Search Documents

By A. T. Janssen

Production planning of direct-shipping ore from a number of relatively small deposits serves to sequence development and mining of these deposits so that both long- and short-range demand can be met while the timing of development cost is such that the average annual rate is minimized. Hand-computed methods have the disadvantage that they require substantial effort and time and cannot be exhaustive. The application of operations research and computers not only overcomes these disadvantages, but opens up additional applications, such as feasibility studies involving alternative mining strategies and changes in the ore market. The method employed concerns linear programming and specifically the Big-M algorithm applied to the variant on the simplex technique with penalties applied to deviations from the desired ore grade. Acceptable 20-year production schedules could be generated in relatively little time, i. e. , in less than 200 seconds for the central processor of the Control Data Corporation 6400 system of the University of Colorado in Boulder.

Jan 1, 1969

Until the end of 1960, the small primary aluminum industry in Australia was run by the government. The entire operation was at Bell Bay on the north coast of Tasmania. It consisted of an alumina plant and smelter, owned jointly by the Commonwealth and the State of Tasmania. Apparent domestic demand that year was about 48,000 long tons; 11% thousand came from Bell Bay; the rest was imported. By March 1964, Australia had two fully integrated aluminum companies. The government has stepped out of the picture and the key word of the industry from bauxite to metal is "growth." Present annual capacity of the two companies for making aluminum metal totals 92,000 long tons a year. Australian demand is about 60,000 tons. By 1968 Australian consumption should be 90,000 tons and by 1970 it is expected to reach 107,000 long tons per year. Export markets for bauxite, alumina and metal are developing.

Jan 10, 1964

By John W. King, S. Ralph Austin

Spurred by recent forecasts of greatly increased demands for uranium by 1980 and beyond, interest is once again focusing on America's western uranium deposits. One of the principal producers in this area is the Gas Hills district in Wyoming, the site of approximately 12% of the known uranium in the U.S., including past production and current reserves. Located on the south flank of the Wind River Basin, the Gas Hills deposits have been recently studied by the Atomic Energy commission for clues to and guides for discovering similar-occurring ores. The ore deposits are confined to a permeable sandstone unit, up to 350 ft thick, at or near the base of the upper Wind River formation of early Eocene age. The uranium occurs in three principal north- south "ore trends," each of which is about six miles long, one mile wide, and separated from each other by approximately three miles (Fig. 1).

Jan 5, 1966

A mine that staggers the imagination is Chuquicamata, the granddaddy of them all. In 1968 production exceeded 300,000 tons of copper. Production began in 1915 and mining proceeded solely on oxide ores until 1953 when the first treatment of sulfides began. Today the company has mined about 1.2 billion tons of all types of material since inception. The accelerating rate of output can be gauged by the comparable 1946 figure of production-to-date which was 350 million tons. No single mine comes close to touching Chuqui for productivity at its high annual metal yield mining only 90,000 tpd of ore at the luxurious waste-to-ore ratio of 0.6 to 1. However, the complexity of the operation is enormous and the experience required to synchronize the various processes is masked by normal operations and only becomes apparent in times of emergency such as when the slide took place in the pit in February.

Jan 11, 1969

By William E. Ford, Edward Salisbury Dana

1. Normal Class (1) Galena Type 2. Pyritohedral Class (2) Pyrite Type 3. Tetrahedral Class (3) Tetrahedrite Type 4. Plagiohedral Class (4) Cuprite Type 5. Tetartohedral Class (5) Ullmannite Type Mathematical Relations of the Isometric System 50. THE ISOMETRIC SYSTEM embraces all the forms which are referred to three axes of equal lengths and at right angles to each other. Since these axes are mutually interchangeable it is customary to designate them all by the letter a. When properly orientated (i.e. placed in the commonly accepted position for study) one of these axes has a vertical position and of the two which lie in the horizontal plane, one is perpendicular and the other parallel to the observer. The order in which the axes are referred to in giving the relations of any face to them is indicated in Fig. 85 by lettering them a,, a2 and a3. The positive and negative ends of each axis are also shown.

Jan 1, 1922

By M. T. Melvin, N. P. Kripakov

The practical application of a post-processing modeling procedure to simulate progressive rock failure around the periphery of coal mine entries is presented. This numerical scheme utilizes a simple rock model that incorporates easily obtainable input parameters consistent with basic rock mechanics principles. These parameters include the cohesion, angle of internal friction, modulus of elasticity, and Poisson's ratio of the bedded deposits that comprise the imediate roof, coal seam, and immediate floor. The geometry of the entry, along with the in situ stresses existing at a mine site prior to mining, are also considered in the analysis. The potential of this procedure as a predictive tool in determining the extent of pillar rib fracturing and yielding of the immediate roof and floor is evaluated assuming a Mohr- Coulomb failure criterion. The procedure is designed to be user oriented and is adaptable to any finite element code with linear elastic capability, making it particularly attractive to users with limited budgets and computer size.

Jan 1, 1983

By H. I-Lieh Huang, O. D. Sherby, J. E. Dorn

RECENT investigations1-4 have suggested that the total plastic strain, C, for high temperature creep under a given stress can be correlated by means of a temperature-compensated time, te- where t is the duration of test, e is the base of natural logarithms, aH is the activation energy for creep, R is the gas constant, and T is the absolute temperature. A typical set of data on which this deduction was based is given in Fig. la. Inasmuch as the e-in t curves for the various temperatures are identical except for their displacement along the In t axis where f and are appropriate functions. If the increase in creep rate with an increase in temperature is exclusively ascribable to a single process involv- ing thermal activation, (T) should equal RT and therefore it = constant [2] where ?= te Assuming the validity of this relationship, ? = ?2 at the same strain, or where the subscripts refer to two alternate test conditions.

Jan 1, 1957

By Carl F. Dietz, Dyke V. Keedy

The problem of drying ores is one that most mill-engvineers are sooner or later called upon to meet, and it may be timely to point out some of the difficulties resulting from such operations from purely a metallurgical and economic standpoint. We mean, in the following pages, to discuss primarily the effect of such operations on the ore. itself, without particular reference to the mechanical or cost features of the subject. That an appreciable tonnage of the ore fed to the usual form of drier, either rotary or stack, is lost, is fairly well appreciated, but we believe that only a few mill-managers know just what their drier-losses amouilt to, and we have found that in most cases they console themselves with the fact that the drier-smoke is not very much discolored, and it is generally believed that the draft is not sufficient to carry away more than a negligible percentage of the values.

Jan 1, 1913

By Yoon T. Auck, Milton E. Wadsworth

Column leach studies of two low grade prophyry copper ores were made with variables of size, flow rate, pH, drainage rate and tempature. Evidence is presented to show that, in some types of ores, sulfide minerals block leaching channels and regulate the rate of dissolution of gangue constituents. Basic iron sulfates, dissolved by introducing acid, provide oxidizing agent in the form of ferric ion in the absence of oxygen. Ferric ion then acts to release copper from the ore. Oxygen up-take was found to increase with the lowering of the pH and to follow parabolic kinetics attributable to the precipitation of basic iron salts within the pore channels. Slow drainage of residual gravitational water can seriously retard oxygen up-take during oxidation for particles in the coarse sand range. A model is presented for dump leaching in which a reaction zone connected by channels to the surface of the ore particle moves topo-chemically during the course of the reaction.

Jan 1, 1973

By Albert Smith

THE creep properties of metals have as-sumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Insti-tute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influ-ence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investi-gate creep phenomena because of the sim-plicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals.

Jan 1, 1940

By C. P. Proctor, J. T. Crawford

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium about 1841. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing in the nineteenth century. Chapman and Mott' describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan, Lodge, Elliott, Blackett, and Murton. The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification.

Jan 1, 1943

By Lawrence Henderson

TO increase tonnage in the early days of coal mining it was necessary only to hire more men. The job now is to increase the tons per man, but other troubles arise because this has been accomplished. With the introduction of continuous miners, newer and faster loading machines, and faster belt conveyors the safety engineer has been faced with new difficulties. Use of larger equipment created roof control problems, which were thoroughly studied by the safety engineers of various companies. With the assistance of the U. S. Bureau of Mines, safety engineers in Alabama conducted roof bolting experiments wherever they appeared to be applicable. Accident records before and after the method was adopted showed results more than justifying the efforts and funds expended. The larger mining companies responded enthusiastically to the program because roof bolting not only prevented accidents but also increased production efficiency, in many cases rep- resenting the margin between profit and loss. In Alabama today there are miles of roof supported by bolts.

Jan 8, 1957

By Gerald Edmunds, R. K. Waring, E. A. Anderson

Brass is liable to failure under the combined influence of stress, certain corrosion media, and time, a phenomenon commonly termed season cracking or stress-corrosion cracking. The consequences of this are serious in applications of brass generally, including the important field of cartridge cases. Cartridge cases (70 Cu: 30 Zn) that fail from this cause may allow the escape of gas from the gun breech, a hazard to the shooter, and may not eject, thus temporarily putting the gun out of action. In loaded cartridge cases, the stress present is partly residual from the, drawing and necking operations and partly applied by the insertion of the projectile. Ammonia, present as a decomposition product of smokeless powder, air and moisture constitute corrosive media. The prevalence of season cracking has been reduced considerably, but not eliminated, during the past quarter of a century by low-temperature annealing to relieve stresses residual from fabrication, a method suggested by Diegel 38 yr. ago(I).2

Jan 1, 1945

By R. S. Archer

THE binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.1 Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application.

Jan 1, 1930

Note Any member who desires to be designated as being "Available for Consulting Work" can arrange it simply by sending a written request to the office of the Secretary of the Institute The following list of members is primarily arranged geographically, with secondary consideration to political subdivisions arranged alphabetically First, the states of the United States , then other North America, in order Alaska, Canada, Mexico, the West Indies, and Central America Then cones South America, Europe, Africa, and Asia, each including the near by islands associated with those continents Australia, the islands to the north, and the Pacific islands except Japan are grouped together under Oceania The various countries are indexed on the preceding page NORTH AMERICA UNITED STATES ALABAMA America -Dyar, G C Anniston -DePriest, S H Klugh, B G Lefforge, J W Auburn Poor, R S Bankhead -Armstrong, W D Bessemer -Beck, A IV, Jr Carnes, D Chabot, L S , Jr Creveling, J C

Jan 1, 1952

For more than 100 years, the Republic of Chile has been one of the leading copper-producing countries of the world. Between 1877 and 1880 Chile accounted for over 50 pet of total world copper production. Today it has the world's largest known reserves of copper ore and a capability of producing over 600,000 tons per year. This capacity can and will be increased as the world demand for copper grows steadily during the remaining years of this century. The Potrerillos mine of Andes Copper Mining Co., a subsidiary of The Anaconda Co., was developed in the rugged, high Cordilleras in the early 1920's, and the townsite, concentrator, leaching plants, smelter, railroad, power and port facilities were completed so that it came into full production in 1927. Since then and until the closing o f the mine in June of last year, 1,762,192 tons o f copper were produced.

Jan 4, 1960

By P. S. Bagga, P. T. Luckie

Liberation (the process of destroying the interlock between unwanted materials, such as mineral matter and pyrite, and coal) is one of the most important precursors to the benefication of raw coal in order to produce high grade marketable coals at economical recovery levels. Liberation is achieved usually by comminuting the raw coal. However, because of the significant interaction between the production of fine particles to achieve liberation and the cost of separating fine particles, the coal industry needs a method projecting the change in washability with size reduction. Such a projection can be combined with size reduction and separation simulators in order to examine completely beneficiation circuitry to produce coals of stringent specification. This paper presents the development of an appropriate liberation model for coal and its solution by Monte Carlo simulation to predict the expected washability of the raw coal as a function of comminution. It includes model validation with a known binary mixture as well as with a known teritary mixture.

Jan 1, 1983

By A. A. Stripling

The Cretaceous limestone wells of the Mara/Maru-caibo Dist. of Venezuela are extremely prolific producers. To maintain production on cessation of natural flow, large scale gas-lift operations were commenced involving high production rates on caring Flow. For the design of these gas-lift installations it was essential to have some knowledge of the pressure gradients involved in casing flow, so that the required injection pressures, optimum gas injection raws, etc., could be forecast. This paper presents a method of calculating these annular pressure gradients. Basically the method makes use of an energy balance equation coupled with an empirical energy loss factor derived from field data. The calculations have been put in a form suitable for "punch card-type" calculating machines. A set of gradient curves for Mara/Maracaibo conditions covering flow rates up to 12,000 B/D, and GOR's of 500 to 2,000 cu fd/bbl is presented. From these curves the flowing BHP can be predicted from surface data and the vertical pow performance under varying conditions of gas injection can be estimated. The method has been applied to La Paz and Mam gas-lift operations for over three years and has given consistently accurate results. INTRODUCTION The Cretaceous limestone fields of the Mara/Maracaibo area in Venezuela are characterized by the presence of widely distributed fissure systems. Under these conditions individual wells frequently have extremely high potentials and such wells are generally flowed on the casing-tubing annulus in order to reduce the pressure loss in vertical flow. To maintain production on cessation of natural flow, an extensive gas-lift system was planned. As a first approach to this gas-lift design problem, an attempt was made to construct a set of empirical flowing gradient curves from the available subsurface pressure data. Such a method has been used successfully for tubing-flow conditions in California by Gilbert'. Unfortunately, the empirical construction of casing-flow gradient curves presents additional difficulties, as pres- sure bombs cannot bc run in the casing-tubing annulus against high rates of flow. Thus, the Full flowing gradients cannot be defined by actual measurement and the best that can be done is to obtain spot pressures at the tubing shoe. Under these conditions a vast accumulation of BHP data is required to construct a set of gradients. To the La Paz and Mara fields the majority of the available flowing pressure measurements fall into a relatively narrow GOR range, in the neighborhood of the solution ratio. While there appeared to be reasonable prospects of constructing gradient curves for this limited range, measurements at higher GOR's, which were of major interest for gas-lift operations, were relatively few and the prospects of constructing empirical curves cor~spondingly remote. As an alternative approach, the possibilities of a mathematical analysis of vertical flow conditions were investigated. May and Laird2fV n 1934 presented an excellent analysis of the vertical-flow conditions in the Anglo-Iranian Oil Co.'s fields. Their analysis was based on an energy-balance equation and calculated the losses due to kinetic energy, friction and slippage separately. By combining these losses with the total calculated available energy, the required depth-pressure traverse could be deduced. On applying the method to La Paz conditions, good results were obtained for tubing flow at high tubing-head pressures. However, for lower wellhead pressures (300 psi and under) the discrepancy between calculated and measured values increased appreciably. It was considered that this was probably due to energy losses caused by slippage or liquid hang-up in a continuous gas phase, for which it was difficult to visualize any analytical approach. In 1952 Poettmann and Carpenter4 presented a method of pressure gradient calculation which, while based on an energy-balance equation similar to that employed by May and Laird, made no attempt to evaluate the various components making up the total energy loss resulting from irreversibilities of flowing fluids. Instead, they proposed a method of analysis which assumed that all significant losses for multiphase flow could be correlated in a form similar to that of the Fanning equation for frictional losses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The total available

By Joseph W. Leonard

The purpose of this paper is to review and discuss some of the less evident and sometimes neglected opportunities for progressive developments in coal research. While a great deal of both promotional and technical information flows from some areas of coal research, output deficiencies in other areas of activity have reached a magnitude where important developments have been, and will increasingly be, unfavorably affected. These areas mainly involve coal mining and preparation. Some recommendations for the intensification of effort in these areas follow: Coal Mining While a huge tonnage of in-the-ground coal is assured, the location and distribution of these tonnages are becoming less favorable. The easy-to-mine coal which is located in or near population centers has been, or is being, mined. The vigor with which the less accessible reserves are recovered by the mining industry depends largely on the condition of the coal market at the time of mining. Hence, during a buyer's market, the commercially oriented mining industry is compelled to mine the easier and less costly reserves. Conversely, during a seller's market, the need to rapidly expand production results in more difficult mining and higher cost coal as few obstacles are encountered in finding markets. Hence, a seller's market tends to enhance the recovery of reserves while a buyer's market does not. One reason for today's fuel supply problems is that the Nation has recently emerged from a long-term coal buyer's market which lasted from about 1950 to 1968. During that period, national policy caused severe production cutbacks which regretably drove the industry to mining only the more accessible and better quality reserves. Often in order to remain in business, many hundreds of millions of tons of more difficult to mine reserves were abandoned and lost behind caved areas. Many of these reserves are close to population areas and would not have been lost in a more stable economic climate. It is difficult to fully account for all the impacts that were caused by the great buyer's market of the 1950s and 1960s. Besides the obvious loss of reserves that were once considered national wealth, the mining of better reserves tended to produce a generation of technically optimistic mining people. Mining people frequently became accustomed to looking at nothing less than outstanding mining conditions as a result of the declining market. Many are now and have long since received a re-education in the other half of mining. Going from many years of mining accessible, select and easy-to-win reserves, to the crash-driving of development entries in reserves that were considered unworthy of mining during 50s and 60s, frequently results in a much higher rate of encounter with in-seam and out-of-seam rock as well as with coal-deficient areas or "washouts." Intensive entry driving activity and compulsory non-selective mining in sometimes lean reserves were brought on by the need to rapidly open up new supplies of coal. Working under these requirements presents a continuing reminder that much more needs to be known about the relatively esoteric art of planning the best direction for driving entries in order to insure that a more consistent and greater supply of coal is available during early mine development. All of the preceding discussion tends to point to a need for a better estimate of those reserves of coal that are likely to be mined in the future. Such estimates should not be limited to the compilation of the amount of coal in the ground; but, where possible, should also include information concerning the capability for producing this coal. After all, a coal seam of ample thickness may have a degree of thickness variability, undulation, bad roof or floor, so as to make what would otherwise appear to be an attractive mining condition untenable. Underlying the problem involving the feasibility of producing known reserves is the need to develop better methods for the characterization of coal seams and associated lithotypes, based on drill core data, once at area is selected for mining. Reserves and their characterization involve aspects of exploration technology that are frequently considered mature. The resulting technological deficiencies may be the main reason why coal exploration frequently does not end with core drilling of a property, as it should, but extends into the mining operation during the driving of development entries. When exploration is extended to the driving of development entries, the near absence of integrated decision-making theory involving mining, geology, mathematics, and economics becomes, once again, all too painfully apparent and frequently results in very costly rationalizations. Hence, by the formal initiation of a concentrated program to combine the cyclical effects of economics with geology and mining, more relevant estimates of reserve distribution, tonnages, and production capability should be forthcoming. Moreover, a similar formal effort is needed to develop a combination of the most advanced concepts of mathematics, geology, and mining to better "see" coal seams as a means to favorably implement many long-range decisions involving mine safety and productivity. Much more applied research needs to be done on coal mining systems for mining in thin seams and/or under bad roof. Current difficulties in both of these areas at recently opened coal mines should provide a sobering glimpse into the future. Full-scale applied research, sponsored by appropriate federal agencies, is urgently needed on a scheme involving a new combination of established mining and preparation elements. The scheme may include: (1) a continuous mining machine remotely operated by a miner stationed at some distance behind the machine using a cord attached control box; (2) hydraulic transport of coal through pipes from the mining machine to a coarse refuse removal grid, crusher, and then on to portable concentrating equipment; (3) the hydraulic transport of clean coal out of the mine in pipes to the surface for thermal dewatering, if neces-

Jan 1, 1974

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

IN THE past year, Jaffee and Campbell&apos; and Finlay and Snyder2 reported on the mechanical properties of titanium-base alloys, some of which were in the same ranges of composition as are covered in this paper. In this paper, evidence confirming that given by Finlay and Snyder on the effects of carbon, oxygen, and nitrogen on titanium will be presented; and, in addition, new data will be given on the effects of these elements on the flow properties and phase transformation of titanium. Materials and Preparation of Alloys The preparation and general properties of iodide titanium have been adequately described elsewhere.&apos; , As-deposited iodide titanium rod, prepared at Battelle, of Vickers hardness less than 90 was employed as the base metal in the present work. This was the same material as that used by Finlay and Snyder.2 The probable analysis reported by them for standard quality metal holds here also: N 0.005 pct, 0 0.01 pct, C 0.03 pct, Fe <0.04 pct, A1 <0.05 pct, Si <0.03 pct, and Ti 99.85 pct. Carbon was added in the form of flake graphite supplied by the Joseph Dixon Crucible Co. Oxygen was added in the form of c.p. grade TiO, powder, produced by J. T. Baker Chemical Co. Nitrogen was added in Ti3N4 powder, supplied by the Remington Arms Co. Individual ingots weighed 7 or 8 g. Carbon, oxygen, or nitrogen was added by placing the corresponding powder in a capsule made from as-deposited iodide titanium rods and melting the capsule with the balance of the charge. The charge was are-melted with a tungsten electrode on a water-cooled copper hearth under a partial vacuum of very pure argon (99.92 pct minimum). Melting was practically contamination free. Vick-ers hardness increases of less than 10 points were normal for unalloyed iodide titanium control melts. Nitrogen analyses of are-melted iodide titanium showed a nitrogen content of 0.005 pct, about the same as is present in the as-deposited rod. No tungsten pickup was found in a melt of iodide titanium analyzed for tungsten. Weight losses in melting nitrogen-free alloys were very small and varied consistently from nil to 0.015 g (0 to 0.2 pct). This permitted the use of nominal composition for these alloys. Chemical analyses made for carbon, which can be analyzed conveniently by combustion methods, justified this procedure. Where nitrogen was added, considerable splattering took place. Here it was necessary to analyze for nitrogen by the Kjeldahl method. The ingots were hot rolled at 850°C to about 0.045 in. thick. After hot rolling, the strips were descaled by mechanical grinding, and then given a cold reduction of 5 to 10 pct to insure a uniform thickness throughout the length of the specimen. The edge strips and the tensile strips were annealed in a vacuum of 1x10-4 mm Hg pressure for 3 1/2 hr at 850°C and furnace cooled. Methods of Investigation Hardness Measurements: At least five Vickers hardness measurements were taken using a 10-kg load on each sample in the following conditions: (1) top and bottom of each ingot, (2) top and bottom surface of as-rolled and annealed sheet, and (3) on cross-section of annealed sheet and all quenched specimens. Tensile Tests: Tensile tests were conducted on Baldwin-Southwark testing machines having load ranges of 600 or 2000 lb. Tests were made on 1-in. gauge-length specimens, 3 1/4-in. overall length, 1/2 in. wide, 0.040 in. thick, with a reduced section 1 1/4 in. long and 0.250 in. wide. Two SR-4, A-7 strain gauges, one mounted on each side of the specimen, were used to measure the strain over a limited range to determine the modulus of elasticity. After the modulus of elasticity readings had been taken, load vs. strain readings were taken, using only one strain gauge, at increments of 0.0001 in. until the yield points were passed and then at 0.001-in. increments to the limit of the strain-gauge indicator (0.02 in.). Strain readings above 0.02 in. per in. were taken every 0.01 in., using dividers to measure the strain between the 1-in. gauge marks until the maximum load had been reached. Crosshead speed, when using the SR-4 gauges, was 0.005 in. per min, and, when using dividers, 0.01 in. per min. Flow Curves: Flow curves were determined using the true stress-true strain data obtained during the tension test. The usefulness of this type of information has been dealt with very adequately elsewhere by L. R. Jackson,&apos; J. H. Hollomon,6 and many others. Flow curves of true stress vs. true strain could be converted to the more conventional cold-work curve of 0.2 pct offset yield strength vs. percentage of cold reduction by means of the transformation, 1/1 = 1/1-R, where R is the fraction reduction in cold working. Thus, the true strains corresponding to percentage reduction can be calculated, and the 0.2 pct offset yield strengths scaled off the — 6 curve by taking the true stresses corresponding to the values of 6 + 0.002 strain. Heat Treatment: For the transformation studies, the alloys were heat treated in a horizontal-tube furnace using a dried 99.92 pct argon atmosphere, and quenched into water. Essentially no contamination was found after several hours of heat treatment at temperatures up to 1050°C. Metallography: Specimens were prepared in the

Jan 1, 1951