Search Documents

By Kent W. Pilz

Wet dust suppression can be achieved by 1) confinement of the dust within the dust producing area with a curtain of moisture, 2) wetting of the dust by direct contact between the particles and droplets of moisture or 3) the formation of agglomerates too heavy to remain airborne, or too heavy to become airborne, by combining small dust particles with each other and with the droplets of liquid. From the standpoint of economy, availability and safety, water is the ideal fluid; however, it is not as effective for dust suppression as when small percentages of specially formulated dust control compounds are blended with it. Performance of dust control com pounds is related to surface active agents and surface activity. In all liquids there is an attractive force between molecules which varies inversely as the sixth power of the distance between molecules. Thus, in the liquid phase where molecules are crowded together, the intermolecular forces are powerful; whereas in the liquid-vapor phase where the molecules are relatively far apart, these forces diminish rapidly. In the body of a fluid there is an uneven distribution of forces resulting in an inward pull called surface tension. The force which keeps two surfaces apart or causes them to coalesce is termed interfacial tension. Fluids of high surface tension exhibit poor wetting, spreading and penetrating qualities. Water has the unusually high surface tension of 72.75 dynes per cm at 20°C.

Jan 7, 1972

By J. S. Johnson, W. C. McCulloch

All phases of plant operation must be synchronized so that the A number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units, parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shut- down. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow.

Jan 1, 1943

By V. Rajaram

The oil shales of the Green River Formation in the United States have been considered as a source of liquid hydrocarbons since 1908, with the first retort constructed in Colorado in 1917. However, it was not until 1944 that the mining characteristics of oil shale were investigated in a systematic manner. During the period 1944 through 1956, the Selective Mine and the Demonstration Mine (also referred to as the Anvil Points Mine) were operated by the U. S. Bureau of Mines (USBM) near Rifle, Colorado. Significant progress was made in developing a room and pillar mining method by which oil shale could be mined safely at a very low cost per ton. Mechanical properties of oil shale were determined, safe room spans and roof support techniques were established, and drilling and blasting methods for oil shale were developed. As a follow-on to this USBM effort, a consortium of six oil companies with Mobil Oil Company as project manager carried out a research program during the period 1964-68 at the Mobil mine, located in the vicinity of the Anvil Points mine. Rock mechanics investigations were conducted as a part of this research program, and consisted of laboratory studies, in-situ stress determinations, and roof and pillar instrumentation. This paper will discuss the findings at the Anvil Points mine and Mobil mine to illustrate the stability considerations in underground oil shale mining.

Jan 1, 1983

By W. A. Tiller, W. C. Johnston

A theoretical analysis of alloy solidification in which the effective partition coefficient, k, of the solute is allowed to vary as a function of interface position is performed. A variety of solute distm'butions in the solid is predicted depending upon the functional dependence of k with interface position. Conversely, the variation of k with interface position required to produce a particular solute distributzon in the solid can be calculated. These preciictions have been tested by controlling the width of the momentum boundary layer in the liquid as a function of interface position with a rotating mugnetic field. One of the objects of controlled solidification is to utilize the freezing process for the preparation of crystals of specific materials containing a predetermined distribution of solutes. For example, a thermoelectric power generation material may exhibit a figure of merit, 2,' as a function of temperature, T, and solute concentration, C, as illustrated in Fig. 1. If we wish to use this material in a device between the temperature limits T1 to T2 a significantly greater efficiency will result from the device if the thermoelectric element illustrated in Fig. 1 consists of a range of solute concentrations appropriately located with respect to the temperature distribution rather than using a sample of constant solute concentration. For this reason and many others2 we are interested in programming and controlling the solute distribution in a single crystal

Jan 1, 1962

By A. G. Raine

For the technological age in which we live, with the constant goal of further improvement in the efficiency of mechanized systems, the need for a replacement of the antiquated drill and blast method of shaft construction has been recognized. For over a decade now; the trend in shaft construction has been toward large diameter bored shafts using either raise boring methods or more flexible, rodless "down the hole" boring machine. The limits of conventional shaft sinking have been reached, the mining regulations are more stringent, and the environmental agencies more aggressive, all contributing to the growing need for development of the rodless shaft boring machine. In the last three years in the United States, world shaft construction records have been achieved using a V-Mole machine, designed by Mirth GmbH of West Germany, using American electrics and hydraulics. Shafts of 7.0 meters (23 feet) diameter, totaling 2,255 meters (7,400 feet) in depth have been constructed at high advance rates, yet with unusually low accident rates. Bearing in mind the high cost of today's mining labor and the inherent danger associated with conventional shaft sinking, this alternative method of shaft construction achieves a fast, competitive, low manpower requirement, whilst enhancing a safer environment for the labor force. Recent results have proven that program time savings of 50 percent over conventional shaft sinking can be achieved which can be directly translated into improved client cash flow projections and more accurate project budgeting.

Jan 1, 1984

By Arthur W. Griffith

Ozark Lead Company, a wholly owned subsidiary of Kennecott Copper Corporation, was formed in 1961 to operate in the State of Missouri. The orebody presently being mined was discovered in January of 1962, and over a quarter of a million feet of drilling was done to determine its value and extent. In addition, a development shaft, six feet in finished diameter, was drilled into the orebody by an oil field rig in order to support the results of the core drill samples and to obtain bulk samples of ore for metallurgical pilot plant testing, upon the results of which the primary flowsheet was established. The design criteria developed from the flowsheet was based upon a 6000 TPD plant throughput and the subsequent engineering and construction of the mine and concentrating plant was completed in June 1968. The plant, which is designed to mine and mill 6000 tons of ore per day and produce 60,000 tons of lead and 8000 tons of zinc in concentrate annually, is located approximately 110 air miles south- west of Saint Louis. MINERALOGY The orebody occurs in the Bonneterre dolomitic limestone formation in the form of irregular masses of disseminated sulphides in essentially horizontal beds. The Lamotte sandstone underlies the Bonneterre formation and is barren in values. Principal ore minerals include galena with lesser amounts of sphalerite and some copper minerals. Galena is found to be massive

Jan 1, 1970

By F. Cadena

HIWASSEE Dam, now under construction by the Tennessee Valley Authority on the Hiwassee River, a tributary of the Tennessee River, will require aggregate for approximately 800,000 cu. yd. of concrete. Near the damsite deposits of natural sand or gravel are not available and graywacke, a rock that is found in abundance, suggested itself as a likely source of manufactured aggregate. Graywacke is a metamorphosed sandstone composed principally of a mixture of quartz (65 per cent), mica (25 per cent), and feldspar (10 per cent). Other minerals are pres-ent in negligible amounts. The rock varies in different parts of the quarry from very fine to a coarse grain containing particles of about 1/4 in. maximum size, although the bulk of the deposit is medium grain. Exten-sive tests showed that graywacke would be suitable as a source of both coarse and fine aggregates. The aggregate plant available for use at Hiwassee Dam consisted of the coarse-aggregate and sand plant used on the Norris project. The coarse-aggregate plant had also been used at Chickamauga Dam. Although most of this plant equipment is now in use at Hiwassee, the present flowsheet is not only different from that at Norris and Chicka-mauga but is also unique as compared to the flowsheet of the average crushed-stone aggregate plant. It is hoped that this paper will show the importance of proper arrange-ment of equipment if the optimum in flexibility and capacity is to be attained.

Jan 1, 1939

By James B. Duke, Ernest W. Greene

An idea of what is meant by "Ultrafine Minerals Or Slimes" as used in the title can be had by an examination of Fig. I. Particle size distributions are presented for a crude kaolin clay, a coarse fraction and a fine fraction. The crude kaolin as mined was blunged with water, degritted through a 325-mesh Tyler screen, and dispersed with sodium silicate. The dispersed crude was then centrifuged in the laboratory into the coarse and fine fractions shown in the figure. The distribution curves were obtained by the well known sedimentation technique of Casagrande' using a long arm centrifuge to obtain equivalent spherical diameters down to 0.2 microns on the finer fraction. Fig. 1 shows the coarse fraction kaolin to be 50% finer than 3 microns, while the crude kaolin is 50% finer than 1.4 microns, and the fine fraction 50% finer than 0.6 microns. For comparison 53 microns on the horizontal scale would represent Stokesian diameters which would just pass a 325- mesh Tyler screen, taking into consideration the Andreasen sieve correction factor of 1.22 X the screen opening.' Another helpful comparison is the surface areas, which in square meters per gram, are 0.044 for 53 micron particles, 0.77 for 3 microns, 1.65 for 1.4 microns, and 5.0 for 0.46 micron particles. Fig. 2 is an electron micrograph of a similar fine fraction kaolin showing the hexagonal plate- like particle shapes.

Jan 10, 1962

By H. Foster Bain

[Secretary's NoTE.—This paper, presented in oral abstract at the San Francisco meeting, was not at first supposed by Mr. Rain to be required for publication in the Transactions; and the excursion to Japan, in which he took part, immediately after the San Francisco meeting, delayed his presentation of the manuscript. After his return to San Francisco, Mr. Bain, in view of the importance of his paper and its discussion, kindly furnished it in full. The delay in its publication (since it was received in April last) has been due, partly to the circumstance that other contributions had meanwhile acquired the " right of way," and partly to the consideration that, the situation contemplated in Mr. Bain's paper having remained practically unchanged, the paper and its discussion would not lose force or timeliness by this lapse of time.—J. S. ] No acute observer of public affairs can have failed to observe a growing disposition on the part of the public to change emphasis in government from political equality to social justice. When our own government was founded it was felt to be sufficient to secure to each individual the fullest possible freedom of opportunity, and such a scheme was excellently adapted to the rapid development of a large territory having a small population. As the number of people in a given area increases, there are more points of contact and conflict; each must move in a smaller orbit, and there must be more regula-

Jan 1, 1913

By R. C. Wilcox, R. V. Lawrence, P. A. Calhoun

The V-Rh-Si, Nb-Rh-Si, and Cr-Rh-Si systems were investigated to evaluate the extent of solid solubility between binary Cr3O structures. All Cr3O components lie within the favorable atomic size range1 for the formation of the Cr3O structure. Previous studies indicated complete solid solubility between V3Si and V3Sn2 and no solubility between Sn and cr3si3 or Si and Nb3Rh.4 The Cr3O structure is not found in the Cr-Sn and Nb-Si binary systems. Powder compacts were are-melted under argon, homogenized in a vacuum at 1000°C, and water-quenched. Alloys containing greater than 15 at. pet Si were annealed 100 hr. X-ray diffractometer methods were used to study all systems utilizing copper radiation for the Cr-Rh-Si system and chromium radiation for the other two systems. V-Rh-Si System. The alloys prepared in the V-Rh-Si system and the measured lattice parameters for the Cr3O structure found in each alloy are listed in Table I. The characteristic Cr3O diffraction pattern was found in all binary alloys. The measured lattice parameter of V3Rh (VRS-1) is in agreement with the reported value5 while the value for V3Si (VRS-5) is only in fair agreement.' In

Jan 1, 1965

By T. Egleston

The Boston and Colorado Smelting Works are situated in the town of Black Hawk, Gilpin County, Colorado, on the Clear Creek Narrow Gauge Railway, 55 miles from Denver, in the Rocky Mountains, at an altitude of 7800 feet. It was one of the first works erected for the metallurgical treatment of gold ores, and the only one established in Colorado on a large scale which has been uniformly successful. Both gold and silver ores are treated, and gold, silver, and copper produced. The lead is not separated from the ores nor paid for, if it exists, and is entirely lost in the residues. The works were planned and built by Professor Hill, formerly Professor of Chemistry in Brown University, Providence, R. I., and is still managed by him, assisted by Mr. Richard Pearce, formerly professor in the School of Mines at Truro, England. They are very advantageously situated with regard to the ore-producing regions, having Boulder County on the north, which produces, besides ordinary gold ores, a series of tellurium minerals, such as altaite, sylvanite, and hessite, which are very rich in gold and silver. They are associated with copper and iron pyrites, blende, galena, and the carbonate and oxides of iron. Gilpin County itself produces for the most part the pyrites of iron and copper rich in gold, with a small quantity of galena and blende, which is rich in silver. In

By Cyril Stanley Smith, Earl W. Palmer

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization. MATERIAL USED After some preliminary heats had been made in the laboratory to determine the effect of copper, several castings from commercial air-furnace heats were obtained, and data from these alone are given here. Part of the metal was poured directly and part was treated in the ladle with the desired amount of copper before pouring. Green-sand molds were used, each holding two tensile test pieces of the form adopted by the Malleable Iron Research Institute, or two bars for graphitization studies, 5/8 in. in diameter and 9 in. long, fed through two enlarged sections equidistant from the middle and ends of the bars. Risers of suitable size insured sound castings. Tensile tests were made

Jan 1, 1935

As 1970 develops and industrial minerals stand at a crucial point in their progress, research and development programs appear to be the key needed to open up new uses for each mineral's future growth. Radically new processes are needed for making a host of new synthetic products from mineral raw materials which will more nearly meet the demanding specifications required for high performance in space, nuclear and defense applications. Consumer applications for high temperature environments will be needed and are important for continuing the nations economic mineral position. In addition, an acute materials problem limits the effectiveness of some of the newer concepts for controlling ail pollution. What is needed then, according to a report printed by the National Academy of Sciences, is the carefully planned development of a limited number of major centers at universities to provide for both basic research and training of personnel; the nurturing of interdisciplinary mechanisms for research and problem solving within these centers; the achieving of a better balance between physics and chemistry within research, emphasizing the chemical aspects of the material sciences; and the enhancement of a broader professional identity by unifying the various disciplines involved into a possible federation of existing societies which have an interest in the problems. [EE] presents its 1969 annual industrial minerals review, where individual authors evaluate the status of each industrial mineral and recount the major developments which occurred during the year.

Jan 1, 1970

By H. D. Hoskold

This paper is presented in fulfillment of the promise made in my paper, " Remarks upon Surveying-Instruments,"" etc., and much of the material which would constitute an appropriate introductioil here is omitted, because it has been already published by the Institute, in connection with my own contributions- or those of Mr. Scott and others, in vols. xxviii. to xxxi. of the Transactions, and in the special Institute volume on Mine-Surveying Instruments. In these preceding publications will be found, for instance, descriptions of the writer's " miner's transit-theodolite" of 1863,† and his later " angleometer,"‡ both of which were steps of the progress in engineering instruments and methods which originated in the work of Bourns, before 1842, on the " BoxTunnel " of the Great Western railway in England, in which he had to make connections by direct telescopic sights down the shafts. About 1870 the writer devised a practical and much superior plan, and made detailed drawings for an instrument to meet all the conditions he had proposed prior to that year. The detailed plans were communicated to a celebrated optical firm in London; but, owing to their loss (in Paris or Germany, it is believed) and to other reasons, the matter was, for the time, allowed to lapse. Following upon Bourns's idea, my friend, the late Mr. Beansland, introduced, in 1856, a new system and a portable astronomical instrument.§ Such instruments, however, were neither common nor convenient, and did not come into general use among engineers.

Jan 1, 1902

By R. H. Harrington

THE definition of precipitation-hardening is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening. This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.-Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheat-ing to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (1) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats.

Jan 1, 1936

By Richard L. Ashbrook, John F. Wallace

Several high-temperature eutectics of cobalt and nickel alloys were modified by small additions of selected elements. Thes-e alloys were compared to unmodified melts for microstructural variations. A few modified compositions were selected on the basis of structure and their tensile and stress-rupture behavior determined. The results of stress-rupture tests in air at 1800 F and room-temperature tensile tests of four high-temperature eutectics showed modification capable of producing substantial improvements in properties. The microstructures were altered and mechanical properties improved by: a.) dispersing a subordinate phase more uniformly throughout the matrix; b) replacing large continuous -network or platelike constituents with small equiaxed discontinuous phases; and c) by forming new, finely divided phases. tHE term "modification" is most commonly used to describe the refinement in microstructure of the Al-Si eutectic that occurs as a result of rapid cooling from the melt or on slow cooling after treatment with small amounts of sodium.1 "Modification" has also been used to describe the change from flake to spheroidal graphite in the austenite-graphite eutectic of cast iron.2 This change of graphite shape is accomplished by small additions of cerium or magnesium.3 Other systems have also been shown to be capable of modification, for example: Pb-Sn by copper;4 Al-Cu by sodium;5 Al-Mn by sodium;5 and Pb-Sb by aluminum.5 Although modification of Al-Si alloys and cast irons is usually accompanied by improved mechanical properties, a general definition of modification has been suggested to include the effect of small quantities of impurity elements on the microstructures of all eutectic alloys, regardless of the effect on the mechanical properties.6 In this paper, the term "modification" is employed in a broad sense to include the formation of third phases or even the supplanting of one of the binary eutectic phases by a third phase. The mechanism of modification, as for any solidification phenomenon, must be considered primarily in terms of nucleation and growth. Although both nuclea-tion and growth mechanisms are required to explain all the phenomena observed in connection with the solidification of modified eutectics, various investigators have usually favored one or the other.7"16 It has been shown that modification of a binary eutectic can be effected by addition of a solute element that has greatly different distribution coefficients or k values in the two phases of the eutectic. Under these conditions, differences in the temperatures at the solid-liquid interfaces of the two phases retard the growth of one phase with respect to the other.4 It has also been shown that increased undercooling favors a transition from a rodlike eutectic to a globular eutectic.17 A mechanism proposed for the transition from lamellar to rodlike eutectics depends on the concept of constitutional super cooling.18 The modification of eutectic alloys may be of interest for high-temperature service as well as at room temperature. Although "high-temperature eutectic alloys" may appear to be a contradiction in terms, many eutectic systems, including those studied in this work, have melting points in excess of 2400°F. One of the mechanisms by which high-temperature alloys are strengthened is dispersion of a relatively brittle phase such as an oxide, carbide, or an inter-metallic compound throughout a ductile matrix. For a given volume fraction of dispersed phase, strength is increased by decreasing the size and spacing of the dispersed particles.19'20 Furthermore, room-temperature ductility may also be increased by changing the shape of a brittle dispersed phase from platelike to equiaxed or spheroidal.8 Overaging and redissolving of the secondary phase limit the maximum temperature to which precipitation-hardened alloys can be used. However, in a binary eutectic system, both phases coexist up to the melting point. Although all eutectic structures are not completely stable,21 a dispersion-hardened cast high-temperature alloy might result if a fine distribution of one of the eutectic phases could be obtained during solidification. An additional reason for interest in eutectic alloys is their excellent castability.22 Since eutectic alloys, like pure metals, freeze at a single temperature rather than over a range of temperatures, their castability is superior to solid-solution alloys with long liquidus to solidus ranges. The purpose of this research was to study the effects of small solute additions on the microstructure and mechanical properties of a number of high-melting-point eutectic compositions.

Jan 1, 1967

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today's most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959

By W. W. Anderson, S. Razi

Electroluminescetrce of single crystals of terbium-(loped ZnS prepared by vapor-transport technique shows the sharp line specirum characteristic of the 4f— 4ft,ansitiotzs of the trivalent Tb3 rotz. V-I tt~easuverr~ents give evidence of space-ellarge-lirrlited curvent but the thrveshold for trap-filled law behavior is not iu agreement with Lampert&apos;s theory for. Single injection. Variations of &apos;brightness with applied voltage, the observation of double peaks its brightness because joms, and the spatial distribution oi electroLur?zir~escerrce indicate that the accelet~atiotz-collision mechanism involving the bst lattice and/ov shallow traps is most likely to be responsible fov excitation of&apos; electrolnminescence. Efficiency rtreusuver)~etits show the quantwn efficiency to be about 10 pct and powev efficiency about 0.05 pct. Effect of anr~eallng the crystal in sulfur vapor is to enluztzce llle rare-earth emission. It rs pvoposed tlzat sulfitv anr~ealing crreates acceptorr-lvpe defects with which the donor-type vare-eavtll ion can associate more readily vesulting in enhanced rare-earth emission. A&apos;o such e~zlznr~cerr~etrt is obserued when the crystal is atztrealetl in zinc vapor. Photolianinescence of ZnS doped nith a variety of rare earths also shows tile slurvp l~rze rwve-eavtlz erriission which in sorrretirr~es accompanied by broad band, stvuctureless lattice emission. Photo-atrd electrolutr~itzesce?~ce of ZIIS:Tb slw~rj do!rlit~unt rare-earth emission in the ~ticirzity of 54(3OA corre-sporrdit~g to the transition D* — Fj. Hoz~!el)er, the detailed line structuve of the luo spectvtr is cliffevet~t, irzdicutit~g that different sites are active in the two processes. Decay of rave-eartlr fluorescence in ZnS doped with any of sei!evul vuve eurtlzs car1 be described by a single exporleritial e.scepl joy ZrlS:lIo. Tl~is exceptiotr can be explaitred it~ tevrr~s of tlre closely spaced er~evgy 1e1:els Jov the HO~&apos; iorr. Decay lime measurertzekzts jov ZnS:Tb, using pulsed elect,-ical ar~d pulsed opticcll excitutiorzs, (11-e itz goor1 agrcetrier~t. LUMINESCENCE of rare-earth-doped materials has been a subject of interest for the past 20 years. Within the past few years there has been a considerable increase in rare-earth research motivated in search of new and more efficient laser materials and also due to the use of certain-rare-earth compounds in the preparation of color television screens. The purpose of this study has been to seek an understanding of some of the basic processes involved in exciting the rare-earth luminescence which is associated with transitions within the 4f shell of the trivalent rare-earth ion. Single crystals of ZnS doped with a variety of rare-earth ions have been prepared by vapor-transport technique described elsewhere.&apos; Photoluminescence was excited by a high-pressure short-arc mercury lamp together with suitable glass and chemical filters. For electroluminescence, sinusoidal and pulse excitations were used. 1) ELECTRICAL CHARACTERISTICS 1.1) V-I Measurements. Electroluminescence experiments were performed on crystals of terbium-doped ZnS. The samples were cleaned and etched and indium or In-Ga alloy contacts were alloyed on by heating in H2 atmosphere to 600°C for times ranging up to 10 min. Static voltage-current measurements were made on several samples. Fig. 1 shows the results for a typical sample. For voltage V < 20 v, the V-I relationship is linear giving a resistivity of 2.5 x 109 ohm-cm for this particular sample at room temperature. In the range of 20 to 250 v, I varies as V "3 and at still higher voltages (when electroluminescence is visible to the scotopic eye) current varies as Vs up to 600 v, all at room temperature. At 77"K, for V > 200 v, / I vge5 up to 1000 v. The V-I characteristics at room temperature follow reasonably well the behavior predicted by Lampert&apos; for one carrier space-charge-limited current in an insulator with traps although, as shown later, the expression derived by Lampert2 for the threshold for trap-filled law behavior Vtfl yields an unrealistically low value for trap density if we use the experimental value of 300 v for VtfL. Assuming the case for shallow trapping, the transition from Ohm&apos;s law behavior to space-charge-limited behavior occurs at voltage Vtr given by where no = thermally generated free carrier density, L = length of the sample, e = static dielectric constant, 6 = ratio of free to trapped electron densities, e = electron charge. For the ZnS:Tb crystal, L = 0.5 mm, E = 8.3 €0, Vtr - 20 v, and no = 5 x 10&apos; per cu cm, calculated from the ohmic behavior assuming electron mobility of 100 sq cm per v-sec. This results in 9 = 0= As more and more electrons are injected the Fermi level moves up in the forbidden gap toward the conduction band. If we assume a single-energy level for traps (which is not strictly correct, as we will show later), the current voltage characteristic is profoundly affected when the Fermi level crosses the trap level. The traps are now filled and injected carriers can no longer be immobilized in traps. Hence, current rises sharply with voltage. The transition from space-charge-limited behavior to the trap-filled behavior occurs at voltage VTFL given by

Jan 1, 1968

By P. N. Richards, M. K. Ormay

Commercially hot-rolled low-carbon steel strip may have one of two basic types of orientation texture, depending upon the amount of a iron which was present during the finishing passes. The changes in these textures with varying amounts of cold reduction up to 95 pct have been determined for the sheet surface plane and for parallel planes down to the mid-plane. The development of cold reduction textures has been reassessed on the basis of (200), (222). and (110) stereographic pole figures and pole density or inverse pole figure values. In agreement with the literature, it is shown that the textures can be described in terms of partial fiber textures but alternative descriptions are given for one of the fiber textures, in order to more closely correlate with experimental data. One partial fiber texture consists of orientations of the type (hkk)[011] extending from (100)[011] to {322}(011) in agreement with the literature. At moderate amounts of cold reduction, a second partial fiber texture forms with a <331> fiber axis inclined 20 deg to the sheet normal and a range of orientations centered on one close to (1 11)[112] and reaching to (232)[101] or (322)[011]. An alternative description involves a (111) fiber axis parallel to the sheet normal but capable of rotation about the rolling direction with rotation about the fiber axis. ORIENTATIONS developed in low-carbon steel strip after cold reduction are of commercial importance because they control, in part, the final preferred orientations after subsequent annealing. The method of control however is not understood completely. Some preliminary work indicated that the cold-reduced orientations and the subsequent annealing textures of commercial low-carbon steel were dependent on the orientations present in the material before cold reduction, that is, those present in the hot-rolled strip but, to date, the effects of initial orientations have not been extensively investigated. For this reason, much of the information given in the literature on development of preferred orientation is difficult to assess as details of initial texture and processing conditions are often inadequate or are altered by a subsequent heat treatment such as normalizing.&apos; It is known2 that anomalous results for near surface orientations may be obtained if lubrication during cold rolling is not adequate but whether lubricant was used during the experiments has not always been given, nor has the exact depth below the surface at which determinations have been made. A comprehensive review of cold rolling textures has been made recently by Dillamore and Roberts&apos; and more restricted recent reviews are due to stickels4 and Abe.5 Based largely on the experimental work of Bennewitz,1 reviewers have accepted that the preferred orientations produced on cold reducing low-carbon steel can be described in terms of two partial fiber textures as follows: Partial Fiber Texture A which has a (011) direction in the rolling direction and includes orientations within the spread from (211)[011] through (100)[Oll] to (211)[011.]; there is some controversy as to whether it extends as far as the orientation (111)[011]. As Dillamore6 has observed, the extent of this partial fiber texture depends on the intensity levels selected. Partial Fiber -texture B which has a (011) direction located 60 den from the rolling direction in the plane containing the rolling direction and the sheet normal. There are two directions which satisfy these conditions and orientations in this partial fiber texture extend from (21l)[0ll] through (554)[225] to (121)[101]. The orientations {211}(011) are members of both partial fiber textures A and B and it can be noted that a variant of {554)<225> is within 6 deg of a variant of {111}(112). Barrett7 had postulated earlier that, in addition to orientations which would fall into partial fiber texture A, a true fiber texture with a (111) direction in the sheet normal was present after heavy cold reduction. This fiber texture would include orientations such as {111}(011) and {111}(112). Later investigators, notably Bennewitz,&apos; have discounted this, mostly on the ground that the partial fiber textures A and B, as described above, contain all the strong orientations that have been observed. However in other work it has been reported2 that (222) pole density or inverse pole figure values show a continuing increase with increasing reduction by cold rolling and give values considerably greater than for any other low indices plane. Thus it could be inferred that a (111) fiber texture as described by Barrett would be one which becomes more dominant with increasing cold reduction, whereas Bennewitz&apos; concluded that components such as {554)(225) in partial fiber texture B began to decrease in intensity at high reductions. Following Bennewitz, one would expect a decreasing (222) pole density value (parallel to the sheet normal) with increasing cold reduction. Because fiber textures consist of grains with a range of orientations that have one axis in common, it has been inferred that during deformation the crystal orientations rotate about the fiber axis&apos;74 and that the orientations of crystals that at one stage belong to one fiber texture can rotate on further cold reduction into the other fiber texture through an orientation in which the two fiber textures intersect.&apos; For example,

Jan 1, 1970

The sixty-fifth Congress created a commission on classification and standardization of wages of Government employees consisting of three members of the Senate and three ex-members of the House of Representatives: The Chairman of the National Service Committee has been notified orally by the Vice-chairman that when said Commission reaches the consideration of engineers&apos; salaries in the Government service, request will be made for assistance of Engineering Council. As it is probable that this request will be received prior to the June meeting of Council, it is recommended that action be authorized concerning the appointment of a suitable committee of Council to undertake this work.

Jan 6, 1919