Search Documents

By W. L. Fink, R. S. Archer

THIS paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent. beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium does not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. COMMERCIAL POSSIBILITIES OF BERYLLIUM ALLOYS Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to the strength and corrosion resistance of the aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

Jan 1, 1928

By George Harrington

THIS paper is a brief description of the design and equipment of a new coal mine in southern Illinois, which has many features not common practice in shaft coal mining and which is laid out and equipped for such unusually large capacity that it promises soon to become one of the largest mining operations of its kind. Shaft sinking for the mine, New Orient, was commenced in May, 1921, by the Chicago, Wilmington & Franklin Coal Co. In October, 1924, the plant was practically completed and was producing over 6000 tons of coal per day. There is good prospect that within a few years, when the mine is fully developed and manned, the output will attain a daily rate of 12,000 tons. The coal seam at New Orient lies approximately horizontal, about 500 ft. below the surface, and may be said to run from 9 to 12 ft. in thickness. The tendency in Franklin County has been toward large mining units (5000 to 6000 tons per day) with great care being given to protection against fire and explosion hazards, and usually with quite elaborate surface plants permitting careful preparation of the coal into graded sizes comparable with those made in the anthracite region. The field is unionized, with uniform conditions of wages for various classes of work, hours, etc., and the Illinois mining laws are quite specific with regard to fireproofing and safety measures. These conditions make it difficult for any but well-equipped and well-operated mines to meet the competition of the numerous fine properties of which this county can justly be proud. The coal company's property was already developed on the western side by the Orient. mine-a much visited and written about operation (with which many of you are possibly familiar through the Department of Mines' film "The Story of Coal ") which until recently held the 8-hr. production record with 8218 tons and usually ran quite consistently with production of slightly over 6000 tons per day. Experience at Orient was naturally one of the greatest influences in determining the location and character of the New Orient.

Jan 2, 1925

By A. S. Richardson

THe conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Go. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on, The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are: heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 1, 1923

By H. A. Doerner

The process for smelting zinc developed several centuries ago is still in use. Through the experience accumulated over this long period of time, details of the process have been perfected until there is little opportunity to make any further improvement except by a radical change in method. Such a change was accomplished by the process recently developed by the New Jersey Zinc Co. The process to be herein discussed is a still more radical departure, which has been developed to large-scale laboratory operation by the Metallurgical Division of the U. 5. Bureau of Minesl. † The reduction of zinc oxide by carbon is a highly endothermic reaction, which requires temperatures in the range 1200° to 1400' C. for even a slow reaction rate. The transfer of the heat of reaction through thick fire-clay walls, the high radiation loss in the type of furnace used, and the practical impossibility of recovering or using the combustible products of the reduction (CO) cause a deplorable waste of fuel. With the one exception mentioned, all zinc smelting is done in small retorts manually charged and discharged. Attempts to mechanize these operations have been only partly successful, and there seems to be no way to avoid or improve the uncomfortable conditions in which the work is done. The reduction of zinc oxide by methane has a relatively high reaction rate at 1000' C. At this temperature most ore residues do not sinter, and it is possible to use metal retorts. These factors make gaseous reduction especially adapted to a continuous operation and compared to reduction by carbon make possible: (1) higher rate of reaction at lower temperature, (2) more nearly complete extraction of the zinc, and (3) much better utilization of fuel and reagent. Although the reaction between methane and zinc oxide requires 105,900 calories per mole, compared to 86,860 cal. in the carbon reduction, it is obvious that much less fuel will be required to supply 105,900 cal. through 36 in. of metal at 1000' C. than to transfer 86,860 cal. through 1 in. of fire clay at 1300° C. Moreover, the gaseous products of gaseous reduction (CO and H2) can supply 183,430 cal. by complete combustion.

Jan 1, 1937

By A. S. Richardson

THe conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Go. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on, The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are: heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 1, 1923

By C. E. Sims, G. A. Lillieqvist

The following presentation is more a summation of observations made and conclusions drawn over a period of three to four years than a report of experiments made with a definite objective. Tests were made, of course, to verify hypotheses, but the large mass of data was collected incidental to other work. Lack of space forbids the presentation of more than a few of those data. On the other hand, it is unfortunate that some of the most illustrative examples are not available. The work is admittedly incomplete but is presented in the hope that it will stimulate further work along a similar line. The answers to many of the questions left unanswered by this paper will be found only after long and painstaking study, such as is scarcely possible in a commercial laboratory where problems of immediate importance consume most of the time. It is also hoped that this study will in some measure throw light on some of the dark spots of steelmaking, and help to clarify some of the annoyingly vague references to "good practice." Only cast steel was studied and the conclusions apply to cast steel, but it is the authors' opinion that the quality of rolled or forged steel is largely dependent on the quality of the ingot, which is a casting. Although this discussion deals almost entirely with inclusions, it is important that the reader understand that only those natural inclusions which owe their origin to the solubility of certain materials in steel and to the chemical reactions of steelmaking are considered. Accidental inclusions, such as entrapped particles of slag, nozzle, runner, or mold arc outside its province and are not considered. Such accidental inclusions are always dangerous and should be carefully avoided. Relation between Ductility and Nonmetallic Inclusions In September, 1928, an acid electric furnace was put into operation at the Indiana Harbor plant of the American Steel Foundries. Following the usual practice, aluminum additions were made in order to obtain sound castings. Immediately the problem of low ductility arose. Previous to that time, only open-hearth steel was produced, and, aluminum being used rarely in that steel, there had been practically no trouble with low ductility in the lower carbon range.

Jan 1, 1932

By A. S. Richardson

THE conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Co. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on. The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are : heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 2, 1922

By David B. Brooks

INTRODUCTION Resources are not; they become (Zimmermann 100) . The companion concepts of reserves and resources appear, one way or another, in almost all considerations of mineral supply. Yet, no other concepts in the economics of the mineral industries have occasioned so much confusion. Whereas everyone agrees that in general the terms refer to the amounts of material that-depending upon technology, market conditions, and institutions-will become available for production in the near or more distant future, the apparent agreement disappears when we come to more specific definitions or to application of the definitions. Some definitions emphasize the physical aspects of reserves and resources, while others emphasize the economic. Some treat reserves and resources as fixed quantities, while others regard them as continually varying. Some consider that reserve and resource estimates have validity only for individual deposits, while others insist that they can be measured with sufficient accuracy for regional or national planning. This confusion in concepts that lies at the very heart of mineral economics is both strange and not so strange. It is common in the social sciences to find concepts that have been adopted into scientific jargon from popular usage and given rather special meanings -at the same time that they continue to be widely used without such qualifications. Psychologists have the same trouble with personality and sociologists, with community. Nevertheless, an attempt must be made to straighten out the various meanings of reserves and resources, or at least to clarify the conditions under which different meanings are applicable, before much progress in analysis of mineral problems can be expected. That is the objective of this chapter. Throughout the chapter, an attempt has been made to provide enough references to guide the interested reader to the most pertinent works on the concepts under study. However, even in a review article, it is no longer feasible to provide a comprehensive set of citations; there are simply too many. In many instances the works cited will themselves include the bibliographies needed to complete a literature search; those that are particularly useful in this respect are so noted. Also, because of the limited availability of foreign periodicals, some important works -originating largely in Canada, France, the

Jan 1, 1976

By Hansheinz Portisch, Harold Margolin

A surface expansion was found to occur sometime after etching in Ti-A1 alloys containing 9.5 to 12.5 wt pct Al. The structure formed, grew, and disappeared with tzrrze. The surface expansion was followed by microscope observations and interferometric and lattice parameter measurements. Activation energy measurements for the growth of the "expansion structure" and chemical analysis indicated that the phenomenon occurred as a result of hydrogen pzckup during etching. It is proposed that hydrogen initially enters octahedral sites of Ti3Al coherent with a Ti and later shifts to the tetrahedral sites. It is postulated that expansion occurs when hydrogen enters the tetrahedral sites. The expansion structure disappeared, it is proposed, because of diffusion of hydrogen from the surface into the body of the alloy and because of loss of coherency of Ti3Al. In examining Ti-A1 alloys, Ence and arolinl observed markings on the surface of specimens. These markings did not appear after electropolishing only, but rather appeared only after etching. The markings appeared to grow as a function of time after etching and later seemed to disappear. Although the markings had some similarity to precipitates, showing, frequently, a Widmanstatten type of arrangement, the observation that other microstructural markings continue to be seen within the new structure suggested that it was actually not a precipitate. The source of this structure was unknown and an attempt was made in the present investigation to develop some understanding of its nature. It has been labeled expansion structure. 1) EXPERIMENTAL PROCEDURE A) Alloys. Alloys in the range 6.5 to 14.5 wt. pct A1 were studied. Bars, 4 in. sq, forged from Bureau of Mines (73 Bhn) titanium consumably arc-melted 4-lb ingots,' as well as 50-g arc-melted buttons of desired aluminum contents were used. The 50-g buttons also used Bureau of Mines titanium (73 Bhn) and aluminum of 99.99 pct purity. Buttons containing up to 8.5 wt pct A1 were hot-rolled from a furnace at 900' . Those with higher aluminum contents were hand-forged on a titanium anvil, and heated with an oxygen-hydrogen torch in the region of 1200" to 1300°c. Frequent reheating kept the samples at the desired temperature range. After a reduction of about 30 pct, the samples were water-quenched. To eliminate any contamination picked up either during hot rolling or forging, at least 1 mil of the surface of the sample was taken off. B) Heat Treatment. Prior to heat treatment all alloys were vacuum-annealed to remove hydrogen. Samples were annealed at 900' until a vacuum of 10'5 mm Hg was established. After this treatment, the samples were wrapped in molybdenum sheet and heat-treated in argon-filled quartz capsules, which were broken under water or iced brine at the conclusion of the heat treatment. All heat treatments under dynamic vacuum were performed in a rapid-quench furnace. This consisted of a molybdenum-lined quartz tube attached to a vacuum system and through a stopcock to a beaker of water. At the completion of the heat treatment the vacuum stopcock was closed, the furnace shut off, and dropped below the quartz tube. Then immediately the inlet stopcock was opened and water admitted until the tube was filled. The steam formed was allowed to escape through the inlet stopcock. This method was used in heat treatments up to llOO°C. C) Metallography. Specimens for metallographic examination were ground, then electropolished using a Disa Electropol machine with a perchloric acid electr01te. Specimens were etched with R-etch.3 A standard etching time of 3 min was used, with the specimen being agitated during immersion. D) Sample Preparation for X-ray Analysis. Samples 0.2 to 0.5 mm in diam were produced from heat-treated rods which were turned to 2 mm diam on a lathe and then rotation-etched. An etchant consisting of 1 pt HF, 7 pt HN03, and 12 pt HzO was satisfactory. With the rod rotating in a vertical position at 50 to 100 rpm, a needle with uniform dimensions could be obtained. Care had to be taken to insure that the rod was at the center of rotation, otherwise cavitation developed. If a small unevenness developed, it was possible to grind it off with a fine emery paper. E) X-ray Diffraction. All X-ray work was done on a North American Phillips X-ray diffraction apparatus and a Jarrell Ash microfocus X-ray unit. The Phillips unit was used with a copper target and nickel filter. The Jarrell Ash unit was fitted with a cobalt target and iron filter. For the Phillips unit 35 kva and 20 ma were used, whereas for the microfocus unit with the 100-p fixed-focus gun 40 kv and 1.5 ma were used. It was found that alignment of cameras on the Jarre11 Ash unit was very critical. The X-ray beam contains an intense area which is not the beam center. The cameras were aligned with the intense region by monitoring the beam coming out of the camera with a Geiger counter. Adjustments were made until a maximum intensity was obtained. A Phillips diffractometer with a Brown chart recorder furnished some of the lattice parameter data. The divergence slit up to 80 deg 28 was I deg; above 80 deg, a 4-deg opening was used, while the scatter slit was1 deg and the receiving slit had a 0.003-in. opening. The general scanning rate was 1 deg per min, while peaks of special interest were rescanned at -j deg per min. For elevated-temperature X-ray diffraction a Uni-cam High Temperature Camera with a film diameter

Jan 1, 1969

By Walter O. Snelling

Discussion of the paper of WALTER 0. SNELLING, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. C. McLAUGHLIN, San Francisco, Cal.-It seems to me that Mr. Snelling's work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out iii the last 25 years. If his end products are what they seem to be, he has made a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750°F. and pressure of 750 lb. per square inch. WILLIAM A. WILLIAMS, San Francisco, Cal.-What metal did you use, Mr. McLaughlin? - A. C. McLAUGHLIN.-Ordinary seamless tubing, extra strong. WILLIAM A. WILLIAMS.-Tests were made in Dr. Rittman's experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Rittman's plant, yields of from 43 to 58 per cent. of material, boiling under 150°C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. BEST, New York, N. Y.-What is the difference between the Rittman and the Snelling process or system? WILLIAM A. WILLIAMs.-The fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By J. B. Cohen

EARLY investigators1-4 reported that additions of beryllium to silver caused embrittlement. The in-termetallic phases which are now known to exist5,' were not known at the time. Solidification appeared to occur by a simple eutectic reation.4,7 (The primary beryllium-rich phase appeared globular, when the liquidus temperature was near the melting point of pure beryllium, and angular when the liquidus was much lower; in discussion of Sloman's work,4 it was suggested that this difference was due to an intermetallic compound which was not revealed by the polishing technique.) In the investigation reported here, it was found that if the compounds now known to exist were avoided, certain beryllium-silver alloys containing large amounts of the primary beryllium phase possessed sufficient ductility to be cold formed. Alloys containing 14 and 20 at. pct Ag were prepared from vacuum-cast beryllium containing 1.0 to 1.2 pct impurities and silver, 99.99+ pct pure. The elements were melted together by induction in beryllia or alumina crucibles under argon at less than 1 atm pressure. The cooling rate was adjusted by regulating the temperature of the melt and by reducing the power to zero without stopping the water flow in the induction coils, which were in contact with the crucible. Ingots were about 0.75 in. in diam with a grain size of 0.12 to 0.25 in. Microscopic investigation of transverse or longitudinal sections of an ingot cast from a temperature well above its melting point showed that, in general, the compounds did not form, presumably because of rapid cooling; the alloys consisted of beryllium-rich particles in a silver-rich matrix as shown in Fig. 1. A eutectic structure was not observed, probably .due to the low beryllium concentration of the eutectic composition and eutectic divorcement. Within a given grain, the small globules of the primary phase were all oriented in the same direction, as indicated by examination under polarized light; the orientation varied from grain to grain. This suggested that the globules were branches of the same dendrites. If cooling was too slow, a third constituent was observed in the microstructure; because it formed around the primary beryllium-rich globules it was Fig. 1—Ag-Be alloy, 18.6 at. pct Ag, as-cast. Bright field illumination. Etched with an aqueous solution of NH,OH and H2O2. X500. Reduced approximately 21 pct for reproduction. probably the 6 compound. A thin ring around an ingot often contained this constituent. When this compound was present in large quantities, or the silver segregated so that large regions occurred with the beryllium-rich globules in contact, sections from the ingot were brittle. When the compound was initially absent, it was possible to carry out reductions in thickness of 50 pct by cold rolling with only limited edge cracking; failure did not occur until reductions of 80 pct. A typical cross section after cold rolling is shown in Fig. 2. After simple bend tests, microcracks were found; these apparently were difficult to propagate in the two-phase structure, as the specimens continued to behave in a ductile manner after the cracks appeared. Similar cracks would probably be closed during rolling. It is apparent in Fig. 2 however, that the primary beryllium particles undergo extensive plastic deformation. Hardness values of the alloys indicated that some work-hardening occurred during cold working. Fig. 2—Ag-Be alloy, 18.6 at. pct Ag, reduced 83 pct in thickness by cold rolling. Bright field illumination. Etched with an aqueous solution of NH,OH and H2O2. X500. Reduced approximately 21 pct for reproduction.

Jan 1, 1961

By C. S. Smith, Chih-Chung Wang

TURNBULL and his collaborators1,2 have developed the theory of homogeneous nucleation as applied, inter alia, to solidification of liquid metals. Vonnegut³ and Turnbull4 have shown that if a liquid metal is subdivided into small droplets a vast majority of them will undercool very considerably before solidification, generally to as low as about 0.8 of the freezing temperature on the absolute scale. The nuclei effective at small degrees of supercooling in bulk metal seem to be internal or surface heterogeneities, relatively small in number. If the metal is subdivided, those droplets that happen to contain such nuclei will solidify at a temperature not greatly below the true freezing point, but only a small part of the whole volume will be affected and the majority of the drops will under-cool to the much lower temperature at which homo- geneous nucleation occurs as a result of fluctuations. It occurred to one of the authors that an appropriate subdivision to give effective freedom from random nuclei is produced during the solidification of many alloys that contain a minor amount of a phase of low melting point, and that one might then expect marked undercooling of the distributed phase. Experimental: The alloys selected for initial study were copper with minor amounts of lead and bismuth, and aluminum with tin. In all these alloys, the major component freezes at a temperature not much below that of the pure metal, and there is little further change in constitution on cooling until the lower melting point constituent freezes in an almost pure state. Cooling curves were taken using the controlled heat flow method permitting approximate specific heats to be obtained. Chromel-alumel thermocouples were used, with the standard emf tables, since extreme precision was not needed. The crucible (3/4 in. id, 5/16 in. wall) was made of B & W K-20 insulating brick. It held about 10 cc of the alloy being investigated. The cooling rate was 2.5" to 2.9°C per min under a controlled temperature difference of 20°. Approximate specific heats were computed from the inverse rate curves together with data from a blank run and from a standard run with a copper cylinder of known heat capacity. The alloys for investigation were made from high-purity metals (99.99+pct) and cast into graphite molds. The castings were machined to fit the crucible and to provide a hole for the inner thermocouple. Cooling curves were taken after heating to a temperature about 50" above the melting point of the minor, lower melting-point, constituent. Results The lead phase in an alloy of copper with 5 pct lead did not undercool more than 3" below the melting point of lead (327°C) either as cast or after annealing to produce a new dispersion of the liquid phase. A copper-zinc-lead alloy with 23.75 pct zinc and 5 pct lead undercooled more but showed no thermal effect below 319°C. A cast alloy of copper with 5 pct bismuth undercooled to 249°C (M.P. bismuth 27l °C), but once solidification started it was completed at the same temperature. This was anticipated, since the bismuth forms a nearly continuous phase between the grains of copper, and a solid crystal nucleated anywhere would rapidly* con- sume the entire network of liquid, unless the physical continuity of the liquid were broken through volume changes, inadequate fluidity, or gas evolution. Similar arguments apply in the case of copper-lead alloys, where the lead-rich liquid forms a network along grain edges, though not grain faces. In both cases there would be a few isolated particles

Jan 1, 1951

By R. Schuhmann, E. J. Michal

Experimental measurements are reported for the oxygen pressures of iron-silicate slags in equilibrium with solid silica. CO2-CO mixtures were bubbled through the slags in silica crucibles to find equilibrium values of p co2/p co over the entire composition range of silica-saturated slags at 1250°, 1300°, and 1350°C. From the data, the activity vs. composition relationships were calculated for O, FeO, and Fe. SLAGS composed primarily of silica and iron oxides have particular practical importance in copper smelting,' in acid steelmaking, and in accounting for the service behavior of silica refractories. These slags all contain both ferrous and ferric iron, so that, strictly speaking, they are ternary or three-component liquid solutions. For convenience, the components may be taken as the three oxides, FeO, Fe2O3, and SiO2. The constitution of the FeO-Fe,O,-SiO, system at slagmaking temperatures has been studied in a recent investigation described in a separate paper.' This work showed the compositional ranges of iron-silicate melts at temperatures up to 1450°C and also the temperature-composition relationships for melts in equilibrium with various solid phases, including iron, wüstite, magnetite, and silica. Broadly speaking, the compositions of iron-silicate melts at a given temperature should be thought of as varying over a two-dimensional field. In the first place, the silica/total iron oxide relationship varies from maximum silica for silica-saturated melts to minimum silica for wüstite-saturated melts or, at higher temperatures, to zero silica for straight iron oxide melts. In copper smelting, for example, the converter slags approach the low silica limits while the reverberatory-furnace slags have intermediate silica contents, perhaps approaching silica saturation in some circumstances. Liquids formed in the pores of silica refractories presumably are close to silica saturation. The second type of composition variation is in the ferric/ferrous relationship, which depends on how oxidizing or how reducing the process conditions are. Relatively reducing slags, such as acid-steelmaking slags, are lower in ferric oxide and ap- proach saturation with metallic iron. Oxidized slags, such as copper-smelting slags, contain larger percentages of ferric oxides and approach or reach saturation with magnetite. Since these two kinds of compositional variations are closely related to two general properties of interest for all metallurgical slags, basicity, and oxidizing power, it is hoped that the thermodynamic study of iron-silicate slags eventually will throw further light on the significance and nature of these long-recognized but as yet poorly understood slag properties. Measurements of oxygen activity as a function of slag composition, using CO-CO2 gas mixture to fix oxygen activities, afford an experimentally convenient approach to the study of the thermodynamic properties of iron-silicate slags. In a preceding investigation,³ his approach was used in a systematic study of iron-silicate slags in equilibrium with solid iron. The present paper gives the results of a similar study of the iron-silicate slags in equilibrium with solid silica. The experimental work consisted in the determination of CO2: CO ratios in gas mixtures at equilibrium in the system: gas: liquid slag: silica Determinations were made at temperatures from 1250° to 1350°C for slags ranging in composition from iron saturation to magnetite saturation. Also, equilibrium CO,: CO ratios and slag compositions were determined for the univariant systems: gas: liquid slag: silica: iron gas: liquid slag: silica: magnetite Experimental Methods The experimental procedure was essentially the same as that used in the previous study of iron-silicate slags saturated with solid iron," but in order to work with the silica-saturated slags an all-silica crucible assembly was used. A liquid slag was prepared from pure prefused stock materials and brought to equilibrium with the silica crucible at the desired temperature. Then a mixture of CO2 and CO was continuously bubbled through the melt

Jan 1, 1953

By R. E. Reed-Hill, W. H. Hartt, W. A. Slippy

An unusual form of double kinking has been observed at the ends of {1121} twins in deformed zirconium. These kinks lie partly outside of the twin and partly inside. While they are undoubtedly closely associated with accommodating the twinning shear into the matrix, they are apparently closely related to other important aspects of twin growth. A mechanism is proposed for {1121} twin growth involving interactions between 1/3 (1120) dislocations in the bend planes and twinning dislocations. It is also shown that boundaries without long range strain fields develop at the tapered ends of the twins. The {1121} twins can, therefore, grow without forming high-energy noncoherent twin boundaries containing large numbers of closely spaced twinning dislocations. NUMEROUS investigators have indicated that slip is often closely associated with deformation twinning. An example is twin accommodation kinking,1-3 where dislocations form bend planes and permit accommodation of a twinning shear within the parent crystal. Another is the incorporation of slip dislocations into twins, as proposed by Sleeswyk and verbraak4 and Ishii and Kiho5 for iron and ß-tin, respectively, and observed in hcp metals by Price.6 In addition, it has been shown that shear discontinuities exist at the points of twin intersections in zinc,7 magnesium,8 titanium,9 ß-tin,10 and bismuth," where the continuity conditions for twin intersections, originally proposed by cahn,12 are not satisfied. A similar situation occurs for zig-zag (1121) twins in zirconium13 and ?-phase silver-aluminum alloys,14 where the twinning shears of the two component twins are not parallel. In all these latter cases additional deformation by slip is believed to accommodate the twinning shear discontinuity. The present paper is concerned with a newly observed aspect of the slip and twinning interrelation, in which two kinks, one inside the twin and the other external to the twin, are formed. These kinks, observed in conjunction with (1121) twinning in zirconium, form to accommodate the twinning shear. A model has been constructed explaining the growth and accommodation of (1121) twins in terms of these kinks. This mechanism may be significant since it is concerned with an important twin mode, which occurs not only in zirconium but also in titanium and hafnium. The practical significance of (1121) twinning has been adequately demonstrated. At 77° K the high ductility of zirconium containing a large number of grains unfavorably oriented for slip is primarily due to (1121) twinning.'5 Also, (1121) twins nucleated at 77°K may grow during further deformation at room temperature. This growth can greatly increase the transverse ductility15 as well as produce large mechanical hysteresis effects.= EXPERIMENTAL PROCEDURE Arc-melted, sponge zirconium plate previously described17 was prestrained 0.65 pct at 77° K by cold-rolling to introduce {1121} twins into the structure. Tensile specimens were cut with axes normal to the plate rolling direction. These specimens were pulled in tension to near the point of failure in an Instron machine at room temperature at a cross-head speed of 2 x10-2 in. per min. This additional deformation caused growth of the twins nucleated by prestrain. Deformed specimens were then prepared for metallo-graphic examination. This included an anodizing treatment18 that made the surfaces sensitive to polarized light, permitting small lattice rotations to be revealed. EXPERIMENTAL RESULTS Nature of the Twin-Kink Band Structure. Fig. 1 is a photomicrograph of a typical specimen after prestrain at 77° K. The structure is characterized primarily by long, narrow, parallel sided (1121) twins which norma1ly traverse the entire grain. Fig. 2 shows several (1121) twins after additional straining at room temperature. These lie near the center of the polarized light photomicrograph and are inclined upward to the right. It is evident that this latter deformation has resulted in appreciable twin growth. The dark regions extending from the ends of these twins are accommodation kinks. The difference in reflected light intensity indicates the

Jan 1, 1969

By E. T. Hayes, A. H. Roberson, M. H. Davies

ZIRCONIUM has been produced on a pilot-plant scale for only a few years, but the potential uses have led a large number of research establishments to engage in a thorough study of the metal and its alloys. The work described in this paper is part of a cooperative project between the Bureau of Mines and the Air Materiel Command. The Zr-Cr system was one of the first investigated because of the possibilities of improving the properties at elevated temperatures, the chemical corrosion resistance, and the mechanical properties of zirconium in a manner similar to the enhancement of the properties of titanium by additions of chromium. There is no published work on the Zr-Cr system but from the similarity of the metals involved it was expected that it would be similar to the Zr-Fe' and Ti-Cr' systems. The materials used in this investigation were prepared in the Bureau of Mines laboratory at Albany, Ore. Zirconium was produced by magnesium reduction of zirconium tetrachloride, and a typical analysis is as follows: Fe, 0.06 pct; Ox, 0.08; N?, 0.01; C, 0.02; and other impurities such as Al, Pb, Ni, Ti, and Si less than 0.01 pct each. High purity chromium was prepared by treating crushed electrolytic chromium in a stream of dried and purified hydrogen." The resulting powder contained about 0.01 pct 0 and about 0.1 pct total metallic impurities. All alloys were prepared by arc-melting 50 g briquetted compacts of the desired composition in a Kroll-type" arc furnace using an inert atmosphere. The furnace was evacuated twice and backfilled with helium, which was gettered by melting a center zirconium button immediately before the alloys were melted. Alloys were remelted at least once to insure greater uniformity of composition and subsequently were annealed in vacuum at 1250°C for 48 hr. Fairly homogeneous alloys were obtained by this means; a slight loss of chromium from the surface by evaporation during the high temperature homogenization was noted. All alloys were analyzed for chromium and gave results in good agreement with the nominal composition. Spot checks on tungsten and nitrogen showed pick-up of these elements to be negligible. Over 70 alloys were prepared for use in this investigation; only the critical ones are shown in Table I. Alloys containing up to 10 pct Cr were amenable to hot working at 850°C and a number of these were sheath rolled to 1/16 in. thickness. Specimens were cut from the sheet for use as metallographic samples. For the thermal analysis a differential couple was used in conjunction with an X-Y recorder, the temperature of the specimen and the difference in ternperature between it and the standard nickel body were recorded simultaneously. Heating and cooling rates of 5°C per min were used. The sensitivity of the instrument was such that a difference in temperature between the specimen and standard equivalent to 0.1 mv produced a deflection of 1 in. on the recording chart. The chromel-alumel thermocouples were checked against a Bureau of Standards calibrated thermocouple. Melting-point determinations were made in a high vacuum induction furnace using an optical pyrometer. The pyrometer, calibrated against nickel, copper, and zirconium (iodide process) under near black body conditions, was focused on the base of a hole drilled in cylindrical samples. A North American Philips Geiger counter X-ray spectrometer was used for all diffraction studies. This instrument, in addition to supplying precise intensity measurements of planar reflections, has an added advantage in that metallographic specimens mounted in bakelite can be used directly, and this

Jan 1, 1953

By H. E. Wilborg, G. V. Henderson

This chapter deals with those sands employed by foundries for the manufacture of cores and molds used in the casting of such common metals as steel, gray iron, ductile iron, aluminum-based alloys, and copper-based alloys. Most metal is cast in "green sand" molds in which the sand mixture, consisting primarily of silica, clay, and water, forms a plastic material. This plastic material is rammed around a pattern in a split box called a flask, then the box is separated, the pattern is withdrawn, and the metal is poured. These green sand molds are broken apart when the metal has solidified. The sand is then remixed and a new mold made for the next casting. To a lesser extent silica sand is mixed with resins or oils and, after forming, the mixture is hardened by either heat or chemical reaction. In any case, the foundry mold or core is used just once before being broken up and remixed for manufacturing another core or mold. By far the greatest consumption in the foundry is of those types of sand high in silica, low in clay (under 0.5%), and occurring in numerous locations thoughout the United States. Consumption End Uses Foundry sands fall into four distinct categories: silica sand, lake sand, bank sand, and natural molding sand. Silica sand is a general term used to describe washed, graded, dried, and cooled clay-free sands which are found in many parts of the United States. They generally contain 90 to 100% silica but vary greatly in chemical analysis and grain structure. Lake sand is the sand dredged from Lake Michigan or dug from the dunes bordering that lake. Bank sand is composed primarily of silica grain but containing up to 5% clay. It is shipped in both the damp and dry state but the normal processing of bank sand consists only of drying and scalping. Occasionally two different grades of bank sand are blended prior to or during loading. Natural molding sand is a term used to describe a sand containing sufficient clay as mined to be suitable for molding purposes. Clay content may vary from 10 to 24% with the balance of the material consisting primarily of silica sand. These sands range in fineness from one peaked on the 20 mesh to one which contains more than 50% of the particles passing the 270 mesh. Lake sands are relatively coarse and are used in great quantities for the production of automotive castings. Bank sands and natural molding sands are gradually phasing out as the production of castings becomes more a science and less an art. The vast majority of foundry sands used today are those known as the silica sands and lake sands. Foundry sands are used in two basic ways. The majority are used in the green or uncured state with the balance used in the cured or set state. Green sand is grain bonded with clay and contains varying amounts of water to plasticize the clay in order to bond the grains together. Green sand is either naturally bonded or "synthetic" sand. The naturally bonded molding sands are generally found in the Hudson River Valley of New York State, Cumberland County in New Jersey, and in Tennessee and Mississippi. Synthetic sand is molding sand compounded in the individual foundry. It is made up primarily of graded silica sand, western or southern bentonite, water, and carbonaceous and/or cellulosic materials. Green sand is used primarily in making molds. The use of naturally bonded green sand has been declining for many years, primarily because naturally bonded sands are more difficult for the foundryman to find and control. Synthetic green sand, on the other hand, can be

Jan 1, 1983

By Ellis H. Gates

BENEFICIATION of the manganese oxide ores at Three Kids Mine near Henderson, Nev., has evolved over a period of years. Commercial application of the process is on a secure basis, and an effective working hypothesis has been formulated to help solve the problems encountered in flotation. An outstanding difference between the Manganese Inc. operation and other flotation processes is the necessity for high recovery of slime mineral values. Part of the manganese minerals in the Three Kids ore deposit occurs as primary slime or as minerals that are easily slimed by grinding. High recovery of this slime portion is essential to an economic overall manganese recovery. The aim of much of the research at Manganese Inc. was to recover these slimed and finely ground minerals by flotation. Early Agglomeration Processes: Tunbridge' in 1880, followed by Everson2 in 1886 and Cattermole" in 1904, discovered that under certain pulp conditions precious metals and sulfide minerals could be agglomerated if enough soap or oil were mixed into the pulp slurry. These agglomerated particles, Which under ideal conditions ranged from 1/16 to 1/4 in. diam, were recovered by screening, tabling, and hydraulic classification. Even flotation by air occluded in the agglomkrate particles by vigorous stirring was suggested. Cattermole nearly succeeded in getting his process into commercial operation, but it was finally abandoned, presumably because he could nat compete with the low reagent requirements of the new agitation froth process. Since Cattermole's time Christensen in 1921, Borcherdt4 in 1926, and Chapman and Littleford- in 1934 have attempted to apply the principles of agglomeration. In the light of current research at Manganese Inc. on conditioning of pulp at high energy input levels, it is interesting to note the variety of equipment such as tumbling mills, mixing drums, and shakers described by Borcherdt in his patent to produce the agglomerated particles. Ore Characteristics: Manganese in the Three Kids ore occurs as a 'complex mixture of manganese oxides commonly Known as wad. The manganese minerals have Been identified as psilorflelane, hollandite, coronadite, and pyrolusite with minor amdunts of rhodonite and rhodochrbsite. The ppincipal gangue miherals are quaktz, opal, kaolinite, montmoril-lonite, calcite, gypsum, fcelesitite, and barite. Most of the mangandse ore minerals are either porous and sponge-like in structure or soft clay-like masses composed of fine grained mineral particles approaching the size range of colloids. Consequently the ore minerals from the Three Kids mine have relatively large surface areas and high void content per unit weight. The specific area of various manganese ore samples measured at the California Research Corp. laboratories ranged from 32 to 58 sq m per g. The great surface area and high void content explains in part the unusually high reagent consumption required in the treatment of this ore. Current Milling Practice: At Henderson6 he ore is crushed to —1 in. and ground with rod mills in a closed circuit with spiral rake classifiers and cyclones. Sulfur dioxide solution is added to the pulp as it leaves the grinding circuit, immediately followed by addition of a reagent mixture of soap, oil, and wetting agent in the form of an emulsion. The reagents are initially well mixed into the pulp during their passage through centrifugal pumps to the conditioning equipment. All reagents are added prior to conditioning. The intense conditioning or mechanical stirring of the pulp, in which large amounts of power are consumed, is the principal difference between the flowsheet used at Manganese Inc. and a standard flotation circuit. As much as 38 kw-hr of energy per dry short ton of ore in a pulp containing 18 to 23 pct solids is used for conditioning. After conditioning, the pulp passes to a flotation circuit that consists of one roughing stage, a scav-

Jan 1, 1958

By W. A. Backofen, D. H. Avery, W. F. Hosford

Sheets of the magnesium alloys AZ31B, HK31A, and ZE10A in several different tempers were tested in tension and determinations were made of the ratio of width-to-thickness strain. A marked increase in the ratio with tensile straining and a dependence upon alloy and test direction are rationalized in terms of a balance between the amounts of basal and prism-plane slip. All such variations are related, in turn, to the prevailing crystallographic texture. Fracture appearance is explained on the basis of anisotropy in plastic flow, and implications for developing texture -hardening effects in these alloys are discussed. ThE crystallographic texture or preferred orientation of a given material is determined by details of processing history. Such texture is known to influence many aspects of material behavior, in particular both the yielding and strain-hardening characteristics which are of special interest in the present work. Traditionally, the resulting plastic anisotropy has not been regarded as especially desirable. Earing in drawn sheet is perhaps the most common example of an unwanted effect of texture. However, it has also been recognized that suitable textures may be usefully employed to improve drawability,1,2 as a specific example, and generally to control yielding resistance under combined-stress loading.374 Texture would seem to be a detail of structure not yet exploited to nearly the fullest extent. A convenient basis for characterizing anisotropy in plastic behavior is the ratio of width-to-thickness strains obtained in a tension test;5&apos;6 the parameter is frequently labeled "R" and its value is revealing with respect to the nature of the prevailing texture. R gives a useful measure of a material&apos;s "thinning resistance". For an isotropic material, R = 1. With R > 1 the increased through-thickness strength in a sheet means greater resistance to yielding under biaxial tension, or "texture hardening";3&apos;4 if R < 1 the result may be a "texture softening" under the same loading conditions.4 Most R data relate to steel sheets for deep-drawing applications. Values for steel and other materials of cubic structures are not often much greater than 1 and nearly constant with strain in testing.1,2,7,8 To explore the implications of plastic anisotropy further, it was felt that experiments with much more strongly textured materials would be useful, and this led to the choice of magnesium alloys. The "ideal" sheet texture for magnesium contains the (0001) plane in the rolling plane, which ought to lead to R values approaching infinity. However, departures from the ideal texture, the possibility of slip in non-close-packed directions, and deformation by twinning would all be expected to introduce some range of R. Accordingly, studies on these materials were undertaken. EXPERIMENTAL Alloys in sheet form, Table I, were selected to obtain a variation in crystallographic texture, in the expectation that this would be reflected in differences in plastic anisotropy. Pole figures constructed by the Schulz surface-reflection technique9 were provided with the experimental materials by the Dow Metal Products Co. Profiles of pole density along great circles through the rolling (0 deg) and transverse (90 deg) directions were prepared from the pole figures and are collected in Figs. 1 and 2; considerable departure from the "ideal" (0001) alignment in the rolling plane is evident, with the largest angular spread in both directions being found in the ZEl0 alloy. Results of tensile tests on full-thickness specimens of 6-in. gage length by 1/2-in. width are given in Fig. 3 as engineering stress-strain curves* in rolling and transverse directions. All tests but one were made at a constant drive rate of 0.02 in. per min, and the final values of percent elongation at fracture, over the initial 6-in. gage length, are noted at the ends of the curves; one test on ZE10A-

Jan 1, 1965

By J. Lohrenz, R. J. Francis, G. C. Clark

Compositional material balance methods have been extended to solution gas-gas cap-water drive reservoirs. Partial or complete pressure maintenance as well as reservoir repressuring by gas and/or water injection may be considered. Increrments of reservoir withdrawals and injections equivalent to a given time increment are used as the basic iterative step to allow the extension. An example field study shows how the reservoir volumes. extent of the water drive, and relative permeability ratio function may be estimated. Knowing these, the methods can be used to predict reservoir behavior. INTRODUCTION The compositional material balance is similar to conventional material balances in many aspects. The assumption of a pressure-homogenous reservoir with no transients is common to all conventional material balances1-1 although numerical methods are different. The compositional material balance also contains this assumption. Inclusion of phase equilibria directly in reservoir calculations is the key difference and improvement in the compositional material balance. A continuous account of the compositions of the reservoir fluids and effluents is determined. Calculations of fluid phases and properties can be based on these compositions. Excepting fluid phases and properties determined in this manner, the compositional material balance uses procedures exactly analogous to conventional methods. Brinkman and Weinaug5 and Jacoby and Berry6 have given compositional material balances for simple solution gas drive reservoirs; subsequently Jacoby and Berry&apos; extended their procedure to include pressure maintenance by gas injection at constant reservoir pressure. This paper extends compositional material balance techniques to a more general combination drive reservoir with various types of pressure maintenance operations. The procedure for this extended compositional material balance and an example of its field application are presented. PROCEDURE The numerical calculations of this compositional mate- rial balance are performed on a high-speed digital computer. The most comprehensive case the present compositional material balance program can handle is a solution gas-gas cap-water drive reservoir with (1) water production, (2) water influx, (3) separate or commingled production from the oil and gas zones, (4) any surface processing arrangement including LPG and gasoline production, and (5) gas injection into the gas and/or oil zones." This description of the procedure applies to this most comprehensive case. Appropriate deletions in the procedure can be made for more simple mechanisms. ASSUMPTIONS In common with conventional material balances, the compositional material balance makes the following assumptions: (1) the total reservoir is at a uniform pressure at a given time; (2) the volumetric ratio of gas to liquid withdrawal at reservoir conditions is directly proportional to their mobilities; and (3) instead of assuming a pressure-dependent total gas-oil equilibrium, the cornpbsitional material balance makes a sianificantly different and more rigorous assumption as follows. Thermodynamic equilibrium exists for each component in the liquid-gas mixtures in the reservoir and in surface processing. These three assumptions are fundamental in the compositional material balance procedure. Other assumptions involve arbitrary simplifications of the reservoir mechanisms. This compositional material balance uses the following simplifying assumptions: (1) no bulk mixing occurs between the gas and oil zone; (2) total mixing occurs between any injected gas and the contents of the injection zone; (3) no in situ hydrocarbon liquid is produced from the gas zone; (4) no reservoir gas is retained behind any net bottom-water influx; (5) the residual saturation of hydrocarbon liquid at reservoir conditions behind any net bottom-water influx is constant; and (6) fluids retained behind any net bottom-water influx exert no further influence on the reservoir. These six assumptions are not fundamental. Modifications of the present procedure can be made for different assumptions of the reservoir mechanisms. THE TIME INCREMENT Previous compositional material balances have used a pressure increment for simple solution gas drive reservoirs"" and an increment of injected gas for pressure maintenance.&apos; These increments are suitable for these simple cases. They are, however, inadequate for reservoirs with time dependent drive mechanisms including water drive. A time increment removes this inadequacy and is

By I. R. Dunlap, R. F. Burdyn, F. D. Patchen

The composition and properties of a new type of cementing mixture are discussed. In these compositions, API Class A or C cements are added to n stable water-in-oil emulsion instead of the crsual water. The cement disperses in the oil phase and remains out of contact with the water under normal conditions of mixing and storage. At higher temperatcrres, such as those encountered down-hole during placement, the emulsion breaks and cement hydration can then proceed. An extremely low filtration rate is obtained; the major part of the filtrate is oil. Thickening times of the mixture may be increased to meet the 18,000-ft casing cementing schedule by varying the amount of emzilsifier. As in conventional Portland cement mixtures, high-temperature strength retrogression can be overcome by addition of silica flour. Results of several field app1ication.r show that mixing presents no diffculty if emulsion blenders are used and the emulsion is prepared beforehand. INTRODUCTION Water-in-oil emulsions., in which oil is the continuous or external phase and in which water exists as discrete droplets, have for some time been used successfully in drilling muds to reduce filtration loss.1,2 Applied to cement slurries, the same results are obtained; i. e., the fluid-loss is greatly reduced. In addition, thickening times may be extended, lower densities and strengths obtained, and water-base borehole fluids more easily displaced without contamination of the cement. A low filtration rate is often a desirable property in oil well cements since loss of fluid increases placement difficulties and may also cause damage to water-sensitive producing formations.&apos; In the casing cementing operation where the cement slurry is pumped into the narrow annulus between open hole and casing, rapid loss of fluid to a porous formation can cause the slurry to thicken and plug the annulus before the desired fill is obtained. Where a casing or a liner is cemented against a productive formation and the well completed through perforations, the fluid lost between the time the cement first contacts the formation and the time a set is obtained may invade the zone past the depth of the perforations. If the sand contains a material which will swell upon contact with cement filtrate, permanent damage may result. Previous methods for reducing the fluid-loss of cements have employed bentonite4 as an additive, usually with a lignosulfonate as a dispersant, or a derivative of some naturally occurring polymeric material such as cellulose ether." Oil emulsion cements have also been proposedv or fluid-loss reduction, but these have been of the oil-in-water type. Bentonite cements have been used most widely and have been successful in reducing incidence of premature setting of cement attributable to loss of water by filtration. It is the purpose of this paper to describe preparation and properties of a water-in-oil emulsion cement and to relate procedures followed and results obtained in several field applications. DESCRIPTION OF SYSTEM AND MECHANISMS A water-in-oil emulsion cement is prepared by adding an API Class A or C cement to a stable water-in-oil emulsion. Fig. 1 is a photomicrograph of this emulsion before addition of cement. Here the droplets are water and the surrounding medium is diesel oil. High emulsion stability is indicated by the small droplet size [1-5 microns], and by their uniformity.&apos; To form a stable water-in-oil emulsion as illustrated, several conditions must be met. A predominantly hydrophobic emulsifier must be present in sufficient concentration to produce a strong interfacial film; initially, the phase volume ratio (the water-to-oil ratio) must be low;