Search Documents

By R. C. Earlougher

Based on laboratory tests conducted with the use of fresh core samples as well as a considerable amount of field data obtained from numerous water floods in northeastern Oklahoma, it appears that for any given oil saturation there is a critical maximum velocity above which the oil-recovery efficiency falls off very rapidly. In effect, when a water flood is operated above this critical velocity, the injected water-oil ratio rises extremely fast, thus shortening the economic life of the flood and reducing the ultimate oil recovery. This critical velocity apparently varies considerably with the percentage of oil saturation of the sand, so that in effect the higher the oil saturation at the beginning of a flood the higher the velocity that can be used successfully. In reviewing several of the earlier floods in the Mid-Continent area, it is concluded that most of the failures were due to two things: (I) too low an oil saturation, such as 30 per cent, and (2) too high water-injection rates, Although considerably more field data are necessary to establish definite limits, it would seem that the proper field injection rate for a 330 by 330 or 440 by 440-ft. spacing varies from approximately I bbl. per foot of sand per day where the oil saturation is as low as 30 per cent up to 5 bbl per foot of sand per day when the oil saturation is as high as 45 to 50 per cent, Introduction With secondary recovery by water-flooding receiving more and more attention throughout the industry, a greater working knowledge of multiphase flow under field conditions becomes more and more necessary A great deal of research has been carried on in highly idealized laboratory conditions, from which certain trends have been indicated, but with few exceptions no direct application to field use has been reported. widely varying conclusions have been drawn from the mass of idealized laboratory experiments and often this divergence apparently was due to the neglect of connate or interstitial water. Since interstitial water is such an important factor in water-flooding operations, it then follows that any laboratory flooding experiment must necessarily take it into account; and since it is difficult to set up laboratory models to allow for interstitial water, the next best procedure is to use fresh core samples for such tests. Even this procedure has its difficulties, inasmuch as it is possible to run only one flooding test on each sample, as each sample differs somewhat in character from all other samples. However, this disadvantage can be overcome to a large degree by the use of an extremely large number of samples. The next question that arises is: "IS it possible to get uncontaminated core samples having a true oil and water saturation like that existing in the reservoir?" If the sand under consideration is still in the primary stage of production, with a normal or relatively high amount of gas still in solution in the oil, probably it is not possible to get a nonflushed core. On the other

Jan 1, 1943

By R. C. Earlougher

Based on laboratory tests conducted with the use of fresh core samples as well as a considerable amount of field data obtained from numerous water floods in northeastern Oklahoma, it appears that for any given oil saturation there is a critical maximum velocity above which the oil-recovery efficiency falls off very rapidly. In effect, when a water flood is operated above this critical velocity, the injected water-oil ratio rises extremely fast, thus shortening the economic life of the flood and reducing the ultimate oil recovery. This critical velocity apparently varies considerably with the percentage of oil saturation of the sand, so that in effect the higher the oil saturation at the beginning of a flood the higher the velocity that can be used successfully. In reviewing several of the earlier floods in the Mid-Continent area, it is concluded that most of the failures were due to two things: (I) too low an oil saturation, such as 30 per cent, and (2) too high water-injection rates, Although considerably more field data are necessary to establish definite limits, it would seem that the proper field injection rate for a 330 by 330 or 440 by 440-ft. spacing varies from approximately I bbl. per foot of sand per day where the oil saturation is as low as 30 per cent up to 5 bbl per foot of sand per day when the oil saturation is as high as 45 to 50 per cent, Introduction With secondary recovery by water-flooding receiving more and more attention throughout the industry, a greater working knowledge of multiphase flow under field conditions becomes more and more necessary A great deal of research has been carried on in highly idealized laboratory conditions, from which certain trends have been indicated, but with few exceptions no direct application to field use has been reported. widely varying conclusions have been drawn from the mass of idealized laboratory experiments and often this divergence apparently was due to the neglect of connate or interstitial water. Since interstitial water is such an important factor in water-flooding operations, it then follows that any laboratory flooding experiment must necessarily take it into account; and since it is difficult to set up laboratory models to allow for interstitial water, the next best procedure is to use fresh core samples for such tests. Even this procedure has its difficulties, inasmuch as it is possible to run only one flooding test on each sample, as each sample differs somewhat in character from all other samples. However, this disadvantage can be overcome to a large degree by the use of an extremely large number of samples. The next question that arises is: "IS it possible to get uncontaminated core samples having a true oil and water saturation like that existing in the reservoir?" If the sand under consideration is still in the primary stage of production, with a normal or relatively high amount of gas still in solution in the oil, probably it is not possible to get a nonflushed core. On the other

Jan 1, 1943

By H. D. Keiser

Minor industrial minerals included in this chapter are: the alum minerals, bromine, calcium chloride, epsomite and other natural magnesium salts, iodine, meerschaum, quartz, industrial crystals other than quartz, and nonfuel gases (air, helium, carbon dioxide). Alum Minerals The natural alums comprise a group of hydrated double sulfates, the most important of which are potash alum, KAI(S04)2.12H20, the "alum" of popular usage; ammonium alum, (NH4)AI(SO4)2, known mineralogically as tschermigite; and soda alum, NaAI(SO4)2.12H20. Kalinite, KAI(SO4)2.11H20, and mendozite, NaAl(SO4)2, 11H20, are fibrous monoclinic alums, distinct from the isometric species potash alum and soda alum.4 Alunite, KAI3(S04)2(OH)6, also known as alumstone or alum rock, has been used as a raw material in the manufacture of alum since early times. All the natural alums are highly soluble and occur as surface evaporation products in arid regions or in sheltered places. Potash alum, together with the other natural alums, commonly occurs as an efflorescence or crevice filling in argillaceous rocks and brown coals that contain disseminated pyrite or marcasite. The mineral is derived by the action of sulfuric acid, formed during the weathering of the sulfide, upon alkali-rich aluminum silicates. Ammonia alum is found chiefly in lignite or broad-coal beds and bituminous shales. Alunite is most commonly associated with acid volcanic rocks, where the rock has been largely altered and alunite formed owing to the presence of sulfuric acid solutions or vapors. Aluminum sulfate, which for most uses is the essential ingredient of alum, may be found in saline residues resulting from the evaporation of natural water and may be formed by the action of acid waters upon aluminous rocks. A deposit of natural potash alum occurs in an irregular network of veins associated with sulfur in rhyolite in Esmeralda County, Nevada, about 35 miles west of Tonopah and 10 miles north of Silver Peak. Alum was recovered at a plant operated on the property between 1920 and 1923 by crushing the ore to ¾ in., grinding to minus 80-mesh, and counter-current leaching; the resulting alum solution was then filtered and crystallized. Alunite was of much interest during World War I as a source of potash and during World War II as a source of alumina. The wellknown deposits at Tolfa, Italy, are veins in trachyte and have been the basis of alum manufacture there since the middle of the fifteenth century. Pure alunite is insoluble in water and in common acids, but if it is heated to 500°C it loses its water of hydration, and the residue consists largely of anhydrous potash alum, part of which is readily soluble in water or acids. If the heat is increased beyond 500°C, most of the sulfur combined with the alumina is released as oxides and the residue consists of potassium sulfate and alumina. Thus, either potash alum (and aluminum sulfate) or potassium sulfate and alumina may be made. In the

Jan 1, 1960

By AIME AIME

CLYDE WILLIAMS, after graduating from the University of Utah as a chemical engineer, worked for a time in western mills and smelters. He then joined the U. S. Bureau of Mines and during the World War studied Ordnance Department and Navy problems on ferroalloys and alloy steels at the Cornell University laboratories. Later, as superintendent of the Northwest Experiment Station of the Bureau, he was active in electric furnace and ore reduction work. Clyde then went to South America and surveyed the iron and fuel resources of the Argentine. Returning, he became chief metallurgist of the Columbia Steel Corp., of

Jan 1, 1936

The Secretary of the Treasury, acting through the National War Savings Committee, soliciting the support of patriotic associations in America in the sale of War Savings Stamps, has addressed the following letter to the President of the Institute: It is particularly desirable to have you urge the members of your association to give their assistance wholeheartedly, and to this end we urgently request that you write a letter to each of your members, outlining the aims of this campaign. That you may more easily draft your letter, we mention a few things in which your members could render a special service. Agencies and Sales Stations.-We desire immediately to establish several hundred thousand agencies and sales stations. It is as easy to sell a War Savings Stamp as it is in ordinary postage stamp, and we have launched a great drive to establish sales stations everywhere. The plan is simplicity itself! Your town, city, county or State Director can furnish you with supplies, posters and publicity matter. You can get the stamps from your post office or bank. Such stations should be at every pay window of manufacturing, industrial and mercantile establishments, and at every retail counter in the country. These stamps should be the easiest bought merchandise in the world, and when these agencies are established this end will have been accom-plished. Therefore, please lay extra pressure on the thought of immediately establishing these sales stations.

Jan 3, 1918

In deposits in which the secondary zones are well defined a layer of rich oxidized ore is frequently found immediately to overlie the enriched sulphides, from which it is derived by direct oxidation in place. In deposits that contain oxidizing precipitants particles and masses of residual oxidized ore are likely to be scattered through the leached zone, having been precipitated during migration before reaching the zone of enrichment. This precipitation hinders secondary enrichment and in extreme cases prevents the formation of such concentrations. Residual ores are precipitated by various reagents. Carbonates are formed through the action of the carbonic acid contained in surface waters, and also directly through the replacement of calcite, especially where the containing rock is limestone. Native metals, such as copper, gold, and silver, are formed by the action of reducing agents, among which organic matter and ferrous sulphate are prominent. Kaolin, gouge, and certain shales occasionally act as powerful precipitants through adsorption. Silver is often found as residual chloride, formed through precipitation by the chlorine contained in surface waters. Residual ores are often the result of incomplete solution, the relatively insoluble minerals being left behind during the migration of associated metals; incomplete oxidation and solution often leave residual masses of unaltered, or partly altered, sulphides in the oxidized zone. Such residual particles or masses have commonly been enriched by additions from circulating, metal-bearing solutions. During oxidation under conditions that permit reprecipitation, such as the oxidation of sulphide deposits in limestone, a scat-

Jan 1, 1932

Discussion of the paper of EDGAR L. NEWHOUSE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin: No. 92, August, 1914, pp. 1801 to. 1806. G. C. RIDDELL, East Helena, Mont.-As nearly as I can recall at the present moment, there are only four or five large plants on the continent where the lead on charge is carried in the neighborhood of 40 per cent. These are at Herculaneum, Collinsville, and Federal, Ill.; Trail, B.. C.; and East Helena, Mont. Our object at the latter point is to smelt a maximum amount of Coeur d'Alêne lead sulphides in as compact and self-fluxing a charge as possible, and to this end we are now smelting a mixture that at times carries up to 42 per cent. lead. The monotony of producing the 7,000 tons of bullion shipped each month to. the Omaha and Chicago refineries is relieved somewhat by the fact that the 15,000 tons monthly of Coeur d'Alêne ores that are com-ing to us carry enough zinc to provide the one-half slag used with from 6.5 to 7.5 per cent. zinc clay after day. During the month of March, 1914, three lead furnaces in continous operation, each 136 in. long, averaged 249 tons per furnace clay, exclusive of coke and slag shells, which is smelting at the rate of 5.5 tons per square foot of tuyère area. The

Jan 11, 1914

By Porter W. Shimer

It docs not seem to be generally known that some American pig-irons contain notable amounts of vanadium, and while the present investigation is far from covering the whole range of irons, it is hoped that, at least, it may serve to call attention to the importance of looking for this element. The majority of the pig-irons investigated were made in the Lehigh Valley and neighboring furnaces, using more or less New Jersey magnetite in their mixtures. Many of these ores, and probably all of them, contain a little vanadium as well as titanium; the ore from one of the largest of these mines contains 0.05 per cent, of vanadium and 0.60 per cent. of titanium. Dr. Thomas M. Drown was the first to detect the presence of vanadium in the incrustations1 occurring on certain pig-irons, and he also found this element in a number of magnetites, but the methods for its accurate determination had not, at that time, been well worked out. In a general way, it may be said that the Lehigh Valley pig-irons contain from 0.02 to 0.05 per cent. of vanadium and from 0.10 to 0.20 per cent. of titanium. These elements follow the silicon; that is, the furnace-conditions which produce a high-silicon, low-sulphur iron will cause the maximum reduction of vanadium and titanium, and

Jan 1, 1913

By Moshe Sheinkin, Burke O. Trafton

This paper describes the use of a computer in analyzing the expected return on a mining venture. The computer program is designed to incorporate all aspects of a mining project, including the mine, mill, smelter, and refinery. Data input may consist of the operating variables in each phase such as the mining rate, grades, reserves at the mine, and the technical operating characteristics of the mine, mill, smelter, and refinery. Detailed tax computations are shown for a domestic operating company, for a foreign company and for a foreign subsidiary. In addition, the use of the various options that are available such as expense write-offs or deferments to create tax credits during preproduction years are considered, and its effect on the DCF. The program is also constructed to accommodate changes in metal prices, and escalation of capital requirements and operating costs. Output consists of profit and loss statements for entire projects using different methods of depreciation, cash flows, discounted cash flows, net present value and returns on investment. Returns on investment are computed for equity investment, total investment, and total investment less tax credits. Allowances are made for bank and guaranteed loans. Additional financial statements can be made for the following: a) A mine-mill segment with a concentrate selling schedule b) A mine-mill-smelter complex with a smelter product selling schedule c) Profitability of the smelter separately d) Profitability of the refinery separately

Jan 1, 1969

By A. V. Quine

FOUR years ago several mining operators shook their heads and predicted that Goldfield Consolidated Mines Co. would never be able to mine the zinc-lead ores from the 550 to 650 level areas of the Deep Creek mine. Their prediction was not without apparent justification, for everywhere one gazed, water was spurting or dripping; every hole that was drilled produced more and more water under pressures of 220 to 250 psi, all from apparently unrelated channels. When the volume of water from one level alone reached 2200 gpm with a possible flow of 5000 to 6000 gpm if the area were fully tapped, development work was brought to a halt and the few holes into the water area were grouted off under contract. As zinc prices had completely deteriorated, the workings were allowed to flood. Upon reopening the mine, in late 1950, it was discovered that the relatively few sacks of cement used in the previous grouting operation had done a tremendous amount of good. Consequently it was decided to systematically drill test holes with a longhole machine and diamond drill and to seal all holes with a cement grout solution. After 30,000 ft of drilling, and the pumping of over 20,000 sacks of cement, 15,000 of which were placed in the supposedly impossible 650 level, the company was successful in literally forcing the water out of the ore zones and opening up large tonnages for subsequent extraction.

Jan 3, 1954

By H. M. Chance

THE present value of most coal properties resides largely in the coal remaining to be mined, which thus constitutes the most important asset. The object of this paper is to discuss methods commonly used in computing the value of mineable coal. To distinguish clearly between such coal values and the values of other property, the several kinds of property values may be divided into classes; this is necessary to avoid unintentional omissions of items of importance. VALUE OF COAL RESERVES Judicial decisions prescribe, and appraisers commonly accept, current sales value as the preferred means for determining the value of transferable property. With few exceptions a property is worth the sum that can be realized from its sale by a willing seller to a willing buyer, a sale in which compulsion urges neither party, and between whom there is no community of interest to fix a value; or it is worth at least as much as a responsible buyer will offer for it. Actual sales of like property or bids from responsible buyers for the property, or for substantially like property, are the best established methods for determining values. Only in the absence of such sales or bids can valuations by other methods be entertained, and only for reasons of weight can sales values be set aside. Sales of coal in the ground, as customarily carried out through lease, under royalty agreements, are therefore the most trustworthy means available for determining the value of coal reserves.

Jan 6, 1926

By Kent E. McElhattan

Selecting efficient machinery for an underground mining operation is a highly skilled art that still depends largely on human judgment and experience. In a coal mine, for example, there is no better way to predict the results of operating with a cutting machine or a continuous miner than to go underground with a sharp-pointed miner's pick. The trained eye can detect the depth of point penetration, cleavage planes, roof and floor strata, and many other conditions impossible to determine in a laboratory. Even so, however, an entirely new set of conditions may lie unexposed just a few feet behind the solid face. The candid truth of the matter is that practically nothing is known of the phenomenon of extracting a mineral from a solid. Consequently, the selection of mineral extraction machinery and systems must be based on results obtained elsewhere under apparently similar conditions. A recent study of the problem of equipment and system analysis was conducted in the coal mining regions of West Virginia. This state was chosen for study because it afforded representative sampling. The 172 coal mines investigated ecompassed seam heights ranging from less than 30 in. to over 84 in. and covered virtually all known coal mining conditions except two. The exceptions are the extreme pitch of coal seams in the western United States and British Columbia and the "bumps" encountered in the Rocky Mountains. Both of these extreme conditions are worthy of individual study.

Jan 7, 1969

The American Society of Mechanical Engineers extends an invitation to members of the Institute to participate in an exceedingly interesting excursion on Saturday, November 11. Permission has been secured for a visit to the plant of the Electric Boat Co. at New London, Conn. There will be run a special-test on a high-power 8-cylinder, 4-cycle Diesel engine. A large number of submarine and other engines in various stages of construction will be seen, also the boring of torpedo tubes, cylinders and other equipment for submarines. The drafting rooms and foundry mill also be open for inspection. The party will have an opportunity to see at close range the submerging of several submarines, and an attack on a vessel on the surface, an exhibit which is being arranged by courtesy of Rear Admiral A. W. Grant, who is in command of the submarine forces of the United States. The Boston members will leave South Station on train No. 7 at 8.30 A. M. Those from Providence will board this train at 9.36 A. M. The Worcester members will leave on train No. 745 at 8.36 A. M. The New York contingent will leave the Grand Central Terminal at 8.31 A. M. on train No. 8. This train will leave New Haven at 10.30 A. M. Upon arrival at New London, each group will go directly to the Mohican Hotel, where a "get-acquainted" luncheon will be served

Jan 10, 1916

By C Gunther

In deposits in which the secondary zones are well defined a layer of rich oxidized ore is frequently found immediately to overlie the enriched sulphides, from which it is derived by direct oxidation in place. In deposits that contain oxidizing precipitants particles and masses of residual oxidized ore are likely to be scattered through the leached zone, having been precipitated during migration before reaching the zone of enrichment. This precipitation hinders secondary enrichment and in extreme cases prevents the formation of such concentrations. Residual ores are precipitated by various reagents. Carbonates are formed through the action of the carbonic acid contained in surface waters, and also directly through the replacement of calcite, especially where the containing rock is limestone. Native metals, such as copper, gold, and silver, are formed by the action of reducing agents, among which organic matter and ferrous sulphate are prominent. Kaolin, gouge, and certain shales occasionally act as powerful precipitants through adsorption. Silver is often found as residual chloride, formed through precipitation by the chlorine contained in surface waters. Residual ores are often the result of incomplete solution, the relatively insoluble minerals being left behind during the migration of associated metals; incomplete oxidation and solution often leave residual masses of unaltered, or partly altered, sulphides in the oxidized zone. Such residual particles or masses have commonly been enriched by additions from circulating, metal-bearing solutions. During oxidation under conditions that permit reprecipitation, such as the oxidation of sulphide deposits in limestone, a scab

Jan 1, 1932

By T. W. Watson, D. R. Flynn

,Measurements are reported for the thermal conductivity of four heat-resistant alloys which were measured at the National Bureau of Standards. Data are given for two samples of AISI Type 316 stainless steel covering a combined temperature range from -150° to + 800°C. The thermal conductivities of three samples of AISI Type 347 were measured over the temperature range from -150° to +150C. Thermal conductivity values are given for Carpenter 20 stainless steel from 100" to 800" C. Data are given for Inconel 702, in both the solution-annealed and the age-hardened condition, over the temperature range from -150" to +800C. SINCE 1958 the National Bureau of Standards, at the request of other government agencies or private laboratories, has carried out measurements of the thermal conductivity of a number of metals and alloys. This paper presents available thermal conductivity data obtained in this way on samples of four heat-resistant alloys. The data presented for Carpenter 20* stainless steel are, to the best of our knowledge, the only thermal conductivity values which have been reported for this alloy to date. Although thermal conductivity values for AISI stainless steels 316 and 347 have been reported by previous investigators, the present data are believed to be of particular interest because, for each alloy, the effect on thermal conductivity of small changes in chemical composition can be observed. The data on Inconel 702' are of interest, not only for

Jan 1, 1969

By D. L. Harris, A. M. Gaudin

THE following results, presented here in condensed form,1 were obtained in a preliminary study of the adsorption of n-hexane thiol, hexyl mercaptan, on sphalerite, zincite, willemite, and quartz, from aqueous solution and from a gas. Interest in this subject was aroused by a Belgian report2 of effective use of hexyl mercaptan for flotation collection of oxidized zinc minerals. The relatively low boiling point, 149°C, of the mercaptan3 suggested the desirability of extending the usual measurements of partition of collector between aqueous solution and gas and between gas and mineral. It is believed that this paper presents the first measurements of this type on a flotation system. Attempts were made to carry out the measurements at equilibrium, but as the work progressed it became increasingly doubtful that this desirable condition had been achieved. To control composition and extent of the gas phase, the apparatus was a wholly-enclosed thermally-controlled glass system. Because of these constraints and the desirability of dealing with pure minerals, a scale of operations was chosen in which a few grams of deslimed mineral were used in each test. It was also necessary to choose a particularly sensitive method for mercaptan analysis, and in fact a method that would permit the experimenters to follow the approach to equilibrium. For these reasons mercaptan marked by radiosulphur 35 was used. An analysis was made for the radiosulphur by a modification of the method of Gaudin and Carr.4

Jan 9, 1954

By W. T. Turrall, D. Porter

THE crystal laboratory, Dept. of Physics, Massachusetts Institute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF2) for use in growing synthetic CaFe2 crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF2 crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO2, BaSO4, CaCO3, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, -4 mesh +10 mesh, from a feed containing over 99 pct CaF2. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1952

By Robert J. Willard

The scanning electron microscope (SEM), became commercially available in 1966. Embodying some unique features not provided by conventional electron microscopes, this new electron-optical instrument offers the scientific community a new way of observing the surfaces of materials. In rock mechanics research, the SEM should prove a useful basic tool in characterizing rock fracture on a very small scale and thus contribute to a better understanding of rock behavior at larger scales. This article presents one example of how the SEM is being applied to such research at the Twin Cities Mining Research Center operated by the U.S. Bureau of Mines in Minneapolis. This research center conducts theoretical and experimental studies on a broad range of mechanisms that induce disintegration by the application of energy to rock.1 Some of these studies are concerned with the relation of microstructure to rock behavior and are carried out mainly with the petrographic microscope. At the same time, however, the center recognizes that this relation must be studied through several orders of magnitude, from lattice-size units of rock-forming minerals to field-size rock units. The SEM fits this scheme by extending the capability of the petrographic microscope into smaller orders of magnitude. However, because its resolution is limited to about 200 A at 10,000x, the SEM is not capable of resolving lattice-size units, and hence a conventional electron microscope with a much greater resolution capability is necessary at this order of magnitude.

Jan 6, 1969

By W. J. Nelson, R. B. Nance

Detailed underground geologic mapping at a scale of 1:1200 has been carried out at the Crown II Mine of Freeman United Coal Mining Co., which operates in the Herrin (No. 6) Coal Member. The roof sequence, upward from the coal, includes (1) soft, medium -to dark-gray shale; (2) hard, black, fissile shale; (3) argillaceous nodular- bedded limestone, and (4) fine-pined, shaly, water-bearing sandstone. The first unit is highly lenticular, and any or all may be missing at a given locality. The sandstone has a sheet facies and a channel facies. The Herrin Coal is eroded in channels near the Crown II Mine. Structural features mapped at Crown II include normal and strike-slip faults and limestone "bosses." Less stable roof and wet conditions are encountered where the limestone is thin or missing or where it is broken by natural fractures or by artificial openings that intersect the water-bearing strata above the limestone. Geologic mapping of the underground workings has allowed us to predict faults, fracture zones, and channels ahead of the face for this mine. Some lithologic and structural pattern apparently are random and cannot now be projected. Conventional exploratory drilling is entirely inadequate to map faults or lithology of the roof, but it does indicate the range of lithologic variability, which can be used to project needs for roof supports. Drilling also is useful in locating channels and in mapping regional variation in thickness and facies of the sandstone.

Jan 1, 1983

By J. Cervik, P. C. Thakur, S. D. Lauer

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh coal seam in northern West Virginia under USBM Cooperative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of 14 small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by a surface exhaust fan. The methane capture ratio was poor at 7% to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance, the boreholes should be drilled from a point 30 to 45 m (98 to 148 ft) from longwall pillar over the largest chain pillar. The standpipe should be grouted for at least 6 m (20 ft), and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane migration toward cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45º ± 10º.

Jan 1, 1986