Search Documents

By K. R. Van Horn, L. W. Kempf

Plastic deformation of most commercia1 metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation. A compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful cstimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. Determination of Residual Stresses The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.' Fig. I reproduces some of the data

Jan 1, 1942

By Walter Knox, Charles H. Sawyer

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By L. W. Kempf, K. R. VanHorn

PLASTIC deformation of most commercial metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful estimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. DETERMINATION OF RESIDUAL STRESSES The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.1 Fig. I reproduces some of the data

Jan 1, 1941

By Charles H. Sawyer, Walter Knox

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By L. W. Kempf, K. R. Van Horn

Plastic deformation of most commercia1 metals within a sufficiently low temperature range results in profound changes in structure and properties, of which the causes and effects are not completely understood. One of these effects is the presence of internal residual stresses and strains, which ordinarily do not appear to require specific consideration in most structural applications but which may be quite undesirable in particular instances. For example, in heavy sections that require considerable machining before assembly, residual stresses may be undesirable because of the distortion they cause when their balance is disturbed by machining or otherwise. In addition, the distribution of stresses may be such that it acts in the same direction as the applied load, thus bringing about premature failure or reducing the load-carrying capacity of the member. One source of residual stress in metal structures is the plastic deformation that may occur during rapid cooling from relatively elevated temperatures, as in the cooling of a casting in the mold or the quenching of a heavy section from elevated temperatures during heat-treatment. These residual stresses are usually undesirable because their direction of operation and magnitude cannot be controlled well enough to permit utilization of the changes in properties of the metal that they may bring about. The most convenient manner of controlling such residual stress is by proper selection of the cooling rate or by reheating to a temperature at which plastic flow can take place, resulting in relief of the residual stresses and strains. Both of these methods of control, however, may cause a reduction in the optimum properties obtainable from the previous operation. A compromise must be struck, and if it is to result in the best possible combinations of properties, specific information must be available regarding the magnitude of the stresses and the rate at which they are affected by variations in cooling rate or in reheating temperature. The complete quantitative estimation of residual stress in complicated metal shapes is exceedingly difficult, if not impossible. In simple sections, however, relatively quantitative analysis may be applied and useful cstimations of stress distribution may be made. This paper is concerned largely with the rate of relief, upon reheating, of internal residual stress in simple aluminum-alloy structures. Since even with simple structures quantitative estimation of residual stresses is laborious and costly, an attempt was made to find other means of collecting data upon which commercial heat-treatments might be based. Incidentally, a few data were collected bearing on the problem of relaxation of aluminum alloys. Determination of Residual Stresses The magnitude and distribution of residual stresses in simple aluminum-alloy shapes rapidly cooled from elevated temperatures has been discussed in a previous paper.' Fig. I reproduces some of the data

Jan 1, 1942

By T. J. Bosworth

The effect of hydrogen pretreatment of alumina, magnesia, and zirconia crucibles on reduced oxygen levels in iron charges has been studied. Hydrogen treatment of commercial high-purity magnesia crucibles was observed to produce as high as 70 pct reduction in oxygen content in iron melts. Hydrogen treatment of the commercial high-purity grade zirconia crucibles produced a 25 pct reduction in oxygen levels in iron melts. An average reduction of Knoop hardness of 47 pct was recorded on the iron charges melted in hydrogen-treated crucibles. On the basis of the experiments and the free-energy diagram, it appears that the major source of reducible oxygen to the iron charge is the suboxides and impurity oxides rather than the major oxide of the crucible. Suitable pretreatment of the crucibles to reduce and remove these oxides yields low oxygen levels in iron melted in the crucibles. DURING the last decade, attempts to produce more pure and uniform alloyed metals have brought about the development of many new melting techniques. Notable among these are vacuum-induction melting, inert and consumable-electrode melting, the cold-mold technique, and numerous techniques for removal of impurities by chemical reaction. However great the achievements in this field, metals must still be melted in contact with media of varying reactivity; i.e., gas, ceramic, and slag. Studies have been made to attain an understanding of the reactions that take place during melting, including slag-metal reactions and equilibria, equilibrium of hydrogen and water vapor, and carbon dioxide and carbon monoxide with oxygen in molten iron. These reactions have been treated quite thoroughly. There is one condition, however, that has been widely overlooked, and, to the author's knowledge, only cursive investigation has been made of it. This is the reaction between the ceramic crucible material and the iron charge. In recent years, Hadley and Bianchi' made a series of studies on hydrogen deoxidation of iron in magnesia crucibles. Bianchi2 studied crucible-FeO equilibria in the temperature range 1525°to 1650°C in high vacuum with, however, inconsistent results. Richardson and Jeffes3 in their series of articles on thermodynamic reactions in the making of iron and steel refer to Wentrup and Hieber's4 work on iron and aluminum deoxidation. Their pork included melting iron in alumina crucibles and measuring the aluminum and oxygen content in the iron. Because of the low values obtained, question has arisen of their analytical accuracy.3 Dastur and chipman5 obtained values on hydrogen-oxygen equilibrium in molten iron contained in alumina crucibles similar to those obtained in experiments in the present program. Hochmann6 studied removal of impurities in chromium irons in high vacuum. His results with respect to oxygen level in chromium-iron melted in magnesia crucibles are consistent with results we have obtained.

Jan 1, 1959

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts' Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts' method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts' law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,'4, '6 Fe-Cu,'6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 '77 187 19>2° Fe-Sn,16 and Fe-v.51 '3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961

By F. L. Robertson, C. H. Bacon, J. W. Till

A description is given of the development of a process for making low sulphur steel on furnaces fired with 2 1/2 pet sulphur oil. Slag and metal are analyzed at melt. Slag weight is estimated. A simple method for calculating necessary lime additions for making 0.025 and 0.035 pct sulphur steel is given. DURING the last 15 years John Summers & Sons have been confronted increasingly by the problem of producing a low sulphur steel from high sulphur materials. The principles adopted, the processes used, the data collected on a furnace specially set aside to study this problem, and speculation on future developments are dealt with in this paper. This study is limited to two melting shops which make sheet steel only, of the following analysis: C, 0.06 pct; Mn, 0.33; S, 0.04, 0.035, 0.03, and 0.025; and P, 0.02 and 0.015. All the processes described have reference to the manufacturing of this steel and are not necessarily applicable, without modification, to other steels. The raw materials used are given in Table I. Development of Process About 1934, Schenck's work on phosphorus was applied to frame quantitative rules for the removal of phosphorus, with great success. We could however, neither in our own work nor in the voluminous literature, find any assistance to frame quantitative furnace rules to remove sulphur. Perhaps, we should have persevered with Schenck's outstanding chapter on sulphur in The Physical Chemistry of Steelmaking, but we missed the importance of one (Ss) sentence on p. 478. "Evidently this ratio -------- is [S] the important quantity to be considered from the point of view of chemical reaction; it is clear that the sulphur content of the steel alone, as frequently given in the literature cannot suffice for judging the success of the reaction unless special details are given regarding the sulphur charge and the amount of slag."' We were not however very successful in getting values for Schenck's "n" that agreed with (S) arrived at by our direct analysis. [S] In addition to Schenck's work much attention was given to V value. The formula selected for V was: (SCaO) — 1.57 (2 P2O5) (S SiO2) After plotting many charges a curve was obtained, based upon the relationship between the percentage sulphur in the finished steel and V value, Fig. 1. For a long time this was used as standard with about a 60 to 70 pct success on producer-gas fired furnaces, if all uprising scrap was used and no bought scrap used. An inspection of this curve shows clearly that it is not a quantitative manufacturing process, and that it was not sure enough to go to the trouble and expense of doing stage analysis for P,O,,

Jan 1, 1952

By George F. Weaton, Carleton C. Long, H. I. Najarian

Partial descriptions of the operation of the St. Joseph Lead Company's Joseph-town smelter have been published. In, 1936 the electrothermic production of zinc oxide was described;' in 1939 appeared a description2 of the electrothermic method of producing zinc metal. Inasmuch as the plant capacity has more than doubled, and in view of the fact that operating practices have improved greatly since these publications, it seems worth while to prepare a fresh description of the present-day elec-trothermic zinc plant and practice. Josephtown smelter is situated on the south side of the Ohio River about 3 miles below its confluence with the Beaver River. In addition to river barge, the smelter is served by Pennsylvania state highway No. 18 and by a spur line of the Pittsburgh and Lake Erie Railroad (N.Y.C.). A recent extension of this spur line connects with the Pennsylvania Railroad. As originally contemplated the plant was to handle only the product of the com-pany's own mines in St. Lawrence County, New york, but owing to the incessant demand for zinc and zinc oxide, it has been necessary to supplement New York concentrates with foreign ores (principally from Quebcc and the Argentine). The general operational procedure followed comprises roasting the sulphide con-centrates, converting the sulphur dioxide into sulphuric acid, preparation of a strong-structure sinter from the calcine, crushing &lid sizing of coke, reduction of coke-sinter mixture by electrothermic means, condensation of the evolved zinc vapor to make zinc metal or burning of the zinc vapor to make zinc oxide, collection and packing of the zinc oxide. Dusts recovered by the roaster and sinter Cottrells are treated in the leach plant for separation of lead sulphate, cadmium metal and zinc sulphate. The general flowsheet is shown in Fig. I. Principal Items OF Equipment Roaster Plant Concentrate drier, 6-ft. 'ia. by 4O ft. 5 in., countercurrent, direct gas-fired. 3500-~on concentrate storage in three vertical steel tanks. Five modified Nichols-Herreshoff twelve-hearth roasters, 21 ft. 6 in. in diameter. Four fans for shaft-cooling air. One threedrum Stirling water-tube waste-heat boiler, 4'8 hp., 200 1b. Per sq. in., with connections to upper and lower balloon flues. Direct gas-fired countercurrent rotary-kiln roaster for Cottrell dust. Necessary conveying equipment, described below. Instrumentation consists of: draft indicators, (3d hearth); various manometers; pyrometer served by thermocouples in each hearth, entrance and exit of waste-heat Joseph. entrance and exit of each hot Cottrell; roaster draft recorder and shaft air-pressure controller; temperature recorder and controller (10th and 12th hearths); SO* recorder (waste-heat boiler n

Jan 1, 1944

By C. R. Holmgren

A large consolidated sand core was used in this investigation. Four groups of experiments including gas drives, water drives, and water drives combined with gas injection, were made. The results of the gas-drive experiments indicate that greater ultimate recovery may be obtained by higher pressure gradients. However, other considerations challenge the absolute veracity of this conclusion. Results indicate that with connate water present and a low pressure gradient during a gas drive, less gas is required to produce a given amount of oil. The saturation gradient determined during a gas drive is presented. Results of the water-drive experiments indicate that the recovery of oil is not a function of either gradient Or input rate. The presence of initial gas saturation resulted in a slightly lower final oil saturation. Injection of sufficient gas to maintain the initial gas saturation during a water drive resulted in lower final oil saturation. Introduction With the demand for petroleum products reaching an all-time record high and the location and exploitation of new reserves becoming more difficult and expensive, the oil industry must look to more thorough and efficient methods of producing the petroleum already located. Much of the previous work along these lines is exploratory and suggests a more complete investigation. For example, a great amount of laboratory work has been done on flooding sands initially saturated roo pct with oil. Since sands saturated roo pct with oil rarely, if ever, exist in nature, and because the water content is a vital factor in the ultimate recovery from the sand, laboratory investigations on cores without water must be supplemented by comparable work on cores with water present.1'2 Other investigators have done a considerable amount of laboratory work using gas and water drives.3 Krutter and Day4 have reported results of investigations using cores saturated IOO pct with oil and have concluded that " the ultimate recovery obtained, using air drive, from a completely oil-saturated core depends on the pressure gradients used. The higher the pressure gradient, the greater will be the recovery until a certain Pressure range is reached above which the reward of increased recovery is much smaller for similar increments in pressure." Yuster and Day6 conclude that less gas and less time are required to produce a given quantity of oil at high pressure gradients than at low pressure gradients; they also conclude that an increase in the viscosity of the oil requires a proportionate increase in the gas needed for recovery. Their results indicate that the gas required to produce a given quantity of oil is greatly reduced by the presence of connate water. R. C. Earlougher2 concluded, based on results of water-flooding a large number of

Jan 1, 1949

By H. H. Stout

IN the early fall of 1025, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500° to 1600°F. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F." Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me." The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after confer-ring as to ways and means, decided to go ahead with preliminary laboratory experi-ments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: I. Since brittle cathodes were often unin-tentionally produced, it seemed probable that the laws controlling this type of deposi-tion could be ascertained. 2. We had already proved the gas-clean-ing feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia Uni-versity for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrounded and heated by a resistance coil of Nichrome wire. Broken tough cathodes were used.

Jan 1, 1940

By D. F. Kaufman, V. V. Damiano, G. J. London, L. R. Aronin

Beryllium bicrystals were Prepared by a seeding and floating zone-melting technique from high-purity beryllium single-crystal material. The starting material was given six floating zone purification passes prior to producing the bicrystals. Symmetric, asymmetric, and antisymmetric bicrystals were tested in tension. Included were bicrystals with boundaries both parallel and perpendicular to the tension axis. Modified symmetric bicrystals were also examined in detail. In these cases, the angles made by the slip planes with the boundary were not equal. Failure by (0001) cleavage, (1180) cleavage, and boundary separation were all observed depending on the orientation of these cleavage planes and the boundary with respect to the tension axis. Failure occurred on whichever system experienced the greatest normal stress. The origin of the fractures observed and the operative dislocation mechanisms were investigated by frac-tography and transmission electron microscopy. The results indicate that low-angle boundaries form in close proximity to the bicrystal boundary and act as sites for crack nucleation. It has been concluded that, although macroscopic compatibility was satisfied in many of the bicrystals examined, the bicrysta1 boundary was effective in Producing "early" failure by local bend plane formation as plastic deformation proceeded, followed by cleavage initiation and crack propagation. SINGLE crystals of high-purity beryllium oriented with the basal plane inclined 45 deg to the tension axis exhibit a critical resolved shear stress of about 300 psi and 200 pct extension by slipping only on the basal plane before failure by cleavage on that plane. Single crystals, oriented with the basal plane parallel to the tension axis, deform by prism slip at a critical resolved shear stress of 9000 psi and exhibit an extension of over 100 pct before failure in a ductile manner.' In contrast to the behavior of single crystals, poly-crystalline beryllium deformed in tension or bending exhibits little or no ductility at room temperature. Beryllium's lack of ductility at room temperature has been attributed to its lack of a sufficient number of independent slip systems. Beryllium has only four independent slip modes at room temperature and according to the Taylor2 and von Mises3 criteria at least five independent shear modes are necessary to completely satisfy the strain compatibility conditions at all the boundaries in a random polycrystalline sample. Studies of beryllium bicrystals thus appear to provide a convenient way in which to determine whether the condition of strain compatibility is a necessary and sufficient condition to prevent failure and whether obviously incompatible boundary conditions result in boundary separation. Bicrystal studies, although not providing all of the constraints encountered in polycrystalline samples, do allow one to select very specific orientation relation-

Jan 1, 1969

By C. G. Dunn

It is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.l In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth—processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insuffcient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered: Until recatly observations were .that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro-structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1947

By C. G. Dunn

It is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.l In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth—processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insuffcient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered: Until recatly observations were .that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro-structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1947

By C. G. Dunn

IT is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.1 In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth-processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insufficient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered. Until recently observations were that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro- structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1946

By AIME AIME

ARRANGEMENTS for the Annual Meeting of the Institute were well advanced at the end of December as the following program will show. Heretofore this has been printed separately, but its inclusion in the Annual Review issue of MINING AND METALLURGY will, it is hoped, make it more easily available for reference until the final program is issued, which will be distributed at the meeting. Added details will appear in the February issue. Last year's meeting drew a record crowd of over 2300 which should be exceeded this year. Early reservations at the headquarters hotel, the Waldorf-Astoria, or any other convenient hotel are desirable, as are prompt reservations for the Annual Dinner. No one need worry about too much speechmaking this year, for the honors will be awarded and accepted in a few words instead of a few paragraphs, in seconds rather than minutes.

Jan 1, 1939

By AIME AIME

DESPITE the fact that its membership is spread over every continent of the globe, the Petroleum Division was able to report a very substantial attendance at its meetings. Careful planning on the part of its chairman, J. B. Urnpleby, and his associates resulted in the presentation of a program that was of timely interest -and led to discussions that will unquestionably prove to be of major value to the petroleum engineer and to the oil industry in general. Scheduling of meetings so as to avoid all conflicts made it possible to obtain a higher average attendance at the several sessions* than in previous years, and gave everyone a chance to hear all of the papers that he was interested in. The chairmen of the various meetings are to be congratulated especially for their skill in handling them so that at .no time was there the least indication of lagging interest.

Jan 1, 1930

By William H. Bassett

RECENTLY it has become the custom of retiring presidents to talk of the relations of the Institute to its membership and its constituency- and it seems a good precedent to follow. Past-president Smith reviewed our relations to materials and to society in general. Mr. Bradley spoke of the value and use of our publications and of our educational duties. My message will be in regard to the coordination of our various groups of member interests and of service to industry. This Institute has, within its organization, four divisions and fourteen technical committees--each interested in a separate put very definite subject, and each covering a phase of mining engineering interest. These vary from geology and the geophysical methods of prospecting, to the physics of the structure of metals, truly "from the mine to the consumer"-from the preparation for mining to the final use of that which has been mined.

Jan 1, 1931

By Carl Lee

OXYGEN-FREE high-conductivity copper (OFHC brand) that is now being commercially offered for the first time represents a notable achievement in electro-metallurgy and is the outcome of endeavors that have extended over a long period. Its manufacture is novel in that electrolytically refined copper is melted in electric furnaces and cast into vertical water-cooled molds. The ingots show the "pipe" characteristic of sound gas-free metal and microscopic examination even at high magnification reveals no cuprous oxide in the copper. Owing to the patent situation, the United States Metals Refining Co., the producers, cannot at this time divulge the details of manufacture, but the operations are under precise control so that the castings are of great uniformity and the copper contains no residual deoxidant. Figs. 1 and 2 show photographs of cross-sections of a wirebar and a billet, both vertically cast.

Jan 1, 1933

By E. R. MARBLE

THE introduction of a new fuel, such as natural gas, necessitates careful study where it has not been used previously. At the El Paso smelter natural gas required the installation of apparatus with which no one at the plant was familiar, either as to the type of equipment needed or as to the burning of the gas in it. Observation of existing installations of a similar character and assistance from gas engineers served as a basis to determine what was advisable to use. The gas line entering the plant goes to a metering station equipped with a duplicate system of pressure regulators, a temperature recorder and the gas company and smelter orifice meters in tandem. There are three distribution lines that can be inter-connected at a later date, if necessary, to assist in equalizing the plant load. All the larger lines are of heavy

Jan 1, 1930