillar compressive strength (per unit of area) is proportional to the cube root of the pillar width, and that the height effect can be described as the superimposing of a variable size effect (characteristic of the material) on the constant width effect.

Jan 1, 1981

By Alan F. Stewart, Douglas R. Piteau, Dennis C. Martin

Three examples of open pits where toppling failure controls the stability and design of the slopes are described. Two examples involve the design of overall slopes in base metal mines. The third example concerns the analysis and design of remedial measures to prevent toppling failure from occurring in a critical slope in a coal mine. The analytical techniques for assessing toppling failure on a rational basis are discussed for the three examples. This includes an assessment of the important parameters which govern the stability for the toppling failure mode. The geological setting and input data for each example are described, as are the important external or limiting factors pertinent to the sites in question. A statistical cumulative technique was used to assess one of the most important input parameters in the two examples involving overall slope design. Both deep-seated toppling failures, involving the entire slope, and shallow bench failures are considered. Results of the stability analyses and their related engineering significance with regard to slope stability and design are discussed. A sensitivity analysis of various parameters is effectively utilized. Design charts are developed and evaluated accordingly. In the example where toppling failure was unavoidable, the rationale for design of stabilization techniques to prevent toppling is discussed.

Jan 1, 1983

By F. Keller, E. H. Dix, R. W. Graham

Aluminum alloys containing relatively small amounts of magnesium and silicon are of commercial interest because they are readily workable in the annealed form and may be hardened and strengthened by suitable heat treatment. An intermediate temper can be produced in these alloys by quenching after a Solution heat treatment and the alloy in this condition can be formed easily. Artificial aging is required to obtain the maximum mechanical properties but this aging does not cause distortion nor require elaborate heat-treating equipment. The hardening of the alloys after quenching is attributable in part to the retention of the compound Mg²Si in solid solution, while the maximum hardness obtained by subsequent artificial aging is attributed to the fact that the solid solubility of the compound Mg²Si in aluminum decreases with decreasing temperature. Considering the importance of aluminum alloys susceptible to heat treatment, it is surprising how few fundamental investigations have been carried out on the aluminum-magnesium silicide alloys. This paper deals principally with the solid solubility relations of the compound Mg2Si in aluminum and is the sixth paper of a series1 from the laboratories of the Aluminum Co. of America reporting the results of investigations of equilibrium relations in aluminum-base alloys made from high-purity aluminum."

Jan 1, 1931

By Hugh O?Neill

IN PREVIOUS papers,1 the author has reported the results of experiments on the straining in tension of a single crystal test piece, about 0.6 in. long, of vacuum-melted electrolytic iron containing 1.8 per cent. of silicon. The crystal was originally in the "as cast" condition, and was stressed slowly along a tetragonal axis so that slipping along conjugate gliding planes finally transformed the original cylindrical portion into a pair of fracture wedges. One of these fracture wedges was sectioned along the stress axis in a plane at right angles to the edge of the wedge. A metallographic study of this plane of -section led to the conclusion that slip had taken place in the (111) direction along (112) planes making a V shape with the stress axis. The present paper describes the results of scratch-hardness tests conducted on the same section, in order to determine the distribution of strain hardness therein, followed by annealing, and considers the resulting variations in hardness. These observations supplement those made by Krivobok2 on similar material reduced 25 per cent. by hammering (i. e., by impact) in the cold. In order to investigate ageing effects, two small crystals of the same alloy were also tested.

Jan 1, 1928

By Kenneth S. Ritchie

The natural emulsion samples used in this study were shipped directly from twelve California oil fields, through the courtesy of the superintendents of the main producing companies in those fields. Representative parts of each sample were chosen for the slides. Preparation of the slides was generally made in less than two minutes, including time of exposure; in a few cases, about five minutes was required. The short time was intended to minirmize the changes in conditions. Whenever comparison was of value, standard conditions were established. Spreading by gravity was adopted instead of smearing. Cover glasses were not allowed to rest on the films. General Characteristics of Emulsions The main purpose of the general views (Figs. 1-16) is to illustrate the general characteristics of the dispersed droplets together with any other constituent or impurity that may be found in each emulsion. The magnification is given so that dimensions could be measured from the plates. The slides used for these views had spherical recesses; they gave the best light. Where crystals were intended to be shown in the picture a filter (green was the best') was usually used. Emulsions that showed a tendency to move by concentrated light were pictured without a condenser.

Jan 1, 1931

The term "timbered stope" is here meant to denote stopes in which timbering is the predominant feature of the mining method. Stopes with stull sets, as in the Hecla mine, are types of timbered stopes; these types are probably the best-known. Timbering stopes by means of square sets is not as common as formerly, as the system is not often necessary, yet there are good examples and large tonnages are being mined by the method. The square set may be utilized in ordinary overhand stopes if the orebody is suitable. At some mines, square sets have been abandoned in favor of top-slicing; and at others, the square set has superseded horizontal cut and backfilling. A drift, either in the wall or orebody, is necessary before opening the sill floor. In wide deposits, there may be a grillage of drifts and crosscuts, and at least one raise to the level above is needed in each stope for ventilation and handling timbers and filling. The square sets are filled with waste rock from the hanging wall, sorted from the ore, from development work, or from the level above. As a rule, little timber is recovered. The examples include the Butte district, Mother Lode of California, Bunker Hill & Sullivan, Hecla, and Morning mines.

Jan 1, 1925

By Malcolm T. Hepworth

RECENT interest in thermoelectric devices has been directed toward studies of the properties of thermoelectric materials of semiconducting solid compounds with little attention given to ionic and semiconducting liquids such as aqueous solutions, fused salts, and mattes. One type of thermoelectric system is the thermocell: a nonisothermal galvanic cell with two identical electrodes at different temperatures connected by an electrolyte bridge. An electromotive force, v, is generated which is a function of the electrode reactions and the properties of the electrolyte according to the Eastman' equation: where S* is the entropy change of the system arising from the electrode reactions and by heat transferred by ion migration and by thermal conduction. The quantity nF is the product of equivalents passed and Faraday's constant. A value of S* of 23.06 cal per "C is equivalent to 1 mv-Faraday per "C. The symbol, a, is used for dV/dT in analog to the See-beck coefficient of solid-state thermoelements. de Bethune2 has calculated the temperature coefficients of the electromotive force of a large number of nonisothermal aqueous cells from measurements on the nonisothermal temperature coefficients of the standard hydrogen electrode, combined with data on the isothermal temperature coefficients of half-cells tabulated in the literature. Values of these coefficients (a) in de Bethune's compilation ranged up to 3 mv per C. In particular he reported a value of +2.059 mv per "C at 25'C for the cell: Fe (aqueous, unit activity) (aqueous, unit activity) written for the hot-electrode reaction. The positive sign indicates that the hot electrode is positive (an "n-type thermocell"). In analog to a solid-state p-n system, it would be possible to couple two thermocells together to form a system in which the figure of merit could be calculated by adding the temperature coefficients according to the relationship described by offee:' where a is the Seebeck coefficient in volts per "C, p is the specific resistivity in ohm-cm, and K is the thermal conductivity in watts per cm "C. Even though ionic systems have rather high electrical resistivities compared with semiconducting and metallic systems, it was felt that a preliminary study of one ionic system should be made to establish some basis for evaluating the possibility of a p-n thermocell for energy conversion. Accordingly the Fe", Fe"' system was studied as a possible component for a p-n system. A glass system was constructed consisting of two vertical water-jacketed tubes connected by a horizontal tube, Fig. 1. Platinum-black electrodes 1 cm by 1 cm in dimension were inserted in each vertical tube with thermometers to register the electrode-compartment temperatures. The temperature of the electrode compartments was controlled by circulating water from thermostatted baths around the electrode compartments. The electromotive force of the cell was then read by a potentiometer for zero current as a function of the temperature of the hotter electrode. Current output of the cell for varying external loads was also measured. The cell resistance was measured by means of a bridge circuit with 10,000 cps signal and oscilloscope. Resistance measurements were converted to specific resistivity by calibrating the cell with a solution of known conductivity.

Jan 1, 1965

Senator Smoot recently introduced his bill providing for the leasing of oil and coal lands. This bill provides only for the leasing of these lands from the Government and advocates government ownership of all government coal and oil lands. Under the provision of the bill as now proposed, 50 per cent. of all money received under the measure is to be paid to the state in which the land is located. The money must be used, however, for the construction and maintenance of roads and for schools. The last leasing bill was defeated when it was about to become law largely because of the fact that it allowed the sale of coal lands.

Jan 9, 1919

By M. R. Moharam

The well-known formulae of screening efficiency and circulating load calculations in closed crushing circuits were exploited to achieve graphical estimation of these parameters. Three basic charts were proposed and constructed. The first one is for the regular closed circuits where the new feed goes to the crusher. The second is for the reverse closed circuits in which the new feed reported to the screen is free of screen undersize particles. The third chart controls the reverse circuits when they are receiving new incoming feeds containing undersize material. Compound circuits were also reanalyzed and a concept of equivalent simple circuit was introduced to enable graphical manipulation of these complex circuits with the help of the aforementioned charts

Jan 1, 1982

The Board of Directors on April 18, 1940, adopted a resolution providing that "no person who has been awarded any one of the four medals-Douglas, Saunders, Lucas, and Rand-is eligible for consideration for any other of the four medals " Later in the year the rules for the award of these four medals were revised and, so far as practicable, made uniform The medalists are elected by the Board of Directors, on recommendation of special standing committees of award, appointees on which serve four-year terms and are engaged in the branch of industry represented by the respective awards Under the rules only members of the committees of award are eligible to propose candidates\ for the nomination

Jan 1, 1952

By H. R. Hardy

The study of the mechanical properties of geologic materials was initiated in the Mining Research Section of the Fuels and Mining Practice Division in 1951 as part of a fundamental study of ground stress in Canadian coal mines.1 Early in the investigation of the mechanical properties of geologic materials, however, it was realized that the test results are influenced by the rate and the duration of loading. For this reason, laboratory investigations2,3 were undertaken to study the effect of long-period uniaxial stress on the deformation and failure properties of these materials. A literature survey indicated that work on the time-dependent properties of geologic materials had been very limited in the past.

Jan 1, 1965

By D. B. Grove

THE heavy media separation process plays an outstanding role in the concentration of 4000 tons of zinc ore per day at the Mascot mill of the American Zinc Co. of Tennessee. Of the total tonnage, 72 pct is treated in the heavy media separation plant to reject 56 pct of the ore as a coarse tailing, which has a ready market. Concentrates from this separation are beneficiated further by jigging and flotation. Approximately 25 pct of the total zinc concentrate production is made in the jig mill. Jig tailings are ground and pumped to the flotation circuit where the balance of the production is made. Fig. 1 shows a generalized flowsheet of the mill.

Jan 8, 1951

By Milton E. Jennings

On May 11, 1977, the SAMARCO 508-mm (20-in.), 396-km pipeline was placed in service. This system represents the latest thinking in slurry pipeline design and is one of the main contributors to the viability of the SAMARCO project. This paper presents the background, description, and latest information on the system's operation. Special attention is given to the handling limitations of the slurry and to the unique hardware requirements.

Jan 1, 1982

By AIME

Burton J. Westman-Besides decreasing the diamond size, there appear to be two other approaches open to overcome excessive diamond loss and, more particularly, the rapid diamond polish that took place in this quartz-feldspar rock. First, however, a short discussion of the diamond characteristics should be made in order to discuss the situation more clearly. The West African diamonds which we can assume were used. for this drilling have two disadvantages when drilling hard, exceptionally fine-grained rocks. These are rapid polishing and, if .the bit isn't "drilled in" carefully, a tendency to damage, resulting in excessive diamond loss. The normal wear resistance of any diamond is inversely proportional to the compressive strength of the diamond, therefore only the highest grade, of diamonds free from insipient fractures should be employed. Using upwards of 90 diamonds per carat instead of the20 to 30 per carat not only decreases the total projected area of the cutting points but increases the stress per point which, in turn, causes greater depth of penetration into the rock. Considering this depth of penetration, therefore, suggests an approach other than increasing the, number of diamonds per carat and that is to decrease the actual number of diamond points (also the carat weight per bit) so that the penetrating force on an individual diamond is increased. This penetration increases the chipping or rock shearing action.

Jan 1, 1950

By E. H., Edwerd H. Robie

WILLIAM CHURCH was one of the founders and the first president of the Detroit Copper Mining Co. and was the first man to interest the Phelps Dodge company in the possibilities of the Morenci district, in the '70's. One rather interesting story concerning him is told by James Colquhoun, at one time president of the Arizona Copper Co., in his "History of the Clifton-Morenci Mining District." It seems that a geologist visited the Detroit company's mines and gave Alec McLean, then mine superintendent, quite a lesson on the proper mineralogical terms for what he saw in passing. Later, McLean handed out a few of them to Mr. Church as they walked through the mine on a tour of inspection. The latter had even less regard for a geologist than he did for sulphide ore, which meant little indeed, for in those days the rich ore was all oxidized, and there was no money in the sulphides. So Church was completely unimpressed by the geological and mineralogical terms that McLean had acquired from the visiting geologist. Church turned on him and warned him that so long as he was a member of his staff he was to understand that there were only two kinds of rock in his mines-the one was smelting ore and the other was waste rock, and he was not to forget it.

Jan 1, 1942

By Sherwin F. Kelly

THE joint meetings of the Mining Geology Committee and the Society of Economic Geologists proved to be deservedly popular, and the interesting papers drew an attendance which strained the capacity of one of the large meeting rooms.. As might be expected these days when even the Supreme Court can't keep away from the subject of gold, the discussions opened on Thursday morning with several papers devoted to questions of structural and mineralogical relationships of the deposits of this metal. The presentation of Ira B. Joralemon's paper, "Veins and Faults in the Bralorne Mine," by Reno Sales, elicited considerable discussion on the relation of mariposite to gold, and the situation of the gold deposits with respect -to the Coast Range batholith. H. V. Warren stated that lie had observed mariposite always to be associated with gold in this region, but that gold was not always associated with mariposite. He pointed out that there is a series of veins on the west side of the batholith with a different mineralogy that, because of their richness but small size could quite easily make good, small mines. John A. Dresser concurred in this, and said lie thought this region was one of great promise for the mining geologist. He also reported having found mariposite associated with gold values below commercial limits, in the Appalachian regions.

Jan 1, 1935

By William Kelly

I AM-glad to have the opportunity at this time to say that I consider it a very great honor to be elected President of the American Institute of Mining and Metallurgical Engineers. It fulfills the proudest hopes of my ambition. There is, ,however, one drawback to my personal gratification-a feeling of unworthiness to have my name placed on the list with former Presidents of the Institute, with the brilliant Raymond who guided our society for so many years, with the versatile and lovable James Douglas, my first employer and my friend, a most generous benefactor of our Institute, with the skilful Holley, who gave to the manufacture of steel in this country, its first great impulse, to mention only three of the accomplished men who have preceded me. I assume that the honor of my being elected President of the Institute is not merely a personal one but that it should be considered a tribute to the wonderful progress in the art of mining, both underground and in open pits, and in the beneficiation of native copper and iron ores, which have been shown in the Lake Superior District and also a recognition of our members there and elsewhere who are living at the mines and directing the operations, upon the success of which the whole mineral industry depends.

Jan 1, 1924

By William B. Plank

ENGINEERING students to the number of 73,269 had been enrolled in United States and Canadian schools on Nov. 5, 1945, but, as shown in the following tables, even this sizable number will not greatly remedy the 150,000 deficit reported by Vannevar Bush, director of the U. S. Office of Scientific Research and Development, to exist in the engineering and scientific man-power supply. These figures were received in advance from the Society for the Promotion of Engineering Education, and are given in detail in the January 1946 issue of the Journal of Engineering Education. Although the enrollment on Nov. 5 was an increase of 76% over the low of 41,632 in 1944-45, it was still 36% below the peak enrollment in 1941-42 of 115, 228. These figures include both undergraduate students and graduate students in the schools of the United States and Canada and are therefore comparable. As was to be expected, almost half of this enrollment is in the first or freshman year and 25% of the total are veterans. Also, 1,850, or about 2.5%, are women. A measure of the seriousness of the engineering graduate supply in these two countries is indicated by the trend of the number of first degrees that have been conferred during this period of scarcity:

Jan 1, 1946