Search Documents

By Richard Thomas Newcomb

Chapters 5a, 5b, and 6 discuss the long- run supply of minerals and the characteristics of reserve search and production peculiar to extractive industries. It is now necessary to complete the picture by examining supply and demand in commodity markets to show how mineral prices are determined and how both price and production trends might be predicted over long periods of time. These practical interests can be served best by reviewing first some of the characteristics of the short-run static market models familiar to all readers of elementary economic texts, and then extending the theory to models of a more dynamic nature. It is important at the outset to note that economic theory provides a wide variety of economic models based on varying assumptions concerning the behavior of economic agents, the properties of the goods, the time period considered, and so on. Each variety of model offers certain analytical advantages and suffers certain shortcomings. The art of the applied economist or practioner lies in knowing enough both about the technology and practice of his problem and about theory to select the appropriate models for his analysis. In our approach it will be useful first to consider the role of markets for minerals and mineral products in relation to the efficient determination of what and how goods are produced in the whole economy, i.e., a general system of markets, before getting down to the task of analyzing supply and demand conditions in specific markets. The former study is called general equilibrium analysis, while the latter is called partial. By equilibrium is meant a state of the sys- tem under study in which supply equals demand in each market, and the prices which equilibrate the quantities offered and asked are called equilibrium prices. The tendency of prices to return toward equilibrium values if temporarily displaced, or to converge to new equilibrium values if important new conditions for supply or for demand are placed, defines "stable" equilibrium systems. The short-run describes a period in which adjustments to fixed capital are not made, although variable factors such as labor or materials can be adjusted. The long-run envisions a period in which fixed capital and other such constraints can be adjusted. Thus, it may take a sharp increase in price to bring out additional supply of a factor in the short-run with existing plant, while new capacity might permit additional quantities in the long-run without an increase in supply price.

Jan 1, 1976

By R. F. Mehl, C. S. Barrett, A. G. Guy

INTRODUCTION IN the last few years this laboratory has published a series of papers on the mecha¬nism of age -hardening.14,1,6,11,20 Briefly stated it has been proposed that hardening is caused by lattice strains created by lat¬tice coherency between matrix and precipi¬tate; much experimental evidence has been advanced to support this thesis. The system Cu-Be is an attractive one to study. It is a system that exhibits marked age hardening; it ought to be subject to the type of analysis of structural changes hitherto explored and it is a prominent example of "discontinuous precipitation," which, though studied in other cases, 6,20 remains largely unexplained. This research shows that hardening in the Cu-Be system proceeds essentially as proposed earlier.14 Guinier-Preston zones have been observed to form on the {100) planes of the matrix; no transition lattice was found. Aging and overaging were ob¬served to occur most rapidly in the region of discontinuous precipitation-the grain boundary-apparently accelerated there by strain. The Constitution of the Cu-Be System The Cu-Be constitution diagram is shown in Fig I. The structure of the ? phase was determined by Misch16 as of the caesium-chloride type with a lattice con¬stant of 2.598 Å High temperature X ray photograms of 7.2 pct Be alloy made by Kossolapow and Trapesnikow13 led them to conclude that the structure of the P phase is simply disordered body-centered cubic with [ao] = 2.79 Å at 750°C. Previous Work The initial work on the age-hardening of Cu-Be alloys was that of Masing, Dahl, Holm, and Haase. Their numerous papers were published in book form in 1929, sub¬sequently translated.18 The effects of Be content, solution temperature, aging tem¬perature, and cold work on the hardness developed in these alloys were studied. An initial decrease in the electrical conduc¬tivity was observed when strips of a 2.5 pct Be alloy were aged at temperatures from 200 to 350°C; a wire of the same analysis failed to exhibit this decrease when aged at 350°C. A volume decrease of 0.6 pct oc¬curred during aging at 250°C. Microscopic investigations of quenched and aged alloys disclosed a regularly ori¬ented "striping" (ripples) on the a and on the ß grains. In the case of the ß the cause of the striping was held to be decomposition

Jan 1, 1948

By J. Chipman, H. R. Larson

The data previously reported for the quantity as a function of oxygen pressure at 1550°C have been used to compute the activities of Fe, FeO, Fe2O3, and COO in slags of the ternary system. Activities of the first three have been obtained also for two quasi-ternaries involving fixed CaO:SiO2 ratios. IN a previous paper1' the authors reported the results of an investigation into the effects of oxygen pressure on the composition of various simple slags analogous to some of those which are found in steel-making practice. The ratio of ferric iron to total iron was studied at 1550°C in iron oxide melts to which lime, magnesia, lime-plus-silica, and other oxides were added. The oxygen pressures involved those of air, carbon dioxide, and carbon dioxide plus carbon monoxide in several proportions. Although very low oxygen pressures could not be used, the slag-metal equilibrium studies of Fetters and Chip-man' permitted extending the results to slags in equilibrium with iron. For the ternary system CaO-FeO-Fe,O, the oxygen pressure-composition relationship has been determined from zero percent lime to lime saturation over an oxygen pressure range from air to that represented by equilibrium with liquid iron. Lime and silica were added to iron oxide in the ratios 0.54, 1.306, and 2.235 to form three quasi-ternary systems which were also studied over the entire region of liquid melts at 1550°C. Ternary Gibbs-Duhem Equation Wagner" has developed a method by which the activities of two components of a ternary system can be calculated if' the activity of the third component is known throughout the composition range being considered. The fundamental form of the Gibbs-Duhem equation for ternary systems is N, d In a, + N2 d In a, + N3 d In a3 — 0. Wagner has developed a usable form of this equation by introducing the term y = N3/(N3 + N1) and rearranging the equation to give (? In a1/?N2)x = -y/(1-N2)2 (? In a2/?y) x2 N2/1-N2 (? In a2/?N2) y To apply this equation to the slag system CaO-FeO-Fe,O,, the activity of one of these components must be known. However, the only activity which is known from the experimental data is the activity or pressure of oxygen in the gas phase with which the slag is in equilibrium. The activity of oxygen in the slag can be defined as the square root of the oxygen pressure. In order to use oxygen as one component, the composition of the slags must be converted to the basis Fe-O-CaO. Oxygen, exclu-sive of that contained in CaO, then becomes com-ponent 2 in Eq. 1, Fe is selected as 1 and CaO as 3. Then y = Ncao/(Ncao + NFe). Eq. 1 then becomes (? In a fe/? Nx) y = -y/(1-No)2 (? In ao/?y) xp - No/ 1- No (? In ao/ O No) y. In order to evaluate Eq. 2, the boundary conditions must be known. The obvious choice of a standard state for iron is to assign slags in equilibrium with iron an activity of one. Then In a,., or log aFe, which is substituted for convenience, is determined by integrating along a line of constant y from the slag in equilibrium with iron to the composition at which log a,, is to be determined. Mathematically this can be expressed as log aFe (Nlog y) = log a'Fe + (? log a Fe/? No) dNo where the primes indicate equilibrium with liquid iron and a'Fe = 1. When Eq. 3 is integrated along a line of constant y, the following is obtained: log a Fe (No, y) = - y No ?/ No ? y ( log ao/(1- No)2) No d No - No/1-No d log ao. Lime-Iron Oxide Slags Iron Activity: The oxygen pressure of lime-iron oxide slags is shown in Fig. 1 as a function of j, de-fined as j = Fe+++/(Fe++ + Fe +++) for various constant mol percentages of lime. The j values at 0 to 60 pct lime were then determined for oxygen pressures of 1, 10-1, etc. to 10-" atm. For purposes of calculation, the line for zero percent lime was extrapolated to

Jan 1, 1955

By David R. Mitchell, R. M. Fleming

MANY trends were evident in the coal industry during 1951. Some were favorable for the industry; others were not. Probably those having the most far-reaching consequences are those affecting coal's markets. The rapid dieselization of many railroads and the continued trend toward oil and natural gas for home heating has caused serious dislocations in various mining districts. Mines have been forced to close down or to work on a reduced time basis. Conversely the increased activity in the metallurgical industries has increased the demand for coking and special purpose coals, and the growing production of electric energy has increased the demand in certain areas for steam coals. The increased demand for metallurgical coal and for steam raising by the large utilities is more than equal tonnage-wise to the loss of coal to railroad dieselization and conversions to oil and gas in the domestic market. Since much of the expansion is at captive mines of large corporations, many commercial operators supplying railroad and domestic users have had their markets curtailed without any compensating demand from other sources. Feverish activity was in evidence in many areas by commercial operators attempting to find new markets. The Norfolk and Western Railway is the, only major American railroad committed to the burning of coal. It has an exceptionally good cost record. During 1951, fifteen additional modern coal-burning steam switching locomotives were authorized for construction in the company's Roanoke shops at a cost of about $1,450,000. When the new order is completed the road will own a total of sixty locomotives of the modern-switcher type, including thirty acquired by purchase last year. The Norfolk and Western today is the only American railroad building its own motive power. All of these locomotives burn coal. Production Coal production in the year 1951 will approximate 570 million tons of anthracite, bituminous coal, and lignite. Of this, approximately 7 pet is anthracite. Total production is approximately 30 million tons more than in 1950 and reflects the increase in general industrial activity. Exports are expected to be close to 50 million tons. The industrial stockpile is close to 75 million tons, the highest it has been since 1943. With the exception of the usual local stoppages the year 1951 was unmarked by labor disputes. It was a year of good labor-management relations with a negotiated wage increase unmarred by a work stoppage. This may be the beginning. of an era of sensible negotiations to find agreeable settlements of disputes without the usual protracted bickering and industry-wide strike. The United Mine Workers of America has condemned wildcat strikes, stating that in nearly every, instance proper grievance procedures have not been instituted. Government defense organizations, perhaps profiting by their experiences during World War II, are pursuing a more enlightened program with regard to the fuel requirements of the nation. Many prominent officials have stated that wherever possible coal should be considered the primary source of fuel in all defense expansion. With the increased consumption of steel by defense projects, approval of transportation facilities for liquid and gaseous fuels have been refused where these fuels would enter a coal producing area. Liquid and gaseous fuel producers also have failed to provide satisfactory evidence that they have sufficient reserves and are capable of supplying their product in adequate amounts for the periods of time required. Realization has at last become prevalent that the hydro-electric power installations in several areas are insufficient to handle increased demands.' Steam generating plants are being constructed in these areas and equipped to burn coal. Most notable of these, is the TWA area whose supplemental steam power plants are expected to consume 10 million tons of coal per year when completed. The Pacific Northwest is another area which is expected to follow the same pattern. Nearly all new steam-power generating plants are being equipped to burn coal either as a primary fuel or as an emergency measure. Metallurgical Coal The steel and other metallurgical industries are expanding rapidly to meet increased industrial demands and defense orders. Since these industries are dependent on coke, coke has had a year of high production and can be expected to break all existing records when steel-plant expansions are completed. Most notable of the expansion projects is that of the Delaware River area where the iron ore will be received by ship from Canada and South America. U. S. Steel is only one of several steel corporations that are planning on putting integrated steel producing units in this area. The Defense Solids Fuels Administration announced in December that through. November 30, 1951. 29 projects in eight states, with a total cost of

Jan 1, 1952

By N. S. Stoloff, K. R. Jordan

The temperatwe and grain size dependence of the mechanical avoperties of ordered and disordered Fe-49 pct Co-2 Pct V were investigated. The yield and flow stresses obeyed the Hall-Petch relationship u = ai + kd-&apos;I2. Ohdering reduced the intercept stress cjj and raised the Petch slope, k, at all temperatures. Ordering also increased the temperatwe dependence of k. The ductile to brittle transition temperature increased with order and grair~ size. Cleavage fracture was nucleation limited and the fracture stress did not zlary linearly with d-&apos;". A quantitative test of the Cottrell-Petch fracture theory (and recent modifications which consider the influence of slip mode), demonstvated that this theory is not applicable to FeCo-V. COTTRELL&apos; and etch&apos; independently suggested that a criterion for cleavage failure at the yield point, a,, based on dislocation pileups at a grain boundary or other obstacle to dislocat.ion motion, is: aYYkd&apos;I2 1 opy [ll or, equivalently, aikz,d112 +k:)bpy [2] where a, and ky are the Hall-Petch intercept and slope, respectively, 2d is the grain diameter, P is a geometric factor dependent on the macroscopic ratio between shear and tensile stress, p is the shear modulus, and y is the true elastic surface energy. When the product of quantities on the left side of the equation is equal to or exceeds that on the right, cracks should be able to nucleate and propagate at the yield stress, as shown schematically in Fig. 1. Therefore a high intercept stress, high Petch slope, or coarse grain size favors brittleness. petch3 associated the existence of a ductile to brittle transition in ferrous alloys with the temperature dependence of ai. One of the earliest modifications of the Cottrell-Petch theory was presented by ~rmstrong,~ who derived an expression for transition temperature in terms of several measurable flow and fracture parameters. The latter paper was able to rationalize situations in which the transition temperature increases with decl-easing grain size, as in the case of molybdenum,&apos; and also suggested that Ppy should be a function of grain size as well as temperature. More recently Johnston et a1.6 and Smith and worthington7 have suggested that the temperature or composition dependence ol&apos; ky must also be taken into account if there is any cha.nge in deformation mode, as from wavy to planar slip, or wavy slip to twinning, with change in temperature or solute content. Armstrong %as suggested that for hcp metals changes in o;k,dw> o;k,d1/2< / is / ^^^^ / / y_______________________________________ d-"2 Fig. l—Schematic representation of grain size dependence of yield stress, cry, and fracture stress, CTF. Intersection defined by Cottrell-Petch equation. slip mode should be incorporated in the theory through changes in the critical resolved shear stress for the slip system which controls ky. The purpose of the present investigation was to critically test the modified677 Cottrell-Petch theory of fracture in the superlattice alloy Fe-49 pct Co-2 pct V, by studying the grain size dependence of the yield and fracture stresses over a range of temperatures, in conjunction with an investigation of slip mode and fracture behavior. Previous work has shown that long range order results in a sharp decrease in flow stress, a small increase in work hardening rate and a drastic upward shift in the ductile-brittle transition temperature of F~CO-V.~&apos;~ The only comprehensive study of slip character in this alloy has been reported in a preliminary account of the present investigation.10 EXPERIMENTAL PROCEDURE The experimental work was carried out on material produced from a 10 lb vacuum melted ingot, of composition 49.32 wt pct Co, 2.09 wt pct V, balance Fe. 30-mil thick sheet samples with a 1; in. gage section were machined from cold rolled stock. The degree of cold work ranged from 85 pct for the finest grained samples to 5 pct for the coarsest grain size. Details of ingot fabrication are reported elsewhere." Equi-axed grain sizes in the range 12.7 to 75.4 p were obtained by annealing for varying times at 850°C. (Re-crystallization annealing time, rather than temperature , was varied to control grain size to insure that samples of all grain sizes contained equivalent quenched-in vacancy and interstitial concentrations.) Grain sizes were measured by the line intercept method on several specimens of each grain size. Following recrystallization, all samples were disordered by quenching into iced brine.

Jan 1, 1970

By S. J. McCarroll

Fig. 1—The belt shown at right carries filter cake to mixing station over calciner. Crude ore conveyors appear in right background. THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.&apos; During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO2 process was constructed. Numerous operation difficulties ensued, and the plant. was closed when the manganese situation in the country eased. In 1949 Hewitt S. West initiated negotiations to acquire the plant. In 1951 Manganese, Inc., was formed and contract entered into with the General Services Administration to supply 27 million units of metallurgical grade manganese in the form of nodules to the national stockpile. A second contract was made to upgrade 285,000 tons of stockpile ore. Test work was undertaken by the Southwestern Engineering Co. and likewise by the Boulder City pilot plant at the U. S. Bureau of Mines. Results obtained indicated the commercial feasibility of the flotation process. Construction of the plant, which is shown in Figs. 1 and 2, was started in June 1951, and operations on a break-in basis began in September 1952. Apart from the usual starting difficulties two major disasters caused serious setbacks, one a kiln failure in February 1953, and the other a fire that destroyed the flotation building in June of the same year. The nodulizing section of the plant resumed operation in November, and the flotation section in January 1954. The ore minerals are chiefly wad,* with minor amounts of psilomelane, and occur in sedimentary beds of volcanic tuff. The ore is overlain with beds of gypsum which outcrop or may be covered with surface gravel. Intermediate beds of red and white tuff occur frequently with lenses of red and green jasper and stringers of gypsum and calcite. Small amounts of iron are present; lead content averages about 1.0 pct and minute amounts of copper and zinc are found. Barite, celestite, and bentonite are present. Since these are made up of minute asicular crystals, moisture content is very high, averaging about 18 pct. Ore reserves have been estimated at 3 million tons averaging 18 pct Mn2 and up to 5 million tons after grade is dropped to 10 pct Mn. A good part of the orebody was stripped of overburden by the previous operating company . Approximately 50 pct of the ore, representing more than 60 pct of the manganese, can be mined by open-cut methods. A system for underground min- . ing has not yet been decided on. Open-cut mining with benches of 20 ft has proved satisfactory. Although the ore is soft and appears dry and dusty it has a certain resilience, probably due to the porosity and moisture which makes drilling and fragmentation difficult. Wagon drills have been abandoned in favor of the Joy 225-A rotary drill which will put down a 43/4 -in. hole at the rate of 2 ft per min. Holes are spaced in a pattern with 8 to 9-ft centers. Forty percent powder has been used, but better breaking to 2-ft size is obtained with low velocity bag powder of 30 pct strength. Loading is done with one 21/2-yd shovel, and cleanup follows with one D-7 bulldozer. The ore is hauled with Euclid trucks about 1000 ft from the pit to a blending pile, where the daily mine production is spread in layers by bulldozing until approximately one month&apos;s mill feed is accumulated. A new pile is then started and mill feed is drawn from the first pile by one 13/4-yd shovel and Euclid trucks, with a haul of approximately 500 ft. Mining is performed by an independent contractor with engineering and supervision by the company staff. Early test work indicated that the manganese could be floated with soap, a wetting agent, and fuel oil to give a recovery of better than 75 pct with a grade of 43 pct Mn. The concentrate when nodulized with coke would upgrade to 46 pct Mn or over, and the lead volatilized to 0.6 pct residual.

Jan 1, 1955

By M. Kaitz

A continuing discussion in both the petroleum engineering and economic literature is directed to the difficulties encountered in the use of discounted cash flow rate of return (DCF) as a measure of investment worth. Although useful in most Instances, DCF has been criticized because it is time-consuming in its trial-and-error solution, theoretically invalid, not adaptable to cash flow streams yielding multiple return solutions and not entirely reliable in selecting between mutually exclusive investments. The theoretical invalidity of DCF stems from the reinvestment assumption implicit in the calculation that earnings are reinvested at the DCF rate. The emerging consensus of the economic literature is that the net present value or the present worth of the net cash flow stream (discounting at the average opportunity or cost of capital rate) is more correct and reliable. Other criteria proposed have been ratios of net present value divided by initial investment or by present value of all investments in a project. All of these criteria are simple to determine and explicitly assume a reinvestment rate for [he income generated by a project. This paper develops and discusses a theoretically valid profitability criterion which is simple to compute and retains the appeal of a percent return on investment. It is called "percentage gain on investment" or PGI. It measures the gain an investment is expected to realize over like capital invested in the average opportunity and explicitly considers reinvestment potential. Why add another Concept to the large array of investment criteria now available, any one of which, or perhaps a combination of several, appears to embrace the form&apos;s (or individuals) objectives? The answer is that not one of the existing criteria provides both a readily comprehensible and theoretically valid measure of risk coverage that has general application. The proposed PGI does fulfill these requirements. INTRODUCTION An ancient expression warns that "one must yield to the times" — there are better ways of doing things. A review of the petroleum engineering and economic literature on one topic alone, measurement of investment worth, certainly is witness to this truth. In use for a number of years, the DCF has recently received attention, directed mainly to its theoretical invalidity. Several alternatives to DCF have been proposed to provide a valid, simply determined criterion to describe investment worth and to overcome the criticisms previously mentioned. This paper introduces another method called percentage gain on investment (PGI) and is proposed as but one of several yardsticks that should be used in making investment decisions. MEASURES OF INVESTMENT WORTH This paper will consider only those criteria which give weight to the time pattern of future earnings. These criteria are usually compared with an average opportunity rate or cost of capital of the firm to judge the relative worth of the investment. For purposes of demonstration, a 9 percent average opportunity rate will be used throughout this paper. Implicit in the DCF calculation is the assumption that earnings are reinvested at the DCF rate. Some argue, though, that there is no reinvestment assumption,&apos; that the DCF rate is simply that maximum rate of interest one can pay on the investment over the life of the project and break even. The determination of DCF is accomplished by discounting the net cash flow stream at that rate (DCF) which will yield zero. The question is: why should reinvestment potential be explicitly considered in calculating return on investment or other criteria measuring economic worth? Perhaps the answer lies in consistent or equal treatment of future cash flow. It appears entirely illogical to give different present worth value to $1 received, say, 10 years from now, which is the circumstance resulting in comparing projects with different DCF returns. In fact, $1 received in 10 years has the same value regardless of which project generated the income. DCF return thus favors investment projects which are expected to provide early income as compared to those providing long-term income. Not surprisingly, the controversy on reinvestment assumption is an old one. Hoskold&apos; discussed this same problem in 1877. He considered the future income from mineral properties as an annuity or a series of fixed future payments. (As will be demonstrated, his equation can be modified for variable income.) Prior to Hoskold, the value or what one could pay for the mine, was determined with the use of standard, single-interest tables. Here is what Hoskold said with regard to these tables. "This table, and others of its kind, to be found in most works on annuities, is constructed correctly according to

By W. B. Dancy, A. Adams

Laboratory test work on heavy liquid separation of sylvite from halite is reported. Numerous tests were run on sylvite ore sized in the ranges of 4x20 mesh, 10x65 mesh, 8x100 mesh, -8 mesh and -10 mesh with heavy liquids in the range of 2.05 to 2.15 sp gr. From the test results, it was concluded that, with the type of ore under study and a size in the range of -8 mesh, a recovery as high as 90% could be achieved with a product grade of 70% KCl. However, a final product at an acceptable recovery cannot be made with one pass, and the float must either be further processed with heavy liquids or dried and sent to a conventional froth flotation circuit. Potash ores occurring in this country consist essentially of sylvite and halite plus minor amounts of magnesium sulfate salts and montmoril-lonite-type clays. Recovery of potash minerals from evaporite ores in the North American potash fields is accomplished almost exclusively by use of amine flotation. European practice involves froth flotation as well as solution-crystallization processes. Laboratory and pilot plant test work has been reported in Europe and the U. S. on the application of heavy media separation to potash ore beneficiation. Work was probably discontinued because of lack of ore with the required very coarse liberation characteristics (1/8 to 1/2 in. liberation size). Sylvite, with a gravity of 1.99, and halite, with a gravity of 2.17, appear to be ideal for separation by heavy liquids, which are now available in gravities from 1.59 to 2.95. This paper reviews preliminary results obtained from laboratory test work on heavy liquid separation of sylvite from halite. TEST WORK The heavy liquids used in the tests under discussion were chlorobromethane, with a specific gravity of 1.923, and dibromethane, with a gravity of 2.490. These liquids, completely miscible, were combined in the proportions needed to give a mixture having the desired specific gravity. Feed for the laboratory tests was mine-run ore screened to the desired mesh sizes. In conducting the tests, the sample was fed at a constant rate into a stream of heavy liquid and the mixture directed into a small separatory vessel. The float overflowed into a collecting pan while the sink collected in the bottom of the separatory vessel and was removed at the end of the test. Approximately 500 g of feed constituted a charge. Pulp density of the feed was kept low to prevent particle to particle interference in separation. With feed in the range of 8x100 mesh, a pulp density of under 10% solids by weight was found advisable. With coarser feed the pulp density could be carried as high as 15% solids. Time of separation was very rapid. In the case of 4x20-mesh material, separation was effected in 15 to 30 sec; with -10-mesh feed, separation required about 1 to 2 min. SPECIAL EQUIPMENT Since heavy liquids are toxic to varying degrees, all separatory work was carried out in a standard laboratory fume hood. It was noted that complete removal of fumes was not being effected; therefore the hood construction was modified, resulting in a completely satisfactory arrangement for heavy liquid test work. In the interest of safety, details of this fume hood are reported here. Unlike most fumes, heavy liquid fumes tend to settle and flow like water, rather than to rise like a gas. Working on this assumption, a standard water drain was installed in the hood. Across the front of the hood a 1-in. barrier was constructed. In the rear of the hood a false back was installed, with an adjustable sliding door on both the bottom and top of this panel. As shown in Fig. 1, the exhaust fan pulled a vacuum behind the barrier, sucking the heavy fumes from the bottom of the hood. Another addition was the drying box, shown to the right of the hood. This is simply a box covered on top with hardware cloth and connected by a 6-in. inlet to the hood. Sample trays made of fine mesh wire filter screens were found ideal for drying samples. With this arrangement, air flowed completely through the sample and all fumes were drawn into the hood. In use, it was found effective to cover with a

Jan 1, 1963

By J. H. Swisher

The solubility of sulfur and rate of solution of sulfur in pure Lron were measured in H2S + H2 and H2S + H2 H2O gas mixtures. The solubility and diffusivity of sulfur at 1410°Care 0.13 pet S and 1.0 x 10-5 sq cm per sec, respectively. The solubility iS the same, but the rate of sulfurization is slower in the presence of H2O in the reacting gas. Under these conditions, the over-all rate is controlled jointly by a slow surface reaction and by solid-state diffusion; the mechanism for the surface reaction has not been identified. KNOWLEDGE of the behavior of sulfur in solid iron is desirable for the metallurgy of such products as free machining steel, where a high sulfur level is required, and inclusion-free high-strength steels, where the sulfur specifications are very low. The present investigation was undertaken to check previously reported values for sulfur solubility and diffusivity in 6 iron, and to study the poisoning effect of chemisorbed oxygen on sulfurization kinetics in H2-H2S-H2O gas mixtures. All of the experiments were performed at 1410°C. The thermodynamic behavior of sulfur in 6 iron was the subject of a paper by Rosenqvist and Dunicz.&apos; The sulfur solubility at 1400" and 1500°C was determined by equilibrating pure iron specimens with H2-H2S gas mixtures. The maximum solubility of sulfur in 6 iron was alsc determined by Barloga, Bock, and parlee2 by reacting iron wires with sulfur in sealed capsules. In another investigation, the diffusion coefficient of sulfur in 6 iron at temperatures up to 1450°C was measured by Seibel.3 The method used was to measure sulfur concentration profiles in diffusion couples containing radioactive sulfur EXPERIMENTAL Apparatus. A vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction rube was used for the experiments. The hot zone in the furnace was approximately 2 in. long with a temperature variation of ±3oC. The hot zone temperature was automatically controlled to within ±2°C, and the test temperature was measured with a pt/Pt-10 pet Rh thermocouple before and after each experiment. Flow rates of the reacting gases were obtained using capillary flow meters. Materials. The source of H2S in the gas train was a premixed cylinder containing 5 pet H2S in H2. This mixture then was diluted with additional hydrogen and argon. In some experiments, water vapor was introduced by passing hydrogen and argon through a column containing 10 pet anhydrous oxalic acid and 90 pet oxalic acid dihydrate. The vapor pressure of water above this mixture is well-known.4 Argon was used as a diluent to minimize thermal segregation of H2S in the furnace5 and to reach higher H2O:H2 ratios than could be obtained in mixtures of H2 and H2S alone. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over P2O5. The specimen stock was made by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zirconia crucible. The principal impurities are listed in Table I. In some of the equilibrium experiments, six-pass zone-refined iron was used to minimize impurity side effects. This zone-refined iron had a total impurity level of about 25 ppm. Procedure. Specimens were annealed in hydrogen for a period of at least 2 hr at the beginning of each experiment. The specimens were held in the reacting gas for times varying between 10 min and 17 hr, and cooled to room temperature in a water-cooled stainless-steel block at the bottom of the furnace. The pH2S/pH2 ratios reported are those for gas equilibrium at 1410°C. Calculations based on available thermodynamic data8 showed that the only other gaseous8 species that formed in significant amounts in the furnace were S2 and S. Even when water vapor was introduced into the gas mixture, the concentrations of SO2, SO, and so forth, were negligible. The initial partial pressure of H2S was therefore corrected for its partial dissociation to S2 and S in determining the equi-

Jan 1, 1968

By Katherine Mather

This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. Results of the properties of these rocks on their performance as concrete aggregates are discussed. CRUSHED stone classified as limestone comprises about 70 pct of the crushed concrete aggregate and roadstone produced in this country, and the product has amounted in the recent past to about 97 million tons per year, valued at more than $123,-000,000.&apos; Therefore an evaluation of the properties of rocks classified in these statistics as limestones and an ability to predict their behavior as aggregate in portland cement concrete are matters of considerable economic consequence to producers and consumers of aggregate. This paper is an attempt to put together petrographic, physical, and chemical data about the large and varied group of rocks generally called limestones. It also points out certain results of the properties of these rocks on their performance as concrete aggregates. The problems encountered in efforts to explain the behavior of limestones, dolomites, and related rocks as concrete aggregate lie on the frontiers between the ignorance of the geologists and the ignorance of the engineers. The mineral composition and textures of the rocks have not been adequately explored and described, and the effects of mineral composition and texture on the performance of aggregates have been worked out in only a few cases. There are instances of unsatisfactory performance and some generalizations of those experiences. There are many more examples of satisfactory performance than of unsatisfactory, but there is practically no published information as to why a particular aggregate was satisfactory in a specific use. There are all too few investigations of undeteriorated concrete; more is known about the pathology of concrete than about its normal structure and aspect. As part of the investigation of aggregates, the classification of rocks is not an end in itself, but is a step toward recognition of properties expected to influence the behavior of aggregates in their intended use. Rock of any type may perform well or poorly as concrete aggregate, depending on the physical condition of the rock, its physical and chemical properties as compared to those of the matrix in which it is placed, and the circumstances under which the concrete is exposed. Some classification and descrip- tion of the limestones is necessary to distinguish subgroups whose members will probably behave in similar ways and to evaluate the group as a whole. The group name, limestone, includes and tends to conceal the identity of rocks that have a very great range in chemical and mineralogical composition, structure and texture, conditions of deposition, subsequent history, and suitability for use as concrete aggregate. All the rocks classified as limestones include one or both of the most abundant rock-form-ing carbonate minerals, calcite and dolomite, as major constituents. Carbonate rocks is a more descriptive and more accurate group name than limestone, which has generally been used to include dol-omitic or magnesian limestones and dolomites as well as calcitic limestones. Classification and Description of the Carbonate Rocks The question of names to be applied to the carbonate rocks may appear academic, but it is of practical importance as long as there are specifications for aggregate that result in acceptance or rejection of rocks by name and as long as failure to make distinctions among the carbonate rocks leads to misunderstandings of their properties and of what may be expected of them in performance. Materials included in production statistics as limestone and tested for concrete aggregate as limestone range in fact from calcareous shale and calcareous or dolomitic sandstone and argillaceous limestone and dolomite to calcitic limestone and pure dolomite and to rocks close to calcitic and dolomitic marble. To take a simple example: consider two manufactured coarse aggregates, both dense and unweathered, one composed principally of crystalline calcite and the other of crystalline dolomite, but both known as limestone. If each is used as coarse aggregate in a standardized concrete mixture with the same fine aggregate used in both cases, made into concrete specimens, and tested in accelerated freezing-and-thaw-ing, the test results will probably be quite different, because of the differences in internal bond and thermal properties between the two aggregates. As long as both aggregates are called limestone, the test results cannot be explained, or used except in a very limited way; if the aggregates are distinguished as limestone and dolomite and the consequent differences in texture and thermal properties are recognized, the results are reasonable. Classification of the carbonate rocks used as aggregate should be based on structure and on composi-

Jan 1, 1954

By K. G. Davis

Dilute alloys of silver and of thallium in tin have been solidijzed unidirectionally under controlled conditions, to study the segregation associated with a cellular interface under conditions where both thermal and solute convection are present. Autoradiography and radioactive tracer counting techniques were combined with electron-probe microanalysis to study both macro- and microsegregation. It was found that, for concentrations giving only small amounts of constitutional supercooling, cell formation had little effect on the macroscopic distribution of solute along the specimen. At higher concentrations the effective distribution coefficient was higher than that expected for a smooth interface. Node spacing was independent of initial solute content at lower concentrations, becoming greater as keff increased. Silver content at the segregation nodes of silver in tin alloys was independent of initial concentration and considerably in excess of the eutectic composition. SINCE the investigation of cell formation at advancing solid-liquid interfaces by Rutter and Chalmers,&apos; a large volume of work has been dedicated to the determination of solidification conditions under which a planar interface will break down into cellular form. Early experiments were explained satisfactorily by the concept of constitutional supercooling,2 but, due to poor measurement of temperature gradients in the liquid, lack of accurate data on liquid diffusion and equilibrium distribution coefficients, and uncertainty about the effects of thermal and solute convection, these experiments cannot be used as proof for the theory. More recent work, however, has shown that under conditions where convection is eliminated or can be ignored good correlation is observed.3,4 Investigations into segregation at cell caps5 and at cell nodes6-&apos;&apos; have been made, but no measurements appear to have been done on the overall, macroscopic segregation down a unidirectionally solidified rod of material which has solidified with a cellular substructure. This has practical importance in casting, where regions of material with cellular substructure are often encountered, and also in zone refining where the thermal conditions necessary for a planar interface are unattainable. Further, as will be shown, the macroscopic segregation can give information on the following question. Granted that a cellular solid-liquid interface develops from a planar one when the conditions for constitutional supercooling are exceeded, how much supercooling is present after the cells have formed? EXPERIMENTAL PROCEDURE AND RESULTS Specimen Preparation. Specimens 25 cm long with a square cross section 0.6 by 0.6 cm were grown in graphite boats by solidification from one end. Alloy compositions are given in Table I. Two specimens of each composition were grown. The tin was 5-9 grade and the silver and thallium both 4-9 grade. Ag110 and Tl204 were used as tracers. Each composition had the same quantity of tracer so that auto radiographs of specimens containing different concentrations of the same element could be easily compared. Thermocouples inserted through the lid of the boat into a dummy specimen showed that, over the first 10 cm of growth, thermal conditions were quite steady, with a rate of interface advance of 5.8 cm per hr and a temperature gradient in the melt ahead of the interface of 3.0°C per cm. The specimens were seeded from tin crystals of a common orientation to eliminate orientation effects. Dilution of the specimen by seed material was minimized by the provision of a narrow neck between specimen and seed crystal. Macrosegregation. After growth, the specimens were sectioned with a spark cutter. The rods of silver alloy were cut into 1-cm lengths and analyzed for Ag110 using a y -ray counter with fixed geometry. The specimens containing thallium were cut into 2-cm lengths and analyzed for T1 204 by taking 13 counts from each end of the cut lengths through an aperture in lead sheet approximately 0.4 cm square. The results are summarized in Figs. 1 and 2. To find the effective distribution coefficient for the silver in tin alloys under smooth interface conditions, the region of substructure at the bottom surface of one of the 10 ppm specimens, see Fig. 3, was removed by spark machining before counting. Autoradiography. For both alloy systems the samples were polished on sections taken alternately parallel and perpendicular to the growth direction, and autoradiographed by placing the polished surfaces in contact with Kodak "Process Ortho" film. Figs. 3 and 4 show the structures revealed. The alloy containing 10 ppm Ag showed substructure only after a few centimeters of growth, and then substructure was limited to a narrow layer at the base. The "speckled" substructure reported previously in this system4 is here clearly seen to be an intermediate stage between planar and cellular interface conditions. The other samples show a remarkable similarity considering

Jan 1, 1969

By Nicholas J. Grant, John S. Benjamin

A series of composite alloys containing a high volume of NiAl, Ni3Ah or CoAl, bonded with 0 to 40 vol pct of a ductile metal phase, were prepared by powder blending and hot extrusion. The binder metals were of four types: pure nickel or cobalt, near saturated solid solutions of aluminum in nickel and cobalt, type 316 stainless steel, and niobium. Sound extrusions were obtained in almost all instances. Studied or measured were the following: interaction between the alunzinides and the binders, room-temperature modulus of rupture values, 1500° and 1800°F stress rupture properties, hardness, structure, and oxidation resistance. Stable structures can be produced for 1800°F exposure, with interesting high-temperature strength and good high-temperature ductility. Oxidation resistance was excellent. A large number of experimental investigations have been made of the role of structure on the properties of cermets and composite materials. Gurland,1 Kreimer et al.,2 and Gurland and Bardzil3 have indicated the preferred particle size in carbide base cermets to be about 1 µ, with a hard phase content of 60 to 80 vol pct. The optimum ductile binder thickness was noted to be 0.3 to 0.6 µ.1 Complete separation of the hard phase particles by the binder is important in reducing the severity of brittle fracture.&apos; The purpose of the present study was to produce structures comparable to the conventional cermets, using a series of relatively close-packed intermetal-lic compounds rather than carbides as the refractory hard phase, and to study the effects of binder content and composition on both high- and low-temperature properties. The selected intermetallic compounds were particularly of interest because of the potential they offered in yielding room-temperature ductility. The highly symmetrical structures are known to possess high-temperature ductility and room-temperature toughness. Based on a ductile binder, the alloys were prepared by the powder-metallurgy route to avoid melting and subsequent alloying of the matrix, and were extruded at relatively low temperatures. It was expected that the composite alloy would retain useful ductility. In contrast, infiltration and high-temperature sintering led to alloying of the matrix and to decreased ductility. The systems Ni-A1 and Co-A1 were selected for this study. In the Ni-A1 system the compounds NiA1, having an ordered bcc B2 structure, and Ni3Al(?1), having an ordered fcc L12 structure, were chosen. In the system Co-A1 the intermetallic compound CoAl with an ordered bcc B2 structure was used. ALLOY PREPARATION The intermetallic compounds, see Table I, were prepared by using master alloys of Ni-A1 and CO-A1, with additions of either cobalt or nickel to achieve the desired compositions. The master alloy in crushed, homogenized form, was melted with pure nickel or cobalt in an inert atmosphere, cold copper crucible, nonconsumable tungsten arc furnace. The resultant intermetallic compounds were homogenized at 2192°C in argon, crushed, and dry ball-milled in a stainless mill to -100 and -325 mesh for the Ni-A1 compounds and to -325 mesh for the CoAl compound. Finer fractions were separated for some of the composite alloys. Several ductile binders were utilized. These included Inco B nickel, 5µ ; pure cobalt, 5 µ, from Sher-ritt Gordon Mines, Ltd.; fine (-325 mesh) niobium hydride powder; fine (15 µ) type 316 stainless-steel powder; and near-saturated Ni-A1 and Co-A1 solid-solution alloys, also in fine powder form. The niobium hydride was decomposed above about 700°C in processing of the compacts in vacuum to produce niobium powder. The Ni-7.1 pct A1 and the Co-5.3 pct A1 solid-solution alloys were prepared from pure nickel or cobalt and pure aluminum by nonconsumable tungsten arc melting under an inert atmosphere. The ingots were homogenized, lathe-turned to fine chips, and dry ball-milled in air to -325 mesh powder. These solid-solution alloys are designated NiSS and CoSS; see Table I. Subsequently the hard and ductile phases were dry ball-milled as a blend. Experiments clearly established the need to coat the hard particles with the ductile binder to optimize subsequent hot compaction by extrusion. Ordinary dry mixing usually resulted in nonhomogeneous alloys which were quite brittle. Conventional cermets are consolidated by liquid phase sinteiing or infiltration, which resulis in undesirable and uncontrolled alloying of the binder phase. For this study, a loose (unsintered) powder-extrusion process was emploved, minimizing reactions between binder and hard particle, thereby permitting much greater control of composition and structure. The constituent powders were first mixed in the desired

Jan 1, 1967

By Robert T. Ault

The nature of fracture in unnotched tensile and notched tensile sheet and round specimens and V -notched and precracked Charpy-type sheet specimens of both wrought stress -relieved and re-crystallized molybdenum was investigated over the temperature range of -78° to 300°C. The sharp rise in fracture stress, for unnotched tensile samples, as the temperature is increased above the brittleness transition temperature (Tb), is found to be a result of an increase in flow stress due to plastic constraint and an increased strain rate which results from the onset of necking at Tb . Quasi-brittle fracture in notched tensile samples is found to occur when the tensile stress at the elastic-plastic interface, beneath the root of the notch, reaches a maximum critical value, which is independent of test temperature over the range from —78° to 25°C, but dependent on microstructure. In the temperature range between 150° and 300°C, unnotched tensile and notched tensile samples alike are found to fracture by a ductile fibrous tearing process which is discontinuous in nature, as a result of the competition between the processes of tearing, through continued plastic flow, and local work hardening. Results from the V-notched and fatigue-cracked Charpy-type impact tests demonstrate that crack initiation is the governing factor in the low-temperature (-78° to 25°C) fracture process for molybdenum. In recent years, there has been considerable interest, and a commensurate number of investigations, concerning the duc tile-to-brittle transition in refractory metals. There has not developed, however, a satisfactory explanation for the uniaxial tensile fracture-stress transition which accompanies the well-known ductility transition. This matter therefore warranted investigation. In a similar manner, the increased importance of notched tensile strength values in evaluating materials and in design criteria requires a better understanding of the factors which control the fracture behavior of notched tensile samples. In a previous investigation1 of the nature of initial yielding and fracture in notched sheet molybdenum at room temperature, it was suggested that plastic constraint was the controlling factor in governing the fracture behavior of notched samples. The final portion of this investigation was concerned with the fracture toughness of molybdenum. Of particular interest was the comparison of effective surface energies for fracture in V-notched samples with fatigue-cracked, Charpy-type samples in order to ascertain the relative importance of the initiation and propagation phases of the fracture process. MATERIALS AND TEST PROCEDURE Sheet tensile, notched tensile, and V-notched Charpy specimens were prepared from 50-mil, stress-relieved molybdenum sheet.* Half of these specimens were vacuum-annealed for 1 hr at 1200°C and 7.5 x l0-5 Torr and furnace-cooled to produce a relatively uniform grain size of 0.30 mm diameter. Round notched and unnotched tensile specimens were prepared from warm-rolled and swaged 5/8-in.-diam bar.* These specimens were vacuum-annealed for 1 hr at 1350°C and 5 x lom5 Torr and furnace-cooled to produce a grain diameter of 0.11 mm. Material analyses in ppm were: C N O H Sheet 290 10 4 1 Bar 50 30 30 2 The unnotched tensile sheet specimens had a 1/4-in. gage width and a 1-in. gage length. The unnotched tensile round specimens had a 9/32-in. gage diameter and a 1-1/4-in. gage length. The sheet and round notch tensile specimens are shown in Fig. 1. All of the notched tensile specimens tested were tandem-notched in order to study the location and mode of fracture initiation. The tandem-notched specimens were carefully machined so that the largest variation in notch depth on a single specimen was 0.001 in. Thus, when fracture occurs, the extent of plastic deformation that exists in the un-fractured notch section is that which exists just prior to fracture. All of the tandem-notched sheet specimens were electrolytic ally polished and chemically etched prior to testing. The V-notched Charpy-type specimens machined from the 50-mil sheet material had the standard dimensions of 2.125 in. long, 0.394 in. deep, and a 0.010-in. root radius. The unnotched tensile and notched tensile tests were conducted over the temperature range of -78° to 300°C, in a 10,000-lb Instron Universal Testing Machine, at a constant crosshead speed of 0.020 in. per min. The V-notched Charpy-type

Jan 1, 1964

Report was made by the Committee of National Engineering Societies on the Reserve Corps of Engineers and it was voted that a committee of - three be formed-consisting of the President of the Institute, Dr. Henry -S. Drinker and the Secretary of the Institute-to select members in different parts of the country to-advise with the local U. S. Engineer Officers as to qualifications of applicants for the Reserve Corps of Engineers.

Jan 8, 1916

By William Kelly

An exploring-drift, on the bottom level of the Curry mine, at Norway, Mich., on the Menominee range, cut a stream of water, which increased considerably the expense of pumping. The hope that the supply would drain off was not realized. It was decided to build a dam in the exploring-drift, as it was estimated that the cost would be recovered by the saving in fuel in less than two months.

Jan 1, 1898

By Simon D. Handelsman, Reg M. M. Rowe

The mechanism of using gold as the basis for a loan was suggested to the treasurer of a mining company operating two gold heap leach mines at a time of high interest rates. Due to the seasonal nature of cash flows from operations, and the relatively low cost of funds this scheme was attractive. The paper describes the agreement with the bank, gives an example of the transactions, and describes other types of gold loans.

Jan 1, 1985

By Ed Ramsay

The Kerr Addison process involves the cyanidation, flotation, and roasting of graphitic gold ore. The grinding and treatment section of the present mill has at the present time a capacity of 1400 stpd and the precipitation section has a capacity of 6000 stpd. The grind is maintained at 80%, -200 mesh, and a gold recovery of 92% is obtained in the cyanidation circuit. With flotation and roasting, the overall gold recovery is increased to 98%.

Jan 1, 1978

By Donald P. Richards, John F. Abel

Geotechnical site investigation for new mine shafts can reduce the level of design uncertainty for shaft linings. The parameters which determine the lining strength required include rock strength and hydrologic properties, the in situ stress conditions, and the concrete strength. These parameters are applied to analytical methods of shaft lining design using the plastic and clastic assumptions of rock response to determine the required lining thickness to maintain the stability of the shaft excavation.

Jan 1, 1982

By H. B. Pulsifer

ONE of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years&apos; work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition.

Jan 1, 1931

By D. M. Clippinger, J. J. Eidel, J. E. Frost

At Ithaca Peak, one of three peaks situated on Duval Corporation's Mineral Park property, a 'Single pulse of quartz monzonite magma intruded the isoclinally folded Precambrian Cerbat complex consisting of schist, quartzfeldspar gneiss, and amphibolite. The magma reacted with the Precambrian rocks, yielding a quartz-diorite rim. As the magma crystallized within the rim, it produced, progressing in'ward, annular bodies of quartz monzonite porphyry, quartz porphyry, and a distinctive quartz porphyry containing abundant podiform, tabular, and irregular quartz masses. These quartz masses are spatially associated with discontinuous crenulate and tabular quartz veinlets. Following crystallization, the Ithaca Peak stock and part of the surrounding Cerbat complex were fractured, producing a stockwork of predominantly northwest and northeast-trending fractures. The stockwork was then mineralized during a period of decreasing temperature by: ( 1) quartz-pyritechalcopyrite veinlets without distinct selvages and with distinct alteration envelopes in which orthoclase was altered to quartz and sericite; (2) quartz-pyrite-chalcopyrite veins and veinlets with distinct selvages and without distinct alteration envelopes; and (3) pyrite-chalcopyrite- galena-sphalerite veins. The Ithaca Peak stock was pervasively sericitized or argillized. The Mineral Park property is surrounded by a zone of propylitization Alteration and mineralization are coextensive in space and were, at least in part, coincident in time. The Mineral Park property possibly was elevated and exposed twice prior to its present exposure. The protore has been enriched by a factor of three. The Ithaca Peak supergene ore body is conformable with present topography and lies above the present water table. The shape of the ore body was controlled by erosion and oxidation of the previously enriched mineralization. Hematite, goethite, and jarosite present at the surface indicate a high primary pyrite environment, but it is possible to recognize that a small proportion of veins and veinlets contained greater amounts of chalcocite and chalcopyrite than pyrite. The igneous facies on Ithaca Peak are the products of differentiation within a solidifying rim according to Bowen's Reaction series. The innermost facies contain more quartz and orthoclase than the outer facies. Late magmatic quartz in the case of Ithaca Peak contains small amounts of pyrite and molybdenite. It is suggested that this quartz-sulfide mineralization, may also have been the product of differentiation the product of differentiation, may indicate that the later hydrothermal mineralization may also have been the product of differentiation.

Jan 1, 1968