Search Documents

By John T. Eash

DURING the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin, 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. SELECTION OF COMPOSITION While the final criterion of the suitability of an alloy for a bearing must 0f course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstructure, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig. I. In addition, the tin bronze contains the hard alpha + delta eutectoid constituent distributed through-

Jan 1, 1945

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig' 1. I' In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By Richard V. Hughes, Rudolf J. Pfister

The necessity for getting more water into sands of low permeability in any secondary-recovery water-flood operation in order to recover all the available oil always has been a major problem. In the early days of water-flooding the addition of soda ash and caustic soda to fresh input waters was recommended and tried without success in the Bradford field. The most frequent difficulty was sand plugging. The use of natural and artificial brines often has been suggested for water-flooding, in the belief that laboratory observations of decreasing fresh-water throughput rates in measuring water permeabilities of consolidated sand cores might be partially explained by swelling of clays. A review of available literature bearing on the subject and related laboratory experiments are presented herein, offering an explanation for failure in use of soda ash and caustic soda waters and supporting the recent concept that every water used for input purposes in the secondary recovery of oil should possess such physical and chemical characteristics as to keep the clay content of the producing sands in a permanently flocculated condition. Produced brines meet this requirement. Their use is recommended as a means of increasing intake rates of tight sands and oil recoveries, as a solution to brine-disposal problems, and as a means of conserving a natural resource. Introduction There is a general belief among those engaged in the secondary recovery of oil by water-flooding that one of the most important requirements for the success of any such project is an adequate supply of good, fresh water. Fresh waters have the advantages of being more easily stabilized than salt waters and of being usable about the lease for all purposes. The use of brines for water-flooding never has been given much consideration in the Pennsylvania Grade area. The use of brines in Mid-Continent operations has been considered largely as a substitute for fresh waters, which were economically unobtainable for many operations. Estimated recoveries for some water-drive fields indicate that less of the original oil in place will be left upon abandonment than with the above-average practices used in Pennsylvania Grade water-flood operations. Lower residual oil saturations than 25 pct of the pore space following the water-flooding of Third Bradford sand cores in the laboratory are unusual. In comparison, water-flushed sands surrounding any virgin oil pool are found to be practically devoid of oil. Such lower natural residual oil saturations may be the result of a time factor much longer than economic under artificial water-flood operations, but neither the producer of primary oil nor the producer of oil by secondary recovery can obtain maximum recoveries unless full advantage is taken of all natural forces and

Jan 1, 1947

By Richard V. Hughes, Rudolf J. Pfister

The necessity for getting more water into sands of low permeability in any secondary-recovery water-flood operation in order to recover all the available oil always has been a major problem. In the early days of water-flooding the addition of soda ash and caustic soda to fresh input waters was recommended and tried without success in the Bradford field. The most frequent difficulty was sand plugging. The use of natural and artificial brines often has been suggested for water-flooding, in the belief that laboratory observations of decreasing fresh-water throughput rates in measuring water permeabilities of consolidated sand cores might be partially explained by swelling of clays. A review of available literature bearing on the subject and related laboratory experiments are presented herein, offering an explanation for failure in use of soda ash and caustic soda waters and supporting the recent concept that every water used for input purposes in the secondary recovery of oil should possess such physical and chemical characteristics as to keep the clay content of the producing sands in a permanently flocculated condition. Produced brines meet this requirement. Their use is recommended as a means of increasing intake rates of tight sands and oil recoveries, as a solution to brine-disposal problems, and as a means of conserving a natural resource. Introduction There is a general belief among those engaged in the secondary recovery of oil by water-flooding that one of the most important requirements for the success of any such project is an adequate supply of good, fresh water. Fresh waters have the advantages of being more easily stabilized than salt waters and of being usable about the lease for all purposes. The use of brines for water-flooding never has been given much consideration in the Pennsylvania Grade area. The use of brines in Mid-Continent operations has been considered largely as a substitute for fresh waters, which were economically unobtainable for many operations. Estimated recoveries for some water-drive fields indicate that less of the original oil in place will be left upon abandonment than with the above-average practices used in Pennsylvania Grade water-flood operations. Lower residual oil saturations than 25 pct of the pore space following the water-flooding of Third Bradford sand cores in the laboratory are unusual. In comparison, water-flushed sands surrounding any virgin oil pool are found to be practically devoid of oil. Such lower natural residual oil saturations may be the result of a time factor much longer than economic under artificial water-flood operations, but neither the producer of primary oil nor the producer of oil by secondary recovery can obtain maximum recoveries unless full advantage is taken of all natural forces and

Jan 1, 1947

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig' 1. I' In the tin bronze contains the hard alpha + delta

Jan 1, 1946

amounted to about 2000 metric tons. The total output is increasing from year to year. Marine salt is now produced in Haiti in quantity sufficient to supply nearly all the requirements of this Republic, so production tax is now collected. Central America Guatemala-The major production of salt in Guatemala is solar salt derived from sea water, but the Indian population prefers salt derived by boiling coastal marine earth. Salt is taxed by the Government. The industry has been beset by controversies in recent years, especially following the revolution of October 1944. The Government issued a decree in August 1940 designed to control production and price of salt. The creation of a salt consortium was provided for and marketing was to be governed by production quotas. It is understood that the Government pool was later dissolved and the industry is now under older laws whereby production and sales have no limits. South America Panama-Output of salt in Panama in a very recent year was 11,000 net tons of solar-evaporated sea salt. A Government bank is in charge of output and distribution of the product. Colombia-Rock-salt deposits are known in five places-Zipaquira, Nemocon, and Sesquile, in the Department of Cundinamarca, the Cumural y Upin near Restrepo, and San Miguel y Barital, near Medina in Meta Intendency. The latter deposit never has been worked on account of its inaccessibility. Saline springs are worked in four locations. The largest producer among marine salinas is Manare but it is now planned to make Bahia Honda the largest. Some evaporated salt is made in vacuum pans. The deposits at Zipaquira, Nemocon, and Sesquile are believed to occur in the domal type of deposit. All the salt resources are under Government control. Venezuela-The salt industry in Venezuela is under Government control and is taxed. Taxes in recent years, however, have been reduced for salt used in curing hides and salting meats, fish and fish products. Production has approximated 25,000 metric tons yearly but may now be considerably above that figure. The basin on the peninsula of Araya, State of Sucre, which at present is the only important source of salt, could produce at least 175,000 metric tons if more ground were provided-a larger supply than the entire country could consume. This unique landlocked basin of nearly 1000 acres lies 12 ft below sea level. Ecuador-Salt is a Government monopoly in Ecuador and is produced chiefly by solar evaporation close to the shore. The main producing center is on the Santa Elena peninsula, which supplies about 90 pct of the salt. Small fields are at Punta Arenas, Payana, and Chara-

Jan 1, 1949

By G. W. Gross

A commercial deposit of white kaolinite clay contained in the sandy overburden of the Cambrian Gatesburg formation in Central Pennsylvania was successfully mapped by combined SP and resistivity methods and results were checked by drilling. Resistivity minima in the range between roughly 2000 and 3500 ohm-meters coupled with second-order SP maxima of 50-60 mV contrast were found to characterize commercial white kaolinite clay beneath not more than 30-40 ft. of sandy overburden in the area stdied. This investigation supports the hypothesis, established previously, that certain SP phenomena may reasonably be ascribed to diffusion and membrane potentials produced by interaction of clay lenses, sandy matrix, and ground waters. The success of this test proves that this prospecting technique can assist in locating clay deposits in sandy overburden derived from the weathering of sandstones and carbonate rocks such as the Cambrian formations of Central Pennsylvania. In a recent paper, Gross and Moore (1959) described broad self-potential minima above the outcrops of the Cambrian Gatesburg formation. These "first-order" SP anomalies, of 220-350 mV contrast (Figure 7), are related to the peculiar sandy residual soil covering the Gatesburg formation. Small positive ("second-order") peaks of 50-60 mV contrast are superposed on the bottom or flanks of the first-order troughs. They appear to be related to lenses and layers of kaolinite clays within the sandy Gatesburg overburden. Both first-order and second-order anomalies show a characteristic inverse relationship with apparent resistivity profiles in most cases. An explanation in terns of liquid-junction and shale potentials was advanced. According to this working hypothesis, shale potentials are generated: 1) at the contact of the sandy Gatesburg overburden with the more argillaceous soils of surrounding formations; 2) at the boundary of clay lenses contained in the sandy matrix of that overburden. Concentration gradients between interstitial infiltration waters and perched water tables within the Gatesburg overburden are believed to give rise to the liquid-junction potentials. In order to test this hypothesis further, a detailed study was carried out of a second-order positive anomaly on the property of the Woodbury Clay Co. at Mines (Blair County, Pa., Hollidaysburg folio of the U.S. Geological Survey). A second aim was to establish if combined SP and resistivity surveys are suitable as a practical method for delimiting favorable areas in which commercial kaolinite clay de~osits may be found by drilling. Drilling control was provided by the Woodbury Clay Co. PROCEDURES Instrumentation used for SP measurements was the same as described in the paper mentioned. For resistivity surveys, a direct-current voltmeter-ammeter device built by Georator Gorp. of Manassas (Va.) was used in combination with non-polarizing electrodes from the same manufacturer. Power was supplied by one to six 45-volt, heavy-duty B-batteries

Jan 1, 1961

By A. W. Jenike

A theory of gravity flow of bulk solids like ores, concentrates, coal is outlined and an example of design for unobstructed flow is given. Mass-flow and plug-flow patterns are defined and related to the geometry of the bin. The effect of these patterns on segregation, first in-first out flow, and caking is described. This paper is a report on the results from the AIME sponsored project "Flow of Bulk Solids" which was carried out under the author's direction at the Utah Engineering Experiment Station, University of Utah, during the period 1956-1962. The theory has been applied to the design of numerous industrial storage plants. A QUANTITATIVE METHOD OF DESIGN FOR FLOW There is hardly an industry which does not store and handle solid materials in bulk form. When the volume of the solids is large, gravity is invariably relied upon to cause the solids to flow out of storage, through channels and chemical reactors. Such materials as ore, coal, cement, flour, plastics, clay, soil, to which a general term of bulk solids is applied, flow by gravity or are expected to flow by gravity in thousands of installations and by billions of tons annually. The chemical and process industry depends on gravity flow of solids in process and out of storage. Mining relies on gravity flow in block-caving, in ore passes, as well as in storage and loading bins. Agriculture uses gravity flow in elevators, in feed plants, and in farm silos. In practice, satisfactory gravity flow is seldom attained. Such problems as doming, piping (rat-holing), lack of live capacity, segregation, deterioration in storage, harass industry. In spite of the universality of these problems, until recently, there has been no theory of solids flow, no method of predicting how a solid would behave, and how the channel, bin, or hopper should be designed. In the late nineteen forties and early fifties, the theory of plasticity came of age and simultaneously the computer became widely available. These two factors permitted the development of a theory of flow of bulk solids. The work was conducted during the years 1953-1961. In conjunction with the development of the theory a method to measure the flowability of solids was also developed1-7 and the theory was ap-plied to the design of ore pockets, storage plants,16 chemical reactors and adsorption columns. A comprehensive report of this work is given in a previous work." THEORY OF FLOW The most important question which a theory of flow has to answer is: what conditions need to be satisfied for a given solid to flow uniformly and without obstructions through a channel? First of all, the following observations are made:

Jan 1, 1967

By George J. Clark

One of the major problems of operation in the anthracite industry is the disposal and handling of refuse—not because of its complexity but because of the quantity and type of material involved. It is the purpose of this paper to describe the kinds of refuse, methods of disposal, quantities of material to be handled and equipment used, together with present day application at specific operations in the Northern, Eastern Middle, Western Middle and Southern anthracite fields. For the purpose of this paper, refuse is considered to be any material that has no present or foreseeable future value and that must be handled and disposed of in the process of mining and preparing anthracite for market. Included in this classification are tunnel rock, mine rock, cleaner plant refuse, breaker refuse, old timber, ashes and silt. Disposal Methods Old timber is disposed of either by burning or by depositing on the refuse bank. Burning is preferred because timber on the refuse bank is a potential fire hazard. Ashes are deposited on a separate bank, mixed with other refuse, or flushed into old mine workings. In many places, the latter practice has caused considerable difficulty in preparation of coal mined from these areas. In depositing ashes on the surface, it is wise to refrain from mixing them with material containing coal as such contamination may prevent reclamation of the coal in future years. Tunnel work, mine rock, cleaner plant and breaker refuse compose the bulk of the material to be disposed of and handled, and are referred to collectively as "refuse" in this paper. Waste material in or adjacent to the coal beds may be removed at the working face wherever possible. This can be done in flat or lightly pitching beds, and in the Northern field represents a sizable percentage of this type of refuse handled. In the other three coal fields, this method of disposal cannot often be used. Refuse not removed at the working face is taken to the surface and generally is deposited on banks; occasionally it is crushed and flushed into old mine workings. Breaker refuse often is used for constructing berms for silt-retention basins. Disposal Problems The problem of handling refuse is different for each operation, owing to topographical conditions, quantity of material to be handled, anticipated requirements and types of equipment in use elsewhere at the operation. Preparation plants with limited refuse-disposal areas, excessive grades to reach the required elevation and long hauls to disposal areas not readily accessible require the selection of equipment to best meet the conditions. The quantity of refuse to be handled from a given amount of raw material varies considerably throughout the four fields. In mine coal, this varies from a low

Jan 1, 1949

By H. M. Roche

MAGNETITE mining and milling in the Eastern States in 1939 showed considerable improvement over 1938. For the first eight months of the year production of magnetite proceeded at a normal rate but operations were stepped up in the last four months owing to increased domestic demand. In New York, the Republic Steel Corp. operated the Witherbee-Sherman mines at Mineville throughout the year. Chateaugay Ore and Iron Co. operated their low-phosphorus mine at Lyon Mountain for the first seven months, but on Aug. 1, Republic Steel took over this mine -and have since operated it. In Pennsylvania, the Bethlehem Steel Co, operated the Cornwall mine continuously. In New Jersey, Mt. Hops and Scrub Oak were in operation all year. The Washington mine went into production on Nov. 1 and the Richard mine on Dec. 1.

Jan 1, 1940

By Nagel, Theodore

USE of oxygen in metallurgical operations was investigated by a committee of unusually able engineers more than ten years ago. A record of their work appeared under the title "The Use of Oxygen or Oxygenated Air in Metallurgical and Allied Processes," Serial 2502, Report of Investigations, U. S. Bureau of Mines. Shortly thereafter the A.I.M.E. published "Use of Oxygenated Air in Metallurgical Operations," based on a symposium at the New York meeting, February 1, 924. Quoting from the Bureau of Mines report In view of the many recent developments in oxygen manufacture, and considering the increasing cost and decreasing quality of our raw materials, the Bureau of Mines has taken the matter of the application of oxygen or oxygenated air to the metallurgical centers for consideration and has appointed an advisory committee to study the problem.

Jan 1, 1935

The Librarian of one of the Government Departments at Washington desires to secure one of the first editions of the Posepny Volume. It is a small book of about 265 pages. The Library in question will gladly pay the sum of $2.50 for the copy.

Jan 9, 1919

By H. L. Hinds, L. L. Trautman

The refining of precious metals from steel wool cathodes is completed by direct fire smelting or acid treatment of the cathodes to dissolve the steel wool followed by fire smelting. To further the refining of the cathodes, the Miller process and the Wohlwill process are used.

Jan 1, 1984

By Albert Zima

ACCORDING to recently published statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet.

Jan 1, 1935

By AIME AIME

JOHN HUNTER NEAD, chief metallurgist of the Inland Steel Co., Chairman of the Iron and Steel Division for 1939, a native of Missouri and graduate of the University of Michigan, first taught chemistry after graduating from college and then decided to follow the field of his college specialization and be a metallurgist. In succession he was associated with the H. H. Franklin Co., Syracuse, N. Y., the Watertown Arsenal, the Racine Steel Castings Co., and the Minneapolis Steel and Machinery Co. During the World War he held a commission as Captain in the Ordnance Department and served both overseas and on the technical staff in Washington. Returning to civilian life, Hunter Nead was research metallurgist and then chief metallurgist of the American Rolling Mill Co. from 1919 until 1931, when he went to his present position with Inland.

Jan 1, 1939

By Robert H. Palmer

Sacuranao Field.—Bacuranao field is about 12 miles east of Havana, along the contact between Cretaceous sediments and a serpentine intrusion. The zone lies within an extensive anticlinorium. The field had no developments during the year 1939. The production of 9½ bbl. per day is distilled and the gasoline and kerosene are extracted. The asphalt residue. is sold for road construction. The gas is compressed and

Jan 1, 1940

By Robert H. Palmer

Sacuranao Field.—Bacuranao field is about 12 miles east of Havana, along the contact between Cretaceous sediments and a serpentine intrusion. The zone lies within an extensive anticlinorium. The field had no developments during the year 1939. The production of 9½ bbl. per day is distilled and the gasoline and kerosene are extracted. The asphalt residue. is sold for road construction. The gas is compressed and

Jan 1, 1940

By W. W. Anderson

A formula for quantitative efficiency is proposed, in which the efficiency value is a function of the improperly distributed material at the gravity of separation effected by the cleaning equipment. The misplaced material is expressed as a percentage of the total material discharged from the equipment. Numerous examples are given, demonstrating application of the formula to various types of separation, including multiple-product separations.

Jan 2, 1950

By William Kent

DURING the discussions at the Philadelphia meeting in February last, † several speakers expressed their doubts of the general accuracy of chemical analyses of steel made by "iron works chemists," and especially of determinations of manganese. Since the meeting,. the discussion of the "practical value of chemical analyses" has been continued at some length in the columns of the Iron Age. †Transactions, vol. ix, p. 529.

Jan 1, 1882

By Donald M. D. Stuart

It gives me great pleasure to accept the invitation I had the honor of receiving through the Secretary of the Institute, to reply to the criticisms made in discussion of the theory advanced in my work entitled, Coal-Dust an Explosive Agent; and to lay before the Institute a further statement of the views which investigations have led me to form upon this subject,

Jan 1, 1897