Search Documents

By R. B. Mears, G. F. Sagar, R. H. Brown

There are well recognized procedures for determining the various tensile, fatigue, and other mechanical properties of the common structural materials. This makes it possible for engineers to design structures of various materials which have adequate initial strength to stand the stresses to which they are subjected in service. There is also considerable general information about protective measures suitable for protecting the usual structural materials from the effects of ordinary environments. However, often insufficient quantitative information is available on the combined effects of stress and corrosion to permit the designer satisfactorily to appraise the structure from the stress-corrosion standpoint. This situation is further complicated by the fact that the stresses causing stress¬corrosion failures are usually not the design stresses but rather the residual forming and assembly stresses which are generally of unknown magnitudes. Thus, tests which will rapidly evaluate the susceptibility of materials to stress-cor¬rosion failures are extremely useful. Of particular value are tests which can be applied to built-up structures as well as to simple specimens, since, as mentioned above, residual stresses often are caused by fabricating procedures and assembly operations. The present paper contains

Jan 1, 1945

By G. F. Sager, B. J. Nelson

Magnesium alloy forgings offer higher and more uniform mechanical properties than heat treated magnesium alloy castings and are used principally for light weight parts that may be stressed in fatigue or subject to impact loads, or where space limitations do not permit the use of the necessarily bulkier magnesium alloy castings. Compositions and Properties of Magnesium Forging Alloys The nominal compositions and properties of the principal commercial magnesium forging alloys are given in Table 1. The two that are most commonly used are AMC58S and AM65S. The former has the highest strength and is, therefore, employed for heavy duty applications. However, the forging of this alloy and of AMC57S ordinarily requires the use of slow speed hydraulic presses. The forging alloy AM65S combines good, although somewhat lower, mechanical properties with excellent forging characteristics. This alloy can be forged on hammers, upsetters, rolls, and mechanical presses, as well as on hydraulic presses. These characteristics make it particularly useful for many applications. Manganese Segregation in AM65S The alloy AM65S contains 5 pct tin, 3 1/2 pct aluminum, and a small amount of manganese, the manganese being added to insure satisfactory resistance to corrosion. Some manganese segregation was occasionally encountered in this alloy. In many applications, such segregation is of no particular consequence, but when forgings are acid dipped prior to the application of various chemical coatings, the segregated particles of manganese constituent may stand in relief. The resultant surface roughening may impair appearance and is undesirable in forgings employed in the textile industry, where very smooth surfaces are essential to avoid the catching and breaking of fine threads. An effort was therefore made to determine the cause of manganese segregation in this alloy and find a method for its elimination. Radiographic examination of a series of cast ingot sections and extruded samples of the AM65S type having manganese contents ranging from zero to about 0.7 pct revealed no appreciable manganese segregation when the manganese was less than about 0.4 pct. A small amount was observed with a manganese content of 0.46 pct and considerable with manganese contents of 0.6 pct or higher. Attempts to eliminate the manganese segregation by variations in the melting and casting conditions were unsuccessful and it soon became apparent that the trouble was attributable to the fact that the manganese contents that caused segregation were in excess of the amounts that would remain in solution at temperatures encountered in the melting and/or casting operations prior to the complete solidification of the ingots. A knowledge of the amounts of manganese that would be soluble in molten alloys of the AM65S type at various temperatures was obviously desirable. The liquid solubilities of manganese in binary Mg-Mn alloys and in Mg-Al-Mn and Mg-Zn-Mn alloys have been determined by Tiner and others,* but no data on the solubility of manganese in molten magnesium alloys containing tin and aluminum are given in the literature. For this reason, an investigation to determine the solubility of manganese in a magnesium alloy containing 5 pct tin and 3.5 pct aluminum (AM65S type) was undertaken.

Jan 1, 1950

By J. A. Richardson

J. A. RICHARDSON[t]-Mr. Stuckey's account of the geology of the kaolins of North Carolina suggests that they exhibit some features similar to those of the Malay Peninsula. About one half of British Malaya (some 26,000 square miles) is occupied at the surface by igneous rocks, of which granite and its associated derivatives constitute fully 90 pct. The average granite is a biotic variety. It is predominantly potassic but carries, in addition, notable amounts of soda and lime so that albite and albiteoligoclase are generally common constituents of the rock. The minor derivatives from granite "magma" likewise include potassic and sodi-potassic members. Decomposition of the granitic rocks has led to the formation of kaolin in many localities, but, in general, the deposits are rather small and, at present, none is exploited commercially. True primary or residual kaolins (as defined by Stuckey; p. 48 Vol. 173, p. 2 TP 2219) have been developed from feldspar veins, pegmatites and from other granitic differentiates which cut through the larger masses of granite; they are usually small and narrow. Kaolin has been derived from aplite, quartz porphyry, quartz micro-porphyry, felsites and microgranites belonging to a complex known as the Chegar Perah-Pulai intrusion in northwest Pahang and southwest Kelantan. The bulk of the component rocks has been more or less strongly sheared. Kaolin-like end products have been formed from both sheared and nonsheared varieties. Kaolin has been formed also by the complete breakdown of trondjemite flanking the northwestern and western margins of the complex Bukit Ranjut syenite intrusion in northwest Pahang. These trondjemites range in composition from essentially quartz-free albiteplagioclasites to quartz-free microcline rocks; they are, in effect, the syenitic homologues of white sodic and potassic granite-aplites. The granites in Malaya have generally undergone more or less severe surficial weathering leading to the production of a spongy and rather cellular or a soft "mealy" material (sandy clay) down to depths of about 100 ft; in places the granite is strongly decomposed down to 150 ft. There has occurred, therefore, widespread partial kaolinization, but, in general, no extensive deposits of good quality kaolin seem to have been formed by these processes of decay. Frequently, the katamorphic processes of desilicification have advanced beyond the production of kaolin towards the formation of lateritic end products. The more important Malayan kaoiins seem to be confined to the western alluvial plains, particularly in areas either where granite crops out at surface, or where it forms the bedrock of the alluvium. There are numerous excellent examples around Gopeng and elsewhere in the Kinta Valley of Perak. Such kaolins belong to Stuckey's groups of secondary deposits, and, like them, these also may be bedded. Field observations have established the existence of what for want of a better name is referred to by the Malayan Geological Survey as "granite wash." It is believed that granite, undergoing extensive deeply penetrative and probably rather rapid destruction under humid tropical weathering (temperature around 90°F; rainfall about 100 in. per annum; high humidity) "flowed," was moved by "creep" and, in addition, probably slumped in large waterlogged masses of sandy clay from topographic salients onto the adjacent flats. Either during this period of transmigration or later when the sludged granite detritus, after having more or less come to rest, was attacked by flowing water, differential sorting and erosion took place with the result that the resorted debris was moved and later deposited as bedded alluvium. In this way, banded "granite wash" was produced comprising alternating bands of clayey sand (resorted granite sludge) and white

Jan 1, 1947

By J. S. Lasater

Resu1ts of experinmental measurernents of heat capacities and thermal conductivities of some typical porous rocks are presented. Measured heat capacities agree closely with va1ues calculated front known chenlical . compositions of the rocks. On the basis of this agreement, heat capacitir.7 of fluid-satttrated rocks were calc~ililted. Therrnal conductivities of the rock samples were measured under varioits conditions of fluid saturation. From these data therrnal dif-fvsivities were calculated. A significant variation of thermal diflusivity with trnlperature is indicated. Knowledge of the thermal characteristics of fluid-bearing porous rocks has become increasingly important with the development of thermal oil-recovery processes. Reliable thermal data for petroleum reservoir rocks are not available and approximate values are generally assumed for reservoir calculations. 'The effects of temperature, pressure and fluid saturation on thermal properties of porous rocks have not been carefully studied. The purpose of the present work was to measure and report the thermal characteristics of some typical porous rocks. A group of eight sedimentary rock samples, including limestone, shale, sandstone and silt-stone, was selected for the study. Properties reported include heat capacities, thermal conductivities and thermal diffusivities. The effect of fluid saturation on these properties was also considered. Determinations of thermal properties require precise measurements which are time consuming and difficult to reduce to a routine basis. Methods have not been developed for measurement of thermal proper-ties under conditions of pressure, temperature, and fluid saturation, which may be encountered in thermal recovery processes. As one approach to these problems, some preliminary work on methods of estimating thermal properties from other more readily measurable characteristics of the rock-fluid system is reported. The samples selected for the studies were oilfield cores from within, or closely associated with oil-productive zones. Descriptions of individual samples are given in Table 1. Clay minerals present in the samples were determined by differential thermal analysis (DTA). Quartz content was estimated from DTA cooling curves. For all but the thermal conductivity tests, a representative 200-gm sample of each core was disaggregated, thoroughly extracted in diox-ane and oven dried at 100°C. The cleaned and dried sample was care- fully split into appropriate portions for the several tests. Chemical analyses of the samples were obtained to permit calculations of heat capacities by methods which are outlined later. Resuits of chenlical analyses are given in Table 2. Heat contents of the test samples were measured by a Runsen-type calorimeter. The heat content of the unknown sample is measured relative to the known heat content of platinum. The apparatus is referred to as a relative error type because of the comparative measurements, and has the advantage of canceling systematic errors. Experimental results are reproducible within 0.5 per cent. A temperature base of 298.16 K is taken for heat content measurements. Measurements were made at five temperatures (260, 440, 620, 800 and 980° F). It was necessary to preheal the sample above the maximum experimental temperature to eliminate volatile constituents. Assuming the weight loss on pre-heat, ing was mostly water, a correction to the observed heat content was made to account for the water originally present in the sample. This latter procedure was followed in the determination of calculated heat contents as will be described later. The apparatus and the method of measure-

By William P. Roe, James F. Ellis, W. P. Fishel

This paper reports the distribution of sulphur between iron and titanium in Fe-Ti-S alloys and in Fe-Ti-C-S alloys. The compound TiS was found, which exists as a separate phase at temperatures below 1200°C. Titanium in steels reacts with sulphur in preference to carbon. THE general relationship between sulphides and oxides suggests that titanium should form a sulphide having properties similar to those of titanium oxide. Specifically, titanium should form a sulphide having a high melting point, indicating a stable compound of low solubility in iron. In order for titanium to function as a desulphurizer or sulphur-fixing agent, it must form a stable sulphide. In order for titanium to be useful in steels as a sulphur-fixing agent, it must react with sulphur in preference to carbon; and to prevent red shortness, the sulphide formed must have solubility characteristics such that grain-boundary precipitation of a low melting phase be prevented. The terms desulphurizer and sulphur-fixing agent when used in this paper mean that titanium effectively ties up the sulphur as a stable sulphide of titanium and prevents the formation of FeS. The partition of sulphur between iron and titanium was studied first in a series of Fe-Ti-S alloys with carbon absent, and then in similar alloys with carbon present. It has been established1 a that titanium forms in Fe-Ti-S alloys a sulphide of undetermined composition which can be identified microscopically, and that the titanium-sulphur compound does not respond to sulphur printing. It has been suggested" that titanium acts as a sulphur-fixing agent, although little proof has been given. A report% f The Advisory Committee on Metals and Minerals summarizes the existing knowledge concerning substitutes for manganese in steels. Distribution of Sulphur Between lron and Titanium with Carbon Absent The alloys for this investigation were made by -melting Armco iron, metallic titanium, and iron sulphide in alundum crucibles in an induction furnace. The titanium was added after the other ingredients had melted. In these alloys it is recognized that some TiO, is present, since the melts were made in the air and since no other deoxidizing agent was used; therefore, some of the titanium was not available for union with sulphur. Thirteen ingots were made. Ingots 2 to 8 were cast in baked-sand molds; ingots 12 and 13 were cast in metal molds; and ingot 9 was allowed to cool in the crucible in which it was melted. All ingots were annealed at 900°C for 3 hr and were cooled slowly in the furnace. Subsequent information indicates that this anneal had no effect upon the titanium sulphide particle size, since the sulphide does not go into solution at this temperature. The ingots as-cast were approximately 8 in. long and % in. diam. The compositions of the eight ingots and the results of the partition of sulphur are recorded in Table I. Total titanium and total sulphur were determined by standard gravimetric methods. Sulphur, as iron sulphide, was determined by the evolution method. Boiling HC1 (1:4) liberates the sulphur from iron sulphide, but leaves the titanium sulphide practically undecomposed. A complete separation of titanium sulphide and iron sulphide cannot be made by digesting these compounds in dilute HC1 since titanium sulphide was found to dissolve slowly. The amount of titanium sulphide decomposed will depend upon the time in contact with the acid and upon the particle size of the sulphide. The point

Jan 1, 1952

By Nick Holonyak

Halogen vapor-transport synthesis of Ga(As,-,Px) and its preparation into laser junctions are described. Electrical and optical properties of Ga(As,-,PX) laser junctions are discussed. The present limitations in these properties are related to material proble?vzs and the very early state of development of Ga(As,-,PX), and are discussed in this context. Inhonzogeneity problems, fluctuation of As :P ratio, and problems with deep-level contaminants are described and related to Ga(As,-,PX) junction performance. Laser junctions are demonstrated which operate to wavelengths as short as 6470 A (77°K). The prospect that Ga(As,-,P,) will operate to wavelengths perhaps 100A shorter is mentioned. IN this paper we wish to describe some of the more important features of almost 1 year of experience in the preparation and properties of Ga(As,-,P,) p-n junction lasers. Because much data so far available are far from complete, some of the results still must be considered tentative and subject to correction and revision as work on Ga(As,-,P,) crystal problems progresses. Although the electrical, optical, and device properties of Ga(As,-,P,) junction lasers are understandably of considerable interest, the work to date points out that by far the most serious problems extant and those deserving first attention are problems involving the growth, doping, and perfection of Ga(As,-,P,) crystals. One of the most formidable of these is to grow Ga(As,-,P,) sufficiently free of deep levels, either due to contaminants or to structural imperfections, to allow fabrication of laser p-n junctions which can be cooled and not suffer from "freeze-out" of carriers on deep levels (and consequent double-injection behavior). In addition to the problems of growing crystals adequately free of deep levels and generally of the highest perfection, so that the best possible laser junctions can be realized, the further goal remains of increasing the phosphorus content well beyond 40 pct in an attempt to determine the practical lower wavelength limits of laser action in the Ga(As,-,P,) system. Even though the laser junctions prepared in Ga(As,-,P,) are of importance in their own right, we have considered them at this point mainly a means to study the growth and crystal problems of the material. It can be concluded that the laser junctions now available are almost completely limited by the purity and structural deficiencies of Ga(As,-,P,) crystals, and cannot be fairly compared with, for example, GaAs p-n junction lasers until Ga(As,-,P,) crystal growth has been more extensively developed. The basis for the statements above will become evident in the following sections which describe Ga(As,-,P,) crystal and junction preparation, and laser-junction properties. G(As,-,P,) CRYSTAL GROWTH As previously reported,2 we have found it convenient to employ the halogen vapor-transport process3 for synthesizing Ga(As,-,P,) crystals for use in laser junctions. Commercially available GaAs and Gap, separately prepared by halogen vapor tranport, are sealed in the desired ratio in a quartz vessel with a quantity of column-VI donor and a small quantity of metal halide which supplies the halogen for transport. The sealed ampoule, as shown in Fig. 1, is heated at a temperature in the range from 1025" to 1100°C at the position of the source GaAs and Gap. The GaAs and Gap are simultaneously vapor-transported and deposited as Ga(As,-,P,) at one end of the ampoule

Jan 1, 1964

By W. A. Stickney, J. W. Town

Tests demonstrated that aqueous solutions of sodiu~n sulfide would dissolve over 95 pct of the cinnabal- in 5 pct Hg flrotation concentrates and 60 to 90 pct of the cinnabav in low-grade ol-es. Double-leach tests showed that potassiutn sulfide would dissolve 90 pct of the avsenic sulfide in Hg-As satnples and only 1 to 10 pct of the Hg; the sodium sulfide would then dissolve 80 to 90 pct of the rernaining Hg and 30 to 70 pct of the vemaining As. 1 HIS paper describes the extraction, by alkaline sulfide solutions, of mercury from cinnabar-bear ing ores and flotation concentrates. Leaching time and solution temperature had minor effects on mercury extraction when compared to the effects of reagent quantity and ore type and grade. Cinnabar, although readily soluble in sodium sulfide, was only partially soluble in potassium sulfide and essentially insoluble in ammonium sulfide. A double leach process was developed to extract selectively the arsenic from Hg-As products with K2S and to treat the residue with sodium sulfide-hydroxide solutions to extract the mercury.' Mercury was then recovered from the pregnant solutions either by precipitation with metallic aluminum or by electrodeposition. The solubility of HgS in alkaline sulfide solutions was first reported by Volhard in 1878.' The first reported commercial application was made in 1915 when Thornhill applied the method to the treatment of an amalgamation tailing.3 Mullhollen, in 1911. described the chemical reaction of HgS with Na,S and alkaline hydrate to be:4 Most investigators have reported using a 4-pct sodium sulfide and a 1-pct sodium hydroxide soluti~n.3-4 An increase in temperature or excessive dilution of the solution causes the reaction to be reversed. Church Holmes described a similar process used for the extraction of antimony from silver concentrates at the Sunshine Mining Company's mill at Kellogg. Idaho.5 More recently. Erspamer and Wells reported the results of leaching studies on a Hg-Sb ore from Alaska.6 EXPERIMENTAL PROCEDURE Leaching tests were made on samples of mercury ore from eight deposits in Oregon, Washington, and Idaho. In addition. tests were made on flotation concentrates from seven of the samples as well as a flotation concentrate from an operating mill. Since previous investigators reported reagent requirements greatly in excess of that required by the equation HgS + Na2S = HgS . Na2S, initial studies were made on chemically pure HgS. Results showed that the reaction actually required about 1 g of Na,S per g of HgS in an aqueous solution rather than 0.338 g of Na,S as indicated by the equation. To check further the matter of reagent requirements, Na2S and HgS were mixed together in equal mole ratios. Water was then added, a drop at a time, until the components reacted; X-ray diffraction analyses showed no HgS nor Na,S present. The yellow hydrate compound which formed would not redissolve until about three additional mole equivalents of Na,S were added to the solution. This indicated that a stable solution would require at least 4 moles of Na2S for each mole of HgS. While these implications may be valid for pure HgS, the possibility of entirely different results caused by the existence of other elements present in ores and concentrates was recognized. Consequently, experiments of the same order were made on samples of a flotation concentrate from a producing mill. The concentrate, containing about 18 pct

Jan 1, 1962

By K. K. Kershner, W. A. Calhoun, C. W. Funk

Future resources of aluminum may require the utilization of low grade ores to provide a more permanent protection for the nation. Aluminum minerals such as cloy, shale, and high iron laterites may become important sources. An evaluation of reserves is given. New laboratory results are reported on the Vereinigte desilication process. THIS report on future resources of aluminum metal emphasizes the necessity for investigating utilization of low grade potential ores to provide more permanent protection for the nation. Partial or complete interruption of the importation of high grade aluminum ores must be given consideration. Ultimately, aluminum minerals such as clay, shale, and high iron laterites may become the principal sources of aluminum. The development of extractive processes for treating these low grade materials is a step in long-range national preparedness that should receive more attention. In formulating such processes, the application of beneficiation methods for the purpose of classifying the several types of minerals before subjecting each type to the more expensive extractive procedures should be considered, and a careful survey of the basic factors of power sources, transportation facilities, and sources of raw material should be made. Domestic Bauxite Resources Of the domestic supply of current, treatable-grade bauxite, 95 pct comes from Arkansas. The present reserve of Arkansas bauxite suitable for metal production, including abrasive-grade, Bayer-grade, and modified Bayer-grade ores, is 34,000,000 tons. The total reserve of bauxite of all grades is approximately 75,000,000 tons. Reserves are estimated on a mined and dried basis. Data available to the Bureau of Mines in 1948 to 1949 were used in preparing Table I, which shows a breakdown by grades of bauxite for about a half of the reserves of the state. The modified Bayer ore, 10,555,500 long dry tons, is based on a cutoff of 8 to 15 pct silica. The sub- marginal 10,074,700 long dry tons is assumed to contain more than 40 pct gibbsite, more than 15 pct silica, and less than 32 pct available alumina. A considerable amount of this low grade material was consumed in 1949 and 1950. Additional tonnages of bauxitic and kaolinitic clays are indicated by the Bureau of Mines drilling project.' Applying a 50 pct factor to arrive at long tons mined and dried, the results of this project are approximately 31,500,000 tons kaolinitic clay at +35 pct Al²O3 and 11,800,000 tons kaolinitic clay at 20 to 35 pct A1,0,. Total reserves of kaolinitic clays are probably quite extensive—several times the reserves shown in the Bureau's work. Total reserves of bauxitic and high iron clays from the drilling program and previously established figures are 63,980,000 tons. The mineral dressing methods,' the lime-sinter process, he lime-sinter modification of the Pederson process," the lime-soda sinter process,"-' and the Alcoa combination processa. have been described in the literature and will not be elaborated upon here. The less familiar Vereinigte Aluminium-Werke process used by the Germans during World War 11 may require some amplification. It was used to bene-ficiate boehmite ores containing 12 to 18 pct silica for a feed to the European Bayer process. Ore was

Jan 1, 1952

By Albert S. Trube

Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of reservoir fluids well in advance of more accurate laboratory data. One such factor is the isothermal coefficient of expansion of an undersaturated hydrocarbon liquid which may be contained in a particular reservoir. This coefficient, or liquid "compressibility", has often been assumed to be relatively insensitive and nearly constant. Although this assumption may be nearly correct in the case of high specific gravity liquids, it cannot apply in the case of medium to low specific gravity liquids. Any treatment of the nature of liquid compressibilities must give consideration to the variable nature of the isothermal expansion coefficient and the fact that it can be both pressure sensitive and temperature sensitive. The isothermal coefficient of expansion, or compressibility, of a substance is defined as -c = 1/V (?V/?p)T......(1) The value of Eq. 1 may be approximated for a finite pressure change by using the well-known relation, c = V1 - V1/Ve (p2-p1), ........(2) in which p1 > p1 and V2 > V2 and V1 + V2/2. The instantaneous compressibility may also be estimated from the slope of a curve on which log V is plotted vs pa. In this instance, it has been shown that c = In V1/V2/p2-p1 ...........(3) Eq. 3 may be used for variable compressibilities by plot-ting V vs p on semi-log paper. In this case, the instan-taneous or point compressibility is c = 2.303 m.......... . (4) in which m is the slope of the curve at a point in log cycles per psi. ISOTHERMAL COMPRESSIBILITY OF UNDERSATURATED LIQUID In the case of gases, the compressibility has been defined by Muskat' and others as Co = 1/p - ?z/z?p ..........(5) This was later generalized through application of the theorem of corresponding states' to co = 1/pr - (?z/z?pr) T8 ........(6) in which c, is defined as the pseudo-reduced compres-sibility and is numerically equal to (c.p,) and the sign is arbitrarily changed for mathematical convenience. Eq. 6 is general and applies to gases and liquids. In the case of liquids, c. = c1,pe, but if Eq. 6 is used, values of z and ?z/?p, must be determined for the liquid in question. The difficulty of obtaining accurate values of ?z/?p,, particularly in the region where T, is approaching 1.00, was pointed out in the previous paper'. This method of approach is unreliable for extension into computations of liquid compressibilities. On the other hand, c, can also be defined as follows: - Cr = 1/Vr (?Vr/?pr) Tr ......(7) and from which, Cr = 1/pr (?pr/?pr) Tr .....(8) In accordance with the theorem of corresponding states, Vr = V/Vr, p, = p/pr and pr = p/pr. Ref. 2 pro-vides an excellent source of reduced density, reduced pressure and reduced temperature data for a wide variety of fluids. For the purpose of this investigation, the set of fluids2 having ze = 0.27 was chosen because it in-cludes most of the heavier hydrocarbons usually found in those complex mixtures loosely defined as "reservoir oils". Data on undersaturated liquids in Ref. 2 were rearranged to conform with Eq. 8. To simplify the computation of cr, the isothermal p, data were plotted vs the log of pr, in which case for any straight line or tangent cr = 1/M pr pr .....(9)

Jan 1, 1958

By O. J. Neslage, R. W. Jenkins

MINE operators today are paying increased attention to the mechanization of drilling operations as an important factor in increasing efficiency and decreasing costs. Recent progress in the design of drill jibs for mounting on drill carriages, or jumbos, has done much to advance the mechanization of mining methods. This progress has introduced new opportunities in the application of "jib jumbos" that are worth serious consideration. An attempt will be made here to classify the various types of jumbos and drill mountings available for level development and flat stope work, t6 indicate applications, and to measure their effectiveness in relation to their cost. The data here are based on a wide variety of field usage, and are offered only to point up, in a general way, the relative efficiency in proportion to cost. It should be remembered that any contemplated jumbo installation must be studied to determine what type of installation is most suitable, considering ground conditions, loading, timbering and haulage equipment, service available, and attitude of manpower. Early Drill Carriages: The advantages of some sort of a drill carriage were recognized at the time rock drills were introduced. In drift or heading operations where a fairly standard drill round and cross section were anticipated, as well as in flat bedded deposits where standard slabbing rounds were used, track and crawler-mounted drills found an early application. These first drill jumbos were little more than drill carriers, designed locally and manufactured with materials at hand. Of comparatively simple construction, function, and low capital cost, they usually consisted of a hinged column which supported one or more drills on arms or universal bars. When the column was pivoted vertically, the drills were moved into position. Screw jack extensions reached from the column to the roof and floor to hold the drill rigid. In some cases, particularly in tunnel jumbos, enough weight was carried that rail clamps or roof jacks were sufficient. Many of these column and arm-type jumbos, usually equipped with air and water manifolds, steel racks, and staging for drillers, are still in use today. Some have employed air or hydraulic extensions for securing the columns. They offer the equip-saving advantage of having all the necessary out, ment together, and they un be moved i and t. set up and torn down as a unit. Boom-type Jumbos: When the advantages of to column-type jumbo were seen, operators could to realize the further gains possible. More time could be saved with mechanical assistance to position api drill vertically. A rack on the column and a pinion on the arm for raising and lowering the drill in the manner of a quarry bar were tried with some success. The most outstanding solution to the vertical handling problem was reached with the boom-type of jumbo. Here two or more machines were mounted on a cross arm at the end of a boom that was pivoted at the rear of the track. This was raised and lowered by various mechanical aids. Occasionally air or hydraulic power was used. Nearly all of today's wagon drills use this boom-type principle. Boom jumbos represent a savings in time and physical effort expended in raising and lowering the drills. The boom must be balanced by the roof of the truck which is secured by rail clamps or type jacks. The most successful application of areawhere this of jumbo has been in the Tri-State area where multiple long-feed machines are used on caterpillar-mounted, boom-type jumbos for slabbing

Jan 1, 1951

By S. Shapiro, G. Krauss

RECENT investigations1 3 of the products of marten-sitic transformation in Fe-Ni and Fe-Ni-C alloys have made use of light microscopy to describe mar-tensitic fine structure. The application of conventional metallographic techniques to this problem was possible because of the similarity of distributions of parallel striations developed by etching polished surfaces to distributions of transformation twins which are positively identified in thin films by transmission electron microscopy. The surface striations frequently are not well-defined, and could also be due to, for example, rows of etch pits which are not resolved by the light microscope. This note describes the etching effects revealed by examination of surface replicas of mar-tensite in the electron microscope. The application of a replica technique both extends the observations of fine structure made with the light microscope and allows the results of conventional metallography to be used with more confidence. Samples of an Fe-33 wt pct Ni alloy were used for this study because of the detailed knowledge of the fine structure of martensite which has been developed'-4 for alloys of about this composition. Samples transformed to martensite at -120°C, and transformed samples heated to 340°C to effect a small amount of reversal of martensite to austenite, were examined. Surfaces were first prepared for replication by elec-tropolishing in a chromium oxide-acetic acid electrolyte at a current density of 0.1 amp per sq cm and a temperature of 15°C or a perchloric acid-acetic acid electrolyte at a current density of approximately 2 amps per sq cm and a temperature of 15°C. The polished surfaces were then etched for 4 to 7 sec by immersion in a solution of equal parts HC1, HNO,, and H20. Application of the etchant for this period of time produced discrete attack of certain features without loss of resolution due to overlapping of areas most susceptible to etching. The etched surfaces were replicated by 1) preshadowing with Pt-Pd alloy at an angle of 20 to 30 deg, 2) depositing a thin carbon film, and 3) stripping the film and shadowing material by immersion in a 5 pct nital solution. Two types of etching effects were observed by examination of the surface replicas in the electron microscope: l) continuous striations centered at the bottom of long grooves or the tops of pyramidal elevations on the sample surface, and 2) high densities of fine etch pits. Examples of both types of features are shown in Figs. 1 to 4. The striations are in each case continuous and have the same characteristic configurations as do transformation twins in martensite. Fig. 1 shows that the density of grooves decreases toward the edge of a martensite plate and Fig. 2 shows a region where the striations are of varying length. Similar examples of transformation twin arrangements determined by transmission electron microscopy of thinned foils of martensite have been shown in the literature,'~ and, based on these similarities, the striations and their associated grooves or mounds are considered to be evidence for the presence of transformation twins. The transf~rmation twins in martensite are on the order of l00 A thick, much too fine for resolution by the light microscope. It appears that orientation-dependent etching of the matrix martensite about the twins results in grooves or surface elevations which

Jan 1, 1967

By E. F. Sumner, C. K. Eilerts

A partial differential equation was developed and programmed to compute the cumulation and flow of the liquid phase of a gas-condensate fluid. It was found that such cumulation near the wellbore may attain saturations permitting liquid flow within periods of the order of 1 day. The radius at which this saturation obtains advances toward the external reservoir boundary with continued recovery, although it may move only 2 to 5 percent of that distance during the productive life of the well. This relatively high saturation can cause a serious dimunition in delivery capacity. The pressure dilferential required for flow of gas through a formation with such saturation may be as much as three times greater than the corresponding differential in a formation where saturation is less than 2 percent. Because of the radial geometry, total reservoir pressure differential required for flow with a zone of relatively high liquid saturation about the well was indicated to be two to three times greater than without the saturation. INTRODUCTION A computing program developed by the authors 1 to integrate the partial differential equation for transient radial flow of gas-condensate fluids required a prevalued function, W(Po) = kD(p0)/M(p0)z0(Po).......(1) related to cumulation of condensate in pores of the reservoir as pressure declines. Methods were available for relating mobility to saturation, saturation to liquid-vapor volume ratio, liquid-vapor volume ratio to pressure and, hence, mobility to pressure to obtain W(pD). However, certain assumptions had to be made in advance of program execution concerning movement of the liquid phase and change in radial distribution of liquid saturation as recovery progressed. Because reservoir fluid mobility and related pressure gradients are markedly dependent on liquid saturation, it was desirable to eliminate the necessity for these assumptions and in this respect improve the reliability of a result obtained by integration. Experimental research was begun to determine the relationship of variables that control the reservoir flow of low liquid-vapor ratio fluids. With the porous medium partly saturated, permeability to a two-phase flowing fluid could not be measured because the viscosity was unknown. Viscosity could not be measured without knowing permeability of the liquid-containing medium; but mobility, the ratio of permeability to viscosity, was measurable. This property, and liquid-vapor volume ratio of the flowing phases, have values determined by nature of the fluid and porous medium and, in addition, were found to be pressure, velocity and saturation dependent. A program developed by Kniazeff and Naville 2 for computing multicom-ponent, two-phase flow used polynomials to represent saturation dependence of permeabilities for gas and for liquid phases, and an effluent viscosity constant under reservoir conditions. The authors developed a program based on a partial differential equation of similar mass balance origin but designed to represent distribution of an unlimited number of components between gas and liquid phases utilizing the experimental information available as to variable dependence. Attention was given to liquid-vapor volume ratio of the flowing phases, a property which is essential as a liquid saturation boundary condition. A program for computing implicitly saturation increase at uniform intervals along the drainage radius was combined with an existing program for calculating pressures, and the two were used alternately in an iterative solution for both saturations and pressures. The function W(pD) needed for calculating pressures was replaced by the ratio of mobility to compressibility factor. BASIC EQUATIONS The partial differential equation for calculating

By N. Marusov, D. K. Lowe, J. C. Karp

This paper considers, from an engineering viewpoint, several factors involved in creating, designing and locating horizontal barriers for controlling water coning. This is an effort to consolidate new concepts with previous information so that a reasonable selection of barrier materials, dimensions and vertical position can be made. Coning theories previously developed are briefly reviewed and an effort i,s made to reduce the results of coning-theory calculations to a point where routine calculations can be made with a desk calculator. It is expected that these simplified calculations will give usable predictions of the amounts of improvement attainable with barriers of various dimensions. Apparatus and procedures used for testing the suitability of commercial cements are described and test results are presented. INTRODUCTION Just about as soon as the phenomenon of water coning was recognized as an oilfield problem, there were suggestions that the production of water coning could be controlled or completely suppressed by means of horizontal barriers. It was also suggested that natural barriers such as shale streaks were helpful in restricting bottom-water production. The implication was that wells not having the benefit of continuous shale streaks to suppress bottom waters should, in some way, be supplied with an artificial barrier. With regard to the selection of barrier materials, there are many references which give the merits of liquid barriers.',' These liquids include surface-active agents," recipitates' and emu1sions. There is no real need to review the merits of these materials again. This paper deals with the use of solid barriers which could be made from various cements. The two major restrictions placed on these barrier cements are that (1) they must be commercially available in large quantities, and (2) they must be applicable by means of standard tools and equipment with techniques that have been fully developed and are in general use at the present time. A schematic drawing of a horizontal barrier in a reservoir is shown in Fig. 1. Two maximum stable water cones are illustrated-—-one for the wellbore diameter and the other for a barrier. A maximum stable cone is one that has attained its maximum volume at the critical production rate and is on the threshold of producing water. The volume displaced by each water cone and the rise in water table are indications of the amount of water-free oil produced. Corrections for porosity, connate water and residual oil, of course, must be applied. The water-oil interface which defines a maximum stable cone is called a free surface. It is a surface over which the pressure is constant. This free surface has the shape of a limiting streamline at and below which there is no movement or transport. The shape of the water cone describes the pressure drop in the reservoir. The effect of a completely impermeable barrier on the cone shape is essentially the same as extending the wellbore out to the barrier radius. The placement of a horizontal barrier requires that a horizontal fracture be created using a single-point entry technique. Two methods may be employed for filling this fracture. One method consists of propping the fracture before filling with cement. The other consists of fracturing with fracture fluid, then immediately following with cement

By R. W. Jenkins, O. J. Neslage

MINE operators today are paying increased attention to the mechanization of drilling operations as an important factor in increasing efficiency and decreasing costs. Recent progress in the design of drill jibs for mounting on drill carriages, or jumbos, has done much to advance the mechanization of mining methods. This progress has introduced new opportunities in the application of "jib jumbos" that are worth serious consideration. An attempt will be made here to classify the various types of jumbos and drill mountings available for level development and flat stope work, t6 indicate applications, and to measure their effectiveness in relation to their cost. The data here are based on a wide variety of field usage, and are offered only to point up, in a general way, the relative efficiency in proportion to cost. It should be remembered that any contemplated jumbo installation must be studied to determine what type of installation is most suitable, considering ground conditions, loading, timbering and haulage equipment, service available, and attitude of manpower. Early Drill Carriages: The advantages of some sort of a drill carriage were recognized at the time rock drills were introduced. In drift or heading operations where a fairly standard drill round and cross section were anticipated, as well as in flat bedded deposits where standard slabbing rounds were used, track and crawler-mounted drills found an early application. These first drill jumbos were little more than drill carriers, designed locally and manufactured with materials at hand. Of comparatively simple construction, function, and low capital cost, they usually consisted of a hinged column which supported one or more drills on arms or universal bars. When the column was pivoted vertically, the drills were moved into position. Screw jack extensions reached from the column to the roof and floor to hold the drill rigid. In some cases, particularly in tunnel jumbos, enough weight was carried that rail clamps or roof jacks were sufficient. Many of these column and arm-type jumbos, usually equipped with air and water manifolds, steel racks, and staging for drillers, are still in use today. Some have employed air or hydraulic extensions for securing the columns. They offer the equip-saving advantage of having all the necessary out, ment together, and they un be moved i and t. set up and torn down as a unit. Boom-type Jumbos: When the advantages of to column-type jumbo were seen, operators could to realize the further gains possible. More time could be saved with mechanical assistance to position api drill vertically. A rack on the column and a pinion on the arm for raising and lowering the drill in the manner of a quarry bar were tried with some success. The most outstanding solution to the vertical handling problem was reached with the boom-type of jumbo. Here two or more machines were mounted on a cross arm at the end of a boom that was pivoted at the rear of the track. This was raised and lowered by various mechanical aids. Occasionally air or hydraulic power was used. Nearly all of today's wagon drills use this boom-type principle. Boom jumbos represent a savings in time and physical effort expended in raising and lowering the drills. The boom must be balanced by the roof of the truck which is secured by rail clamps or type jacks. The most successful application of areawhere this of jumbo has been in the Tri-State area where multiple long-feed machines are used on caterpillar-mounted, boom-type jumbos for slabbing

Jan 1, 1951

By F. G. Miller, R. C. McFarlane, T. D. Mueller

During the process of gas storage in pressure-depleted oil reservoirs, it has been observed that in some instances additional liquid oil is recovered and that the composition of the storage gas is materially altered. A mathematical study was made of the dynamic behavior of such a depleted oil reservoir undergoing gas injection. The important variable considered in this study, not included in previously published work, was that of compositional effects on the phase behavior of two-phase flow. Pressure, saturation and component composition profiles were developed for a linear, horizontal and homogeneous porous medium containing oil and gas but undergoing dry gas injection. Special new techniques were developed to overcome the problems of numerical smoothing which arise in the solution of the equations representing such systems. The method of solution includes the development of partial differential equations describing the behavior of the system, representing these equations by finite difference approximations, making certain simplifying assumptions and, finally, applying methods of numerical analysis with the aid of a high-speed digital computer. In an example calculation, results using the mathematical model are compared with field observations made on a gas storage project in Clay County, Tex. This field project involved a depleted oil reservoir used 'for gas storage and gas cycling purposes. As a result of these processes, the reservoir yielded substantial amounts of secondary oil, both in the form of stock tank oil and as vaporized products in the produced gas. The methods derived in this study may be applied to a variety of oil reservoir problems which are dependent on compositional effects. In recent years the number of oil reservoirs being used for gas storage purposes has increased greatly, and there has been at least one published account of additional oil recovery resulting from gas cycling a depleted oil reservoir after repressur-ing with dry gas for storage purposes. Additional oil recovery from oil reservoirs resulting from gas storage operations could become an important secondary recovery process. This is especially true since the use of natural gas in large metropolitan areas continues to increase and more gas storage volume near these areas is needed. These facts provided the motivation for the work reported here. This paper reports on a study of the inter-relations of composition, saturation and pressure changes which occur when hydrocarbon gas is injected into an oil reservoir system. From an understanding of the process, prediction methods may be developed for use in forecasting the secondary recovery products from gas storage operations in oil reservoirs and, consequently, .the economics of such projects can be developed. The process of storing hydrocarbon gas in an oil reservoir and the cycling process both involve the transient multi-phase flow of oil reservoir fluids with changing fluid compositions. There is a scarcity of work published on the subject. One of the first laboratory models developed to study a problem similar to the one posed here was published in 1948 by Standing, Lindblad and Parsons. l They developed a model to study gas condensate recovery by gas cycling, including the effect of heterogeneous reservoir permeability. Their results showed the compositional effects of injecting a gas of known composition into a two-phase condensate reservoir of known composition. A major finding of their study indicated that maximum oil recoveries from gas cycling projects result when low cycling pressures are used. Previous to their work it was generally considered

By S. R. Dunbas, D. C. Jillson, E. A. Anderson

THE present work was undertaken to furnish information, lacking in the literature, on the deformation mechanisms active in pure titanium at room temperature. Since it was started, Rosi, Dube, and Alexander' have indicated that slip can occur in coarse-grained (2 to 6 mm diameter) titanium on the {1010} and {1011} planes and twinning can take place on the {1072}, (1122) and (1151) planes. Liu and Steinberg,' working with titanium flakes produced by fused salt electrolysis, found evidence of twinning on the {1032$, {1121), {1122}, (1123}, and (1154) planes. The crystals used in the present work were substantially longer (up to nearly 2 in. in length) and possibly purer. Production of Large Crystals It was the purpose of this part of the work to provide single crystal or large grain specimens for use in the deformation studies rather than to study the mechanism of crystal growth. Accordingly, all further exploratory studies on methods were abandoned when it was found that cold-rolled bars sealed in vacuo in individual Vycor tubes and given three or more cycles of 4 hr at 1200°C and three to five days at 850°C, gave large grains. Eighteen specimens about 0.2 in. square x 2 in. long yielded 33 useful grains, ranging from Va in. to nearly 2 in. in length, with an agreeably wide range of orientations, Fig. l. The 0.25 in. thick strip from which the starting specimens were cut had been reduced 67 pct on 18 in. diameter rolls from a scalped, hot-forged (959" to 1000°C), arc-melted, iodide titanium ingot. Thc bar was at room temperature, but the rolls were at 200°C. Reductions of about 0.03 in. per pass were used. The bar was cut into four segments, each of which was rolled in a somewhat different manner. No effect on the growth of large grains was noted. The composition of the titanium, determined on turnings from the ingot scalping operations, is given in Table I. The Rockwell A hardness of the ingot was 26. The standard starting specimens, about 1/4x1/4x2 in., were milled on all four sides, hand polished on 280 and 400 mesh emery papers, etched for 3 min in a 50 HF-50 glycerine solution, rinsed, and dried in alcohol and ether just before sealing them in Vycor tubes. The average specimen weight was 7.5 g, and the tube volume was 6.5 cc. A vacuum of less than 1 micron pressure was applied. The specimen tubes were placed in an evacuated Inconel muffle to minimize the danger of collapse of the glass tubes at temperature. In practice the specimens were first heated to 1200 °C for 4 hr and then transferred fairly quickly to an 850°C furnace where they were held for three to five days. This cycle was repeated at least three times before the specimens were cooled, removed from the tubes, lightly polished and etched on one surface for examinstion. Those in which large grains had not developed were resealed in Vycor and returned to the cycling. Satisfactory specimens (about one out of every four cycled) were polished with emery paper on all four side;, then metallographically polished using ctchinz between wheels to remove distorted metal and, finally, given a very light etch to reveal the grain boundaries. This was necessary because the surface was roughened by the sublimation of titanium under high temperature vacuum conditions. Specimens were identified by TiXl numbers using supplementary letters to designate specific grains.

Jan 1, 1954

By Thomas L. Kesler

Present Raw Materials The lithium industry has had exceptional growth since publication of the last edition of this volume, and the present scale of mining and consumption of raw materials is a great many times that of 1949. The materials of present economic importance consist of four pegmatite minerals and lithium-bearing brine. Spodumene, a lithium pyroxene, occurs in greatest abundance, and is the chief source. It has the formula LiAlSi2O6 and theoretically may contain 8.03 pct Li2O, but in the more important deposits the content is 6.5 to 7.5 pct. The hardness is 6.5, the specific gravity 3.1 to 3.2, and the color mostly pale green to white although deep green, lilac, and yellow varieties exist. The crystals are prisms with strongly developed longitudinal cleavages, and crushing characteristically produces lath-shaped particles. Giant crystals up to 47 ft long are known, but in most occurrences the predominant size range is 0.5 to 12 in. long and 0.1 to 2 in. wide. Hypogene* alteration has formed lithia-bearing sericite and coarser muscovite and rarely eucryptite, while supergene* alteration yields kaolinite and hydrous mica. Lepidolite, of second importance, is a mica of varying composition approximating K2Li3-A14Si7O21(OH,F)3. It has lamellate cleavage, book structure, and a specific gravity of 2.8 to 3. The books range in size from microscopic to a diameter of several inches. The color is mostly violet, but other colors include pink, gray, yellow, and white. Most commercial lepidolite contains 3 to 4 pct Li20 and chemically is in the higher grade range of a series of lithium micas that includes polylithionite, zinnwaldite, and protolithionite. In this series, the content of Li2O is exceptionally as high as 7 pct. Petalite and amblygonite are also of economic importance, but are used in smaller amounts. Petalite has the formula LiA1Si4O10 and is white, gray, or pink. The hardness is 6, the specific gravity 2.4, the cleavage in two planes 114° apart, and the Li2O content commonly 3 to 4.7 pct with a maximum of 4.88. Amblygonite has the formula LiA1FPO4 in which OH may substitute for F to form montebrasite. It is white and has polysynthetic twinning in two directions at 90°. Amblygonite superficially resembles potash feldspar, but has a bluish or grayish tint unlike the cream or salmon tint of the feldspar.[t] The hardness is 6 and the specific gravity 3 to 3.1, and the content of Li2O is the highest among lithium minerals that occur in significant quantity, ranging mostly from 7.5 to 9 pct with a maximum of 10.2. The brine of Searles Lake in California30 has been a commercial source of lithium since 1938. See Chap. 7, p. 108. The "lake" is a saline evaporite deposit, and the exposed part has an area of 12 sq mi. To an average depth of 71 ft, this part of the deposit consists of crystalline salts with 50 pct interstitial voids. The voids are filled with brine that contains mainly sodium and potassium compounds, but the brine also contains 0.015 pct Li2O, which is recovered as dilithium sodium phosphate containing 21 pct Li20. This deposit overlies a

Jan 1, 1960

By J. D. Forrester, Erich Sarapuu, T. C. Cheasley

Electrocarbonization of coal will produce cheap fuel for electric power plants. The complete electrification of industry and domestic power consumption of gas generated as fuel in situ is a worthwhile goal for the coal industry. Production of synthetic oils, gasoline, and coal chemicals from coal gas will create additional new markets for the coal industry. RANKING high in the nation's wealth of natural resources, readily available liquid and gaseous hydrocarbons are nevertheless falling steadily in supply, while industrial requirements for hydrocarbon compounds are greater today than during the peak period of World War 11. Theoretically, several processes will increase the future supply of liquid and gaseous fuels, but the practical application of these methods depends on two controlling factors: 1—that enough carbon-bearing material be available to warrant industrial exploitation, and 2—that the given process be physically, chemically, and economically applicable. With regard to the first factor, the Western Hemisphere is fortunately well supplied, see Table I. Table I not only shows the extensive occurrence of many fuel sources, but also the wide discrepancy among quantities of fuel substances in various materials. Great quantities of potentially available fuel have not been recovered. Many coal seams and other hydrocarbon-bearing deposits are so situated that production is uneconomical by present-day mining or oilwell pumping methods, and even in many exploitable deposits where the most efficient production methods are used a large proportion of material is never recovered. Industrial production of hydrocarbon liquids and gases must be better balanced, and processes must be developed which will convert coals, oil sand, and oil shales into fabricated commodities. Among the techniques employed by scientists and engineers to secure fuel masses not economically available at present are several processes of underground gasification. These are all concerned with converting raw materials into gaseous products by thermal treatment of source substances while they are still in the ground and therefore require that a subsurface heat (fire) zone be induced to affect pervasively the buried raw fuel deposit. This is possible only where sufficiently high temperature exists and where the fuel material is satisfactorily opened or channelized. Also, to compete successfully with common mining or oilfield practices, a given method must be controllable and must not involve greater operational expense than regular methods. Preferably, it should be less expensive. Since the close of World War 11, England has continued field studies of underground gasification methods. Experiments have also been conducted in Sweden, Estonia, France, Belgium, Italy, and Germany. The U. S. Government has sponsored field studies at Gorgas, Ala., and because gasification in situ is vitally important to establishment of the nation's fuel resources, the mining engineering department at the Missouri School of Mines has been actively interested in developing the process of underground electrocarbonization. Research was conceived by Erich Sarapuu, and preliminary experiments in treating bituminous coal were begun at the school in September 1947. The work consisted of laboratory experimentation until June 1948, at which time, through a cooperative agreement with the Sinclair Coal Co. of Missouri, pilot plant studies were instituted at the Tiger mine of the Hume-Sinclair Coal Co. near Hume, Mo., to test the encouraging laboratory findings. This comprehensive field program was pursued continuously until the beginning of 1952."'" The broad term underground electrocarbonization describes a unique gasification process that releases by electricity the desired economic constituents from a raw carbon-bearing material, converting the substance of such deposits into deliverable form and greatly reducing the cost-of-mining factor. Underground electrocarbonization is not subject to the major limitations of many other underground gasifi-

Jan 1, 1955

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By F. I. Stalkup

Vapor-liquid phase equilibrium experiments have been conducted in a static equilibrium cell on mixtures of a light, 45 API stock- tank gravity reservoir fluid and a rich hydrocarbon gas containing approximately 55 mole per cent of intermediate hydrocarbons. Both apressure-vs-composition study of the gas and a simulated reservoir fluid, and a multiple-batch contact simulation of the condensing-gas-drive oil recovery process were performed. In the latter experiments equilibrium gas and liquid compositions were analyzed. Also, conventional, "condensing-gas-drive", long-tube displacement experiments of the reservoir fluid and gases of various richness were performed. The results of these experiments could not be satisfactorily interpreted by the conventional pseudo-ternary-diagram representation of multicom-ponent phase behavior. The results seem to be explained better by considering a bubble-point surface and a dew - point surface joined in a plait-point locus. Portions of the plait-point locus cannot be "seen" directly by the rich hydrocarbon gas because of curvature of the dew-point surface. In such a system, continuous injection of the rich gas over stationary reservoir fluid might form a zone of contiguously miscible compositions from pure rich gas to pure reservoir fluid by: (1) saturating the reservoir fluid with injected gas to the bubble-point surface; (2) creating by mass transfer with fresh injected gas a path of contiguously miscible compositions along the bubble - point surface to the plait-point locus; and (3) creating by mass transfer with additional injected gas a path of gas compositions along the dew-point surface up to the point where direct miscibility results between dew-point fluid and the injected rich gas. INTRODUCTION The use of the pseudo-ternary-phase diagram to illustrate miscible displacement phase behavior has been discussed by several authors.5,7 Such a representation of phase behavior is not rigorous, but the ternary diagram nevertheless gives a qualitative picture of what actually occurs in a miscible displacement process. Fig. 1 is a typical illustration of miscible displacement phase behavior by a ternary diagram. The multicomponent hydrocarbon system is divided into three pseudo-components: a light fraction containing methane and nitrogen, an intermediate fraction containing ethane through hexanes plus carbon dioxide, and a heavy fraction containing heptane and heavier components. A two-phase region is bounded by a dew-point curve and a bubble-point curve, which are joined at the critical point. The concept deduced from such a representation for miscible displacement by a condensing-gas-drive process is as follows: a rich gas G, which lies to the right of the limiting tie line through the critical point C, is injected into the reservoir and contacts reservoir fluid L, saturating the reservoir fluid to give bubble-point fluid L1 and equilibrium dew-point gas GI. Continued injection of rich gas changes the composition of the saturated liquid L1 through a series of liquid compositions lying along the bubble-point curve, until the critical composition C is reached, at which point direct miscibility with the rich gas is achieved. Some equilibrium gas with compositions lying along the dew-point curve from G1 to C is also formed in this process. Thus, continuous injection of rich gas forms a

Jan 1, 1966